ND 7000 Demo - heidenhain.fr...To enter data, you can use the screen keyboard of the touchscreen or a connected keyboard. 3.2.2 Gestures and mouse actions To activate, switch or move

ND 7000 DemoUser’s ManualDrilling with Radial DrillingMachines

Digital Readout

English (en)01/2020

Contents

Contents

1 Fundamentals....................................................................................................................................7

2 Software installation......................................................................................................................11

3 Basic operation............................................................................................................................... 17

4 Software configuration.................................................................................................................. 43

5 Quick Start...................................................................................................................................... 49

6 ScreenshotClient.............................................................................................................................63

7 Index.................................................................................................................................................69

8 List of figures..................................................................................................................................71

2 HEIDENHAIN | ND 7000 Demo | User’s Manual Drilling with radial drilling machines | 01/2020

Contents

1 Fundamentals....................................................................................................................................7

1.1 Overview................................................................................................................................................. 8

1.2 Information on the product.................................................................................................................. 8

1.2.1 Demo software for demonstration of the device functions...................................................... 81.2.2 Demo software features............................................................................................................8

1.3 Intended use........................................................................................................................................... 8

1.4 Improper use.......................................................................................................................................... 8

1.5 Notes on reading the documentation................................................................................................. 8

1.6 Symbols and fonts used for marking text.......................................................................................... 9

2 Software installation......................................................................................................................11

2.1 Overview............................................................................................................................................... 12

2.2 Downloading the installation file.......................................................................................................12

2.3 System requirements...........................................................................................................................12

2.4 Installing ND 7000 Demo in Microsoft Windows............................................................................. 13

2.5 Uninstalling ND 7000 Demo............................................................................................................... 15

HEIDENHAIN | ND 7000 Demo | User’s Manual Drilling with radial drilling machines | 01/2020 3

Contents

3 Basic operation............................................................................................................................... 17

3.1 Overview............................................................................................................................................... 18

3.2 Using the touchscreen and input devices.........................................................................................18

3.2.1 Touchscreen and input devices............................................................................................... 183.2.2 Gestures and mouse actions...................................................................................................18

3.3 General operating elements and functions.......................................................................................20

3.4 ND 7000 Demo – startup and shut-down..........................................................................................22

3.4.1 Starting the ND 7000 Demo................................................................................................... 223.4.2 Shutting down the ND 7000 Demo........................................................................................ 23

3.5 User login and logout......................................................................................................................... 23

3.5.1 User login.................................................................................................................................233.5.2 User logout.............................................................................................................................. 23

3.6 Setting the language........................................................................................................................... 24

3.7 User interface....................................................................................................................................... 24

3.7.1 User interface after Startup..................................................................................................... 243.7.2 Main menu of the user interface............................................................................................ 253.7.3 Manual operation menu...........................................................................................................273.7.4 MDI menu................................................................................................................................283.7.5 Program run menu (software option)...................................................................................... 303.7.6 Programming menu (software option).....................................................................................313.7.7 File management menu...........................................................................................................333.7.8 User login menu...................................................................................................................... 343.7.9 Settings menu..........................................................................................................................353.7.10 Switch-off menu.......................................................................................................................36

3.8 Position display.................................................................................................................................... 36

3.8.1 Operating elements of the position display............................................................................ 363.8.2 Position display functions........................................................................................................ 37

3.9 Status bar............................................................................................................................................. 38

3.9.1 Operating elements of the status bar..................................................................................... 383.9.2 Additional functions in Manual operation mode......................................................................40

3.10 OEM bar................................................................................................................................................ 40

3.10.1 Operating elements of the OEM bar...................................................................................... 41


Contents

4 Software configuration.................................................................................................................. 43

4.1 Overview............................................................................................................................................... 44

4.2 Setting the language........................................................................................................................... 44

4.3 Activating software options................................................................................................................45

4.4 Selecting the product version (optional)...........................................................................................45

4.5 Selecting the Application....................................................................................................................46

4.6 Copying the configuration file............................................................................................................46

4.7 Uploading the configuration data......................................................................................................47

5 Quick Start...................................................................................................................................... 49

5.1 Overview............................................................................................................................................... 50

5.2 Logging in for Quick Start.................................................................................................................. 51

5.3 Requirements........................................................................................................................................52

5.4 Determining the preset (manual operation)..................................................................................... 53

5.5 Machining a through hole (manual operation).................................................................................54

5.5.1 Predrilling the through hole..................................................................................................... 555.5.2 Boring the through hole...........................................................................................................55

5.6 Machining a fit (MDI mode of operation)......................................................................................... 56

5.6.1 Defining the fit.........................................................................................................................565.6.2 Reaming the fit........................................................................................................................ 57

5.7 Drilling a bolt hole circle (MDI mode)............................................................................................... 57

5.7.1 Defining the bolt hole circle.................................................................................................... 585.7.2 Drilling the bolt hole circle.......................................................................................................58

5.8 Programming a row of holes (programming)...................................................................................59

5.8.1 Creating the program header.................................................................................................. 595.8.2 Programming the tool..............................................................................................................605.8.3 Programming the row of holes............................................................................................... 605.8.4 Simulating program run........................................................................................................... 61

5.9 Machining a row of holes (program run).......................................................................................... 61

5.9.1 Opening the program.............................................................................................................. 625.9.2 Running a program.................................................................................................................. 62


Contents

6 ScreenshotClient.............................................................................................................................63

6.1 Overview............................................................................................................................................... 64

6.2 Information about ScreenshotClient..................................................................................................64

6.3 Starting ScreenshotClient................................................................................................................... 65

6.4 Connecting ScreenshotClient with the demo software...................................................................65

6.5 Connecting ScreenshotClient with the unit......................................................................................66

6.6 Configuring ScreenshotClient for taking screenshots..................................................................... 66

6.6.1 Configuring the storage location and file name for screenshots.............................................666.6.2 Configuring the user interface language of screenshots.........................................................67

6.7 Creating screenshots........................................................................................................................... 68

6.8 Exiting ScreenshotClient..................................................................................................................... 68

7 Index.................................................................................................................................................69

8 List of figures..................................................................................................................................71


1Fundamentals

Fundamentals | Overview 1

1.1 OverviewThis chapter contains information about the product and this manual.

1.2 Information on the product

1.2.1 Demo software for demonstration of the device functionsND 7000 Demo is a software application you can install on a computerindependently of the device. ND 7000 Demo helps you to become familiar with,try out or present the functions of the device.

1.2.2 Demo software featuresBecause of the missing hardware environment the range of features of the demosoftware does not correspond to the complete functional range of the device.However, you can use the descriptions to familiarize yourself with the mostimportant functions and the user interface.

