Upload
others
View
21
Download
0
Embed Size (px)
Citation preview
NeoGate TA1600/2400/3200 User Manual
2/63
Table of Contents
Introduction ..................................................................................... 4
Part I. Configuration Guide ............................................................... 5
1. Login ............................................................................................ 5
2. Status ........................................................................................... 7
2.1 System Status ............................................................................ 7 2.1.1 Port Status ........................................................................... 7 2.1.2 Network status ...................................................................... 8 2.1.3 System Info .......................................................................... 8
2.2 Reports ..................................................................................... 9 2.2.1 Call Logs .............................................................................. 9 2.2.2 System Logs ......................................................................... 9 2.2.3 Packet Tool ..........................................................................10
3. System ....................................................................................... 10
3.1 Network Preferences ..................................................................11 3.1.1 LAN Settings ........................................................................11 3.1.2 Service ...............................................................................12 3.1.3 VLAN Settings ......................................................................12 3.1.4 VPN Settings ........................................................................14 3.1.5 DDNS Settings .....................................................................15 3.1.6 Static Route .........................................................................15 3.1.7 SNMP Settings .....................................................................16
3.2 Security Center..........................................................................17 3.2.1 Security Center ....................................................................17 3.2.2 Alert settings .......................................................................19 3.2.3 AMI Settings ........................................................................21 3.2.4 Certificates ..........................................................................22 3.2.5 Firewall Rules .......................................................................23 3.2.6 IP Blacklist ..........................................................................24
3.3 System Preferences ....................................................................25 3.3.1 Password settings .................................................................25 3.3.2 Date and Time .....................................................................26 3.3.3 Email Settings ......................................................................26 3.3.4 Auto Provision Settings..........................................................27 3.3.5 Firmware Update ..................................................................30 3.3.6 Backup and Restore ..............................................................30 3.3.6 Reset and Reboot .................................................................31
4. Gateway ..................................................................................... 31
4.1 FXS Port List .............................................................................32 4.1.1 FXS Port List ........................................................................32
NeoGate TA1600/2400/3200 User Manual
3/63
4.1.2 Hunt Group .........................................................................38 4.2 VoIP Settings ............................................................................40
4.2.1 VoIP Server Settings .............................................................40 4.2.2 Dial Pattern Template ............................................................43 4.2.3 SIP Settings.........................................................................44 4.2.4 IAX Settings ........................................................................50
4.3 Gateway Settings .......................................................................51 4.3.1 General Preferences ..............................................................51 4.3.2 Feature Codes ......................................................................51 4.3.3 Speed Dial Settings ..............................................................54
4.4 Audio Settings ...........................................................................54 4.4.1 Custom Prompts ...................................................................54 4.4.2 Music on Hold Prompts ..........................................................55 4.4.3 System Prompts Settings .......................................................56
4.5 Advanced Settings .....................................................................57 4.5.1 Tone Zone Settings ...............................................................57 4.5.2 RADIUS Settings ..................................................................59
Part II. Basic Operations ................................................................ 60
1. NeoGate TA Voice Menu ..............................................................60 2. Inter-port Call ...........................................................................61 3. Call Hold ...................................................................................61 4. Call Waiting ...............................................................................61 5. Call Transfer ..............................................................................62 7. Direct IP Call .............................................................................62 8. Change NeoGate TA’s IP Address Using Analog Phones ....................63
NeoGate TA1600/2400/3200 User Manual
4/63
Introduction NeoGate TA1600/2400/3200 FXS Analog VoIP Gateways are cutting-edge products that connect legacy telephones, fax machines and PBX systems with IP telephony networks and IP-based PBX systems. Featuring rich functionalities and easy configuration, NeoGate TA is ideal for small and medium enterprises that wish to integrate a traditional phone system into IP-based system. NeoGate TA helps them to preserve previous investment on legacy telephone system and reduce communication costs significantly with the true benefits of VoIP.
Features ● 16/24/32 FXS ports ● Fully compliant with SIP and IAX2 ● Dial Pattern of outgoing calls ● Hunt Group ● Configurable VoIP Server templates ● Reliable fax performance with T.38 ● 3-party Conference ● Inter-port Calling ● Call Hold ● Blind Transfer ● Attended Transfer ● Support RADIUS protocol For more information, please click: http://www.yeastar.com/Products/Products.asp#NeoGateTA For more information about the NeoGate TA hardware specification and how to install the NeoGate TA, please refer to the document below: http://www.yeastar.com/download/PartI_NeoGate_TA_FXS_Gateway_Installation_Guide_en.pdf
NeoGate TA1600/2400/3200 User Manual
5/63
Part I. Configuration Guide 1. Login The NeoGate TA attempts to contact a DHCP server in your network to obtain valid network settings (e.g., the IP address, subnet mask, default gateway address and DNS address) by default. Please enable DHCP Server in your network to obtain the NeoGate IP address. How to check NeoGate TA IP address: 1. Pick up the analog phone, then access the voice menu prompt by dialing “***”. 2. Dial "1" to check the IP address. 3. Dial "2" for web access address. Logging On: After entering the IP address in the web browser, users will see a log-in screen. Check the default settings below: Username: admin Password: password In this example, the IP address is 192.168.7.101, the model is TA2400.
NeoGate TA1600/2400/3200 User Manual
6/63
Figure 1-1 NeoGate TA Login page
Click "Login" to get the welcome page.
Figure 1-2 Login NeoGate TA
NeoGate TA1600/2400/3200 User Manual
7/63
2. Status
Click to check the status of NeoGate TA, including the system status and the detailed reports.
2.1 System Status
In this page, we can check the status of the system, including trunk status, network status and system information.
2.1.1 Port Status
Figure 2-1 FXS Port Status
NeoGate TA Status Description:
Port Status:
Up/Down Description Up The FXS module works well. Down The FXS module is broken.
Voice Mail (New/Old) Showing the number of unread voicemail and old voicemail.
*Only when the FXS port is registered as one of the VoIP Server’s accounts, can you see the voice mail status.
Status:
Status Description OK Successful registration, trunk is ready for use
Unreachable The trunk is unreachable. Request Send Registering. Waiting for authentication Wrong password or user name. Failed Trunk registration failed.
NeoGate TA1600/2400/3200 User Manual
8/63
Off-hook/On-hook
Hook Description On Hook The FXS port is idle. Off Hook The FXS port is busy.
2.1.2 Network status
In this page, the IP address of LAN port will appear with their status.
Figure 2-2 Network Status
If your VLAN or VPN are configured, you can check the status in this page also.
2.1.3 System Info
In this page, we can check the hardware/firmware version, or the disk usage of NeoGate TA.
Figure 2-3 System Info
NeoGate TA1600/2400/3200 User Manual
9/63
2.2 Reports
In this page, we can check the call detailed log, system log, and use the packet tool to debug the system when needed.
