Monitoring System TAPGUARD® 260 - Reinhausen · 2013. 8. 8. · LPHD class (LPHD1) - Physical device LPHD class (LPHD1) Attribute name Attribute type Explanation Extra at-tribute

Monitoring SystemTAPGUARD® 260

Supplement

3547308/00 EN . Protocol Description IEC 61850

© All rights reserved by Maschinenfabrik ReinhausenDissemination and reproduction of this document and use and disclosure of its content are strictly prohibitedunless expressly permitted.Infringements will result in liability for compensation. All rights reserved in the event of the granting of patents,utility models or designs.The product may have been altered since this document was published.We reserve the right to change the technical data, design and scope of supply.Generally the information provided and agreements made when processing the individual quotations and ordersare binding.The original operating instructions were written in German.

Table of contents

Maschinenfabrik Reinhausen 2013 33547308/00 EN TAPGUARD® 260

Table of contents

1 Introduction......................................................................................................................... 41.1 Subject to change without notice......................................................................................................... 4

1.2 Completeness...................................................................................................................................... 4

1.3 Supporting documents......................................................................................................................... 4

1.4 Safekeeping......................................................................................................................................... 4

2 Physical interfaces.............................................................................................................. 5

3 Setting device parameters................................................................................................. 6

4 Protocol specification......................................................................................................... 74.1 Downloading ICD file........................................................................................................................... 7

5 Data points........................................................................................................................... 95.1 LLN0 class - Logical node................................................................................................................... 9

5.2 LPHD class (LPHD1) - Physical device............................................................................................. 10

5.3 YLTC1 - On-load tap-changer control/monitoring (optional).............................................................. 10

5.4 SLTC1 - On-load tap-changer monitoring......................................................................................... 12

5.5 GGIO1 - Generic process I/O............................................................................................................ 16




1 Introduction

Maschinenfabrik Reinhausen 20134 3547308/00 ENTAPGUARD® 260

IntroductionThe technical file contains detailed descriptions for implementing theIEC 61850 interface protocol.

This technical file is intended solely for specially trained and authorized per-sonnel.

Subject to change without noticeThe information contained in this technical file comprises the technical speci-fications approved at the time of printing. Significant modifications will be in-cluded in a new edition of the technical file.

The document number and version number of this technical file are shown inthe footer.

CompletenessThis technical file is incomplete without the supporting documentation.

Supporting documentsThe following documents apply to this technical file:▪ Operating instructions for TAPGUARD® 260

SafekeepingThis technical file and all supporting documents must be kept ready at handand accessible for future use at all times.

1

1.1

1.2

1.3

1.4

2 Physical interfaces


Physical interfacesThe device has been developed in accordance with applicable EMC stand-ards. In regards to complying with EMC standards, please refer to the corre-sponding chapter on the topic of "Electromagnetic Compatibility" in the devi-ce's operating instructions.

You can find additional information on wiring and routing instructions for thefiber-optic cable in the operating instructions for this device.

The following physical interfaces are available on the device for data trans-mission using the control system protocol:

RJ45 Pin1: Tx+Pin2: Tx-Pin3: Rx+Pin6: Rx-

Table 1: Interfaces available

Figure 1: SID card

1 Reset key 3 Interface for SID card updates2 Status LED 4 RJ45 (Ethernet)

2

3 Setting device parameters


Setting device parametersIn order to use the control system protocol, you need to set the device pa-rameters.

Please refer to the device's operating instructions for more information re-garding setting the device parameters.

You must set the following parameters:

Parameter Network address 0.0.0.0...255255255255Network mask 0.0.0.0...255255255255Time server address 0.0.0.0...255255255255Gateway 0.0.0.0...255255255255IED name Freely definable

Table 2: Device parameters

3

4 Protocol specification


Protocol specificationThe device provides an extract of commands and messages from the inter-face protocol IEC 61850 for communication.

You can find the device-specific data points and presettings in the device'sICD file. You can request the following documents for the device or down-load from the device:▪ MICS (Model Implementation Conformance Statement)▪ PICS (Protocol Implementation Conformance Statement)▪ PIXIT (Protocol Implementation eXtra Information for Testing)▪ TICS (Technical Issues Conformance Statement)

Please note possible restrictions and comments regarding device specificdata points and default settings listed in the documents above.

