Embed Size (px)
Citation preview
www.intmpe.com
MPVTP VERTICAL TURBINE PUMPS
Brochure Released on: Oct 2021. Last Edited: Nov 2021 Doc ID: 8006 Rev 1.4
2
www.intmpe.com
MPVTP. Vertical single stage or multistage pump with mixed or axial flow impeller design,
broad hydraulic coverage provides best selection to meet specific operating
conditions. Fabricated or cast iron, surface or underground discharge head, shaft
and bearing combinations promote long life with options of open or enclose line
shaft construction. It can be driven by VHS NEMA Standard motor, VSS motor or
diesel engine through right angle gear box.
General Technical Specification: • Capacities up to 5000 m3/h (22,000 Usgpm).
• Heads up to 350 meters (1148 Ft).
• Motor Power from 5.5 Kw (7 HP) to 1600 Kw (2144 HP).
• Rated Voltage: 380V, 480V, 2.3Kv, 4.16Kv, 10Kv, [50/60Hz].
• Temperatures up to 500° F (260° C)
• Bowl sizes from 150mm (6”) to 1375mm (55”)
• Well Diameter from 100mm (4”) to 950mm (38”).
• Discharge Diameter from 150mm (6”) to 650mm (26”).
Design Advantages: • Fabricated / Cast discharge head
• Flanged and/or Threaded columns.
• Flanged / Threaded bowl construction.
• 416SS shafting.
• Alloy construction with external flush of critical wear areas available for corrosive/abrasive services.
• Built-in alignment and simple piping for less costly installation and ease of maintenance/reduced downtime.
Services: • Cooling Water, Towers.
• Seawater and River Water Intake
• Industrial Process
• Utility Circulating Water
• Condenser Circulating Water Pumps
• Slurry Ash Sluice
• Municipal
• Agricultural Irrigation
• Mining.
Model Designation Description:
• 300 MPVTP 185-12X4
• # Stages
• Head per Stage
• Rated Capacity in m3/h
• MP Vertical Turbine Series
• Minimum Suitable Well ø mm
3
www.intmpe.com
New Generation of Pumps
The three different pump models in the Vertical Turbine Line
have Hydraulics designs that have efficiencies rates of 4 – 8
% higher than previous designs.
IntMPE Vertical Turbine covers a range of flow conditions up
to 5000 m3/h @ 350 M TDH. This covers most industry
needs with optimum efficiency.
IntMPE flexibility of design allows the use of a wide range of
materials and design features to meet the custom
requirements of the user. No matter what the
requirements, whether low initial cost, ease of
maintenance, optimum efficiency or tough service
conditions, IntMPE can make the pump to best satisfy the
requirements.
This bulletin is designed to assist the used in selecting the
pump for the conditions required, however, any question
will be answered promptly by IntMPE Technical Support
Team.
IntMPE Deep Well MPVTP Pumps can be equipped with
Whirl Sand Devices and the maze-like structure which
makes sand not enter the bearings. Shaft alignment is done
by Infrared method to ensure best operation and service
life.
Model MPVTP-OS/CS Model MPVTP-T
Model MPVTP-S
4
www.intmpe.com
Columns
Column Sections are provided with flanged ends incorporating fits for ease of alignment during assembly. This
facilitates disassembly where corrosion is a problem. Our Standard bearing retainers are welded into the
Column Section.
Open Line-Shaft Bearing
Flanged column / product lubricated line-shaft is
recommended for ease maintenance or whenever a
special bearing material is required. Keyed line-shaft
coupling available in all sizes for ease of maintenance.
Various bearing materials are available. Renewable
shaft sleeves or hard facing of shaft available for longer
life.
Open Line-Shaft Bearing
The Line-Shaft is protected by water flushing the
enclosing tube bearing or corrosive and/or
abrasive services. Oil Lubricated line-shaft available
on long settings. Alignment is attained by register
fit between the flange faces.
Threaded Line-Shaft Coupling
Threaded line-shaft coupling is commonly used for
lower horsepower pumps. It is less expensive.
Keyed Line-Shaft
Keyed Line-shaft coupling is recommended for motors
larger than 500 HO. It provides easier maintenance.
5
www.intmpe.com
Rigid Flanged Coupling (Type AR) To couple pump to vertical hollow shaft driver. Impeller adjustment is performed on adjusting nut located on top of motor.
Adjustable Coupling (Type A) For Vertical Solid Shaft driver, Impeller adjustment made by using adjustable plate in the coupling.
Adjustable Spacer Coupling (Type AS) Same function as type A coupling with addition of spacer. Spacer may be removed for Mechanical Seal Maintenance without Disturbing
Driver.
