Milling Tool Series for Aluminum Pro - A / X / L Mill Series Technew… · · 2016-11-14Milling Tool Series for Aluminum Pro-A Mill ... increases accuracy to the degree of solid

Pro - A / X / L Mill SeriesMilling Tool Series for High Quality Aluminum Machining

Milling Tool Series for Aluminum

▣ Pro-A Mill Insert top face buffed for good chip control and reduced built-up edge

▣ Pro-X Mill Strong clamping due to the concave design of insert bottom

▣ Pro-L Mill New indexable milling tool for high quality machining

02 03KORLOY TECH-NEWS PRO A·X·L Mill

50th Anniversary

CONTENTS

Pro-A Mill

Pro-X Mill

Pro-L Mill

Features ............................................................................... 04Inserts ................................................................................... 05Cutters ................................................................................. 06Modular Adaptors ................................................................ 08

Features ............................................................................... 09Inserts .................................................................................. 12Cutters ................................................................................. 13Modular Adaptors ................................................................ 18

Featuress ............................................................................. 22Inserts .................................................................................. 24Cutters ................................................................................. 25

Pro-A / Pro-X / Pro-L Mill Series

Features ............................................................................... 03


50th Anniversary

Mirrored top face of insert Prevents built-up edges.

Wide lineup of differently sized inserts per depth of cut

Applicable to a variety of milling applications regardless of the depth of cut and cutting width

Optimized chip breaker design and high rake angle insert Reduce cutting resistance and extend tool lifeAdvantages

Aluminum is the third most abundant element in the Earth’s crust, and is remarkable for itslight weight and ability to resist corrosion. Its hardness is relatively low and not applicable for use for machinery parts. Many other compounds are therefore mixed to form an alloy with Al. The most commonly used additives are Si, Cu, Mg, Ni, Mn, and others in order to make aluminum harder or stickier according to the necessity.

These ductile metals tend to cause built-up edges and poor chip control during machining. Once these problems start, the workpiece surface can be seriously damaged. This is the main contributing factor to deteriorating tool life. KORLOY understands this problem and has launched a new aluminum milling lineup, Pro-A / Pro-X / Pro-L Mill, which help reduce or eliminate these problems.

KORLOY milling tool series for aluminum, the Pro-A / Pro-X / Pro-L Mill inserts have a buffed top face to achieve a mirror finish and avoid any chip sticking even at the high temperatures produced by aluminum cutting. Similarly, high rake cutting edges were engineered for better chip low and low cutting resistance, which significantly extend tool life and produce amazing surface finishes.

The Series is made up of Pro-A Mill for small diameters and low depths of cut, Pro-X Mill for general purpose, and Pro-L Mill for high depths of cut. The Pro-A / Pro-X / Pro-L Mill Series was designed to serve as a total solution for all aluminum milling operations, ranging from small and thin to wide and deep applications.

The Pro-A Mill is especially useful for small and deep milling because of V type insert with its high rake angle cutting edges and wide chip pockets. The Pro-A shows excellent performance in multi-purpose milling, notably in copy milling.

The Pro-X Mill features a concave shape on the insert bottom, which functions as a stopper to prevent the inserts from being dispersed. The high rake angle Pro-X Mill inserts were specially designed for general aluminum milling applications, with insert depth of cut variations of max. ap 0.748inch and 0.984inch.

The Pro-L Mill takes advantage of long type inserts with 2 insert screws for secure deep milling, up to max. ap 0.984inch/1.339inch. A set of differently sized inserts significantly increases accuracy to the degree of solid carbide end mills. The Pro-L Mill produces excellent results in high quality aluminum milling.

KORLOY’s Pro-A / Pro-X / Pro-L Mill Series is the best choice for solving unstable tool life problems associated with built-up edge and poor chip control when machining many Aluminum compounds.

Pro-A Mill

Pro-X Mill

Pro-L Mill

Pro-A / Pro-X / Pro-L Mill Series forAluminum Milling


50th Anniversary

■ Buffed top face of insert ensures good chip control and reduces built-up edge■ Small size modular type for aluminum machining ■ Various line up of modular system for aluminum machining ■ For shouldering, curved surface and ramping ■ High rake angle chip breakers ensure excellent surface roughness, and improved cooling and

chip control by the through coolant system, even in deep pocket machining

Insert Top Face Buffed for Good Chip Control and Reduced Built-up Edge

Copying Shouldering Ramping Through coolant system

Series Pro-A mill ThroughCoolant System

Pro-A 2000• Modular Ø1/2~Ø1 1/2• Shank Ø1/2~Ø1 1/2• Insert VDKT11T210N-MA VDKT11T220N-MA

◦

Pro-A 4000• Cutter Ø1 1/2~Ø4• Shank Ø5/8~Ø1 1/2• Insert VCKT220530N-MA

◦

Cutting diameter ØD(inch) Max. RPM

4000 type n(min-1) vc(sfm)

32 25,600 2,57840 23,000 2,89650 20,000 3,24963 18,400 3,65880 16,400 4,132100 14,700 4,628

Workpiece Cutting speed vc(sfm)

Aluminum alloyRm < 280 MPa 3300Rm > 280 MPa 2640

Copper alloy Long chip 830Thermo plastic - 990Aluminum alloy Si < 12% 2640Copper alloy Short chip 1320

Magnesium alloy - 1320Duroplastics - 500

Available Milling Applications

Pro-A Mill Series

Max. RPM as per Cutting Diameter Recommended Cutting Conditions

Pro-A Mill

Pro-A Mill

Application of small-sized Aluminum machining

General application of Aluminum machining


50th Anniversary

• Lmin : when ap=0.315inch• Lmin : Minimum inclination cutting length α° : Max. rampig angle ap : Depth of cut

Lmin = (inch)