2.2.1 Call Logs
The call log captures all call details, including call time, caller number, callee number, call type, call duration, etc. An administrator can search and filter call data by call date, caller/callee, trunk, duration, billing duration, status, or communication type.
Figure 2-4 Call Logs
2.2.2 System Logs
You can download and delete the system logs of NeoGate TA.
Figure 2-5 System Logs
NeoGate TA1600/2400/3200 User Manual
10/63
Options ·Enable Hardware Log Save the information of hardware; (up to 4 log files) ·Enable Normal Log Save the prompt information; (up to 16 log files) ·Enable Web Log Save the history of web operations (up to 2 log files) ·Enable Debug Log Save debug information (up to 2 log files)
2.2.3 Packet Tool
This feature is used to capture packets for technician. Integrate packet capture tool “Wireshark” in NeoGate. Users also could specify the destination IP address and port to get the packets. ·IP Specify the destination IP address to get the packets. ·Port Specify the destination Port to get the packets.
3. System
Click to access. In this page, we can configure the network settings,
security settings and some system preferences.
NeoGate TA1600/2400/3200 User Manual
11/63
3.1 Network Preferences
3.1.1 LAN Settings
Figure 3-1 Static IP Address Mode
Table 3-1 Description of LAN Settings Items Description Hostname Set the host name for NeoGate TA Static IP Address Set the NeoGate TA’s IP address as a static IP
IP Address Set the IP Address for NeoGate TA. It is recommended that you configure a static IP address for NeoGate TA.
Subnet Mask Set the subnet mask for NeoGate TA Gateway Set the gateway for NeoGate TA Primary DNS Set the primary DNS for NeoGate TA. Secondary DNS Set the secondary DNS for NeoGate TA IP Address2 Set the second IP Address for NeoGate TA Subnet Mask2 Set the second subnet mask for NeoGate TA
Figure 3-2 DHCP Mode
Select DHCP mode to get network automatically from the local network.
Figure 3-3 PPPoE
Fill in user name and password to access the Internet via PPPoE.
NeoGate TA1600/2400/3200 User Manual
12/63
3.1.2 Service
The administrator can manage all the access methods on NeoGate TA on the "Service" page.
Figure 3-4 Service Settings
Table 3-2 Description of Service Settings
Items Description
SSH
By using SSH, you can log in to NeoGate and run commands. It's disabled by default. We don't recommend enabling it if not needed. The default port for SSH is 8022;
FTP FTP access; The default port is 21.
TFTP TFTP access; The default port is 23.
HTTP HTTP web access; The default port is 80.
HTTPS HTTPS web access, it is disabled by default, and you can enable it to get safer web access.
3.1.3 VLAN Settings
A VLAN (Virtual LAN) is a logical local area network (or LAN) that extends beyond a single traditional LAN to a group of LAN segments, given specific configurations. Note: NeoGate TA is not the VLAN server, a 3-layer switch is still needed, please configure the VLAN information there first, then input the details in NeoGate TA, so that the packages via NeoGate TA will be added the VLAN label before
NeoGate TA1600/2400/3200 User Manual
13/63
sending to that switch.
Figure 3-5 VLAN Settings
Table 3-3 Description of VLAN Settings
Items Description NO.1 Click the NO.1 you can edit the first VLAN over LAN
VLAN Number The VLAN Number is a unique value you assign to each VLAN on a single device
VLAN IP Address Set the IP Address for NeoGate TA VLAN over LAN. VLAN Subnet Mask Set the Subnet Mask for NeoGate TA VLAN over LAN. Default Gateway Set the Default Gateway for NeoGate TA VLAN over LAN NO.2 Click the NO.2 you can edit the first VLAN over LAN.
VLAN Number The VLAN Number is a unique value you assign to each VLAN on a single device.
VLAN IP Address Set the IP Address for NeoGate TA VLAN over LAN. VLAN Subnet Mask Set the Subnet Mask for NeoGate TA VLAN over LAN. Default Gateway Set the Default Gateway for NeoGate TA VLAN over LAN.
NeoGate TA1600/2400/3200 User Manual
14/63
3.1.4 VPN Settings
A virtual private network (VPN) is a method of computer networking typically using the public internet that allows users to privately share information between remote locations, or between a remote location and a business' home network. A VPN can provide secure information transport by authenticating users, and encrypting data to prevent unauthorized persons from reading the information transmitted. The VPN can be used to send any kind of network traffic securely. NeoGate TA supports OpenVPN.
Figure 3-6 VPN Settings
·Enable VPN ·Import VPN Config Import configuration file of OpenVPN. Notes: 1. Don't configure “user” and “group” in the “config” file. You can get the config package from the OpenVPN provider. 2. NeoGate TA works as VPN client mode only.
NeoGate TA1600/2400/3200 User Manual
15/63
3.1.5 DDNS Settings
DDNS (Dynamic DNS) is a method / protocol / network service that provides the capability for a networked device, such as a router or computer system using the Internet Protocol Suite, to notify a Domain Name System (DNS) name server to change, in real time, the active DNS configuration of its configured hostnames, addresses or other information.
Figure 3-7 DDNS Settings
Table 3-4 Description of DDNS Settings
Items Description DDNS Server Select the DDNS server you sign up for service. User Name User name the DDNS server provides you. Password User account’s password. Host Name The host name you have got from the DDNS server Note: DDNS allows you to access your network using domain names instead of IP address. The service manages changing IP address and updates your domain information dynamically. You must sign up for service through dyndns.org, freedns.afraid.org, www.no-ip.com, www.zoneedit.com.
3.1.6 Static Route
NeoGate TA will have more than one Internet connection in some situations but it has only one default gateway. You will need to set some Static Route for NeoGate TA to force it to go out through different gateway when accessing to different internet. The default gateway priority of NeoGate TA from high to low is VPN/VLAN LAN port.
NeoGate TA1600/2400/3200 User Manual
16/63
Figure 3-8 Static Route
1) Route Table The current route rules of NeoGate TA. 2) Static Route Rules You can add new static route rules here.
Table 3-5 Description of Static Route Settings
Items Description Destination The destination network to be accessed to by NeoGate TA. Subnet Mask Specify the destination network portion.
Gateway Define which gateway NeoGate TA will go through when accessing the destination network.
Metric
The cost of a route is calculated by using what are called routing metric. Routing metrics are assigned to routes by routing protocols to provide measurable statistic which can be used to judge how useful (how low cost) a route is.
Interface Define which internet port to go through.
3.1.7 SNMP Settings
Simple Network Management Protocol (SNMP) is an Internet-standard protocol for managing devices on IP networks. NeoGate TA gateway supports three versions: V1, V2C and V3.
NeoGate TA1600/2400/3200 User Manual
17/63
Figure 3-9 SNMP Settings
3.2 Security Center
3.2.1 Security Center
You can check NeoGate TA security configuration in “Security Center” page. And also, you can enter the relevant security settings page rapidly.