1.3 Intended useThe products of the ND 7000 series are advanced digital readouts for use onmanually operated machine tools. In combination with linear and angle encoders,digital readouts of this series return the position of the tool in more than one axisand provide further functions for operating the machine tool.ND 7000 Demo is a software product for demonstration of the basic features ofthe ND 7000 series products. ND 7000 Demo may be used only for presentation,training or testing purposes.

1.4 Improper useND 7000 Demo is not intended for any use other than the intended use. Any usefor other purposes is prohibited, specifically:

For productive purposes in production systemsAs part of production systems

1.5 Notes on reading the documentation

Have you found any errors or would you like to suggest changes?

We continuously strive to improve our documentation for you. Please help us bysending your suggestions to the following e-mail address:[email protected]


mailto:[email protected]

Fundamentals | Symbols and fonts used for marking text

1.6 Symbols and fonts used for marking textIn these instructions the following symbols and fonts are used for marking text:

Depiction Meaning

...

...Identifies an action and the result of this actionExample:

Tap OKThe message is closed

...

...Identifies an item of a listExample:

TTL interfaceEnDat interface...

Bold Identifies menus, displays and buttonsExample:

Tap Shut downThe operating system shuts downTurn the power switch off

1


2Software

installation

Software installation | Overview 2

2.1 OverviewThis chapter provides all of the information needed for downloading and properlyinstalling ND 7000 Demo on a computer.

2.2 Downloading the installation fileBefore you can install the demo software on a computer, you need to download aninstallation file from the HEIDENHAIN Portal.

To download the installation file from the HEIDENHAIN Portal, youneed access rights to the Software portal folder in the directory of theappropriate product.If you do not have access rights to the Portal's Software folder, you canrequest the access rights from your HEIDENHAIN contact person.

Download the latest version of ND 7000 Demo here: www.heidenhain.de

Select the download folder of your browserUnpack the downloaded file with the extension .zip into a temporary storagefolderThe following files will be unpacked into the temporary storage folder:

Installation file with the extension .exe

File DemoBackup.mcc

2.3 System requirements

If you want to install ND 7000 Demo on a computer, the computer system mustmeet the following requirements:

Microsoft Windows 7 or higherScreen resolution of at least 1280 × 800 recommended


http://www.heidenhain.de

Software installation | Installing ND 7000 Demo in Microsoft Windows

2.4 Installing ND 7000 Demo in Microsoft WindowsSelect the temporary storage folder into which you unpacked the downloadedfile with the .zip extensionFurther information: "Downloading the installation file", Page 12Run the installation file with the extension .exe

The installation wizard is opened:

Figure 1: Installation wizard

Click Next

In the License Agreement installation step, accept the terms of the licenseClick Next

In the Select Destination Location installation step, the installationwizard suggests a storage location. We recommend retaining thesuggested storage location.

In the Select Destination Location installation step, select the storagelocation to which you want to save ND 7000 Demo Click Next

In the Select Components installation step, the ScreenshotClientprogram is also installed by default. ScreenshotClient enables you totake screenshots of the active screen.If you want to install ScreenshotClient

In the Select Components installation step, leave the defaultsettings unchanged

Further information: "ScreenshotClient", Page 63

In the Select Components installation step:Select the type of installationActivate or deactivate the option Screenshot Utility

2


Software installation | Installing ND 7000 Demo in Microsoft Windows 2

Figure 2: Installation wizard with activated options Demo software and ScreenshotUtility

Click Next

In the Select Start Menu Folder installation step, select the storage location atwhich you want to create the start menu folderClick Next

In the Select Additional Tasks installation step, select or deselect Desktopicon

Click Next

Click Install

Installation starts—the status of installation is shown in the progress barAfter installation has been completed successfully, use Finish to close theinstallation wizardThe program has been successfully installed on your computer


Software installation | Uninstalling ND 7000 Demo

2.5 Uninstalling ND 7000 DemoSelect the following in succession in Microsoft Windows:

StartAll programsHEIDENHAIN

ND 7000 Demo

Click UninstallThe uninstallation wizard opensTo confirm uninstalling, click YesUnistallation starts, and the progress bar indicates the status of the unistallationprocessAfter uninstallation has been completed successfully, close the uninstallationwizard with OKThe program has been successfully removed from your computer

2


3Basic operation

Basic operation | Overview 3

3.1 OverviewThis chapter describes the user interface, operating elements, and basic functions of ND 7000 Demo.

3.2 Using the touchscreen and input devices

3.2.1 Touchscreen and input devicesThe operating elements on the user interface from ND 7000 Demo are operatedvia a touchscreen or a connected mouse.To enter data, you can use the screen keyboard of the touchscreen or a connectedkeyboard.

3.2.2 Gestures and mouse actionsTo activate, switch or move the operating elements of the user interface, you canuse ND 7000 Demo's touchscreen or a mouse. Gestures are used to operate thetouchscreen and the mouse.

The gestures for operating the touchscreen may differ from thegestures for operating the mouse.If the gestures for operating the touchscreen differ from those foroperating the mouse, then these instructions describe both operatingoptions as alternative actions.The alternative actions for operating the touchscreen or the mouse areidentified by the following symbols:

Operation using the touchscreen

Operation using the mouse

The following overview describes the different gestures for operating thetouchscreen or the mouse:

Tapping

Means touching the screen briefly with your fingertip

Means pressing the left mouse button once


Basic operation | Using the touchscreen and input devices

The actions initiated by tapping include

Selection of menus, features or parametersEntering characters with the screen keyboardClosing dialogs

Holding (long press)

Means touching the screen and holding your finger(s) on it for afew seconds

Means pressing the left mouse button once and holding itdown

The actions initiated by holding are

Quickly changing the values in input fields with plus andminus buttons

Dragging

Is a combination of long press and then swipe, moving a fingerover the touchscreen when at least the starting point of motionis defined

Means pressing the left mouse button once and holding itdown while moving the mouse; at least the starting point of themotion is defined

The actions initiated by dragging include

Scrolling through lists and texts

3


Basic operation | General operating elements and functions 3

3.3 General operating elements and functionsThe operating elements described below are available for configuration andoperating the product via the touchscreen or input devices.

Screen keyboard

With the screen keyboard, you can enter text into the input fields of the userinterface. Depending on the input field, a numeric or alphanumeric screenkeyboard is shown.

