MIO-5373 3.5” MI/O-Compact SBC, 8th Gen. Intel® Core™ U ...MIO-5373 Startup Manual 5 Figure 1: MIO-5373 Connector Locations (Top Side) Figure 2: MIO-5373 Connector Locations (Bottom

MIO-5373 Startup Manual 1

Before you begin installing your board, please make sure that the following items have been shipped:• 1 x MIO-5373 SBC• 1 x Startup Manual (P/N: 2046537300)• 1 x SATA Cable 30cm (P/N: 1700006291)• 1 x SATA Power Cable 35cm (P/N: 1700018785)• 1 x Audio JACK*3 Cable 20cm (P/N: 1700019584)• 1 x COM RS-232 Cable 20cm (P/N: 1700030404-01) • 1 x MIO-5373 Heatsink for 0 ~ 60°C

(P/N: 1960091427N001)• 1 x Mini Jumper (P/N: 9689000002)

If any of these items are missing or damaged, please con-tact your distributor or sales representative immediately.

Note1: For detailed contents of MIO-5373, please refer to information on the support website: http://sup-port.advantech.com.tw/

Note2: AdobeReaderisrequiredtoviewanyPDFfile.Adobe Reader can be downloaded at: http://get.adobe.com/tw/reader/otherversions/ (Adobe is the trademark of Adobe Systems Incorporated)

MIO-5373 3.5” MI/O-Compact SBC, 8th Gen. Intel® Core™ U-series (i7/i5/i3/Celeron®), DDR4, eMMC, HDMI, DP, 48-bit LVDS, 2 GbE, M.2 B-key 2280, DC-in 12-24V, iManager Startup Manual

General• CPU:

- Intel® Core™ i7-8665UE (Quad-Core, 1.70GHz) - Intel® Core™ i5-8365UE (Quad-Core, 1.60GHz) - Intel® Core™ i3-8145UE (Dual-Core, 2.20GHz)

• System Memory: Dual Channel/SODIMM DDR4-2400MT/s, up to 32GB

• BIOS: AMI EFI 256Mbit• Watchdog Timer: 65536 level, 0~65535 sec• TPM 2.0• iManager 3.0: Yes• Expansion Interface:

- M.2: 1 x M.2 E-key 2230 1 x M.2 B-key 2280 (SATA or NVMe PCIex2), 3042 LTE module (support USB2.0 only), optional M-key 2280 NVMe PCIex4. - MI/O Extension connector: 4 PCIex1, 1 PCIex4, USB2.0, LPC, SMBus, Line-out, 12V/5V Power supply

• Battery: Lithium 3V/ 210mAH• Audio:SupportsHighDefinitionAudio(HD),line-in,line-

out, Mic-in

Display• Controller: Intel® WHL-U SoC integrated, HDMI display

output ALC-888S for 48-bit LVDS display output• Maximum Resolution:

LCD: - LVDS Dual Channel 48-bit up to 1920 x 1200 - Option eDP1.4 up to 4096x2304@60Hz HDMI/DP: - 1 Port HDMI1.4 up to 4096x2160@30/24Hz - 1 Port DP1.2 up to 4096x2306@60Hz

• Multiple Display: Triple simultaneous displays by 48-bit LVDS/eDP+HDMI+DP

Ethernet Interface• Speed: 10/100/1000 Mbps• Controller: GbE1 - Intel i219, GbE2 - Intel i210-AT• Connector: RJ45 x2

Specifications Packing List

For more information on this and other Advantech products, please visit our website at:

http://www.advantech.com

http://www.advantech.com/eplatform

For technical support and service, please visit our support website at:

http://support.advantech.com.tw/

This manual is for MIO-5373.

Part No. 2046537300Printed in China

1st EditionFebruary 2020

2 MIO-5373 Startup Manual

I/O• Internal I/O: 2 x SATA 6Gb/s, 2 x USB2.0, 1 x

RS232/422/485, 16-bit GPIO, Inverter, SMBus, I2C*, HD Audio, LVDS, System FAN

• Rear I/O: 4 x USB3.1, HDMI, DP, 2 x RJ-45, 1 x RS232/422/485, 1 x DC-Jack(*optional)

• MI/O Expansion: 4 PCIex1, 1 PCIex4, USB2.0, LPC, SMBus, Line-out, 12V/5V Power supply

• Power Connector Type: Default support 2 x 2 pin ATX power connector, DC Jack is supported by request

Mechanical and Environmental• Dimensions (L x W): 146 x 102 mm (5.7 x 4 inches)• Power Supply Type: ACPI support for ATX only• Power Requirement: Vin: 12V-24V +/- 10%• Power Consumption:

- Max: i7-8665UE: 61.9 W (12V) i7-8665UE: 66.15W (24V) i5-8365UE: TBD i3-8145UE: TBD - Typical: Idle mode in Windows 10 i7-8665UE: 7.42 W (12V) i7-8665UE: 6.61 W (24V) i5-8365UE: TBD i3-8145UE: TBD

• Operating Temperature: 0~60°C (32~140°F)• Weight: 0.67 kg (reference weight of total package)

Jumpers and ConnectorsThe board has a number of connectors and jumpers that allowyoutoconfigureyoursystemtosuityourapplication.The table below lists the function of each of the jumpers and connectors.

