Upload
trinhdiep
View
222
Download
1
Embed Size (px)
Citation preview
Model PA300 SeriesELECTRONIC SIREN
MODELS 690009, 690010, 690016
INSTALLATION AND OPERATING INSTRUCTIONS
255359BREV. B 1209Printed in U.S.A.
SECTION IGENERAL DESCRIPTION
The Model PA300 Series can drive one or two 11-ohm impedance, high power (100 W) or low power (58 W) speakers. When two speakers are used, they must be connected in parallel and in phase.
The Tap II feature allows the driver to change the siren sound from Wail to Yelp (or vice-versa) via the vehicle horn ring. Tap II provides especially effec-tive traffic clearing capability. In addition to Tap II, additional alternate sounds can be activated in two other selector-switch positions by pressing and hold-ing the horn ring for as long as the alternate sound is desired. The charts in Section IV of this manual illustrate the operation of these features more fully.
Other special features of the Model PA300 Series include:
• Highdegreeofreliabilityisachieved through the use of integrated circuits and silicon output transistors.
• Controlpanelisilluminatedwith LEDs.
• Newlydesignedprintedcircuitboard provides improved performance and durability under a wide range of environmental conditions.
PA300 Series Models:
• 690009:24V,200W,Hi-Lotonewith microphone
• 690010:12V,200W,Hi-Lotonewith microphone • 690016:12V,200W,Prioritytonewith microphone
-1-
Figure 1-1. Model PA300 Series Electronic Siren
The Federal Signal PA300 Series (Figure 1-1) comprises precision-built, efficient and economical, full-featured electronic sirens of advanced design. Models690009and690010provideWail,YelpandHi-Losirentones,aswellastheTapIIfeature,publicaddress (PA), radio rebroadcast and an air horn sound.TheModel690016providesallthefeaturesofthe other models with a Priority (rapid Yelp) tone in placeoftheHi-Lotone.
The siren should be installed in negative-ground vehicles. It is protected against failure modes (includ-ing reversed polarity) by a fuse that is replaceable withouttools.Nocomponentsprotrudefromthebot-tom of the siren to interfere with mounting arrange-ments.
A noise-cancelling microphone is wired-in to prevent loss or theft. It provides high quality voice reproduction without feedback “squeal." The micro-phone push-to-talk switch overrides any siren signal for instant PA use. PA and radio volume are adjust-ablebymeansofafrontpanelGAINcontrol.Radiointerconnectwiresarebuilt-in.Noadditionalcablesare required.
290A4507-01
-2-
SECTION IISPECIFICATIONS
Input Voltage ................................................................. 11Vdcto15Vdc(690010and690016) 24Vdcto28Vdc(690009)
Polarity .......................................................................... Negativegroundonly
StandbyCurrent(Manualtone) ................................... 120mA(typical)(690010and690016) 120mA(typical)(690009)
OperatingTemperatureRange ..................................... –30°Cto+65°C.
OperatingCurrent(Wailtone) ..................................... 10amperesmax.at13.6Vdc(690010and690016) 5amperesmax.at25Vdc(690009) (11 ohm load at high power)
FrequencyRange(typical) ............................................ 725Hzto1800Hz
CycleRate(typical) ....................................................... Wail: 15 cycles/min. Yelp:220cycles/min. Hi-Lo:70cycles/min.(690009and690010) Priority:1,300/min.(690016)
Voltage Output (approx.) .............................................. 64Vpeak-to-peak(11-ohmload)
Dimensions(HWD) ....................................................... 2-1/2"(6.35cm)x6-1/2"(16.51cm)x8-1/2"(21.59cm)
NetWeight(includesmicrophone) ............................... 4-1/2lb(2.04kg)
Shipping Weight ............................................................ 6-1/2lb(2.94kg)
NOTE
The following parameters were obtained with the radioinputpotentiometerandGAINcontrolset at maximum.
AudioFrequencyRange ................................................ 300Hzto10,000Hz
HarmonicAudioDistortion(300Hzto3,000Hz) ........ 10% max. all power levels from 0.50 W to 50 W (frequency response ±3 dB)
InputImpedance(Radio) .............................................. 2,000ohms.