To enter values, tap an input fieldThe input field is highlightedThe screen keyboard is displayedEnter text or numbersThe correctness of the entry in the input field is shown with a green checkmarkIf the entry is incomplete or incorrect, a red exclamation mark is displayed. Inthis case, the entry cannot be completedTo apply the values, confirm the entry with RETThe values are displayedThe screen keyboard disappears

Input fields with plus and minus buttons

To adjust a numerical value, use the + (plus) and – (minus) buttons to the left andright of the numerical value.

Tap + or – until the desired value is displayedLong-press + or – to scroll through the values morequicklyThe selected value is displayed

Toggle switch

Use the toggle switch to switch between functions.

Tap the desired functionThe active function is shown in greenThe inactive function is shown in light gray

Slide switch

With the sliding switch, you can activate or deactivate a function.

Drag the slider to the desired positionor

Tap the sliderThe function is activated or deactivated

Drop-down list

Buttons that open drop-down lists are indicated by a triangle pointing down.

Tap the buttonThe drop-down list opensThe active entry is highlighted in greenTap the desired entryThe selected entry is applied


Basic operation | General operating elements and functions

Undo

With this button, you can undo the last action.Processes that have already been concluded cannot be undone.

Tap UndoThe last action is undone

Add

To add a feature, tap AddThe new feature is added

Close

Tap Close to close a dialog

Confirm

Tap Confirm to conclude an activity

Back

Tap Back to return to the higher level in the menustructure

3


Basic operation | ND 7000 Demo – startup and shut-down 3

3.4 ND 7000 Demo – startup and shut-down

3.4.1 Starting the ND 7000 Demo

Before using ND 7000 Demo, you need to perform the steps forconfiguring the software.

NDTap ND 7000 Demo on the Microsoft Windows desktop

orOpen the following in sequence in Microsoft Windows:


ND 7000 Demo

Two executable files with different modes ofappearance are available:

ND 7000 Demo: starts within a MicrosoftWindows windowND 7000 Demo (full screen): starts in full-screen mode

NDTap ND 7000 Demo or ND 7000 Demo (full screen)

ND 7000 Demo starts an output window in the background.The output window is not relevant for operation and is closedagain when the ND 7000 Demo is shut downND 7000 Demo starts the user interface with the User loginmenu

Figure 3: User login menu


Basic operation | ND 7000 Demo – startup and shut-down

3.4.2 Shutting down the ND 7000 Demo

Tap Switch off in the main menu

Tap Shut downND 7000 Demo is shut down

To shut down ND 7000 Demo in the Microsoft Windows window, alsouse the Switch-off menu.If you use Close to close the Microsoft Windows window, all settingswill be lost.

3.5 User login and logoutIn the User login menu, you can log in and out of the product as a user.Only one user can be logged in to the product at a time. The logged-in user isdisplayed. Before a new user can log in, the logged-in user has to log out.

The product provides various authorization levels that grant the user fullor restricted access to management and operation functionality.

3.5.1 User login

Tap User login in the main menuIn the drop-down list, select the OEM userTap the Password input fieldEnter the "oem" password of the OEM userConfirm entry with RETTap Log inThe user is logged in and the is displayed

3.5.2 User logout

Tap User login in the main menu

Tap Log outThe user is logged outAll functions of the main menu are inactive, except for SwitchoffThe product can only be used again after a user has logged in

3


Basic operation | Setting the language 3

3.6 Setting the languageThe user interface language is English. You can change to another language, ifdesired.

Tap Settings in the main menu

Tap UserThe logged-in user is indicated by a check markSelect the logged-in userThe language selected for the user is indicated by a nationalflag in the Language drop-down listSelect the flag for the desired language from the Languagedrop-down listThe user interface is displayed in the selected language

3.7 User interface

The unit is available in different versions, which are variously equipped.The user interface and available functions may vary depending on theversion.

3.7.1 User interface after Startup

User interface after startup

If automatic user login is activated, and the last user who logged in was of theOperator type, then the product displays the Manual operation menu afterstarting up.

If automatic user login is not activated, then the product opens the User loginmenu.Further information: "User login menu", Page 34


Basic operation | User interface

3.7.2 Main menu of the user interface

User interface (in Manual operation mode)

1

2

1 Message display area, displays the time and the number of unclosed messages2 Main menu with operating elements

Main menu operating elements

Control Function

3MessageDisplay of an overview of all messages as well as thenumber of messages that have not been closed

Manual operationManual positioning of machine axesFurther information: "Manual operation menu",Page 27

MDI modeDirect input of the desired axis movements (Manual DataInput); the distance to go is calculated and displayedFurther information: "MDI menu", Page 28

Program run (software option)Execution of a previously created program with user inter-faceFurther information: "Program run menu (softwareoption)", Page 30

Programming (software option)Creation and management of individual programsFurther information: "Programming menu (softwareoption)", Page 31

File managementManagement of the files that are available on the productFurther information: "File management menu",Page 33

3


Basic operation | User interface 3

Control Function

User loginLogin and logout of the userFurther information: "User login menu", Page 34

If a user with additional permissions ( Setupor OEM user type) is logged in, then the gearsymbols appears.

SettingsSettings of the product, such as setting up users, configur-ing sensors, or updating the firmwareFurther information: "Settings menu ", Page 35

Switch-offShutdown of the operating system or activation of power-saving modeFurther information: "Switch-off menu", Page 36

Selecting grouped operating elements

When Software-Option ND 7000 PGM is activated, the following operatingelements are grouped in the main menu:

MDI mode

Program run

Programming

You can identify grouped operating elements by an arrow.

To select an operating element from the group, tap theoperating element with the arrow (e.g., tap MDI mode)The operating element is shown as activeTap the operating element againThe group opensSelect the desired operating elementThe selected operating element is shown as active



3.7.3 Manual operation menu

Activation

Tap Manual operation in the main menuThe user interface for manual operation is displayed

1

3

2

45

1 Axis key2 Position display3 Status bar4 Spindle speed (machine tool)5 Reference

In the Manual operation menu, the workspace shows the position valuesmeasured at the machine axes.The status bar provides auxiliary functions.

3



3.7.4 MDI menu

Activation

Tap MDI in the main menu

The operating element can belong to a group (basedon the configuration).Further information: "Selecting grouped operatingelements", Page 26

The user interface for MDI mode is displayed

1 32

4

1 Axis key2 Actual position3 Distance-to-go4 Status bar



MDI block dialog box



Tap Create on the status barThe user interface for MDI mode is displayed

1 2 3

4

5

Figure 4: MDI block dialog box

1 View bar2 Block parameters3 MDI block4 Status bar5 Block tools

The MDI (Manual Data Input) menu enables you to enter the desired axismovements directly. You specify the distance to the target point, and the distanceto go is then calculated and displayed.The status bar provides additional measured values and functions.

