MSDS UofW Tacoma Y-Center

L - 1

Mortenson Construction

Project:

University of Washington Y-Center

Section 97200 Acrovyn Wall Panels

Section 097723 Prefinished Wall Panels (FRP)

L - 2

TABLE OF CONTENTS

Page

FRP Sheet Tech Data 1

FRP Moldings Tech Data 2-3

FRP Fast Grab Adhesive Tech Data 4-5

MSDS – FRP Sheet 6-10

MSDS - FRP Fast Grab Adhesive 11-20

MSDS – FRP Moldings 21-24

Acrovyn Sheet & Moldings Tech Data 25

MSDS – Acrovyn Sheet 4000 26-29

MSDS – Acrovyn HD Water Based Mastic 30

DOW 790 Joint Sealant Tech Data 31

MSDS Dow 790 32-39

7505Rev. 07 | 10.14Innovative Finishes - DESIGNS & DESIGNS4U | IPSA/IPSC/IPCN

ProductThe DESIGNS fi berglass reinforced plastic (FRP) panel with a unique, decorative image is a durable, fl exible building material and will not mold, mildew, rot or corrode. It exhibits excellent resistance to mild chemicals and moisture. The panel is available in a Class A or Class C fi re rating per ASTM E-84 or a panel tested per CAN/ULC-S102-M for use in Canada.

PurposeDESIGNS wall panels are designed for interior use only where a sanitary, easy-to-clean panel is desired. The decorative image enhances any area where the features and benefi ts of an FRP panel are required but a more cosmetically appealing fi nish is desired.

TECHNICAL DATA

NOTE: Due to the specialty custom nature of the DESIGNS production process, color variance from lot to lot production will occur. Panels will not be the exact same color from run to run. ORDER ENOUGH PANELS TO COMPLETE A ROOM INSTALLATION.

Table One: Physical PropertiesTypical Values

Property Class A (IPSA)

Class C (IPSC)

CAN/ULC-S-102-M (IPCN) Test Method

Flexural Strength 18 x 103 psi (124 Mpa)

12 x 103 psi(110 Mpa)

13 x 103 psi (90 Mpa) ASTM - D790

Flexural Modulus 0.60 x 106 psi(4137 Mpa)

0.50 x 106 psi(3447 Mpa)

0.50 x 106 psi(3447 Mpa) ASTM - D790

Tensile Strength 10 x 103 psi (69 Mpa)

7 x 103 psi (48 Mpa)

6 x 103 psi(41 Mpa) ASTM - D638

Tensile Modulus 0.8 x 106 psi(5516 Mpa)

0.9 x 106 psi(3450 Mpa)

0.70 x 106 psi(4826 Mpa) ASTM - D638

Barcol Hardness 45 35 40 ASTM - D2583

Impact Strength (IZOD) 8 ft-lb/in2 notched (0.43 J/mm)

5 ft-lb/in2 notched (0.27 J/mm)

6.0 ft-lb/in2 notched(0.32 J/mm) ASTM - D256

Coeffi cient of Linear Thermal Expansion

2 x 10-5 in/in/°F(36μm/m•°C)

2 x 10-5 in/in/°F(36μm/m•°C)

NAASTM - D696

Water Absorption 0.16%/24 hrs @ 77°F(25°C)

0.16%/24 hrs @ 77°F(25°C)

NAASTM - D570

Table Two: Design Typical Values

Fire Rating Product Code

Nominal Thickness Available Patterns/Colors Standard Sizes

Class A IPSA

0.075” (1.9mm)

Wood Patterns

4’ x 8’ | 4’ x 10’ (1.2m x 2.4m) (1.2m x 3.0m)

Sierra Ash | 010SA Baton Rouge Bamboo | 001BRB

Maryland Maple | 009MM Carolina Cherry | 002CC

Washington Wood | 008WW Tennessee Timber | 003TT

Stone & Natural Patterns

Class C IPSC

Scattered Stone | 004SS Sculptured Stone | 007SS

Maui Marble | 006MM True Terrazzo | 005TT

Caramel Crosshatch | 013CH

Canvas PatternsColonial Canvas | 012C Corn Silk Canvas | 008C

Camel Canvas | 010C Chrome Canvas | 011C

CAN/ULC-S102-M IPCN

Coastal Canvas | 007C Cactus Canvas | 009C

Innovative PatternsBrushed Metal | 025BM Piri Blue Stripe | 023PBS

Whipped Weave | 014W

DESIGNS4U Customized Patterns

Dan

Circle

Dan

Text Box

1

6220Rev. 24 | 5.13One-Piece Moldings, Two-Piece Moldings & Rivets

TECHNICAL DATA

PURPOSEFor use with panel thicknesses 0.075" and 0.09". For 0.12" panels use the 2 piece moldings.

PURPOSESee Table A for rivet size and corresponding panel thickness.

PRODUCTFor professional looking panel installations, and maximum moisture sealing effectiveness, use Crane Composites one-piece, non-staining, polypropylene moldings.

PRODUCTNon-staining nylon drive rivets in matching panel colors are designed for quick and easy installation using only a hammer and drill. When used with silicone sealants, drive rivets maintain an effective moisture seal as well as providing excellent mechanical fastening for panels.

Standard One-Piece Polypropylene Moldings

Standard Nylon Drive Rivets

Outside Corner | OC

Inside Corner | IC

Cap | CP

Division Bar | DB

Outside Angle | OAInside Angle | IA

.80

.100

.0401.420

.500

.095

.045

.870

.120

.550

.550

.085 .085

1.475

1.475

1.450

1.450

.100

.100

.035

.035

.865

.545

.700

Panel Thickness

Rivet Length

Available Colors

.09" to .125" (2.29 mm to 3.18 mm)

.75" (19.05 mm)

White, Cream, Beige, Silver, and Gray

.09" to .25" (2.29 mm to 6.35 mm)

1" (25.40 mm) White

.25" to .5" (6.35 mm to 12.70 mm)

1.5" (38.10mm) White

Table A

.11"

Length(see Table A)

When installing outside and inside angles to FRP panels, use Titebond® GREENchoice Advanced Polymer Panel Adhesive. Other adhesives that may be used include Loctite® Power Grab All-Purpose Construction Adhesive. Acrylic, epoxy or urethane based adhesives should be used to provide an adequate bond. Silicone sealant is not meant to be used as an adhesive and will not properly bond the angle to the FRP panel.

NOTE: Images are not drawn to scale and are depicted in inches.

Dan

Circle

Dan

Text Box

2

www.frp.com | 1.800.435.0080 | 1.815.467.8666 (fax) | [email protected] Composites is the manufacturer of Glasbord, Sequentia, Sanigrid II and a variety of other fiberglass reinforced plastic (FRP) composite wall panels. Inspired by the Kemlite tradition, Crane Composites has over 55 years of experience in Commercial Building Products and is a recognized industry leader in FRP applications. We believe all information given is accurate. It is offered in good faith, but without guarantee. Since conditions of use are beyond our control, all risks are assumed by the user. Nothing herein shall be construed as a recommendation for uses which infringe on valid patents or as extending a license under valid patents.

Form 6220 | Rev. 24 | 5.13 | (6587)

PURPOSEImproved installation time. Panel and molding can be installed in separate operations. Screws can be used to secure base and panel. Holes must be oversized.

PRODUCTFor professional looking Laminated FRP panel installations, and maximum moisture sealing effectiveness, use one-piece, non-staining vinyl moldings.

PRODUCTFor professional looking and convenient installations, use two-piece snap-on trim, non-staining, vinyl moldings. Available in white only. Use for all thicknesses.

Standard One-Piece Vinyl Moldings for Laminated FRP Panels

Two-Piece Surface Mount Vinyl Moldings

DIVISION BARPart B

Part A

1.575"

0.065"

0.125"

1.30"

INSIDE CORNERPart A 0.73"

0.73"

1.46"

Part B

OUTSIDE CORNERPart B

Part A

1.00"

0.95"

CAP (CP)

0.420"

1.235"

0.720"

DIVISION BAR (DB)0.750"

0.440"

1.720"

INSIDE CORNER (IC)

0.809"

0.445"0.920"

1.230"

OUTSIDE CORNER (OC)0.690"

1.320"

0.440"

0.970"

PURPOSEFor use with Laminated FRP installationsup to 0.437" thick.

T-BAR (TB)*1.500"

.050"

.320"

.150".455"

.110"

* T-Bar is extruded Polypropylene

Inside and Outside Angles are also available for Glasbord Laminated (Kemply) installations. Please refer to Standard One-Piece Polypropylene Moldings on the other side of this page for dimensions

Loctite® is a registered trademark of Henkel Corporation. Titebond® is a registered trademark of Franklin Adhesives & Polymers.

Dan

Circle

Dan

Text Box

3

7651Rev. 3 | 6.14 Fast Grab Adhesive | R53828

TECHNICAL DATA

DescriptionFast Grab Adhesive offers professional-strength and is specifically formulated for the installation of FRP panels over most porous surfaces. It is ideal for bonding FRP panels to drywall, non-treated plywood, concrete, and most other common porous building materials. It offers quick grab and strength development that requires minimal bracing. Fast Grab FRP Adhesive is a safer alternative to solvent-based technologies.

Shelf Life / StorageWhen stored in its original, tightly sealed container, Crane Composites FRP Adhesive has a shelf life of over one year (1 yr.) from the date of manufacture. See next page for assistance to determine date.

Application TemperatureOver 50°F and below 90°F for adhesive and substrates.

Service Temperature0°F. to 110°F

Coverage50 sq. ft. per gallon

Work Time20 minutes at 70°F

Application LimitationsThis product is for interior installations only. For best results, store Crane Composites Fast Grab Panel Adhesive above 50°F. Before installation it is important to wipe down all FRP with acetone if an oily residue is present as this can deter adhesion.

Solvent-Free FRP AdhesiveCleanroom & Hygienic Wall System Recommended

Physical Properties*Property Value

Type Proprietary Emulsion Polymer

State Low Viscosity Mastic

Color Light Beige

Solids 67%

Viscosity 100,000 cps

Calculated VOC 2.6 g/L

Flashpoint >200°F

Application 5/16′′ x 3/16′′ x 1/4′′ V-Notched Trowel

Shelf Life 24 Months**

* Data is typical and not to be used for specification purposes** Shelf Life - when stored in its original, tightly sealed container, see next page for assistance to determine date

Features and BenefitsRequires Minimal BracingVOC-Compliant, NonflammableQuick Grab FormulaNo Offensive Odor

Dan

Circle

Dan

Text Box

4

Form 7651 | Rev. 3 | 6.14 | (7152)

www.FRP.com | 1.800.435.0080 | 1.815.467.8666 (fax) | [email protected] Composites is the manufacturer of Glasbord, Sanigrid II and a variety of other fiberglass reinforced plastic (FRP) composite wall panels. Inspired by the Kemlite tradition, Crane Composites has over 55 years of experience in Commercial Building Products and is a recognized industry leader in FRP applications.

