NA-FS16G2-14G2 Panasonic Washing Machine Service Manual

CONTENTS

1.Specifications 1

2.Technical Descriptions 2

3.How to Install 3

4.Operation Instruction 4

5.Test Mode 6

6.Troubleshooting Guide 8

7.Disassembly Instructions10

8.Wiring Diagram15

9.Parts Location & Replacement Parts List16

ORDER NO. TAM1202001CE

NA-FS16G2/NA-FS14G2

2012 Panasonic Taiwan Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.

Product Color

Destination

: Sliver / White

: Panama

Page

1.Specifications

NA-FS16G2 NA-FS14G2

Power source AC 110-120 V , 60 Hz AC 110-120 V , 60 Hz

Power consumption 430 W 420 W

(Motor) Output 200 W 185 W

Laundry amount 16 kg 14 kg

Spin (Clothes load) 610 ~ 630 rpm 610 ~ 630 rpm

Pulsator (Clothes load) 60 ~ 130 rpm 60 ~ 130 rpm

Dimension(mm) Width: 640 / Depth:667 / Height:1032 Width: 640 / Depth:667 / Height:1032

Water level(L) 99 / 92 / 86 / 80 / 74 / 68 / 62 / 56 / 50 / 45 / 40 98 / 92 / 86 / 80 / 74 / 68 / 62 / 56 / 50 / 45 / 40

Standardized water consumption 190 L 185 L

Operating Water pressure 3104 - 110

6 Pa 310

4 - 110

6 Pa

Machine weight 54 kg 54 kg

Safety switch Lid and unbalance switch Lid and unbalance switch

Buzzer Cycle-end buzzer, Give an alarm Cycle-end buzzer, Give an alarm

Bleach inlet Providing Providing

Lint filter Providing Providing

Softener Dispenser Providing Providing

Auto power off Providing Providing

AccessoriesWater Supply Hose

(One each for cold and hot water)

Water Supply Hose

(One each for cold and hot water)

Water Tap Adaptor Water Tap Adaptor

Drain Hose Drain Hose

Events Model

-1-

2.Technical Explanation

2.1 The water flow of pulsator

2.2 Air Dry Course

When the tub is rotationg, it can suck dry air inlet and keep the tub dry.

Purpose to prevent the mould growth on the surface of the tub and

the outer tub.

Rotating fins on the bottom suck in water which is pumped to the upper nozzle and released as a high-pressure splash.

Bottom

Strong splashes are

A powerful motor rotates the Big Beat (BB) Flapper to create a vortex.

(1)Stream of a big horizontal rotation is made from the big outer blades of Large Pulsator. (2)The stream of a small horizontal rotation is made fromthe small blades in the center part of Large Pulsator. (3)The stream in the vertical direction made from the blades of Small Pulsator (Pulsator cap), it is pushed in the direction of the perimeter of the tub by a small horizontal rotation stream of the above-mentioned of (2), and it becomes a diagonal stream.

Top

Beat Screw

Beat Flash

Beat Tide

-2-

3.How to install

2m

29 - 980 kPa

nut.

To connect the drain hose

1.Connect the drain hose securely to the drain hose connection of the washing machine . And move the hose band next to the body. 2. Follow the limits of maximum height (1.10m) and minimum (0.70m) for installation of drain hose.

-3-

4.O

pe

rati

on

In

str

uc

tio

n

4

.1 In

dic

ato

rs a

nd

bu

tto

ns

Att

en

tio

n

: If

yo

u n

eed

to

ch

an

ge t

he

sett

ing

aft

er

the

cycle

s h

as a

lread

y s

tart

ed

, tu

rn t

he

po

wer

off

an

d t

he

n b

ack o

n.

-4-

Indic

ate

s the a

ppro

priate

wate

rlevel

accord

ing

to the laundry

am

ount.

Wate

r L

evel

/ V

olu

me In

dic

ato

r In

dic

ate

s the c

ycle

in

pro

gre

ss b

y f

lashin

g.

Pro

gre

ss In

dic

ato

r T

he p

ow

er

auto

matically

turn

s o

ff w

hen a

cours

e is f

inis

hed, or

if w

ashin

g is n

ot

beg

un w

ithin

10 m

in. tu

rnin

g the p

ow

er

on.

