M K Martin Enterprise Inc3950 Steffler Rd Elmira On Ca N3B 2Z3

Tel: 519-664-2752Toll Free 1-855-664-2752 Fax: 519-664-3695e-mail: sales@mkmartin.cawww.mkmartin.ca

Meteor Skid Steer Operator/Parts Manual

rev:1-13

Intensionally Blank

Table of Content

• Registration

• Warranty

• Safety

• Decal Location

• Assembling the Snowblower

• Operating the Skid Steer Meteor Snowblower

• Main Blower Parts

• Electric Control

• Drive Packages “A” - “B” - “B+” - “C” - “C+” - “D”

• Maintenance

• Bolt Torque

------------------------------------------------------------------------------------------------------------------------------

Postage Stamp

M K Martin Enterprise Inc3950 Steffl er Rd Elmira ON CA N3B 2Z3

Fold Here

Please Cut and Return to M K Martin Enterprise Inc

Fold And Tape here Do not tape all edges or use staples

Warranty Regeneration

1

M K Martin Enterprise Inc3950 Steffl er Rd

Elmira On Ca N3B 2Z3---------------------------------------------------------------------------------------------------------------------Purchaser’s warranty protection equipment is valid only when this completed form or a copy of this form is on fi le at M K Martin Enterprise Inc. By fi lling out this form the purchaser has ac-knowledged delivery of equipment and owner’s / operator’s manual and has accepted the condi-tion of the equipment.

Date of delivery to purchaser -------------------------------------------------------

Type of Equipment -------------------------------------------------------------------

Model # ------------------------------- Serial # -------------------------------------

Retailer’s Signature Indicates• Equipment was properly assembled as directed by manufacturer• Equipment was tested for functionally and operates properly• Purchaser was instructed in safe and proper operating procedures• Warranty was explained to purchaser• Purchaser was give the operators manualRetailerSignature ----------------------------------------------------------------

Company ---------------------------------------------------------------

Address ---------------------------------------------------------------

--------------------------------------------------------------- Purchaser’s signature indicates• Acceptance of equipment fully assembled • Received operator’s manual• Clearly understands conditions of warranty• Received instructions of safe and proper operation of equipmentPurchaserSignature -----------------------------------------------------------

Company ---------------------------------------------------------

Mailing address -------------------------------------------------

City ------------------------------------------ Prov/State -------- Postal Code/Zip ---------------

Available phone number -----------------------------------------

Warranty is valid only when it has been received by manufacturer at address

2

Warranty and Limitation of LiabilityAll equipment is sold subject to mutual agreement that it is warranted at M K Martin Enterprise Inc. (Hereaf-ter called the company), to be free of any defects of material and workmanship. The company shall not be li-able for special, indirect consequential, damage of any kind under this contract or otherwise. The company’s liability shall be limited exclusively to replacement or repairing without charge at it’s factory or elsewhere, at it’s discretion, any material, or workmanship defects, which become apparent within one year from the date of purchase. In no event shall M K Martin Enterprise Inc. be liable for special, direct, incidental or con-sequential damages of any kind. The purchaser by the acceptance of the equipment will assume all liability for any damage which may result from the use or misuse by the employees or others. The purchaser shall maintain and service the equipment as recommended in this Operators Manual.

This warranty does not cover Rental/Commercial or Industrial use of this equipment. This equipment is rated as agricultural.

For Rental/Commercial or Industrial use, Warranty is for defects in material and workmanship for a period of 90 days from the date of purchase.

Warranty coverage is null and void unless the Warranty Registration form has been completed and is on fi le at

M K Martin Enterprise Inc3950 Steffl er RdElmira On Ca N3B 2Z3

For your Record

Purchase Date -------------------------------------------------

Model # --------------------------------------------------------

Serial # ---------------------------------------------------------

Please contact your retailer Manufactured by

M K Martin Enterprise Inc3950 Steffl er RdElmira On Ca N3B 2Z3Tel:(519)-664-2752 (855)-664-2752Fax: 519-664-3695e-mail: sales@mkmartin.ca

www.mkmartin.ca

3

SafetyTake Note: Th is safety symbol is found throughout this manual to call your attension to instructions involving yourself and others working around the machine.

• Failure to follow these instructions can resault in Injury or death

Th is Symbol means

-- Attention!-- Become Alert!

-- Your Safety is Involved!

Signal words are used in this manual.

Caution: Indicates a potential hazard situation that may resault in injury.

Warning: Indicates a hazard situation that could resault in serious injury or death.

Danger: Indicates a hazardous situation that needs to be avoided. It is you the operator that needs to be

aware of these dangres!