Values stated in this technical data sheet represent typical values as not all tests are run on each lot of material produced. For formalized product specifications for specific product end uses, contact the Customer Service at 1.800.435.0080.

Information provided herein is based upon tests believed to be reliable. In as much as Crane Composites has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, Crane Composites does not guarantee the performance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fitness for a particular purpose concerning the effects or results of such use.

Working SurfacesSurfaces must be free of any material that may deter adhesion, including severe and thick amounts of drywall joint compound. Patch large holes and depressions and remove any bumps, high spots, dust, oil, and grease. Cut and pre-fit all panels. Lay panels flat and let them acclimate to room temperature 24 hours before installing.

Note: Bracing may be required if walls or panels are not straight. Panels used in conjunction with channel moldings should NOT fit tightly into the moldings. Leave a small gap under the molding for expansion and follow panel manufacturer’s recommendations. Any holes drilled through the panels for fasteners, pipes or conduits should be oversized to allow for natural movement of the panel.

Clean UpTools and excess adhesive may be cleaned with water while wet. If adhesive has dried, use mineral spirits. Follow solvent vendor’s precautions when using solvents.

NOTE: Test solvent in an out-of-the-way area to make sure it will not mar or attack the surface.

Caution StatementWARNING: EYE AND SKIN IRRITANT. Do not swallow. Do not allow eye contact or prolonged skin contact. First Aid: If swallowed, do not induce vomiting; contact physician. If eye contact occurs, flush eyes with water for 15 minutes. Wash skin contact areas with soap and water. If irritation from eye and skin contact persists, contact physician. Product releases methanol during cure. For additional information, refer to Material Safety Data Sheet. KEEP OUT OF THE REACH OF CHILDREN.

Manufacturer DateThe expected shelf life for unopened Advanced Polymer (R53829) and Fast Grab (R53828) Adhesive is one year from the date of manufacture. The date of manufacture can be determined by the lot number stamped on the pail. Our lot number will start with an A, followed by several numbers. The first number will be the last digit in the year of manufacture. Products made in 2014 will have a 4. The next two numbers will indicate the month and the next two numbers will indicate the day. For example the lot number for product manufactured on April 15, 2014 would be A40415. Where the product is stored can affect the actual shelf life.

Dan

Circle

Dan

Text Box

5

MATERIAL SAFETY DATA SHEET

1. Product and Company Identi�cationMaterial name Crane Composite frp Panel Products unless otherwise noted

Revision date 10-16-2014

Version # 06

Chemical description Fiberglass Reinforced Plastic (frp)

Product code ANXT, EARM, EAIS, LIC, ETR, LTR, STI, TI, CNSI, FSI, FX, FXE, PCI, PIF, PSIF, CGI, FSQF,FTSTF, FRFRJ, IPSA, IPSC, IPSCAN, SMXGC, STA, MXGC, SSTA, LBALN, STC, LBCLN, C25S,C25T, ***GP, ***DL, ***ST, ***SS, ***CTN, ***CTA, HGR, DSC, PWI, RBP, RVPRJ, RVSR, SDSC,RISC, AFL, TRW, ARMX, ARMR, TRF, RBP2, RGD, RGD2, RDMC, RTMC, RBMC, RBMCL, LHS, TIB, AFS, ARMT, RCHW, EGAT, EATR, REF, STI, LPC, MED , REI, SDUR, AXSG, FRCW, STCW, STCWW, RBMC2, RBMC2L, RDMC2, AXS, CAU

Product use High Impact Liner for Refrigerated Trailers, Truck Bodies, Containers and Railcars.Liners and Roofs for Refrigerated and Dry Trailers, Truck bodies, Containers and Railcars.Interior Wall and Ceiling panels where sanitary, durable, easy to clean �nishes are required.Exterior Corrugated Daylighting and Opaque Panels for residential, commerical and industrial use.Gel-Coated and Non Gel Coated Exterior panels for use as sidewalls and roof panels onrecreational vehicles.

Miscellaneous other panels of similar design (estimated count 100)

Synonym(s) Armortuf * Kemlite * Glasbord * Sequentia * Innovative Finishes * Sequentia Corrugated *Engineered Solutions * Filon

Manufacturer/Supplier Crane Composites Inc23525 W. Eames StreetChannahon, IL 60410-3220 US

815-467-8600Telephone number

2. Hazards Identi�cation

Physical state Solid.

Appearance Rigid sheet.

Emergency overview Low hazard under normal conditions. Fabricating, cutting, drilling, etc. of frp may produce dust,which may irritate the eyes, skin and respiratory system.

OSHA regulatory status This product is an article pursuant to 29 CFR 1910.1200 and, as such, is not subject to the OSHAHazard Communication Standard.

Potential health e�ectsEyes Mechanical processing may generate dust. Dust may irritate the eyes.

Skin Dust may irritate skin.

Inhalation Dust may irritate the respiratory system.

Ingestion Ingestion is not likely to be a primary route of occupational exposure.

Target organs Eyes. Skin. Respiratory system.

Signs and symptoms Irritation of nose and throat. Irritation of eyes and mucous membranes. Upper respiratory tractirritation.

3. Composition / Information on IngredientsThe manufacturer lists no ingredients as hazardous according to OSHA 29 CFR 1910.1200.

Composition comments Panels are solid sheets composed of a mixture of polyester resin, inorganic �llers, pigments,processing additives, and �berglass reinforcement. During the manufacturing process, thismixture is cured or hardened into a stable, solid material that is non-hazardous when handled orprocessed in accordance with good manufacturing and industrial hygiene practices.

4. First Aid MeasuresFirst aid procedures

Eye contact Flush eyes with water as a precaution. Get medical attention if irritation develops or persists.

Skin contact Remove contaminated clothing and wash skin with soap and water. Get medical attention ifirritation develops or persists.

Inhalation If dust from the material is inhaled, remove the a�ected person immediately to fresh air. Getmedical attention if symptoms persist.

CPH MSDS NA

1 / 5Crane Composite frp Panel Products unless otherwise noted904971 Version #: 06 Revision date: 10-16-2014

Gel-Coated Exterior panels for use as tank cladding on insulated tank containers.

Dan

Circle

Dan

Text Box

6

Ingestion First aid is normally not required. Ingestion of large amounts may cause gastrointestinalsymptoms.

Notes to physician Treat symptomatically.

5. Fire Fighting MeasuresFlammable properties This product is not �ammable. This product is a dust explosion class St-1 at normal moisture

level.

Extinguishing mediaSuitable extinguishingmedia

Use �re-extinguishing media appropriate for surrounding materials.

Fire �ghtingequipment/instructions

Selection of respiratory protection for �re�ghting: follow the general �re precautions indicated inthe workplace.

Hazardous combustionproducts

During �re, gases hazardous to health may be formed.

6. Accidental Release MeasuresPersonal precautions Avoid inhalation of dusts from machining operation. Use personal protection as recommended in

Section 8 of the MSDS.

Environmental precautions No speci�c precautions.

Methods for cleaning up No speci�c clean-up procedure noted.

Other information Collect and dispose of spillage as indicated in Section 13 of the MSDS.

7. Handling and StorageHandling Do not eat, drink or smoke when using the product. Avoid inhalation of dust. Observe good

industrial hygiene practices.

Storage Store away from incompatible materials. Keep away from heat, sparks and open �ame.

8. Exposure Controls / Personal ProtectionOccupational exposure limits

US. ACGIH Threshold Limit ValuesFormValueTypeComponents

.selcitrap elbaripseR3m/gm 3AWT)-( tsuD10 mg/m3 Inhalable particles.

US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)FormValueTypeComponents

.noitcarf elbaripseR3m/gm 5LEP)-( tsuD15 mg/m3 Total dust.

US. OSHA Table Z-3 (29 CFR 1910.1000)FormValueTypeComponents

.noitcarf elbaripseR3m/gm 5AWT)-( tsuD15 mg/m3 Total dust.50 mppcf Total dust.15 mppcf Respirable fraction.

Canada. Alberta OELs (Occupational Health & Safety Code, Schedule 1, Table 2)FormValueTypeComponents

.selcitrap elbaripseR3m/gm 3AWT)-( tsuD10 mg/m3 Total particulate.

Canada. British Columbia OELs. (Occupational Exposure Limits for Chemical Substances, Occupational Health andSafety Regulation 296/97, as amended)

FormValueTypeComponents.noitcarf elbaripseR3m/gm 3AWT)-( tsuD

10 mg/m3 Total dust.

Canada. Ontario OELs. (Control of Exposure to Biological or Chemical Agents)FormValueTypeComponents

.selcitrap elbaripseR3m/gm 3AWT)-( tsuD10 mg/m3 Inhalable

CPH MSDS NA


Dan

Circle

Dan

Text Box

7

Canada. Quebec OELS. (Ministry of Labor - Regulation Respecting the Quality of the Work Environment)FormValueTypeComponents

.tsud latoT3m/gm 01AWT)-( tsuD

Engineering controls Ventilate as needed to control airborne dust. Use explosion-proof ventilation equipment if airbornedust levels are high.

Personal protective equipmentEye / face protection Use tight �tting goggles if dust is generated by machining operation.

Skin protection Wear protective gloves, long pants and long sleeves when machining, cutting, drilling, etc.

Respiratory protection Under normal conditions, respirator is not normally required. In case of inadequate ventilation orrisk of inhalation of dust, use suitable respiratory equipment with particle �lter.

General hygieneconsiderations

Always observe good personal hygiene measures, such as washing after handling the materialand before eating, drinking, and/or smoking. Routinely wash work clothing and protectiveequipment to remove contaminants.

9. Physical & Chemical Properties

Appearance Rigid sheet.

Color Not available.

Odor Odorless.

Odor threshold Not available.


Form Solid.

pH Not available.

Melting point Not available.

Freezing point Not available.

Boiling point Not available.

Flash point Not available.

Evaporation rate Not available.

Flammability limits in air, upper,% by volume

Not available.

Flammability limits in air, lower,% by volume

Not available.

Vapor pressure Not available.

Vapor density Not available.

