MOD Standard 05-69

8/18/2019 MOD Standard 05-69

1/40

Ministry of Defence

Defence Standard 05-69

Issue 3 Publication Date 10 November 2000

Standard Colour Scheme of

Metallic Materials for Aerospace

Applications

8/18/2019 MOD Standard 05-69

2/40

DEF STAN 05-69/3

AMENDMENT RECORD

Amd No Date Text Affected Signature and Date

REVISION NOTE

This standard is raised to Issue 3 to update its content and make the content of the annexes

more directly applicable to the RAF stores vocabularies 30A to 30E. An associated electronic

version of the database containing colour codes for a wider range of metallic materials has

also been produced.

HISTORICAL RECORD

This standard supersedes the following:

Defence Standard (Def Stan) 05-69 Issue 2 dated 12 April 1996

Defence Standard (Def Stan) 05-69 Issue 1 dated 21 May 1993

QTR 7/AQD Issue1 dated May 1978

http://www.dstan.mod.uk/data/05/069/colours.mdbhttp://www.dstan.mod.uk/data/05/069/colours.mdb

8/18/2019 MOD Standard 05-69

3/40

DEF STAN 05-69/3

1

CONTENT

Description Page

Content 1Preface 2

Main Text 3

SECTION 1 GENERAL REQUIREMENTS

0 Introduction 3

1 Scope 3

2 Warning 4

3 Related Documents 4

4 Description 4

SECTION 2 REQUIREMENTS OF A COLOUR CODE SCHEME

5 Colour code 5

6 Contractual Requirements 5

7 Eyesight 5

8 Overall Marking 5

SECTION 3 APPLICATION OF A COLOUR CODE SCHEME

9 Alloy, Product and Delivery Conditions 610 Products not to be Colour Coded 7

11 Reversal of Colour Code 7

12 Colours 8

13 Application of Colour Code Markings 8

14 Application for New or Unlisted Colour Codes 10

Table 1 Colour Shades for Use in Colour Code Marking 8

Annexes Contents and Notes 11

Annex A Colour Codes in Order of Standard 13

Annex B Colour Codes in Order of Colour 31

8/18/2019 MOD Standard 05-69

4/40

DEF STAN 05-69/3

2

PREFACE

Standards for Defence

STANDARD COLOUR SCHEME OF METALLIC MATERIELS

FOR AEROSPACE APPLICATIONS

a. This standard sets out a scheme for the colour code identification of metallic

materials intended for aerospace applications.

b. This standard has been produced on behalf of the Standardization Advisory Group

(SAG) by the Defence Logistics Organisation (NPPO(Air), Commodity Acquisition), which

represents Tri-Service interests in this matter.

c. This standard has been agreed by the authorities concerned with its use and is

intended to be used whenever relevant in all future designs, contracts, orders etc. and

whenever practicable by amendment to those already in existence. If any difficulty arises

which prevents application of the Defence Standard, the Directorate of Standardization

(DStan) shall be informed so that a remedy may be sought.

d. Any enquiries regarding this standard in relation to an invitation to tender or a

contract in which it is incorporated are to be addressed to the responsible technical or

supervising authority named in the invitation to tender or contract.

e. Compliance with this Defence Standard shall not in itself relieve any person from

any legal obligations imposed upon them.

f. This standard has been devised solely for the use of the Ministry of Defence (MOD)

and its contractors in the execution of contracts for the MOD. To the extent permitted by

law, the MOD hereby excludes all liability whatsoever and howsoever arising (including,

but without limitation, liability resulting from negligence) for any loss or damage however

caused when the standard is used for any other purpose.

8/18/2019 MOD Standard 05-69

5/40

DEF STAN 05-69/3

3

TEXT

Standards for Defence

STANDARD COLOUR SCHEME OF METALLIC MATERIELS

FOR AEROSPACE APPLICATIONS


0 INTRODUCTION

0.1 This colour scheme was devised for the colour code identification of those metallic

materials in RAF stores vocabulary sections 30A, 30B and 30E, which are intended for

aerospace application and are supplied to Service units or establishments directly or through

the Royal Air Force Storage Depot. It also includes non-aerospace metallic materials in RAF

stores vocabulary sections 30C and 30D.

0.2 Although intended primarily for direct Government contracts for metallic materials,

the scheme may also be used as a secondary means of identification by Contractors at their

own works.

0.3 This standard does not override any requirement for overall identification by ink or other marking on the product, or use of a durable label when required by the relevant material

or technical standard. Colour coding shall be used in the absence of any other method of

marking or when called up by the contract.

1 SCOPE

1.1 This standard sets out a standard scheme for the colour code identification of

metallic materials intended for aerospace applications.

1.2 The colour codes listed in Annexes A and B are appropriate to the contents of the

RAF stores vocabulary sections 30A to 30E inclusive. Codes for similar standards andalloys are included as well as codes for, principally, the AECMA aerospace aluminium

alloy and steel standards and alloys which are potential replacements for the British

Standards ‘L’, ‘S’ and ‘T’ series and which are likely to be used on new designs.

1.3 Colour codes do not reflect the issue status of any standard.

8/18/2019 MOD Standard 05-69

6/40

DEF STAN 05-69/3

4


2 WARNING

The Ministry of Defence (MOD), like its contractors, is subject to both United Kingdom

and European laws regarding Health and Safety at Work, without exemption. All DefenceStandards either directly or indirectly invoke the use of processes and procedures that could

be injurious to health if adequate precautions are not taken. Defence Standards or their use

in no way absolves users from complying with statutory and legal requirements relating to

Health and Safety at Work.

3 RELATED DOCUMENTS

3.1 The publications shown below are referred to in the text of this standard. Publications

are grouped and listed in alpha numeric order.

Designation Title

BS 381C Specification for Colours for Identification, Coding and Special

Purposes

BS 3488 Specification for Technical Anhydrous Lanolin

Def Stan 03-2 Cleaning and Preparation of Metal Surfaces

Def Stan 80-54 Paint, Finishing, General Service Gloss Types: Brushing, Spraying

3.2 Reference in this standard to any related document means in any invitation to tender

or contract the edition and all amendments current at the date of such tender or contract

unless a specific edition is indicated.

3.3 In consideration of 3.2 above, users shall be fully aware of the issue and amendment

status of all related documents, particularly when forming part of an invitation to tender or

contract. Responsibility for the correct application of standards rests with users.

3.4 DStan can advise regarding where related documents are obtained from. Requests for

such information can be made to the DStan Helpdesk. How to contact the helpdesk is

shown on the outside rear cover of Def Stans.

3.5 It was not considered practical to include in 3.1 a full list of the document numbers

and titles of those standards referenced in the annexes.

4 DESCRIPTION

The colour code scheme is a means of rapid identification of material, additional to the

requirements of the material specification or technical standard, and shall not be used as the

sole means of identification.

8/18/2019 MOD Standard 05-69

7/40

DEF STAN 05-69/3

5

SECTION 2 REQUIREMENTS OF A COLOUR CODE SCHEME

5 COLOUR CODE

The supplier and user shall ensure that only one colour code scheme is used and that it

complies with the requirements of this standard.

6 CONTRACTUAL REQUIREMENTS

6.1 The criteria for deciding whether or not an item (i.e. sheet, bar, tube, rod) as issued to

user units, requires to be colour coded individually, and hence supplied to the RAF

similarly marked, depends on the Denomination of Quantity (D of Q). It is therefore

important that the supplier delivers goods identified in the correct manner. Goods not

supplied in accordance with the contract shall not be accepted.

6.2 Except as allowed by 6.1 and 13.3, every piece of material ordered for use by Service

units or establishments shall be individually colour code marked in accordance with thisstandard, even though the material may have been bundled and given a bulk final

identification by the manufacturer.

7 EYESIGHT

Many people are lacking colour discrimination and users of this standard shall therefore

ensure that only those with eyesight free from this defect are directly concerned with the

identification of colour coded materials.

8 OVERALL MARKING

Overall marking by a suitable printing process giving the specification and condition is

preferred to colour coding. When overall marking is used it shall comply with the

requirements of the material standard. Overall marking shall only be used when the surface

condition is receptive to the printing and if such marking is durable under normal storage

conditions. In order to permit re-marking of material with particulars of the specification

and condition after re-heat treatment, ink shall be of a type which is obliterated by heat and

which does not etch the surface.

8/18/2019 MOD Standard 05-69

8/40

DEF STAN 05-69/3

6


9 ALLOY, PRODUCT AND DELIVERY CONDITIONS

9.1 Alloy type

The alloy provides distinguishing features by virtue of its density or colour, i.e.:

a. Light alloys - aluminium, magnesium and titanium alloys;

b. Heavy alloys - steel or nickel and cobalt and their alloys (also some cupro-

nickel alloys of a silver-grey colour);

c. Copper and its alloys (as they are usually distinctively coloured materials in

themselves).

Different alloys in a similar product form may, therefore, be given the same colour code, e.g.

the following sheet products are colour coded “brown”:

aluminium alloy BS L166 (Clad 2014A-F)steel BS EN 3526 * (FE-PM1505 Annealed)copper alloy BS EN 1652: CW004A/H065

* NOTE: May only be available as an AECMA Prestandard (prEN) at the time of

publication of this standard. AECMA prENs are valid documents, accepted as being

technically finalised and usable in contracts, when published on green paper.

9.2 Product form

The product form also provides a distinguishing feature, i.e. bar type products (e.g. rolled bar or section, including rectangular bar), flat products (e.g. plate, sheet or strip), tube or

wire.

Different product forms of the same alloy or alloy type may, therefore, be given the same

colour code, e.g. the following are colour coded “black-yellow-blue”:

aluminium alloy bar - BS EN 2632 (AL-P7075-T73511)*aluminium alloy sheet - BS EN 485 (EN AW-1200-H16)aluminium alloy tube - BS EN 2073 (AL-P1050A-H14) *aluminium alloy wire - BS EN 1301 (EN AW-3103-F)

* See note to 9.1.

8/18/2019 MOD Standard 05-69

9/40

DEF STAN 05-69/3

7


9.3 Delivery condition

Certain materials differing only in surface condition or intended usage and, which are in the

same metallurgical delivery condition and have the same mechanical properties, are giventhe same colour code, e.g. the following are colour coded “green-red-yellow”:

BS S82B - Black Bars for Machining (Softened)

BS S82D - Bright Bars for Machining (Softened)

Materials with the same specification number but different metallurgical delivery condition,

hence different mechanical properties have different colour codes, e.g.

BS S535 Chromium - molybdenum steel sheet (Softened) is colour coded “green-

brown-green” but:

BS S535 Chromium - molybdenum steel sheet (Hardened and tempered) is colour coded brown-blue-yellow”.

10 PRODUCTS NOT TO BE COLOUR CODED

10.1 Forging stock, forgings and castings

Colour codes are not allocated to forgings, forging stock or to castings in this standard.

10.2 Tool steel, filler rods, electrodes, welding rod and solder

Due to the form and varying packaging quantities of these materials, colour coding is notrequired. Materials supplied under these headings are to be identified by their respective

NATO stock number (NSN) using an appropriate method such as tagging.

