Upload
others
View
20
Download
0
Embed Size (px)
Citation preview
PAGE 1 OF 14For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19
WIFI CONNECT Enjoy the convenience and freedom of wirelessly controlling functions from your smartphone
LED LIGHTING Light columns in the freezer and fresh food compartments extend the full length of the interior and LED lighting located inside the vegetable and climate-control drawers illuminate contents without compromising space
COLOR-MATCHED DISPENSER WITH PROXIMITY SENSOR Designed to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when
GE® WATER FILTER Has been moved from the fresh food compartment to the overhead cabinet, where it is discreetly out of sight
DELI DRAWER ON FULL-EXTENSION SLIDES Keeps meats, cheeses and other everyday foods within easy reach
SEALED VEGETABLE DRAWER Helps preserve the freshness of foods
ADJUSTABLE GLASS SHELVES Easily accommodate party trays and platters
GALLON-SIZE DOOR BIN Holds milk containers, two-liter bottles and pitchers
ADJUSTABLE DOOR BINS Can be moved to one of two positions in seven locations
DAIRY BIN WITH CENTER DIVIDER Has a unique magnetic seal that locks in freshness
FILTER-CHANGE INDICATOR LIGHT Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser
SABBATH MODE Designed to disable functions in accordance with Sabbath-observing practice
MONOGRAM 48" BUILT-IN SIDE-BY-SIDE REFRIGERATORZISB480DN
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19
STANDARD INSTALLATION
SECTION 2
SECTION 1
FLUSH INSET INSTALLATION
PAGE 2 OF 14
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
For questions about your appliance, please call 1-800-626-2000.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.
OVERALL DIMENSIONS
Product Specification Created 10/19PAGE 3 OF 14
SPECIFICATIONS
Overall Width 48" (121.92 cm)
Overall Height 84" (213.36 cm)
Overall Depth 25 3/8" (64.453 cm)
Door Clearance 28 5/8" (72.1 cm)
Cutout Width 47 1/2" (120.7 cm)
Cutout Height 83 1/2" - 84 1/2" (212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight 775 lb
*84"(213.4)
48" (121.9)
25 1/2" (64.8)
23 1/2" (59.7)
*72 1/4"(183.5)
*83 1/2"(212.1)
47" (119.4)Case width
28 5/8"(72.7)
TOP VIEW
*40"(101.6)
68 1/2"(174.0)
*3 3/4"(9.5)
ZISB480DX
SIDE VIEWFRONT VIEW* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height.
** Allow 4 9/16" (11.6) min clearance to a wall for 90˚
door swing
** Allow 4 9/16" (11.6) min clearance to a wall for 90˚
door swing
** These refrigerators are equipped with a 3-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow full 130° door swings for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted. Dimensions based on custom handle height of 2 9/16" (6.5).
Allow **15" (38.1) min clearance for 130˚ door swing
Allow **20" (50.8) min clearance for 90˚ door swing
ATTENTION ELECTRICIAN:A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
STANDARD INSTALLATION
PAGE 4 OF 14
STANDARD INSTALLATIONZISB480DH
24" (61)
1 9/16"(3.97)
47 1/2" (120.7)7/16" (1.1)Trim overlap
3 1/2"(8.9)
3 1/2"(8.9)
75"(190.5 )
From floorto bottom
of electricalarea
*84 1/2"(214.6)
*Trim will overlapadditional 7/16"
SIDE VIEW FRONT VIEW
TOP VIEW
5"(12.7)
5"(12.7)
WATERW
6"(15.24)
20" (50.8)
5"(12.7)
E
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19
STANDARD INSTALLATIONSTANDARD INSTALLATION
ANTI-TIP BRACKET
FRONT VIEW SIDE VIEWW
24" (61.0)
1 1/2"(3.8)
3 1/4"(8.3) 7/16" (1.1)
Trim overlap
3 1/2"(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min*84 1/2" max
(212.1-214.6)*Trim will overlapadditional 7/16"
3 1/2"(8.9)
75"(190.5 )
From floorto bottom
of electricalarea
6"(15.2)
5"(12.7)
5"(12.7)
5"(12.7)
ZISB480DX
SIDE VIEW INSTALLEDUNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLEDWITH WOODEN WALL STUDS
AND NO SOFFIT
*84"(213.4)
*Or installationheight from floor
2" x 4"Cut to 35" Length
Screws mountedinto vertical wall
studs
FRONT VIEW INSTALLEDWITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"Min.