Po

we

r S

wit

ch

Accord

ing

to laundry

volu

me

and sta

in, you c

an s

ele

ct a

suitable

cours

e by y

ours

elf.

Pro

gra

m

Yo

u c

an

ch

oo

se th

e

finis

hin

g tim

e e

ither

aft

er

2 to 2

4 h

ours

e.

Re

se

rve

The lam

p w

ill lig

ht

wh

en

Child

lo

ck

mo

de

is s

et.

Ch

ild

lo

ck

Sett

ing

can b

e c

hang

ed

accord

ing

to y

our

pre

fere

nce.

Wate

r L

evel

C

usto

m c

ycle

s

can b

e c

hosen.

Pro

ce

ss

Use

to

sel

ect

was

h w

ater

tem

per

atu

re

Pre

ss b

utt

on

to

sel

ect

01

(ho

t),0

2(w

arm

),03

(co

ld).

Tem

pe

ratu

re

Push this

bott

on to s

tart

. P

ush this

bott

on to s

top

during

the c

ycle

.

Sta

rt / P

au

se

D

ryin

g th

e tu

b

to

pre

ven

t m

ou

ld

gro

wth

.

Air

Dry

It is s

uit

ab

le f

or

wash

ing

s

tain

ed

la

un

dry

an

d s

oil

ed

c

oll

ar

an

d w

ris

t p

ort

ion

s o

f d

ress s

hir

ts .

So

ak

Indic

ate

s w

hic

h

C

ours

e has b

een

sele

cte

d.

Co

urs

e In

dic

ato

r

4.2 Wash cycle

Process

COURSE SOAKWATER

LEVEL

WASH

TIME

RINSE

CYCLE

SPIN

TIME

NORMAL *6~15 min.

*1~3 times

(Refill)

1~9 min.

*

MY FAVORITE *6~15 min.

*1~3 times

(Refill)

1~9 min.

*

SPEEDY * 6 or 9 min.2 times

(Refill)

3 min.

*

EXTRA RINSE *6~15 min.

*1~3 times

(Refill)

1~9 min.

*

COMFORTER 86L~99L6~15 min.

*1~3 times

(Refill)

1~9 min.

*

DELICATE 50L~62L 6 min. 1~3 times

(Refill)

1 min.

TUB HYGIENE 99L 15 min. 3 times 3 min.

* It is setting by laundry amount detects.

W

A

S

H

C

O

U

R

S

E

S

E

L

E

C

T

-5-

5. Test Mode

1.Set the power switch to "off".

2.Press and hold both the "Water lever" and "Wash" buttons with one hand.

3.Press the power switch to "on".

4.Release your fingers from the buttons and power switch which you pressed in steps (2) and (3) .

(Check A can be carried out in this state with your fingers released)

5.Within three seconds press the "Water lever " button to set the desirer check procedure.

(Carry out checks B, C, E, M, G and H)

Check Contents

When the end buzzer sounds three

Cycle end buzzer times, the lamps will simultaneously

0 A Timer indicator flash on and off in the remaining

Auto power off time display, and the power will auto-

matically be switched off immediately

after operation is finished.

Even if there is no water in the tub, the washing

Washing operation will continue for 6 minutes.

1 B operation Press the "wash" button once FV-1 operates,

and press twice to operate FV-2.

If the PCB fault occurred, an error indication

"H05" will display.

The spinning operation will continue for 7 minutes.

Spin operation **Check the lid & SF switch operation

2 C Lid/SF switch *While opening lid

1) "74L" lights up Lid switch working

2) "86L" lights up SF switch working

Operation conditionCheck

ProcedureLamp illumination condition

Number of timers

the "Water lever"

button is pressed

Check H Check G Check M Check E

Check A Check B Check C

(2) (3) (1)

-6-

Check Contents

Press the "WASH" button to adjust L0 (initial

mode) to L1 (1-rank higher water level).

Press "STAR/PAUSE" button to confirm.

In case to change PCB or remove the V-belt.

set the V-belt tension to initail mode for useing

below procedure.

M The initial display will be indicated "b0"

after that, press "START / PAUSE" button once,

it shall be listened click sound six times to

set properly.