Inputvoltagerequiredtoobtain20Vrmsacrossspeakerload(Radio) ..................................................... 0.30 Vrms
-3-
SECTION IIIINSTALLATION
SAFETY MESSAGE TO INSTALLERSOF ELECTRONIC SIRENS
WARNINGThe lives of people depend on your proper installation and servicing of Federal Signal products. It is impor-tant to read and follow all instructions shipped with the products. In addition, listed below are some other important safety instructions and precautions you should follow:
Before Installation
Qualifications
• Toproperlyinstallanelectronicsiren,youmusthaveagood understanding of automotive electrical procedures and systems, along with proficiency in the installation and service of safety warning equipment. Always refer to the vehicle’s service manuals when performing equip-ment installations on a vehicle.
Sound Hazards• Yourhearingandthehearingofothers,inorcloseto
your emergency vehicle, could be damaged by loud sounds. This can occur from short exposures to very loud sounds, or from longer exposures to moderately loud sounds. For hearing conservation guidance, refer to fed-eral,state,orlocalrecommendations.OSHAStandard1910.95offersguidanceon“PermissibleNoiseExposure.”
• Alleffectivesirensandhornsproduceloudsounds(120dB) that may cause permanent hearing loss. Always minimizeyourexposuretosirensoundandwearhearingprotection. Do not sound the siren indoors or in enclosed areas where you and others will be exposed to the sound.
• FederalSignalsirenamplifiersandspeakersarede-signedtoworktogetherasasystem.Combiningasirenand speaker from different manufacturers may reduce the warning effectiveness of the siren system and may damage the components. You should verify or test your combination to make sure the system works together properly and meets federal, state and local standards or guidelines.
During Installation
• DONOTgetmetalshavingsinsidetheproduct.Metalshavings in the product can cause the system to fail. If drilling must be done near the unit, place an ESD approved cover over the unit to prevent metal shavings from entering the unit. Inspect the unit after mounting to be sure there are no shavings present in or near the unit.
• DONOTconnectthissystemtothevehiclebatteryuntilALL other electrical connections are made, mounting of all components is complete, and you have verified that no shorts exist. If wiring is shorted to vehicle frame, high currentconductorscancausehazardoussparksresultingin electrical fires or flying molten metal.
• Besurethesirenamplifierandspeaker(s)inyourinstal-lation have compatible wattage ratings.
• Inorderfortheelectronicsirentofunctionproperly,thegroundconnectionmustbemadetotheNEGATIVEbat-tery terminal.
• Soundoutputwillbeseverelyreducedifanyobjectsare in front of the speaker. If maximum sound output is required for your application, you should ensure that the
front of the speaker is clear of any obstructions.
• Installthespeaker(s)asfarforwardonthevehicleaspossible, in a location which provides maximum signal-ingeffectivenessandminimizesthesoundreachingthevehicle’soccupants.RefertotheNationalInstituteofJustice guide 500-00 for further information.
• Mountingthespeakersbehindthegrillewillreducethesound output and warning effectiveness of the siren sys-tem. Before mounting speakers behind the grille, make sure the vehicle operators are trained and understand that this type of installation is less effective for warning others.
• Soundpropagationandwarningeffectivenesswillbeseverely reduced if the speaker is not facing forward. Carefullyfollowtheinstallationinstructionsandalwaysinstall the speaker with the projector facing forward.
• DONOTinstallthespeaker(s)orroutethespeakerwires where they may interfere with the operation of air bag sensors.
• Installationoftwospeakersrequireswiringspeakersinphase.
• Neverattempttoinstallaftermarketequipment,whichconnects to the vehicle wiring, without reviewing a ve-hicle wiring diagram available from the vehicle manufac-turer. Insure that your installation will not affect vehicle operation and safety functions or circuits. Always check vehicle for proper operation after installation.
• DONOTinstallequipmentorroutewiringorcordinthedeployment path of an airbag.
