-
NCSExpert Modify PSW_ V1.0by Mark
UPDATE: 24th June 2009 to Version 1.0 - What you need. NCSExpert
3.10.0 Fisters Profile Im not providing any files due to legality
issues, the files are out there you can find them. In this tutorial
I am going to disable the Legal Disclaimer that pops up on the
Idrive unit of an E90.This excercise is purely for example and can
be adapter for different modules and different changes.
Once NCS is open Choose File from the top menu
Select Load Profil
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
1 von 10 2010-10-12 01:11
-
Choose Fister profile if you have obtained it or new_expertmode
/ car/key memory.
Then Press F1 or choose VIN/ZCS/FA
Now press F3 or choose ZCS/FA f. Ecu
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
2 von 10 2010-10-12 01:11
-
Select the model car, In this case E89 which is for the E90
Chose the Module in which to read the ZCS/FA, In this case we
chose CAS.
Upon seeing the above screen with the FG and FA Values displayed
simply hit F6 or Back.
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
3 von 10 2010-10-12 01:11
-
You will now get a list of installed modules that were
identified when communication with the chosen module as
before.Choose Process ECU to work with a single module.
Select the Module/ECU you would like to work with, In this case
the CAPPL. (CCC Unit)
Press OK on the following screen.
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
4 von 10 2010-10-12 01:11
-
Now you can choose READ ECU to perform a read out of the
module.
You will get a NETTODAT.TRC file popup simply close it.
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
5 von 10 2010-10-12 01:11
-
Navigate to the Work folder which resides in your NCSEXPER
directory. You will locate a file FSW_PSW.TRC
This file was created when READ ECU was performed and contains
the coding values for that module.Rememeber this file is
overwritten each time a readout of a module is performed. It would
be advised to make a backup
of this file in the event you need to restore coding
settings.
Once you have made a backup, Right click and rename the file to
FSW_PSW.MAN
Yes to make the change.
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
6 von 10 2010-10-12 01:11
-
Now right click and choose Open With...
Select Notepad and tick Always use the selected program to open
this kind of file. Then Press OK.
Now we can make changes to the coding file. In this case we are
changing LEGAL_DISCL
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
7 von 10 2010-10-12 01:11
-
As you can see from the screen above we have changed this to
nicht_aktiv which will now disable the Idrive warning.
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
8 von 10 2010-10-12 01:11
-
Choose file and click save.
Now switch back to NCSExper and choose file and click Load
Profil
Choose the Manual PSW_FSW and hit ok.
Now press Process ECU so we can tell NCSExper what module we
would like to code to.
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
9 von 10 2010-10-12 01:11
-
Choose the CAPPL modules and press ok.
Press Ok.
Now we are ready to code the PSW_FSW.man to our CAPPL (CCC)
unit. Make sure the JOBNAME is set to SG_CODIEREN.If it is not
simply choose Job and choose SG_CODIEREN. Make sure the get coded:
is CAPPL (Or the unit you will be working with)
Hit Execute Job to perform coding.
Underneath CAPPL a status will appear intially saying CODING
ACTIV and then CODING ENDED.
Once this is disabled you may power off the car wait 10 seconds
and repower up to identify whether your coding changes have
taken.
NCSExpert Tutorial http://ausbmw.com/tutorials/NCSTutorial/
10 von 10 2010-10-12 01:11