1. Ramping 2. Blind hole helical cutting 3. Through hole helical cutting

Designation ØDRamping Blind hole helical cutting Through hole helical cutting

α°(max) Lmin ØDHmax dmax ØDHmax dmax ØDHmax dmax

PASA2012HR 0.5 11.1 1.606 0.961 0.007 0.882 0.007 0.803 0.006

PASA2016HR 0.625 12.6 1.404 1.211 0.011 1.132 0.010 1.053 0.009

PASA2020HR 0.75 10.3 1.738 1.461 0.010 1.382 0.010 1.303 0.009

PASA2025HR 1 7.5 2.404 1.961 0.010 1.882 0.010 1.803 0.009

PASA2032HR 1.25 5.9 3.071 2.461 0.010 2.382 0.010 2.303 0.009

PASA2042HR 1.5 4.8 3.738 2.961 0.010 2.882 0.010 2.803 0.009

PASA4032HR 1.25 18.9 0.921 2.461 0.033 2.382 0.032 2.303 0.031

PASA4040HR 1.5 15.7 1.121 2.961 0.033 2.882 0.032 2.803 0.031

PASA4050HR 2 11.7 1.521 3.961 0.032 3.882 0.032 3.803 0.031

PASA4063HR 2.5 9.3 1.921 4.961 0.032 4.882 0.032 4.803 0.031

PACA4080HR 3 7.7 2.321 5.961 0.032 5.882 0.031 5.803 0.031

PACA4100HR 4 5.8 3.121 7.961 0.032 7.882 0.031 7.803 0.031

(inch)

Insertshape Designation

Cermet Coated Uncoated Dimensions (inch)

Geometries

CN20

00CN

20NC

M32

5NC

M33

5PC

3500

PC35

45PC

9530

PC65

10PC

5300

PC54

00PD

2000

ST30

AG

10H0

1 l d t r d1

VCKT 220530N-MA ● 0.614 1/2 0.219 0.118 0.220

- - - - - -

VDKT 11T210N-MA ● 0.438 1/4 0.113 0.047 0.110

11T220N-MA 0.264 1/4 0.113 0.079 0.110

Pro-A Mill Ramping & Helical Cutting Technical Data

Inserts


50th Anniversary

SpecificationScrew Wrench

Ø1.50 ~ Ø4.00 FTNC04509 (Ø1.50)TW20S

FTNC04511

(inch)

Designation ØD ØD2 Ød Ød1 Ød2 a b E F ap lbsPACA 4150R 3 1.50 1.378 0.50 0.287 0.433 0.250 0.169 0.787 2.165 0.591 0.20

4200R 3 2.00 1.772 0.75 0.413 0.630 0.313 0.220 0.787 2.165 0.591 0.37

4250R 4 2.50 1.969 0.75 0.413 0.630 0.313 0.220 0.787 2.362 0.591 0.64

4300R 4 3.00 2.205 1.00 0.551 0.827 0.375 0.248 0.984 2.362 0.591 0.83

4400R 5 4.00 2.874 1.25 0.708 1.024 0.500 0.319 0.866 2.362 0.591 1.60

PACA4000

Parts

: Stock item

Available Inserts

VCKT-MA

Pro-A Mill

AA 0°

• AR : 0°• RR : -3°

DesignationCermet Coated Uncoated

CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PC54

00

ST30

A

G10

H01

VCKT 220530N-MA ●


50th Anniversary


Ø0.500 ~ Ø1.500 ETNA02505*TS07S

ETNA02506Ø1.250 ~ Ø1.500 FTNC04509 TW20S

(inch)

Designation ØD Ød ℓ L ap lbsPASA 2050R 1 0.500 0.625 0.250 0.169 0.315 0.10

2062R 2 0.625 0.625 0.313 0.220 0.315 0.112075R 2 0.750 0.750 0.313 0.220 0.315 0.202100R 3 1.000 1.000 0.375 0.248 0.315 0.362125R 4 1.250 1.250 0.500 0.319 0.315 0.662150R 5 1.500 1.250 0.500 0.319 0.315 0.84

PASA 4125R 2 1.250 1.25 0.500 0.319 0.590 0.604150R 3 1.500 1.25 0.500 0.319 0.590 0.80

PASA2000 / 4000

: Stock item

Available Inserts

VDKT-MA VCKT-MA

Parts

AA 0°

• AR : 0°~7°• RR : -21°~ -3°

Type DesignationCermet Coated Uncoated

CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PC54

00

ST30

A

G10

H01

2000 type VDKT 11T210N-MA ●4000 type VCKT 220530N-MA ●

* PAMA 2050 · 2062


50th Anniversary

(inch)

Designation ØD Ød Ød1 ℓ L M ap lbsPAMA 2050HR-M06 1 0.500 0.433 0.256 1.299 1.870 M06 0.315 0.02

2062HR-M08 2 0.625 0.571 0.335 1.417 2.087 M08 0.315 0.042075HR-M10 2 0.750 0.709 0.413 1.417 2.205 M10 0.315 0.062100HR-M12 3 1.000 0.886 0.492 1.614 2.480 M12 0.315 0.102125HR-M16 4 1.250 1.122 0.669 1.772 2.717 M16 0.315 0.18

PAMA2000

Designation Available AdaptorPAMA 2050HR-M06 MATA - M06

2062HR-M08 MATA - M082075HR-M10 MATA - M102100HR-M12 MATA - M122125HR-M16 MATA - M16

Available AdaptorsDesignation : PAMA2125HR-M16

Modular Head Threading Measure size(M16)

Adaptor Spec. : MATA-M16-354-S125S-CAdaptor Threading Measure(M16)

: Stock item

Available Inserts

VDKT-MA


Ø0.500 ~ Ø1.250 ETNA02505*TW07S

ETNA02506

Parts

* PAMA 2050 · 2062

Pro-A Mill

AA 0°

• AR : 7°~10°• RR : -21°~ -9°


CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PC54

00

ST30

A

G10

H01

VDKT 11T210N-MA ●


50th Anniversary

Pro-X Mill

■ Strong clamping from the concave design of the insert bottom■ Good chip flow and reduced built-up edge achieved by the insert’s buffed surface■ High rake angle of insert provides good surface finish and low cutting load■ Specially designed for high speed machining of aluminum■ Suitable for square shouldering and curved surface machining

Strong Clamping due to the Concave Design of Insert Bottom

Code System

[ Cutter / Shank type ]

[ Modular Adaptors ]

[ Modular type ]

