Micro-Controller Interface & Study · PDF file · 2017-10-13Micro-Controller Interface ... 8 Digital Inputs provided using 8 way DIP Switch ... Full Step can be controlled using this

Micro-Controller Interface

& Study Modules

Sci-tech IC-XX Series Interfacing Modules are useful for Teaching/Training to interface

with any Microprocessor, Microcontroller, Embedded and VLSI Trainer Kits. These

Modules are designed to interface with M8XXX Series, MCU Port I/O’s, 50 Pin KXT Bus. All

the Interfacing Modules are enclosed in wooden enclosures or molded plastic or metal

enclosed.


& Study Modules

01. IC-01 ADC-0809 Interfacing Module

ADC module using ADC-0809.

8 bit accuracy ADC chip

Eight Channel on-chip multiplexed ADC.

A/D Conversion time 100 micro sec.

SOC, EOC, O/P enable can be accessed by user.

Provision of 0 to 5V variable source using Potentiometer for One channel.

Eight channel analog inputs are to be provided on Screw Terminals.

Connect to 8255 using 26 pin FRC Connector.

User's Manual with Sample Programs.

02. IC-02 DAC-0800 Interfacing Module

DAC Module using DAC-0800.8 bit accuracy DAC chip

Dual Channel DAC using 2 Nos. of DAC-0800.

DAC Settling time is 100 ns

DAC Output is provided at Two Test Points.




& Study Modules

03. IC-03 AD574 Interfacing Module

ADC Module using AD-574 Chip.


Single Channel ADC Module.

A/D Conversion Time of 15 micro sec.

Analog inputs are provided at Screw Terminals.


User's Manual with Sample Programs

04. IC-04 Digital Input & Output Interfacing Module

8 Digital Inputs provided using 8 way DIP Switch

8 Input LED Indicators are provided

8 Output LED Indicators are provided



05. IC-05 Elevator Simulator Interfacing Module

Four Floor Elevator Simulator model

LED indication for Each Floor is provided

Up & Down Lift position indication by 10 Nos. of LED

Each Floor is accessed using Four Keys provided on board.




& Study Modules

06. IC-06 IC Tester Interfacing Module for IC-7400 On-board two nos. of 14 pin socket and one no. of 16 pin Socket provided.

One 14 Pin IC-7400 IC is provided for testing.



07. IC-07 Four Digit Seven Segment Display Module

Four Digit Seven Segment display.

Display Technique used is Serial in Parallel out shift register technique

For this technique two port pins are used for display.



08. IC-08 Stepper Motor Controller Card with Motor

This Card can Control a Two/Four phase motor

Half Step, Full Step can be controlled using this card.

Clock Wise & Anti Clock wise rotations can be controlled

Speed can be controlled by this controller

Facility to control maximum 2Kg cm Motor is provided.

0.25Kg cm Stepper Motor is supplied along with this module.

Provision for connecting external 5V/12V supply to drive the motor




& Study Modules

09. IC-09 5x4 Key’s Matrix Keyboard Interfacing Module

5x4 Keys matrix Keyboard.

Keyboard consists of 20 keys.

Consist of Hexadecimal numerals from 0 to 13.

Keys are organized as Four Rows & Five Columns Matrix



10. IC-10 16x1 LCD Display Module

16x1 Liquid Crystal Display.

One 16 rows Alphanumeric Characters will be Displayed.

Facility for backlite display.



11. IC-11 16x2 LCD Display Module 16x2 Liquid Crystal Display.

Two 16 rows Alphanumeric Characters will be Displayed.





& Study Modules

12. IC-12 Traffic Light Controller Module

Single Square traffic light display controller

East, west, north, south posts are defined on the PCB for the square.

For each post four LED is provided in Red, Yellow & Green color.



13. IC-13 Temperature Measurement Module

ADC-0809 is used for Analog to Digital Conversion.


A/D Conversion time is 100 micro sec.

Op-amps are provided for signal conditioning of output from sensor.

K-type thermocouple is used for the measurement.

Thermocouple sensor is supplied with the module.

Variable pot is provided for adjusting gain and offset.

Temperature measurement max. up to 99°C is possible



14. IC-14 DC Motor Controller Card with Motor

DAC-0800 is used for Digital to Analog Conversion.

8 bit accuracy DAC chip

SPDT Relay is provided for direction control

Clock Wise & Anti Clock wise rotation can be controlled

Speed can be controlled by this controller

9 Volt DC Motor is supplied with this card.

9 Volt AC Adaptor is supplied with this card.


& Study Modules



15. IC-15 Relay & Opto Coupler Interfacing Module Four SPDT Relays are provided.

Relay outputs NO, NC, COM is provided at Screw Terminals.