10.3 Expanded Metal, Perforated Sheet, Gauze and Honeycomb

Due to the form of these materials colour coding is not required. Materials provided in

these forms are to be identified by their respective NATO stock number (NSN) using an

appropriate method such as tagging.

11 REVERSAL OF COLOUR CODE

Colour codes shall be selected such that any one code shall not be confused with its reverse

order counterpart, i.e. for colour code “green-red-yellow” the reverse order “yellow-red-

green” shall not be permitted as a code.

8/18/2019 MOD Standard 05-69

10/40

DEF STAN 05-69/3

8


12 COLOURS

12.1 The colours black, blue, brown, green, red, white and yellow are used. These colours

are given the numerical values 1 to 7 shown in Table 1. The numerical code aids presentation in the annexes.

12.2 In order that colour marking shall be as permanent as possible, especially where

material has to be stocked in the open, the use of paint to specification Def Stan 80-54 is

recommended. The most distinct shades, which have been selected, are given in Table 1.

Table 1: Colour Shades for Use in Colour Code Marking

COLOUR CODE* BS 381C

SHADENO. DESCRIPTION

Black

Blue

Brown

Green

Red

White

Yellow

1

2

3

4

5

6

7

N/A

104

320

221

537

N/A

355

N/A

Blue Azure

Light Brown

Brilliant Green

Signal Red

N/A

Lemon Yellow

NOTE1: * Code used in annexes

13 APPLICATION OF COLOUR CODE MARKINGS

13.1 Before painting the colour code temporary protectives shall be removed from the area

of application using solvents complying with Def Stan 03-2.

13.2 Materials shall be marked, with the first colour painted on the outside edge/end/corner

as follows:

13.2.1 Bars and tubes

Each bar and tube shall be painted at both ends with the stipulated colour or colours in the

following widths:

a. For one colour - 1 band 200 mm wide

b. For two colours - 2 bands each 100 mm wide

c. For three colours - 3 bands each 75 mm wide

8/18/2019 MOD Standard 05-69

11/40

DEF STAN 05-69/3

9


13.2.1 (Continued)

d. For four colours - 4 bands each 50 mm wide

e. For five colours - 5 bands each 35 mm wide

13.2.2 Plate, sheet and strip

One of the following methods is to be used:

a. A band or bands of the required colours are to be painted on each plate, sheet

or strip diagonally across one corner. The corner which bears identification

stamp marks shall be selected if that is the means by which the material is

identified. The width of the band or bands shall be in accordance with 13.2.1

and painting is to commence 150 mm from the corner measured at right

angles to the length of the band. Sheets and strips less than 300 mm wide

shall be painted at one end in a similar manner to bars. Identification stampmarks shall not be obscured.

b. Alternatively, each plate sheet or strip shall be painted with a disc. For a

single colour the disc shall be 75 mm in diameter, additional colours, when

required, shall be applied in concentric rings 35 mm wide.

c. For large-scale production of plate, sheet and flat strip, the product may be

stacked and then slid endwise, so that 35-40 mm of the end of each product is

exposed (in addition to the whole surface of the top plate, sheet or strip).

Bands of paint of the same length as the width required by 13.2.1 shall then

be painted on the products in one operation, resulting in an identification

mark on each plate, sheet or strip. The colours shall be applied to the face of the plate, sheet or strip which bears the identification marks and preferably

adjacent to them, if that is the means by which the material is identified.

d. Laminated shim material

e. Due to the manufactured form of this material, the appropriate colour code is

to be applied to one surface only. The colour coded surface is to be used for

reference for the whole sheet and it is therefore essential that the colour

coded surface is the last sheet to be used.

f. Wires and rods (as defined by the material specification) The required

colours shall be painted in bands on the side of each bundle and the outer

turns of each coil. The band or bands shall be at right angles to the wires or

rods and shall not be less than 75 mm total width, e.g. one band 75 mm wideor 3 bands 25 mm wide. The paint marks shall extend at least halfway round

the bundle of wires or rods at the selected part of the coil.

13.3 If the supplier wishes to use suitable coloured adhesive tape for identification, the

tapes shall be compatible with the material to be identified. When tape is used, it is

preferred that the complete code is contained on a single tape and each colour is not less

than 15 mm wide. Where individual tapes are to be used, their widths shall be:

8/18/2019 MOD Standard 05-69

12/40

DEF STAN 05-69/3

10


13.3 (Continued)

a. Single colour - 50 mm wide

b.

Two colours - 30 mm wide per colour c. Three colours - 25 mm wide per colour

d. Four colours - 20 mm wide per colour

e. Five colours - 15 mm wide per colour

For the identification of bar, section, tube, rod or wire, the adhesive tape shall go a

minimum of 1½ times around the individual piece or bundle as appropriate.

13.4 The bar, section, tube, etc may be required to be protected by a suitable preservative,

e.g lanolin complying with BS 3488, which shall not obscure the colour code. The

protective shall be removable by a solvent referenced in Def Stan 03-2.

Where it is a contractual requirement to apply colour code identification, the appropriate

colours shall be applied in the order given. The first colour shall be applied nearest that end

or corner of the material which bears the stamped identification, if that is the means by

which the material is identified.

14 APPLICATION FOR NEW OR UNLISTED COLOUR CODES

14.1 Application for new or unlisted codes shall be made to:

Defence Logistics Organisation

NPPO(Air)Commodity Acquisition

Palmer Pavilion

RAF Wyton

HUNTINGDON

Camb PE28 2EA

FAO: CA Metallic (Technical)

Tel: 01480 452451 ext 4888

Fax: 01480 446971

14.2 Application for an electronic version of the database associated with this standard shall

be made to the Directorate of Standardization (DStan).

http://www.dstan.mod.uk/data/05/069/colours.mdbhttp://www.dstan.mod.uk/data/05/069/colours.mdb

8/18/2019 MOD Standard 05-69

13/40

DEF STAN 05-69/3

11

SECTION 4 ANNEXES

CONTENTS OF ANNEXES AND NOTES

Annex A Colour Codes in order of Standard

Annex A Page

AMS xxxx series 13

BS ‘B’ series 15

BS EN 485 15

BS EN 75x series 15

BS EN 1xxx series 15

BS EN 2xxx AECMA aerospace series (see Note 1) 16

BS EN 3xxx AECMA aerospace series (see Note 1) 20

BS EN 4xxx AECMA aerospace series (see Note 1) 22BS EN 10xxx series 23



BS ‘HR’ series 26

BS ‘L’ series 26

BS ‘S’ series 27

BS ‘T’ series 27

BS ‘TA’ series 28

BS 970-3 28

BS 1xxx series 28

BS 2871-2, 4109, 6323-4 29

DTD series 29

MAM series 29

MIL series 29

Annex B Colour Codes in order of Colour 31

NOTES

1 Some of the BS EN 2XXX, 3XXX and 4XXX series may only be available

as an AECMA Prestandard (prEN) at the time of publication of this standard.AECMA prENs are valid documents, accepted as being technically finalised and

usable in contracts, when published on green paper. Those listed in this standard are

potential replacements, singly or in conjunction with other(s), for current BS ‘HR’,

‘L’, ‘S’, ‘T’ and ‘TA’ series standards.

2 The abbreviations used in the annexes are generally those designations

used in the relevant material standards. This particularly applies to those used to

describe ‘Temper’. However, in a number of instances, especially for materials in

the BS EN 10xxx series of steel standards, the designation relates to the specified

delivery condition and not to the normal understanding of ‘temper’. Other

abbreviations should be self-evident.

8/18/2019 MOD Standard 05-69

14/40

DEF STAN 05-69/3

ANNEX A Colour Codes In Order Of Standard

Colours:

1 - Black; 2 - Blue; 3 - Brown; 4 - Green; 5 - Red; 6- White; 7 - Yellow

12

Standard Alloy Temper Description Colour

AMS 4001 1100 O Aluminium sheet 67676

AMS 4003 1100 H14 Aluminium sheet 75757AMS 4006 3003 O Aluminium alloy sheet 65156

AMS 4008 3003 H14 Aluminium alloy sheet 71617

AMS 4015 5052 O Al-MgCr plate, sheet 75357

AMS 4025 6061 O Al-mGSiCuCr plate, sheet 75257

AMS 4026 6061 T4 Al-MgSiCuCr plate, sheet 75457

AMS 4027 6061 T6 Al-MgSiCuCr plate, sheet 74747

AMS 4029 2014A W Al-MgSiCuCr plate 72727

AMS 4029 2014A W51 Al-MgSiCuCr plate 72627

AMS 4029 2014A T651 Al-MgSiCuCr plate 73137

AMS 4035 2024 O Al-CuMgMn plate, sheet 74647

AMS 4037 2024 T3 Al-CuMgMn plate, sheet 74547

AMS 4040 Clad 2024 O Clad Al-CuMgMn plate, sheet 4347

AMS 4041 Clad 2024 T3 Clad Al-CuMgMn plate, sheet 74247

AMS 4044 7075 O Al-ZnMgCuCr plate, sheet 74147

AMS 4045 7075 T6 Al-ZnMgCuCr plate, sheet 73737

AMS 4045 7075 T651 Al-ZnMgCuCr plate sheet 73637AMS 4048 Clad 7075 O Clad Al-ZnMgCuCr plate, sheet 73537

AMS 4049 Clad 7075 T6 Clad Al-ZnMgCuCr plate, sheet 73437

AMS 4051 Clad 7178 O Clad Al-ZnMgCuCr plate, sheet 73237

AMS 4071 5052 O Aluminium alloy hydraulic tubing 5416

AMS 4153 2014A T6 Aluminium alloy bar, section 64646

AMS 4182 1100 F Aluminium wire 7147

AMS 4901 CP-1[CP-1B] Annealed Pure titanium sheet [485 MPa] 1341

AMS 4900 CP-2(CP-1C) Annealed Pure titanium sheet [379 MPa] 1427

AMS 4902 CP-3 [CP-1A] Annealed Pure titanium sheet [276 MPa] 546

AMS 4908 Ti-Mn Annealed Titanium-manganese alloy sheet; 110ksi yield stress 1432

AMS 4911 Ti-6Al-4V Annealed Titanium alloy sheet, strip and plate. 4315

Non-metric version of MAM 4911

AMS 5510 Type 321 Softened Corrosion resisting [stainless] steel plate, sheet, strip 75457

AMS 5512 Type 347 Softened Corrosion resisting [stainless] steel sheet, strip, plate 23132

AMS 5517 Type 301 ¼ hard Corrosion resisting [stainless] steel sheet, strip, plate. 76167

AMS 5518 Type 301 ½ hard Corrosion resisting [stainless] steel sheet, strip, plate. 76267

AMS 5519 Type 301 Hard Corrosion resisting [stainless] steel sheet, strip, plate. 76367

AMS 5528 17-7PH Softened Corrosion resisting steel plate, sheet, strip 32323

AMS 5528 17-7PH TH1050 Corrosion resisting steel plate, sheet, strip 32123

AMS 5529 17-7PH Softened Corrosion resisting steel plate, sheet, strip. Strength specified

by contract. Cold rolled solution treated/Annealed 32423

AMS 5529 17-7PH Cold worked Corrosion resisting steel plate, sheet, strip. Strength specified

by contract 32523

AMS 5532 N-155 Solution treated Corrosion/heat resisting steel plate, sheet 76567