Speci�c gravity 1.2 - 1.8

Solubility (water) Insoluble.

Partition coe�cient(n-octanol/water)

Not available.

Auto-ignition temperature Not available.

Decomposition temperature Not available.

10. Chemical Stability & Reactivity InformationChemical stability Stable under normal temperature conditions.

Conditions to avoid None under normal conditions.

Incompatible materials Alkalies. Strong acids. Oxidizing agents.

Hazardous decompositionproducts

Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecularweight hydrocarbons.

Possibility of hazardousreactions

Hazardous polymerization does not occur.

11. Toxicological Information

Acute e�ects None known.

Local e�ects Dusts may irritate the respiratory tract, skin and eyes.

Sensitization Not a skin sensitizer.

Carcinogenicity Not classi�ed.CPH MSDS NA


Dan

Circle

Dan

Text Box

8

Epidemiology Pre-existing skin and respiratory conditions including dermatitis, asthma and chronic lung diseasemight be aggravated by exposure.

Mutagenicity Not classi�ed.

Reproductive e�ects Not classi�ed.

Symptoms and targetorgans

Irritation of nose and throat. Irritation of eyes and mucous membranes. Upper respiratory tractirritation.

12. Ecological Information

Ecotoxicity Not expected to be harmful to aquatic organisms.

Persistence anddegradability

No data available.

Bioaccumulation /Accumulation

No data available.

Partition coe�cient(n-octanol/water)

Not available.

Mobility in environmentalmedia

The product is insoluble in water.

13. Disposal ConsiderationsDisposal instructions Dispose of in accordance with all applicable regulations.

14. Transport Information

DOTNot regulated as dangerous goods.

IATANot regulated as dangerous goods.

IMDGNot regulated as dangerous goods.

TDGNot regulated as dangerous goods.

15. Regulatory InformationUS federal regulations This product is an article pursuant to 29 CFR 1910.1200 and, as such, is not subject to the OSHA

Hazard Communication Standard.

TSCA Section 12(b) Export Noti�cation(40 CFR 707, Subpt. D)Not regulated.

CERCLA (Superfund) reportable quantity (lbs) (40 CFR 302.4)

None

Superfund Amendments and Reauthorization Act of 1986 (SARA)Hazard categories Immediate Hazard - No

Delayed Hazard - NoFire Hazard - NoPressure Hazard - NoReactivity Hazard - No

Section 302 extremelyhazardous substance (40CRF 355, Appendix A)

No

Section 311/312 (40 CFR370)

No

Drug EnforcementAdministration (DEA) (21 CFR1308.11-15)

Not controlled

WHMIS status Non-controlled

Inventory status

Country(s) or region Inventor *)on/sey( yrotnevni nOeman yNo)SCIA( secnatsbuS lacimehC fo yrotnevnI nailartsuAailartsuA

CPH MSDS NA


Dan

Circle

Dan

Text Box

9

Country(s) or region Inventor *)on/sey( yrotnevni nOeman yNo)LSD( tsiL secnatsbuS citsemoDadanaC

No)LSDN( tsiL secnatsbuS citsemoD-noNadanaC

No)CSCEI( anihC ni secnatsbuS lacimehC gnitsixE fo yrotnevnIanihC

NolacimehC laicremmoC gnitsixE fo yrotnevnI naeporuEeporuESubstances (EINECS)

No)SCNILE( secnatsbuS lacimehC deifitoN fo tsiL naeporuEeporuE

No)SCNE( secnatsbuS lacimehC weN dna gnitsixE fo yrotnevnInapaJ

No)LCE( tsiL slacimehC gnitsixEaeroK

NoNew Zealand New Zealand Inventory

NoPhilippines Philippine Inventory of Chemicals and Chemical Substances(PICCS)

NoUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing cou ntry(s)

State regulations This product does not contain a chemical known to the State of California to cause cancer, birthdefects or other reproductive harm.

16. Other InformationHMIS® ratings Health: 0

Flammability: 0Physical hazard: 0

NFPA ratings Health: 0Flammability: 0Instability: 0

Disclaimer The information in the sheet was written based on the best knowledge and experience currentlyavailable.

Issue date 04-09-2014

CPH MSDS NA


Dan

Circle

Dan

Text Box

10

Crane Composites | Fast Grab Adhesive 1 | P a g e Form # 7656 | Rev. 01 | 07.13 (6739)


1. Product and Company Identification

Material name Fast Grab Adhesive

Revision date 7-29-2013

Version # 00

CAS# Mixture

Manufacturer for Crane Composites Inc 23525 W. Eames Street | Channahon, IL 60410-3220 US

Telephone number 800-435-0080

In case of emergency 800-424-9300

Product code R53828

Chemical family Adhesive. Solvent Free Adhesive.

2. Hazards Identification

EMERGENCY OVERVIEW Physical state Liquid. [Paste].

Color Brown. [Light].

Odor Characteristic. [Slight]

Signal word WARNING!

Hazard statements CAUSES EYE IRRITATION. MAY BE HARMFUL IF SWALLOWED. MAY CAUSE SKIN RESPIRATORY TRACT AND SKIN IRRITATION.

Precautionary measures Do not ingest. Avoid breathing vapor or mist. Use only with adequate ventilation. Avoid contact with eyes, skin and clothing. Keep container tightly closed. Wash thoroughly after handling.

OSHA/HCS status This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).

POTENTIAL ACUTE HEALTH EFFECTS

Inhalation Inhalation of oil mist or vapors at elevated temperatures may cause respiratory irritation. Slightly irritating to the respiratory system. Exposure to decomposition products may cause a health hazard. Serious effects may be delayed following exposure.

Ingestion Harmful if swallowed

Skin Slightly irritating to the skin.

Eyes Irritating to eyes.

POTENTIAL ACUTE HEALTH EFFECTS Chronic effects No known significant effects or critical hazards.

Carcinogenicity No known significant effects or critical hazards.

Mutagenicity No known significant effects or critical hazards.

Teratogenicity No known significant effects or critical hazards.

Development effects No known significant effects or critical hazards.

Fertility effects No known significant effects or critical hazards.

Target organs May cause damage to the following organs: upper respiratory tract, skin, eyes. Contains material which may cause damage to the following organs: eyes, lens or cornea.

Dan

Circle

Dan

Text Box

11


OVER-EXPOSURE SIGNS/SYMPTOMS Inhalation Adverse symptoms may include the following: respiratory tract irritation, coughing.

Ingestion No specific data.

Skin Adverse symptoms may include the following: irritation, redness

Eyes Adverse symptoms may include the following: pain or irritation, watering, redness

Medical conditions aggravated None known. by over-exposure

see toxicological information in section 11

3. Composition / Information on Ingredients United States

Name CAS number % oxydipropyl dibenzoate 27138-31-4

57-13-6 1 – 5 1 – 5

Canada

Name CAS number % oxydipropyl dibenzoate urea ethanediol

27138-31-4 57-13-6 107-21-1

1 – 5 1 – 5 0.5 – 1

Mexico

Name CAS number UN number % IDLH Classification H F R Special

urea oxydipropyl dibenzoate

27138-31-4 57-13-6

Not available. Not available.

1 – 5 1 – 5

- -

2 2

0 0

0 0

- -

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section.

4. First Aid Measure

Eye contact Check for and remove any contact lenses. Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical attention immediately.

Skin contact In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention immediately.

Inhalation Move exposed person to fresh air. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention immediately.

Ingestion Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical attention immediately.

Protection of first-aiders No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.

Notes to physician In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours.

Dan

Circle

Dan

Text Box

12


5. Fire-Fighting Measures

Flammability of the product In a fire or if heated, a pressure increase will occur and the container may burst.

EXTINGUISHING MEDIA Suitable Use an extinguishing agent suitable for the surrounding fire.

Not suitable None known.

Special exposure hazards Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training.

Special protective equipment Fire-fighters should wear appropriate protective equipment and self-contained breathing for fire-fighters apparatus (SCBA) with a full face-piece operated in positive pressure mode.

6. Accidental Release Measures

Personal precautions No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Do not breathe vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment (see Section 8).

Environmental precautions Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).

Small spill Stop leak if without risk. Move containers from spill area. Dispose of via a licensed waste disposal contractor. Absorb with an inert material.

Large spill Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see section 1 for emergency contact information and section 13 for waste disposal.

7. Handling and Storage

Handling Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist. Do not ingest. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container.

Storage Do not store below the following temperatures: 0°C (32°F). Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination.

Dan

Circle

Dan

Text Box

13


8. Exposure Controls / Personal Protection United States

Ingredient Exposure limits Urea AIHA WEEL (United States, 10/2011).

TWA: 10 mg/m³ 8 hour(s). Canada Occupational exposure limits TWA (8 hours) STEL (15 mins) Ceiling Ingredient List name ppm mg/m³ Other ppm mg/m³ Other ppm mg/m³ Other Notations methanol urea

US ACGIH 3/2012 AB 4/2009 BC 4/2012 ON 7/2010 QC 9/2011 US AIHA 10/2011

- - - - - - - -

- - - 10 - - - 10

- - - - - - - -

- - - - - - 50 -

- - - 20 - - 127 -

- - - - - - - -

- - - - 50 - - -

100 100 100 - - 100 - -

- - - - - - - -

[a] [3] [b] [a] [c] [d] [b] [e]

[3] Skin sensitization. Form: [a] Aerosol [b] aerosol [c] Particulate [d] Vapour [e] vapour and mist MEXICO OCCUPATIONAL No exposure limit value known EXPOSURE LIMITS Consult local authorities for acceptable exposure limits.

Recommended monitoring If this product contains ingredients with exposure limits, personal, workplace atmosphere procedures or biological monitoring may be required to determine the effectiveness of the ventilation or other control measures and/or the necessity to use respiratory protective equipment.

Engineering measures No special ventilation requirements. Good general ventilation should be sufficient to control worker exposure to airborne contaminants. If this product contains ingredients with exposure limits, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure below any recommended or statutory limits.

Hygiene measures Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.

PERSONAL PROTECTION

Respiratory Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator.

Hands Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary.

Eyes Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists or dusts.

Skin Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

Environmental exposure Emissions from ventilation or work process equipment should be checked to ensure they controls comply with the requirements of environmental protection legislation.

Dan

Circle

Dan

Text Box

14


9. Physical and Chemical Properties

Physical state Liquid. [Paste.]

Flash point Closed cup: >93.3ºC (>199.9°F) [Setaflash.]

Color Brown. [Light].

