Upload
buicong
View
218
Download
0
Embed Size (px)
Citation preview
Summary of the eight versions of KLINGER SWGs, the designprinciple,materialsand mountinginstructions.
KLINGER
Spiral Wound Gaskets
KLINGERmaxiflex mounting instructions
The principleThe KLINGERmaxiflex function isbased on the metal winding/ filler re-lationship and the flange surfaces.
The surface roughness should beapprox. Ra 3.2 µm. KLINGERmaxiflexgaskets can be used in flanges withlarger surface roughnesses, but in thiscase the bolt loads should be increa-sed so as to ensure proper function ofthe gasket.
When the KLINGERmaxiflex gas-ket is compressed during mounting,the homogeneous filler „flows“ intothe irregularities of the flange. Themetal windings enclose the filler and,at the same time, ensure the strengthand elasticity of the gasket.
If the gasket is equipped with anPTFE filler it must have an inner ringsince the PTFE permits no furthercompression, as is the case with otherfillers. On the one hand, it preventsthe gasket from springing open andon the other, penetration of the flo-wing PTFE in the pipeline. The largerthe surface roughnesses in the flangesurface, the larger the surface loadrequired to permit a flow of the PTFEin the irregularities.
MountingThe bolts should be free of damageand lubricated with high-temperatureresistant greases before mounting.
Insert the gasket and fasten boltsfinger-tight.
Next, tighten the bolts crosswise(see sketch) in at least 3 to 4 passes.The more passes you perform, themore uniform the force which is intro-duced into the flange-gasket system.
In the last pass, the bolts must betightened only clockwise.
1
2
34
7 5
86
All information is provided inaccordance with the current state ofknowledge. As we cannot influence thespecific application conditions, wewould ask you to consider this as anon-binding recommendation.
We can assume no liability for anyresulting damage.
We reserve the right to technicalmodifications.
MountingFlange surface condition:1. metallically clean2. plane-parallel3. dry4. fat freeDo not use separating agents or sealing aids!
Certified Fire Safe According to API 6FB!
Wide choice of materials for metal strip and filler. Suitable for high pressures and temperatures.Recommended for flanges with tongue and groove.
Type R
Solid metal outer ring used as a centerring device and compressionstop.Used on raised face and flat face flanges.
Type CR
Solid metal inner ring.Use with high pressures and temperatures.Male to female flanges.
Type RIR
This gives the gasket recoveryforces which provide for a reliablesurface load even at fluctuating oper-ating conditions.
In the present 8 versions, thebasic element is added by innerand/or outer rings as needed.
Standard Metal strip materials Gasket thicknessesNominalthickness3.2 mm4.5 mm7.2 mm
Compressed Guide ringthickness thickness2.3 - 2.5 mm 2 - 2.2 mm3.2 - 3.4 mm 3 - 3.3 mm5.0 - 5.5 mm 5 - 5.5 mm
The design principle of theKLINGER Spiral-Wound GasketsThe basic element of every gasket isthe wound core. The V-shaped metalstrip is spirally wound with the soft-material filler.
To improve the mechanicalstrength and other sealing character-istics, some layers at the beginningand at the end are wound without softmaterial and spot-welded over thetotal circumference.
The constant tensile force duringthe complete winding process permitsa defined, constant thickness of thestructure.
1.43011.44011.44041.45411.4571Special version:Monel 400 ®, InConel 600 ®, InConel 625 ®, InConel X750 ®,Nickel 200 ®, Titanium, Incoloy 800 ®, Incoloy 825 ®
Other materials on request
304316316 L321316 Ti
Solid metal outer and inner rings.For use at high pressures and temperatures.Suitable for raised face or flat faceflanges.Prevents turbulences and protects the flanges from erosion.Protects the inner windings of thegasket element from high temperatures.
Solid metal outer ring, PTFE innerring.Suitable for raised face or flat faceflanges.PTFE inner ring acts as an additionalgasket and protects the inner windingsof the gasket element from the fluid.
Solid metal inner ring with KLINGER-graphite facing.For use at high pressures and temperatures.Suitable for raised face or flat faceflanges.Suitable for corrosive media.Graphite inner ring acts as an additional gasket.