NeoGate TA1600/2400/3200 User Manual
18/63
Firewall:
Figure 3-10 Firewall
In the “Firewall” tab, you can check firewall configuration and alert settings. You can enter the configuration page directly by clicking the relevant button. Service:
Figure 3-11 Service
In “Service” tab, you can check AMI /SSH/FTP/TFTP/HTTP/HTTPS status. You can enter the configuration page directly by clicking the relevant button. Port:
Figure 3-12 Port
In “Port” tab, you can check SIP port, HTTP port and HTTPS port. You can also enter the relevant page by clicking the button in “Setting” column. We recommend changing the default port for security.
NeoGate TA1600/2400/3200 User Manual
19/63
3.2.2 Alert settings
If the device is under attack, the system will alert users via call or E-mail. The attack modes include IP attack and Web Login.
Figure 3-13 Alert Settings
1. IPATTACK When the system is attacked by IP address, the firewall will add the IP to auto IP Blacklist and notify the user if it matches the protection rule. 1) Phone Notification Settings
Table 3-6 Description of Phone Notification Settings Items Description PHONE Notification Whether to enable phone notification or not.
Number
The numbers could be set for alert notification; users can setup multiple extension and outbound phone numbers. Please separate them by “;”. Example: “500;9911”, if the extension has configured Follow Me Settings, the call would go to the forwarded number directly.
Attempts The attempts to dial a phone number when there is no answer.
Interval The interval between each attempt to dial the phone number. Must be longer than 3 seconds, the default value is 60 seconds.
Prompt Users will hear the prompt while receiving the phone notification.
2) E-mail Notification Settings Note: Please ensure that all voicemail settings are properly configured on the System Settings -> Voicemail Settings page before using this feature.
Table 3-7 Description of E-mail Notification Settings Items Description E-mail Notification Whether to enable E-mail Notification or not.
Recipient’s Name The recipients for the alert notification, and multiple email addresses are allowed, please separate them by “;”. E.g. [email protected];[email protected],[email protected]
NeoGate TA1600/2400/3200 User Manual
20/63
Subject The subject of the alert email.
Email Content
Text content supports predefined variables. Variable names and corresponding instructions are as follows: gateway hostname:$(HOSTNAME) attack source ip address:$(SOURCEIP) attack dest mac:$(DESTMAC) attack source port:$(DESTPORT) attack source protocol:$(PROTOCOL) attack occurred:$(DATETIME)
Figure 3-14 IP ATTACK Alert
NeoGate TA1600/2400/3200 User Manual
21/63
2. WEBLOGIN Web Login Alert Notification: entering the wrong password consecutively for five times when logging in NeoGate TA Web interface will be deemed as an attack, the system will limit the IP login within 10 minutes and notify the user.
Figure 3-15 WEBLOGIN Alert
3.2.3 AMI Settings
The Asterisk Manager Interface (AMI) is a system monitoring and management interface provided by Asterisk. It allows live monitoring of events that occur in the system, as well enabling you to request that Asterisk perform some action. The actions that are available are wide-ranging and include things such as returning status information and originating new calls. Many interesting applications have been developed on top of Asterisk that take advantage of the AMI as their primary interface to Asterisk. There are two main types of messages on the Asterisk Manager Interface: manager events and manager actions. The 3rd party software can work with NeoGate TA using AMI interface. It is disabled by default. If necessary, you can enable it.
NeoGate TA1600/2400/3200 User Manual
22/63
Figure 3-16 AMI Settings
Username & password: after enabling AMI, you can use this username and password to log in NeoGate TA AMI. Permitted "IP address/Subnet mask": you can set which IP can log in NeoGate TA AMI interface.
3.2.4 Certificates
NeoGate TA can support TLS trunk. Before you register TLS trunk to NeoGate TA, you should upload certificates first.
Figure 3-17 Certificates
Trusted Certificate This certificate is a CA certificate. When selecting “TLS Verify Client” as “Yes”, you should upload a CA. The relevant IPPBX should also have this certificate. Gateway Certificate This certificate is server certificate. No matter selecting “TLS Verify Client” as “Yes” or “NO”, you should upload this certificate to NeoGate TA. If IPPBX
NeoGate TA1600/2400/3200 User Manual
23/63
enables “TLS Verify server”, you should also upload this certificate on IPPBX.
3.2.5 Firewall Rules
Figure 3-18 Firewall Rules
1) General Settings
Table 3-8 Description of Firewall General Settings
Items Description
Enable Firewall Enable the firewall to protect the device. You should reboot the device to make the firewall run.
Disable Ping Enable this item to drop net ping from remote hosts.
Drop All
When you enable “Drop All” feature, the system will drop all packets or connection from other hosts if there are no other rules defined. To avoid locking the devices, at least one “TCP” accept common rule must be created for port used for SSH access, port used for HTTP access and port sued for CGI access.
2) Common Rules There is no default rule; you can create one as required.
NeoGate TA1600/2400/3200 User Manual
24/63
Figure 3-19 Common Rule
Table 3-9 Description of Common Rule Settings Items Description Name A name for this rule, e.g. “HTTP”.
Description Simple description for this rule. E.g. Accept the specific host to access the web interface for configuration.
Protocol The protocols for this rule.
Port Initial port should be on the left and end port should be on the right. The end port must be equal to or greater than start port.
IP
The IP address for this rule. The format of IP address is: IP/mask E.g. 192.168.5.100/255.255.255.255 for IP 192.168.5.100 E.g. 192.168.5.0/255.255.255.0 for IP from 192.168.5.0 to 192.168.5.255 .
MAC Address
The format of MAC Address is XX:XX:XX:XX:XX:XX, X means 0~9 or A~F in hex, the A~F are not case sensitive.
Action Accept: Accept the access from remote hosts. Drop: Drop the access from remote hosts. Ignore: Ignore the access.
Note: The MAC address will be changed when it’s a remote device, so it will not be working to filter using MAC for remote devices.
3.2.6 IP Blacklist
You can set some packets accept speed rules here. When an IP address which hasn’t been accepted in common rules sends packets faster than the allowed speed, it will be set as a black IP address and be blocked automatically.
NeoGate TA1600/2400/3200 User Manual
25/63
Figure 3-20 IP Blacklist
1) Blacklist rules We can add the rules for IP blacklist rate as demanded.
Figure 3-21 Auto Blacklist Rule
Table 3-10 Description of Auto Blacklist Rule Settings Items Description Port Auto defense port Protocol Auto defense protocol. TCP or UDP. IP Packets Allowed IP packets number in the specific time interval.
Time interval The time interval to receive IP packets. For example, IP packets 90, time interval 60 means 90 IP packets are allowed in 60 seconds.
2) IP blacklist The blocked IP address will display here, you can edit or delete it as you wish.
3.3 System Preferences
In this page, we can set other system preferences, like the password for admin account, system date and time, firmware update, backup and restore, reset and reboot.
