Mod. 8.3/5 Rev. 0 del 14/12/2016 MB-PSOC M10€¦ · Port . Tel. 06 7827464 / Fax. 06 7806894 P.IVA 10190271006 Via Rocca di Papa, 21 - 00179 Roma 171122UM MB-PSOC_M10 User’s Manual

Tel. 06 7827464 / Fax. 06 7806894

P.IVA 10190271006 Via Rocca di Papa, 21 - 00179 Roma

MB-PSOC_M10 User’s Manual

Code Revision Page

171122UM A 1 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016

The information contained in this document is proprietary to GEB Enterprise S.r.l. This document and the information contained herein may not be copied, reproduced, used or disclosed in whole or in part in any form without the prior written consent of GEB Enterprise S.r.l.

© Copyright GEB Enterprise S.r.l. - All Rights Reserved

MB-PSOC_M10

USER’S MANUAL

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 2 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



DOCUMENT REVISION HISTORY

Rev. Date Description

A 23/01/2017 First Release

Emission Date

23/01/2017 Resp. PRG

Resp. RSQ

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 3 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



INDEX

USER’S MANUAL -------------------------------------------------------------------------------------------------------------------------------------- 1

1. INTRODUCTION -------------------------------------------------------------------------------------------------------------------------------- 4

1.1. TECHNICAL FEATURES ----------------------------------------------------------------------------------------------------------------- 4

2. SAFETY MEASURES ---------------------------------------------------------------------------------------------------------------------------- 5

2.1. POWER SUPPLY AND WORKING TEMPERATURES ------------------------------------------------------------------------------ 5

3. BLOCK DIAGRAM ------------------------------------------------------------------------------------------------------------------------------ 6

4. I/O CONNECTIONS ---------------------------------------------------------------------------------------------------------------------------- 7

4.1. J3 CONNECTOR ----------------------------------------------------------------------------------------------------------------------------- 7 4.2. J4 CONNECTOR ----------------------------------------------------------------------------------------------------------------------------- 9

5. QUICK START---------------------------------------------------------------------------------------------------------------------------------- 11

INDEX of FIGUREs

FIGURE 1: MB-PSOC_M10 BOARD TOP VIEW. -------------------------------------------------------------------------------------------------------- 4 FIGURE 2: BLOCK DIAGRAM OF THE MB-PSOC_M10 BOARD. --------------------------------------------------------------------------------------- 6 FIGURE 3: J3 CONNECTOR. ------------------------------------------------------------------------------------------------------------------------------- 7 FIGURE 4: J4 CONNECTOR. ------------------------------------------------------------------------------------------------------------------------------- 9 FIGURE 5: MB PSOC CONNECTION ------------------------------------------------------------------------------------------------------------------- 11 FIGURE 6: MB SUPPLY CONNECTORS ----------------------------------------------------------------------------------------------------------------- 11 FIGURE 7: MB ALTERA CONNECTORS ----------------------------------------------------------------------------------------------------------------- 12 FIGURE 8: MB ALTERA SERIAL CONNECTORS --------------------------------------------------------------------------------------------------------- 12 FIGURE 9: SERIAL PORT SCREEN MENU --------------------------------------------------------------------------------------------------------------- 13

INDEX of TABLEs

TABLE 1: VOLTAGE LEVELS AND WORKING TEMPERATURES. -------------------------------------------------------------------------------------------- 5 TABLE 2: J3 CONNECTOR SPECIFIC SIGNALS DESCRIPTION. ---------------------------------------------------------------------------------------------- 7 TABLE 3: J3 CONNECTOR PINS FUNCTION AND MAPPING. ---------------------------------------------------------------------------------------------- 8 TABLE 4: J3 CONNECTOR BUTTONS AND LED. ---------------------------------------------------------------------------------------------------------- 8 TABLE 5: J4 CONNECTOR SPECIFIC SIGNALS DESCRIPTION. ---------------------------------------------------------------------------------------------- 9 TABLE 6: J4 CONNECTOR PIN FUNCTION AND MAPPING. --------------------------------------------------------------------------------------------- 10 TABLE 7: J4 CONNECTOR UARTS ---------------------------------------------------------------------------------------------------------------------- 10 TABLE 8: SERIAL CONFIGURATION --------------------------------------------------------------------------------------------------------------------- 13

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 4 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



1. Introduction

The MB-PSOC_M10 is a Mother-Board for the pSOC-M10-08 boards designate for teaching and development applications.