If you have any questions not covered in this manual please contact your dealer or;

M K Martin Enterprise Inc.3950 Steffl er RdElmira On Ca N3B 2Z3

Tel: 519-664-2752 1-855-664-2752Fax: 519-664-3695e-mail: sales@mkmartin.cawww.mkmartin.ca

4

Skid Steer Decal Location

Both Sidesof Blower

Chute Rotator Shield

Blower Back

Safety --- It’s in your intrest!

Safety Guidelines

Safety or operation is noe of our main concerns, however it is up to the operator to practice cauton!To avoid personal injury, study the following precautions and insist that all those working with you fol-low them as well.Th e Meteor Skidsteer Snowblower has a shield covering the auger motor and the hydraulic lines leading to the motor. Do not use with cover loose or missing.

Replace any decals that may missing or not readable. Location of decals are indicated elswhere in this manual.Do not use this machine while under the infl uance of drugs or alchohol.Th is equipment should not be operated by children: or those unfamiliar with the operation of the Meteor Snowblower. Do not allow persons to operate this machine untill thay have read this manual and/or where instructed by a qualifi ed person.Do not use this machine to push snow as this can resault in the augers to be broken or bent.

When removing ice and snow from themachine; Stop the engine and remove the keys on the Loader and disconet and disconect the chute control wire! Th is will reduce the posability of the blower to be started and causing personal injury.

5

Skid Steer Decal Location

Both Sidesof Blower

Chute Rotator Shield

Blower Back

6

Skid Steer Meteor Snowblower Assembly

For shipping the chute is not installed on the Snowblower.After receiving the blower unpack the chute and attach it to the blower as shown below.

Spacer

Lower Retainer

Anti Friction Ring

Shield

Apply a light coat of grease to both sides of the plastic Anti Friction Ring and center on top of the fan outlet.Next place Chute on top of plastic ring.Position the Lower Retainer below the flange of the fan outlet -- place the Spacer on top of the Lower Retainer and bolt it to th Chute with 5/16x1 1/2 bolts.

7

Operation of the Skid Steer Meteor SnowblowerThis blower is designed to blow snow with a Skid Steer Loader using the hydraulics to power the fan and auger. The chute is controlled with the loader electrics.The blower is a loader attachment and is mounted the same way as all loader attachments. Make sure that the latches are locked in position after attaching the blower.The chute is controlled with the loader electrics. The controller consists of a battery wire, a control han-dle and control wire to the blower. The handle has 2 switches, one for the rotation and the other for the optional powers deflector adjuster. The battery wire has battery clamps for the battery and a plug on the other end to plug into the handle. The clamp with the red sleeve on the wire goes to the positive battery- terminal. Inside the handle is a 20 amp breaker to protect the circuit and the motor. The control wire has 2 sets of wires, one for the rotator and one for the optional powered deflector adjuster. The wires can be routed out of the back of the cab and along the loader arms for less interference with the operator. The second wire will allow you to add the deflector control without replacing the electric control and wires. The switches are momentary rocker switches and will return to off when the switch is let go.

After the blower is attached to the loader including both the electrics and hydraulic line. Start the loader engine and check to see if the blower is turning in the right direction, or it may not be turning at all, as we use a check valve to allow overrunning. If the fan is not turning move the hydraulic control the other way or switch the hydraulic lines at the loader coupling. This will reverse the hydraulic flow. If the chute buttons are reversed according to your preference you may reverse the battery cables at the battery or if only one of the circuits are to be reversed, the chute motor wires can be reversed at the motor connections.

Operating the Skid Steer Meteor SnowblowerWhen starting the blower, gradually bring the blower to full speed. Do not have the engine running at full speed and suddenly open the hydraulic valve. This put a tremendous strain on all drive components. Have the engine running at full speed while blowing snow. This will turn the fan at maximum speed and best performance. Try to keep the blower from becoming overloaded as this will slow the fan speed and a drop in performance. Note: light powder snow will blow better then heavy wet snow. Try to keep the blower level to the ground while blowing. If it seems to ride up over the hard packed surface, tilt the blower ahead slightly. With the loader it is possible to tilt the blower ahead until the auger

digs into the surface. Be very careful when doing this as the auger and the machine could be damaged.

While blowing snow be aware where the stream of snow is going. Do not direct it toward windows, vehi-cles, objects that could be damaged, or people that could be injured.