3.3.1 Password settings
The default password is “password”. To change the password, enter the new password and click "Save". The system will then prompt you to re-login using
NeoGate TA1600/2400/3200 User Manual
26/63
your new password.
Figure 3-22 Password Settings
3.3.2 Date and Time
Set the date and time for NeoGate TA.
Figure 3-23 Date & Time
Table 3-11 Description of Date & Time Settings
Items Description Time Zone You can choose your time zone here. Daylight Saving Time Set the mode to Automatic or disabled. Automatically Synchronize With an Internet Time Server
Input the NTP server so that NeoGate TA will update the time automatically.
Set Date & Time Manually You can set the time to your local time manually here.
3.3.3 Email Settings
To send the system alert to email address, please configure the Email settings first, and make sure SMTP test is successful.
NeoGate TA1600/2400/3200 User Manual
27/63
Figure 3-24 Email Settings
Table 3-12 Description of SMTP Settings
Items Description
E-mail Address The E-mail Address that NeoGate TA will use to send voicemail.
Password The password for the email address used above
SMTP Server
The IP address or hostname of an SMTP server that the NeoGate TA will connect to in order to send voicemail messages via email, i.e. mail.yourcompany.com.
Port SMTP Port: the default value is 25.
Use SSL/TLS to send secure message to server
If the server of sending email needs to authenticate the sender, you need to enable this Note: Must be selected for Gmail or exchange server.
After filling out the above information, you can click on the “Test Account Settings” button to check whether the setup is OK. 1) If the test is successful, you can use the email safely. 2) If test failed, please check if the above information is correct or if the network is proper.
3.3.4 Auto Provision Settings
This feature is used along with MyPBX "NeoGate Provisioning". Users can configure NeoGate TA on MyPBX "NeoGate Provisioning" page.
NeoGate TA1600/2400/3200 User Manual
28/63
Figure 3-25 MyPBX NeoGate Provisioning
Add NeoGate Click “Add NeoGate” and fill in the corresponding information in the pop-up window.
Figure 3-26 General Settings
1) General ·MAC Address Fill in the MAC address of the NeoGate. ·MAC Address Select the NeoGate Type. .Label Fill in the name of the NeoGate. ·Key as Send Configure a key as the send key, you can choose #, * or disable this feature. 2) Codecs In this page, you can set the codecs for the NeoGate.
NeoGate TA1600/2400/3200 User Manual
29/63
Figure 3-27 Codec Settings
3) LAN Settings Configure the network of NeoGate on this page.
Figure 3-28 LAN Settings
4) Extensions Configure each line of NeoGate.
NeoGate TA1600/2400/3200 User Manual
30/63
Figure 3-29 Extensions Settings Two Methods are supported for NeoGate provision: PnP and DHCP. If DHCP method is selected, you should enable DHCP Server on MyPBX (System→ Network Preferences→DHCP Server).
Figure 3-30 NeoGate TA Gateway Auto Provision
3.3.5 Firmware Update
Firmware upgrading is possible through the Administrator Web interface using a TFTP Server or an HTTP URL. Enter your TFTP Server IP address and firmware file location, then click "Start" to update the firmware Notes: 1. If “Reset configuration to Factory Defaults” is enabled, the system will restore to factory default settings. 2. When updating the firmware, please don’t turn off the power. Or the system will get damaged.
Figure 3-31 Firmware Update
3.3.6 Backup and Restore
We can back up the configurations before resetting NeoGate TA to factory defaults, and then restore it on this package.
NeoGate TA1600/2400/3200 User Manual
31/63
Figure 3-32 Backup and Restore
Notes: 1. Only configurations, custom prompts will be backed up. 2. If you have updated the firmware version, it’s not recommended to restore
using old package.
3.3.6 Reset and Reboot
We can reset or reboot NeoGate TA directly in this page.
Figure 3-33 Reset and Reboot
·Reboot System Warning: Rebooting the system will terminate all active calls! ·Reset to Factory Defaults Warning: A factory reset will erase all configuration data on the system. Please do not turn off the system until the RUN light begins blinking. Any power interruption during this time could cause damage to the system.
4. Gateway
Click to access the gateway configuration page. Users can configure the details of FXS ports, VoIP settings, gateway settings and advanced settings.
NeoGate TA1600/2400/3200 User Manual
32/63
4.1 FXS Port List
4.1.1 FXS Port List
All the FXS ports are listed here. You can edit each FXS port by clicking the "Edit" button. Batch editing the FXS ports number and batch editing FXS ports are available.
Figure 4-1 FXS Port List
1) Edit the FXS port
Click "Edit" button to configure the FXS port.
NeoGate TA1600/2400/3200 User Manual
34/63
> General Table 4-1 Description of FXS Port General Settings
Items Description
General Port The corresponding port.
Number User account number.
VoIP Serer Template
Primary Server Choose the Primary VoIP server, where the account will be registered.
Failover Server Choose the failover server for the account. This server will be used if the primary server is unavailable.
User Name
Username of the account. Used for VoIP trunk registration. The user name should be entered if the "Enable Register" is checked on the VoIP Server.
Authentication Name
Used for SIP authentication. The authentication name should be entered if "Enable Register" is checked on the VoIP Server.
Password Password of the SIP account. The password should be entered if "Enable Register" is checked on the VoIP Server.
From User
All outgoing calls from this SIP Trunk will use the "From User" (in this case the account name for SIP Registration) in From Header of the SIP Invite package. Keep this field blank if not needed.
Online Number
Define the online number that expected by “Skype Connect” and some other SIP service providers. Leave this field blank if not needed.
Dial Pattern Template The account will be allowed to make outbound calls according to the selected template.
Hotline
Enable Hotline
Select whether to use Hotline or not. Hotline is disabled by default. If this feature is enabled, the system will dial out the hotline number automatically after off-hook.
Hotline Number
Set the number to dial out automatically after off-hook.
Delay Dial Define how long to make Hotline take effect after you pick up the phone.
Flash Sets the amount of time, in milliseconds, that a hook flash must remain depressed in
NeoGate TA1600/2400/3200 User Manual
35/63
order for the system to consider it as a valid flash event. Default: 1000ms.
Call Duration Setting
Set up the max cull duration for every call of this user, but it’s only valid for outbound calls. Enter “0” or leave this blank empty, the value would be equal to the max call duration configured in the General Preferences settings page. Note: This setting will not be valid for internal calls.
> Other Settings
Figure 4-3 FXS Port Other Settings
Table 4-2 Description of FXS Port Other Settings
Items Description
Call Waiting
Check this option if the extension should have Call Waiting capability. If this option is checked, the “When busy” follow me options will not be available.
NeoGate TA1600/2400/3200 User Manual
36/63
DND Don’t Disturb. When DND is enabled for an extension, the extension will not be available.
Ring Out Check this option if you want to customize the ring time. Ring tone will stop over the time defined.