Four Opto isolator inputs are provided using MCT2E.

Opto Inputs are provided through 10 pin FRC Connector.



16. IC-16 8x8 LED Matrix Display Module

8x8 LED Matrix Display.

Display consists of 64 nos. of 3mm LED.

LED’s are organized as Eight Rows & Eight Columns matrix.

All LEDs are buffered.

Connect to 8255 using 26 pin FRC Connector


17. IC-17 Thumb Wheel Switch Card

Two Digit Thumb Wheel Switch.

Thumb wheel switch can be set from 00 to 99.

Output of Thumb wheel switch is in BCD Format.




& Study Modules

18. IC-18 Light Sensing Module using LDR. Light Sensing device using LDR

For Alarm indication one SPDT Relay is provided.

Relay output is provided in connector.



19. IC-19 Infrared TX/RX Module for 8051 Infrared Transmitter: IR LED 920nm

Infrared Receiver: Direct TTL output

Baud Rate: 2.4kbps (max)

Carrier Frequency: 38Khz

Connect to TX/RX of 8051.


20. IC-20 Opto Isolated Input Module

8 bit OPTO Isolated input using MCT-2E IC.

OPTO inputs indication are provided by 5mm LED.

OPTO inputs are provided through 16 pin Connector.



21. IC-21 Opto Isolated Output Module 8 bit OPTO Isolated output using MCT-2E IC.

OPTO outputs indication are provided by 5mm LED.

OPTO output are provided through 16 pin Connector

External +12V provision is provided for isolation.




& Study Modules

22. IC-22 101 ASCII Keyboard Module 101 ASCII PC Keyboard interface.

PC Keyboard interface through 89c2051 Microcontroller.

PC Keyboard AT-type Connector is provided

101 ASCII keyboard is provided with this module.



23. IC-23 Real Time Clock (RTC-6242) Module Real Time Clock using IC 6242.

32.678 KHz. Crystal is provided.

Date, Month & Year can be measured.

Seconds, Minutes & Hours can be measured.

Connect through 40/50 pin FRC Connector.


24. IC-24 Seven Segment Display with Matrix Keyboard Module 5x4 Keys matrix Keyboard.



Keys are organized as Four Rows & Five Columns matrix

Study of techniques like software debouching, Keyboard scanning, key closer, two keys lockout, keyboard encoding & Pausing.

On-board Four Digit Seven Segment display.

Display Technique used is Serial in Parallel out shift register technique





& Study Modules

25. IC-25 16x2 LCD Display with Matrix Keyboard Module 5x4 Keys matrix Keyboard.



Keys are organized as Four Rows & Five Columns matrix

Study of techniques like software debouching, Keyboard scanning, key closer, two keys lockout, keyboard encoding & Pausing.

16x2 Liquid Crystal Display.

Two 16 rows Alphanumeric Characters will be Displayed.




26. IC-26 8 Bit AD/DA Interfacing Module

ADC module using ADC-0804.


Single Channel ADC.

A/D Conversion time 100 micro sec.

Single Channel DAC using one No. of DAC-0800

8 bit accuracy DAC chip

DAC Settling time is 100 ns

Analog inputs and outputs are provided on Screw Terminals.



27. IC-27 Level Simulator Module Four Level Simulator model

Level indication is provided using LED

Up & Down Level position indication by 10 Nos. of LED


& Study Modules

Lower & upper level limit can be set by software



28. IC-28 Six Digit Seven Segment Display Module

On-board Six Digit Seven Segment display.

Display Technique used is Decoder technique




29. IC-29 Parallel to Serial & Serial to Parallel Module 8 bit Parallel to serial converter using IC-74165.

Eight Parallel Inputs are indicated by LED.

Serial to 8 bit parallel converter using IC-74595.

Eight Parallel Outputs are indicated by LED.


User's Manual with Sample Program.

30. IC-30 Two Square Traffic Light Module Two Square traffic light display controller

East, west, north, south posts are defined on the PCB for the square.

For each post four LED is provided in Red, Yellow & Green color.




& Study Modules

31. IC-31 Interface for DOT-MATRIX Printer 80/120 Column Dot-matrix Printer interface




& Study Modules

SC-XX Series Study Cards can be connected to the 50 Pins KXT Bus of any 8/16 bit Series Microprocessor Trainer Kits. In this Study Card LED is provided for different signals like Read, Write, Address Lines, Data Lines, Chip Select & Ports depending upon the Peripherals.