3



3.7.5 Program run menu (software option)

Calling up

Tap Program run in the main menu

The operating element belongs to a group.Further information: "Selecting grouped operatingelements", Page 26

The user interface for Program Run is displayed

1

2

5 34

Figure 5: Program run menu

1 View bar2 Status bar3 Program control4 Spindle speed (machine tool)5 Program management

The Program run menu makes it possible to execute a program that haspreviously been created in the Programming operating mode. During execution, awizard will guide you through the individual program steps.In the Program run menu, you can display a simulation window that visualizes theselected block.The status bar provides additional measured values and functions.



3.7.6 Programming menu (software option)

Calling up

Tap Programming in the main menu


The user interface for programming is displayed

The status bar and the optional OEM bar are not available in theProgramming menu.

1 2

3

Figure 6: Programming menu

1 View bar2 Toolbar3 Program management

You can see a visualization of the selected block in the optional simulation window.

3



1

3

2

4

5

Figure 7: Programming menu with opened simulation window

1 View bar2 Simulation window (optional)3 Toolbar4 Program blocks5 Program management

In the Programming menu, you can create and manage programs. You defineindividual machining steps or machining patterns as blocks. A sequence of blocksthen forms a program.



3.7.7 File management menu

Calling up

Tap File management in the main menuThe file management user interface is displayed

Short description

1

2

Figure 8: File management menu

1 List of available storage locations2 List of folders in the selected storage location

The File management menu shows an overview of the files stored in theg133product’s memory.

3



3.7.8 User login menu

Calling up

Tap User login in the main menuThe user interface for user login and logout is displayed

Short description

1 2

Figure 9: User login menu

1 Display of the logged-in user2 User login

The User login menu shows the logged-in user in the column on the left. The loginof a new user is displayed in the right-hand column.To log in another user, the logged-in user must first log out.Further information: "User login and logout", Page 23



3.7.9 Settings menu

Calling up

Tap Settings in the main menuThe user interface for the product settings is displayed

Short description

1 2

Figure 10: Settings menu

1 List of setting options2 List of setting parameters

The Settings menu shows all of the options for configuring the product. With thesetting parameters, you can adapt the product to on-site requirements.

The product provides various authorization levels that grant the user fullor restricted access to management and operation functionality.

3



3.7.10 Switch-off menu

Activation

Tap Switch off in the main menuThe operating elements for shutting down the operatingsystem, for activating the energy-saving mode and foractivating the cleaning mode are displayed

Short description

The Switch off menu provides the following options:

Operatingelement

Function

Shut downShuts down ND 7000 Demo

Energy saving modeSwitches the screen off and puts the operating system intoenergy-saving mode

Cleaning modeSwitches the screen off; the operating system continuesunchanged

Further information: "ND 7000 Demo – startup and shut-down", Page 22

3.8 Position displayThe unit’s position display shows the axis positions and additional informationabout the configured axes (if applicable).

3.8.1 Operating elements of the position display

Symbol Meaning

XAxis keyAxis key functions:

Tapping the axis key: opens the input field for positionvalue (Manual operation) or dialog box MDI block (MDImode)Holding down the axis key: sets the current position aszero pointDragging the axis key to the right: opens menu iffunctions are available for the axis

R Reference mark search performed successfully

R Reference mark search not performed or no reference markdetected

1 Selected gear stage of the gear spindleFurther information: "Setting the gear stage for gearspindles", Page 38


Basic operation | Position display

Symbol Meaning

Spindle speed cannot be achieved with selected gear stageSelect a higher gear stage

Spindle speed cannot be achieved with selected gear stageSelect a lower gear stage

In MDI mode and Program Run , a scaling factor is appliedto the axis

3.8.2 Position display functions

Setting the spindle speed

The following information applies only to units with ID number1089179-xx.

You can control the spindle speed depending on the configuration of theconnected machine tool.

Tap or long-press + or – to set the spindle speed to thedesired value

orTap the Spindle speed input field, enter the value and tapRET to confirmThe product applies the entered spindle speed as thenominal value and controls the spindle of the machine toolaccordingly

3


Basic operation | Position display 3

Setting the gear stage for gear spindles

The following information applies only to units with ID number1089179-xx.

If your machine tool uses a gear spindle, then you can select the gear stage used.

The selection of the gear stages can also be controlled via an externalsignal.

SIn the working space, drag the S axis key to the right

Tap Gear stageThe Set gear stage dialog appearsTap the desired gear stageTap ConfirmThe selected gear stage is now adopted as the new valueDrag the S axis key to the left

1 The icon for the selected gear stage appears next to the Saxis key

If the desired spindle speed cannot be attained with the selected gearstage, then the gear stage icon will flash with an upward pointing arrow(higher gear stage) or with a downward pointing arrow (lower gearstage).

3.9 Status bar


In the status bar, the product shows the feed rate and traversing speed. Theoperating elements of the status bar also give you direct access to the preset tableand tool table, as well as to the stopwatch and calculator features.

3.9.1 Operating elements of the status barThe status bar provides the following operating elements:

Operatingelement

Function

Quick access menuSetting of the units for linear values and angular values,configuration of a scaling factor; tapping opens the quickaccess menu

Preset tableDisplay of the current preset; tapping opens the presettable


Basic operation | Status bar

Operatingelement

Function

Tool tableDisplay of the current tool; tapping opens the tool table

StopwatchTime display with Start / Stop function in h:mm:ss format

CalculatorCalculator with the most important mathematical functionsand speed calculator

Feed rateDisplay of the actual feed rate of the currently fastest axis

Auxiliary functionsAuxiliary functions in Manual operation mode, dependingon the configured application mode

MDI blockFor creating machining blocks in MDI mode

3


Basic operation | Status bar 3

3.9.2 Additional functions in Manual operation mode

To call the additional functions, tap Additional functions inthe status bar

The following operating elements are available:

Operatingelement

Function

Reference marksFor starting the reference mark search

ProbingFor probing the edge of a workpiece

ProbingFor finding the centerline of a workpiece

ProbingFor finding the center point of a circular feature (hole orcylinder)

ProbingDetermine the orientation and preset via edges (twoprobing operations on the first axis, one probing operationon the second axis)

ProbingDetermine the orientation via edges (two probingoperations)

ProbingDetermine the orientation via circle center points (threeprobing operations per hole with tool, four probingoperations with edge finder)

3.10 OEM bar


The optional OEM bar allows you to control the configuration of the functions ofthe connected machine tool, independently of its configuration.