Odor Characteristic. [Slight]

pH 5

Boling/condensation point 100ºC (212°F)

Relative density 1.39

Volatility 33% (w/w)

Evaporation rate <1 (butyl acetate = 1)

VOC (less water, less 2.6 g/l exempt solvents)

Solubility Soluble in the following materials: cold water and hot water

10. Stability and Reactivity Chemical stability The product is stable.

Conditions to avoid No specific data.

Incompatible materials No specific data.

Hazardous decomposition Under normal conditions of stage and use, hazardous decomposition products should products not be produced. Methanol

Possibility of hazardous Under normal conditions of storage and use, hazardous reactions will not occur. reactions

Hazardous polymerization Under normal conditions of storage and use, hazardous polymerization will not occur.

Incompatibility Reactive or incompatible with the following materials: oxidizing materials and moisture.

11. Toxicological Information

UNITED STATES Acute toxicity

Product/ingredient name Result Species Does Exposure urea oxydipropyl dibenzoate

LD50 Oral LD50 Oral

Rat Rat

8471 mg/kg 3295 mg/kg

- -

Chronic toxicity No known significant effects or critical hazards. Irritation/Corrosion

Product/ingredient name Result Species Score Exposure Observation urea Skin – Mild irritant

Skin – Moderate irritant Human Human

- -

72 hours 22 milligrams Intermittent 24 hours 20 Percent

- -

Conclusion/Summary

Skin Prolonged or repeated contact can defat the skin and lead to irritation, cracking and/or dermatitis.

Eyes This product may irritate eyes upon contact

Respiratory Inhalation of oil mist or vapors at elevated temperatures may cause respiratory irritation

Sensitizer No known significant effects or critical hazards

Carcinogenicity No known significant effects or critical hazards

Mutagenicity No known significant effects or critical hazards

Teratogenicity No known significant effects or critical hazards

Reproductive toxicity No known significant effects or critical hazards

Dan

Circle

Dan

Text Box

15


CANADA

Acute toxicity Product/ingredient name Result Species Does Exposure ethanediol oxydipropyl dibenzoate urea

LD50 Oral LD50 Oral LD50 Oral

Rat Rat Rat

4700 mg/kg 3295 mg/kg 8471 mg/kg

- - -


Product/ingredient name Result Species Score Exposure Observation Ethanediol urea

Eyes – Mild irritant Eyes – Mild irritant Eyes – Moderate irritant Skin – Mild irritant Skin – Mild irritant Skin – Moderate irritant

Rabbit Rabbit Rabbit Rabbit Human Human

- - - - - -

24 hours 500 milligrams 1 hour 100 milligrams 6 hours 1440 milligrams 555 milligrams 72 hours 22 milligrams Intermittent 24 hours 20 Percent

- - - - - -

Conclusion/Summary









MEXICO

Acute toxicity Product/ingredient name Result Species Does Exposure urea oxydipropyl dibenzoate

LD50 Oral LD50 Oral

Rat Rat

8471 mg/kg 3295 mg/kg

- -


Product/ingredient name Result Species Score Exposure Observation - Skin – Mild irritant

Skin – Moderate irritant Human Human

- -

72 hours 22 milligrams Intermittent 24 hours 20 Percent

- -

Conclusion/Summary









Dan

Circle

Dan

Text Box

16


12. Toxicological Information Ecotoxicity No known significant effects or critical hazards UNITED STATES

Aquatic ecotoxicity Product/ingredient name Result Species Exposure Urea Acute EC50 391000 ug/L Fresh water

Acute LC50 1000 mg/L Marine water Acute LC50 5000 mg/L Fresh water

Daphnia – Daphnia magma - Neonate - <24 hours Crustaceans – Chaetogammarus Marinus – Young – 5mm Fish – Colisa fasciata - Fingerling

48 hours 48 hours 96 hours

Persistence/degradability No known significant effects or critical hazards.

CANADA

Aquatic ecotoxicity Product/ingredient name Result Species Exposure Ethanediol Urea

Acute LC50 100000 ug/L Marine water Acute LC50 10000000 ug/L Fresh water Acute LC50 8050000 ug/L Fresh water Acute EC50 3910000 ug/L Fresh water Acute LC50 1000 mg/L Marine water Acute LC50 5000 ug/L Fresh water

Crustaceans - Crangon crangon - Adult Daphnia – Daphnia magma Fish - {Pimephales promelas - <=7 days Daphnia – Daphnia magma - Neonate - <24 hours Crustaceans – Chaetogammarus Marinus – Young – 5mm Fish – Colisa fasciata – Fingerling

48 hours 48 hours 96 hours 48 hours 48 hours 96 hours

No known significant effects or critical hazards.


MEXICO Aquatic ecotoxicity

Product/ingredient name Result Species Exposure Urea Acute EC50 391000 ug/L Fresh water

Acute LC50 1000 mg/L Marine water Acute LC50 5000 mg/L Fresh water

Daphnia – Daphnia magma - Neonate - <24 hours Crustaceans – Chaetogammarus Marinus – Young – 5mm Fish – Colisa fasciata - Fingerling

48 hours 48 hours 96 hours

No known significant effects or critical hazards.


13. Disposal Considerations

Waste disposal The generation of waste should be avoided or minimized wherever possible. Significant quantities of waste product residues should not be disposed of via the foul sewer but processed in a suitable effluent treatment plant. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Disposal should be in accordance with applicable regional, national and local laws and regulations.

Refer to Section 7: HANDLING AND STORAGE and Section 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for additional handling information and protection of employees.

Dan

Circle

Dan

Text Box

17


14. Transport Information Regulatory information UN number Proper

shipping name Classes PG* Label Additional

Information DOT Classification Not regulated. - - - - TDG Classification Not regulated. - - - - Mexico Classification Not regulated. - - - - ADR/RID Class Not regulated. - - - - IMDG Class Not regulated. - - - - IATA-DGR Class Not regulated. - - - -

PG*: Packing group

15. Regulatory Information

UNITED STATES HCS Classification Irritating material

U.S. Federal regulations TSCA 4(a) final test rules: sodium hydroxymethanesulphinate; acetaldehyde TSCA 8(a) PAIR: acetaldehyde TSCA 8(a) IUR Exempt/Partial exemption: Not determined

United States inventory (TSCA 8b): All components are listed or exempted. SARA 302/304/311/312 extremely hazardous substances: No products were found. SARA 302/304 emergency planning and notification: No products were found. SARA 302/304/311/312 hazardous chemicals: No products were found. SARA 311/312 MSDS distribution - chemical inventory - hazard identification: No products were found.

Clean Air Act Section 112(b) Not listed Hazardous Air Pollutants (HAPs)

Clear Air Act Section 602 Not listed Class I Substance

Clean Air Act Section 602 Not listed Class II Substances

DEA List I Chemicals Not listed (Precursor chemicals)

DEA List II Chemicals Not listed (Essential Chemicals)

STATE REGULATIONS

Massachusetts None of the components are listed.

New York None of the components are listed.

New Jersey None of the components are listed.

Pennsylvania None of the components are listed.

CANADA

WHMIS (Canada) Class D-2B: Material causing other toxic effects (Toxic).

CANADIAN LISTS

Canadian NPRI None of the components are listed.

CEPA Toxic substances None of the components are listed.

Canada inventory Not determined.

Dan

Circle

Dan

Text Box

18


This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations and the MSDS contains all the information required by the Controlled Products Regulations. MEXICO Classification INTERNATIONAL REGULATIONS

International lists Australia inventory (AICS): Not determined. China inventory (IECSC): Not determined. Japan inventory: Not determined. Korea inventory: Not determined. New Zealand Inventory of Chemicals (NZIoC): Not determined. Philippines inventory (PICCS): Not determined.

Chemical weapons Not listed Convention List Schedule I Chemicals Chemical weapons Not listed Convention List Schedule II Chemicals Chemical weapons Not listed Convention List Schedule III Chemicals

16. Other Information Label requirements CAUSES EYE IRRITATION. HARMFUL IF SWALLOWED. MAY CAUSE

RESPIRATORY TRACT AND SKIN IRRITATION.

Hazardous Material Information System (USA)

Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks Although HMIS® ratings are not required on MSDSs under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered mark of the National Paint & Coatings Association (NPCA). HMIS® materials may be purchased exclusively from J. J. Keller (800) 327-6868.

The customer is responsible for determining the PPE code for this material.

Dan

Circle

Dan

Text Box

19


National Fire Production (USA)

Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright ©1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety. Copyright ©2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.

Date of printing 7/29/2013

Date of issue 7/29/2013

Date of previous issue No previous validation

Version 1

Notice to reader To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.

Dan

Circle

Dan

Text Box

20


1. Product and Company IdentificationMaterial name Molding Accessories for frp panelsRevision date 12-02-2011Version # 01Chemical description Flexible PVC compoundsProduct code M.Molding, V.MoldingProduct use Trim pieces that are used between panels to cover the expansion / contraction joings.Synonym(s) Polypropylene Moldings * Polyvinyl Chloride MoldingsManufacturer/Supplier Crane Composites Inc

23525 W. Eames StreetChannahon, IL 60410-3220 US

815-467-8600Telephone number

2. Hazards IdentificationPhysical state Solid.Appearance Finished products are 8,10, and 12 foot pieces in several shapes and colors.Emergency overview Low hazard under normal conditions.OSHA regulatory status This product is an article pursuant to 29 CFR 1910.1200 and, as such, is not subject to the OSHA

Hazard Communication Standard.Potential health effects

Eyes Direct contact with eyes may cause temporary irritation.Skin Health injuries are not known or expected under normal use.Inhalation Health injuries are not known or expected under normal use.Ingestion Ingestion is not likely to be a primary route of occupational exposure.

Target organs Eyes. Skin.Signs and symptoms May cause temporary irritation on skin or eye contact.

3. Composition / Information on IngredientsThe manufacturer lists no ingredients as hazardous according to OSHA 29 CFR 1910.1200.Composition comments Flexible PVC compounds may contain one or more of the following ingredients that by themselves

may be considered hazardous: Organometallic Stabilizers, Phthalate Esters, Inorganic Fillers,Pigments.

4. First Aid MeasuresFirst aid procedures

Eye contact Flush eyes with water as a precaution. Get medical attention if irritation develops or persists.Skin contact Wash with water and soap as a precaution. Get medical attention if irritation develops or persists.Inhalation Not applicable.Ingestion First aid is normally not required. Ingestion of large amounts may cause gastrointestinal

symptoms.Notes to physician Treat symptomatically.

