MICROWAVE INTEGRATED CIRCUIT TRAINING LAB MIC04 · * Win7/XP PC control, display and analysis in real time. * 0.5-4.4 GHz Directional Coupler with 35dB directivity. * 0.5-4.4 GHz

Features

1. Microwave Network Analyser VNA04

* 0.04-4.4 GHz PLL Microwave Signal Generator.* 1KHz Frequency Step size and Accuracy. * 1 MHz-4.4 GHz RF Power meter with -70dBm sensitivity.* Win7/XP PC control, display and analysis in real time.* 0.5-4.4 GHz Directional Coupler with 35dB directivity.* 0.5-4.4 GHz Slotted Line with 1.1 VSWR.* 25 different MIC modules provided. * Gold SMA connectors on low loss ceramic substrate.* Wide power range +20dBm to -70dBm.* High measure speed at all power levels.* Measurement in dBm & dB relative.* Teflon cables are provided for low loss interconnects.

Technical Specifications:

Start Frequency : 40.000MHzStop Frequency : 4400.000MHzStep Size : 1KHz to 4GHz adjust in 1KHz stepStep Time : 10ms to 1s adjustableFrequency Control : Virtual Keypad & Rotary KnobFrequency Jitter : <1psPhase Noise : -80dBc/Hz at 10KHz OffsetRF Level : +20 dBm typicalAttenuator : 0-31.5dB adjustable in 0.5dB stepsOutput Z : 50 ohmsConnector : Gold plated SMATimebase : Internal TCXO/ External for SyncFrequency range : 1MHz to 4.4 GHz Power range : -70dBm to 0dBmResolution : 0.01 dB Measurement : dBm, dBr With Digital DisplayRelative Offset : +20.0 to -70.0dBmImpedance : 50 OhmsNetwork AnalyserDisplay : Frequency vs Power level PlotFunction : Automatic Calibration with Display Normalisation, Marker, PAN, Zoom, AutoscalingCalibration Data : Stored in EEPROM

2. Coaxial Slotted Line

S11: S12: >15dB, <1.5dBResolution: 0.05mm/ 0.15degree at 1.5GHz) using vernierCoupling factor:-20dBConnector : SMAResidual VSWR : <1.2Velocity propagation 8 : 1.818X10 m/s

0Wavelength/360 phase : 121mm at 1.5GHzTotal Length : 200mm

3. Directional Coupler

Bandwidth: 1 - 6 GHzInsertion S 12 : 1.5 + 0.5 dBCoupling S13 : 20 + 2dB

Isolation S14: 20 + 2dB Directivity S23: 15 + 3dBUsage: Antenna forward & reverse power & VSWR measurements.Substrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

MICROWAVE INTEGRATED CIRCUIT TRAINING LAB MIC04

Mfd by: Amitec Electronics Ltd.Regd. Off: 504, Nilgiri, 9 Barakhamba Road, New Delhi-110001, India, Works: 4/32, Site-4, Industrial Estate Sahibabad, NCR-201010, India, [email protected], www.amitec.co+91-11-41505510, +91-120-4371276

8. Microstrip Couplers : Coupled Line Directional CCD30

7. Microstrip Couplers : Hybrid Ring Rat Race HRR30

Fc :3.0 + 0.2 GHz

Insertion S 21 : 1.5 + 0.5 dBCoupling S31: 14 + 2dB Isolation S41: 30 + 2dB Directivity S34: 16 + 2dBImpedance : 50 OhmsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc :3.0 + 0.2 GHz

Insertion S21 : 3 dBCoupling S31: 3.5 + 1dBIsolation S41 : 20dBPhase Shift 0: 180

Impedance : 50 OhmsConnector : SMASubstrate : Ceramic Finish : Gold Plated with selective MaskingCover : Scratch resistant

12. Modulator : PIN Diode Variable Attenuator PVA30

13. Microstrip PIN Diode Switchable Attenuator PSA30

11. Microstrip Switch : PIN Diode SPST Switch PSS30

9. Microstrip Filter : Band Stop Open Stub BFO30

10. Microstrip Filter : High Pass Short Stub HPS30

Fc = 3.0 + 1 GHzInsertion Loss : 3 dBIsolation : 20dBReturn Loss : 10 dBAttenuation : 0-20dBControl Voltage : 0.2-9VImpedance : 50 OhmsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc : 3.0 + 1 GHz