8255 PROGRAMMABLE PERIPHERAL INTERFACE STUDY CARD…Model SC-01 24 bit I/O using 8255 Programmable Peripheral IC

All Input/Output ports pins are terminated on 3 eight pin terminals and 26 pin FRC Connector

All Input/Output ports are indicated by 3 mm LED.

Data lines from AD0 to AD7 are indicated by 3 mm LED.

Chip Select, A0, A1, Read, Write are indicated by 3 mm LED.

Hardware Single Step and Full Clock Execution mode are provided.

Single stepping can be performed using micro switch provided on board.

Using this study card all MODE experiment can be performed.

Interface 8085/8086 Kit using 50 pin FRC Connector.



& Study Modules

02 SC-02 8253 PROGRAMMABLE TIMER COUNTER STUDY CARD Three channel Timer/Counter using 8253 Programmable Timer Counter IC.

All Input/Output ports pins are terminated on terminals and 10 pin FRC Connector.

Clock for Counter-0 is internally provided.


Chip Select, A0, A1, Read, Write are indicated by 3 mm LED.

Hardware Single Step and Full Clock Execution modes are provided.





03. SC-03 8155 PROGRAMMABLE PERIPHERAL INTERFACE WITH TIMER STUDY CARD

22 bit I/O with single channel timer using 8155 Programmable Peripherals IC

All Input/Output ports pins are terminated on 3 eight pin terminals and 26 pin FRC Connector

All Input/Output ports are indicated by 3 mm LED.


Chip Select, IO, Memory, Read, Write are indicated by 3 mm LED.







& Study Modules

04. SC-04 8251 USART STUDY CARD

Serial communication using 8251 Universal Synchronous/ Asynchronous Receiver Transmitter IC.

Output is provided on 9 pin D-Type connector.

Data lines from AD0 to AD7 are indicated by 3mm LED.

Chip Select, Read, Write, A0, A1, DTR, DSR, RTS, CTS, TXRDY, RXRDY are indicated by 3mm LED.






05. SC-05 8257 DIRECT MEMORY ACCESS STUDY CARD

Programmable Direct Memory Access controller using 8257 IC.

On-board 2K RAM Provided using 6116 IC for DMA Operation.

8 Inputs are fed through input terminals with 3 mm LED indicator.

Data lines from AD0 to AD7 are indicated by 3mm LED.

Chip Select, Read, Write, A0, A1, A2, A3, Memory-Write, Memory-Read, IO-Write, IO-Read are indicated by 3mm LED.

AEN, Mark, TC, HRQ, DACK0, DACK1, DACK2 are indicated by 3 mm LED.





User's Manual with Sample Programs..


& Study Modules

06. SC-06 8259 PROGRAMMABLE INTERRUPT CONTROLLER STUDY CARD

8 Channel Programmable Interrupt Controller using 8259 IC.

8 Inputs interrupts are fed through input terminals.


Chip Select, Read, Write, INTA, INTR are indicated by 3 mm LED.






07. SC-07 8279 PKDC STUDY CARD

Programmable Keyboard Display Controller using 8279 IC.

All scan lines/return lines are fed through input terminals and 26 pin FRC connector.


Chip Select, Read, Write, INTA, A0 are indicated by 3 mm LED.

Hardware Single Step and Full Clock Execution mode are provided.

Single stepping can be performed using micro switch provided in the board.

8 Digit Seven Segment display with 20 keys keypad interface module can be interfaced with 8279 Study Card. (OPTIONAL)

Using this study card all modes experiment can be performed.


User's Manual with Sample Program.


& Study Modules

08. SC-08 8212 LATCH STUDY CARD

Eight bit Latch output using 8212 IC

Eight buffered latched output are indicated by 3 mm LED.






09. SC-09 LATCH / BUFFER STUDY CARD

8 bit Latch output using 74373 IC.

8 bit Buffer input using 74245 IC.

8 buffered latch output are indicated by 3 mm LED.

Eight Way DIP Switch is provided for buffer input.

Eight bit buffered output are indicated by 3 mm LED.

Chip Select for IC-74245 and IC-74373 are indicated by 3 mm LED.






10. SC-10 6116/6264/62256 RAM STUDY CARD

Random Access Memory using 6264 IC.



& Study Modules

Chip Select, Read, Write are indicated by 3 mm LED.






Specifications, Model Photos and design subject to changes without any notice

Documents

Micro-Controller Interface & Study · PDF file · 2017-10-13Micro-Controller Interface ... 8 Digital Inputs provided using 8 way DIP Switch ... Full Step can be controlled using this