Pro-X Millseries

PAX C

Tool typeC : CutterS : Shank

M : Modular

5

Insert I/C5 : 19 size insert6 : 25 size insert

Tool diameter ISO : mm

ANSI : inch

250

Arbor typeM : MetricA : Inch

A H

Coolant typeH : Thru-hole

Unmarked : No thru-hole

A

Nose RA : 0.016~0.126B : 0.157~0.197

R

Hand of tool R : Right

L : Left

-

Pro-X Millseries

PAX M

Tool typeM : Modular

5

Insert I/C5 : 19 size insert

Tool diameter ISO : mm

ANSI : inch

125

Arbor typeM : MetricA : Inch

A H

Coolant typeH : Thru-hole

Unmarked : No thru-hole

A

Nose RA : 0.016~0.126B : 0.157~0.197

R

Hand of tool R : Right

L : Left

-

ScrewSize

M16

Modular Adaptor

MAT M10

Scew Size

S075

Shank dia(ø)

Neck Shape S : StraightT : Taper

S

NeckLength

394 C

Shank MaterialS : Steel

C : Carbide

[787]

Shank Length

-


50th Anniversary

Copying Slotting & Shouldering Ramping Hellcal Cutting

Pro-X Mill

※ Screw Torque = 4N•m ※ Indexable insert : 6.8g

551d = 3/4inchd = 1inchd = 1 1/4inchd = 1 1/2inchd = 2inchd = 2 1/2inch

d = 3inchd = 4inchd = 5inch

395

355

236

158

79

0 10000 15000 20000 25000 30000 35000 40000 45000 50000

n(min-1)

vf(ipm

)

Special design for strong clamping that prevents inserts from being dispersed in high speed machining

Various insert corner radii are available (R0.016 ~ R0.197)

Clamping System for High Speed

Centrifugal Force as per RPM

Clamping design as per FEM analysis

Strong clamping of insert

[ Marking ] Designation Max. RPM

3 dimensional chip breaker designfor low cutting load

Plunging, Slotting, Drilling Technical Data

Holderap(inch)

5000 Type 6000 TypeØ3/4 0.315 -Ø1 0.157 0.433

Ø1 1/4 0.157 0.236Ø1 1/2~5 0.157 0.236

Insert ap(inch)XETK19 0.157XETK25 0.236

1. When drilling or grooving, follow the machining sequence in the pic.

2. When drilling or grooving, decrease the feed and cutting speed 30%~50% from the recommended data

Cutting Condition for Drilling



50th Anniversary

Designation ØDRamping Blind hole helical cutting Through hole helical cutting

α°(max) Lmin ØDHmax dmax ØDHmax dmax ØDHmax dmaxPAXSA5075HR 0.75 9.1 2.47 1.264 0.008 1.185 0.007 0.988 0.006 PAXSA5100HR 1.00 11.9 1.86 1.764 0.015 1.685 0.014 1.488 0.012 PAXSA5125HR 1.25 9.0 2.49 2.264 0.014 2.185 0.014 1.988 0.012 PAXSA5150HR 1.50 7.2 3.11 2.764 0.014 2.685 0.013 2.488 0.012 PAXCA5200HR 2.00 5.2 4.36 3.764 0.013 3.685 0.013 3.488 0.012 PAXCA5250HR 2.50 4.0 5.61 4.764 0.013 4.685 0.013 4.488 0.012 PAXCA5300HR 3.00 3.3 6.86 5.764 0.013 5.685 0.013 5.488 0.012 PAXCA5400HR 4.00 2.4 9.36 7.764 0.013 7.685 0.013 7.488 0.012 PAXCA5500HR 5.00 1.9 11.86 9.764 0.013 9.685 0.013 9.488 0.012 PAXSA6100HR 1.00 9.0 2.48 1.764 0.011 1.685 0.011 1.488 0.009 PAXSA6125HR 1.25 6.8 3.31 2.264 0.011 2.185 0.010 1.988 0.009 PAXSA6150HR 1.50 10.8 2.07 2.764 0.021 2.685 0.020 2.488 0.019 PAXCA6200HR 2.00 7.7 2.91 3.764 0.020 3.685 0.020 3.488 0.019 PAXCA6250HR 2.50 6.0 3.74 4.764 0.020 4.685 0.019 4.488 0.019 PAXCA6300HR 3.00 4.9 4.57 5.764 0.020 5.685 0.019 5.488 0.019 PAXCA6400HR 4.00 3.6 6.24 7.764 0.019 7.685 0.019 7.488 0.019 PAXCA6500HR 5.00 2.9 7.91 9.764 0.019 9.685 0.019 9.488 0.019


PAXSA5125HR-A

WorkpieceCutting condition

vc(sfm) fz(ipt) ap(inch) ae(inch)

A6061 4290 0.008 0.32 0.5D

PAXCA5200HR-A

WorkpieceCutting condition

vc(sfm) fz(ipt) ap(inch) ae(inch)

A6061 4290 0.01 0.4 0.5D

Application Examples

Pro-X Mill Ramping & Helical Cutting Technical Data

• Lmin : when ap=0.394inch• Lmin : Minimum inclination cutting length α° : Max. rampig angle ap : Depth of cut

Lmin = (inch)

(inch)

Chip evacuation and good surface roughness Long tool life and no built-up edge & chipping


50th Anniversary Pro-X Mill

Max. RPM as per Cutting Diameter Recommended Cutting ConditionsCutting diameter ØD(inch) Max. RPM

5000 type 6000 type n(min-1) vc(sfm)

3/4 - 15,000 7,5641 1 32,600 8,445

1 1/4 1 1/4 28,800 9,5491 1/2 1 1/2 25,800 10,693

2 2 23,000 11,9162 1/2 2 1/2 20,500 13,382

3 3 18,200 15,0874 4 16,300 16,8905 5 14,600 18,910

※ In case of actual machining, accidental insert or tool breakage could happen even under the written RPM. A special cover or door is necessary to prevent damage from broken insert or broken tool.