Couplings
Discharge Heads
The discharge head functions to change the direction of flow from vertical to horizontal and to couple the pump to the system piping in addition to supporting and aligning the driver. Discharge head accommodates all modes of drivers including hollow shaft and solid shaft motors, right angle gears, vertical steam turbines, etc. Optional sub-base can be supplied. intMPE offers three basic types for maximum flexibility.
Fabricated Discharge Head For pressures exceeding cast head limitations or services that require alloy construction such as high or low temperature or corrosive services. Segmented elbow available for efficiency improvement. Base flange can be machined to match ANSI tank flange.
Discharge Head MPT MPT can also be supplied as MPL with the Pump Suction in the can. This Head type will provide suction in one side and discharge on other side.
Below Ground Discharge Head Use whenever the pump is required to adapt to an Underground discharge system to keep the Discharge Head on top for easier access.
6
www.intmpe.com
Pump Performance Data
Model Stage Capacity (m3/h) Head (m) Motor Power String
Quantity Rotating
Speed Effi. Dia.
# Nominal Scope Rated Scope kW mm RPM % mm
100MPVTP10-4×
8
10 6.5-12
32 25-35 5.5
8 2940 62 92
10 40 32-44 5.5
12 48 38-53 5.5
14 52 44-62 5.5
16 64 51-70 5.5
18 72 57-79 5.5
20 80 64-88 5.5
22 88 70-97 5.5
24 96 76-106 5.5
26 104 83-115 5.5
150MPVTP10-9×
8
10 8-16
72 54-75 5.5
12 2940 62 138
9 81 61-84 5.5
10 90 67-93 5.5
11 99 61-102 7.5
12 108 81-112 7.5
13 117 87-121 7.5
14 126 94-130 7.5
15 135 101-140 11
16 144 108-149 11
17 153 114-158 11
18 162 121-167 11
19 171 128-176 11
150MPVTP20-11×
4
20 15-24
44 39-48 5.5
12 2940 67 150
5 55 49-60 5.5
6 66 59-72 7.5
7 77 69-84 7.5
8 88 78-96 11
10 110 98-120 11
12 121 118-144 15
14 154 134-168 15
150MPVTP30-12.5×
5
30 21-36
62.5 51-69 11
8 2940 70 150
6 75 61-83 11
7 87.5 71-96 15
8 100 82-110 15
9 112.5 92-124 15
10 125 102-138 18.5
11 137.5 112-152 18.5
12 150 123-165 22
13 162.5 133-180 22
7
www.intmpe.com
Pump Performance Data
150MPVTP40-13.5×
4
40 30-46
54 50-62 11
8 2940 72 150
5 67.5 62-77 15
6 81 75-93 15
7 94.5 87-108 18.5
8 108 100-124 18.5
9 121.5 112-139 22
10 135 125-155 30
11 148.5 137-170 30
12 162 150-186 30
150MPVTP50-13×
4
50 30-55
52 46-66 11
8 2940 74 150
5 65 57-82 15
6 78 69-99 18.5
7 91 80-115 22
8 104 92-132 22
9 117 103-148 30
225MPVTP60-20×
2
60 40-76
40 30-44 11
9 2940 75 181
3 60 45-66 18.5
4 80 60-88 22
5 100 75-110 30
6 120 90-132 37
7 140 105-154 37
225MPVTP80-22.5×
2
80 60-100
45 38-49 15
9 2940 75 181 3 67.5 57-73.5 22
4 90 76-98 30
5 112.5 95-122 37
225MPVTP90-20×
2
90 67-119
40 28-45 15
10 2940 75 190 3 60 43-68 22
4 80 57-91 30
5 100 72-114 37
225MPVTP125-18×
1
125 89-142
18 15-22 11
10 2940 76 190 2 36 30-43 18.5
3 54 45-65 30
4 72 60-86 37
250MPVTP130-8.5×
5
130 89-150
42.5 35-49 22
10 1460 78 242
6 51 42-59 30
7 59.5 49-69 37
8 68 56-79 37
9 76.5 63-89 45
10 85 70-99 45
11 93.5 77-109 55
12 102 84-119 55
8
www.intmpe.com
Pump Performance Data
300MPVTP160-11.5×
3
160 125-200
34.5 28.5-39 22
14 1460 80 295
4 46 38-52 30
5 57.5 47.5-65 37
6 69 57-78 45
7 80.5 66.5-91 55
8 92 76-104 75
9 103.5 85.5-117 75
10 115 95-130 75
11 126.5 104.5-143 90
12 138 114-156 90
300MPVTP185-12×
2
185 130-235