• Ifavehicleseatistemporarilyremoved,verifywiththevehicle manufacturer if the seat needs to be recalibrated for proper airbag deployment.
• Locatethecontrolheadsothevehicle,controls,andmicrophone can be operated safely.
• Whendrillingintoavehiclestructure,besurethatbothsides of the surface are clear of anything that could be damaged.
After Installation
• Afterinstallation,testthesirensystemandlightsystemto ensure that it is operating properly.
• Testallvehiclefunctions,includinghornoperation,vehicle safety functions and vehicle light systems, to en-sure proper operation. Ensure that installation has not affected vehicle operation or changed any vehicle safety function or circuit.
• Aftertestingiscomplete,provideacopyoftheseinstruc-tions to the instructional staff and all operating personnel.
• Filetheseinstructionsinasafeplaceandrefertothemwhen maintaining and/or reinstalling the product.
Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death.
Figure 3-1. Installation of PA300 Under Dash
-4-
CAUTION
Damage to unit will occur if not properly fused.Ensurethatanin-linefuse(20A)andfuseholder are installed in the red power cableleadforthe690010.Achassismountedfuseholderismountedonthe690009—ensurethat a 10-ampere fuse is installed.
3-1. UNPACKING
After unpacking the Model PA300 Series, exam-ine it for damage that may have occurred in transit. If the equipment has been damaged, file a claim immediately with the carrier stating the extent of damage.Carefullycheckallenvelopesshippinglabelsand tags before removing or destroying them.
Before proceeding with installation, ensure that the following parts have been included in the carton.
KITCONTENTSLIST
Qty.Description PartNo.
1 CableAssy.(690010and690016) 14613601 CableAssy.(690009) 14613882 Lockwasher,1/4 7074A0152 Screw,1/4-20x1/2 7002A008-081 Mtg.Bracket 853610591 Label,Warning 1612339 3-2. MOUNTING BRACKET
WARNING
When installing equipment inside airbag equipped vehicles, the installer MUST ensure that the equipment is installed ONLY in areas recommended by the ve-hicle manufacturer.
Failure to observe this warning will reduce the effectiveness of the air bag, damage the airbag, or potentially dam-age or dislodge the equipment, causing serious injury or death to you or others.
The electronic siren comes equipped with a swinging bracket which enables it to be mounted in variety of positions. Positioning the bracket above the unit allows mounting to the underside of the dash. Positioning the bracket below the unit will permit mountingonanyhorizontalsurface.
The unit should be mounted in a position that is both comfortable and convenient to the operator. Keep visibility and accessibility of controls in mind.
To install the unit under the dash, determine the mounting location and proceed as follows (see Figure 3-1).
CAUTION
The unit must be installed in an adequately ventilatedarea.Neverinstalltheunitnearheater ducts.
A. Use the mounting bracket as a template and scribe two drill positioning marks at the selected mounting location under the dash.
CAUTION
BeforedrillingholesinANYpartofavehicle,be sure that both sides of the mounting sur-face are clear of parts that could be damaged; such as brake lines, electrical wiring or other vital parts.
B. Drilltwo1/4-inchdiameterholesattheposition marks.
C. Securethemountingbrackettothedashwithuser-supplied1/4-20x3/4hexheadscrews,1/4splitlockwashersand1/4-20hexnutsasshowninFigure 3-1.
D. Secure the electronic siren to the mounting bracketwith1/4-20x1/2hexheadscrewsand1/4split lockwashers as shown in Figure 3-1.
290A4507-02NOTE:
ONLY ONE BRACKET IS SUPPLIED
1/4-20 x 1/2"HEX HD. CAPSCREW
1/4-20 x 3/4" HEX HD CAP SCREW
1/4" SPLITLOCKWASHER
1/4-20 x 1/2" HEX HD. CAP SCREW
MOUNTINGBRACKET
1/4" SPLITLOCKWASHER
1/4" SPLITLOCKWASHER
MICROPHONECABLE
CAUTION1/4-20 x 1/2"
HEX HD. CAPSCREW WITH
LOCKWASHERMUST BE USED
AS SHOWNLONGER SCREW
WILL CAUSECIRCUITRYDAMAGE.