Basic operation | OEM bar

3.10.1 Operating elements of the OEM bar

The operating elements that are available on the OEM bar depend onthe configuration of the device and of the connected machine tool.

The following operating elements are typically available in the OEM bar:

Operatingelement

Function

Tapping the tab shows or hides the OEM bar

LogoDisplays the configured OEM logo

Spindle speedShows one or more default values for the spindle speed

3


4Software

configuration

Software configuration | Overview 4

4.1 Overview

Make sure that you have read and understood the "Basic operation"chapter before carrying out the actions described below.Further information: "Basic operation", Page 17

Before you can use ND 7000 Demo correctly after successful installation, youneed to configure ND 7000 Demo. This chapter describes how to perform thefollowing settings:

Setting the languageActivating software optionsSelecting the product version (optional)Selecting the ApplicationCopying the configuration fileUploading the configuration data

4.2 Setting the languageThe user interface language is English. You can change to another language, ifdesired.


Tap UserThe logged-in user is indicated by a check markSelect the logged-in userThe language selected for the user is indicated by a nationalflag in the Language drop-down listSelect the flag for the desired language from the Languagedrop-down listThe user interface is displayed in the selected language


Software configuration | Activating software options

4.3 Activating software optionsWith ND 7000 Demo, you can also simulate characteristics and functions that aredependent on a software option. To do so, you must enable the software optionwith a license key. The required license key is stored in a license file in the ND7000 Demo folder structure.

You must read in the license file in order to enable the available software options.

Tap Settings in the main menuThe product settings are displayed

Tap ServiceOpen in sequence:

Software optionsActivate optionsTap Read license file

In the dialog box, select the storage location:Select Internal

Select User

Select the PcDemoLicense.xml license fileConfirm your selection with SelectTap OKThe license key is activatedTap OKYou are prompted to restart the productPerform a restartThe functions depending on the software options areavailable

4.4 Selecting the product version (optional)ND 7000 is available in different versions. These versions differ in their interfacesfor connectible encoders:

The ND 7013 versionThe ND 7013 I/O version with additional inputs and outputs for switchingfunctions

In the Settings menu, you can select the version that is to be simulated with ND7000 Demo


Tap ServiceTap Product designationSelect the desired versionYou are now prompted to perform a restartND 7000 Demo is ready for use in the desired version

4


Software configuration | Selecting the Application 4

4.5 Selecting the ApplicationThe demo software allows you to simulate the various applications that supportthe product. The Radial drilling application mode can be selected after activationof the pertinent software option.Further information: "Activating software options", Page 45

When you change the unit’s application mode, then all of the axissettings will be reset.


Tap ServiceOpen in the sequence

OEM areaSettings

In the Application drop-down list, select the Radial drillingapplication mode (software option)

4.6 Copying the configuration fileBefore you can load the configuration data in ND 7000 Demo, you must firstcopy the downloaded configuration file DemoBackup.mcc to an area that can beaccessed by ND 7000 Demo.

Move to the temporary storage folderFor example, copy the configuration file DemoBackup.mcc to the followingfolder: C: ► HEIDENHAIN ► [product name] ► ProductsMGE5 ► Mom► [product abbreviation] ► user ► User

In order for ND 7000 Demo to access the configuration fileDemoBackup.mcc, you must retain the following part of the path whenyou save the file: ► [product name] ► ProductsMGE5 ► Mom► [product abbreviation] ► user ► User.

The configuration file can be accessed by ND 7000 Demo


Software configuration | Uploading the configuration data

4.7 Uploading the configuration data

Before you can upload the configuration data, you must first activatethe license key.Further information: "Activating software options", Page 45

In order to configure ND 7000 Demo for use on the computer, you must uploadthe DemoBackup.mcc configuration file.

Tap Settings in the main menuThe product settings are displayed

Figure 11: Settings menu

Tap ServiceOpen in succession:

Back up and restoreRestore settingsComplete restoration

In the dialog, select the storage location:InternalUser

Select the DemoBackup.mcc configuration fileConfirm your selection with SelectThe settings are appliedYou are prompted to close the applicationTap OKND 7000 Demo is closed, and the Microsoft Windowswindow is closedRestart ND 7000 DemoND 7000 Demo is now ready for use

4


5Quick Start

Quick Start | Overview 5

5.1 OverviewThis chapter describes the machining of an example workpiece and will guide youstep by step through the unit’s different operating modes. You need to carry outthe following machining steps for successful production of the flange:

Machining step Mode of operation

Determine preset Manual operation

Machine a through hole Manual operation

Machine a fit MDI mode

Machine a bolt hole circle MDI mode

Machine a row of holes Programming and program run(software option)

The machining steps described here cannot be completely simulatedwith ND 7000 Demo. However, you can use the descriptions tofamiliarize yourself with the most important functions and the userinterface.

Figure 12: Example workpiece

This chapter does not describe the processing of the outside contourof the example workpiece. It is assumed that the outside contour hasalready been machined.

For a detailed description of the individual activities, please referto the "Manual operation" and "MDI mode" chapters as well as the"Programming" and "Program run" chapters in the operating instructionsND 7000.

Make sure that you have read and understood the "Basic operation"chapter before carrying out the actions described below.Further information: "Basic operation", Page 17


Quick Start | Logging in for Quick Start

5.2 Logging in for Quick Start

User login

For Quick Start, the Operator user must log in.

Tap User login in the main menuIf required, log out the user who is currently logged inSelect the Operator userTap the Password input fieldEnter the password "operator”

If the password does not match the defaultpassword, ask a Setup user or OEM user for theassigned password.If the password is no longer known, contact aHEIDENHAIN service agency.

Confirm entry with RETTap Log in

5


Quick Start | Requirements 5

5.3 RequirementsFor production of the aluminum flange, you will work on a manually operatedrapid radial drilling machine or radial drilling machine. The following dimensionedtechnical drawing is available for the flange:

Ø20

H6

Ø6.

1

13

10

M6

20

Ø50±0.1

100

90±0.1

50±

0.1

5±0.

1

140±

0.1

95±

0.1

145

AA

A-A

45°

8x45°

1x45°

Figure 13: Example workpiece – technical drawing

Machine

The machine is onA pre-processed workpiece blank is clamped on the machine

Product

A spindle axis is configured (only for the product with ID 1089179-xx)The calibration processes has been performedThe axes have been homedA HEIDENHAINKT 130 Edge Finder is available

Tools

The following tools are available:Drill Ø 5.0 mmDrill Ø 6.1 mmDrill Ø 19.8 mmReamer Ø 20 mm H6Countersink Ø 25 mm 90°M6 tap


Quick Start | Requirements

Tool table

For the example it is presumed that the tools for machining are not yet defined.For each tool used, you must therefore define the specific parameters in the tooltable of the product. During subsequent machining you can access the parametersin the tool table via the status bar.