Insertion Loss : 1.5dBIsolation : 20dBAttenuation : 20dBImpedance : 50 OhmsConnector : SMAOperating Current : 35mAOperating Voltage : 12V DCSubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc = 3.0 + 0.5 GHz

Insertion Loss: 3.5 dBReturn Loss : 15 dBIsolation : 25dBImpedance : 50 OhmsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Type : Open StubOrder : 3Fc : 3.0 + 0.1 GHzInsertion Loss S 21 : 2.5dBReturn Loss S11 : 10 dBStop Band S21: 20dB

Impedance : 50 OhmsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Type : Short StubOrder : 3Fc : 3.0 + 0.1 GHzInsertion Loss S 21 : 3dBReturn Loss S11 : 10 dBStop Band S21: 20dB


4. Microstrip Couplers : Unfolded Lange Coupler ULC30

5. Microstrip Couplers : Folded Lange Coupler FLC30

6. Couplers : Branch Line Quadrature Hybrid BQH30

Fc : 3.0 + 0.2 GHz

Insertion S 21 : 2.5 + 1dBCoupling S31: 4.5 + 1dB Isolation S41: 20 + 2dB Directivity S32: 16 + 2dBImpedance : 50 OhmsConnector : SMASubstrate : Ceramic Finish : Gold Plated with selective MaskingCover : Scratch resistant

Fc : 3.0 + 0.2 GHzInsertion S21 : 5 dBIsolation S41 : 16dBCoupling S31: 5 + 1dB Phase Shift 0: 90 Impedance : 50 OhmsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc : 3.0 + 0.2 GHz

Insertion S21 : 3.5 + 1 dB Coupling S31: 3.5 + 1dB Isolation S41: 20 + 2dB Directivity S23: 16 + 2dBImpedance : 50 OhmsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant



14. Amplifier : PHEMT Low Noise Amplifier FET30

15. Amplifier : MMIC InGaP HBT Amplifier HBT30

16. Mixer: Double Balanced MIX40

18. Microstrip Resonator : Ring resonator RRR30

17. Microstrip Circulator CIR30

Device : InGaP HBTFc : 3.0 + 1 GHz

Gain : >15dB1dB Compression : 10dBmNoise Figure : 3.5dBImpedance : 50 OhmsConnector : SMAOperating Current : 35mASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Freq Lo/RF : 1.6 - 6 GHz

Freq IF : DC-2GHzConversion Loss : 8dBLO Drive Level : +7dBmLO/RF S :11 -20 + 2dBLO/RF S :11 -15 + 2dBConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Ring ResonatorFc : 3.0 + 0.1 GHz

S11 : -2 + 1dB

S21 : -20 + 2dB

Q : 100 typicalConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc : 3.0 + 0.1 GHz

Insertion Loss : <1dBIsolation : >20dBImpedance : 50OhmsS :11 -15 + 2dBConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Device : PHEMTFc : 3.0 + 1 GHz

Gain : >15dB1dB Compression : 10dBmNoise Figure : 0.5dBImpedance : 50 OhmsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective Masking

23. Microstrip Wilkinson Equal Power Divider WEP30

24. Microstrip Wilkinson Unequal Power Divider WUP30

21. Loads : Mis-matched/matched Loads MMM30

19. Microstrip Half Wave Resonator HWR30

20. Microstrip Tapered Line Transformer TLT30

Fc : 3.0 + 0.2 GHz

Isolation : 15 + 2dB

Insertion Loss : 3.5 + 0.5dBAmplitude Unbalance : 0.5dBPhase Unbalance : <5 degreesConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc = 3.0 + 0.2 GHz

Isolation = 15 + 2dB

Insertion Loss = 3.5 dB + 0.5dBAmplitude Unbalance: 3dBPhase Unbalance : <10 degreesConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc : 3.0 + 0.2 GHz