5. Fire Fighting MeasuresFlammable properties Will burn if strongly heated and when involved in fire.Extinguishing media

Suitable extinguishingmedia

Use fire-extinguishing media appropriate for surrounding materials.

Fire fightingequipment/instructions

Selection of respiratory protection for firefighting: follow the general fire precautions indicated inthe workplace.

CPH MSDS NA

1 / 4Molding Accessories for frp panels905855 Version #: 01 Revision date: 12-02-2011 Print date: 12-02-2011

Dan

Circle

Dan

Text Box

21

Hazardous combustionproducts

During fire, gases hazardous to health may be formed.

6. Accidental Release MeasuresPersonal precautions No special precautions.Environmental precautions No specific precautions.Methods for cleaning up No specific clean-up procedure noted.Other information Collect and dispose of spillage as indicated in Section 13 of the MSDS.

7. Handling and StorageHandling Do not eat, drink or smoke when using the product. Observe good industrial hygiene practices.Storage Store away from incompatible materials. Keep away from heat, sparks and open flame.

8. Exposure Controls / Personal ProtectionOccupational exposure limits No exposure limits noted for ingredient(s).Engineering controls Ventilate as needed to control airborne dust. Use explosion-proof ventilation equipment if airborne

dust levels are high.Personal protective equipment

Eye / face protection Use tight fitting goggles if dust is generated by machining operation.Skin protection Wear protective gloves, long pants and long sleeves when machining, cutting, drilling, etc.Respiratory protection Under normal conditions, respirator is not normally required. In case of inadequate ventilation or

risk of inhalation of dust, use suitable respiratory equipment with particle filter.General hygieneconsiderations

Always observe good personal hygiene measures, such as washing after handling the materialand before eating, drinking, and/or smoking. Routinely wash work clothing and protectiveequipment to remove contaminants.

9. Physical & Chemical PropertiesAppearance Finished products are 8,10, and 12 foot pieces in several shapes and colors.

Color Various.

Odor Odorless.

Odor threshold Not available.


Form Solid.

pH Not available.

Melting point Not available.

Freezing point Not available.

Boiling point Not available.

Flash point Not available.

Evaporation rate Not available.

Flammability limits in air, upper,% by volume

Not available.

Flammability limits in air, lower,% by volume

Not available.

Vapor pressure Not available.

Vapor density Not available.

Specific gravity 1.1 - 1.5 (water = 1)

Solubility (water) Insoluble.

Partition coefficient(n-octanol/water)

Not available.

Auto-ignition temperature Not available.

Decomposition temperature Not available.

10. Chemical Stability & Reactivity InformationChemical stability Stable under normal temperature conditions.

CPH MSDS NA


Dan

Circle

Dan

Text Box

22

Conditions to avoid None under normal conditions.Incompatible materials Alkalies. Strong acids. Oxidizing agents.Hazardous decompositionproducts

Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecularweight hydrocarbons.

Possibility of hazardousreactions

Hazardous polymerization does not occur.

11. Toxicological InformationAcute effects None known.Local effects Dusts may irritate the respiratory tract, skin and eyes.Sensitization Not a skin sensitizer.Carcinogenicity Not classified.Mutagenicity Not classified.Reproductive effects Not classified.

12. Ecological InformationEcotoxicity Not expected to be harmful to aquatic organisms.Persistence anddegradability

No data available.

Bioaccumulation /Accumulation

No data available.

Partition coefficient(n-octanol/water)

Not available.

Mobility in environmentalmedia

The product is insoluble in water.

13. Disposal ConsiderationsDisposal instructions Dispose of in accordance with all applicable regulations.

14. Transport InformationDOTNot regulated as dangerous goods.IATANot regulated as dangerous goods.IMDGNot regulated as dangerous goods.TDGNot regulated as dangerous goods.

15. Regulatory InformationUS federal regulations This product is an article pursuant to 29 CFR 1910.1200 and, as such, is not subject to the OSHA

Hazard Communication Standard.TSCA Section 12(b) Export Notification(40 CFR 707, Subpt. D)

Not regulated.CERCLA (Superfund) reportable quantity (lbs) (40 CFR 302.4)

NoneSuperfund Amendments and Reauthorization Act of 1986 (SARA)

Hazard categories Immediate Hazard - NoDelayed Hazard - NoFire Hazard - NoPressure Hazard - NoReactivity Hazard - No

Section 302 extremelyhazardous substance (40CRF 355, Appendix A)

No

CPH MSDS NA


Dan

Circle

Dan

Text Box

23

Section 311/312 (40 CFR370)

No

Drug EnforcementAdministration (DEA) (21 CFR1308.11-15)

Not controlled

WHMIS status Non-controlled

Inventory statusCountry(s) or region Inventory name On inventory (yes/no)*

NoAustralia Australian Inventory of Chemical Substances (AICS)NoCanada Domestic Substances List (DSL)NoCanada Non-Domestic Substances List (NDSL)NoChina Inventory of Existing Chemical Substances in China (IECSC)NoEurope European Inventory of Existing Commercial Chemical

Substances (EINECS)NoEurope European List of Notified Chemical Substances (ELINCS)NoJapan Inventory of Existing and New Chemical Substances (ENCS)NoKorea Existing Chemicals List (ECL)NoNew Zealand New Zealand InventoryNoPhilippines Philippine Inventory of Chemicals and Chemical Substances

(PICCS)NoUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory

*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)

State regulations This product does not contain a chemical known to the State of California to cause cancer, birthdefects or other reproductive harm.

16. Other InformationHMIS® ratings Health: 0

Flammability: 0Physical hazard: 0

NFPA ratings Health: 0Flammability: 0Instability: 0

Disclaimer The information in the sheet was written based on the best knowledge and experience currentlyavailable.

Issue date 12-02-2011

CPH MSDS NA


Dan

Circle

Dan

Text Box

24

INSTALLED WITH ACROVYN

INTERIORS HEAVY DUTY

WATER BASED MASTIC ADHESIVE

ACROVYN

WALL COVERING

BASE (BY OTHERS)

FLOOR (BY OTHERS)

WAINSCOT TRIM

NO LESS THAN 1"

RECOMMENDED

ABOVE FINISH FLOOR

FOR FIELD

VARIATION

3/8"

[9.6mm]

3/8"

[9.5mm]

3/8"

[9.5mm]

3/8"

[9.1mm]

3/8"

[9.5mm]

6696 Route 405 Highway, Muncy PA 17756

(800) 233-8493 Fax (570) 546-4692 www.c-sgroup.com

DOC#: TS-930- ISSUE DATE: REV DATE:08/03/10346N 10/06/14

COLOR:____________________________________________

COLOR TO BE SELECTED FROM ONE OF C/S STANDARD COLORS. CHAMELEON

PATTERNS/COLORS ARE AVAILABLE ON SHEETS ONLY. TRIMS ARE ONLY

AVAILABLE IN SOLID/BASE COLORS.

TEXTURE:__________________________________________

SUEDE TEXTURE IS STANDARD. ADDITIONAL TEXTURES AVAILABLE UPON

REQUEST. ADDITIONAL TEXTURES MAY EFFECT PRICE.

.040" ACROVYN WALL COVERING

AT PARTIAL HEIGHT

WITH ACROVYN TRIMS

NOTES:

1. STANDARD SHEET SIZES ARE 48" X 96" OR 48" X 120". TEXTURED SHEET

SIZES ARE 43" X 90" OR 43" X 114".

2. CHAMELEON PATTERN DIRECTION IS PARALLEL TO THE 96" OR 120" SIDE OF A

STANDARD SHEET, OR 90" OR 114" SIDE OF A TEXTURED SHEET.

3. ACROVYN TRIMS SUPPLIED IN 10'-0" LENGTHS.

MATERIAL

QTY.

REQ'D

48" X 96"

48" X 120"

COLOR:__________________

QTY.:_____________________

OUTSIDE CORNER TRIM

(25N032xxx)

COLOR:__________________

QTY.:_____________________

INSIDE CORNER TRIM

(25N035xxx)

COLOR:__________________

QTY.:_____________________

VERTICAL JOINT TRIM

(25N033xxx)

COLOR:__________________

QTY.:_____________________

WAINSCOT TRIM

(25N036xxx)

Dan

Circle

Dan

Text Box

25


Last Updated February 25, 2011

Page 1 of 4

Product Name: New Acrovyn 4000 D Product Numbers: 1BPM, 1BPMS, 1BPMP Synonyms: Molded/Extruded Product Company Identification: Construction Specialties, Inc. 6696 State Route 405 Muncy, PA 17756 Information Phone: 800-233-8493 Emergency phone: Chemtec 800-476-9300

CONTAINING: HAZARDOUS AND/OR REGULATED COMPONENTS

Chemical Name Amount CAS Number

Hazardous OSHA PEL (ppm)

ACGIH TLV (ppm)

All Non-Hazardous Ingredients

100% Not

Required No Not Listed Not Listed

COMPOSITION NOTE: This is a molded/extruded product containing no hazardous materials. This product is classified as an “article” according to Title 29 of the Code of Federal Regulations, OSHA Part 1910.1200. “Article means a manufactured item other than a fluid or particle, which is formed to a specific shape or design during manufacture which has end use function dependent in whole or in part upon its shape or design during end use, and which under normal conditions of use does not release more than very small quantities or trace amounts of a hazardous chemical, and does not pose a physical hazard or health risk to employees.” This product is odorless, stable, and poses no immediate hazard to health. California Prop 65: This product does not contain an ingredient(s), above the safe harbor limits, which are

known to the state of California to cause cancer, birth defects, or other reproductive harm. HAZARDS DISCLOSURE: This product does not contain known hazardous materials in reportable levels as

defined by the OSHA Hazard Communication Standard 29 CFR 1910.1200 except as listed above. As defined under Sara 311 and 312, this product does not contain known hazardous materials.

EMERGENCY OVERVIEW NON-HAZARDOUS PRODUCT WHEN USED AS INTENDED..

HMIS/NFPA Rating: See Section 16 POTENTIAL HEALTH EFFECTS INHALATION: This product does not represent an inhalation hazard. However, dust produced by cutting, sanding, grinding or if dust is produced by any other operation may irritate respiratory tract. INGESTION: This product does not represent an ingestion hazard.