"Digit lights" shall be indicated "E" initially,

Press "WASH" button to show the last error,

and press the wash botton again to return

to initial mode.

G If any error message occurred in the

past, "H" or "U" and some number shall

be indicated alternately.

If no error message occurred, the light

indicates "00".

"Digit lights" shall be indicated "C" initially,

Press "WASH" button to change "Indication

H of dight" of operation times.

Press once: Digit "ThousandHundred"

Press twice: Digit "TenOne"

Operation conditionCheck

ProcedureLamp illumination condition

Set to initial

mode for

tension of the

Belt

Number of times

the "Water lever"

button is pressed

3 E

4

Indicate the

error message

of the last time.

Indicate the

operation

times.

Adjust the

water amount

against laundry

amount

detection

5

6

-7-

6.Troubleshooting Guide 6.1 "U--" Error indication

*If there is an operation error, or if there is a problem with the washing machine, such as faulty draining,

spinning etc; operation will stop, the warning buzzer will sound, and an error indication will be displayed

Content Method to clear

Check if abnormalities listed below are seen in the

external water hose

*Is something wrong with the drain hose?

*Is the clogging with lint ?

Malfunction of *Is it crushed ? Restart by opening

drain *Is the tip soaked in water ? and close of the lid.

*Is a small pipe used ?

*Is a part of hose at a height of over 10cm in midway?

*Is the extension hose longer than 2 meter ?

*Is the drain hose lay down ?

*Is the lid is open ? Close the lid

*Check If condition of contact point of the lid switch.

*Is the washing machine in an unstead position, or is on

an inclined floor surface ? Open the lid and

*Is the adjustable knob loose ? redistribute the load.

*Is the laudry unevenly distributed in the tub ?

*Check if you have forgotten to connect the water hose

and to turn on the faucet.

*The water supply cut off?

Malfunction of *Check if the water supply and the water supply hose Opening and closing

water supply are frozen. the lid to return to

*Check if the connection of the water supply hose on initial stage of water

feed valve is clogged with dirt. supply.

*it is alarmed increase it is takes over 50 min. to reach

selected water level.

1.Remove the power cord

Child lock *Check if you condition of remaining water in the tub. plug and close the lid.

operated *No remaining water in the tub. 2.After plug in and press

-->Child lock fuction has operated. "POWER" switch to "ON"

position.

Indication Check point

U99

U11

U12

U13

U14

The lid is open

Unbalanced load

-8-

6.2 "H--" Error indication

If there is an operation error, or if there is a problem with the washing machine,

(1)All the switchs can not be operated.

(2)An error indication will be displayed.

Indication Method to clear

H01 The PS switch is abnormal. *Pull out the power plug .

H09 *Pull out the power plug .

H55*Malfuntion of over current of

inverter circuit.

*In case if overcurrent(above 10A)flow to the

inverter circuit,replace the PCB(Power side).

*Check if short circuit of the motor's coil,

replace the motor.

*Pull out the power plug .

H57 *Malfuntion of motor's current.*Check if movement of the motor,

and replace the motor.*Pull out the power plug .


H52 *Malfuntion of high voltage.

*In case the input voltage to the PCB has been

detected over AC 150V,check input voltage

by test meter.

*Indicate 5 sec and auto power off.


H53 *Malfuntion of low voltage.*In case the input voltage to the PCB has been

detected below AC 65V,check input voltage

by test meter.


*Check if you condition of the connectors.

*Replace the PS switch .

*Replace PCB board(Power side)

*Check if you condition of the power sw.


*Check if lead wire condition of P.C.

Boards between power and operation

side, and replace one of P.C. Board's.

H51 *Malfuntion of over load.

*Check if over load of laundry.

*Check if condition of connectors for motor

and rotary detector,necessary adjustment.

*Check if movement of the motor,replace it.

*Check if output voltage of the PCB(Power side)

,replace the PCB.

H25The Motorized Drain Valve

(For draining water) is abnormal.

*In case the motorized drain valve won't operate

within 20 sec, after drain mode has started.

*Check if condition of connectors for motorized

drain valve, replace the motorized drain valve

*Check output voltage of the PCB(Power side)

and replace the PCB.

H21


Check pointContent

The memory circuit of the I.C is

abnormal.*Replace PCB board(Power side)

Open circuit of P.C. Board's

communication line.