Fillers and temperature limits CeramicsKLINGERgraphite*PTFENonas*pure graphite standard 98% purity or 99.85% nuclear grade
approx. 800°Capprox. 600°Capprox. 260°Capprox. 460°C
Standard materials outer ringCarbon steel,colour-powder coatedStainless steelacc. to the standard metal strip materials
Standard materials inner ringStainless steelacc. to the standard metal strip materials
KLINGERmaxiflex spiral-wound gaskets
KLINGERSpiral-Wound Gaskets
Type CRIR Type CRIR/PTFE inner ring
Type CRIR/KLINGERgraphite inner ring
Wide choice of materials for metal strip and filler. Suitable for high pressures and temperatures.Recommended for flanges with tongue and groove.
Type R
Solid metal outer ring used as a centerring device and compressionstop.Used on raised face and flat face flanges.
Type CR
Solid metal inner ring.Use with high pressures and temperatures.Male to female flanges.
Type RIR
This gives the gasket recoveryforces which provide for a reliablesurface load even at fluctuating oper-ating conditions.
In the present 8 versions, thebasic element is added by innerand/or outer rings as needed.
Standard Metal strip materials Gasket thicknessesNom.gasket thickness3.2 mm4.5 mm7.2 mm
Recommended thickness in loaded condition2.3 – 2.5 mm3.2 – 3.4 mm4.8 – 5.0 mm
The design principle of theKLINGERmaxiflex spiral-wound gasketsThe basic element of every gasket isthe wound core. The V-shaped metalstrip is spirally wound with the soft-material filler.
To improve the mechanicalstrength and other sealing character-istics, some layers at the beginningand at the end are wound without softmaterial and spot-welded over thetotal circumference.
The constant tensile force duringthe complete winding process permitsa defined, constant thickness of thestructure.
1.43011.44011.44041.45411.4571Special version:Monel 400 ®, InConel 600 ®, InConel 625 ®, InConel X750 ®,Nickel 200 ®, Titanium, Incoloy 800 ®, Incoloy 825 ®
Other materials on request
304316316 L321316 Ti
Solid metal outer and inner rings.For use at high pressures and temperatures.Suitable for raised face or flat faceflanges.Prevents turbulences and protects the flanges from erosion.Protects the inner windings of thegasket element from high temperatures.
Solid metal outer ring, PTFE innerring.Suitable for raised face or flat faceflanges.PTFE inner ring acts as an additionalgasket and protects the inner windingsof the gasket element from the fluid.
Solid metal inner ring with KLINGER-graphite facing.For use at high pressures and temperatures.Suitable for raised face or flat faceflanges.Suitable for corrosive media.Graphite inner ring acts as an additional gasket.
Fillers and temperature limits CeramicsKLINGERgraphite*PTFEMica*pure graphite standard 98% purity or 99.85% nuclear grade
approx. 800°Capprox. 500°Capprox. 260°Capprox. 900°C
Standard materials outer ringCarbon steel,colour-powder coatedStainless steelacc. to the standard metal strip materials
Standard materials inner ringStainless steelacc. to the standard metal strip materials
KLINGER Spiral-Wound Gaskets
KLINGERmaxiflex spiral-wound gaskets
Type CRIR Type CRIR/PTFE inner ring
Type CRIR/KLINGERgraphite inner ring
KLINGERSpiral-Wound Gaskets
Spiral wound sealing element. Wound high density.Wide choice of materials for metalstrip and filler material.For use in high-pressure pumps,high-pressure valves and gas applications.Low emission tested.
Type RHD
KLINGERgraphite facing 0.5 mm.For use in manhole gaskets.Suitable for use with low bolt loadsand uneven gasket surfaces.Double sealing effect.
Type R withKLINGERgraphite facing
Combined inner and outer rings.The inner ring could have pass barsor could carry either a metal clad orsoft gasket with pass bars.
Type HTX forheat exchan-gers
Recommended sealing strip roughnessThese gaskets are capable of givingan excellent seal over a wide range offlange surface finishes.