MOUNTING UNDER DASH1/4-20 HEX NUT
-5-
Figure 3-2. Rear View of PA300
Figure 3-3. Control Cable Wiring Diagram
CAUTION
Toavoiddamagetotheunit,the1/4-20x1/2hexheadcapscrewsandthe1/4splitlock-washers must be used as shown in Figure 3-1.
E. Tilt the unit to the desired position. Tighten the1/4-20x1/2hexheadscrews.
3-3. POWER CABLE INSTALLATION
CAUTION
Wiring changes have been made which uti-lizesanewtypeofpowercable.Ifthisunitis used to replace an older PA300, use the optionalcableadaptor(761300)toconnecttheoriginally installed power cable to the new siren.
A. Speaker
The unit is designed to operate with one 11-ohm impedance speaker or two 11-ohm impedance, low power (58 W) or high power (100 W), speakers connected in parallel and in phase. On Federal Signal speakers, this can be accomplished by connecting thetwospeakerleadsmarked“1”totheSPEAKERCOMMONcontrolcableleadandthetwospeakerleadsmarked“2”totheSPEAKERHIGHPOWERorSPEAKERLOWPOWERcontrolcableleads.SeeFigure 3-3.
CAUTION
Damage to the unit will occur if speaker wiresareimproperlyconnected.NEVERCONNECTthebrownSPEAKERHIGHPOWER(100W)wireandorangeSPEAKERLOWPOWER(58W)wiretogethertothespeaker(s).
Using 18 AWG wire, connect the speaker leads(58WspeakerstoSPEAKERLOWPOWER
and100WspeakerstoSPEAKERHIGHPOWER)asshownintheControlCableWiringDiagram,Figure3-3.
B. Radio
To allow incoming radio messages to be rebroadcast over the outside speakers, connect the twobrownzipcordleads(pins1and2)acrossthetwo-way radio’s speaker.
C. Horn Ring
InordertoutilizetheTapIIandPress-and-Holdfeaturesofthesiren,thefollowingproceduremust be performed.
1. Locate the wire that connects the ve-hiclehornringswitchtothehornorhornrelay.Cutthis wire.
2. SeeFigure3-4.Splicethewhite/yellowcontrolcablewire(pin4)tothehornringsideofthewire that was cut in step 1. Insulate the splice with user-supplied wire nuts.
CAUTION
The horn ring transfer circuit of the siren is capableofswitchingamaximumof2am-peres. Some vehicles do not have a horn relay and,consequently,willdrawmorethan2am-pereswhenthevehiclehornisactivated.Con-sult your vehicle service manual or a qualified mechanic to determine the current required to activate the horn. If it is lessthan2am-peres, perform the procedure in step 3. If it is greater than2amperes,performsteps4through 10.
290A4507-03
ORG (SPKR, LO)
BRN (SPKR, HI)
WHT (HORN)
WHT/YEL (HORN RING)
BRN (RIBBED) (RADIO)
BRN (NON-RIBBED) (RADIO)
ZIP CORD
8
9
5
4
2
1
BLU (SPKR, COM)7
1 2 3 4 5
6 7 8 9 10
RED (POWER +)
FUSEHOLDER ON 690010 ONLY
BLK (GROUND -)
290A4507-04C
*
*
-6-
Figure 3-4. Horn Ring Connections
3. Splice the white control cable wire (pin 5) to the horn side of the cut wire. Insulate the splice with a user-supplied wire nut.
4. ObtainaSPSTrelayofsufficientcontact current capacity to activate the vehicle horn. RefertoFigure3-4whileperformingthefollowingsteps.
5. Mount the relay in a suitable location.
6. Connectthehornsideofthewirecutin step 1 to the relay contact terminal.
7. Determinethe“sense”ofthevehicle’shorn ring activation circuit, i.e., does the horn cir-cuit require a switched positive voltage or switched ground for activation.