Workpiece Cutting Speedvc(sfm)

Feedfz(ipt)

Aluminum alloy Rm280 < MPaRm280 > MPa

3960 0.0123300 0.010

Copper alloyThermo plastic

Long chipping-

1320 0.0081150 0.006

Aluminum alloy Si <12%Si ≥12%

3300 0.010- -

Copper alloy Short chipping 1650 0.008Magnesium alloy - 1480 0.008

Duroplastics - 680 0.006


Coated Uncoated Dimensions (inch)

Geometries

NCM

325

NCM

335

PC35

00PC

3545

PC95

30PC

6510

PC53

00PC

5400

PD20

00ST

30A

G10

H01 l I2 I1 t r d1

XEKT 19M504FR-MA ● ● 0.709 0.646 0.055 0.197 0.016 0.17319M508FR-MA ● ● 0.709 0.646 0.039 0.197 0.031 0.17319M512FR-MA ● ● 0.709 0.646 0.024 0.197 0.047 0.17319M516FR-MA ● 0.689 0.646 0.020 0.197 0.063 0.17319M518FR-MA 0.689 0.646 0.020 0.197 0.071 0.17319M520FR-MA ● ● 0.689 0.646 0.020 0.197 0.079 0.17319M530FR-MA ● 0.669 0.646 0.028 0.197 0.118 0.17319M532FR-MA ● ● 0.669 0.646 0.020 0.197 0.126 0.17319M540FR-MA ● ● 0.650 0.646 0.020 0.197 0.157 0.17319M550FR-MA ● ● 0.630 0.646 0.016 0.197 0.197 0.173250604FR-MA ● 0.965 0.862 0.059 0.250 0.016 0.236250608FR-MA ● 0.965 0.862 0.047 0.250 0.031 0.236250612FR-MA ● 0.965 0.862 0.031 0.250 0.047 0.236250616FR-MA 0.965 0.862 0.016 0.250 0.063 0.236250620FR-MA ● 0.945 0.862 0.020 0.250 0.079 0.236250630FR-MA 0.933 0.862 0.024 0.250 0.118 0.236250632FR-MA ● 0.933 0.862 0.016 0.250 0.126 0.236250640FR-MA 0.898 0.862 0.047 0.250 0.157 0.236250650FR-MA ● 0.894 0.862 0.016 0.250 0.197 0.236

Inserts


50th Anniversary

• A type : Insert NoseR 0.016~0.126 B type : Insert NoseR 0.157~0.197

(inch)

Designation ØD ØD2 Ød Ød1 Ød2 a b E F Max rpm ap lbsPAXCA 5150HR-A,B 3 1.5 1.417 0.50 0.287 0.433 0.252 0.169 0.630 1.50 25,800 0.67 0.15

5200HR-A,B 4 2.0 1.772 0.75 0.416 0.630 0.315 0.220 0.787 1.75 23,000 0.67 0.30 5250HR-A,B 5(4) 2.5 1.772 0.75 0.416 0.630 0.315 0.220 0.787 1.75 20,500 0.67 0.56 5300HR-A,B 5 3.0 2.205 1.00 0.551 0.827 0.374 0.248 0.866 2.00 18,200 0.67 1.00 5400HR-A,B 6 4.0 3.386 1.50 0.827 1.220 0.626 0.394 1.181 2.50 16,300 0.67 2.30 5500HR-A,B 7 5.0 3.386 1.50 0.827 1.220 0.626 0.394 1.181 2.50 14,600 0.67 3.20

PAXCA5000

: Stock item

Available Inserts

XEKT-MA


Ø1.5 ~ Ø5.0 PTKA0408 TW15S

Parts

Recommended Cutting Conditions

AA 0°

• AR : 8°~17.5°• RR : -9.5°~ - 5°


CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PD20

00

ST30

A

G10

H01

XEKT 19M504FR-MA19M508FR-MA19M512FR-MA19M516FR-MA19M518FR-MA19M520FR-MA19M530FR-MA19M532FR-MA19M540FR-MA19M550FR-MA


50th Anniversary


(inch)

Designation ØD ØD2 Ød Ød1 Ød2 a b E F Max rpm ap lbsPAXCA 6200HR-A,B 2 2.0 1.772 0.75 0.416 0.433 0.315 0.220 0.787 1.75 23,000 0.91 0.32

6250HR-A,B 3 2.5 1.772 0.75 0.416 0.630 0.315 0.220 0.787 1.75 20,500 0.91 0.53 6300HR-A,B 4 3.0 2.205 1.00 0.551 1.260 0.374 0.236 0.866 2.00 18,200 0.91 0.73 6400HR-A,B 5 4.0 2.874 1.25 0.709 1.024 0.510 0.319 0.866 2.50 16,300 0.91 1.70 6500HR-A,B 6 5.0 3.386 1.50 0.827 1.220 0.626 0.394 1.181 2.50 14,600 0.91 3.06

PAXCA6000

: Stock item

Available Inserts

XEKT-MA


Ø2.0 ~ Ø5.0 FTGA0513-P TW20-100

Parts

Pro-X Mill

AA 0°

• AR : 8°~17.5°• RR : -9.5°~ -5°


CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PD20

00

ST30

A

G10

H01

XEKT 250604FR-MA ●250608FR-MA ●250612FR-MA ●250616FR-MA250620FR-MA ●250630FR-MA250632FR-MA ●250640FR-MA250650FR-MA ●


50th Anniversary


(inch)

Designation ØD Ød ℓ L Max rpm ap lbsPAXSA 5075HR-A,B 1 0.75 0.75 2.36 5.12 15,000 0.67 0.53

5100HR-A,B 2 1.00 1.00 2.36 5.51 32,600 0.67 0.88 5125HR-A,B 2 1.25 1.25 2.76 5.91 28,800 0.67 1.63 5150HR-A,B 3 1.50 1.50 2.76 6.30 25,800 0.67 2.21

PAXSA5000

: Stock item

Available Inserts

XEKT-MA


Ø0.75 ~ Ø1.50 PTKA0408 TS15S

Parts

AA 0°

• AR : 5°~10°• RR : -14°~ -5°


CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PD20

00

ST30

A

G10

H01

XEKT 19M504FR-MA ● ●19M508FR-MA ● ●19M512FR-MA ● ●19M516FR-MA ●19M518FR-MA19M520FR-MA ● ●19M530FR-MA ●19M532FR-MA ● ●19M540FR-MA ● ●19M550FR-MA ● ●


50th Anniversary Pro-X Mill


(inch)

Designation ØD Ød ℓ L Max rpm ap lbsPAXSA 6100HR-A,B 1 1.00 1.00 2.36 5.51 32,600 0.91 0.93

6125HR-A,B 1 1.25 1.25 2.76 5.91 28,800 0.91 1.68 6150HR-A,B 2 1.50 1.50 2.76 6.30 25,800 0.91 2.65

PAXSA6000

: Stock item

Available Inserts

XEKT-MA


Ø1.00 ~ Ø1.50 FTGA0510-P (Ø1.00~Ø1.25)TW20S-100

FTGA0513-P (Ø1.50)