H04 The power sw circuit is abnormal.

H05


H07

*Malfuntion of over flow.

*Clean the diaphragm inside of the feed valve

or replace the the feed valve.

*Check output voltage of the PCB(Power side)

*Operate motorized drain valve and drain water



The rotary detector is abnormal.

*Check if condition of connectors for rotary

detector and leadwires

*Movement of the mechanism motor



-9-

7.Disassembly Instructions

7.1 Warning

Before attempting to servics or adjust any part of the machine, disconnect the electrical power suppy from the outlet.

7.2 Caution

Electronic components of the print circuit board is MOS TYPE FET. When replace and

trouble shooting of the print circuit board, make sure body is grounded before beginning

repair work. But, in case can not ground, touch to the plug and earth wire, and remove

the potential difference between the set and body of the worker completely.

7.3 The display PCB replacement

1. Remove 4 screws mounting the Body B,

then raise the Body B.

2. Remove 4 screws mounting the bottom

of Body B

3. Lift the Panel Face B upward to remove it.

4. Remove the connector and 10 screws

mounting the PC Board.

5. Remove the display PCB.

Display PCB

-10-

7.4 The POWER PCB, NOISE PCB, PS SWITCH, SF SWITCH and FEED VALVE replacement

1. Remove the window and 2 screws mounting the PANEL A, then remove the PANEL A.

2. The POWER PCB replacement.

a. Remove 1 screws mounting the PCB.

b. Pull the PCB out.

c. Remove the PCB Cover, then remove

the lead wire connector.

3. PS SWITCH replacement.

a. Remove lead wire connector.

b. Remove the SUB HOSE A.

4. SF SWITCH replacement.

a. Remove lead wire connector.

b. Remove 2 screws mounting the SF SWITCH.

SF Switch Sub Hose A Lead Wire Connector PS Switch Power supply PCB PCB Cover

Pull

-11-

5. FEED VALVE replacement.

a. Take DETERGENT CASE B out.

b. Remove LEAD WIRE CONNECTOR.

c. Remove 4 screws mounting the DETERGENT

CASE AU and FEED VALVE SUPPORT .

d. Pull DETERGENT CASE AU out.

e. Remove 2 screws mounting the FEED VALVE

(for clod water).

f. Move the spring by pliers than pull the FEED

VALVE (for hot water) out of the FEED HOSE.

6. The NOISE PCB replacement.

a. Remove 1 screws mounting the PCB.

b. Pull the PCB out.

c. Remove the PCB Cover, then remove

the lead wire connector.

Feed

Lead Wire

PULL

NOISE PCB PCB Cover

PULL OUT

PULL OUT

-12-

7.5 The MECHANISM U replacement

1. Remove 4 screws mounting the Body B, then raise the Body B.

2. Remove 8 screws mounting the OUTER TUB COVER.

3. Remove the special screw mounting the PULSATOR.

Do not remove the special screw from PULSATOR completely then hold the screw head to pull the PULSATOR upward to remove.

4. Remove the SHAFT BUSHINGD SHAFT FLANGE NUT and D FLANGE WASHER B, then pull the TUB upward to remove.

5. Turn the machine upside down.

6. Remove 4 screws(M8) mounting

the SPINNER PLATE B.

7. Remove 4 screws (M13)mounting

the MECHANISM U.

SHAFT BUSHING

D SHAFT FLANGE NUT

D FLANGE WASHER B

SPINNER PLATE B

MECHANISM U

-13-

7.6 The MOTOR replacement

1. Lay down the washing machine on it right side.

2. Remove both lead wire connectors from the MOTOR and the ROTARY SENSOR.

3. Loosen four bolts (M13) mounting the motor by using HW-18, and remove V-belt.

4. Remove four bolt mounting the MOTOR, and remove the motor.

Note: After replace the motor, adjust tension of the V-belt properly.

And then, set micro-processor to initial mode of V-belt tension by operating

Test-No water / Check procedure-E.

7.7 MOTORIZED DRAIN VALVE replacement

1. Lay down the washing machine on it left side.

2. Remove connector from the MOTORIZED

DRAIN VALVE.

3. Remove three screws mounting the

MOTORIZED DRAIN VALVE.