Follow me
Call forwarding for an extension can be configured here. You can also configure call forwarding to a hunt group. Prompt: whether the prompt is played or not when the call is transfered. Music On Hold: choose the on hold music.
Volume Settings
Settings for the FXS port volume. Rxgain: adjust receive gain. Txgain: adjust transmit gain.
Caller ID Settings
Select the type of caller ID signaling. FSK and DTMF signal is supported.
Fax If the FXS port is connected to a Fax machine, this option should be checked.
MWI Settings
Message Waiting Indicator (MWI) refers to a special LED on the analog phone, which indicates the voice mail status. There are three lighting methods supported on NeoGate TA gateway: neon, FSK and Polarity. Choose the lighting method according to your phone. NeoGate TA gateway will light the lamp up once receiving a new message; the lamp will goes off if there is no unread voice mail.
Ploarity Settings
A polarity signal is required on some systems for reverse polarity billing. Select if reverse polarity signal is activated on this FXS port. It is not activated by default. Polarity Answer: Whether to send polarity signal while picking up the phone. Polarity Hangup: Whether to send polarity signal while hanging up the phone.
NeoGate TA1600/2400/3200 User Manual
37/63
2) Batch Edit Number of FXS Ports Select the FXS ports, and click the button "Modify Number of the selected Port"
, you can modify the number of the FXS
ports in bulk.
Figure 4-4 Batch Edit Number of FXS Ports
3) Batch Edit FXS Ports You can also modify the selected FXS ports in bulk by clicking the button "Modify
the selected Port" .
Check the options that you want to edit. Options that are not checked and modified will remain the default settings.
Figure 4-5 Batch Edit FXS ports
3) Batch Reset FXS Ports You can reset the selected FXS ports in bulk by clicking the button "Reset the
NeoGate TA1600/2400/3200 User Manual
38/63
selected Port" . The settings for the FXS ports will back
to the default.
4.1.2 Hunt Group
Hunt group is a feature that allows a call reaching multiple FXS ports. The FXS ports will act as a single group, called a hunt group. The number of hunt groups is limited by the number of ports each NeoGate TA model has. For example, there are 24 hunt groups on NeoGate TA2400. Hunt group will be chosen when configuring the FXS port "Follow Me". The hunt group will work when a call reaches the FXS port associated user which is busy or no answer.
Figure 4-6 Hunt Group
NeoGate TA1600/2400/3200 User Manual
39/63
Figure 4-7 Set Hount Group on "FXS Port" Page
There are 3 strategies for hunt group on NeoGate TA.
• Simultaneous
All the FXS users will ring at the same time.
• Circular
In circular hunting, the calls are processed "round-robin". If a call is delivered to FXS port1, the next call will go to 2, the next to 3. The succession throughout each of the FXS users even if one of the previous local users becomes free. When the end of the hunting group is reached, the hunting starts over at the first local users.
• Linear
Linear hunting is also referred to serial hunting. In linear hunting, calls are always delivered to the first FXS users, unless it is busy, then the second, third, and so on.
NeoGate TA1600/2400/3200 User Manual
40/63
4.2 VoIP Settings
To integrate with other IPPBX, we need to configure the VoIP settings in NeoGate TA to set up VoIP trunk (SIP and IAX).
4.2.1 VoIP Server Settings
There are some configurable VoIP(SIP/IAX) Server templates on this page. The number of VoIP Server templates is the half of FXS ports on NeoGate. The VoIP server settings help the FXS ports to register to the VoIP server. Once configured, the templates can be chosen on FXS port setting page. Two modes are available for the VoIP server, we call them VoIP mode and SPS(Service Provider SIP)/SPX(Service Provider IAX) mode. VoIP Mode: The FXS port will be registered as one the VoIP server's SIP extensions if "Enable Register" is checked on VoIP Server template. SPS/SPX Mode: If "Enable Register" is not checked, the FXS port will be registered as a SPS/SPX trunk to the VoIP Server. One SPS/SPX trunk to NeoGate TA also should be created on the VoIP Server.
Figure 4-8 VoIP Server
NeoGate TA1600/2400/3200 User Manual
42/63
> General Table 4-3 Description of VoIP Server General Settings
Items Description Server ID The ID for the VoIP server template. Server Name The name for the VoIP server template. Type Choose the type of the VoIP server, SIP or IAX.
Enabel Register
Do not check "Enable Register", if you want to register the FXS port as a Service Provider SIP (IAX) trunk to the VoIP Server. One Service Provider SIP (IAX) trunk to NeoGate TA also should be created on the VoIP Server. Check "Enable Register" if you want to register the FXS port as an extension of the VoIP server. You will need to enter the relevant user name, password, etc in the FXS port page when using this template.
Transport This will be the transport method used by the SIP Trunk. This method is given by the SIP trunk provider. The options are UDP (default), TCP ,and TLS.
Hostname/IP VoIP server hostname or IP address. 5060 is the standard port number used by SIP protocol. Don’t change this part if it is not required.
Domain VoIP server hostname. An IP address also can be filled here. Enable Outbound Proxy Server
A proxy that receives requests from a client. Even though it may not be the server resolved by the Request-URI.
> Advanced
NeoGate TA1600/2400/3200 User Manual
43/63
Figure 4-10 VoIP Server Advanced Settings
Table 4-4 Description of VoIP Server Advanced Settings Items Description Enable SRTP Define if SRTP is enabled for this VoIP server. Qualify Send check alive packets to the SIP provider.
Caller ID Specify the caller ID to use when making outbound calls over this VoIP server.
Maxmum Channels Control the maximum number of simultaneous calls. Set as 0 to specify no maximum.
Realm Realm is a string to be displayed to users so they know which username and password to use.
Authenticating Incoming Call
When an incoming call reaches TA device and sends INVITE packet to TA, TA responds 401, but the Realm info in 401 Response does not match the Realm set on TA VoIP Server, the provider will refuse to authenticate. If you set this option to No, TA will not reply a 401 Response to the provider to authenticate the incoming call.
DTMF Mode Set default mode for sending DTMF of this trunk. Default setting: rfc2833
Codec Define the codec for this sip trunk and its priority
4.2.2 Dial Pattern Template
Dial pattern template specifying how to route the calls from FXS ports to VoIP server extensions or external numbers. The number of dial pattern templates is limited by the number of ports each NeoGate TA model has.
Figure 4-11 Dial Pattern Template
Table 4-5 Description of Dial Pattern Template Settings
NeoGate TA1600/2400/3200 User Manual
44/63
Items Description Template ID The ID for this template. Template Name A name for this template.
Dial Pattern
Calls from the FXS port should match the dial pattern set on this template, or the call cannot be established. Hover the
pointer over to read tips.
Strip Allows the user to specify the number of digits that will be stripped from the front of the phone number before the call is placed.
Prepend The digits will be appended to the phone number before the call is placed.