Parts

AA 0°

• AR : 5°~10°• RR : -14°~ -5°


CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PD20

00

ST30

A

G10

H01

XELT 250604FR-MA ●250608FR-MA ●250612FR-MA ●250616FR-MA250620FR-MA ●250630FR-MA250632FR-MA ●250640FR-MA250650FR-MA ●


50th Anniversary

• A type : Insert NoseR 0.016~0.126, B type : Insert NoseR 0.157~0.197

(inch)

Designation ØD Ød Ød1 ℓ L M ap lbsPAXMA 5100HR-A,B-M12 2 1.00 0.906 0.492 2.165 3.110 M12 0.67 0.12

5125HR-A,B-M16 2 1.25 1.142 0.669 2.165 3.228 M16 0.67 0.245150HR-A,B-M16 3 1.50 1.142 0.669 2.165 3.228 M16 0.67 0.32

PAXMA5000

Designation Available Adaptor

PAXMA 5100HR-A,B-M12 MATA - M125125HR-A,B-M16

MATA - M165150HR-A,B-M16

Available AdaptorsDesignation : PAXMA5125HR-M16

Modular Head Threading Measure size(M16)

Adaptor Spec. : MATA-M16-354-S125S-CAdaptor Threading Measure(M16)


Ø1.00 ~ Ø1.50 PTKA0407TW15S

PTKA0480

Parts

AA 0°

• AR : 6°~8°• RR : -7°~ -5°

: Stock item

Available Inserts

XEKT-MA


CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PD20

00

ST30

A

G10

H01

XEKT 19M504FR-MA ● ●19M508FR-MA ● ●19M512FR-MA ● ●19M516FR-MA ●19M518FR-MA19M520FR-MA ● ●19M530FR-MA ●19M532FR-MA ● ●19M540FR-MA ● ●19M550FR-MA ● ●


50th Anniversary

Fig. 1 Fig. 2

Designation ØD Ød Ød1 L M Fig.MATA M06-078-S038S 0.354 3/8 0.256 0.787 2.756 M06 1

M06-157-S050T 0.354 1/2 0.256 1.575 3.780 M06 1M06-255-S063T 0.354 5/8 0.256 2.559 4.921 M06 1M6B-078-S050S 0.433 1/2 0.256 0.787 2.992 M06 1M6B-157-S050S 0.433 1/2 0.256 1.575 3.780 M06 1M6B-255-S063T 0.433 5/8 0.256 2.559 4.921 M06 1M6B-315-S063T 0.433 5/8 0.256 3.150 5.512 M06 1M08-078-S063S 0.571 5/8 0.335 0.787 3.150 M08 2M08-157-S063T 0.571 5/8 0.335 1.575 3.937 M08 2M08-255-S063T 0.571 5/8 0.335 2.559 4.921 M08 2M08-315-S075T 0.571 3/4 0.335 3.150 5.906 M08 2M08-433-S100T 0.571 1 0.335 4.331 7.480 M08 2M10-118-S075S 0.689 3/4 0.413 1.181 3.937 M10 2M10-196-S075T 0.689 3/4 0.413 1.969 4.724 M10 2M10-275-S075T 0.689 3/4 0.413 2.756 5.512 M10 2M10-354-S100T 0.689 1 0.413 3.543 6.693 M10 2M10-433-S100T 0.689 1 0.413 4.331 7.480 M10 2M10-511-S125T 0.689 1 1/4 0.413 5.118 8.661 M10 2M12-118-S100S 0.906 1 0.492 1.181 4.331 M12 2M12-196-S100T 0.906 1 0.492 1.969 5.118 M12 2M12-275-S100T 0.906 1 0.492 2.756 5.906 M12 2M12-354-S100T 0.906 1 0.492 3.543 6.693 M12 2M12-433-S125T 0.906 1 1/4 0.492 4.331 7.874 M12 2M12-689-S150T 0.906 1 1/2 0.492 6.890 11.811 M12 2M16-137-S125S 1.142 1 1/4 0.669 1.378 4.921 M16 2M16-216-S125T 1.142 1 1/4 0.669 2.165 5.709 M16 2M16-315-S125T 1.142 1 1/4 0.669 3.150 6.693 M16 2M16-472-S125T 1.142 1 1/4 0.669 4.724 8.268 M16 2M16-689-S150T 1.142 1 1/2 0.669 6.890 11.811 M16 2

MATA (Steel Shank type)

(inch)

• S : Straight Neck Adapter• T : Taper Neck Adapter


50th Anniversary

Fig. 1 Fig. 2

Designation ØD Ød Ød1 L M Fig.MATA M08-315-S063S-C 0.571 5/8 0.335 3.150 5.906 M08 1

M08-433-S063S-C 0.571 5/8 0.335 4.331 7.087 M08 1M08-590-S063S-C 0.571 5/8 0.335 5.906 9.843 M08 1M08-394-S063S-C-590 0.571 5/8 0.335 0.394 5.906 M08 2M08-394-S063S-C-708 0.571 5/8 0.335 0.394 7.087 M08 2M08-394-S063S-C-984 0.571 5/8 0.335 0.394 9.843 M08 2M10-354-S075S-C 0.689 3/4 0.413 3.543 6.693 M10 1M10-433-S075S-C 0.689 3/4 0.413 4.331 7.874 M10 1M10-689-S075S-C 0.689 3/4 0.413 6.890 11.811 M10 1M10-394-S075S-C-669 0.689 3/4 0.413 0.394 6.693 M10 2M10-394-S075S-C-787 0.689 3/4 0.413 0.394 7.874 M10 2M10-394-S075S-C-1181 0.689 3/4 0.413 0.394 11.811 M10 2M12-354-S100S-C 0.906 1 0.492 3.543 6.693 M12 1M12-433-S100S-C 0.906 1 0.492 4.331 7.874 M12 1M12-689-S100S-C 0.906 1 0.492 6.890 11.811 M12 1M12-059-S100S-C-669 0.906 1 0.492 0.591 6.693 M12 2M12-059-S100S-C-787 0.906 1 0.492 0.591 7.874 M12 2M12-059-S100S-C-1181 0.906 1 0.492 0.591 11.811 M12 2M16-354-S125S-C 1.142 1 1/4 0.669 3.543 7.087 M16 1M16-472-S125S-C 1.142 1 1/4 0.669 4.824 8.268 M16 1M16-689-S125S-C 1.142 1 1/4 0.669 6.890 11.811 M16 1M16-078-S125S-C-708 1.142 1 1/4 0.669 0.787 70.87 M16 2M16-078-S125S-C-826 1.142 1 1/4 0.669 0.787 8.268 M16 2M16-078-S125S-C-1181 1.142 1 1/4 0.669 0.787 11.811 M16 2