Figure 1: MB-PSOC_M10 board top view.

1.1. TECHNICAL FEATURES

The MB-PSOC_M10 Board provide the following features:

1. On Board 3.3V Voltage regulator (from 5V up to 12V) 2. N°2 Serial port through FTDI USB or RS232 DB9 3. N°1 Altera Bite Blaster Port 4. N°4 Leds accessible from pSOC 5. N°4 Buttons accessible from pSOC 6. N°1 trimmer for ADC applications.

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 5 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



1.2. POWER SUPPLY AND WORKING TEMPERATURES

The following table reports power supply and temperature values of the MB-PSOC_M10 board:

Power supply 5V up to 12V @10W (from USB or Power Jack)

Max 3V3 Current 3A ( pSoc consumption max 0.6A)

Operating Temperature Range 0°C/+70°C Commercial Temp. Range, -40°C/+85°C Industrial Temp. Range

Storage Temperature Range -40/+150°C

Table 1: Voltage levels and working temperatures.

To supply the Board can use the USB Connector (5V) or the Power Jack (up to 12V), If you want to supply external Device From Header 3.3V it’s Highly recommended to use 10W Supplier.

1.3. SAFETY MEASURES

WARNING! The Board contain sensitive electrostatic charges components, handle with caution.

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 6 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



2. BLOCK DIAGRAM

The following figure shows the block diagram of the MB-PSOC_M10 board:

Figure 2: Block diagram of the MB-PSOC_M10 board.

PSOC

J4

Hea

de

r

J3

Hea

de

r

FTDI USB or RS232

FTDI USB or RS232

4 LEDS 4

BUTTONS 3V3

Regulator

Altera BiteBlaster

Port

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 7 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



3. I/O CONNECTIONS

The MB-PSOC_M10 development board provides two general purpose I/O connectors with the same pin of pSoc Connectors (1:1)

3.1. J3 connector

Figure 3 shows the J3 connector with pin numbers and signals:

Figure 3: J3 connector.

As it can be seen, 24 general purpose I/O pins are provided on the J3 connector. Moreover, a POWER signal and 6 further specific signals are provided. These signals are described in Table 2:

Signal name Description

TDO,TDI,TMS,TCK JTAG Signals

CONFIG# JTAG Enable signal (LOW)

PFAIL Power Fail signal

Table 2: J3 connector specific signals description.

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 8 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



The following table shows the mapping between the FPGA pin locations and the J3 connector pins number and function:

Function PIN FPGA Pin number Pin number PIN FPGA Function

+3V3 - 1 2 - +3V3

IO_0 7 3 4 8 IO_1

TDO 20 5 6 16 TMS

TCK 18 7 8 19 TDI

CONFIG# 129 9 10 27 PFAIL

I_CKI_3 28 11 12 17 IO_2

IO_3 10 13 14 11 IO_4

IO_5 13 15 16 14 IO_6

IO_7 30 17 18 33 IO_CKO_1

IO_CKO_0 32 19 20 45 IO_8

IO_9 48 21 22 47 IO_10

IO_11 50 23 24 52 IO_12

IO_13 54 25 26 55 IO_14

IO_15 57 27 28 58 IO_16

IO_17 59 29 30 60 IO_18

IO_19 62 31 32 64 IO_20

GND - 33 34 - GND

Table 3: J3 connector pins function and mapping.