8. Connecttherelaywiperterminaltothe positive or negative potential determined in step 7.
9. Connectthewhitecontrolcablewiretoone end of the relay coil.
10.Connecttheotherendoftherelaycoilto the opposite potential of that connected to the wiper in step 8.
D. Connection to Power Source.
CAUTION
Damage to unit will occur if not properly fused.Ensurethatanin-linefuse(20A)andfuseholder are installed in the red power cableleadforthe690010and690016.Achassis mounted fuseholder is mounted on the690009.Ensurethata10-amperefuseisinstalled.
The PA300 Series can operate only from a negative ground vehicle electrical system. Therefore, before making any electrical connections, determine the polarity of the vehicle electrical system ground.
Power for the siren can be obtained from the vehicle’s power distribution center or directly from the vehicle battery. If power is going to be ob-tained directly from the vehicle battery, drill a hole in the vehicle firewall for the power lead to enter the engine compartment. Place a grommet or similar device in the hole to protect the wire against damage from rough edges.
CAUTION
BeforedrillingholesinANYpartofthevehicle, ensure that both sides of the surface are clear of parts that could be damaged; such as brake lines, fuel lines, electrical wiring or other vital parts.
If your vehicle has a negative ground elec-trical system, perform the procedure as follows:
NOTE
This unit is NOT designed to operate with positive ground.
1. Routetheredpower(+)andtheblackpower (–) control cable leads, through the previously drilledhole,intotheenginecompartment.Routethewires through existing clamps and holders toward the battery.
2. Toprotecttheredwirewhenconnectedto the battery terminal, use an in-line fuseholder and an appropriate installer-supplied fuse (10-ampere forthe690009,and20-ampereforthe690010and690016).Thefuseholdershouldbeinstalledascloseas practical to the battery. If necessary, additional 14AWGorheavierwirecanbesplicedtotheredlead.
WARNING
If wires are shorted to the vehicle frame or each other, high current conductors can cause hazardous sparks resulting in electrical fires and molten metal. Verify that no short circuits exist before connect-ing to the positive (+) battery terminal.
DO NOT connect this system to the ve-hicle battery until ALL other electrical connections are made, mounting of all components is complete, and you have verified that no shorts exist. If the wiring is shorted to the vehicle body or frame, high current conductors can cause hazardous sparks resulting in electrical fires or flying molten metal.
290A4507-05
VEHICLE HORNS STEERING COLUMN
TO BATTERY
RELAY (USER SUPPLIED)
CUT WIRE
SW
TO HORN, OR HORN RELAY
CONTROL CABLE ASSEMBLY
WHT
WHT/YEL TO HORN SWITCH
-7-
Figure 3-5. Press and Hold Modification
Air Horn Configuration
Factory Configuration
1. Connectthein-linefuseholderleadtothepositive(+)batteryterminal.
2. Connecttheblackwiretothenegativeterminal of the battery.
3-4. AIR HORN PRESS-AND-HOLD MODIFICATION
The unit comes from the factory set so that the peak-and-hold sound will be heard when the Selector switchissettoMANUALandthevehiclehornringis activated. To change the sound to air horn, merely movejumpersJ8andJ9fromthe“PEAK”positionontheP.C.boardtothe“AIR”position(seeFigure3-5).
3-5. RELATIVE PA LOUDNESS ADJUSTMENT
After the electronic siren is completely installed inthevehicle,settheSelectorswitchtoMANUAL.Depress the microphone push-to-talk switch, speak inanormalvoice,andadjusttheGAINcontrolforthe desired sound level outside the vehicle. Turn-on the vehicle’s two-way radio and adjust the volume to a comfortable listening level inside the vehicle. Then settheSelectorswitchtoRADIO.Standoutsideofthe vehicle and note the radio rebroadcast loudness. If the sound volume is too loud or too soft, using a smallflatbladescrewdriver,adjustR39fromthebackofthesiren(seeFigure3-6)tothedesiredsoundlevel.
After the adjustment is completed, the loudness of the radio rebroadcast and public address may be variedwiththefrontpanelGAINcontrol.
