8

Manufacturer: AOYUE INTERNATIONAL LIMITED Jishui Industrial Zone, Nantou, Zhongshan City, Guangdong Province, P.R.China http://www.aoyue.com

5

Instruction Manual

Thank you for purchasing the Aoyue int 486+ Multifunction smoke absorber.

Please read the manual before using the unit. Keep manual in accessible place for future reference.

Multifunction Smoke Absorber

486+

2

TABLE OF CONTENTS

Product Description …………………………………… 3

Package Inclusion …………………………………… 3

Safety Precautions …………………………………… 4

Specifications …………………………………… 5

Functions and Features ……………………………… 5

Control Panel Guide …………………………………… 5

Operating Guidelines ……………………………… …. 6

Basic Troubleshooting Guide ………………………. ….. 7

This manual is designed to familiarize and instruct the technician with the proper operation and maintenance of the equipment. The “Care and Safety Precautions” section explains the hazards of using any type of solder-ing or reworking device. Please read carefully and ob-serve the guidelines in order to maximize usage and mini-

5

BASIC TROUBLESHOOTING GUIDE

PROBLEM 1: THE UNIT HAS NO POWER 1. Check if the unit is switched ON. 2. Check the power cord and make sure there are no disconnections. 3. Verify that the unit is properly connected to the power source.

PROBLEM 2: LED LAMP IS NOT BRIGHT ENOUGH or DOES NOT TURN ON

SOLUTION: Replace battery

PROBLEM 3: OTHER PROBLEMS NOT MENTIONED IN THIS DOCUMENT SOLUTION: Contact authorized service station.

6

OPERATING GUIDELINES

REMINDERS: 1. Make sure the equipment is placed on a flat stable surface and

all the heat-generating components placed on their respective holders or stands.

2. Ensure all function switches are in the OFF position.

IMPORTANT: Please refer to the CONTROL PANEL GUIDE page

for button switches.

A. PROCEDURES 1. Plug the power cord into a grounded wall socket. The station is

protected against electrostatic discharge and must be grounded for full efficiency.

2. To switch on the fan, turn the fan switch to ON position. 3. An aluminum smoke exhaust pipe is included in the package, use

the securing ring to attach exhaust pipe to the exhaust connector. 4. The exhaust pipe can be pulled to lengthen and positioned such that

the exhaust is directed out of the work area . 5. The integrated LED lamp needs a 9V battery to work. 6. Slide open the battery cover and insert a 9 Volt battery into the

compartment. Put battery cover back in place. 7. Press the LED switch to turn ON the LED lamp, To turn OFF the

LED lamp press the LED switch again. Turn OFF LED lamp when not in use to conserve battery life.

5

PRODUCT DESCRIPTION

● With integrated LED lamp and attachable aluminum

exhaust tube to guide fumes our and away from work

area.

● Bench top fume extractor especially designed to quickly

absorb and remove the toxic gases released during the

welding process.

● Quiet yet powerful operation.

● With changeable activated carbon filter that effectively

absorbs toxins in the fumes.

● Has a unique carbon activated air filter pack that minimize

air resistance and strengthen suction power to provide

an excellent working environment.

PACKAGE INCLUSION

1 unit Int 486+Main Station 1 pc. Activated carbon filter pads 1 pc. 12 inch Aluminum tube 1 pc. Securing ring for Aluminum tubing 1 pc. Instruction Manual

4

CAUTION: Improper usage can cause serious injury to personnel and/or damage to equipment and work area. For your own safety, please observe

the following precautions.

SAFETY PRECAUTIONS

● Check each component after opening the package to make sure everything is in good condition. If there are any sus-pected damage, do not use the item and report the issue to your vendor.

● Turn OFF the main power switch and unplug the device from power source when moving the device.

● Do not strike or subject the main unit (and all its compo-nents) to physical shock. Use carefully to avoid damage to any part.

● Handle with care. - Never drop or sharply jolt the unit. - Contains delicate parts that may break if the unit is dropped. ● Make sure the equipment is always grounded. Always con-

nect power to a grounded receptacle. ● Disconnect the plug from the power source if the unit will

not be used for a long period. - Turn off power during breaks, if possible. ● Use only genuine replacement parts. - Turn off power and let the unit cool down before replacing any part. ● Do not alter the unit, specifically the internal circuitry, in any

manner.

5

SPECIFICATION

SPECIFICATION

Voltage Input : available in 110V / 220V

Dimensions: 200(w) x250 (h) x 90 (d) mm

Weight: 2Kg

Power Consumption: 25W

CONTROL GUIDE

FUNCTIONS and FEATURES

Bright LED lamp powered by 9V battery. Separate light switch and fan switch. Attachable 12 inch aluminum smoke exhaust pipe. Powerful suction, that ensures an excellent working environment. Carbon activated filter.

LED Switch

Exhaust

Connector

FAN Switch

Battery cover

5