Subject to technical alterations. Status: April 1999
general critical vacuum
Ra micrometer3.2 – 5.13.22.0
(Larger flange surface finishes requirehigher bolt loads)
However, as a general guide werecommend the following:
PN10–4036404754657084102115140168196221251307358405458566666770874974
1,0781,2801,5101,7201,9202,1202,3302,5302,7302,9303,130
PN 64–32036404754657084104119144172200227257315366413466574674778882982
1,0861,290
–––––––––
d4
10465161718292
107127142162192217247272327377437488593695810917
1,0171,1241,3411,5481,7721,9722,1822,3842,5942,7943,0143,228
d3d2
10–320242833404954668295120146174195225286337382433537637737837930
1,0301,2301,4501,6601,8602,0502,2602,4602,6602,8603,060
KLINGERmaxiflextypes CR, CRIR
Suitable for flanges in accordance with DIN and BS 4504,measures in mm
DN
101520253240506580100125150175200250300350400500600700800900
1,0001,2001,4001,6001,8002,0002,2002,4002,6002,8003,000
d1
10–320182227344348577386
108134162183213267318363414518618718818910
1,0101,2101,4201,6301,8302,0202,2302,4302,6302,8303,030
16465161718292
107127142162192217247272328383443495617734804911
1,0111,1281,3421,5421,7641,9642,1682,378
––––
25465161718292
107127142167193223253283340400457514624731833942
1,0421,1541,3641,5781,7982,0002,230
–––––
40465161718292
107127142167193223265290352417474546628747852974
1,0841,1941,3981,6181,830
–––––––
645661748290
102112137147173210247277309364424486543657764879988
1,1081,2201,452
–––––––––
1005661748290
102118143153180217257287324391458512572704813
––––––––––––––
1605661748290
102118143153180217257284324388458––––––––––––––––––
25067727982100108123153170202242284316358442538––––––––––––––––––
d2d3d4
d4
d1d2d3
CR CRIR
Summary of the eight versions of KLINGERmaxiflex, the designprinciple,materialsand mount-ing instructions.
KLINGER-maxiflex
spiral-wound gaskets
Mounting Instructions
The principleThe spiral wound function isbased on the metal winding/ filler re-lationship and the flange surfaces.
The surface roughness should beapprox. Ra 3.2 µm. These gasketscan be used in flanges with largersurface roughnesses, but in thiscase the bolt loads should be increased so as to ensure proper function of the gasket.
When the gasket iscompressed during mounting,the homogeneous filler „flows“ intothe irregularities of the flange. Themetal windings enclose the filler and,at the same time, ensure the strengthand elasticity of the gasket.
If the gasket is equipped with aPTFE filler it must have an inner ringsince the PTFE permits no furthercompression, as is the case with otherfillers. On the one hand, it preventsthe gasket from springing open andon the other, penetration of the flo-wing PTFE in the pipeline. The largerthe surface roughnesses in the flangesurface, the larger the surface loadrequired to permit a flow of the PTFEin the irregularities.
MountingThe bolts should be free of damageand lubricated with high-temperatureresistant greases before mounting.
Insert the gasket and fasten boltsfinger-tight.
Next, tighten the bolts crosswise(see sketch) in at least 3 to 4 passes.The more passes you perform, themore uniform the force which is intro-duced into the flange-gasket system.
In the last pass, the bolts must betightened only clockwise.
1
2
34
7 5
86
All information is provided inaccordance with the current state ofknowledge. As we cannot influence thespecific application conditions, wewould ask you to consider this as anon-binding recommendation.
We can assume no liability for anyresulting damage.
KLINGER reserve the right to technical modifications.
MountingFlange surface condition:1. metallically clean2. plane-parallel3. dry4. fat freeDo not use separating agents or sealing aids!
d2d3d4
d4
d1d2d3
CR CRIR
10 –320
d1
10 –320
d2
PN 10 –40
d3
PN 64 –320
10 16 25 40 64d4
100 160 250DN
Subject to technical alterations.Status: April 1999
Certified according to DIN EN ISO 9001.
KLINGER SWGtypes CR/CRIR
Suitable for flanges in accordance with DIN and BS 4504,measures in mm
d2d3d4
d4
d1d2d3
CR CRIR
d2d3d4
d4
d1d2d3
CR CRIR
4.75
7 M
axifl
ex 9
5Pa
nton
e Blau
541
Pa
nton
e Rot
206
Subject to technical alterations.Status: October 2000
Certified according to DIN EN ISO 9001.
KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de
Subject to technical alterations.Status: October 2000
Certified according to DIN EN ISO 9001.
150300400600
9001,5002,500
150 300 400 600 900 1,500 2,500 150 300 400 600 900 1,500 2,500
øA ofsealing elem.
øIof sealing element
øAof centering ring
d3 d2 d4No
min
al w
idth
Pressure stage [lbs] Pressure stage [lbs]Press. st. [lbs]
KLINGER SWGtypes CR/CRIR
Gaskets in accordance with ASME B 16.20, flanges according ANSI B 16.5, measures in inch
Gaskets in accordance with ASME B 16.20, flanges according ANSI B 16.5, measures in mm
KLINGERmaxiflextypes CR/CRIR
150300400600
9001,5002,500
150 300 400 600 900 1,500 2,500 150 300 400 600 900 1,500 2,500
øA ofsealing elem.
øIof sealing element
øAof centering ring
d3 d2 d4
Nom
inal
wid
th
Pressure stage [lbs] Pressure stage [lbs]Press. st. [lbs]
d2d3d4
d4
d1d2d3
CR CRIR
d2d3d4
d4
d1d2d3
CR CRIR
4.75
7 M
axifl
ex 9
5Pa
nton
e Blau
541
Pa
nton
e Rot
206
KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de
Subject to technical alterations.Status: October 2000
Certified according to DIN EN ISO 9001.
Subject to technical alterations.Status: October 2000
Certified according to DIN EN ISO 9001.
150300400600
9001,5002,500
150 300 400 600 900 1,500 2,500 150 300 400 600 900 1,500 2,500
øA ofsealing elem.
øIof sealing element
øAof centering ring
d3 d2 d4
Nom
inal
wid
th
Pressure stage [lbs] Pressure stage [lbs]Press. st. [lbs]
KLINGERmaxiflextypes CR/CRIR
Gaskets in accordance with ASME B 16.20, flanges according ANSI B 16.5, measures in inch
Gaskets in accordance with ASME B 16.20, flanges according ANSI B 16.5, measures in mm
KLINGER SWGtypes CR/CRIR
150300400600
9001,5002,500
150 300 400 600 900 1,500 2,500 150 300 400 600 900 1,500 2,500
øA ofsealing elem.
øIof sealing element
øAof centering ring
d3 d2 d4No
min
al w
idth
Pressure stage [lbs] Pressure stage [lbs]Press. st. [lbs]
Inner-Ring Inside Diameters for Spiral-Wound Gaskets for Use With ASME B16.5 Flanges (as per ASME B16.20-2007 Standard's Table 12) Flange Pressure Class
Size (NPS) 150 300 400(Note 1) 600 900(Note 1) 1500 2500(note1)
1/2 14.2 14.2 14.2 14.2 14.2 14.2 14.2 3/4 20.6 20.6 20.6 20.6 20.6 20.6 20.6 1 26.9 26.9 26.9 26.9 26.9 26.9 26.9
1 1/4 38.1 38.1 38.1 38.1 33.3 33.3 33.3 1 1/2 44.5 44.5 44.5 44.5 41.4 41.4 41.4
2 55.6 55.6 55.6 55.6 52.3 52.3 52.3 2 1/2 66.5 66.5 66.5 66.5 63.5 63.5 63.5
3 81.0 81.0 81.0 81.0 78.7 78.7 78.7 4 106.4 106.4 102.6 102.6 102.6 97.8 97.8 5 131.8 131.8 128.3 128.3 128.3 124.5 124.5 6 157.2 157.2 154.9 154.9 154.9 147.3 147.3 8 215.9 215.9 205.7 205.7 196.9 196.9 196.9
10 268.2 268.2 255.3 255.3 246.1 246.1 246.1 12 317.5 317.5 307.3 307.3 292.1 292.1 292.1 14 349.3 349.3 342.9 342.9 320.8 320.8 … 16 400.1 400.1 389.9 389.9 374.7 368.3 … 18 449.3 449.3 438.2 438.2 425.5 425.5 … 20 500.1 500.1 489.0 489.0 482.6 476.3 … 24 603.3 603.3 590.6 590.6 590.6 577.9 …
Note 1: (1) There are no NPS 1/2 through NPS 3 Class 400 flanges (use Class 600) , NPS 1/2 through NPS 2 1/2 Class 900
flanges (use Class 1500), or NPS 14 and larger Class 2500 flanges.