SKIN CONTACT: Dust may irritate skin on prolonged or repeated contact. EYE CONTACT: Dust produced by cutting, sanding, grinding or if dust is produced by any other operation may irritate eyes. CHRONIC EXPOSURE: No Chronic effects known or reported

1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

3. HAZARDS IDENTIFICATION

2. COMPOSITION / INFORMATION ON INGREDIENTS

Dan

Circle

Dan

Text Box

26



Page 2 of 4

AGGRAVATION OF PRE-EXISTING CONDITIONS: None known. CARCINOGENICITY: This product and its components are not listed by the NTP, IARC, or regulated by OSHA as carcinogens.

INHALATION FIRST AID: If a respiratory problem develops from vapors. Remove victim to fresh air and provide oxygen if breathing is difficult. Get medical attention. If the victim has difficulty breathing or tightness of the chest, is dizzy, vomiting or unresponsive, give 100% oxygen with rescue breathing or CPR as required and transport to the nearest medical facility.

SKIN CONTACT FIRST AID: After handling material wash skin with plenty of soap and water. Remove contaminated clothing and shoes. Get medical attention if irritation occurs or persists.

EYE CONTACT FIRST AID: If dust comes in contact with eyes, check for and remove any contact lenses. Immediately flush eyes with plenty of water for at least 15 minutes, lifting lower and upper eyelids occasionally. Seek medical attention if irritation persists.

INGESTION FIRST AID: Never give anything by mouth to an unconscious person. Call a physician or poison control.

STATEMENT OF PRACTICAL TREATMENT: Treat symptoms.

FLAMMABLE PROPERTIES: AUTO IGNITION TEMPERATURE: Not Established FLASH POINT: Not applicable FLAMMABLE LIMITS IN AIR, % by Volume: lel: NA; uel: NA EXTINGUISHING MEDIA: Carbon dioxide, water, sand FIRE & EXPLOSION HAZARDS: Combustion will produce carbon dioxide and carbon monoxide. SPECIAL INFORMATION:

In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full facepiece operated in the pressure demand or other positive pressure mode. Do not approach containers suspected to be hot.

SPILL: Pick-up for re-use or recycle.

HANDLING (PERSONNEL): Handle in accordance with good hygiene and safety procedures. STORAGE PRECAUTIONS: None Established.

AIRBORNE EXPOSURE LIMITS: General Dust exposure Limits apply VENTILATION SYSTEM: No special ventilation required. PERSONAL RESPIRATORS (NIOSH APPROVED): None required. SKIN PROTECTION: Observe good industrial hygiene practices.

5. FIRE FIGHTING MEASURES

6. ACCIDENTAL RELEASE MEASURES

7. HANDLING AND STORAGE

8. EXPOSURE CONTROLS / PERSONAL PROTECTION

4. FIRST AID MEASURES

Dan

Circle

Dan

Text Box

27



Page 3 of 4

EYE PROTECTION: Use Good safety practices.

FORM: Solid COLOR: VariousColors

ODOR: Odorless BOILING POINT: Not Established

SOLUBILITY IN WATER: Negligible SPECIFIC GRAVITY: 1.27 at 23 °C

MELTING/FREEZING POINT: Not Established EVAPORATION RATE (BuAc=1): Not Applicable

AUTO IGNITION TEMPERATURE: Not Established FLASH POINT: Not Applicable

pH: Not Applicable VAPOR PRESSURE: Negligible

STABILITY: Product is considered stable. CONDITIONS TO AVOID: Heat, flames, ignition sources and incompatibles. POLYMERIZATION: Hazardous polymerization will not occur. INCOMPATIBILITY WITH OTHER MATERIALS: None Known DECOMPOSITION: Carbon dioxide and carbon monoxide may form when heated to decomposition.

Toxicological Data: No known health effects connected with long term use or contact with these products.

ENVIRONMENTAL FATE: This material is not expected cause long term adverse effects to the environment. ENVIRONMENTAL TOXICITY: No Data

WASTE DISPOSAL: Dispose of in accordance with federal, state and local requirements.

Domestic (Land, D.O.T.), International (Water, I.M.O.), International (Air, I.C.A.O.)

CLASS: None PRODUCT LABEL: New Acrovyn 4000 D UN NUMBER: None PACKING GROUP: None D.O.T. SHIPPING NAME: Non-regulated Material. PRODUCT RQ (LBS): None ERG Guide Number: None Quantity Limitations: Passenger aircraft: N/A Cargo aircraft only: N/A

9. PHYSICAL AND CHEMICAL PROPERTIES

10. STABILITY AND REACTIVITY

11. TOXICOLOGICAL INFORMATION

12. ECOLOGICAL INFORMATION

13. DISPOSAL CONSIDERATIONS

14. TRANSPORTATION INFORMATION

Dan

Circle

Dan

Text Box

28



Page 4 of 4

0 0

0

FEDERAL REGULATORY STATUS

Federal, State & International Regulations SARA 302 -SARA 313- CERCLA RCRA TSCA Ingredient RQ TPQ List Chemical Catalog 261.33 8(d) All Components NO NO NO NO NO NO NO

Chemical Weapons Convention: No TSCA 12(b): No CDTA: No SARA 311/312: Acute: No; Chronic: No; Fire: No; Pressure: No; Reactivity: No (Mixture / Liquid) Australian Hazchem Code: None allocated Poison Schedule: None allocated. WHMIS: This MSDS has been prepared according to the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR. This material or all of its components are listed on the Inventory of Existing Chemical Substances under the Toxic Substance Control Act (TSCA). This material or all of its components are listed on the Canadian Domestic Substances List (DSL). This material or all of its components are listed (or considered as having been notified) on the European Inventory of Existing Chemical Substances (EINECS). Other inventory lists: ENCS (Japan), Korea, Australia, China (Draft), PICCS (Philippines), Japan (ENCS). NFPA Ratings: Health: 2 Flammability: 0 Reactivity: 0

National Fire Protection Association (NFPA):

NFPA/HMIS Definitions: 0-Least, 1-Slight, 2-Moderate, 3-High, 4-Extreme Prepared By: Paul Eigbrett (MSDS Authoring Services) Part Number: -- Approval Date: February 25, 2011 Supersedes Date: New

ADDITIONAL INFORMATION:

The data in this Material Safety Data Sheet relates only to the specific material designated herein. It does not relate to use in combination with any other material or in any process. This Material Safety Data Sheet (MSDS) has been reviewed to fully comply with the guidance contained in the ANSI MSDS standard (ANSI Z400.1-2004)

This information is furnished without warranty, expressed or implied, except that it is accurate to the best knowledge of Construction Specialties, Inc The data on this sheet are related only to the specific material designated herein. Construction Specialties, Inc. assumes no legal responsibility for use or reliance upon these data. To the best of our knowledge, the information contained herein is accurate. However, neither the above named supplier nor any of its subsidiaries assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.

END OF MSDS

15. REGULATORY INFORMATION

16. OTHER INFORMATION

Dan

Circle

Dan

Text Box

29

ACROVYN HEAVY-DUTY WATER-BASE MASTIC


SECTION I – PRODUCT IDENTIFICATION

Manufactured for Construction Specialties Group

By Super-Tek Products, Inc.

25-44 Borough Place, Woodside, NY 11377

Telephone #: 718-278-7900

Emergency Phone #: 718-278-7900

Generic ID: Water-base mastic for Rigid Plastic Wallcovering

Product Identity: Acrovyn Heavy-Duty Water-Base Mastic

Date Prepared:1/01/11

SECTION II – INGREDIENTS

Ingredient Name CAS Number Percent Exposure Limits

Water 7732-18-5 37-39 N/A

Acrylic Polymer N/A 61-63 5000 ppm (TLV)

* Other Non-Hazardous Ingredients considered a Trade Secret

SECTION III – PHYSICAL DATA

Initial Boiling Point: 212°F.

Vapor Pressure: Same as water.

Vapor Density (Air=1.0): Same as water.

Specific Gravity: .98-1.00.

Percent Volatiles: 37-39.0%.

VOC Content: 0%.

SECTION IV – FIRE AND EXPLOSION DATA

Flash Point: N/A.

Explosive Limit (Product): N/A.

Extinguishing Media: None to avoid.

SPECIAL FIRE FIGHTING PROCEDURES: None.

UNUSUAL FIRE & EXPLOSION HAZARDS: None.

SECTION V – HEALTH HAZARD DATA

Permissible Exposure Level: N/A.

Threshold Limit Value: N/A.

EFFECTS OF EXPOSURE:

Skin: Possible mild irritation.

Eyes: Possible mild irritation.

Inhalation: None known.

FIRST AID:

Skin: Soap and water.

Eyes: Flush with water, lifting upper and lower lids occasionally.

Inhalation: If affected, remove individual to fresh air. Use only in

well ventilated areas.

Ingestion: Do not induce vomiting. Call physician or transport to

an emergency facility.

SECTION VI – REACTIVITY DATA

Stability: Stable.

Incompatibility: None.

Hazardous Decomposition: None.

Hazardous Polymerization: None.

Conditions to Avoid: None Known.

SECTION VII – SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED

OR SPILLED: Absorb liquid on paper, vermiculite, floor

absorbent, or other absorbent material. Solidified materials

accepted for landfill disposal in most locations. Check all local,

state, and federal regulations.

SECTION VIII – PROTECTIVE EQUIPMENT

Ventilation: Open all available windows and entrances to insure

good ventilation.

Respirator Protection: None needed.

Protective Gloves: If sensitive.

Eye protection: Wear glasses or protective goggles to avoid

splashes.

Other Protective Equipment: None required.

WASH HANDS THORUGHLY WITH SOAP AND WATER.

SECTION IX – SPECIAL PRECAUTIONS

Protect from freezing. Use only in applications as stated on the

label. Do not take internally. Close container after each use. Avoid

skin and eye contact.

Ventilation with fresh air, including open doors and windows

should be observed during any flooring installation. Operate HVAC

systems at 100% fresh air intake before, during and after

installation to eliminate lingering odors or particulate matter.

The information accumulated herein is believed to be accurate but

is not warranted to be whether originating with company or not.

Recipients are advised to confirm in advance of need that the

information is current, applicable and suitable to their

circumstances.