Downloading ICD fileYou can download the ICD file via FTP from the device. You have to estab-lish an ethernet connection between the device and your PC.

For a smooth download with Windows Vista/7/8 operating systems, useWindows Explorer.

Proceed as follows to download the ICD file:1. Enter ftp://gast@<IP adress> in your browser (in the example in

the diagram below, the IP adress is 192.168.0.1) and select the directo-ry home/gast.

4

Device-specific data points

4.1

4 Protocol specification


2. If necessary, confirm the password prompt without entering a password.

Figure 2: Downloading the ICD file using an Internet browser

3. Use Save as to download the ICD file (in this example ATCC.ICD).4. Other files, such as the Model Implementation Conformance Statement,

are located in the misc folder and can also be downloaded using Saveas.

5 Data points


Data pointsYou will find these abbreviations in the following tables.

N no / not availableY yes / availableM mandatoryO optionalC conditional

Table 3: Abbreviation

Also refer to2 Downloading ICD file [► 7]

LLN0 class - Logical nodeLLN0 class

Attributename

Attributetype

Explanation Extra at-tribute

Used T M/O

Common logical node informationMod INC Mode

Mode/status (e.g. enabled, disa-bled, blocked, test, test/blocked)

N Y - M

Beh INS BehaviorBehavior (e.g. enabled, disabled,blocked, test, test/blocked)

N Y - M

Health INS HealthOperational state of node (1=OK,2=warning, 3=error)

N Y - M

NamPlt LPL Name plateManufacturer information (manu-facturer=Maschinenfabrik Rein-hausen, SW version)

N Y - M

Loc SPS Local operation for complete logi-cal device

N N - O

EEHealth INS External equipment health N N - OEEName DPL External equipment name plate N N - OOpCntRs INC Operation counter resettable N N - OOpCnt INS Operation counter N N - OOpTmh INS Operation time N N - OControlsDiag SPC Run diagnostics N N - OLEDRs SPC LED reset N N T O

Table 4: IEC 61850 data points (LLNO - Logical node)

5

5.1

5 Data points


LPHD class (LPHD1) - Physical deviceLPHD class (LPHD1)

Attributename

Attributetype


Used T M/O

PhyNam DPL Physical device name plateDevice information (manufactur-er=Maschinenfabrik Reinhausen,HW version, SW version, serialnumber, model, location)

N Y - M

PhyHealth INS Physical device healthOperational state of node (1=OK,2=warning, 3=error)

N Y - M

OutOv SPS Output communications bufferoverflow

N N - O

Proxy SPS LN is a proxyIndicates, if this logical node isworking as proxy, i.e. representinganother physical device

N Y - M

InOv SPS Input communications buffer over-flow

N N - O

NumPwrUp INS Number of power ups N N - OWrmStr INS Number of warm starts N N - OWacTrg INS Number of watchdog device re-

sets detectedN N - O

PwrUp SPS Power up detected N N - OPwrDn SPS Power down detected N N - OPwrSupAlm SPS External power supply alarm N N - ORsStat SPC Reset device statistics N N T O

Table 5: IEC 61850 data points (LPHD - Physical device)

YLTC1 - On-load tap-changer control/monitoring (optional)Attributename

Attributetype


used T M/O



N Y - M

Beh Beh BehaviorBehavior (e.g. enabled, disabled,blocked, test, test/blocked)

N Y - M

Health Health HealthOperational state of node (1=OK,2=warning, 3=error)

N Y - M

5.2

5.3

5 Data points


Attributename

Attributetype


used T M/O

NamPlt LPL Name plateManufacturer information (manu-facturer=Maschinenfabrik Rein-hausen, SW version)

N Y - M

Loc SPS Local operation N N - OEEHealth INS External equipment health N N - OEEName DPL External equipment name plate N N - OOpCntRs INC Operation counter resettable N N - OOpCnt INS Operation counter