subject to technical alterations. status: Oct'10
d2d3d4
d4
d1d2d3
CR CRIR
d2d3d4
d4
d1d2d3
CR CRIR
4.75
7 M
axifl
ex 9
5Pa
nton
e Blau
541
Pa
nton
e Rot
206
øI øI øA øAøI øI øA øAøI øI øA øAøI øI øA øA
Innerring
Sealing element
Cen-teringring
Innerring
Sealing element
Cen-teringring
Innerring
Sealing element
Cen-teringring
Sealing element
Cen-teringring
Innerring
Pressure stage [lbs]150
Pressure stage [lbs]300
Pressure stage [lbs]600
Pressure stage [lbs]900
d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4
KLINGER SWGtypes CR/CRIR
Large flanges in accordance with API 605, measures in inch
Nom
inal
wid
th
Subject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de
Subject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
KLINGERmaxiflextypes CR/CRIR
Large flanges in accordance with MSS SP 44, measures in inch
øI øI øA øAøI øI øA øAøI øI øA øAøI øI øA øA
Innerring
Sealing element
Cen-teringring
Innerring
Sealing element
Cen-teringring
Innerring
Sealing element
Cen-teringring
Sealing element
Cen-teringring
Innerring
Pressure stage [lbs]150
Pressure stage [lbs]300
Pressure stage [lbs]600
Pressure stage [lbs]900
d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4
Nom
inal
wid
th
d2d3d4
d4
d1d2d3
CR CRIR
d2d3d4
d4
d1d2d3
CR CRIR
4.75
7 M
axifl
ex 9
5Pa
nton
e Blau
541
Pa
nton
e Rot
206
øI øI øA øAøI øI øA øAøI øI øA øAøI øI øA øA
Innerring
Sealing element
Cen-teringring
Innerring
Sealing element
Cen-teringring
Innerring
Sealing element
Cen-teringring
Sealing element
Cen-teringring
Innerring
Pressure stage [lbs]150
Pressure stage [lbs]300
Pressure stage [lbs]600
Pressure stage [lbs]900
d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4
KLINGERmaxiflextypes CR/CRIR
Large flanges in accordance with API 605, measures in inch
Nom
inal
wid
th
KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de
Subject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
Subject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
KLINGER SWGtypes CR/CRIR
Large flanges in accordance with MSS SP 44, measures in inch
øI øI øA øAøI øI øA øAøI øI øA øAøI øI øA øA
Innerring
Sealing element
Cen-teringring
Innerring
Sealing element
Cen-teringring
Innerring
Sealing element
Cen-teringring
Sealing element
Cen-teringring
Innerring
Pressure stage [lbs]150
Pressure stage [lbs]300
Pressure stage [lbs]600
Pressure stage [lbs]900
d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4No
min
al w
idth
Pressure stage [lbs]150
P. s. [lbs] 300 bis 1500 300 400 600 900
Pressure stage [lbs]25001500
o/I o/I o/A o/A o/I o/A o/A o/I o/A o/A
Innerring
Sealingelement
Cente-ringring
Sealingelement
Centering ring Sealingelement
Cente-ringring
d1
[inch]
d2 d3 d4 d2 d3 d4 d2 d3 d4
4.75
7 M
axifl
ex 9
5Pa
nton
e Blau
541
Pa
nton
e Rot
206
Nom
inal
wid
th
d2d3d4
d4
d1d2d3
CR CRIR
d2d3d4
d4
d1d2d3
CR CRIR
Pressure stage [lbs]
KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de
Subject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
Subject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
Flanges in accordance with BS 3381, ANSI B 16.5,measures in inch
KLINGER SWGtypes CR/CRIR
Pressure stage [lbs]150
P. s. [lbs] 300 bis 1500 300 400 600 900
Pressure stage [lbs]25001500
o/I o/I o/A o/A o/I o/A o/A o/I o/A o/A
Innerring
Sealingelement
Cente-ringring