3-6. TESTING AFTER INSTALLATION
WARNING
All effective sirens and horns produce loud sounds (120 dB) that may cause permanent hearing loss. Always mini-mize your exposure to siren sound and wear hearing protection. Do not sound the siren indoors or in enclosed areas where you and others will be exposed to the sound.
After the installation, test the electronic siren, including the horn, to ensure that they are operating properly.
After testing is complete, provide a copy of this manual to all operating personnel. Figure 3-6. Relative PA Loudness Adjustment
290A4507-06
AIRHORN
AIRHORN
PEAK
J9
J8
PEAK
J8
J9
C49
C9
C48
R21IC7 C29 R51
R31
IC10++
+ D26
R23
R26
D21
C46
PEAK
IC6
AIRHORN
PEAK
AIRHORN
IC5
R15
R16D25
+
R20
C7
R22
IC1
++
C20C8
D27
IC3R11
290A4507-07
AIRHORN
AIRHORN
PEAK
J9
J8
PEAK
J8
J9
C49
C9
C48
R21IC7 C29 R51
R31
IC10
++
+ D26
R23
R26
D21
C46
PEAK
IC6
AIRHORN
PEAK
AIRHORN
IC5
R15
R16D25
+
R20
C7
R22
IC1
++
C20C8
D27
IC3R11
R39
290A4507-08
SECTION IVOPERATION
SAFETY MESSAGE TO OPERATORS OFFEDERAL SIGNAL ELECTRONIC SIRENS
AND LIGHT/SOUND SYSTEMS
WARNING
The lives of people depend on your safe operation of Federal Signal products. It is important to read and follow all instructions shipped with the products. In addition, listed below are some other important safety instructions and pre-cautions you should follow:
Qualifications
• Toproperlyuseanelectronicsirenand speaker(s), you must have a good understanding of general vehicle operation, a high proficiency in the use of safety warning equipment, and thorough knowledge of state and federal UNIFORMTRAFFICCODES.
Sound Hazards
• Yourhearingandthehearingofothers,inor close to your emergency vehicle, could be dam- aged by loud sounds. This can occur from short exposures to very loud sounds, or from longer exposures to moderately loud sounds. For hearing conservation guidance, refer to federal, state,orlocalrecommendations.OSHAStan dard1910.95offersguidanceon“Permissible NoiseExposure.”
• Alleffectivesirensandhornsproduceloud sounds(120dB)thatmaycausepermanent hearingloss.Alwaysminimizeyourexposureto siren sound, roll up your windows and wear hearing protection. Do not sound the siren indoors or in enclosed areas where you and others will be exposed to the sound. Only use the siren for emergency response situations.
Sound Limitations
• Beforeusingthevehicle,checktoseeifthe siren speakers are concealed from view. If the siren speaker is not in clear view on the front of the vehicle, use extra caution when operating the vehicle. A concealed siren speaker installa- tion is less effective at warning others.
• Maximumsoundoutputwillbeseverelyre- duced if any objects are in front of the speaker. If your installation has obstructions in front of the speaker, drive even more cautiously.
• Frequentlyinspectthespeakertoensurethat it is clear of any obstruction, such as mud or snow, which will reduce maximum sound output.
Signaling Limitations
• Beawarethattheuseofyourvisualandau- dible signaling devices does not give you the right to force your way through traffic. Your emergency lights, siren, and actions are REQUESTINGtheright-of-way.
• Althoughyourwarningsystemisoperating properly, it may not alert everyone. People may not hear, see, or heed your warning signal. Youmustrecognizethisfactandcontinue driving cautiously.
• Situationsmayoccurwhichobstructyour warning signal when natural or man-made objects are between your vehicle and others. This can also occur when you raise your hood or trunk lid. If these situations occur, be espe- cially careful.
Driving Limitations
• Atthestartofyourshift,youshouldensure that the light/sound system is securely attached to the vehicle and operating properly.
• Iftheuniquecombinationofemergencyvehicle equipment installed in your vehicle has resulted in the siren controls being installed in a position that does not allow you to operate thembytouchonly,OPERATECONTROLS ONLYWHILEYOURVEHICLEISSTOPPED.