4. Remove slider portion of the MOTORIZED

DRAIN VALVE from the COCK ROD A.

7.8 PUMP replacement

1. Lay down the washing machine on it left side.

2. Loosen clamp and remove two hoses from the PUMP CASING.

3. Remove three screws mounting the PUMP BRACKET.

Connector of

Connector of rotary

Motor

V-belt

Checking tension of the V-belt

Motorized drain valve

Hose

Hose clamp

Pump casing

Cock rod A

Hose

-14-

8. Wiring Diagram

-15-

9. Parts Location & Replacement Parts List 9.1 Small standardized metal parts

Ref

No.Part Name Part No. Q'ty Remarks

1 BIND TAPPING SCREW XTB3+10BFJ 10 AXW24S+AXW145

2 BIND TAPPING SCREW X-T0405 4 AXW145+AXW102

3 BIND TAPPING SCREW XTB4+12CFJ 2 AXW1661+AXW102

4 BIND TAPPING SCREW XTB4+12CFJ 1 AXW24C+AXW102

5 BIND TAPPING SCREW XTB4+14CFJ 2 AXW2921+AXW20T

6 BIND TAPPING SCREW XTB4+12CFJ 2 AXW20T+AXW102

7 SPECIAL TAPPING SCREW X-T0405 2 AXW102+AXW1A

8 SPECIAL TAPPING SCREW X-T0405 2 AXW102+AXW1A+AXW0130

9 BIND TAPPING SCREW XTB4+12CFJ 1 AXW24V+AXW102

10 TRUSS TAPPING SCREW XTT4+14AFJ 1 AXW337+AXW301

11 SPECIAL TAPPING SCREW XTT4+14ABN 1 AXW2D+AXW301

12 TRUSS TAPPING SCREW XTT4+14AFJ 8 AXW301+AXW1A

13 SPECIAL SCREW C4585-480JB 5 AXW156+AXW1A

14 SPECIAL TAPPING SCREW XTWAXW511 2 AXW9D+AXW1201

15 SPECIAL TAPPING SCREW XTWAXW511 4 AXW1202+AXW1201

16 SPECIAL TAPPING SCREW XTWAXW6502J 8 AXW1202+AXW1201

17 TRUSS TAPPING SCREW XST4+8FY 1 AXW3F+AXW1202

18 SPECIAL TAPPING SCREW XTWAXW6506J 6 AXW3482+AXW1201

19 SPECIAL BOLT AXWX-V0825AJ 4 AXW20A+AXW1202

20 HEXAGON SPECIAL BOLT XVG7A22GXJ 1 AXW410+AXW401

21 HEXAGON NUT XNG7BSFJ 1 AXW410+AXW401

22 SPECIAL BOLT AXWX-V0640AJ 4 AXW401+AXW1202

23 SPECIAL BOLT AXWX-V0825AJ 2 AXW1231+AXW1202

24 SPECIAL BOLT AXWX-V0624J 4 AXW3232+AXW1202

25 TRUSS TAPPING SCREW X-T0407 4 AXW12T+AXW201

26 TRUSS TAPPING SCREW X-T0407 4 AXW12U+AXW201

27 SPECIAL TAPPING SCREW XTWAXW520 8 AXW35A+AXW201

28 SPECIAL TAPPING SCREW XTWAXW507 12 AXW1504+AXW201

29 SPRING WASHER XWA5BFJ 2 AXW5D+AXW20A

30 SPECIAL SCREW XSSAXW676E 1 AXW5D+AXW20A

31 TRUSS TAPPING SCREW XTT4+18ABN 8 AXW3224+AXW1201

-16-

9.2.1 Location of Parts-A

A31

A2

A3

A4

A25

A5

A1

A28

A17

A26

A10

A9

4

5

7

3

A11

A12

A24

A27

A29

A30

A33

1

A32

A7 A8

A6

A34

8

A31

A15

A13

A14

A16

2

9

A35

6

A18

A19

A20

A21

A22

A23

-17-

9.2.2 Replacement parts list-A

Ref

No.Part Name Part No. Q'ty FS14G2 FS16G2

A1 BODY B W0102-F6G50SW 1 X

BODY B(P) W0102-F6G50P 1 X