Side View TopCase Trim
Install ScrewsThrough Trim and Into3/4" Min. Wood Brace
D
C
E
A
B
A Mounting the junction box in this location will also allow for front accessibility through access panel.
B Water supply area.
WARNING:The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.
Determine your installation construction and required anti-tip configuration:
C Installed Under Soffit After installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exceed 24" deep. The top case trim overlaps the bottom of the soffit.
D Wooden Wall Studs and No Soffit • Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of opening at 84" or your installation height from the floor.
E Metal Wall Studs and No Soffit This method requires securely fastened cabinets on both sides and a 3/4" minimum wood brace above unit, with it’s front surface 24" from back wall. • After installing unit into opening,
raise grille panel and attach metal case top trim to 3/4" minimum wood brace.
• The brace spanning the enclosure must be securely fastened to cabinets on both sides.
See Installation Instructions for detailed instructions.
The refrigerator will project forward, slightly beyond adjacent cabinetry.
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19
STANDARD INSTALLATION
PAGE 5 OF 14
CUSTOM SIDE PANELS
F
2 9/16"(6.5)
*3"- 4"(7.6 - 10.2)
*Dependingon installation
height
1 7/8"(4.8)
24" (61.0)
3/16"(.5)
*84"(213.4)
*Dependingon installation
height
ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRHZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
F Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19
STANDARD INSTALLATION
PAGE 6 OF 14
PANEL ASSEMBLY CROSS SECTION
Door1/4" Backer Panel
.10" Spacer Panel
Optional ZKLN kit handles
Trim
3/4" Overlay Panel
3/4" OVERLAY PANEL DIMENSIONS
1/4" FRAMED PANEL DIMENSIONS
Door
1/4" Framed PanelOptional ZKLN kit handles
Trim
PANEL ASSEMBLY CROSS SECTION
A B C D E1/4" Backer Panel 45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16"
.10" Spacer Panel 45" 8 5/8" 67" 17 1/4" 25 1/4"
3/4" Overlay Panel 46 1/8" 9 3/4" 68 5/8" 18 13/16" 26 13/16"
A B C D E1/4" Framed Panel 45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16"
Grille Panel
FreezerPanel
DispenserCutout
FreshFoodPanel
A
B
C
F
G
D E
Grille Panel
FreezerPanel
DispenserCutout
FreshFoodPanel
A
B
C
F
G
D E
F G34 3/16" 3 7/8"
DISPENSER CUTOUT POSITION
PANEL DIMENSIONS
DispenserCutout
11"(27.9)
13 5/16"(33.8)
F G34 5/16" 4"
.25" + .10" + .75" = 1.10" Total Panel Thickness
PANEL DIMENSIONS
* DISPENSER CUTOUT POSITION
* Cut the dispenser opening after the backer, spacer and overlay panels have been assembled.
DispenserCutout
11"(27.9)
13 5/16"(33.8)
3/4" OVERLAY PANELS: For 3/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim.
The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.
Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
MAXIMUM TOTAL PANEL WEIGHT: • Fresh food door panel – 75 lbs. • Freezer drawer panel – 53 lbs. • Grille panel – 18 lbs
Door handles not included. Custom handles supplied by your cabinet maker may be used. Optional visor handle kit ZKLN is available. Kit includes two handles.
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.
1/4" FRAMED PANELS: For 1/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim.
MAXIMUM TOTAL PANEL WEIGHT: • Fresh food door panel – 75 lbs. • Freezer drawer panel – 53 lbs. • Grille panel – 18 lbs
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19
STANDARD INSTALLATION
PAGE 7 OF 14
DISPENSER TRIM
RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS
1/4" PANEL DISPENSER TRIM 3/4" OVERLAY PANEL DISPENSER TRIM
Freezer Door1/4" Framed Panel
Ice/Water Dispenser
1/4"Total
ThicknessFreezer Door1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
Ice/Water Dispenser
1.10"Total
Thickness
A B
14"
11 3/4"
1/4" Backer Panel
3/4" Overlay Panel.10" Spacer
1.10"Total
ThicknessDC
DISPENSER TRIM SIDE VIEW CROSS SECTION
(SHOWING RAISED OVERLAY WITH MIDDLE RAIL)
These refrigerators are supplied with two dispenser trims, one for framed panels and one for overlay panels.