KEEP OUT OF REACH OF CHILDREN

Dan

Circle

Dan

Text Box

30

Product Information

SiliconeSealants

Dow Corning® 790 Silicone Building Sealant

FEATURES & BENEFITS

Excellent performance even in building joints that experience extreme movement

Suitable for new and remedial construction

Extension/compression capability of +100/-50 percent

Excellent weathering properties and resistance to sunlight, rain, snow, and temperature extremes

Excellent unprimed adhesion to masonry, concrete substrates

Easy application over a wide temperature range

COMPOSITION

Ultra-low-modulus, one-part, neutral-cure silicone sealant

Ultra-low-modulus sealant for new and remedial construction joint sealing applications

APPLICATIONSDow Corning® 790 Silicone Building Sealant offers outstanding unprimed adhesion to masonry and is particularly effective for sealing expansion and control joints, precast concrete panel joints, Exterior Insulation and Finish Systems (EIFS) joints, curtainwall joints, mullion joints, stone pavers, and many other construction joints. When used in accordance with Dow Corning application and testing recommendations, the sealant forms a durable, flexible, watertight bond with many common building materials, including combinations of stone, concrete, masonry, granite, marble, aluminum, painted substrates, and glass.

TYPICAL PROPERTIESSpecification Writers: These values are not intended for use in preparing specifications. Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.

Test Property Unit Result

As Supplied

ASTM C 679 Tack-Free Time, 50% RH hours 1

Curing Time, 50% RH, at 25°C (77°F), 3/8" depth

days 7-14

Full Adhesion, cured joint days 14-21

ASTM D 2202 Flow, Sag, or Slump None

CTM 98 Working Time minutes 10-20

EPA Method 24 VOC Content1, maximum g/L 23

As Cured – After 7 days at 25°C (77°F) and 50% RH

ASTM C 661 Durometer Hardness, Shore A points 15

ASTM D 412 Tensile Strength, maximum psi (kg/mm2) 100 (0.070)

ASTM C 794 Peel Strength lb/in (kg/cm) 25 (4.46)

ASTM C 1135 Tensile

at 25% extension

at 50% extension

psi (kg/mm2)

psi (kg/mm2)

15 (0.010)

20 (1.015)

ASTM C 719 Joint Movement Capabilities

Extension/Compression % +100/-50

ASTM C 1248 Staining, various substrates None

*ASTM: American Society for Testing and Materials.CTMs (Corporate Test Methods) correspond to standard ASTM tests in most instances. Copies of CTMs are available upon request.

1Based on South Coast Air Quality Management District of California. Maximum VOC is listedboth inclusive and exclusive of water and exempt compounds. For a VOC data sheet for a specific sealant color, please send your request to [email protected].

Dan

Circle

Dan

Text Box

31

DOW CORNING CORPORATION Material Safety Data Sheet

Page: 1 of 8 Version: 2.0

Revision Date: 2014/07/15 DOW CORNING(R) 790 SILICONE BLDG SEALANT, CUSTOM COLOR

1. PRODUCT AND COMPANY IDENTIFICATION Dow Corning Corporation South Saginaw Road Midland, Michigan 48686

24 Hour Emergency Telephone:

Customer Service: Product Disposal Information:

CHEMTREC:

(989) 496-5900 (989) 496-6000 (989) 496-6315 (800) 424-9300

MSDS No.: 04110631

Revision Date: 2014/07/15

Generic Description: Silicone Sealant Physical Form: Paste

Color: See product name Odor: Amine-like odor

NFPA Profile:

Health 2 Flammability 1 Instability/Reactivity 0

Note: NFPA = National Fire Protection Association 2. HAZARDS IDENTIFICATION

POTENTIAL HEALTH EFFECTS

Acute Effects Eye:

Direct contact may cause severe irritation.

Skin:

May cause moderate irritation.

Inhalation:

Irritates respiratory passages very slightly.

Oral:

Low ingestion hazard in normal use.

Prolonged/Repeated Exposure Effects Skin:

Repeated or prolonged exposure may irritate seriously.

Inhalation:

No known applicable information.

Oral:

Overexposure by ingestion may injure the following organ(s): Bone marrow.

Other Health Effects This product contains a chemical(s) that has the following effect(s): Reproductive Toxicity Carcinogenicity See Section 11 for specific details.

Dan

Circle

Dan

Text Box

32




Signs and Symptoms of Overexposure


Medical Conditions Aggravated by Exposure


The above listed potential effects of overexposure are based on actual data, results of studies performed upon similar compositions, component data and/or expert review of the product. Please refer to Section 11 for the detailed toxicology information.

3. COMPOSITION/INFORMATION ON INGREDIENTS

CAS Number Wt % Component Name

87855-59-2 1.0 - 5.0 MethylVinyl Bis(N-ethylacetamido)Silane

68952-53-4 1.0 - 5.0 Dimethyl, methylethyl-N-hydroxyethamine siloxane

68186-85-6 <1.0 Cobalt titanite green spinel

The above components are hazardous as defined in 29 CFR 1910.1200.

4. FIRST AID MEASURES Eye:

Immediately flush the contaminated eye(s) with lukewarm, gently flowing water for 15 - 20 minutes while holding the eyelid(s) open. If contact lens is present, DO NOT delay irrigation or attempt to remove the lens. Take care not to rinse contaminated water into the unaffected eye or onto the face. Immediately obtain medical attention.

Skin: As quickly as possible remove contaminated clothing, shoes and leather goods (e.g. watchbands, belts). Quickly and gently blot or brush away excess chemical. Immediately flush with lukewarm gently flowing water for 15 minutes. Completely decontaminate clothing, shoes and leather goods before reuse or discard. Obtain medical attention.

Inhalation: If symptoms are experienced remove source of contamination or move victim to fresh air. If irritation persists, obtain medical advice.

Oral: If irritation or discomfort occur, obtain medical advice.

Notes to Physician: Treat according to person's condition and specifics of exposure.

5. FIRE FIGHTING MEASURES

Dan

Circle

Dan

Text Box

33




Flash Point:

Not applicable.

Autoignition Temperature:

Not determined.

Flammability Limits in Air:

Not determined.

Extinguishing Media:

On large fires use dry chemical, foam or water spray. On small fires use carbon dioxide (CO2), dry chemical or water spray. Water can be used to cool fire exposed containers.

Fire Fighting Measures:

Self-contained breathing apparatus and protective clothing should be worn in fighting large fires involving chemicals. Determine the need to evacuate or isolate the area according to your local emergency plan. Use water spray to keep fire exposed containers cool.

Unusual Fire Hazards:

None.

6. ACCIDENTAL RELEASE MEASURES Containment/Clean up:

Observe all personal protection equipment recommendations described in Sections 5 and 8. Wipe up or scrape up and contain for salvage or disposal. Clean area as appropriate since spilled materials, even in small quantities, may present a slip hazard. Final cleaning may require use of steam, solvents or detergents. Dispose of saturated absorbant or cleaning materials appropriately, since spontaneous heating may occur. Local, state and federal laws and regulations may apply to releases and disposal of this material, as well as those materials and items employed in the cleanup of releases. You will need to determine which federal, state and local laws and regulations are applicable. Sections 13 and 15 of this MSDS provide information regarding certain federal and state requirements.

Note: See Section 8 for Personal Protective Equipment for Spills. Call (989) 496-5900, if additional information is required.

7. HANDLING AND STORAGE Use with adequate ventilation. Avoid eye contact. Avoid skin contact. Do not take internally. Use reasonable care and store away from oxidizing materials. This material in its finely divided form presents an explosion hazard. Follow NFPA 654 (for chemical dusts) or 484 (for metal dusts) as appropriate for managing dust hazards to minimize secondary explosion potential.

8. EXPOSURE CONTROLS / PERSONAL PROTECTION Component Exposure Limits CAS Number Component Name Exposure Limits

Dan

Circle

Dan

Text Box

34




68186-85-6 Cobalt titanite green spinel

Observe limits: Nickel - OSHA PEL and ACGIH TLV: TWA 1 mg/m3. Cobalt - OSHA PEL (final rule) and ACGIH TLV: TWA 0.05 mg/m3.

Engineering Controls Local Ventilation: None should be needed. General Ventilation: Recommended.

Personal Protective Equipment for Routine Handling Eyes:

Use chemical worker's goggles.

Skin:

Wash at mealtime and end of shift. If skin contact occurs, change contaminated clothing as soon as possible and thoroughly flush affected areas with cool water. Chemical protective gloves are recommended.

Suitable Gloves:

Avoid skin contact by implementing good industrial hygiene practices and procedures. Select and use gloves and/or protective clothing to further minimize the potential for skin contact. Consult with your glove and/or personnel protective equipment manufacturer for selection of appropriate compatible materials.

Inhalation:

No respiratory protection should be needed.

Suitable Respirator:

None should be needed.

Personal Protective Equipment for Spills Eyes:

Use chemical worker's goggles.

Skin:

Wash at mealtime and end of shift. If skin contact occurs, change contaminated clothing as soon as possible and thoroughly flush affected areas with cool water. Chemical protective gloves are recommended.

Inhalation/Suitable Respirator:

No respiratory protection should be needed.

Precautionary Measures: Avoid eye contact. Avoid skin contact. Do not take internally. Use reasonable care.

Note: These precautions are for room temperature handling. Use at elevated temperature or aerosol/spray applications may require added precautions.

9. PHYSICAL AND CHEMICAL PROPERTIES

Physical Form:

Paste

Color: See product name Odor: Amine-like odor

Specific Gravity @ 25°C: 1.48

Dan

Circle

Dan

Text Box

35




Viscosity: Not determined. Freezing/Melting Point: Not determined.

Boiling Point: Not determined. Vapor Pressure @ 25°C: Not determined.

Vapor Density: Not determined. Solubility in Water: Not determined.

pH: Not determined. Volatile Content: Not determined.

Flash Point: Not applicable. Autoignition Temperature: Not determined. Flammability Limits in Air: Not determined.

Note: The above information is not intended for use in preparing product specifications. Contact Dow Corning before writing specifications.

10. STABILITY AND REACTIVITY Chemical Stability:

Stable.

Hazardous Polymerization:

Hazardous polymerization will not occur.

Conditions to Avoid:

None.

Materials to Avoid:

Oxidizing material can cause a reaction.

Hazardous Decomposition Products Thermal breakdown of this product during fire or very high heat conditions may evolve the following decomposition products: Carbon oxides and traces of incompletely burned carbon compounds. Metal oxides. Formaldehyde. Silicon dioxide. Nitrogen oxides. Quartz. Sulfur oxides.

11. TOXICOLOGICAL INFORMATION Special Hazard Information on Components Carcinogens

CAS Number

Wt %

Component Name

68186-85-6

<1.0 Cobalt titanite green spinel

IARC Group 2B - Possibly Carcinogenic to Humans. Cobalt compound.

Reproductive Toxicity

CAS Number

Wt %

Component Name

Dan

Circle

Dan

Text Box

36




87855-59-2

1.0 - 5.0 MethylVinyl Bis(N-ethylacetamido)Silane

Evidence of reproductive effects in laboratory animals.