Tap Tools on the status barThe Tools dialog box appears

Tap Open tableThe Tool table dialog box appears

Tap AddIn the Tool type input field, enter the name Drill 5.0Confirm the entry with RETIn the Diameter input field, enter the value 5.0Confirm the entry with RETIn the Length input field, enter the length of the drillConfirm the entry with RETThe defined Ø 5.0 mm drill is added to the tool tableRepeat this procedure for the other tools, and use thenaming convention [Type] [Diameter]Tap CloseThe Tool table dialog box is closed

5.4 Determining the preset (manual operation)You first need to determine the preset. Based on this preset, the product thencalculates all of the values for the relative coordinate system. Determine thepreset with the HEIDENHAIN KT 130 edge finder.

D: 0/0Y+

Y+

X+

Figure 14: Example workpiece – finding the preset

Activation


5


Quick Start | Determining the preset (manual operation) 5

Probing the preset

On the machine, insert the HEIDENHAINKT 130 edge finderinto the spindle, and connect it to the productTap Additional functions in the status bar

Tap Determining the alignment and preset via edges

The Select the tool dialog box opensIn the Select the tool dialog box, activate the Using touch-probes optionIn order to determine the alignment of the X axis, select theY+ probing direction (cf. figure)Tap Confirm in the wizardMove the edge finder toward the workpiece edge until thered LED on the edge finder lights upMeasuring point 1 is acquiredMove the edge finder to another position toward the edge ofthe workpiece until the red LED on the edge finder lights upMeasuring point 2 is acquiredIn order to determine the alignment of the Y axis, select theX+ probing direction (cf. figure)Tap Confirm in the wizardMove the edge finder toward the workpiece edge until thered LED on the edge finder lights upPoint 3 is acquiredThe Select preset dialog box opensEnter “0” in the Selected preset field

Tap Confirm in the wizardThe new preset is saved

5.5 Machining a through hole (manual operation)In the first machining step you drill the through hole in manual operation modeusing the Ø 5.0 mm drill. You then drill the through hole with the Ø 19.8 mmdrill. The values to be entered into the input fields can be taken directly from thedimensioned production drawing.

95

50

Figure 15: Example workpiece – drilling a through hole


Quick Start | Machining a through hole (manual operation)

Activation


5.5.1 Predrilling the through hole

On the machine, insert drill Ø 5.0 mm into the spindle

Tap Tools on the status barThe Tools dialog box appearsTap Drill 5.0Tap ConfirmThe associated tool parameters are applied automaticallyThe Tools dialog box is closedOn the product, set a spindle speed of 3500 rpmOn the radial drilling machine, move the spindles as follows:

X direction: 95 mmY direction: 50 mm

Predrill the through hole and retract the spindleKeep positions X and YYou have successfully predrilled the through hole

5.5.2 Boring the through hole

On the machine, insert drill Ø 19.8 mm into the spindle

Tap Tools on the status barThe Tools dialog box appearsTap Drill 19.8Tap ConfirmThe associated tool parameters are applied automaticallyThe Tools dialog box is closedOn the product, set a spindle speed of 400 rpm

Bore the through hole and retract the spindleYou have successfully bored the through hole

5


Quick Start | Machining a fit (MDI mode of operation) 5

5.6 Machining a fit (MDI mode of operation)Machine the fit in MDI mode of operation. The values to be entered into the inputfields can be taken directly from the dimensioned production drawing.

You should chamfer the through hole before reaming. The chamferenables a better first cut of the reamer and prevents burr formation.

Figure 16: Example workpiece – machining a fit

Activation




5.6.1 Defining the fit

Tap Tools on the status barThe Tools dialog box appearsTap ReamerTap ConfirmThe associated tool parameters are applied automaticallyThe Tools dialog box is closed

Tap Create on the status barA new block is displayedIn the Block type drop-down list, select the Hole block typeEnter the following parameters according to the dimensionaldata:

X coordinate: 95Y coordinate: 50Z coordinate: drill through

Confirm each entry with RETTo run the block, tap ENDThe positioning aid is displayedIf the simulation window is active, the position and traversepath are visualized


Quick Start | Machining a fit (MDI mode of operation)

5.6.2 Reaming the fit

On the machine, insert the Ø 20 mm H6 reamer into thespindleOn the product, set a spindle speed of 250 rpm

Start the machining process—follow the instructions of thewizardTap CloseProgram run is terminatedThe wizard closesYou have successfully machined the fit

5.7 Drilling a bolt hole circle (MDI mode)Drill the circular hole pattern in MDI mode. The values to be entered into the inputfields can be taken directly from the dimensioned production drawing.

Figure 17: Example workpiece – drilling a bolt hole circle

Activation




5


Quick Start | Drilling a bolt hole circle (MDI mode) 5

5.7.1 Defining the bolt hole circle

Tap Tools on the status barThe Tools dialog appearsTap Drill 6.1Tap ConfirmThe associated tool parameters are applied automaticallyThe Tools dialog is closed

Tap Create on the status barA new block is displayedIn the Block type drop-down list, select the Bolt hole circleblock typeEnter the following parameters according to the dimensionaldata:

Number of holes: 8X coordinate of center: 95Y coordinate of center: 50Radius: 25

Confirm each entry with RETKeep the default values for all the other valuesTo run the block, tap ENDThe positioning aid is displayedIf the simulation window is active, the rectangular pocket isvisualized

5.7.2 Drilling the bolt hole circle

On the machine, insert drill Ø 6.1 mm into the spindleOn the product, set a spindle speed of 3500 rpm

Drill the circular hole pattern and retract the spindle

Tap CloseProgram run is terminatedThe wizard closesYou have successfully completed the circular hole pattern


Quick Start | Programming a row of holes (programming)

5.8 Programming a row of holes (programming)Precondition: The PGM software option is activeThe row of holes is machined in Programming mode. You can reuse the programin a potential small batch production run. You can take the values directly from thedimensioned drawing and enter them in the input fields.