AMS 5540 INCONEL 600 Annealed Nickel base heat resisting alloy sheet, strip, plate 35653

AMS 5542 X-750 Fully hard Nickel base heat resisting alloy plate, sheet, strip 62126

AMS 5556 Type 347 Softened Corrosion resisting steel tubing 2136

AMS 5571 Type 347 Softened Corrosion resisting steel tube 2653AMS 5572 25Cr-20Ni - Seamless corrosion resisting steel/heat resisting steel tube 62426

AMS 5628 SAE 51430 Hard+Temp 16Cr-2.5Ni bar, section 64346

AMS 5628 SAE 51430 Softened 16Cr-2.5Ni bar, section 7 2327

AMS 5643 17-4PH Softened Precipitation hardening stainless steel bar 64146

AMS 5646 Type 347 Softened Corrosion resisting steel bar, section 76367

AMS 5872 Nickel alloy Solution treated Nickel alloy sheet 26262

AMS 5901 301 Softened Corrosion resisting steel type 301 plate, sheet, strip 76467

AMS 5902 301 ¾ hard Corrosion resisting steel type 301 plate, sheet, strip 76767

8/18/2019 MOD Standard 05-69

15/40

DEF STAN 05-69/3


Colours:

1 - Black; 2 - Blue; 3 - Brown; 4 - Green; 5 - Red; 6 -White; 7 - Yellow

13


AMS 6345 4130 Normalised Steel plate, sheet, strip 67176

AMS 6350 4130 Annealed Steel plate, sheet, strip 67276

AMS 6350 4130 Annealed (M) Steel plate, sheet, strip Annealed (Modified) 67376AMS 6350 4130 Normalised Steel plate, sheet, strip 75757

AMS 6360 4130 Normalised Steel tubing, normalised. 57675

AMS 6361 4130 Cold worked Steel tubing. 57475

AMS 6362 4130 Hard+Temp Steel tubing. HT150 condition 57375

AMS 6415 4340 Hard+Temp Steel bar, section 13731

AMS 6415 4340 Normalised Steel bar, section 13231

AMS 6415 4340 Softened Steel bar, section 13631

AMS (MIL)-T-6736 4130 Annealed Steel tube; A condition 65256

AMS (MIL)-T-6736 4130 Cold worked Steel tube: cold drawn 56365

AMS (MIL)-T-6736 4130 Hard+Temp Steel tube; HT125 condition 63436

AMS (MIL)-T-6736 4130 Hard+Temp Steel tube: HT150 condition 61516

AMS (MIL)-T-6736 4130 Hard+Temp Steel tube: HT180 condition. 67676

AMS (MIL)-T-6736 4130 Normalised Steel tube; N condition 64546

AMS-QQ-A-200/3 2024 T351 Aluminium alloy 2024 bar, section, rod, tube, wire. 62326

AMS-QQ-A-200/8 6061 T6511 Aluminium alloy 6061 bar, rod, section, tube, wire 3545

AMS-QQ-A-225/6 2024 T351 Aluminium alloy 2024 bar, rod, wire. 61516

AMS-QQ-A-225/9 7075 T7351 Aluminium alloy 7075 bar, rod, special section, wire. 67176

AMS-QQ-A-250/1 1100 H14 Pure aluminium plate, sheet 75657

AMS-QQ-A-250/1 1100 H19 Pure aluminium plate, sheet 75157

AMS-QQ-A-250/3 Clad 2014A T4/T42 Clad aluminium alloy sheet 31513

AMS-QQ-A-250/3 Clad 2014A T6/T62 Clad aluminium alloy sheet 26462

AMS-QQ-A-250/4 2024 O Al-CuMgMn plate, sheet 65656

AMS-QQ-A-250/4 2024 T3 Al-CuMgMn plate, sheet 64346


AMS-QQ-A-250/4 2024 T4 Al-CuMgMn sheet, plate 71317

AMS-QQ-A-250/5 Clad 2024 O Clad Al-CuMgMn plate sheet 76467

AMS-QQ-A-250/5 Clad 2024 T3 Clad Al-CuMgMn sheet, strip 76767AMS-QQ-A-250/5 Clad 2024 T351 Clad Al-CuMgMn plate, sheet 62626

AMS-QQ-A-250/7 5086 H32 Al-MgMnCr plate, sheet 76267

AMS-QQ-A-250/8 5052 H22/H24 Al-MgCr plate, sheet 76367

AMS-QQ-A-250/8 5052 O Al-MgCr plate, sheet 76567

AMS-QQ-A-250/11 6061 O Al-MgSiCuCr plate, sheet 63136

AMS-QQ-A-250/11 6061 T6 Al-MgSiCuCr plate, sheet 67376

AMS-QQ-A-250/11 6061 T4 Al-MgSiCuCr plate, sheet 65356

AMS-QQ-A-250/12 7075 O Al-ZnMgCuCr plate, sheet 62326

AMS-QQ-A-250/12 7075 T6 Al-ZnMgCuCr plate, sheet 62426

AMS-QQ-A-250/12 7075 T651 Al-ZnMgCuCr plate, sheet 62526

AMS-QQ-A-250/13 Clad 7075 O Clad Al-ZnMgCuCr plate, sheet 63536

AMS-QQ-A-250/13 Clad 7075 T6 Clad Al-ZnMgCuCr plate, sheet 63636


AMS-QQ-A-250/14 7178 O Al-ZnMgCuCr plate, sheet 64546


AMS-QQ-A-250/14 7178 T6 Al-ZnMgCuCr plate, sheet 64646AMS-QQ-A-250/14 7178 T651 Al-ZnMgCuCr plate, sheet 64746

AMS-QQ-A-250/15 Clad 7178 O Clad Al-ZnMgCuCr plate sheet 61516


AMS-QQ-A-250/15 Clad 7178 T651 Clad Al-ZnMgCuCr plate sheet 61716

AMS-QQ-A-430 1100 F Aluminium wire 7157

AMS-QQ-S-763 Type 440C Annealed Corrosion resisting steel bar, section 43434

AMS-S-6758 4130 A/B conditions Corrosion resisting steel bar; Hot worked 61616

AMS-S-6758 4130 C condition Corrosion resisting steel bar; Annealed 62126

AMS-S-6758 4130 F condition Corrosion resisting steel bar; Hardened & tempered 63236

8/18/2019 MOD Standard 05-69

16/40

DEF STAN 05-69/3


Colours:


14


AMS-S-7720 18-8 A condition Corrosion resisting steel bar, wire; Annealed 64646

AMS-S-7720 18-8 B condition Corrosion resisting steel bar, wire; Cold worked 62726

AMS-S-7720 18-8 C condition Corrosion resisting steel bar, wire; Hot worked 62326

BS B27 TUNGUM M Al-Ni-Si brass tube 515

BS B27 TUNGUM M Al-Ni-Si brass tube. Pressure tested to 465.5 bar 676

BS EN 485 EN AW-1050A H14 EN AW-Al99.5 O sheet 143

BS EN 485 EN AW-1050A H18 EN AW-Al99.5 H18.sheet 147

BS EN 485 EN AW-1050A O EN AW-Al99.5 O sheet 145

BS EN 485 EN AW-1080A F EN AW-Al99.8(A) F sheet 3273

BS EN 485 EN AW-1080A H14 EN AW-Al99.8(A) H14 sheet 325

BS EN 485 EN AW-1080A H18 EN AW-Al99.8(A) H18 sheet 123

BS EN 485 EN AW-1080A O EN AW-Al99.8(A) O sheet 327

BS EN 485 EN AW-1100 H19 EN AW-Al99.0Cu 5656

BS EN 485 EN AW-1200 F EN AW-Al99.0 F sheet 7127

BS EN 485 EN AW-1200 H12 EN AW-Al99.0 H12 sheet 173




BS EN 485 EN AW-1200 O EN AW-Al99.0 O sheet 12

BS EN 485 EN AW-2014A T4 EN AW-Al Cu4SiMg(A) T4 sheet 23

BS EN 485 EN AW-2014A T6 EN AW-AlCu4SiMg(A) sheet 2327

BS EN 485 EN AW-3103 F EN AW-Al Mn1 F sheet 2514

BS EN 485 EN AW-3103 H12 EN AW-Al Mn1 H12 sheet 214




BS EN 485 EN AW-3103 O EN AW-Al Mn1 O sheet 212

BS EN 485 EN AW-5083 F EN AW-Al Mg4.5Mn0.7 F sheet 4745

BS EN 485 EN AW-5083 H22/H32 EN AW-Al Mg4.5Mn0.7 H22/H32 sheet 737

BS EN 485 EN AW-5083 H24 EN AW-AlMg4.5Mn0.7 H24/H34 sheet 1737

BS EN 485 EN AW-5083 O EN AW-Al Mg4.5Mn0.7 O sheet 717

BS EN 485 EN AW-5154A O EN AW-Al Mg3.5(A) O sheet 247BS EN 485 EN AW-5154A H22/H32 EN AW-Al Mg3.5(A) H22/H32 sheet 243

BS EN 485 EN AW-5154A H24/H34 EN AW-Al Mg3.5(A) H24/H34 sheet 25

BS EN 485 EN AW-5251 F EN AW-Al Mg2 F sheet 3143

BS EN 485 EN AW-5251 H22 EN AW-AlMg2 H22/H32 sheet 3147

BS EN 485 EN AW-5251 H24/H34 EN AW-Al Mg2 H24/H34 sheet 3424

BS EN 485 EN AW-5251 O EN AW-Al Mg2 O sheet 314

BS EN 485 EN AW-6082 O EN AW-Al Si1MgMn O sheet 131

BS EN 485 EN AW-6082 T4 EN AW-Al Si1MgMn T4 sheet 132

BS EN 485 EN AW-6082 T6 EN AW-Al Si1MgMn T6 sheet 134

BS EN 754 EN AW-1050A F Alternative to BS EN 755 3614

BS EN 754 EN AW-5251 F Alternative to BS EN 755 3616

BS EN 755 EN AW-1050A F Extruded bar, etc.: Alternative is BS EN 754 [cold drawn] 145

BS EN 755 EN AW-5251 F Extruded bar, etc.: Alternative is BS EN 754 [cold drawn] 314

BS EN 1652 CW004A H040 Copper sheet. 467

BS EN 1652 CW004A H065 Electrolytic tough pitch copper sheet, ½ hard: 3

BS EN 1652 CW004A M Copper sheet 57

BS EN 1652 CW004A R200/H040 Copper sheet. Softened 125

BS EN 1652 CW004A R290/H090 Copper sheet. Hard 157


BS EN 1652 CW006A R240/H065 Copper sheet. ½ Hard 257




8/18/2019 MOD Standard 05-69

17/40

DEF STAN 05-69/3


Colours:


15



BS EN 1652 CW024A H040 Copper sheet. Softened 476

BS EN 1652 CW024A M Copper sheet 465



BS EN 1652 CW352H M Copper-nickel sheet. 2462

BS EN 1652 CW352H R300/H070 Copper-nickel sheet. Softened 2515

BS EN 1652 CW450K R610/H190 Phosphor Bronze sheet. Extra hard 162

BS EN 1652 CW451K R310/H075 Phosphor Bronze sheet. Softened 135

BS EN 1652 CW451K R400/H120 Phosphor Bronze sheet. ¼ hard 152

BS EN 1652 CW451K R490/H160 Phosphor Bronze sheet. ½ hard 273

BS EN 1652 CW451K R550/H180 Phosphor Bronze sheet. Hard 212

BS EN 1652 CW451K R630/H200 Phosphor Bronze sheet. Extra hard 326

BS EN 1652 CW452K M Phosphor bronze sheet. As rolled 56

BS EN 1652 CW452K R350/H080 Phosphor bronze sheet. Softened 354

BS EN 1652 CW452K R420/H125 Phosphor bronze sheet. ¼ hard 325

BS EN 1652 CW452K R500/H160 Phosphor bronze sheet. ½ hard 131

BS EN 1652 CW452K R640/H200 Phosphor bronze sheet. Hard 161

BS EN 1652 CW452K R720/H220 Phosphor bronze sheet. Extra hard 346

BS EN 1652 CW508L R300/H055 Brass sheet (37% Zn). Softened 7BS EN 1652 CW508L R350/H095 Brass sheet (37% Zn). ¼ hard 717

BS EN 1652 CW508L R410/H120 Brass sheet (37% Zn). ½ hard 5

BS EN 1652 CW508L R480/H150 Brass sheet (37% Zn). Hard 12

BS EN 1652 CW508L R550/H170 Brass sheet (37% Zn). Extra hard 373

BS EN 1652 CW612N R410/H120 Leaded brass sheet - ½ hard 57

BS EN 1652 CW612N R490/H150 Leaded brass sheet hard 2326

BS EN 1652 CW612N R560/H175 Leaded brass sheet – extra hard 2352

BS EN 1982 CC481K M Phosphor bronze, PB1 type/BS B8 type 134

BS EN 2072 AL-P1050A H14 Aluminium sheet, strip; 0.4

8/18/2019 MOD Standard 05-69

18/40

DEF STAN 05-69/3


Colours:


16


BS EN 2128 AL-P7075 T651 Al-ZnMgCuCr bar; 6

8/18/2019 MOD Standard 05-69

19/40

DEF STAN 05-69/3


Colours:


17


BS EN 2504 FE-PM1801 Hard+Temp Steel bar, 1130-1330 MPa; d

8/18/2019 MOD Standard 05-69

20/40

DEF STAN 05-69/3


Colours:


18


BS EN 2640 AL-P2017A T4 Bar,section with peripheral coarse grain control; 152

1

8/18/2019 MOD Standard 05-69

21/40

DEF STAN 05-69/3


Colours:


19


BS EN 2805 AL-P7475 T7651 Al-ZnMgCuCr plate; 6

8/18/2019 MOD Standard 05-69

22/40

DEF STAN 05-69/3


Colours:


20


BS EN 3461 TI-P99003 Annealed Titanium alloy bar; 540-740 MPa; d

8/18/2019 MOD Standard 05-69

23/40

DEF STAN 05-69/3


Colours:


21


BS EN 3679 FE-PM3902 Softened X7CrNiAl17-7 steel plate; 1240-1450 MPa; 6

8/18/2019 MOD Standard 05-69

24/40

DEF STAN 05-69/3


Colours:


22


BS EN 4293 AL-P7175 T73511 Al-ZnMgCuCr extruded bar, section; a/d

8/18/2019 MOD Standard 05-69

25/40

DEF STAN 05-69/3


Colours:


23


BS EN10083-1 NA* 150M19 QT } 13136

BS EN10083-1 NA* 605M36 QT } 13145

BS EN10083-1 NA* 605M36 U } Special steel black bar 2637

BS EN10083-1 NA* 817M40 QT } 13156

BS EN10083-1 NA* 817M40 U } 2714

* NA = National Annex

BS EN10083-2 C40 [1.0511] N } 14541

BS EN10083-2 C40 [1.0511] QT } Unalloyed steel black bar 16165

BS EN10083-2 C40 [1.0511] U } 16164

BS EN10084 C16E [1.1148] U Case hardening steel black bar 2657

BS EN10087 11SMn30 [1.0715] U } Free cutting steel black bar. 21217

BS EN10087 15SMn13 [1.0725] U } 3624

BS EN10088-2 1.4301 AT+2D Softened } Stainless steel sheet (Type 304) 2324

BS EN10088-2 1.4301 2H [CW] Cold rolled } 2325

BS EN10088-3 1.4301 1X As rolled } 41434BS EN10088-3 1.4301 AT + 2D Annealed } Stainless steel bar (Type 304 stainless steel) 57375

BS EN10088-3 1.4301 2H Cold worked } 34143

BS EN10111 DD11 [1.0332] Hot rolled } 24242

} Mild steel sheet for cold forming – descaled

BS EN10111 DD13 [1.0335] Hot rolled } General purpose finish 34143

}

BS EN10130 DC01 [1.0330] +A+m Cold rolled mild steel sheet for forming. 46464

General purpose finish

BS EN10130 DC01 [1.0330] +B+g Cold rolled mild steel sheet for forming. Fine finish 45654

BS EN10130 DC03 [1.0347] +A+m Cold rolled mild steel sheet for forming. 75657

General purpose finish

BS EN10130 DC03 [1.0347] +B+g Cold rolled mild steel sheet for forming. Fine finish 75357

BS EN10139 DC01 [1.0330] +C690+Am Mild steel narrow strip for cold forming. Hard 46464

BS EN10139 DC01 [1.0330] +AM+A Mild steel narrow strip for cold forming. Annealed 25652

BS EN10139 DC01 [1.0330] +LC Mild steel narrow strip for cold forming. Skin passed 25252

BS EN10139 DC01 [1.0330] +MA } 46764

BS EN10139 DC03 [1.0347] - } Mild steel narrow strip for cold forming. 32723

BS EN10139 DC04 [1.0338] - } 23232

BS EN10139 DC04 [1.0338] +C290 Mild steel narrow strip for cold forming. Approx ¼ hard 25352

BS EN10142 DX51D [1.0226] +Z600+NA+C Hot dip zinc coated mild steel sheet for cold forming.

600 g/m²; normal spangle, surface quality A; passivated 37673

BS EN10149-3 S355NC [1.0977] Normalised High yield strength steel sheet for cold forming. 75257

BS EN10203 T57-Bright-E5.6/5.6 Annealed Cold reduced electrolytic tinplate 37373

BS EN10210 S275J2H [1.0138] Hot finished Structural hollow section of non alloy and fine grain 65356

structural steel

BS EN10277-2 C40 [1.0511] +N+SL/SH Bright general engineering steel bar. Normalised 75657

BS EN10277-2 C40 [1.0511] U+C+SH/SL Bright general engineering steel bar. Cold drawn & turned 3125

or ground. NOT HEAT TREATED.

BS EN10277-2 C40 [1.0511] U+SH/SL Bright general engineering steel bar. Turned or ground 3124

NOT COLD DRAWN OR HEAT TREATED.

BS EN10277-3 11SMn30 +C+SL/SH Bright free cutting cold drawn steel bar 43734

BS EN10277-3 11SMn30 +SL/SH Bright free cutting steel bar NOT COLD DRAWN 45154

8/18/2019 MOD Standard 05-69

26/40

DEF STAN 05-69/3


Colours:


24


BS EN10277-3 15SMn13 [1.0725 ] U+C+SH/SL Bright free cutting steel bright bar, cold drawn & turned 3617

or ground.

BS EN10277-3 15SMn13 [1.0725] U+SH+SL Bright free cutting steel bright bar, turned or ground 3616

NOT COLD DRAWN

BS EN10277-5 C40E [1.1186] +N+C+SH/SL Bright steel bar for quenching and tempering. Normalised 5245

Cold drawn & turned or ground.

BS EN10277-5 C40E [1.1186] +QT+SH/SL Bright steel bar for quenching and tempering. Hardened and 3143

tempered. Turned or ground. NOT COLD DRAWN

BS EN10277-5 C40E [1.1186] QT+C+SH/SL Bright steel bar for quenching and tempering. Hardened and 3137

tempered. Cold drawn and turned or ground.

BS EN10277-5 C60E [1.1221] +N+SL/SH Bright steel bar for quenching and tempering. Normalised 51215

NOT COLD DRAWN

BS EN10277-5 34CrNiMo6 [1.6582] +QT+SL/SH Bright steel bar for quenching and tempering. Hardened and 45354

tempered. NOT COLD DRAWN

BS EN10305-2 E235+A U } 236

BS EN10305-2 E235+C - } Cold finished seamless steel tube. 3125

BS EN10305-2 E355+C - } 467

BS EN10305-2 E355+N N } 465

BS EN12163 CW006A R200 Pure copper rod. Annealed. 6

BS EN12163 CW024A M Pure copper rod 1614

BS EN12163 CW451K M Phosphor bronze rod 474

BS EN12163 CW712R M Naval brass rod 2

BS EN12163 CW712R M Naval brass rod 5

BS EN12164 CW612N M Free machining leaded brass rod 567

BS EN12164 CW612N R410/H120 Free machining leaded brass rod. ½H 57

BS EN12164 CW614N M Free machining leaded brass rod 1

BS EN12164 CW721R M High strength brass rod 1247

BS EN12164 CW721R R520 High strength brass rod. Hard 15

BS EN12166 CW024A H105 Pure copper wire - hard. 353

BS EN12166 CW024A M Pure copper wire 3243

BS EN12166 CW452K R340/H080 Phosphor bronze wire. Softened 4574BS EN12166 CW452K R510/H160 Phosphor bronze wire. ½ hard 4576

BS EN12166 CW452K R740/H215 Phosphor bronze wire. Hard 4617

BS EN12166 CW452K R900/H245 Phosphor bronze wire. Spring hard version 4626

BS EN12166 CW508L R550/H155 Brass wire. ½ hard/hard 535

BS EN12166 CW508L R280/H065 Brass wire. Soft 3625

BS EN12166 CW508L R700/H190 Brass wire Spring hard 3635

BS EN12166 CW612N M Leaded brass wire. 567

BS EN12166 CW612N R410/H120 Leaded brass wire. ½ hard 57

BS EN12166 CW614N M Leaded brass wire. 1

BS EN12167 CW024A M Pure copper profiles and rectangular bar. 1614

BS EN12167 CW612N M Leaded brass profiles and rectangular bar 567

BS EN12167 CW612N R410/H120 Leaded brass profiles and rectangular bar. ½ hard 57

BS EN12167 CW614N M Leaded brass profiles and rectangular bar. 1

BS EN12167 CW712R M Naval brass profiles and rectangular bar. 2

BS EN12167 CW721R R520 High strength brass profiles and rectangular bar. Hard 1351

BS EN12168 CW612N R410/H120 Leaded brass hollow rod. ½ hard 57

BS EN12168 CW614N M Leaded brass hollow rod 1

BS EN12449 CW024A H035 Pure copper tube. Not subject to special pressure test. Soft 13

BS EN12449 CW024A H035 Pure copper tube Subject to 70 bar pressure test. Soft 46

BS EN12449 CW024A M Pure copper tube 154

BS EN12449 CW024A R290/H090 Pure copper tube. ½ hard 427

BS EN12449 CW508L M Brass tube 1241

8/18/2019 MOD Standard 05-69

27/40

DEF STAN 05-69/3


Colours:

1 - Black; 2 - Blue; 3 - Brown; 4 - Green; 5 - Red; 6 -White; 7 - Yellow#

25


BS EN12449 CW508L R280/H065 Brass tube. Soft 1217

BS EN12449 CW508L R350/H085 Brass tube 1235

BS EN12451 CW352H R290/H080 Kunifer 10 tube 1434

BS EN12451 CW352H M Kunifer 10 tube. 565

BS EN12451 CW707R M Sea water resistant brass tube. 1245

Not subject to special

pressure test.