12. ECOLOGICAL INFORMATION Environmental Fate and Distribution

Complete information is not yet available.

Environmental Effects


Fate and Effects in Waste Water Treatment Plants


Ecotoxicity Classification Criteria Hazard Parameters (LC50 or EC50) High Medium Low Acute Aquatic Toxicity (mg/L) <=1 >1 and <=100 >100 Acute Terrestrial Toxicity <=100 >100 and <= 2000 >2000 This table is adapted from "Environmental Toxicology and Risk Assessment", ASTM STP 1179, p.34, 1993. This table can be used to classify the ecotoxicity of this product when ecotoxicity data is listed above. Please read the other information presented in the section concerning the overall ecological safety of this material.

13. DISPOSAL CONSIDERATIONS RCRA Hazard Class (40 CFR 261) When a decision is made to discard this material, as received, is it classified as a hazardous waste? No State or local laws may impose additional regulatory requirements regarding disposal. Call (989) 496-6315, if additional information is required.

14. TRANSPORT INFORMATION DOT Road Shipment Information (49 CFR 172.101) Not subject to DOT. Ocean Shipment (IMDG) Not subject to IMDG code. Air Shipment (IATA)

Dan

Circle

Dan

Text Box

37




Not subject to IATA regulations. Call Dow Corning Transportation, (989) 496-8577, if additional information is required.

15. REGULATORY INFORMATION Contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200. TSCA Status: All chemical substances in this material are included on or exempted from listing on the TSCA

Inventory of Chemical Substances.

EPA SARA Title III Chemical Listings Section 302 Extremely Hazardous Substances (40 CFR 355): None. Section 304 CERCLA Hazardous Substances (40 CFR 302):

None.

Section 311/312 Hazard Class (40 CFR 370):

Acute: Yes Chronic: Yes

Fire: No Pressure: No Reactive: No

Section 313 Toxic Chemicals (40 CFR 372):

CAS Number

Wt %

Component Name

8007-18-9 <=1.6 Antimony nickel titanium oxide yellow

68186-85-6 0.32 Cobalt titanite green spinel

Note: Chemicals are listed under the 313 Toxic Chemicals section only if they meet or exceed a reporting threshold. Supplemental State Compliance Information California

Warning: This product contains the following chemical(s) listed by the State of California under the Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65) as being known to cause cancer, birth defects or other reproductive harm. CAS Number

Wt %

Component Name

8007-18-9 <=1.6000 Antimony nickel titanium oxide Carcinogenic.

Dan

Circle

Dan

Text Box

38




yellow

New Jersey

CAS Number

Wt %

Component Name

1317-65-3 40.0 - 60.0 Limestone

70131-67-8 40.0 - 60.0 Dimethyl siloxane, hydroxy-terminated

13463-67-7 <=2.4 Titanium dioxide

87855-59-2 1.0 - 5.0 MethylVinyl Bis(N-ethylacetamido)Silane

8007-18-9 <=1.6 Antimony nickel titanium oxide yellow

1333-86-4 <=0.8 Carbon black

14808-60-7 <1.0 Quartz

68186-85-6 <1.0 Cobalt titanite green spinel

Pennsylvania CAS Number

Wt %

Component Name

1317-65-3 40.0 - 60.0 Limestone

70131-67-8 40.0 - 60.0 Dimethyl siloxane, hydroxy-terminated

13463-67-7 <=2.4 Titanium dioxide

16. OTHER INFORMATION Prepared by: Dow Corning Corporation These data are offered in good faith as typical values and not as product specifications. No warranty, either expressed or implied, is hereby made. The recommended industrial hygiene and safe handling procedures are believed to be generally applicable. However, each user should review these recommendations in the specific context of the intended use and determine whether they are appropriate.

(R) indicates Registered Trademark

Dan

Circle

Dan

Text Box

39

SPECIFICATIONSCrane Composites panels are manufactured by a continuous laminating process in lengths as required.

COMPOSITIONReinforcement: Random chopped fi berglass.Resin Mix: Modifi ed polyester copolymer and inorganic fi llers and pigments.

FINISHED PANEL QUALITY1. Panels have a wear side with a smooth, decorative fi nish and the

backside is smooth. Backside imperfections, which do not affect functional properties, are not cause for rejection.

2. Physical properties shall be as set forth in Table 1.3. Dimensions shall be as specifi ed on purchase order, subject to the

following tolerances:Width: ±1/8" (±3.2 mm)Length: ±1/8" (±3.2 mm) up to 12' (3.7 m)Squareness: ±1/8" (3.2 mm) in 48" (1.2 m) of width

4. Product quality standards and tolerances for panel weight and thickness shall be as set forth in Crane Composites' Quality Control Procedures/Standards which are available on request.

5. Panels shall be installed in accordance with manufacturer's guidelines as set forth in the Crane Composites Installation Guide (Form #6876).

CERTIFICATIONS1. Meets USDA/FSIS requirements 2. FRP does not support mold or mildew

(per ASTM D3273 and ASTM D3274)3. This panel has earned GREENGUARD® SELECT

Education and GREENGUARD® SELECT Healthcare Certifi cation. (Certifi cate # 90154-03) www.greenguard.org

4. DESIGNS Class A (IPSA) - Meets minimum requirements of major model building codes for Class A interior wall and ceiling fi nishes of fl ame spread ≤ 25, smoke developed 450 or less (per ASTM E-84)

5. DESIGNS Class C (IPSC) Meets minimum requirements of major model building codes for Class C interior wall and ceiling fi nishes of fl ame spread ≤ 200, smoke developed 450 or less (per ASTM E-84)

6. CAN/ULC-S102 test results: Flame spread:125, Smoke developement: 260, Per report 09-002-528 dated 8-25-2009

7. Crane Composites certifi es that Innovative Finishes DESIGNS (IPSA) meet the requirements of ASTM D5319. Classifi cation Class A - Flame spread 0 to 25, smoke development index of

450 or less per ASTM E 84.Grade 6: 0.081 to 0.099 n. (2.06 to 2.51mm); 0.090 in. nominal (2.29mm).Tolerances: Width and Length: + .125 in (3.175mm) up to and including 12 ft.

Squareness: + .125 in (3.175mm) Thickness: + 10% Camber: + .25 in (6.35mm)

8. Crane Composites certifi es that Innovative Finishes DESIGNS (IPSC) meet the requirements of ASTM D5319. Classifi cation Class C - Flame spread 76 to 200, smoke development index of

450 or less per ASTM E 84.Grade 6: 0.081 to 0.099 n. (2.06 to 2.51mm); 0.090 in. nominal (2.29mm).Tolerances: Width and Length: ± .125 in (3.175mm) up to and including 12 ft. Squareness: ± .125 in (3.175mm) Thickness: ±10% Camber: ± .25 in (6.35mm)

FABRICATING RECOMMENDATIONSNote: Protect your eyes with goggles; cover your nose and mouth with a fi lter mask; cover exposed skin when cutting CCI panels.Hand Fabricating: Drilling—High speed drill bit (60° cutting angle, with 12°-15° clearance) or hole saw. Cutting: Sheet metal shears or circular saw with reinforced carborundum or carbide-tipped blade.Production Fabricating: Use carbide-tipped tools. Straight cuts can be sheared (90° cutting edge with 0.002" [0.05 mm] clearance) or sawed. For irregular cuts, use die punch or band saw. Cleaning Instructions: Available from CCI.

STORAGEAll Crane Composites FRP products should be stored indoors.

SERVICEABLE TEMPERATURE RANGEPanels will perform in temperatures from -40°F (-40°C) to 130°F (55°C). For use in environments beyond this range contact Crane Composites for recommendations.

LIMITATIONSNear Heat Source: Crane Composites panels will discolor when installed behind or near any heat source which radiates temperatures exceeding 130°F (55°C), such as cookers, ovens, and deep fryers. Do not install near a heat source. Uneven Surface: Installation over uneven concrete block walls may result in areas of delamination and bulging.Note: Due to the specialty custom nature of the DESIGNS and DESIGNS 4U production process, color variance from lot to lot production will occur. Panels will not be the exact same color from run to run. ORDER ENOUGH PANELS TO COMPLETE A ROOM INSTALLATION.

NOTICEPanels will provide a clean, aesthetically-pleasing fi nished installation. However, by nature, fi berglass reinforced plastic paneling may occasionally have small areas that are aesthetically unacceptable for use. Panels should be inspected on-site prior to installation. If any portion of material does not provide an acceptable appearance, Crane Composites should be notifi ed at once. Upon verifi cation of unacceptability, that portion of material will be replaced by Crane Composites. Crane Composites' sole responsibility is for the replacement of defective materials but not for labor or other handling or installation expenses.

RELATED INFORMATIONFor scratch touch ups see document #7507

Form 7505 | Rev. 07 | 10.14 | (7347)

FLAME SPREAD AND SMOKE DEVELOPMENT RATINGSThe numerical fl ame spread and smoke development ratings are not intended to refl ect alleged hazards presented by Crane Composites products under actual fi re conditions and this product has not been tested by Crane Composites except as set forth below. These ratings are determined by small-scale tests conducted by Underwriters Laboratories and other independent testing facilities using the American Society for Testing and Materials E-84 test standard (commonly referred to as the “Tunnel Test”). CRANE COMPOSITES PROVIDES THESE RATINGS FOR MATERIAL COMPARISON PURPOSES ONLY. Like other organic building materials (e.g. wood), panels made of fi berglass reinforced plastic resins will burn. When ignited, FRP may produce dense smoke very rapidly. All smoke is toxic. Fire safety requires proper design of facilities and fi re suppression systems, as well as precautions during construction and occupancy. Local codes, insurance requirements and any special needs of the product user will determine the correct fi re-rated interior fi nish and fi re suppression system necessary for a specifi c installation. We believe all information given is accurate, without guarantee. Since conditions of use are beyond our control, all risks are assumed by the user. Nothing herein shall be construed as a recommendation for uses which infringe on valid patents or as extending a license under valid patents. www.astm.org/Standards/E84.htm.

www.FRP.com | 1.800.435.0080 | 1.815.467.8666 (fax) | [email protected] Composites is the manufacturer of Glasbord, Sanigrid II and a variety of other fi berglass reinforced plastic (FRP) composite wall panels. Inspired by the Kemlite tradition, Crane Composites has over 55 years of experience in Commercial Building Products and is a recognized industry leader in FRP applications.

Dan

Circle

Dan

Text Box

40

Documents

MSDS UofW Tacoma Y-Center