A2 PANEL FACE A W0145-B5S51SW 1 X

W0145-B5T00P 1 X

A3 PANEL FACE B W0146-F4G00 1 X

W0146-F6G00 1 X

A4 CONTROLLER U W024S-F4G00 1 X

W024S-F6G00 1 X

A5 LEAD WIRE U W014A-F6G00 1

A6 LEVEL W0353-15R00 1

A7 PS SWITCH W024T-03800 1

A8 SF SWITCH W1661-23210 1

A9 CONTROLLER U W024C-F4G00 1 X

W024C-F6G00 1 X

A10 CONTROLLER CASE COVER W0486-B5S01 1

A11 FIREPROOFING BRACKET A W1349-B5S00 1

A12 FIREPROOFING BRACKET B W1350-B5S00 1

A13 CONTROLLER CU W024V-F6G00 1

A14 CASE COVER-NOISE W2427-B5S00 1

A15 FIREPROOFING BRACKET A W1352-B5S00 1

A16 FIREPROOFING BRACKET B W1353-B5S00 1

A17 DETERGENT CASE AU W20T-F6G00 1

A18 JOINT PACKING W1292-6H000 2

A19 FEED VALVE W2921-16801 1

A20 FEED VALVE W2921-11901 1

A21 FEED VALVE SUPPORT W0195-F6G00 1

A22 FEED HOSE W1260-F6G00 1

A23 HOSE CLAMP W0245-F6G00 2

A24 DETERGENT CASE B W2151-B5S01SW 1 X

W2151-B5S01HA 1 X

A25 DETERGENT CASE COVER W2192-B5S00MG 1

A26 LID SPRING W1116-B5S00 1

A27 SF LEVER W1192-B5T00 1

A28 PANEL AU W0130X-F4G00 1 X

W0130X-F6G00 1 X

A29 POWER CORD U W004A-F6G00 1

A30 FUSE U W014C-13X00 1

A31 LID UX W001G-F4G00 1 X

W001G-F6G00 1 X

A32 LID HINGE SHAFT W0193-105B2 2

A33 BODY B COVER W0163-1DH00SW 2 X

W0163-1DH00MH 2 X

A34 SF CUSHION W9047-13G00 1

A35 INDUCTOR W034L-B5S30 1

-18-

9.3.1 Location of Parts-B

B24

B1

B2

B12

B13

B14

B9

B8

B11

5

9

5

B2

B3

B4

B10

B9

B6

B5

B7

B10

B13

B11

B11

5

B15

B20

B23

B21

B16

B19

B18

B26

B7

7

23

6

23

B20

B25

B27

B22

-19-

9.3.2 Replacement parts list-B

Model No.

FS14G2 FS16G2

B1 BODY AU W001A-F6G00SW 1 X

W001A-F6G00MH 1 X

B2 GRIP W0110-11A01SW 2 X

W0110-11A01HA 2 X

B3 BODY SPONGE A W3254-B6S00 1

B4 BODY SPONGE W3254-14T00 3

B5 DRAIN HOSE HOLDER W0179-B4G00SW 1

B6 DRAIN HOSE W0179-B4G00SW 1

B7 HOSE CLAMP W0245U-B4GB1 2

B8 BASE AU W003B-B4G00BK 1

B9 HOSE HOLE COVER W0128-11A00N1 2

B10 LEG BRACKET W0341-90R00 3

B11 LEG COVERING W0339-90R00C 3

B12 ADJUSTABLE LEG FIXER W0337-15HA0 1

B13 ADJUSTABLE KNOB W0343-15H00BK 1

B14 ADJUSTABLE LEG SHAFT U W0335U-15HA0 1

B15 PUMP BPX1-9L 1

B16 PUMP CASING W0801-B4G00 1

B17 SPONGE W3254-B4G00 1

B18 DRAIN FILTER W2203-B4G00 1

B19 DRAIN FILTER PACKING W3427-B4G00 1

B20 PUMP BRACKET W0827-B4G00 1

B21 WATERPROOFING COVER W1238-B4G00 1

B22 PUMP WASHER A W0833-B4GA0 3

B23 PUMP WASHER B W0833-B4GB0 2

B24 REAR PANEL W0156-11A53 1

B25 EARTH U W003F-B2XV0 1

B26 PUMP WASHER C W0834-B4G00 1

B27 PACKING W0224-16H50 2

Ref.