• Ifdrivingconditionsrequireyourfullatten- tion, you should avoid operating the siren controls while the vehicle is in motion.
Continuing Education
• Filetheseinstructionsinasafeplaceand refer to them periodically. Give a copy of these instructions to new recruits and trainees.
Failure to follow these safety precautions may result in property damage, serious injury, or death.
-8-
4-1. OVERVIEW
Allcontrolsutilizedduringnormaloperationofthe Model PA300 are located on the front panel (see Figure4-1).
The wired-in noise cancelling microphone pro-vides high quality voice reproduction in the public address mode. The microphone push-to-talk switch will override all siren functions, except radio rebroad-cast, for instant PA use.
4-2. GAIN CONTROL
TheGAINcontrolisusedtoturnthesirenonand off. Also, it is used to control the volume when the siren is used for public address or radio amplifi-cation.Clockwiserotationoftheknobincreasesvoicevolume in the public address or radio amplification mode.TheGAINcontroldoesnotcontrolthevolumeof the siren signals.
The maximum clockwise setting of the control will be determined, in most cases by the point at whichfeedbackor“squeal”occurs.Thiswilldependupon the microphone gain, open windows, speaker placement, proximity of reflecting surfaces (building orothervehicles),etc.AdjusttheGAINcontroltoaposition just below the point at which feedback occurs or as desired.
Figure 4-1. Front View
4-3. SELECTOR SWITCH
The selector switch is a five-position rotary switch used to select the mode of operation. The fol-lowing are positions on the selector switch.
A. RADIO
In this position incoming radio messages are amplified by the siren and rebroadcast over the outside speaker.
B. MANUAL
In this position it is possible to operate the sirenbyactivatingtheHORN/SIRENswitch.Thesiren can also be activated by means of an auxiliary switch, such as the horn-ring button (refer to para-graph4-6).
C. WAIL
In this position the siren produces a con-tinuous“wailing”tone,upanddowninfrequency.
D. YELP
In this position the siren produces a con-tinuous,rapid“warbled”tone.
E. HI-LO (MODELS 690009 and 690010)
In this position the siren produces a two-tone sound. This distinctive tone may be reserved for any special indication or situation.
F. PRIORITY (MODEL 690016)
In this position the siren produces a rapid "yelp" tone. This distinctive tone may be reserved for any special indication or situation.
4-4. HORN/SIREN SWITCH
TheHORN/SIRENswitch,locatedontheleftside of the front panel, activates the electronic air horn sound (up) or peak-and-hold sound (down) in any siren mode except radio.
-9-
290A4507-09
4-5. TAP II FUNCTIONS
Tap II allows the driver to change the siren sound via the vehicle horn ring. This feature is especially effective for clearing traffic. The chart below demonstrates how the horn ring can be used to change the siren sound:
TAP II FUNCTIONS
Selector Switch
Position
First Tap of the Horn Ring
Produces
Second Tap of the Horn Ring
Produces
Wail Yelp Wail
Yelp Wail Yelp
4-6. PRESS AND HOLD FUNCTIONS
Additional alternate sounds can be activated in two other selector-switch positions by depressing and holding the horn ring for as long as the alternate sound is desired. The following charts show these ad-ditionalPress-and-Holdfunctions:
PRESS AND HOLD FUNCTIONS (Models 690009 and 690010)
Selector Switch
Position
Pressing the Horn Ring Produces
Releasing the Horn Ring Produces
Hi-Lo AirHorn Hi-Lo
Manual PeakandHold,orAirHorn
Coastdownandsilence,
or silence
PRESS AND HOLD FUNCTIONS (Model 690016)
Selector Switch
Position
Pressing the Horn Ring Produces
Releasing the Horn Ring Produces
Priority AirHorn Priority
Manual PeakandHold,orAirHorn
Coastdownandsilence,
or silence
-10-
SECTION VSERVICE AND MAINTENANCE
SAFETY MESSAGE TO PERSONNEL SERVICING FEDERAL SIGNAL ELECTRONIC SIRENS
WARNING
The lives of people depend on your prop-er servicing of Federal Signal products. It is important to read and follow all instructions shipped with the products. In addition, listed below are some other safety instructions and precautions you should follow:
• Readandunderstandallinstructionsinthis manual before servicing the electronic siren or speaker.