8

SS Meteor Snaowblower Parts

Item # Part # Description Qty1 519-623003 Fan 12 512-SSC105 Washer 13 512-SSC106 Nut 14 519-751169 Bearing 15 519-6231002 62” Auger 1

519-6631002 66” Auger 1519-7631002 76” Auger 1519-8631002 86” Auger 1519-9631002 96” Auger 1

6 OL Bolt 7/16x1 1/2 c/w lw, n 47 519-6231001 62” Main Body 1

519-6631001 66” Main Body 1519-7631001 76” Main Body 1519-8631001 86” Main Body 1519-9631001 96” Main Body 1

9

Item # Part# Description Qty8 519-6231013 Lower Chute Clamp 29 519-6231014 Chute Clamp Spacer 2

10 519-6231015 Anti Friction Ring 111 519-6231016 Chute 112 OL Bolt 5/16x1 1/2 c/w lw, n 613 519-6231017 Deflector 114 519-6231018 Deflector Hinge Pin c/w fw, Cotterpin 115 519-6231019 Deflector adjuster 116 OL Bolt 1/2x2 c/w ln 117 519-6231020 Deflector Adjuster Pin 118 Shown elsewhare Optional19 Shown elsewhare Optional20 Shown elsewhare Optional21 OL Bolt 3/8x1 c/w lw, n 222 519-6231011 Rotator Shield 123 519-6231010 Rotator Motor 124 OL Bolt 1/4x3/4 c/w lw, n 225 519-6231012 Chute Rotator Mount 126 OL Bolt 3/8x1 1/2 c/w fw, lw, n 427 Shown elsewhare Rotator Motor Wire28 Shown elsewhere Rotator Extension Wire29 Shown elsewhaere Control Handle30 Shown elsewhere Battery wire31 See motor package32 See motor package33 512-SSC103 Fan Shaft 134 512-SSC104 Bering 235 OL Flange Bolt 1/4x3/4 c/w Flange Nut 236 DJA7011 Manual Tube 137 OL Bolt Bolt 3/8x2 c/w lw 3

OL Bolt 3/8x1 c/w lw 438 512-6231007 Auger Motor Cover 139 See Motor Package40 519-6231005 Auger Motor Mount 141 21173 Rubber Grommet 142 OL 1/2” Bent Pin 243 21592 Skid Shoe 244 See Motor Package

10

Skid Steer Meteor Snowblower Chute Control

Item # Part # Description Qty1 24048 Deflector Actuator (Optional) 12 519-6231010 Rotator Motor 13 24040 Battery Cable 14 23971 Control Handle 15 24028 Motor Wire 16 24043 Extension Wire 1

11

Wiring Diagram

View of inside of Handle

Momentary On both ways

20 Amp Breaker

12

Drive PackagesThe following pages have the parts and part numbers for the various drive packages. Please note that though the fittings and the hydraulic lines appear similar they are not necessarily the same. When ordering parts please order from the proper drive package page.

13

Skid Steer Meteor Snowblower Hydraulic Package “A”

Item # Part # Description “A” Package Qty1 23999 Auger Motor2 23985 Sleeve 13 512-SSC117 U Bolt 14 23981 To Fan Motor Hose 15 512-SSC102 Coupler 1 1/4 14T 16 519-62310091 Fan Motor 17 512SSC108 Motor Clamp 28 OL Bolt 5/8x2 1/2 c/w lw, n 49 6801-0604 Hydraulic Adapter 1

10 6400-1210 Hydraulic Adapter 411 23984 Main Hydraulic Hose 212 FF3-4 Male Male Flat Face Coupler 113 FF3-4 Fem Female Flat Face Coupler 114 5604-1212 Hydraulic Tee 215 5503-1212 Hydraulic 45° Elbow 116 512-SSC116 Check Valve 117 23979 Case Drain Hose 118 5602-1212 Hydraulic Tee 119 5406-1204 Reducer Bushing 120 23983 Return Hose 121 23982 Fan to Auger Motor Hose 1

14

Skid Steer Meteor Snowblower Hydraulic Package “B - B+”

Item # Part # Description “B” Package Qty1 24005 Auger Motor2 23985 Sleeve 13 512-SSC117 U Bolt 14 23981 To Fan Motor Hose 15 512-SSC102 Coupler 1 1/4 14T 16 62310092 Fan Motor “B” 1

24004 Fan Motor “B+”7 512SSC108 Motor Clamp 28 OL Bolt 5/8x2 1/2 c/w lw, n 49 6801-0604 Hydraulic Adapter 1

10 6400-1210 Hydraulic Adapter 411 23984 Main Hydraulic Hose 212 FF3-4 Male Male Flat Face Coupler 113 FF3-4 Fem Female Flat Face Coupler 114 5604-1212 Hydraulic Tee 215 5503-1212 Hydraulic 45° Elbow 116 512-SSC116 Check Valve 117 23979 Case Drain Hose 118 5602-1212 Hydraulic Tee 119 5406-1204 Reducer Bushing 120 23983 Return Hose 121 23982 Fan to Auger Motor Hose 1