Jumpers

Label Function

J1 AT/ATX mode selection

J2 RI# 5V/12V selection pin for CN9

J3 Panel Voltage Selection

J4 LVDS JEIDA and VESA mode Selection

SW1 Clear CMOS

Connector

Lable Function

CN1 DDR4 SODIMM 260P/H5.2mm

CN2 DDR4 SODIMM 260P/H9.2mm

CN3 DC input Connector

CN5 RTC Battery Connector

CN8 Power/LED/Case Open/Buzzer Connector

CN9 COM port Connector (RS232+RS422+RS485)

CN10 COM port Connector (RS232+RS422+RS485)

CN11 RJ45 Connector (2 port)

CN12 Inverter Connector

CN13 LVDS Connector

CN14 eDP Connector

CN15 HDMI and DP++ Connector

CN16 Key E Connector

CN17 Key B and Key M(option) Connector

CN20 SIM card Connector

CN22 USB3.1 Connector (2 ports)

CN23 USB3.1 Connector (2 ports)

CN24 Internal USB Connector

CN25 HDD Power Connector

CN26 HDD Connector

CN27 HDD Connector

CN28 GPIO/RS232 Connector

CN29 Audio Connector

CN30 GPIO/RS232 Connector

CN30A1 MIOe Connector

CN31 I2C Bus Connector

CN32 System FAN Connector

CN35 CANBus Connector

CN36 SMBus Connector

CN37 DC input Connector (Adapter)

Specifications(Cont.) Jumpers and Connectors (Cont.)


J1: ATX/AT Mode Selection

Function Jumper Setting

AT Mode (Default)

ATX Mode

Pin SignalPinDefinition1 AT_DET#

2 GND

J2: RI# 5V/12V selection pin for CN9


COM(CN9) voltage setting: +V5

COM(CN9) voltage setting: +V12

Panel Voltage Setting: RI# (Default)

Pin SignalPinDefinition1 +V5

2 CN9_RI#

3 COM_RI#

4 CN9_RI#

5 +V12

6 CN9_RI#

J3: Panel Voltage Selection


Panel Voltage Setting:+V3.3(Defualt)

Panel Voltage Setting:+V5

Panel Voltage Setting: +V12

Pin SignalPinDefinition1 +V3.3

2 NC

3 +V_CH7511B_LCD

4 +V12

5 +V5

6 NC

Jumpers and Connectors (Cont.)


J4: LVDS JEIDA and VESA mode Selection


JEIDA mode Setting:+V3.3

VESA mode Setting: GND (Default)

Pin SignalPinDefinition1 LVDS1_VCON

2 LVDS1_VCC

3 GND

4 NC

SW1: Clear CMOS


Keep COMS Data (Default)

Clear CMOS Date

Pin SignalPinDefinition1 RTC_a_RST#

2 RTC_RST#

3 GND

Caution! The computer is provided with a battery-powered real-time clock circuit. There is a danger of explo-sion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries ac-cording to manufacturer’s instructions.

Jumpers and Connectors (Cont.) Caution


Figure 1: MIO-5373 Connector Locations (Top Side)

Figure 2: MIO-5373 Connector Locations (Bottom Side)

Figure 3: MIO-5373 Connector Locations (Coastline)

Connector Locations

CN8

CN11CN23

CN29

CN15CN9

CN2

CN27 CN12

CN1

CN13

CN22 CN32CN37

CN31CN36

CN24

CN10

CN30CN28

CN30

CN26CN25J1

CN3

J2 J3

J4

CN30A1

CN17CN16CN14 CN5

CN20


Mechanical Drawing

Figure 4: MIO-5373 Mechanical Drawing (Top Side)

Figure 5: MIO-5373 Mechanical Drawing (Bottom Side)

Figure 6: MIO-5373 Mechanical Drawing (Coastline)

H

G

F

E

D

C

B

A

1 5432

8 1110976

APPEARANCEPART

INTERIORPART

FILE NAME

P/N ADDED CODE

MODEL NAME

0.20

D

0.20

P10.05

2019/10/3

2019/10/3

REV.

SIZEUNITS mm SHEET2 Of 3 A2

APPROVED

DESIGNER

CHECKED

DRAWER

SCALE

PART NO.D

THIRD ANGLEPROJECTION

0.250.300.40

0.60D=3L/1000

0.50

0.20

FINISHING

MATERIAL

(Max)

S2S1M2

0.10

0.40

L0.700.40

0.15

0.25

0.20

0.300.25

0.500.801.0

0.50 0.35 0.601.10

0.250.300.45

0.200.10 0.15M1

DIMENSIONALTOLERANCES

0.10

0.150.15

0.300.20

ANGLE

6~29.9930~79.99

80~179.99180~314.99

315~800

0.050~5.99

90

Other 1.5

0.601.00

P2

0.150.10

0.400.50

DESCRIPTION/PART NAME

2019/10/3

TOLERANCES

H

G

F

E

D

654321


Figure 7: MIO-5373 Mechanical Drawing (with Heatsink)

1. There is a Heatsink in the white box, please take it and remove the release paper from the thermal pads.

2. There are eight screws, six studs and two nuts inside the white box, please install the heatsink into place as per illustration and assembly sequence below:

1 5 3

4 2 6

Mechanical Drawing (Cont.)

Quick Installation Guide

Remove Release Paper

Documents

MIO-5373 3.5” MI/O-Compact SBC, 8th Gen. Intel® Core™ U ...MIO-5373 Startup Manual 5 Figure 1: MIO-5373 Connector Locations (Top Side) Figure 2: MIO-5373 Connector Locations (Bottom