The Signals in Red are used for Buttons and Leds and Trimmer, see the following table:

Signal name Pin FPGA

LED[0..3] 52, 54, 55 and 57

Switches[0..3] 45, 48, 47 and 50

Trimmer 7

Table 4: J3 connector Buttons and LED.

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 9 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



3.2. J4 connector

Figure 4 shows the J4 connector with pin numbers and signals:

Figure 4: J4 connector.

As shown in the figure above, in addition to 26 general purpose I/O signals and 8 further specific signals are provided. These signals are described in Table 5:

Signal name Description

AD_xx SPI Interface Signals

POR_n Reset Signal (Active LOW)

TXD1, RXD1 RS232 Interface Signals

Table 5: J4 connector specific signals description.

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 10 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



Table 6 shows the mapping between the FPGA pin locations and the J4 connector pins number and function:

Function PIN FPGA Pin number Pin number PIN FPGA Function

TXD1 - 1 2 - RXD1

IO_40 111 3 4 121 POR_n

IO_39 110 5 6 93 AD_SCLK

IO_CKO_2 91 7 8 106 AD_DIN

IO_38 101 9 10 105 AD_DOUT

IO_37 99 11 12 100 AD_CS_V#

IO_36 92 13 14 97 AD_CS_I#

I_CKI_4 29 15 16 87 IO_35

I_CKI_6 89 17 18 88 IO_CKI_5

IO_34 86 19 20 90 IO_CKI_7

IO_41 126 21 22 85 IO_33

IO_31 81 23 24 84 IO_32

IO_29 78 25 26 80 IO_30

IO_27 76 27 28 79 IO_28

IO_25 74 29 30 77 IO_26

IO_23 69 31 32 75 IO_24

IO_21 65 33 34 66 IO_22

Table 6: J4 connector pin function and mapping.

The Signals in Red are used for the two Serial Port, see the following table:

Signal name Pin FPGA

UART1 (TX RX) 75 and 74

UART2 (TX RX) 77 and 76

Table 7: J4 connector UARTs

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 11 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



4. Quick Start

This Section Describe how to Supply the Board, Program the pSoc and use the serial Port for communicate with pSoc NIOS II system (in this case use the 171212A1 MB-pSOC_M10 NIOS II demo system).

Follow this procedure:

1. Insert the pSoc Board on J1 and J2 Connectors

Figure 5: MB pSOC Connection

2. For Supply the Board use or the USB Connectors or Power Jack and use PS1 to switch ON

Figure 6: MB Supply Connectors

USB1 USB2

Power Jack

PS1

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 12 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



3. Connect the Altera Bite Blaster and program the pSoc Board with the system .pof

Figure 7: MB Altera Connectors

4. The Leds Start to Blink with a specific Pattern 5. Use the Jumper for choose the preferred serial Comunication (USB or RS232) of the two

UART (Remember to Close only the jumper of chosen communication)

Figure 8: MB Altera Serial Connectors

Altera Connector

Close this for RS232 DB9

Close this for USB

Close this for RS232 DB9

Close this for USB

Tel. 06 7827464 / Fax. 06 7806894



Code Revision Page

171122UM A 13 of 13

Mod. 8.3/5 Rev. 0 del 14/12/2016



6. Open a Serial terminal on PC (like Teraterm) and Connect to the Two Serial Port with the following configuration

Name Value

Baud Rate 57600

Data 8 Bit

Parity None

Stop 1 Bit

Flow Control None

Table 8: Serial Configuration

7. Reset the pSoc with the Reset Button (S1 of pSoc), in the Terminal will be printed the command menu of the demo system.

Figure 9: Serial Port Screen Menu

Documents

Mod. 8.3/5 Rev. 0 del 14/12/2016 MB-PSOC M10€¦ · Port . Tel. 06 7827464 / Fax. 06 7806894 P.IVA 10190271006 Via Rocca di Papa, 21 - 00179 Roma 171122UM MB-PSOC_M10 User’s Manual