MATA-C (Carbide Shank type)

(inch)


50th Anniversary

Designation ØD ØD1 ØD2 ØD3 Ød1 1 2 L MBT30 MAT-M06-053 0.433 0.461 0.512 1.181 0.256 0.197 0.827 2.087 06

MAT-M08-057 0.571 0.618 0.689 1.378 0.335 0.276 0.984 2.244 08MAT-M10-062 0.709 0.776 0.945 1.496 0.413 0.276 1.181 2.441 10MAT-M12-067 0.906 0.972 1.083 1.614 0.492 0.394 1.378 2.638 12MAT-M16-067 1.142 1.248 1.319 1.614 0.669 0.394 1.378 2.638 16

BT40 MAT-M06-062 0.433 0.461 0.551 1.575 0.256 0.197 0.984 2.441 08MAT-M06-077 0.433 0.461 0.551 1.575 0.256 0.197 1.575 3.031 06MAT-M06-092 0.433 0.461 0.551 1.575 0.256 0.197 2.165 3.622 06MAT-M08-067 0.571 0.618 0.748 1.732 0.335 0.276 1.181 2.638 08MAT-M08-082 0.571 0.618 0.748 1.732 0.335 0.276 1.772 3.228 08MAT-M08-097 0.571 0.618 0.748 1.732 0.335 0.276 2.362 3.819 08MAT-M10-072 0.709 0.776 0.906 1.969 0.413 0.394 1.378 2.835 10MAT-M10-087 0.709 0.776 0.906 1.969 0.413 0.394 1.969 3.425 10MAT-M10-102 0.709 0.776 0.906 1.969 0.413 0.394 2.559 4.016 10MAT-M12-077 0.906 0.972 1.181 2.165 0.492 0.394 1.575 3.031 12MAT-M12-092 0.906 0.972 1.181 2.165 0.492 0.512 2.165 3.622 12MAT-M12-107 0.906 0.972 1.181 2.165 0.492 0.512 2.756 4.213 12MAT-M16-077 1.142 1.248 1.457 2.165 0.669 0.512 1.575 3.031 16MAT-M16-092 1.142 1.248 1.457 2.165 0.669 0.512 2.165 3.622 16MAT-M16-107 1.142 1.248 1.457 2.165 0.669 0.512 2.756 4.213 16

BT50 MAT-M06-083 0.433 0.461 0.591 1.575 0.256 0.197 1.378 3.268 06MAT-M06-098 0.433 0.461 0.591 1.575 0.256 0.197 1.969 3.858 06MAT-M06-113 0.433 0.461 0.591 1.575 0.256 0.197 2.559 4.449 06MAT-M08-088 0.571 0.618 0.787 1.772 0.335 0.276 1.575 3.465 08MAT-M08-103 0.571 0.618 0.787 1.772 0.335 0.276 2.165 4.055 08MAT-M08-118 0.571 0.618 0.787 1.772 0.335 0.276 2.756 4.646 08MAT-M10-093 0.709 0.776 0.984 2.165 0.413 0.394 1.772 3.661 10MAT-M10-113 0.709 0.776 0.984 2.165 0.413 0.394 2.559 4.449 10MAT-M10-128 0.709 0.776 0.984 2.165 0.413 0.394 3.150 5.039 10MAT-M12-103 0.906 0.972 1.299 2.559 0.492 0.394 2.165 4.055 12MAT-M12-118 0.906 0.972 1.299 2.559 0.492 0.512 2.756 4.646 12MAT-M12-133 0.906 0.972 1.299 2.559 0.492 0.512 3.346 5.236 12MAT-M16-103 1.142 1.248 1.614 3.346 0.669 0.512 2.165 4.055 16MAT-M16-118 1.142 1.248 1.614 3.346 0.669 0.512 2.756 4.646 16MAT-M16-133 1.142 1.248 1.614 3.346 0.669 0.512 3.346 5.236 16

BT30 / BT40 / BT50

(inch)


50th Anniversary

Designation ØD ØD1 ØD2 ØD3 Ød1 1 2 L MHSK63A MAT-M06-061 0.433 0.461 1.063 1.575 0.256 0.197 0.984 2.402 06

MAT-M06-076 0.433 0.461 1.063 1.575 0.256 0.197 1.575 2.992 06MAT-M06-091 0.433 0.461 1.063 1.575 0.256 0.197 2.165 3.583 06MAT-M08-066 0.571 0.618 1.201 1.732 0.335 0.276 1.181 2.598 08MAT-M08-081 0.571 0.618 1.201 1.732 0.335 0.276 1.772 3.189 08MAT-M08-096 0.571 0.618 1.201 1.732 0.335 0.276 2.362 3.780 08MAT-M10-071 0.709 0.776 1.339 1.969 0.413 0.394 1.378 2.795 10MAT-M10-086 0.709 0.776 1.339 1.969 0.413 0.394 1.969 3.386 10MAT-M10-101 0.709 0.776 1.339 1.969 0.413 0.394 2.559 3.976 10MAT-M12-076 0.906 0.972 1.437 2.165 0.492 0.394 1.575 2.992 12MAT-M12-091 0.906 0.972 1.437 2.165 0.492 0.512 2.165 3.583 12MAT-M12-106 0.906 0.972 1.437 2.165 0.492 0.512 2.756 4.173 12MAT-M16-076 1.142 1.248 1.516 2.165 0.669 0.512 1.575 2.992 16MAT-M16-091 1.142 1.248 1.516 2.165 0.669 0.512 2.165 3.583 16MAT-M16-106 1.142 1.248 1.516 2.165 0.669 0.512 2.756 4.173 16