Sealingelement
Centering ring Sealingelement
Cente-ringring
d1
[inch]
d2 d3 d4 d2 d3 d4 d2 d3 d4
Nom
inal
wid
th
Pressure stage [lbs]
Flanges in accordance with BS 3381, ANSI B 16.5,measures in mm
KLINGERmaxiflextypes CR/CRIR
Pressure stage [lbs]150
P. s. [lbs] 300 bis 1500 300 400 600 900
Pressure stage [lbs]25001500
o/I o/I o/A o/A o/I o/A o/A o/I o/A o/A
Innerring
Sealingelement
Cente-ringring
Sealingelement
Centering ring Sealingelement
Cente-ringring
d1
[inch]
d2 d3 d4 d2 d3 d4 d2 d3 d4
4.75
7 M
axifl
ex 9
5Pa
nton
e Blau
541
Pa
nton
e Rot
206
Nom
inal
wid
th
d2d3d4
d4
d1d2d3
CR CRIR
d2d3d4
d4
d1d2d3
CR CRIRSubject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de
Subject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
Flanges in accordance with BS 3381, ANSI B 16.5,measures in inch
KLINGERmaxiflextypes CR/CRIR
Pressure stage [lbs]150
P. s. [lbs] 300 bis 1500 300 400 600 900
Pressure stage [lbs]25001500
o/I o/I o/A o/A o/I o/A o/A o/I o/A o/A
Innerring
Sealingelement
Cente-ringring
Sealingelement
Centering ring Sealingelement
Cente-ringring
d1
[inch]
d2 d3 d4 d2 d3 d4 d2 d3 d4No
min
al w
idth
Pressure stage [lbs]
Flanges in accordance with BS 3381, ANSI B 16.5,measures in mm
KLINGER SWGtypes CR/CRIR
d2d3d4
d4
d1d2d3
CR CRIR
d2d3d4
d4
d1d2d3
CR CRIR
150 300 600
[mm] [inch] o/I o/A
Sealingelement
Pressure stage [lbs]d2 d3
o/A
Cente-ringring
d4No
min
al w
idth
4.75
7 M
axifl
ex 9
5Pa
nton
e Blau
541
Pa
nton
e Rot
206
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
900
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
1500
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
2500No
min
al w
idth
o/I o/A o/Ao/I
Inner-ring
Sealingelement
Centeringring
Nominal pressure 10 k
Nom
inal
wid
th
o/I o/A o/Ao/I
d2 d3 d4d1 d2 d3 d4d1
Inner-ring
Sealingelement
Centeringring
Nominal pressure 16 k to 20 k
Nom
inal
wid
th
Subject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de
Subject to technical alterations.Status: October 2000
Certified according to DIN EN ISO 9001.
In accordance with the french standard NF–M–87621,measures in mm
KLINGER SWGtypes CR/CRIR
Fitting to JIS flanges. Nominal pressure 10 k and 16 to 20 k, measures in mm
KLINGERmaxiflextypes CR/CRIR
d2d3d4
d4
d1d2d3
CR CRIR
d2d3d4
d4
d1d2d3
CR CRIR
150 300 600
[mm] [inch] o/I o/A
Sealingelement
Pressure stage [lbs]d2 d3
o/A
Cente-ringring
d4
Nom
inal
wid
th
4.75
7 M
axifl
ex 9
5Pa
nton
e Blau
541
Pa
nton
e Rot
206
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
900
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
1500
o/I o/A
Sealingelement
d2 d3
o/A
Cente-ringring
d4
2500
Nom
inal
wid
th
o/I o/A o/Ao/I
Inner-ring
Sealingelement
Centeringring
Nominal pressure 10 k
Nom
inal
wid
th
o/I o/A o/Ao/I
d2 d3 d4d1 d2 d3 d4d1
Inner-ring
Sealingelement
Centeringring
Nominal pressure 16 k to 20 k
Nom
inal
wid
th
KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de
Subject to technical alterations.Status: 1995
Certified according to DIN EN ISO 9001.
Subject to technical alterations.Status: October 2000
Certified according to DIN EN ISO 9001.
In accordance with the french standard NF–M–87621,measures in mm
KLINGERmaxiflextypes CR/CRIR
Fitting to JIS flanges. Nominal pressure 10 k and 16 to 20 k, measures in mm
KLINGER SWGtypes CR/CRIR