Absolute amount of tap changeoperations

N Y - O

OpTmh INS Operation time N N - OMeasured valuesTorq MV Drive torque N N - OMotDrvA MV Motor drive current N N - OControlsTapPos ISC Change tap position to dedicated

positionN N - C

TapChg BSC Change tap positionRaise or lower tap changer posi-tion (e.g. 00=stop, 01=lower,10=raise)

N Y - C

Status informationEndPosR SPS End position raise reached

OLTC is in maximum tap positionor above

N Y - M

EndPosL SPS End position lower reachedOLTC is in minimum tap positionor below

N Y - M

OilFil SPS Oil filtration N N - OExtra attributesMotDrv SPS Motor-drive unit lowering/raising

tap positionIndication of active motor-driverunning contact

Y Y - O

SigGRE SPS Signal greenNo yellow or red events are pend-ing

Y Y - O

SigYEL SPS Signal yellowOne or more yellow events arepending

Y Y - O

5 Data points


Attributename

Attributetype


used T M/O

SigRED SPS Signal redOne or more red events are pend-ing

Y Y - O

USigYEL SPS User signal yellowOne or more yellow user/on-siteevents are pending

Y Y - O

USigRED SPS User signal redOne or more red user/on-siteevents are pending

Y Y - O

AbrPrts MV Percentage abrasion partsPercentage value for mainte-nance status of abrasion parts(diverter switch, tap selector, gen-eral parts)

Y Y - O

OilExCl MV Percentage oil exchange andcleaningPercentage value for status of oilchange and oil filter change

Y Y - O

AbsWPt MV Percentage absolute wear pointPercentage value for status ofcontact wear (only with OILTAP®on-load tap-changer types)

Y Y - O

OilSamp MV Percentage oil samplingPercentage value for status of oilsampling

Y Y - O

OnSTmintv MV Percentage on-site time-intervalPercentage value for status of on-site time interval and tap-changeoperation interval

Y Y - O

Table 6: YLTC1

SLTC1 - On-load tap-changer monitoringAttribute

nameAttribute

typeExplanation Extra at-

tributeused T M/O



N Y - M


N Y - M

5.4

5 Data points


Attributename

Attributetype


used T M/O

Health INS Health1:=OK; 3:= internal communicationfailure

N Y - M

NamPlt LPL Name plateVendor information of LTC Super-vision Monitoring (manufactur-er=Maschinenfabrik Reinhausen)

N Y - M

EEHealth INS External equipment health N N - OEEName DPL External equipment name plate N N - OLoc SPS Local operation N N - OOpCntRs INC Operation counter resettable N N - OOpCnt INS Operation counter N N - OMeasured valuesAbrPrt MV Absolute contact wear in % N Y - ODfAbrPrt MV Difference contact wear in % Y Y - OCuTmp MV ED housing temperature

Inner temperature in Celsius ofmotor-drive unit

Y Y - O

EnvTmp MV Environmental temperatureAmbient temperature in Celsiusoutside of motor-drive unit

Y Y - O

SelTmp MV Selector switch temperatureTemperature in Celsius of trans-former oil

Y Y - O

SelATmp MV Selector A oil temperatureTemperature in Celsius of first se-lector oil (in case of monitoring of 3separate OLTCs)

Y Y - O

SelBTmp MV Selector B oil temperatureTemperature in Celsius of secondselector oil (in case of monitoringof 3 separate OLTCs)

Y Y - O

SelCTmp MV Selector C oil temperatureTemperature in Celsius of third se-lector oil (in case of monitoring of 3separate OLTCs)

Y Y - O

DivTmp MV Diverter switch temperatureTemperature in Celsius of the(first) diverter switch oil compart-ment

Y Y - O

5 Data points


Attributename

Attributetype


used T M/O

DivBTmp MV Diverter switch B temperatureTemperature in Celsius of the sec-ond diverter switch oil compart-ment (in case of monitoring of 3separate OLTCs)

Y Y - O

DivCTmp MV Diverter switch C temperatureTemperature in Celsius of the thirddiverter switch oil compartment (incase of monitoring of 3 separateOLTCs)

Y Y - O

Status informationIntIn INS Integer status input N N - OAlm SPS General single alarm N N - OInd SPS General indication (binary input) N N - OExtra Attributes-AbrPrtFc INS Contact wear forecast date for

100%Forecast date when the contactwear will have reached 100%. Thedate value equates to the numberof days since the first of March2000.