HSK100A MAT-M06-074 0.433 0.461 0.591 1.575 0.256 0.197 1.378 2.913 06MAT-M06-089 0.433 0.461 0.591 1.575 0.256 0.197 1.969 3.504 06MAT-M06-104 0.433 0.461 0.591 1.575 0.256 0.197 2.559 4.094 06MAT-M08-079 0.571 0.618 0.787 1.772 0.335 0.276 1.575 3.110 08MAT-M08-094 0.571 0.618 0.787 1.772 0.335 0.276 2.165 3.701 08MAT-M08-109 0.571 0.618 0.787 1.772 0.335 0.276 2.756 4.291 08MAT-M10-084 0.709 0.776 0.984 2.165 0.413 0.394 1.772 3.307 10MAT-M10-104 0.709 0.776 0.984 2.165 0.413 0.394 2.559 4.094 10MAT-M10-119 0.709 0.776 0.984 2.165 0.413 0.394 3.150 4.685 10MAT-M12-094 0.906 0.972 1.299 2.559 0.492 0.394 2.165 3.701 12MAT-M12-109 0.906 0.972 1.299 2.559 0.492 0.512 2.756 4.291 12MAT-M12-124 0.906 0.972 1.299 2.559 0.492 0.512 3.346 4.882 12MAT-M16-094 1.142 1.248 1.614 3.346 0.669 0.512 2.165 3.701 16MAT-M16-109 1.142 1.248 1.614 3.346 0.669 0.512 2.756 4.291 16MAT-M16-124 1.142 1.248 1.614 3.346 0.669 0.512 3.346 4.882 16

HSK63A / HSK100A

(inch)


50th Anniversary

[ Shank Type ]

-

Pro-L Mill

PAL

Tool typeS: Shank

S

UnitM : MetricA : Inch

A

HandR : RightL : LeftM : Multi edge

R

Coolant typeUnmarked : None

H : Thru-hole

H

Tool Dia.200 : Ø2

200

Tool Length.S : Standard type M : Middle type L : Long type

S

Shank Dia.200 : Ø2

200

No. of tooth3 : 3 teeth

3

[ Cutter Type ]

C

Tool typeC: Cutter

H

Coolant typeH : Thru-holeUnmarked : No Thru-hole

PAL

Pro-L Mill UnitM : MetricA : Inchl

A

Tool Dia.250 : Ø2.5

250 R

Chip breakerR : RightL : LeftM : Multi edge

Code System

Improved perpendicularity and lower cutting resistance resulting from the composition of the clearance face and High Helix edge

Improved productivity due to more than twice depth of cut compared to Pro-A and Pro-X Mill Strong clamping design by use of double screw on system design

Improved chip flow produced from coolant delivered by the helical type design of the chip pocket

Pro-L Mill

Features

New Indexable Milling Tool for High Quality Machining

Through coolant system Long tool life

2 Screw On System Strong clamping

High helix cutting edge application Decreased cutting resistance

Set of various Nose-R


50th Anniversary

Facing Shouldering Slotting Ramping Hellcal Cutting


Multi functional machining

Workpiece Cutting conditions

AI6061 (HRC30) vc(sfm) = 1640, fz(inch/t) = 0.007, ap(inch) = 1.18~2.36,ae(inch) = 0.039~0.197, z = 3

(inch)

Applications Chip breaker Cutting edge Features

Aluminum MAApplication of the edge optimized for Aluminum machining and buffed finish ensure excellent machining quality

Hard-to-cut material ML

Design of Low cutting resistance Chip Breaker ensures excellent machining quality for light cutting and Hard-to-cut material

Category M (STS) N (Non-feerous metal-AI) S (HRSA)

Grade PC5300 / PC5400 H01 PC5300 / PC5400

MA - -

ML -

Chip Breaker Features

Selection of Grade and Chip Breaker

Cutting Performance


50th Anniversary


Coated Uncoated Dimensions (inch)

Geometries

NCM

325

NCM

335

PC35

00PC

3545

PC95

30PC

6510

PC53

00PC

5400

PD20

00ST

30A

G10

H01 l d t r d1

LXET 250404PEFR-125-MA 0.984 0.424 0.187 1/64 0.1772504PEFR-125-MA 0.984 0.424 0.187 2/64 0.177250412PEFR-125-MA 0.984 0.424 0.187 3/64 0.177250416PEFR-125-MA 0.984 0.424 0.187 4/64 0.177250404PEFR-150-MA 0.984 0.418 0.187 1/64 0.1772504PEFR-150-MA 0.984 0.418 0.187 2/64 0.177250412PEFR-150-MA 0.984 0.418 0.187 3/64 0.177250416PEFR-150-MA 0.984 0.418 0.187 4/64 0.177340504PEFR-200-MA 1.339 0.542 0.219 1/64 0.2193405PEFR-200-MA 1.339 0.542 0.219 2/64 0.219340512PEFR-200-MA 1.339 0.542 0.219 3/64 0.219340516PEFR-200-MA 1.339 0.542 0.219 4/64 0.219340504PEFR-250-MA 1.339 0.543 0.219 1/64 0.2193405PEFR-250-MA 1.339 0.543 0.219 2/64 0.219340512PEFR-250-MA 1.339 0.543 0.219 3/64 0.219340516PEFR-250-MA 1.339 0.543 0.219 4/64 0.219

LXET 250404PEER-125-ML 0.984 0.424 0.187 1/64 0.1772504PEER-125-ML 0.984 0.424 0.187 2/64 0.177250412PEER-125-ML 0.984 0.424 0.187 3/64 0.177250416PEER-125-ML 0.984 0.424 0.187 4/64 0.177250404PEER-150-ML 0.984 0.418 0.187 1/64 0.1772504PEER-150-ML 0.984 0.418 0.187 2/64 0.177250412PEER-150-ML 0.984 0.418 0.187 3/64 0.177250416PEER-150-ML 0.984 0.418 0.187 4/64 0.177340504PEER-200-ML 1.339 0.542 0.219 1/64 0.2193405PEER-200-ML 1.339 0.542 0.219 2/64 0.219340512PEER-200-ML 1.339 0.542 0.219 3/64 0.219340516PEER-200-ML 1.339 0.542 0.219 4/64 0.219340504PEER-250-ML 1.339 0.543 0.219 1/64 0.219340508PEER-250-ML 1.339 0.543 0.219 2/64 0.219340512PEER-250-ML 1.339 0.543 0.219 3/64 0.219340516PEER-250-ML 1.339 0.543 0.219 4/64 0.219