1/4" PANEL DISPENSER TRIM: The framed panel must be 1/4" nominal thickness to fit the dispenser trim.
• The dispenser trim fits over the custom panel and snaps into the freezer door.
• If the panel is less than 0.250" thick, a noticeable gap may be created around the dispenser trim. Foam tape may be applied on the door to improve the fit.
• If the panel is more than 0.250" thick, the dispenser trim cannot be secured to the door.
3/4" OVERLAY PANEL DISPENSER TRIM: The 3/4" overlay dispenser trim is designed to fit a total panel thickness of 1.100".
• If the panel is less than 1.100" thick, a noticeable gap may be created around the dispenser trim.
• If the panel is more than 1.100" thick, the dispenser trim cannot be secured to the door.
• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.
• Alternative panel construction methods such as securing a 3/4" panel to a 1/4" backer panel cannot be used. Another method, routing a 3/4"-thick panel on all sides, cannot be used. These methods will not result in the required 1.100" panel thickness.
• When a raised panel design is to be used, a custom middle rail is required.
RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS: When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.
• The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.
• The middle rail must be 1.10" total thickness to accept the dispenser trim.
For questions about your appliance, please call 1-800-626-2000.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.
Product Specification Created 10/19PAGE 8 OF 14
SPECIFICATIONS
Overall Width 50" (127.0 cm)†
Overall Height 84 1/2" (214.6 cm) †
Overall Depth 26" (66.0 cm) †
Door Clearance 28 5/8" (72.1 cm)
Cutout Width 51" (129.5 cm)
Cutout Height 85" (215.9 cm)
Cutout Depth 26 3/16" (66.5 cm)
Plumbing Requirements 1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight 775 lb (351.5 kg)
50" (127.0)
84 1/2"(214.6)
72 5/8"(184.5)
68 5/8"(174.3)
ZISB480DH
FRONT VIEW
11 11/16"(29.7)
26" (66.0)
4"(10.2) SIDE VIEW
* 83 1/2"(212.1)
15 3/8"(39.1)
*39 17/32"(100.4)
47" (119.4)Case width
28 5/8"(72.7)
TOP VIEW
Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84”
** These refrigerators are equipped with a 3-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted. A 130° door swing optionis available for standard installation only. Dimensions based on custom handle heightof 2-9/16” (6.5).
** Allow 4 9/16" (11.6) min clearance to a wall for 90˚
door swing
** Allow 4 9/16" (11.6) min clearance to a wall for 90˚
door swing
Allow **13" (33.0) min clearance for door swing
Allow **20" (50.8) min clearance for door swing
20 5/8" (52.4)
20 5/8"(52.4)
*115° Door swing
Doors can be adjusted to 90° door swing
OVERALL DIMENSIONS AFTER PANEL INSTALL
FLUSH INSET INSTALLATION
† Dimensions include 3/4" custom cabinet panel
ATTENTION ELECTRICIAN:A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19
FLUSH INSET INSTALLATION
PAGE 9 OF 14
FLUSH INSET INSTALLATION 3/4" PANELS
E
FLUSH INSTALLATIONZISB480DH
51" (129.5) Flush inset width
49 1/2" (125.7)Width between cleats
7"(17.8)
7"(17.8)
3/4" (1.9)Width of side cleats
5 1/4" (13.3)
1/2" (1.3)26 3/16" (66.5)Flush inset depth
20 15/16" (53.2)Depth to cleat
FRONT VIEWSIDE VIEW
TOP VIEW
WATER3 1/2"
(8.9)W
Finished cleats
Finished cleats
Case Trim
3/4" Panel
Case
Door
6"(15.2)
22 1/4"(56.5)
5"(12.7)
3 1/2"(8.9)
75"(190.5 )
From floorto bottom
of electricalarea
85"(215.9)
85"(215.9)
A
B
ANTI-TIP BRACKET
FRONT VIEW SIDE VIEWW
24" (61.0)
1 1/2"(3.8)
3 1/4"(8.3) 7/16" (1.1)
Trim overlap
3 1/2"(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min*84 1/2" max
(212.1-214.6)*Trim will overlapadditional 7/16"
3 1/2"(8.9)
75"(190.5 )
From floorto bottom
of electricalarea
6"(15.2)
5"(12.7)
5"(12.7)
5"(12.7)
ZISB480DX
SIDE VIEW INSTALLEDUNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLEDWITH WOODEN WALL STUDS
AND NO SOFFIT
*84"(213.4)
*Or installationheight from floor
2" x 4"Cut to 35" Length
Screws mountedinto vertical wall
studs
D
C
A Mounting the junction box in this location will also allow for front accessibility through access panel.