Return Loss : 20/6/0/0 dBLoad : Quarter wave matched, VSWR 3, Open & Short StubsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc :3.0 + 0.1 GHz

S11 : -2 + 1dB

S21 : -20 + 2dB

Q : 100 typicalConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc : 3.0 + 0.5 GHz

Return Loss : 10 dB at 3GHzVSWR = 3 at DCLoad : 150 Ohms Connector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant



25. Microstrip VCO : Voltage Control Oscillator VCO40

26. Microstrip Schottky Diode Detector SDD30

27. Microstrip Bandpass Filter Tapped Hairpin BFT30

29. Microstrip Filter : Low Pass Stepped Impedance

28. Microstrip Low Pass Filter Open Stub LFO30

Fc = 3.0 + 2 GHz

Return Loss : 10 dB at 3GHzDynamic Range: -30dBm to +20dBmConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Order: 7Fc: 3.0 + 0.1 Ghz

Bandwidth : 500MHzPassband S21 : 2.5dBReturn Loss S11 : 15 dBStop Band S21: 20dB Impedance : 50 OhmsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Type : Stepped ImpedanceOrder : 7F c : 3.0 + 0.1 GHzPass Band S 21 : 1.5dBReturn Loss S11 : 15 dBStop Band S21: 20dB


Order: 7Fc : 3.0 + 0.1 GHzPass Band S21 : 2dBReturn Loss S11 : 15 dBStop Band S21: 30dB Impedance : 50 OhmsConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

Fc : 2.9 + 0.9 GHz

Output Power : +5dBmPhase Noise : -130dBm @ 1MHzHarmonics : -20dBcTuning Voltage : 0.5-20VConnector : SMASubstrate : CeramicFinish : Gold Plated with selective MaskingCover : Scratch resistant

28. Standard Accessories

Scope of Experiments

50 Ohms Matched Termination SMA(M) - 4 Nos, Short termination SMA(M), Teflon based RG316 cables 4 nos SMA(M)-SMA(M), SMA(F)-SMA(F) RF Unit , Software- converter, AppCAD, E-Manual / Installation Video for ease of Learning

* Properties of Directional Coupler: Measurement of coupling factor, Directivity, return loss of a load, main line insertion loss, isolation, VSWR of ports.* Measurement of S11, S12, S21, S22 parameters of microstrip components* Properties of Branch Line Coupler: Measurement of coupling factor, return loss of a load, main line insertion loss, isolation, VSWR of ports.* Properties of Hybrid Ring Rat race Coupler: Measurement of Power division or Decoupling between Sum and Diff arms of a rat race coupler, Measurement of Insertion loss S21 & S41, Measurement of Return Loss/ impedance match at ports 1 & 4 - S11, S44, measurement of Isolation between ports 1 & 3 - S13, Measurement of Phase difference in output arms 2&4 as 180Deg.* To measure gain, isolation, VSWR of ports of mmic amplifier.* To measure Insertion loss, isolation and VSWR of port microwave SPST PIN diode switch.* To measure Insertion loss, isolation and VSWR of port microwave SPST PIN diode Modulator. Operation of PIN diode modulator. Study of square wave modulation of PIN modulator.* Measurement of power division and isolation characteristic of a microstrip 3 dB power divider.* To measure isolation, VSWR of ports of Radial stub.* To measure VSWR of ports of 50 ohms microstrip line, Matched load, open stub, Short Stub, mismatch.* Low pass filter characteristics insertion loss, pass band, port VSWR* Measurement of resonance characteristics of a microstrip ring resonator and determination of dielectric constant of the substrate.

Dimensions: 55x45x18 cmsweight: 5 Kg, Warranty: 1 yr.



Disclaimer: Images shown are Indicative only. Color or Model may differ from the picture shown (Features will remain same or More). Specifications are subject to change without notice due to continuous improvement of product.

Documents

MICROWAVE INTEGRATED CIRCUIT TRAINING LAB MIC04 · * Win7/XP PC control, display and analysis in real time. * 0.5-4.4 GHz Directional Coupler with 35dB directivity. * 0.5-4.4 GHz