Figure 18: Example workpiece – programming a bolt hole circle and a row of holes

Calling up

Tap Programming in the main menu


The user interface for programming is displayed

5.8.1 Creating the program header

Tap Create new program in the program managementA dialog box is opened.In the dialog select the storage location, e.g.Internal/Programs in which you want to save the programEnter a name for the programConfirm the entry with RETTap CreateA new program containing the Program header start block iscreatedIn Name enter the name ExampleConfirm the entry with RETIn Unit for linear values select the mm unit of measureThe program has been successfully created; you can thenbegin with programming

5


Quick Start | Programming a row of holes (programming) 5

5.8.2 Programming the tool

Tap Add block on the toolbarA new block is inserted below the current positionIn the Block type drop-down list, select the Tool call blocktypeTap Tool numberThe Tools dialog appearsTap Drill 5.0The associated tool parameters are applied automaticallyThe Tools dialog is closed

Tap Add block on the toolbarA new block is inserted below the current positionIn the Block type drop-down list, select the Spindle speedblock typeIn Spindle speed, enter the value 3000Confirm the entry with RET

5.8.3 Programming the row of holes

Tap Add block on the toolbarA new block is inserted below the current positionIn the Block type drop-down list, select the Row of holesblock typeEnter the following values:

X coordinate of 1st hole: 5Y coordinate of 1st hole: 5Holes per row: 4Hole spacing: 45Angle: 0°

Depth: -13Number of rows: 3Row spacing: 45Fill mode: bolt hole circle

Confirm each entry with RETTap Save program in the program managementThe program is saved


Quick Start | Programming a row of holes (programming)

5.8.4 Simulating program runAfter you have successfully programmed the row of holes, you can simulate howthe program will run using the simulation window.

Figure 19: Example workpiece: simulation window

Tap Simulation windowThe simulation window is displayedTap each program block, one after the otherThe tapped machining step is shown in color in thesimulation windowCheck the view for programming errors, e.g. tool pathintersections of holesIf there are no programming errors, then you canmanufacture the row of holes

5.9 Machining a row of holes (program run)You have defined the individual machining steps for the row of holes in a program.You can execute the created program in Program run.

Figure 20: Example workpiece – drilling a row of holes

5


Quick Start | Machining a row of holes (program run) 5

5.9.1 Opening the program

Tap Program run in the main menu


The user interface for Program Run is displayedTap Open program in the program managementA dialog box is opened.Select the Internal/Programs storage location in the dialogTap the file Example.iTap OpenThe selected program is opened

5.9.2 Running a program

On the radial drilling machine, insert drill Ø 5.0 mm into thespindleTap NC START on the program controlThe product highlights the program’s first Tool call blockThe wizard displays the relevant instructionsTap NC START again to begin machiningThe spindle speed is set, and the first machining block ishighlightedThe individual steps of the Row of holes machining block aredisplayedThe axis move to the first positionDrill all the way through with the Z axisCall the next step in the Row of holes machining block withNextThe next step is calledMove the axes to the next positionFollow the instructions in the wizardAfter you have drilled the row of holes, tap CloseMachining is terminatedThe program is resetThe wizard is closed


6ScreenshotClient

ScreenshotClient | Overview 6

6.1 OverviewThe standard installation of ND 7000 Demo also contains the ScreenshotClientprogram. With ScreenshotClient, you can take screenshots of the demo softwareor the unit.This chapter describes how ScreenshotClient is configured and used.

6.2 Information about ScreenshotClientWith ScreenshotClient, you can take screenshots of the active screen of thedemo software or the unit from a computer. Before taking a screenshot, select thedesired user interface language, as well as the file name and the location whereyou want to store the screenshots.ScreenshotClient creates image files of the desired screen:

In .PNG formatWith the configured nameWith the appropriate language codeWith the time information of year, month, day, hour, minute, and second

1

2

4

3

Figure 21: ScreenshotClient user interface

1 Connection status2 File path and file name3 Language selection4 Status messages


ScreenshotClient | Starting ScreenshotClient

6.3 Starting ScreenshotClientSelect in succession in Microsoft Windows:


ND 7000 Demo

ScreenshotClientScreenshotClient is started:

Figure 22: ScreenshotClient has been started (not connected yet)

You can now connect ScreenshotClient with the demo software or the product

6.4 Connecting ScreenshotClient with the demo software

Before establishing a connection with ScreenshotClient, first start thedemo software or switch on the unit. Otherwise ScreenshotClient willshow the status message Connection close. when trying to connect.

Start the demo software if you have not already done soFurther information: "Starting the ND 7000 Demo", Page 22Tap ConnectA connection with the demo software is establishedThe status message is updatedThe Identifier and Language input fields become active

6


ScreenshotClient | Connecting ScreenshotClient with the unit 6

6.5 Connecting ScreenshotClient with the unitPrerequisite: The network must be configured on the device.

For detailed information on configuring the network at the unit, pleaserefer to the “Setup” chapter in the operating instructions of ND 7000.

Before establishing a connection with ScreenshotClient, first start thedemo software or switch on the unit. Otherwise ScreenshotClient willshow the status message Connection close. when trying to connect.

Switch on the unit if you have not already done soEnter the IPv4 address of the interface in the Connection input field.You will find the address in the device settings under:Interfaces ► Network ► X116Tap ConnectA connection with the unit is establishedThe status message is updatedThe Identifier and Language input fields become active

6.6 Configuring ScreenshotClient for taking screenshotsOnce you have started ScreenshotClient, you can make the followingconfigurations:

Location at which screenshots are stored, and what the file names areUser interface language in which the screenshots are created

6.6.1 Configuring the storage location and file name for screenshotsBy default, ScreenshotClient saves screenshots to the following storage location:C: ► HEIDENHAIN ► [product designation] ► ProductsMGE5 ► Mom► [product code] ► sources ► [file name]

You can define a different storage location, if necessary.Tap the Identifier input fieldEnter the path to the storage location and the name for the screenshots intothe Identifier input field

Use the following syntax to enter the path and file name forscreenshots:[drive]:\[folder]\[file name]

ScreenshotClient will save all screenshots to the storage location entered


ScreenshotClient | Configuring ScreenshotClient for taking screenshots

6.6.2 Configuring the user interface language of screenshotsThe Language input field shows all of the user interface languages availablefor the demo software or the unit. Once you have selected a language code,ScreenshotClient will take screenshots in the corresponding language.

The user interface language you are using in the demo software or onthe unit does not have any effect on the screenshots. Screenshotsare always created in the language that you have selected inScreenshotClient.