24 18.9-27 18.5
14 1460 80 295
3 36 28.4-40 30
4 48 37.8-54 37
5 60 47.2-67 45
6 72 56.7-81 55
7 84 66-94 75
8 96 75.6-108 75
9 108 85-121 90
10 120 94.5-135 90
300MPVTP220-13.5×
2
220 154-264
27 22-29 22
12 1460 80 295
3 40.5 34-44 37
4 54 45-59 45
5 67.5 57-74 55
6 81 68-89 75
7 94.5 79-104 90
8 108 91-119 90
350MPVTP300-15×
2
300 230-370
30 23-35 37
12 1460 80 346
3 45 34.5-52.5 55
4 60 46-70 75
5 75 57.5-87.5 90
6 90 69-105 110
7 105 80.5-122.5
132
350MPVTP370-16×
1
370 270-460
16 11.5-19 30
12 1460 80 346
2 32 23-38 55
3 48 34.5-57 75
4 64 46-76 90
5 80 57.5-95 110
6 96 69-114 132
9
www.intmpe.com
Pump Performance Data
350MPVTP400-18×
1
400 280-480
18 14-20.8 37
12 1460 80 346
2 36 29-41 55
3 54 43-62 90
4 72 58-83 110
5 90 73-104 132
400MPVTP450-30×
1
450 290-540
30 25-35 55
22 1475 80 430
2 60 50-70 110
3 90 75-105 150
4 120 100-140 200
5 150 125-175 250
400MPVTP550-27×
1
550 400-850
27 17.5-29 55
20 1475 81 430
2 54 35-58 110
3 81 52.5-87 180
4 108 70-116 225
5 135 87.5-145 280
450MPVTP650-32×
1
650 520-850
32 22-35 90
20 1475 80 520
2 64 44-70 180
3 96 66-105 250
4 128 88-140 350
5 160 110-175 400
450MPVTP900-30×
1
900 600-1100
30 24-34 110
20 1475 82 520
2 60 48-68 225
3 90 72-102 315
4 120 96-136 400
5 150 120-170 520
500MPVTP1000-29×
1
1000 790-1300
29 21-33 110
20 1475 83 600 2 58 42-66 225
3 87 63-99 350
4 116 84-132 450
500MPVTP1250-30×
1
1250 800-1750
30 18.5-36 150
17 1475 84 600 2 60 37-72 280
3 90 55.5-108 400
4 120 74-144 560
500MPVTP2000-31×
1 2000
1500-2400
31 25-36 250 22 1475 80 670
2 62 50-72 500
10
www.intmpe.com
Pump Dimensional Data
Model/Type Stages A B D1 D2 D3 D4 D5 D6 D7 H1 H2 H3 H4 H5 H6 L M1 M2 n a
10 1175
13 1460
18 1935
23 2410
26 2885
12 335 251 190 102 186 228 1665 343 573 127 228 M12 6 30
16 2105
20 2545
5 822
7 1082
9 1342
12 1732
13 1862
6 952
9 1212
10 1472
12 1732
4 692
6 952
8 1212
9 1342
10 1472 454 955
4 662
5 792
6 922
7 1052
8 1182
9 1312 955
M16 8 22.5394
807
850172 305 M16X300280 19 155 235 280 400
8 22.5394
807
850
150MPVTP50-13× 508 382 150 114
172 305 M16X300M1619 155 235 280 400150MPVTP40-13.5× 508 382 150 114 280
172 305 M16X300M16 8 22.5235 280 400 394
807
850
382 150 114 280 19 155150MPVTP30-12.5× 508
M16X300
M12
M16
6 30
8 22.5
573 127 228
807 172 305
228
280
40019
343
394
89
190
280
102
155
186
235
150MPVTP20-11×
508 382
335 251
150
M16 8 22.5280 155 235 280 394400
807 172 305M16X300
30
150MPVTP10-9×508 382
150 89 19
573 127 228 M16X300M12 619 102 186 228 400 343100MPVTP10-4x 335 251 92 76 200
Note: Dimensional Drawings are provided upon request of selected Model based on performance data and
physical Application Boundaries. The above table is for reference of some of the models listed only.
11
www.intmpe.com
MPVTP-OS (Open Shaft – Water Lube)
Typical Applications
• Mining
• Municipal
• Power Generation
• General Industry
• Chemical
12
www.intmpe.com
MPVTP-CS (Enclosed Shaft – Oil Lube)
Typical Applications
• Mining
• Municipal
• Power Generation
• General Industry
• Chemical
13
www.intmpe.com
MPVTP-TOS (Open Shaft – Can Pump)
Typical Applications
• Power Generation
• General Industry
• Chemical
• Hydrocarbon Processing
14
www.intmpe.com
CORPORATE OFFICE 425 3428 - 99 Street
Edmonton, Alberta T6E-5X5
TF: 1.877. INTMPE Ext#1 / 1.877.246.8673 Email: [email protected]
www.intmpe.com