Y Y - O

OilExCFc INS Oil exchange and cleaning fore-cast in days left to 100%Forecast date when the oil ex-change and cleaning or oil filterchange maintenance will havereached 100%. The date valueequates to the number of dayssince the first of March 2000.

Y Y - O

AbsWPtFc INS Abrasions part forecast for 100%Forecast date when the mainte-nance of abrasion parts will havereached 100%. The date valueequates to the number of dayssince the first of March 2000

Y Y - O

OilSmpFc INS Oil sample forecast in days left to100%Forecast date when the mainte-nance of oil sample will havereached 100%. The date valueequates to the number of dayssince the first of March 2000.

Y Y - O

5 Data points


Attributename

Attributetype


used T M/O

EvPrt1 INS Event signaling part 1Event bit 0 - 15 (16 bit value forstatus of respective event number:0:= event deactivated; 1:= eventactivated)

Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O

EvPrt8 INS Event signaling part 8Event bit 112 - 127 (16 bit valuefor status of respective event num-ber: 0:= event deactivated; 1:=event activated)

Y Y - O


Y Y - O

5 Data points


Attributename

Attributetype


used T M/O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O

DfAbrPrt MV Differential abrasion (in %) of partssubject to wear

Y Y - O

Table 7: SLTC1

GGIO1 - Generic process I/OAttribute

nameAttribute


tributeUsed T M/O

Common logical node information

5.5

5 Data points


Attributename

Attributetype


Used T M/O

Mod INC ModeMode/status (e.g. enabled, disa-bled, blocked, test, test/blocked)

N Y - M


N Y - M


N Y - M

NamPlt LPL Name plateManufacturer information (manu-facturer=Maschinenfabrik Rein-hausen)

N Y - M

EEHealth INS External equipment health N N - OEEName DPL External equipment name plate N N - OLoc SPS Local operation N N - OOpCntRs INC Operation counter resettable N N - OOpCnt INS Operation counter N N - OMeasured valuesAnIn MV Analog input N N - OControlsSPCSO SPC Single point controllable status

outputN N - O

DPCSO DPC Double point controllable statusoutput

N N - O

ISCSO INC Integer status controllable statusoutput

N N - O

Status informationIntIn INS Integer status input N N - OAlm SPS General single alarm N N - OInd SPS General indication (binary input) N N - OExtra attributesInd1 SPS IO X1:31

Input status of IO card input X1:31Y Y - O

Ind2 SPS IO X1:33Input status of IO card input X1:33

Y Y - O

Table 8: GGIO1

5 Data points



nameAttribute


tributeUsed T M/O



N Y - M


N Y - M


N Y - M


N Y - M


outputN N - O


N N - O


N N - O

Status informationIntIn INS Integer status input N N - OAlm SPS General single alarm N N - OInd SPS General indication (binary input) N N - OExtra attributesInd1 SPS UC1 X1:11

Input status of UC1 card inputX1:11

Y Y - O

Ind2 SPS UC1 X1:12Input status of UC1 card inputX1:12

Y Y - O

5.6

5 Data points


Attributename

Attributetype


Used T M/O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O

Table 9: GGIO2


nameAttribute


tributeUsed T M/O



N Y - M


N Y - M


N Y - M

5.7

5 Data points


Attributename

Attributetype


Used T M/O


N Y - M


outputN N - O


N N - O


N N - O



Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O

5 Data points


Attributename

Attributetype


Used T M/O


Y Y - O


Y Y - O


Y Y - O


Y Y - O

Table 10: GGIO3


nameAttribute


tributeUsed T M/O



N Y - M


N Y - M


N Y - M


N Y - M


outputN N - O

5.8

5 Data points


Attributename

Attributetype


Used T M/O


N N - O


N N - O



Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O


Y Y - O

Table 11: GGIO4

MR worldwideAustraliaReinhausen Australia Pty. Ltd.17/20-22 St Albans RoadKingsgrove NSW 2208Phone: +61 2 9502 2202Fax: +61 2 9502 2224E-Mail: [email protected]