BS EN12451 CW707R M Sea water resistant brass tube. 616

Subject to 70 bar pressure test.

BS EN12451 CW707R H070 Sea water resistant brass tube. Soft 137

BS EN12451 CW707R R320/H080 Sea water resistant brass tube 1275

BS EN13601 CW004A M As drawn pure copper electrical wire. 375

BS EN13601 CW004A R200 Electrical pure copper wire - Annealed. 365

BS EN13602 CW004A M As drawn electrical pure copper wire. 364

BS EN13602 CW004A R200 Electrical drawn copper wire - Annealed. 363

BS HR203 NIMONIC 75 Annealed } 275BS HR206 NIMONIC 263 Annealed } Nickel base heat resisting alloy sheet, strip, plate 1571

BS HR208 INCONEL 600 Annealed } 1217

BS HR403 NIMONIC 75 Annealed Nickel base heat resisting alloy tube 1575

BS L 16 1200 H14/H24 Aluminium sheet. Half hard 2

BS L 17 1200 O Aluminium sheet Soft 1

BS L 34 1200 F 99% Aluminium bar, section 15

BS L 36 1050A F Aluminium rod & rivet wire 1

BS L 37 2014A H13 Aluminium alloy wire for rivets 515

BS L 44 5251 F Aluminium alloy extruded bar, section 424

BS L 44 5251 O Aluminium alloy extruded bar, section 46

BS L 54 1200 F 99%Aluminium tube 25

BS L 56 5251 O Al-2%Mg alloy tube 637

BS L 59 3103 H16/H26 Al-Mn sheet, strip; ¾ hard 152

BS L 60 3103 H12/H22 Al-Mn sheet,etc; ¼ hard 414

BS L 61 3103 O Al-Mn alloy sheet, strip 272BS L 63 2014A T6 Al-CuMgSiMn tube 515

BS L 80 5251 O Al-2.5%Mg sheet, strip 415

BS L 81 5251 H16/H26 Al-2.5%Mg sheet, strip 232

BS L 85 6066 T6 Al-CuSiMg bar,section:to BS L85 condition 4.2 272

BS L 85 6066 T651 Al-CuSiMg bar,section:to BS L85 condition 4.3 365

BS L105 2014A T3 Al-4.4CuMgSiMn tube 274

BS L113 6082 T652 Al-MgSiMn sheet, strip 167

BS L113 6082 O Al-MgSiMn sheet, strip 7167

BS L113 6082 W Al-MgSiMn sheet, strip 1671

BS L163 Clad2014A T3 Clad Al-CuMgSiMn sheet, strip 13

BS L164 Clad2014A F Clad Al-CuMgSiMn sheet, strip 2124





BS L166 Clad2014A F Clad Al-CuMgSiMn sheet, strip; close tolerance 4345

BS L166 Clad2014A T4 Clad Al-CuMgSiMn sheet, strip;close tolerance 4374




BS L168 2014A T6 Al-CuMgSiMn bar,section to BS L100 Section 2323

BS L168 2014A T6510 Al-CuMgSiMn bar,section to BS L100 Section 5 363




BS L504 ZW3 F Mg-3%ZnZr sheet, strip 56

8/18/2019 MOD Standard 05-69

28/40

DEF STAN 05-69/3


Colours:


26


BS S1 S1 - 35-45 ton carbon steel; bright bar 7

BS S 14 S14B - Carbon steel bars, case hardening 37

BS S 15 S15B&D - 3%Ni steel, case hardening; black bar [S15D-cold worked] 737

BS S 61 S61B&D Hard+Temp 35ton 12%Cr corrosion resisting steel black bar 375

BS S 62 S62B&D Hard+Temp 45/55ton,12%Cr corrosion resisting steel bar 717

BS S 80 S80B&D Hard+Temp 880-1080 MPa, high CrNi corrosion resisting steel bar 315

BS S 80 S80E Softened 880-1080 MPa, high CrNi corrosion resisting steel bar 15

BS S 82 S82B&D Softened 4.5%NiCrMo; >1320 MPa; case hardening steel bar 457

BS S 92 S92B&D Hard+Temp 40ton C-Mn steel bar for machining 16

BS S 93 S93B&D Normalised 35ton steel bar for machining 56

BS S 95 S95B&D Hard+Temp 55ton, 1.5%NiCrMo steel bar for machining 145

BS S 97 S97B&D Hard+Temp 65ton, 2.5%NiCrMo steel bar for machining 165

BS S 98 S98B&D Hard+Temp 75ton, 2.5%NiCrMo high C steel bar 232

BS S 99 S99B&D Softened 1230-1420 MPa, 2.5%NiCrMo,high C steel bar 243

BS S 99 S99E&G Hard+Temp 1230-1420 MPa, 2.5%NiCrMo high C steel 237

BS S114 S114B&D Hard+Temp 55ton MnMo steel bar [114D Hard+Temp+cold worked] 134

BS S117 S117B&D Hard+Temp 55ton 1%Cr steel bar 172

BS S130 S130B&D Hard+Temp 18/9CrNi heat resisting steel, niobium stabilised bar 345

BS S144 S144B&D Primary hard Corrosion resisting steel bar, primary hardened 435

BS S144 S144E Fully hard Corrosion resisting steel bar, drawn, fully hardened 1623BS S144 S144F&H Primary hard Ccorrosion resisting steel bar, primary hardened 1626

BS S145 S145B&D Softened Corrosion resisting steel bar 263

BS S145 S145F&H Fully hard Corrosion resisting steel bar, fully hardened 1743

BS S201 S201 Cold worked Patented cold drawn carbon steel wire & springs 5135

BS S203 S203 Annealed Carbon steel wire & springs 5465

BS S205 S205 Cold worked Austenitic CrNi steel wire & springs, wire 1271

BS S205 S205 - Austenitic CrNi steel wire & springs, rods 1371

BS S510 S510 Softened 28ton carbon steel sheet, strip; weldable 4

BS S511 S511 Softened Deep draw'g carbon steel sheet, strip; weldable 142

BS S514 S514 Softened 50ton C-Mn steel sheet, strip ; weldable 456

BS S514 S514 Hard+Temp 50ton C-Mn steel sheet, strip; weldable 425

BS S515 S515 Softened 30ton C-Mn steel sheet, strip; weldable 527

BS S516 S516 Softened 60ton C-Mn steel sheet, strip 325

BS S517 S517 Softened 75ton C-Mn steel sheet, strip 616BS S517 S517 Hard+Temp 75ton C-Mn steel sheet, strip 245

BS S524 S524 Cold Worked 18/10CrNi corrosion resisting steel, titanium stabilised, 237

sheet [Type 321]

BS S525 S525 Cold worked 18/10CrNi corrosion resisting steel, niobium stabilised, 247

sheet [Type 347]

BS S526 S526 Softened 540 MPa; 18Cr10Ni,corrosion resisting steel, 575

titanium stabilised, sheet, strip [Type 321]

BS S527 S527 Softened 540 MPa; 18Cr10Ni corrosion resisting steel. 547

niobium stabilised, sheet, strip [Type 347]

BS S534 FE-PL1502 Softened 880-1080 MPa;CrNi steel sheet, strip; weldable [4130] 424

BS S534 FE-PL1502 Hard+Temp 880-1080 MPa;CrNi steel sheet, strip; weldable [4130] 354

BS S535 S535 Softened 1150-1300 MPa CrMo steel sheet, strip; weldable 434

BS S535 S535 Hard+Temp 1150-1300 MPa CrMo steel sheet, strip; weldable 327

BS T45 T45 Hard+Temp 700 MPa steel tube; weldable; >12.5mm OD 132

BS T51 Copper M High pressure seamless copper tube 1

BS T51 Copper ½ hard High pressure seamless copper tube 6

BS T60 T60 Hard+Temp 1150 MPa CrNi steel tube; weldable;

8/18/2019 MOD Standard 05-69

29/40

DEF STAN 05-69/3


Colours:


27


BS TA 1 CP Ti [CP4 type] Annealed Commercially pure titanium sheet, strip; 290-420 MPa 1626


BS TA 3 CP Ti [CP3 type] Annealed Commercially pure titanium bar; 390-540 MPa 4354


BS TA 7 CP Ti [CP70(A) type] Annealed Commercially pure titanium bar; 540-740 MPa 4234

BS TA10 Ti-6Al-4V Annealed Titanium alloy sheet; 960-1270 MPa 1272

BS 970-3 070M20 - } 34346

BS 970-3 070M20 Cold worked } 17271

BS 970-3 070M20 N } 3636

BS 970-3 070M20 P } 1376

BS 970-3 070M55 - } 4567

BS 970-3 070M55 Cold worked } 4527

BS 970-3 070M55 N } 4725

BS 970-3 070M55 R } 4537

BS 970-3 070M55 S } 4576

BS 970-3 070M55 T } 4726

BS 970-3 080M40 - } 2635

BS 970-3 080M40 Cold worked } 3214

BS 970-3 080M40 N } 1265BS 970-3 080M40 Q } 1262

BS 970-3 080M40 R } 1251

BS 970-3 150M19 - } 3127

BS 970-3 150M19 N } Bright steel bar for general engineering purposes 2327

BS 970-3 150M19 P } 5276

BS 970-3 150M19 Q } 2427

BS 970-3 150M19 R } 1325

BS 970-3 210M15 - } 4146

BS 970-3 216M36 - } 3524

BS 970-3 230M07 - } 1426

BS 970-3 230M07 Cold worked } 1542

BS 970-3 605M36 R } 2627

BS 970-3 605M36 S } 1357

BS 970-3 605M36 T } 1362

BS 970-3 605M36 U } 1364

BS 970-3 605M36 V } 1365BS 970-3 817M40 - } 2714

BS 970-3 817M40 T } 1765

BS 970-3 817M40 U } 1572

BS 970-3 817M40 V } 1573

BS 970-3 817M40 W } 1574

BS 970-3 817M40 X } 1576

BS 970-3 817M40 Z } 1624

BS 1052 - Annealed Mild steel wire. 1264

BS1407 - - High carbon bright steel (silver steel) 474

BS1432 C101 O Copper rectangular electrical conductor bar 515

BS1433 C101 O Copper bar; electrical conductor rod 515

BS1449-1.8 HS1 - } 2457

BS1449-1.8 HS2 - } 2464

BS1449-1.8 HS14P - } 32623

BS1449-1.8 HS20 - } Hot rolled narrow steel strip based on formability 3476

BS1449-1.8 BHS4 - } 2672

BS1449-1.8 KHS12 - } 3724

BS1449-1.8 RHS4 - } 2656

BS1449-1.14 HS30 - } Hot rolled narrow steel strip supplied for heat treatment 6456