DTMF Mode Set default mode for sending DTMF of this trunk. Default setting: rfc2833.
Codec Define the codec for this sip trunk and its priority.
4.2.3 SIP Settings
This is the SIP settings in NeoGate, including General settings, NAT, Codecs, Qos, Response Code, T.38, and advanced settings. 1) General
Figure 4-12 SIP General Settings
NeoGate TA1600/2400/3200 User Manual
45/63
Table 4-6 Description of SIP General Settings Items Description UDP Port Port used for SIP registrations. The default is 5060. Enable Random Port Enable or Disable Random SIP port. Random Port Update Interval
Set the Random Port Update Interval.
TCP Port Port used for SIP registrations. The default is 5060. TLS Port Port used for SIP registrations. The default is 5061.
TLS Verify Server When using NeoGate TA as a TLS client, whether or not to verify server’s certificate. It is “No” by default.
TLS Verify Client When using NeoGate TA as a TLS server, whether or not to verify client’s certificate. It is “No” by default.
TLS Ignore Common Name
Set this parameter as “No”, then common name must be the same with IP or domain name.
TLS Client Method When using NeoGate TA as TLS client, specify the protocol for outbound TLS connections. You can select it as tlsv1, sslv2 or sslv3.
RTP Port Start Beginning of the RTP port range. RTP Port End End of the RTP port range.
DTMF Mode Set the default mode for sending DTMF. Default setting: rfc2833
Max Registration/Subscription Time
Maximum duration (in seconds) of a SIP registration. The default is 3600 seconds.
Min Registration/Subscription Time
Minimum duration (in seconds) of a SIP registration. The default is 60 seconds.
Default Incoming/Outgoing Registration Time
Default Incoming/Outgoing Registration Time: the default duration (in seconds) of incoming/outgoing registration.
Register Attempts The number of SIP REGISTER messages to send to a SIP Registrar before giving up. The default is 0 (no limit).
Register Timeout Number of seconds to wait for a response from a SIP Registrar before classifying the register has timed out. The default is 20 seconds.
Calling Channel Codec Priority
Once enabled, when dialing out via SIP/SPS trunks, the codec of calling channel will be selected preferentially. If not, NeoGate TA will follow the priority order in your SIP/SPS trunks.
Video Support Support SIP video or no. The default is yes.
Max Bit Rate Configure the max bit rate for video stream. The default: 384kb/s.
NeoGate TA1600/2400/3200 User Manual
46/63
DNS SRV Look Up Please enable this option when your SIP trunk contains more than one IP address.
User Agent To change the user agent parameter of asterisk, the default is “NeoGate TA”; you can change it if needed.
2) NAT
Figure 4-13 NAT Settings
Table 4-7 Description of SIP General Settings
Items Description
Enable STUN STUN (Simple Traversal of UDP through NATs) is a protocol for assisting devices behind a NAT firewall or router with their packet routing.
STUN Address
The STUN server allows clients to find out their public address, the type of NAT they are behind and the internet side port associated by the NAT with a particular local port. This information is used to set up UDP communication between the client and the VOIP provider and so establish a call.
External IP Address
The IP address that will be associated with outbound SIP messages if the system is in a NAT environment.
External Host
Alternatively you can specify an external host, and the system will perform DNS queries periodically. This setting is only required when your public IP address is not static. It is recommended that a static public IP address is used with this system. Please contact your ISP for more information.
External Refresh Interval
Used to identify the local network using a network number/subnet mask pair when the system is behind a NAT or firewall. Some examples of this are as follows: “192.168.0.0/255.255.0.0”: All RFC 1918 addresses are local networks; “10.0.0.0/255.0.0.0”: Also RFC1918;
NeoGate TA1600/2400/3200 User Manual
47/63
“172.16.0.0/12”:Another RFC1918 with CIDR notation; “169.254.0.0/255.255.0.0”: Zero conf local network. Please refer to RFC1918 for more information.
NAT Mode
Global NAT configuration for the system; the options for this setting are as follows: Yes = Use NAT. Ignore address information in the SIP/SDP headers and reply to the sender's IP address/port. No = Use NAT mode only according to RFC3581. Never = Never attempt NAT mode or RFC3581 support. Route = Use NAT but do not include rport in headers.
Allow RTP Reinvite
By default, the system will route media steams from SIP endpoints through itself. Enabling this option causes the system to attempt to negotiate the endpoints to route packets to each other directly, bypassing the system. It is not always possible for the system to negotiate endpoint-to-endpoint media routing.
3) Codecs We can choose the allowed codec in NeoGate TA, a codec is a compression or decompression algorithm that used in the transmission of voice packets over a network or the Internet. For more information about codec, you can refer to this page: http://en.wikipedia.org/wiki/List_of_codecs
Figure 4-14 Codecs
If you want to use codec G729, we recommend buying a license key and input it here. 4) Qos QoS (Quality of Service) is a major issue in VoIP implementations. The issue is how to guarantee that packet traffic for a voice or other media connection will not be delayed or dropped due interference from other lower priority traffic. When the network capacity is insufficient, QoS could provide priority to users by setting the value.
NeoGate TA1600/2400/3200 User Manual
48/63
Figure 4-15 Qos
Note: It’s recommended that you configure the QoS in your router or switch instead of NeoGate side. 5) Response Code You can change the response code on NeoGate TA to the one you want before sending it to the VoIP server. It helps the VoIP server understands better the exact call status, like busy, no response and others.
Figure 4-16 Response Code
Note: We don’t’ recommend configuing this if you are not familiar with the code of call status from the VoIP server. 6) T.38 Settings on this page is for the purpose of improving receiving and sending T.38 FAX.
Figure 4-17 T.38 Settings
Table 4-8 Description of T.38 Settings
Items Description Re-invite SDP Not Add T.38 If set to Yes, SDP in re-invite packet will not add
NeoGate TA1600/2400/3200 User Manual
49/63
Attributes T.38 attributes. Error Correction Re-invite SDP T38FaxUdpEc. T.38 Max Bit Rate Set T38 Max Bit Rate. 7) Advanced Settings
Figure 4-18 SIP Advanced Settings
Table 4-9 Description of SIP Advanced Settings Items Description From Field Where to get the caller ID in SIP packet. To Field Where to get the DID in SIP packet.
180 Ringing It is set when the telecom provider needs. Usually it is not needed.
Remote Party ID Whether to send Remote-Party-ID on SIP header or not. Default: no.
Allow Guest
Whether to allow anonymous registration extension or not. Default: no. It’s recommended that it is disabled for security reason.
Pedantic Enable pedantic parameter. Default: no.
Alwaysauthreject
If enabled, when NeoGate TA rejects “Register” or “Invite” packets, NeoGate TA always respond the packets using “SIP404 NOT FOUND”. It’s recommended that it is enabled for security reason.