BrazilMR do Brasil Indústria Mecánica Ltda.Av. Elias Yazbek, 465CEP: 06803-000Embu - São PauloPhone: +55 11 4785 2150Fax: +55 11 4785 2185E-Mail: [email protected]

CanadaReinhausen Canada Inc.3755, rue Java, Suite 180Brossard, Québec J4Y 0E4Phone: +1 514 370 5377Fax: +1 450 659 3092E-Mail: [email protected] IndiaEasun-MR Tap Changers Ltd.612, CTH RoadTiruninravur, Chennai 602 024Phone: +91 44 26300883Fax: +91 44 26390881E-Mail: [email protected] IndonesiaPt. Reinhausen IndonesiaGerman Center, Suite 6310,Jl. Kapt. Subijanto Dj.BSD City, TangerangPhone: +62 21 5315-3183Fax: +62 21 5315-3184E-Mail: [email protected]

IranIran Transfo After Sales Services Co.Zanjan, Industrial Township No. 1 (Aliabad)Corner of Morad Str.Postal Code 4533144551E-Mail: [email protected] ItalyReinhausen Italia S.r.l.Via Alserio, 1620159 MilanoPhone: +39 02 6943471Fax: +39 02 69434766E-Mail: [email protected] JapanMR Japan CorporationGerman Industry Park1-18-2 Hakusan, Midori-kuYokohama 226-0006Phone: +81 45 929 5728Fax: +81 45 929 5741 LuxembourgReinhausen Luxembourg S.A.72, Rue de PrésL-7333 SteinselPhone: +352 27 3347 1Fax: +352 27 3347 99E-Mail: [email protected]

MalaysiaReinhausen Asia-Pacific Sdn. BhdLevel 11 Chulan TowerNo. 3 Jalan Conlay50450 Kuala LumpurPhone: +60 3 2142 6481Fax: +60 3 2142 6422E-Mail: [email protected]

P.R.C. (China)MR China Ltd. (MRT)开德贸易（上海）有限公司

中国上海浦东新区浦东南路 360 号

新上海国际大厦 4楼 E座

邮编： 200120

电话：＋ 86 21 61634588

传真：＋ 86 21 61634582

邮箱：[email protected]

[email protected]

Russian FederationOOO MRNaberezhnaya Akademika Tupoleva15, Bld. 2 ("Tupolev Plaza")105005 MoscowPhone: +7 495 980 89 67Fax: +7 495 980 89 67E-Mail: [email protected]

South AfricaReinhausen South Africa (Pty) Ltd.No. 15, Third Street, Booysens ReserveJohannesburgPhone: +27 11 8352077Fax: +27 11 8353806E-Mail: [email protected] South KoreaReinhausen Korea Ltd.21st floor, Standard Chartered Bank Bldg.,47, Chongro, Chongro-gu,Seoul 110-702Phone: +82 2 767 4909Fax: +82 2 736 0049E-Mail: [email protected]

U.S.A.Reinhausen Manufacturing Inc.2549 North 9th AvenueHumboldt, TN 38343Phone: +1 731 784 7681Fax: +1 731 784 7682E-Mail: [email protected] United Arab EmiratesReinhausen Middle East FZEDubai Airport Freezone, Building Phase 63rd floor, Office No. 6EB, 341 DubaiPhone: +971 4 2368 451Fax: +971 4 2368 225Email: [email protected]

Maschinenfabrik Reinhausen GmbHFalkensteinstrasse 893059 Regensburg

+49 (0)941 4090-0+49(0)941 [email protected]

www.reinhausen.com

3547308/00 EN ▪ 07/13 ▪

Documents

Monitoring System TAPGUARD® 260 - Reinhausen · 2013. 8. 8. · LPHD class (LPHD1) - Physical device LPHD class (LPHD1) Attribute name Attribute type Explanation Extra at-tribute