• Toproperlyserviceanelectronicsirenor speaker: you must have a good understanding of automotive electrical procedures and systems, along with proficiency in the installation and service of safety warning equipment. Always refer to the vehicle's service manuals when performing service on a vehicle.
• Electroniccircuitandspeakerrepairsmustbe performed by a qualified and competent elec- tronic technician.
• Yourhearingandthehearingofothers,inor close to your emergency vehicle, could be dam- aged by loud sounds. This can occur from short exposures to very loud sounds, or from longer exposures to moderately loud sounds. For hearing conservation guidance, refer to federal, state, or local recommendations. OSHAStandard1910.95offersguidanceon “PermissibleNoiseExposure.”
• Alleffectivesirensandhornsproduceloud sounds(120dB)thatmaycausepermanent hearingloss.Alwaysminimizeyourexposure to siren sound and wear hearing protection. Do not sound the siren indoors or in enclosed areas where you and others will be exposed to the sound.
• DONOTconnectthissystemtothepositive terminal of the battery until servicing is com- plete, and you have verified that there are no short circuits to ground.
• Inorderfortheelectronicsirentofunction properly, the ground connection must be made totheNEGATIVEbatteryterminal.
• Afterrepair,testtheelectronicsirenand speaker system to ensure that it is operating properly.
• FederalSignalsirenamplifiersandspeakers are designed to work together as a system. Combiningasirenandspeakerfromdifferent manufacturers may reduce the warning effec- tiveness of the siren system and may damage the components. You should verify or test your combination to make sure the system works together properly and meets both federal, state and local standards or guidelines.
Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death to you or others.
5-1. OBTAINING SERVICE
For warranty service, contact your local Distrib-utor. The factory can and will service your equipment or assist you with technical problems that cannot be handled satisfactorily and promptly locally.
Communicationsandshipmentsshouldbead-dressed to:
Service Department FederalSignalCorporation 2645FederalSignalDrive UniversityPark,IL60484-3167 1-800-433-9132
-11-
5-2. REPLACEMENT PARTS LIST
Description Part No.
Transistor, Output, BUT70W 125467
Transformer,Output(690010and690016) 1461358
Transformer,Output(690009) 1461359
Fuse,20A,3AG,32V(690010and690016) 148A127
Fuse,10A,3AG,32V(690009) 148A108
Switch,Rotary 122376
Switch, Toggle 122377
Header,10-PoleMolex 140454-05
Microphone 258B577-03
MicrophoneClip 85361082
MicrophoneStrainRelief 231A148
Knob,GainControl 141A102
Knob, Selector 141A111
CircuitBoardAssy.(690009) 2005183-24
Figure 5-1. Internal View.
5-2. REPLACEMENT PARTS LIST.
Description Part No.
CircuitBoardAssy.(690010) 2005183-14
CircuitBoardAssy.(690016) 2005183-23
Switch,GainControl 106128
Harness,Wiring(690009) 1461388
Harness,Wiring(690010and690016) 1461360
Kit,InstallationAccessory(690009) 8537572
Kit,InstallationAccessory(690010 and690016)
8537561
Bracket, Mounting 8536B022
Faceplate, Logo PA300 81461864
Faceplate,PA300(690009and690010) 81461865
AdapterCable 761300
Faceplate,PA300(690016) 81461865-01
290A4507-10
MICROPHONE
TOGGLE SWITCH SELECTOR KNOBGAIN CONTROL
KNOB
GAIN CONTROL
FACEPLATE LOGO
FACEPLATE ROTARY SWITCH
OUTPUTTRANSISTOR
OUTPUT TRANSISTOR
OUTPUTTRANSFORMER
-12-