15

Skid Steer Meteor Snowblower Hydraulic Package “C - C+”

Item # Part # Description Qty1 MK11217 17T Spline Coupler 12 10319 C Spacer 13 “C” 24001 Fan Motor 160cc 1

“C+” 24003 Fan Motor 200cc 4 OL Bolt 5/8x4 1/2 c/w lw, n 45 23988 Fan - Valve Hose 16 512-SSC117 U Bolt 17 5604-1212 Fitting Tee 28 23987 Fan Motor Hose 19 512-SSC116 Check Valve 1

10 5503-1212 Fitting Elbow 111 FF3-4 Male Flat Face Male Coupler 112 23984 Main Hydraulic Hose 213 FF3-4 Female Flat Face Female Coupler 114 5602-1212 Fitting Tee 215 5406-1204 Fitting Reducer 116 23991 Return Hose 1

16

Item # Part # Description Qty17 23985 Sleeve 118 23990 Valve - Auger Hose 119 23999 Auger Motor 315cc 120 OL Bolt 1/2x2 c/w lw, n 221 6400-1210 Adapter 222 6900-1212 Adapter 123 6801-1212 Fitting Elbow 124 23989 Valve Return Hose 125 23998 Divider Valve 126 6902-1212 Fitting Elbow 127 23986 Case Drain Hose 128 6801-0604 Fitting Elbow 129 6400-1212 Adapter 1

17

Skid Steer Meteor Snowblower Hydraulic Package “D”

Item # Part # Description Qty1 MK11217 17T Spline Adapter 12 20253 Spacer 13 24006 Fan Motor 14 OL Bolt 5/8x3 c/w lw,n 45 6400-0604 Adapter 16 6400-1616 Adapter 27 23993 To Fan Motor 18 5502-1616 Fitting Elbow 19 23997 Main Hydraulic Line 2

10 FF 1 Male Male Flat Face Coupler 111 FF 1 Female Female Flat Face Coupler 112 5605-16 Fitting Tee 213 512-SSC117 U Bolt 114 5404-1612 Fitting Reducing Nipple 2

18

Item # Part # Description Qty15 5406-1612 Fitting Reducer 116 5602-1212 Fitting Tee 217 23985 Sleeve 118 5406-1204 Fitting Reducer 119 SSC116 Check Valve 120 23991 Return Hose 121 23995 Valve Return Hose 122 6400-1210 Adapter 223 23990 Valve - Auger Hose 124 23999 Auger Motor 125 OL Bolt 1/2x2 c/w lw, n 226 6902-1212 Fitting Elbow 127 6901-1212 Fitting Elbow 128 23998 Divider Valve 129 23994 Fan Motor - Valve Hose 130 6802-1612 Fitting Elbow 131 23996 Case Drain 1

19

Meteor Skid Steer Blower General Maintenance

• Check hydraulic lines periodically to ensure that they are not rubbing on the frame

• Be on the lookout for loose nuts and bolts, tighten as required

• The electric chute control should not need a lot of attention. Check for wires that may be rubbing or

catching on the frame

Lubrication

• Auger Bearing - grease sparingly every 20-40 hours. By using too much grease the seals will be forced

off the bearing and allow dirt and debris to contaminate the bearing

• Auger -- drive end -- there is a grease fitting on the auger core to lubricate the drive spline. Grease 1

shot every 50-100 hours. This avoids undue wear of the splines in the coupler.

Note:Abbreviations used

OL - Obtain Locallyc/w - Complete Withlw- Lockwasherfw - Flatwashern - Nutln - Locknut

20

Bolt Torque As used on this equipment

Bolt torque table shown below gives torque values for the various bolts used. This chart is for non-lubricated threads. Replace with the same strength bolt.

Torque Specifications. Torque values are identified by their head markings

Diameter SAE 2 SAE 5 SAE 8“A” Lb-ft N.m Lb-ft N.m Lb-ft N.m1/4 6 (8) 9 (12) 12 (17)5/16 10 (13) 19 (25) 27 (36)3/8 20 (27) 33 (45) 45 (63)7/16 30 (41) 53 (72) 75 (100)1/2 45 (61) 80 (110) 115 (155)5/8 95 (128) 160 (215) 220 (305)3/4 165 (225) 290 (390) 400 (540)1 225 (345) 630 (850) 970 (1320)

Allen head cap screws are similar to SAE 8 quality.

These torques are for a reference only. Not all these sizes and grades are necessarily used in this machine. Bolts that are used as a pivot or hinge have to be used with a locknut, therefore only tighten enough to secure the bolt and still allowing the part to rotate freely.

SAE -2 SAE - 5 SAE-8A

28

21