Session-timers Enable session-timer mode, default: yes. If you find the call is cut off every 15 minutes every time, please disable this.
Session-expires The max refresh interval
Session-minse The min refresh interval, which mustn't be shorter than 90s.
Session-refresher Choose the session-refresher, the default is
NeoGate TA1600/2400/3200 User Manual
50/63
Uas.
4.2.4 IAX Settings
IAX is the Internal Asterisk Exchange protocol, you can connect to NeoGate TA or register IAX trunk to another IAX server. It’s supported by the asterisk-based IPPBX.
Figure 4-19 IAX Settings
Table 4-10 Description of IAX Settings Items Description Bind Port Port used for IAX2 registrations. Default is 4569.
Bandwidth Low/medium/high with this option you can control which codec to be used.
Min Registration Time Minimum duration (in seconds) of an IAX2 registration. Default is 60 seconds
Max Registration Time Maximum duration (in seconds) of an IAX2 registration. Default is 1200 seconds.
Codecs Enable the codec you want for IAX communication.
NeoGate TA1600/2400/3200 User Manual
51/63
4.3 Gateway Settings
4.3.1 General Preferences
Figure 4-20 General Settings
Table 4-11 Description of General Settings
Items Description
Ring Timeout Number of seconds to ring a device before executing the "Follow me" configurations. This is a gloable setting for all FXS ports.
MAX Call Duration The absolute maximum amount of time permitted for a call. A setting of 0 disables the timeout.
Music On Hold Set hold music for the system.
Key As Send Set the "#" or "*" to perform as a send key while dialing. Default is "#".
Enable Jitterbuffer Forces the use of a jitter buffer on the received side of a SIP channel. The call quality will be improved if this option is enabled.
Jitterbuffer MaxSize Max length of the jitter buffer. Default is 40 milliseconds
4.3.2 Feature Codes
There are various feature codes on NeoGate TA. The feature codes are used to acquire the gateway info or activate and inactivate supplementary services. The default feature codes are illustrated below. The parameters for feature codes are configurable.
NeoGate TA1600/2400/3200 User Manual
52/63
Figure 4-21 Feature codecs
> General Table 4-12 Description of General Settings
Items Default Description
Internal Call Prefix
*99
Dial the feature code and the FXS port number when making calls between the analog phones connected to multiple ports of the NeoGate TA without the use of a VoIP server.
Speed Dial Prefix *98 The prefix number for applying a speed dialing. The prefix should be added ahead of the speed dial number.
Attended Transfer
*3 Users may transfer an incoming call by dialing *3 on their phone.
Blind Transfer *03 Users may blind transfer an incoming call by dialing*03 on their phone.
Direct IP Calling *96
Direct IP calling allows two parties, that is, a FXS Port with an analog phone and another VoIP Device, to talk to each other in an ad hoc fashion without a SIP proxy. The default "Direct IP Calling" feature code is *96.
Check Number *97 Users can check the analog phone's number by simply dialing the "Check Number" feature code on the phone. The default "Check Number" feature code is *97.
Voice Menu *** Users may enter the voice prompt menu by pressing *** on their phone.
Voice Menu Password Settings
123456 The password of voice menu is required before entering the advanced settings. The default password is 123456.
NeoGate TA1600/2400/3200 User Manual
53/63
> Call Forwarding Preferences
Table 4-13 Description of Call Forwarding Preferences Items Default Description
Reset to Defaults *70 Users may reset all call forwarding defaults by calling *70 on their phone.
Enabel Forward All Calls *71 Users may enable always forward by calling *71 on their phone.
Disable Forward All Calls *071 Users may disable always forward by calling *071 on their phone.
Enable Forward When Busy *72 Users may enable busy forward by dialing *72 on their phone.
Disable Forward When Busy *072 Users may disable busy forward by calling *072 on their phone.
Enable Forward No Answer *73 Users may enable no answer forward by calling *73 on their phone.
Disable Forward No Answer *073 Users may disable no answer forward by calling *073 on their phone.
Forward to Internal Port *74 Users may activate call forwarding to port by dialing this feature code, followed by the FXS port number.
Forward to Number *75
Users may activate call forwarding by dialing this feature code, followed by the extension or phone number to forward all calls to this number. Note: Users may activate Forward to number by dialing *74 + phone number. E.g. by dialing *74501, all calls will be forwarded to extension 501.
Forward to Hunt Group *76 Users may forward the call to a hunt group by calling *75 on their phone.
Enable Do Not Disturb *77 Activate "Do Not Disturb". Once activated, the FXS port will reject all incoming calls.
Disable Do Not Disturb *077
Disable "Do Not Disturb" for the FXS port by pressing the feature code on the phone. It will recover normal ringing upon the arrival of incoming calls.
NeoGate TA1600/2400/3200 User Manual
54/63
4.3.3 Speed Dial Settings
There are 128 configurable Speed Dial templates available on NeoGate TA.
Figure 4-22 Speed Dial
·Source Number The speed dial number. ·Destination Number The number you want to call. E.g. the source number is “1”. The destination number is 93788444. The prefix number is *98. You can use an extension with any type to dial *981, then it will call the number 93788444. Note: Don’t forget to add the dial pattern according to the selected dial pattern template.
4.4 Audio Settings
4.4.1 Custom Prompts
We can upload the prompts in this page; you can also download it and save it as a backup.
Figure 4-23 Custom Prompts
NeoGate TA1600/2400/3200 User Manual
55/63
The administrator can upload prompts by doing the following: 1) Click “Upload Prompt”. 2) Click “Browse” to choose the desired prompt. 3) Click “Upload” to upload the selected prompt.
Figure 4-24 Upload A Prompt
Note: The file size must not be larger than 1.8 MB, and the file must be WAV format: GSM 6.10 8 kHz, Mono, 1 Kb/s; Alaw/Ulaw 8 kHz, Mono, 1 Kb/s; PCM 8 kHz, Mono, 16 Kb/s.
4.4.2 Music on Hold Prompts
In this page, we can upload the music on hold prompts.
Figure 4-25 Music On Hold
The administrator can upload on hold music as follows: 1) Click “Upload Music on Prompt”. 2) Click “Browse” to choose the desired audio file. 3) Click “Upload” to upload the selected file.
NeoGate TA1600/2400/3200 User Manual
56/63
Figure 4-26 Upload Music on Hold Prompt
Note: The file size must not be larger than 1.8 MB, and the file must be WAV format: GSM 6.10 8 kHz, Mono, 1 Kb/s; Alaw/Ulaw 8 kHz, Mono, 1 Kb/s; PCM 8 kHz, Mono, 16 Kb/s.