B Water supply area.
WARNING:The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.
Determine your installation construction and required anti-tip configuration:
C Cut a 1" x 4" block 35" long. Measure and mark under the soffit, 5 1/4" from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84".
D Wooden Wall Studs and No Soffit • Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of opening at 84" or your installation height from the floor.
See Installation Instructions for detailed instructions.
FLUSH INSET KIT ZKFN REQUIRED
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19PAGE 10 OF 14
FLUSH INSET INSTALLATION 1/2" PANELS
E
FLUSH INSTALLATIONZISB480DH
51" (129.5) Flush inset width
49 1/2" (125.7)Width between cleats
7"(17.8)
7"(17.8)
3/4" (1.9)Width of side cleats
5 3/8" (13.7)
1/2" (1.3)26 3/16" (66.5)Flush inset depth
20 13/16" (52.9)Depth to cleat
FRONT VIEWSIDE VIEW
TOP VIEW
WATER3 1/2"
(8.9)W
Finished cleats
Finished cleats
Case Trim
1/2" Panel
Case
Door
6"(15.2)
22 1/4"(56.5)
5"(12.7)
3 1/2"(8.9)
75"(190.5 )
From floorto bottom
of electricalarea
85"(215.9)
85"(215.9)
A
B
ANTI-TIP BRACKET
FRONT VIEW SIDE VIEWW
24" (61.0)
1 1/2"(3.8)
3 1/4"(8.3) 7/16" (1.1)
Trim overlap
3 1/2"(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min*84 1/2" max
(212.1-214.6)*Trim will overlapadditional 7/16"
3 1/2"(8.9)
75"(190.5 )
From floorto bottom
of electricalarea
6"(15.2)
5"(12.7)
5"(12.7)
5"(12.7)
ZISB480DX
SIDE VIEW INSTALLEDUNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLEDWITH WOODEN WALL STUDS
AND NO SOFFIT
*84"(213.4)
*Or installationheight from floor
2" x 4"Cut to 35" Length
Screws mountedinto vertical wall
studs
D
C
A Mounting the junction box in this location will also allow for front accessibility through access panel.
B Water supply area.
WARNING:The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.
Determine your installation construction and required anti-tip configuration:
C Cut a 1" x 4" block 35" long. Measure and mark under the soffit, 5 3/8" from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84".
D Wooden Wall Studs and No Soffit • Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of opening at 84" or your installation height from the floor.
See Installation Instructions for detailed instructions.
FLUSH INSET KIT ZKFN REQUIRED
FLUSH INSET INSTALLATION
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19PAGE 11 OF 14
A B C D E50" 11 3/16" 68 5/8" 20 7/8" 28 7/8"
PANEL DIMENSIONS
FLUSH INSET 3/4" PANEL DIMENSIONS
F G34 9/32" 5 15/16"
DISPENSER CUTOUT POSITIONDispenser
Cutout
11"(27.9)
13 5/16"(33.8)
3/4" RAISED DOOR PANEL ROUTING
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW(AFTER ROUTING)
Front
NOTE: Routed areas should be finished as they may be visible when assembled.
CORNER VIEW SHOWING“PICTURE FRAME” ROUTING
Back
HINGESIDE
HANDLESIDE
Front
Back
3/4" PANEL BOTTOM VIEW(AFTER ROUTING)
3/4"
11/32"1/4"
3/16"
1/4" 7/16"
DETAIL TOP
DETAIL BOTTOM
2 1/16" 3/16"
ROUTER DEPTH 1/4"
DETAIL HINGESIDE
DETAIL HANDLESIDE
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame” routing allowing the panels to slide into the attached door and grille trims.
MAXIMUM TOTAL PANEL WEIGHT: • Fresh food door panels – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs.
DOOR HANDLES Door handle not included. A custom handle supplied by your cabinet maker may be used.
WARNING:Door Trim Pinch Point
Hazard Improper installation can lead to a finger pinch point hazard between the side door trim and the cabinets when operating the door, especially with children. To minimize this risk you must follow the installation instructions for cabinet dimensions, trim assembly and door stop angle.