Inserts

Pro-L Mill

DesignationTool

diameterØD

apRamping Blind hole helical cutting

Maximumangle (α˚) Lmin Max. Dia

ØDHmaxMax. pitch

dmaxMin. DiaØDHmin

MAX. pitchdmax

PALSA125HR-□□□□ 1.25 0.984 1.22 37.087 2.441 0.05 60 0.043PALSA150HR-□□□□ 1.5 0.984 0.88 51.142 3.071 0.05 76 0.043PALSA200HR-□□□□ 2 1.339 0.85 80.039 3.858 0.06 96 0.051PALSA250HR-□□□□ 2.5 1.339 0.64 105.71 4.882 0.06 122 0.051


Lmin = (inch)

Pro-L Mill Ramping & Helical Cutting Technical Data

(inch)


50th Anniversary

(inch)

Designation ØD ØD2 Ød Ød1 Ød3 a b E F ap lbs

PALCA 250HR 4 2.5 1.77 0.75 0.413 - 0.314 0.22 0.787 1.75 1.339 0.57

PALCA

: Stock item

Available Inserts


Ø2.50 FTGA0511-P TS20-100

Parts

AA 0°

• AR : 16°• RR : -8°


CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PD54

00

ST30

A

G10

H01

LXET 340504PEFR-250-MA3405PEFR-250-MA340512PEFR-250-MA340516PEFR-250-MA340504PEER-250-ML340508PEER-250-ML340512PEER-250-ML340516PEER-250-ML

LXET-MA LXET-ML


50th Anniversary

(inch)

Designation ØD Ød ℓ L ap lbsPALSA 125HR-2S100 2 1.25 1.00 1.969 5.512 0.984 1.09

125HR-2S125 2 1.25 1.25 1.969 5.512 0.984 1.54150HR-2S125 2 1.50 1.25 1.969 5.512 0.984 1.73150HR-2S150 2 1.50 1.50 1.969 5.512 0.984 2.27200HR-3S125 3 2.00 1.25 2.756 6.299 1.339 2.43200HR-3S150 3 2.00 1.50 2.756 6.299 1.339 2.97250HR-4S125 4 2.50 1.25 2.756 6.299 1.339 3.32250HR-4S150 4 2.50 1.50 2.756 6.299 1.339 3.86

PALSA (Single Edge)

SpecificationScrew Wrench Wrench

Ø1.25 FTKA0408TW15S

-Ø1.50 FTKA0410 -Ø2.00 FTGA0510-P -

TW20-100Ø2.50 FTGA0511-P -

Parts

Type Designation

Coated Uncoate

NCM3

25NC

M335

PC35

00PC

3600

PC35

45PC

9530

PC65

10PC

5300

PD54

00ST

30A

G10

H01

Ø1.2

5


Ø1.5

0


Type Designation

Coated Uncoate

NCM3

25NC

M335

PC35

00PC

3600

PC35

45PC

9530

PC65

10PC

5300

PD54

00ST

30A

G10

H01

Ø2.0

0


Ø2.5

0


: Stock item

Available Inserts

AA 0°

• AR : 12°~16°• RR : -5°~-8°

LXET-MA LXET-ML

Pro-L Mill


50th Anniversary

(inch)

Designation ØD Ød ℓ L ap lbsPALSA 250HM-4S125 12 2.5 1.25 5.118 8.661 3.78 4.97

250HM-4S150 12 2.5 1.50 5.118 8.661 3.78 5.51

PALSA (Multi Edge)

: Stock item

Available Inserts


Ø2.50 FTGA0511-P TS20-100

Parts

AA 0°

• AR : 16°• RR : ~-8°


CN20

00

CN30

NCM3

25

NCM3

35

PC35

00

PC36

00

PC35

45

PC95

30

PC65

10

PC53

00

PD54

00

ST30

A

G10

H01


LXET-MA LXET-ML

Head OfficeHolystar B/D, 1350, Nambusunhwan-ro, Geumcheon-gu, Seoul, 08536, KoreaTel : +82-2-522-3181 Fax : +82-2-522-3184Web : www. korloy.com E-mail : [email protected]

Cheongju Factory55, Sandan-ro, Heungdeok-gu, Cheongju-si, Chungcheongbuk-do, 28589, Korea Tel : +82-43-262-0141 Fax : +82-43-262-0146

Jincheon Factory54, Gwanghyewonsandan 2-gil, Gwanghyewon-myeon, Jincheon-gun, Chungcheongbuk-do, 27807, KoreaTel : +82-43-535-0141 Fax : +82-43-535-0144

R & D Institute Cheongju55, Sandan-ro, Heungdeok-gu, Cheongju-si, Chungcheongbuk-do, 28589, Korea Tel : +82-43-262-0141 Fax : +82-43-262-0711

R & D Institute SeoulHolystar B/D, 1350, Nambusunhwan-ro, Geumcheon-gu, Seoul, 08536, KoreaTel : +82-2-522-3181 Fax : +82-2-522-3184

620 Maple Avenue, Torrance, CA 90503, USATel : +1-310-782-3800 Toll Free : +1-888-711-0001 Fax : +1-310-782-3885www.korloyamerica.com E-mail : [email protected]

Gablonzer Str. 25-27, 61440 Oberursel, GermanyTel : +49-6171-277-83-0 Fax : +49-6171-277-83-59www.korloyeurope.com E-mail : [email protected]

Plot NO.415, Sector 8, IMT Manesar, Gurgaon 122051, Haryana, INDIATel : +91-124-4391790 Fax : +91-124-4050032www.korloyindia.com E-mail : [email protected]

Av. Aruana 280, conj.12, WLC, Alphaville, Barueri, CEP06460-010, SP, BrasilTel : +55-11-4193-3810E-mail : [email protected]

Ground Dongjing Road 56 District Free Trade Zone. Qingdao, ChinaTel : +86-532-86959880 Fax : +86-532-86760651E-mail : [email protected]

TN44-EI-0120160820

Documents

Milling Tool Series for Aluminum Pro - A / X / L Mill Series Technew… · · 2016-11-14Milling Tool Series for Aluminum Pro-A Mill ... increases accuracy to the degree of solid