BS1449-1.14 HS40 - } and general engineering purposes 3546

BS1449-1.14 HS50 - } 6747

8/18/2019 MOD Standard 05-69

30/40

DEF STAN 05-69/3


Colours:


28


BS1449-1.15 CS30 - } Cold rolled narrow steel strip supplied for heat treatment 3516

BS1449-1.15 CS40 - } and general engineering purposes 3524

BS2871-2 C106 M Pure copper tube 154

BS2871-2 C106 O Pure copper tube subject to 70 bar pressure test 46

BS2871-2 C106 O Pure copper tube not subject to special pressure tests 13

BS2871-2 CN102 M Kunifer 10 tube. 565

BS2871-2 CZ126 M Brass tube not subject to special pressure test 1245

BS2871-2 CZ126 M Brass tube subject to 70, bar pressure test 616

BS4109 C101 O Electrolytic tough pitch HC Copper wire 4717

BS6323-4 CFS 3GBK Annealed or Mild steel tube. Annealed or normalised 232

Normalised

BS6323-4 CFS 5BK Cold worked Steel tube, hard, weldable, drawn/drawn & tempered 257

± tempered

BS6323-4 CFS 5NBK Normalised Seamless steel tube, weldable, normalised 131

DTD 118 AM503 F Mg-1.5%Mn sheet, strip;weldable 125

DTD 164 - M AlNiFe bronze bar 126DTD 189 - 18-8 Softened Corrosion resisting steel wire (locking wire) 163

DTD 253 - M TUNGUM type brass tube. 546

DTD 477 - Ni-Cu alloy tube 24

DTD5010 2014A T4 Al-CuMgSiMn plate 437

DTD5019 - M Al-Ni-Si brass tube (For pipelines and hydraulic systems) 515

DTD5030 Clad2014A T4 Clad Al-CuMgSiMn plate 157

DTD5070 Clad2618A H28 Clad Al-CuMgNiFe sheet, strip 1313

DTD5070 Clad2618A F Clad Al-CuMgNiFe sheet, strip 162

DTD5070 Clad2618A T6 Clad Al-CuMgNiFe sheet, strip 153

DTD5101 - ½ hard Mg-2%ZnMn sheet, strip 2626

DTD5273 CP Titanium Annealed Commercially pure titanium bar 1257

MAM 4911 Ti-6Al-4V Annealed Titanium alloy sheet, str ip and plate. 4315

Metric version of AMS 4911

MIL-DTL-22499 Steel shim stock 17471

MIL-S-25043 17-7PH TH1050 17-7PH corrosion resisting steel plate, sheet, strip 31713

MIL-T-9046 CP1 Annealed Commercially pure titanium sheet, strip, plate 545

MIL-T-9046 CP2 Annealed Commercially pure titanium sheet, strip, plate 323

MIL-T-9046 AB6 Annealed Titanium alloy sheet 53435

MIL-T-9046 CP3 [CP1A] Annealed Pure titanium sheet 54345

MIL-T-9047 Ti-6-4 Annealed Titanium alloy [Ti 6Al-4V] bar 1254

MIL-T-8504 18-8 Annealed 18-8 corrosion resisting steel tube 42124

8/18/2019 MOD Standard 05-69

31/40

DEF STAN 05-69/3

ANNEX B Colour Codes In Order Of Colour

Colours:


29

Colour Standard Alloy Temper

1 BS EN 3532 FE-PM2701 Softened

1 BS EN 12164 CW614N M

1 BS EN 12166 CW614N M

1 BS EN 12167 CW614N M

1 BS EN 12168 CW614N M

1 BS L 17 1200 O

1 BS L 36 1050A F

1 BS L116 1200 F

1 BS T51 Cu M


2 BS EN 12163 CW712R M

2 BS EN 12167 CW712R M

2 BS L 16 1200 H14/H24

3 BS EN 1652 CW004A H065

3 BS EN 3526 FE-PL1505 Hard+Temp

3 BS EN 3680 FE-PA3601 Softened


4 BS EN 4204 AL-P8090 T841

4 BS S510 - -

5 BS EN 1652 CW508L R410/H1205 BS EN 3526 FE-PL1505 Annealed

5 BS EN 3555 AL-P7075 T79510

5 BS EN 12163 CW712R M

5 BS EN 12167 CW712R M

6 BS EN 3344 AL-P7050 T76511

6 BS EN 3346 AL-P2014A T3

6 BS EN 12163 CW006A R200

6 BS T51 T51 ½ hard

7 BS EN 1652 CW508L R300/H055

7 BS EN 2702 AL-P6061 F

7 BS EN 3120 TI-64003 Cold worked

and stress relief stress relieved

7 BS EN 3525 FE-PL1505 Annealed

7 BS EN 4101 AL-P2024 T4

7 BS S1 S1 F

12 BS EN 485 EN AW-1200 O12 BS EN 1652 CW508L R480/H150


12 BS EN 3550 AL-P2024 T8511

12 BS EN 12165 CW712R M


13 BS EN 2813 AL-P6061 T6

13 BS EN 12449 CW024A H035

13 BS S126 S126A F

13 BS L163 Clad 2014A T3

13 BS 2871-2 C106 O

14 BS EN 3347 AL-P2024 T8511


14 BS EN 3552 AL-P2618A F


15 BS EN 2705 AL-P2017A T4

15 BS EN 3332 AL-P7475 F

15 BS EN 12164 CW721R R520

15 BS S 80 S80E Softened

15 BS L 34 1200 F

16 BS EN 2127 AL-P7075 T73510


16 BS EN 2705 AL-P2017A F

16 BS EN 3480 FE-PA3601 Hard+Temp

16 BS EN 3479 FE-PM3802 Hard+Temp

17 BS EN 2701 AL-P2024 T3

17 BS EN 4247 AL-P2024 F

23 BS EN 485 EN AW-2014A T4


23 BS EN 4313 AL-P6013 T6

24 BS EN 3478 FE-PM3603 Fully hard

24 BS EN 3342 AL-P6061 T4

24 DTD 477 - -

25 BS EN 485 EN AW-5154A H24/H34

25 BS EN 4293 AL-P7175 T73511

25 BS S 28 S28 Softened

25 BS L 54 1200 F

26 BS EN 4007 AL-P6082 O

26 BS EN 4006 AL-P6082 O


26 BS EN 4293 AL-P7175 T6511

26 BS EN 2510 AL-P2024 O27 BS EN 2509 AL-P2017A O

27 BS EN 2807 AL-P7020 T4


27 BS EN 4006 AL-P6082 H111

27 BS EN 4007 AL-P6082 H111

34 BS EN 2508 AL-P5086 H111

34 BS EN 2807 AL-P7020 T6


34 BS EN 4006 AL-P6082 T4

34 BS EN 4007 AL-P6082 T4

35 BS EN 485 EN AW-1200 H18

35 BS EN 2806 AL-P2024 F

35 BS EN 4450 AL-P7050 T762

36 BS EN 2711 AL-P2014A T6510


36 BS EN 4007 AL-P6082 T637 BS EN 3361 FE-PM1802 Softened

37 BS EN 4005 AL-P5052 O

37 BS EN 2710 AL-P2014A T4510

37 BS EN 3367 FE-PL8901 Cold worked

37 BS S 14 S14B F

45 BS EN 4004 AL-P3103 H16

45 BS EN 2709 AL-P2024 T3510

45 BS EN 2393 AL-P2017A T4

46 BS EN 2392 AL-P6061 T6


46 BS EN 2541 FE-PA3903 Cold worked

46 BS EN 4247 AL-P2024 T4

46 BS EN 12449 CW024A H035

46 BS L 44 5251 O

46 BS 2871-2 C106 O

47 BS EN 3348 AL-P2024 O

47 BS EN 2708 AL-P7075 T73510

47 BS EN 2391 AL-P6061 T4

56 BS EN 1652 CW452K M

56 BS T60 T60 Hard+Temp

8/18/2019 MOD Standard 05-69

32/40

DEF STAN 05-69/3

ANNEX A Colour Codes In Order Of Colour

Colours:


30


56 BS S 93 S93B&D Normalised

56 BS L504 ZW3 F

57 BS EN 1652 CW612N R410/H120

57 BS EN 2707 AL-P7075 T6510

57 BS EN 2390 AL-P6082 T6

57 BS EN 12164 CW612N R410/H120

57 BS EN 12165 CW612N R410/H120

57 BS EN 12166 CW612N R410/H120

57 BS EN 12167 CW612N R410/H120

57 BS EN 12168 CW612N R410/H120

67 BS EN 3341 AL-P6061 T4

67 BS EN 2389 AL-P6082 T4

123 BS EN 485 EN AW-1080A H18

123 BS EN 2704 AL-P2024 T3511

123 BS T72 T72 Softened

124 BS EN 2702 AL-P6061 T6


124 BS EN 2388 AL-P2024 T351

125 DTD 118 AM503 F

125 BS EN 1652 CW004A R200/H040126 BS EN 4209 AL-P2219 T851

126 DTD 164 - M

127 BS EN 2387 AL-P2014A T6

127 BS EN 3336 AL-P7150 T651

131 BS EN 485 EN AW-6082 O

131 BS EN 1652 CW452K R500/H160

131 BS 6323-4 CFS 5NBK Normalised

132 BS EN 485 EN AW-6082 T4


132 BS T45 T45 Hard+Temp

134 BS EN 485 EN AW-6082 T6

134 BS EN 1982 CC481K M

134 BS S114 S114B&D Hard+Temp

135 BS EN 1652 CW451K R310/H075

135 BS EN 2700 AL-P6061 T6

135 BS EN 4212 AL-P5086 H111136 BS EN 2511 AL-P7075 W51

136 BS EN 2699 AL-P5086 H111


137 BS EN 2512 AL-P7175 T7351

137 BS EN 2698 AL-P7075 T6510


141 BS EN 4213 AL-P6061 T451

142 BS EN 2632 AL-P7075 T6511

142 BS S511 S511 Softened

143 BS EN 485 EN AW-1050A H14

145 BS EN 755 EN AW-1050A F

145 BS EN 485 EN AW-1050A O

145 BS S 95 S95B&D Hard+Temp

146 BS EN 2525 TI-P99001 Annealed

146 BS EN 2805 AL-P7475 T7651

147 BS EN 2655 AL-P2017A F

147 BS EN 485 EN AW-1050A H18

147 BS EN 1652 CW450K R290/H070

151 BS EN 2804 AL-P7075 T7651

152 BS EN 1652 CW451K R400/H120

152 BS EN 2640 AL-P2017A T4


152 BS L 59 3103 H16/H26

153 BS EN 2639 AL-P2014A T4

153 DTD5070 Clad 2618A T6

154 BS EN 2639 AL-P2014A T6

154 BS EN 2803 AL-P7475 T761


154 BS EN 12449 CW024A M

154 BS 2871-2 C106 M

156 BS EN 2638 AL-P2024 T3

157 BS EN 2637 AL-P7075 T73

157 BS EN 2573 FE-PA3601 Cold worked


157 BS EN 1652 CW004A R290/H090

161 BS EN 2802 AL-P7475 T761

161 BS EN 3513 FE-PL8201 Softened

161 BS EN 2637 AL-P7075 T6

161 BS EN 1652 CW452K R640/H200

162 BS EN 2636 AL-P6082 T6

162 DTD5070 Clad 2618A F

162 BS EN 1652 CW450K R610/H190


163 BS EN 2635 AL-P2014A T6511

163 DTD 189 18-8 Softened

165 BS EN 2634 AL-P2014A T4511

165 BS EN 2212 FE-PL1502 Soft

165 BS EN 2211 FE-PL1502 Soft165 BS S 97 S97B&D Hard+Temp

167 BS EN 2633 AL-P2024 T3511



167 BS L113 6082 T652

171 BS EN 2203 NI-PH1303 Solution

treated

171 BS EN 2703 AL-P2024 T4


172 BS EN 485 EN AW-1200 H16

172 BS EN 2632 AL-P7075 T73511

172 BS EN 2073 AL-P1050A H14


173 BS EN 485 EN AW-1200 H12

174 BS EN 485 EN AW-1200 H14

174 BS EN 2631 AL-P7075 T6511174 BS EN 2814 AL-P2024 T3

175 BS EN 3553 AL-P2618A T6510

176 BS EN 3337 AL-P7010 T74511

212 BS EN 485 EN AW-3103 O

212 BS EN 1652 CW451K R550/H180

214 BS EN 485 EN AW-3103 H12

215 BS EN 2632 AL-P7075 T73510


216 BS EN 2394 AL-P7075 T6511


217 BS EN 2696 AL-P7075 T6

217 BS S513 S513 Hard+Temp


232 BS L 81 5251 H16/H26

232 BS 6323-4 CFS 3GBK Annealed/N

234 BS EN 2384 AL-P2014A T6511



236 BS EN 2326 AL-P6082 T6

236 BS EN 10305-2 E235+A U

237 BS S524 S524 Cold worked

237 BS S 99 S99E&G Hard+Temp

242 BS EN 485 EN AW-3103 H16


243 BS EN 485 EN AW-5154A H22/H32

243 BS S 99 S99B&D Softened

245 BS EN 2325 AL-P2014A T6

8/18/2019 MOD Standard 05-69

33/40

DEF STAN 05-69/3


Colours:


31



246 BS EN 2695 AL-P6081 T6

247 BS EN 485 EN AW-5154A O


252 BS EN 2694 AL-P6061 T6

252 BS EN 2324 AL-P2014A T6

253 BS EN 2323 AL-P2014A T651


253 BS EN 2695 AL-P6081 T4

254 BS EN 2321 AL-P2024 T3


256 BS EN 2320 AL-P2024 T4

256 BS EN 1652 CW006A R220/H040

257 BS EN 2693 AL-P5086 H111

257 BS EN 2319 AL-P2024 T3510

257 BS 6323-4 CFS 5BK Cold worked

± tempered

257 BS EN 1652 CW006A R240/H065


262 BS EN 2692 AL-P2017A T3262 BS EN 2318 AL-P2024 T3511

263 BS EN 2691 AL-P2017A T3

263 BS EN 2318 AL-P2024 T3510

263 BS S145 S145B&D Softened

264 BS EN 2317 AL-P7075 T73

264 BS EN 2689 AL-P7050 T73651

264 BS EN 1652 CW006A R290/H090

265 BS EN 2317 AL-P7075 T6

267 BS EN 2316 AL-P7075 T73

267 BS EN 2687 AL-P7010 T7651

267 BS EN 3492 FE-PM3502 Annealed

272 BS L 85 6066 T6

272 BS L 61 3103 O


273 BS EN 2315 AL-P7075 T73510

273 BS EN 1652 CW451K R490/H160274 BS EN 485 EN AW-3103 H18

274 BS EN 2315 AL-P7075 T73511

274 BS T64 T64 Tempered

274 BS L105 2014A T3


275 BS EN 485 EN AW-3103 H14


275 BS HR203 NIMONIC 75 Softened

276 BS EN 2128 AL-P7075 T7351

313 BS EN 2684 AL-P7010 T7651

314 BS EN 755 EN AW-5251 F

314 BS EN 485 EN AW-5251 O

315 BS EN 3333 AL-P7475 T761


316 BS EN 2128 AL-P7075 T651

316 BS EN 3982 AL-P7050 W51

316 BS EN 3983 AL-P7050 W51


323 MIL-T-9046 CP2 Annealed

323 BS EN 2127 AL-P7075 T651

324 BS EN 3998 AL-P2024 F

324 BS EN 2100 AL-P2014A T451

325 BS EN 485 EN AW-1080A H14


325 BS EN 1652 CW452K R420/H125


326 BS EN 1652 CW451K R630/H200

327 BS EN 485 EN AW-1080A O




treated


343 BS EN 2316 AL-P7075 T6

345 BS EN 2323 AL-P2014A T451



346 BS EN 2384 AL-P2014A T4511

346 BS EN 1652 CW452K R720/H220

346 BS EN 3335 AL-P7475 O2


treated

347 BS EN 2422 AL-P2124 T351

347 BS EN 3471 FE-PA3903 Hard + cold

rolled

353 BS EN 12166 CW024A H105354 BS S534 FE-PL1502 Hard+Temp

354 BS EN 1652 CW452K R350/H080

356 BS EN 2419 AL-P2024 T351



treated

357 BS EN 2395 AL-P2014A T4


363 BS L168 2014A T6510

363 BS EN 13602 CW004A R200

364 BS EN 2395 AL-P2014A F

364 BS L168 2014A T6511

364 BS EN 13602 CW004A D

365 BS L 85 6066 T651

365 BS EN 13601 CW004A R200

367 BS EN 2126 AL-P7075 T7651367 BS EN 3512 FE-PL1801 Cold rolled

373 BS EN 1652 CW508L R550/H170

373 BS EN 2125 AL-P2214 6151

373 BS EN 2711 AL-P2014A T4510

375 BS EN 2700 AL-P6061 T4

375 BS EN 13601 CW004A D


376 BS EN 2635 AL-P2014A T4511


414 BS L 60 3103 H12/H22


415 BS L 85 6066 F

415 BS L 80 5251 O

417 BS L114 6082 T6510

424 BS L 44 5251 F

424 BS S534 FE-PL1502 Softened

425 BS EN 2804 AL-P7075 W51


425 BS EN 2123 AL-P2618A T351

426 BS EN 3343 AL-P7010 T76511


427 BS EN 2092 AL-P7075 F

427 BS EN 12449 CW024A R290/H090

427 BS EN 1652 CW024A R240/H065

427 BS EN 3510 FE-PA2602 Fully hard

8/18/2019 MOD Standard 05-69

34/40

DEF STAN 05-69/3


Colours:


32


426 BS EN 2123 AL-P2618A T851


434 BS S143 S143B&D Fully hard

434 BS L102 2014A T4511

434 BS L 88 Clad7075 T6

435 BS EN 2092 AL-P7075 T6

435 BS S144 S144B&D Primary hard


436 BS EN 2091 AL-P2024 T4


436 BS EN 1652 CW024A R290/H090

437 BS EN 4207 AL-P8090 T89

437 BS EN 10025 NA S275 -

National Annex



457 BS EN 2090 AL-P2024 T3

457 BS S 82 S82B&D Softened

457 BS EN 1652 CW004A M

464 BS EN 2089 AL-P2014A T6465 BS EN 3358 FE-PM1503 Fully hard

465 BS EN 10305-2 E355 +N

465 BS EN 2089 AL-P2014A T4

465 BS EN 1652 CW024A M

467 BS EN 3553 AL-P2618A T6511

467 BS EN 10305-2 E355 +C

467 BS EN 1652 CW004A H040

474 BS EN 2089 AL-P2014A F


474 BS EN 12163 CW451K M

474 BS 1407 - -

476 BS EN 1652 CW024A H040


515 BS EN 2088 AL-P2014A F

515 BS L 63 2014A T6

515 BS L 37 2014A H13515 BS B27 TUNGUM M

515 BS 1433 C101 O

515 BS 1432 C101 O

515 DTD 5019 - M

516 BS EN 3551 AL-P7150 T6511


525 BS EN 2088 AL-P2014A T4

526 BS EN 2519 TI-P99003 F

526 BS EN 2087 AL-P2014A T6

527 BS EN 2087 AL-P2014A F


535 BS EN 2087 AL-P2014A T4

535 BS EN 12166 CW508L R550/H155

536 BS EN 2072 AL-P1050A H14

537 BS EN 3998 AL-P2024 O


545 MIL-T-9046 CP1 Annealed


546 AMS 4902 CP-3 [CP-1A] Annealed

546 DTD 253 - M


565 BS EN 12451 CW352H M

565 BS 2871-2 CN 102 M


567 BS EN 12164 CW612N M

567 BS EN 12166 CW612N M

567 BS EN 12167 CW612N M



576 BS EN 2211 FE-PL1502 Tempered

616 BS EN 3997 AL-P2024 T3


616 BS EN 12451 CW707R M

616 BS 2871-2 CZ126 M

617 BS EN 3996 AL-P1100 H14

627 BS EN 2125 AL-P2214 T451

627 BS EN AL-P2024 T3510


637 BS L 56 5251 O

637 BS EN 13602 CW004A M

646 BS EN 4211 AL-P2024 O

646 BS EN 13601 CW004A M



657 BS EN 4213 AL-P6061 T651

676 BS EN 2687 AL-P7010 W51

676 BS B27 - M

717 BS EN 485 EN AW-5083 O

717 BS S 62 S62B&D Hard+Temp717 BS EN 1652 CW508L R350/H095

717 BS EN 3345 AL-P7150 T6511

727 BS EN 4202 AL-P6082 T651

737 BS EN 485 EN AW-5083 H22/H32

737 BS S 15 S15B&D F

747 BS EN 2092 AL-P7075 O

757 BS EN 2704 AL-P2024 T3510

757 BS EN 2511 AL-P7075 T7351

767 DTD 503 - -

767 BS EN 4211 AL-P2024 F

1217 BS EN 3333 AL-P7475 F

1217 BS EN 12449 CW508L R280/H065

1217 BS HR208 INCONEL 600 Annealed

1235 BS EN 12449 CW508L R350/H085

1241 BS EN 12449 CW508L M

1245 BS 2871-2 CZ126 M1247 BS EN 12164 CW721R M

1247 BS EN 12165 CW721R M

1251 BS 970-3 080M40 R

1253 BS EN 1652 CW354H R350/H080

1254 MIL-T-9047 Ti-6-4 Annealed

1257 DTD5273 - Annealed

1262 BS 970-3 080M40 Q

1263 BS EN 3512 FE-PL1801 Spheroidised

1264 BS 1052 - Annealed

1265 BS 970-3 080M40 N


1272 BS TA10 Ti-6Al-4V Annealed

1275 BS EN 12451 CW707R R320/H080

1276 BS EN 12165 CW721R O

1313 DTD5070 Clad 2618A H28

1314 BS TA 2 CP Ti [CP3 type] Annealed

1324 BS EN 2634 AL-P2014A T4510

1325 BS 970-3 150M19 R

1327 BS 970-3 150M36 R

1341 BS 970-3 150M36 S

1341 AMS 4901 CP-1 [CP-1B] Annealed

1343 BS EN 4215 AL-P7175 T651

1351 BS EN 12167 CW721R R520

1351 BS EN 12168 CW721R R520

1352 BS EN 2114 AL1050A H14

1357 BS 970-3 605M36 S

1362 BS 970-3 605M36 T

8/18/2019 MOD Standard 05-69

35/40

DEF STAN 05-69/3


Colours:


33


1364 BS 970-3 605M36 U

1365 BS 970-3 605M36 V

1371 BS S205 S205 F

1376 BS 970-3 070M20 P





1426 BS 970-3 230M07 -

1427 AMS 4900 CP-2 (CP-1C) Annealed

1432 AMS 4908 Ti-Mn Annealed

1434 BS EN 12451 CW352H R290/H080

1464 BS EN 10084 1.6566 U

1465 BS EN 12166 CW505L R530/H145

1473 BS EN 2702 AL-P6061 T4

1473 BS EN 10025 S355JR [1.0045] -

1512 BS EN 10025 S355J0 [1.0533] -

1524 BS EN 2635 AL-P2014A T6510


1532 BS EN 2475 FE-PL2106 Softened1542 BS EN 2635 AL-P2014A T4510

1542 BS EN 4099 AL-P2219 H111

1542 BS 970-3 230M07 Cold worked

1543 BS EN 3338 AL-P7050 T74511

1546 BS EN 4003 AL-P2219 T87


1572 BS 970-3 817M40 U

1573 BS EN 4457 AL-P7475 T7651

1573 BS 970-3 817M40 V

1574 BS 970-3 817M40 W


1576 BS 970-3 817M40 X

1613 BS EN 3342 AL-P6061 O

1614 BS EN 12163 CW024A M

1614 BS EN 12167 CW024A M

1623 BS S144 S144E Fully hard1624 BS 970-3 817M40 Z

1626 BS TA 1 CP Ti [CP4 type] Annealed

1626 BS S144 S144F&H Primary hard

1634 BS EN 4002 AL-P2219 T81

1646 BS EN 2696 AL-P7075 O

1652 BS EN 4283 AL-P2219 T37

1657 BS EN 2703 AL-P2024 O

1671 BS L113 6082 W

1672 BS EN 2127 AL-P7075 T73511

1674 BS EN 2703 AL-P2024 F



1716 BS EN 1652 CW503L R320/H085

1737 BS EN 485 EN AW-5083 H24/H34



1743 BS S145 S145F&H Fully hard


1765 BS 970-3 817M40 T

2123 BS EN 2126 AL-P7075 T651

2124 BS L164 Clad 2014A F

2125 BS EN 2696 AL-P7075 F

2127 BS EN 4001 AL-P2024 T351

2132 BS L164 Clad 2014A T4

2136 AMS 5556 Type 347 Softened


2136 BS EN 4457 AL-P7475 T7351

2137 BS EN 2694 AL-P6061 O

2143 BS EN 2684 AL-P7010 W51

2145 BS L164 Clad 2014A T42

2145 BS 1449-1 HR4 & HR14-GP -

2146 BS EN 10025 S275JR [1.0044] -


2164 BS EN 2694 AL-P6061 T4

2165 BS EN 2694 AL-P6061 H111

2175 BS EN 3474 AL-P2024 T3




2323 BS L168 2014A T6

2323 BS EN 1652 CW612N R420/H120


2324 BS L165 Clad 2014A T6

2324 BS EN 10088-2 1.4301 AT+2D


2325 BS EN 10088-2 1.4301 2H [CW]2326 BS EN 1652 CW612N R490/H150

2326 BS EN 3342 AL-P6061 F

2327 BS EN 485 EN AW-2014A T6

2327 BS EN 10083-1 150M19 N

National Annex

2327 BS 970-3 150M19 N

2342 BS EN 4207 AL-P8090 T39

2343 BS EN 4099 AL-P2219 O

2345 BS L165 Clad 2014A T62

2352 BS EN 1652 CW612N R560/H175

2354 BS EN 4283 AL-P2219 T87

2372 BS EN 2702 AL-P6061 O

2373 BS EN 4002 AL-P2219 T31

2375 BS EN 1652 CW500L R230/H045

2375 BS EN 3341 AL-P6061 F

2416 BS EN 4102 AL-P2219 T812453 BS EN 12166 CW508L R550/H155

2467 BS EN 4003 AL-P2219 T37

2514 BS EN 485 EN AW-3103 F

2515 BS EN 1652 CW352H R300/H070

2516 BS EN 3341 AL-P6061 O

2517 BS EN 4209 AL-P2219 T351

2524 BS EN 3474 AL-P2024 T81



2624 BS 970-3 150M36 Q

2626 DTD5101 - ½ hard

2627 BS 970-3 605M36 R

2635 BS 970-3 080M40 -

2637 BS EN 10083-1 605M36 U

National Annex

2637 BS 970-3 605M36 -

2646 BS 1449-1 HR4 & HR14P -

2653 AMS 5571 Type 347 Softened

2656 BS 1449-1.8 RHS4 -

2657 BS EN 10084 C16E [1.1148] U

2657 BS 1449-1 CSA4 Annealed

2673 BS S164 S164C&E Hard+Temp

2673 BS 1449-1 CR4-GP -

2674 BS 1449-1 CR4-FF -

2676 BS 1449-1 CSSP4 -

8/18/2019 MOD Standard 05-69

36/40

DEF STAN 05-69/3


Colours:


34


2714 BS EN 10083-1 817M40 U

National Annex

2714 BS 970-3 817M40 -

2734 BS EN 10084 665M17 U

3123 BS EN 4100 AL-P2219 O

3124 BS EN 4100 AL-P2219 H111

3125 BS EN 3341 AL-P6061 H111

3125 BS EN 10277-2 C40 [1.0511] U+C+SH/SL

3124 BS EN 10277-2 C40 [1.0511] U+SH/SL

3125 BS EN 10305-2 E235 +C

3137 BS EN 10277-5 C40E [1.1186] QT+C+

SH/SL

3143 BS EN 485 EN AW-5251 F

3143 BS EN 10277-5 C40E [1.1186] QT+SH/SL

3145 BS L158 2014A T42

3147 BS EN 485 EN AW-5251 H22/H32

3153 BS L158 2014A T4

3157 BS EN 2212 FE-PL1502 Normalised ±

temper

3214 BS 970-3 080M40 Cold worked3235 BS L159 2014A T6

3243 BS EN 12166 CW024A M

3273 BS EN 485 EN AW-1080A F

3424 BS EN 485 EN AW-5251 H24/H34

3427 BS EN 10083-1 150M36 U

National Annex

3427 BS 970-3 150M36 -

3434 QQ-S-766 301 Hard

3453 BS L168 2014A T6510

3453 BS EN 12166 CW502L R540/ H165

3454 BS L168 2014A T6511

3463 BS EN 10083-1 826M40 U

National Annex

3516 BS 1449-1.15 CS30 -

3524 BS 970-3 216M36 -

3524 BS 1449-1.15 CS40 -3526 BS EN 10083-1 120M36 U

National Annex

3526 BS EN 12166 CW505L R620/H170

3545 AMS-QQ-A-200/8 6061 T6511

3614 BS EN 754 EN AW-1050A F

3616 BS EN 754 EN AW-5251 F

3616 BS EN 10277-3 15SMn13 [1.0725] U+SH+SL

3617 BS EN 10277-3 15SMn13 [1.0725] U+C+SH/SL

3624 BS EN 10087 15SMn13 [1.0725] U

3625 BS EN 12166 CW508L R280/H065


3635 BS EN 3983 AL-P7050 T7651

3635 BS EN 12166 CW508L R700/H190

3636 BS EN 3982 AL-P7050 T7451

3636 BS 970-3 070M20 N

3647 BS EN 2506 FE-PM1801 Soft

3725 BS EN 2087 AL-P2014A O



3735 BS 1449-1 CR4 -

3737 BS EN 3332 AL-P7475 O


3745 BS EN 4313 AL-P6013 T4

3746 BS EN 2394 AL-P7075 T6510

4146 BS 970-3 210M15 -

4234 BS TA 7 CP Ti [CP70(A)] Annealed

4234 BS L167 Clad 2014A T6


4245 BS S164 S164B&D Softened


4254 BS TA 6 CP Ti [CP1] Annealed

4257 BS L167 Clad 2014A T62

4315 AMS 4911 Ti-6Al-4V Annealed

4315 MAM 4911 Ti-6Al-4V Annealed

4327 BS L166 Clad 2014A T42

4345 BS L166 Clad 2014A F

4354 BS TA 3 CP Ti [CP3] Annealed

4356 BS EN 2631 AL-P7075 T6510


4364 BS EN 3333 AL-P7475 O

4365 BS EN 4449 AL-P7050 T7651

4374 BS L166 Clad 2014A T4

4526 BS EN 3334 AL-P7050 T7651

4527 BS 970-3 070M55 Cold worked

4537 BS 970-3 070M55 R

4567 BS 970-3 070M55 -

4574 BS EN 12166 CW452K R340/H080

4576 BS 970-3 070M55 S4576 BS EN 12166 CW452K R510/H160

4617 BS EN 12166 CW452K R740/H215

4626 BS EN 12166 CW452K R900/H245

4627 BS EN 3999 AL-P2024 T351

4717 BS 4109 C101 O

4725 BS 970-3 070M55 N

4726 BS 970-3 070M55 T

4745 BS EN 485 EN AW-5083 F




5175 BS 1449-1 HR43/25 -

5245 BS EN 10277-5 C40E [1.1186] N+C+SH/SL


5416 AMS 4071 5052 O

5465 BS S203 S203 Annealed5637 BS 970-3 216M36 P

5647 BS EN 10025 S275J0 [1.0553] -

5656 BS EN 485 EN AW-1100 H19


7127 BS EN 485 EN AW-1200 F

7137 BS S204 S204 Annealed

7147 AMS 4182 1100 F

7157 AMS-QQ-A-430 1100 F

7157 BS EN 3332 AL-P7475 T761

7167 BS L113 6082 O

7237 BS EN 3552 AL-P2618A H28

7267 BS EN 4247 AL-P2024 O

7357 BS EN 4214 AL-P7010 T651

7367 BS EN 4102 AL-P2219 T31

13145 BS EN 10083-1 605M36 QT

National Annex

13156 BS EN 10083-1 817M40 QT

National Annex

13231 AMS 6415 4340 Normalised

13631 AMS 6415 4340 Softened

13731 AMS 6415 Hard+Temp

14135 BS EN 10083-1 C40E [1.1186] U

14136 BS EN 10083-1 C40E [1.1186] N

14137 BS EN 10083-1 C40E [1.1186] QT

15135 BS EN 10083-1 28Mn6 U

15136 B