FLUSH INSET INSTALLATION
Grille Panel
FreezerPanel
DispenserCutout
FreshFoodPanel
A
B
C
F
G
D E
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19
STANDARD INSTALLATION
PAGE 12 OF 14
HELPFUL TIPSTrimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame” routing allowing the panels to slide into the attached door and grille trims.
MAXIMUM TOTAL PANEL WEIGHT: • Fresh food door panels – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs.
DOOR HANDLES Door handle not included. A custom handle supplied by your cabinet maker may be used.
FLUSH INSET INSTALLATION3/4" RAISED GRILLE PANEL ROUTING
Front
NOTE: Routed areas should be finished as they may be visible when assembled.
CORNER VIEW SHOWING“PICTURE FRAME” ROUTING
Back
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW(AFTER ROUTING)
3/16"
DETAIL TOP
DETAIL BOTTOM
RO
UTER
DEPTH
1/4"
2"
2 1/16" 2 1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
DETAIL LEFT SIDE
DETAIL RIGHTSIDE
3/4" PANEL BOTTOM VIEW(AFTER ROUTING)
LEFTSIDE
RIGHTSIDE
Front
Back
FLUSH INSET INSTALLATION
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19PAGE 13 OF 14
DISPENSER TRIM
RAISED PANEL DESIGN ON DISPENSER MODELS
3/4" OVERLAY PANEL DISPENS-ER TRIM
1/2" OVERLAY PANEL DIS-PENSER TRIM
A
14"
11 3/4"
DISPENSER TRIM SIDE VIEW CROSS SECTION
(SHOWING RAISED PANEL WITH MIDDLE RAIL)
Freezer Door
3/4" Flush Panel
Ice/Water Dispenser
Freezer Door1/4" Backer Panel.10" Spacer Panel
1/2" Overlay Panel
Ice/Water Dispenser
.85"Total
Thickness
3/4" or 1/2" Flush Panel
3/4" or .85"Total
ThicknessCB
These refrigerators are supplied with a dispenser trim for flush inset panels.
A PANEL DISPENSER TRIM: The provided dispenser trim is designed to fit a total panel thickness of 3/4" or 0.85".
• If the panel is less than 3/4" thick, a noticeable gap may be created around the dispenser trim.
• If the panel is more than 0.85" thick, the dispenser trim cannot be secured to the door.
• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.
• When a raised panel design is to be used, a custom middle rail is required.
RAISED PANEL DESIGN ON DISPENSER MODELS: When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.
B The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.
C The middle rail must be 3/4" total thickness for 3/4" panels or 0.85" total thickness for 1/2" panels to accept the dispenser trim.
FLUSH INSET INSTALLATION
HELPFUL TIPS
For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19PAGE 14 OF 14
A B C DFresh Food Panel 2 1/16" 1/4" 1/8" 1/8"
Freezer Panel 2 1/16" 1/4" 1/8" 1/8"
Grille Panel 2 1/16" 2 1/16" 1 15/32" 7/32"
PANEL DIMENSIONS
PANEL DIMENSIONS
FLUSH INSET 1/2" PANEL DIMENSIONS
1/4" BACKER ASSEMBLY ROUTING DIMENSIONS
FreezerBack
Hinge Side
Fresh FoodBack
Backer with Overlay Panel Assembly
A AB B
C C
D D
1/2"OverlayPanel
1/4"BackerPanel
Door
.10"Spacer
C
DA B
Grille Back
F G34 15/16" 5 5/16"
DISPENSER CUTOUT POSITIONDispenser
Cutout
11"(27.9)
13 5/16"(33.8)
A B C D E1/4" Backer Panel 45 7/8" 9 1/2" 68 3/8" 18 9/16" 29 9/16"
.10" Space Panel 45" 8 5/8" 67" 17 9/16" 25 9/16"
1/2" Overlay Panel 50" 11 3/16" 68 5/8" 20 7/8" 28 7/8"
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.
ASSEMBLE THE PANELS WITH GLUE AND SCREWS: • Center the spacer panel on the
backer panel, left to right and top to bottom. Secure the panels with glue.
• Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel.
MAXIMUM TOTAL PANEL WEIGHT: • Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs.
Grille Panel
FreezerPanel
DispenserCutout
FreshFoodPanel
A
B
C
F
G
D E