Screenshots in the desired user interface language

To take screenshots in a desired user interface language

Use the arrow keys to select the desired language code inthe Language input fieldThe selected language code is shown in redScreenshotClient creates the screenshots in the desired userinterface language

Screenshots of all available user interface languages

To create screenshots in all available user interface languages

Use the arrow keys to select all in the Language input fieldThe all language code is shown in redScreenshotClient creates the screenshots in all available userinterface languages

6


ScreenshotClient | Creating screenshots 6

6.7 Creating screenshotsIn the demo software or on the unit, call the view from which you would like totake a screenshotSwitch to ScreenshotClientTap SnapshotThe screenshot is created and saved to the configured storage location

The screenshot is saved in the format [file name]_[languagecode]_[YYYYMMDDhhmmss] (e.g. screenshot_en_20170125114100)

The status message is updated:

Figure 23: ScreenshotClient after screenshot has been created successfully

6.8 Exiting ScreenshotClientTap Disconnect

The connection to the demo software or the unit is terminatedTap CloseScreenshotClient is exited


7 Index

C

code number.............................. 23Configuration data

Copying the file...................... 46Uploading the file................... 47

ConfiguringFile name for screenshots..... 66ScreenshotClient................... 66Software................................ 44Storage location for screenshots66User interface language ofscreenshots........................... 67

D

Demo softwareFeatures................................... 8Intended use............................ 8

DocumentationNotes on reading..................... 8

Dragging..................................... 19

E

ExampleCircular hole pattern (MDImode)..................................... 57fit (MDI mode of operation)... 56Flange drawing...................... 52Preset (Manual operation)...... 53Row of holes (programming).. 59Row of holes (program run)... 61through hole (manual operationmode)..................................... 54workpiece.............................. 50

ExitingScreenshotClient................... 68

F

File managementMenu..................................... 33

G

GesturesDragging................................ 19Holding................................... 19Operation............................... 18Tapping.................................. 18

H

Holding....................................... 19

I

Input devicesOperation............................... 18

Installation fileDownloading.......................... 12

L

Languagesetting.............................. 24, 44

M

Main menu................................. 25Manual operation....................... 27

Example................................. 53menu..................................... 27

Manual operation modeexample................................. 54

MDImenu..................................... 28

MDI modeExample................................. 57

MDI mode of operationexample................................. 56

MenuFile management................... 33manual operation................... 27MDI........................................ 28Programming......................... 31Settings.................................. 35Switch-off............................... 36User login.............................. 34

Mouse actionsDragging................................ 19Holding................................... 19Operation............................... 18Tapping.................................. 18

O

OEM bar.................................... 40Operating elements............... 41

Operating elementsadd......................................... 21back....................................... 21close...................................... 21confirm................................... 21drop-down list........................ 20Main menu............................ 25OEM bar................................ 41plus/minus button.................. 20Screen keyboard.................... 20slide switch............................ 20status bar............................... 38toggle switch......................... 20undo....................................... 21

OperationGeneral operation.................. 18Gestures and mouse actions. 18Operating elements............... 20Touchscreen and inputdevices................................... 18

P

Password

default password................... 51Preset

Probing................................... 40Product version.......................... 45Programming

Example................................. 59Menu..................................... 31

Program runExample................................. 61Menu..................................... 30

Q

Quick start.................................. 50

S

ScreenshotClient........................ 64Configuring............................ 66Connecting............................. 65Creating screenshots............. 68Exiting.................................... 68Information............................ 64Starting.................................. 65

ScreenshotsConfiguring the file name....... 66Configuring the storagelocation.................................. 66Configuring the user interfacelanguage................................ 67Creating................................. 68

Selecting the application............ 46Settings

Menu..................................... 35Shut-down

Software................................ 23Software

Configuration data............ 46, 47Downloading the installationfile.......................................... 12Enabling functions................. 45installation.............................. 13Shut-down............................. 23Starting.................................. 22System requirements............ 12Uninstallation......................... 15

Software optionsActivating............................... 45

StartingScreenshotClient................... 65Software................................ 22

Status bar................................... 38operating elements................ 38

Switch-offMenu..................................... 36

Symbols and fonts used formarking text................................. 9

7


Index7

T

Tapping....................................... 18Tool table

Creating................................. 53Touchscreen

Operation............................... 18

U

UseImproper.................................. 8Intended................................... 8

UserDefault password................... 23Login...................................... 23Logout.................................... 23User login.............................. 23

User interfaceAfter startup........................... 24File management menu......... 33Main menu............................ 25manual operation menu......... 27MDI menu............................. 28Programming menu............... 31Program run menu................. 30Settings menu....................... 35Switch-off menu..................... 36User login menu.................... 34

User login............................ 23, 34


List of figures

8 List of figures

Figure 1: Installation wizard................................................................................................................. 13Figure 2: Installation wizard with activated options Demo software and Screenshot Utility............. 14Figure 3: User login menu......................................................................................................................22Figure 4: MDI block dialog box............................................................................................................... 29Figure 5: Program run menu..................................................................................................................30Figure 6: Programming menu.................................................................................................................31Figure 7: Programming menu with opened simulation window............................................................32Figure 8: File management menu......................................................................................................... 33Figure 9: User login menu......................................................................................................................34Figure 10: Settings menu......................................................................................................................... 35Figure 11: Settings menu......................................................................................................................... 47Figure 12: Example workpiece..................................................................................................................50Figure 13: Example workpiece – technical drawing................................................................................. 52Figure 14: Example workpiece – finding the preset.................................................................................53Figure 15: Example workpiece – drilling a through hole.......................................................................... 54Figure 16: Example workpiece – machining a fit......................................................................................56Figure 17: Example workpiece – drilling a bolt hole circle....................................................................... 57Figure 18: Example workpiece – programming a bolt hole circle and a row of holes.............................. 59Figure 19: Example workpiece: simulation window................................................................................. 61Figure 20: Example workpiece – drilling a row of holes.......................................................................... 61Figure 21: ScreenshotClient user interface.............................................................................................. 64Figure 22: ScreenshotClient has been started (not connected yet)......................................................... 65Figure 23: ScreenshotClient after screenshot has been created successfully......................................... 68

8


DR. JOHANNES HEIDENHAIN GmbHDr.-Johannes-Heidenhain-Straße 583301 Traunreut, Germany +49 8669 31-0 +49 8669 32-5061E-mail: [email protected]

Technical support +49 8669 32-1000Measuring systems +49 8669 31-3104

E-mail: [email protected] support +49 8669 31-3101

E-mail: [email protected] programming +49 8669 31-3103



E-mail: [email protected]

www.heidenhain.de

Original document1308773 · 00 · A · 02 · 01/2020 · PDF *I1308773*

Documents

ND 7000 Demo - heidenhain.fr...To enter data, you can use the screen keyboard of the touchscreen or a connected keyboard. 3.2.2 Gestures and mouse actions To activate, switch or move