NoDescription Part No. Q'ty

-20-

9.4.1 Location of Parts-C

C30

C29

C4

C8

C15

C13

C27 C26

C25

C5

C10 C17

C12

C18

C2

C32

C31

C28

C20 C1

6

19

2

11

12

16

17

7

8

C9

C19

1 13

10

1

C34

C3,C35

C1

C1 C1

C6

C7

C11

C16

C14

1

21 2

C7

To B19

C21

C23

C22

C24 C33

C33

-21-

9.4.2 Replacement parts list-C

Model No.

FS14G2 FS16G2

C1 SUSPENSION AU W034I-V16N 4

C2 OUTER TUB A W1201-11A05 1

C3 OF COVER W0297-B4G01 1

C4 OUTER TUB B W1202-15HA5 1

C5 SLIDER U W006T-B4G00 1

C6 FLEXIBLE HOSE A W0247-B4G00 1

C7 HOSE CLAMP W0245-B4GA0 2

C8 EARTH WIRE U W003F-B2XV0 1

C9 GEAR MOTOR SUPPORT W3483-15H01 2

C10 MOTORIZED DRAIN VALVE W3482-02502 1

C11 LEAD WIRE U W014B-B4G00 1 X

W014B-F6G00 1 X

C12 MECHANISM CASE U W020A-16T00 1

C13 V BELT W0412-2105E 1

C14 MOTOR PWM1303S1/PSN 1 X

PWM1803S/PSN 1 X

C15 MOTOR PULLEY W0410-B5S00 1

C16 MOTOR WASHER W0420-B5S00 2

C17 BALANCER WEIGHT W1231-90R20 1

C18 SPINNER PLATE B W3232-11AA0 1

C19 FIREPROOFING COVER W1348-15N00 1

C20 TUB AU W0201-B4X200 1 X

W0201-B6X200 1 X

C21 TUB BU W012T-15N01EA2 2 X

W012T-16N01EA2 2 X

C22 TUB C W012U-B5T00 2 X

W012U-B6T00 2 X

C23 DETERGENT SUPPORT W1198-B5S00KG 1

C24 TUB C W012U-B4X20EA2 1 X

W012U-B6X20EA2 1 X

C25 D SHAFT FLANGE W1504-11A02C 1

C26 D FLANGE WASHER B W1519-80200 1

C27 D SHAFT FLANGE NUT W1517-90S00 1

C28 SHAFT BUSHING W0504-70700 1

C29 PULSATOR U W005D-15K00KG 1 X

W005D-16L00KG 1 X

C30 OUTER TUB COVER W3224-B6X20EA2 1

C31 SUB HOSE A W0239-B5S00 1

C32 SUB HOSE CLAMP W0264-105A1 1

C33 FILTER U W022A-95U02EA2 2

C34 SPONGE A W3254-20550 1

C35 PACKING W0224-B4G00 1

Ref.


-22-

9.5.2 Replacement parts list-D

Model No.

FS14G2 FS16G2

D1 CASE BU W090B-13X00 1

D2 PRESSURE HOSE U(1.0M-HOT) W012C-F6G00 1

D3 PRESSURE HOSE U(1.0M) W012C-5VV50 1

D4 FLEXIBLE HOSE B W002E-B4GN0 1

D5 HOSE CLAMP U W0245U-B4GB1 1

D6 OPERATION INSTRUCTUON W9901-F4G00 1 X

W9901-F6G00 1 X

D7 PE SHEET W9060-13X00 1

D8 PE COVER W9060-85420 1

D9 TUB SUPPORT W9085-B4X200 1 X

W9085-B6X201 1 X

D11 TUB SUPPORT PE COVER W9060-11A00 1

D12 UPPER CUSHION W9004-B4X2 1

D13 CASE A W9001-F4G00P 1 X

W9001-F6G00P 1 X

Remark

9.5.1 Location of Parts-D

Ref.


D1

D8

D2 D6

D9

D11

D12

D4

D7

D10 D5

D3

-23-

Documents

NA-FS16G2-14G2 Panasonic Washing Machine Service Manual