4.4.3 System Prompts Settings
There are multilingual system prompts on NeoGate TA. You can download the appropriate language you need. NeoGate TA can support American English, Australian English, Chinese, Dutch, French, Canadian French, German, Greek, Hungarian, Italian, Polish, Portuguese, Brazilian Portuguese, Russian, Spanish, Mexican Spanish, Turkish, Thai, and Korean currently. Notes: 1. Auto-detection is highly recommended. But if you prefer to download via
HTTP or TFTP server, please contact the local dealer for the prompts. 2. When update successfully, just click “Apply Changes” on Web then it will take
effect, there is no need to reboot.
Figure 4-27 System Prompts Settings Page
NeoGate TA1600/2400/3200 User Manual
57/63
4.5 Advanced Settings
4.5.1 Tone Zone Settings
Advanced ring tones for all the FXS ports can be configured on this page. There are pre-grogrammed tone zone settings for some countries and regions. Users can simply find and select thier country to get tone zone settings for the gateway.
Figure 4-28 Tone Zone Settings
Users may also configure the tone zone according to the national standard by selecting "User custom for Tone Zone". Please refer to the document below and configure the tone zone settings on NeoGate TA: http://www.itu.int/ITU-T/inr/forms/files/tones-0203.pdf
Figure 4-29 Customize Tones
Table 4-14 Description of Tone Zone Settings
Items Description
Country Choose the country to get pre-programmed tone zone settings or choose "User custom for Tone Zone" to configure the settings manually.
Ring Cadence Configuration option for all FXS ports ring cadence for all incoming calls.
NeoGate TA1600/2400/3200 User Manual
58/63
Dial Tone Prompt tone of off-hook dial tone. Ringback Tone The tone sent to caller when ringing is on. Busy Tone Used for busy line prompt. Call-Waiting Tone Used for notification in call waiting.
Congestion Tone Used to indicate that an invalid code has been dialed, or that all circuits (trunks) are busy and/or the call is unroutable.
2nd Dial Tone Used for the second stage dial tone.
NeoGate TA1600/2400/3200 User Manual
59/63
4.5.2 RADIUS Settings
NeoGate TA supports RADIUS (Remote Authentication Dial In User Service) protocol. RADIUS feature is mainly for billing purpose on NeoGate TA. There are primary and secondary RADIUS server configurations available. Once the primary server is unreachale, the RADIUS requests will be sent to the secondary server.
Figure 4-30
Table 4-15 Description of RADIUS Settings
Items Description Enable RADIUS Enable RADIUS on NeoGate TA. Primary Server IP Set IP address of the primary server.
Primary Server Port Default is 1813. Specifies the port to be used for the primary RADIUS account.
Primary Server Key Specifies the key to be used to authenticate the RADIUS connection to the Primary server. The key is set according to the RADIUS server.
Secondry Server IP Set IP address of the primary server. The second sever will be activated the primary one becomes unusable.
Secondry Server Port Default is 1813. Specifies the port to be used for the second RADIUS account.
Secondry Server Key Specifies the key to be used to authenticate the RADIUS connection to the second server. The key is set according to the RADIUS server.
RADIUS Timeout
Specifies the number of seconds to wait for a response after the RADIUS message is sent to the server. Default: 10 seconds. The retransmission will be performed if there is no response after the timeout.
RADIUS Retry Times Specifies the number of times the RADIUS messages will
NeoGate TA1600/2400/3200 User Manual
60/63
send to the RADIUS server before giving up. Default: 3. Call Out CDR Whether to send "Call Out CDR" to RADIUS server or not. Call In CDR Whether to send "Call In CDR" to RADIUS server or not. No Answer CDR Whether to send "Call Out CDR" to RADIUS server or not.
Part II. Basic Operations Here are instructions about how to operate on analog phones connected to NeoGate TA to use some features.
1. NeoGate TA Voice Menu
NeoGate TA provides a voice menu to guide you to configure the network settings for the device. You need to press *** on the analog phone which is connected to NeoGate TA’s FXS port to enter the voice menu. The default password to enter “Advanced Settings” is 123456. You can change the password on NeoGate TA Web page.(Gateway→Gateway Settings→Feature Codes→Voice Menu Password Settings)
Tips: 1. “9” listen to the prompt again. 2. “*” returns to the last menu.
NeoGate TA1600/2400/3200 User Manual
61/63
2. Inter-port Call
NeoGate TA supports inter-port calls between the phones which are connected to FXS ports of NeoGate TA. Achieve it by simply pressing the "Internal Call Extra" feature code (default *99) + the FXS port number on the phone. Note: You need add digit 0 before the FXS port number if the port number is between 1 and 9. For example, to make a call from the phone which is connected to NeoGate TA FXS port 1 to another phone which is connected to FXS port2, you need to dial *9902 on the phone. The user connected to port 16 can be reached by dialing *9916 on the phone.
3. Call Hold
An active call can be held by pressing "flash" key on the analog phone. Press the key again to resume the call. If there is no "flash" key on the phone, you can use "hook flash" (quickly toggle on-off hook) to hold a call. The call may be disconnected by chance if using "hook flash".
4. Call Waiting
If the call waiting is activated for the FXS port, the FXS user who is in a call can hear a call waiting tone "beep" when there is a new incoming call. The user can press "hook flash" to toggle between the active call and the incoming call.
Figure 1-1 Enable "Call Waiting" on FXS Port Page
NeoGate TA1600/2400/3200 User Manual
62/63
5. Call Transfer
Blind transfer and attended transfer are supported on NeoGate TA. Users can achieve call transfer by pressing the feature code during the call. Blind Transfer Default feature code: *03 1. Dial "*03" during the call; 2. Dial the called number after hearing a prompt "transfer"; 3. The call will be transferred after the number is dialed. Attended Transfer Default feature code: *3 1. Dial "*3" during the call; 2. Dial the called number after hearing a prompt "transfer"; 3. Talk to the transfer recipient; 4. The call will be transferred after hanging up.
6. Three-party Conference Users can make a three-party conference call on NeoGate TA. Assuming that A and B are in the call and B wants to invite C to a conference. Please check the following steps of how to establish a conference. 1. B presses "flash" key or taps hook flash to get a dial tone; A will hear the on hold music meanwhile; 2. B dials C's number; 3. If C answers the call, then B presses "flash" key or tap hook flash, the conference will be established, including A, B, and C. 4. If there is no answer on C, A can press "flash" key or tap hook flash to resume the call with A. 5. C will be ejected if B presses "flash" key or taps flash hook during the conference call.
7. Direct IP Call
Direct IP call allows two parties, that is, a FXS Port with an analog phone and another VoIP Device, to talk to each other in an ad hoc fashion without a SIP proxy. The default "Direct IP Calling" feature code is *96. Example: Target IP address: 192.168.2.123 Destination port:5060 To call the IP phone, you should dial *96192*168*2*123*5060 on the analog
NeoGate TA1600/2400/3200 User Manual
63/63
phone.
8. Change NeoGate TA’s IP Address Using
Analog Phones
By default, NeoGate TA obtain a dynamic IP address from the DHCP server. You can change the device’s IP address via the analog phone which is connected to the FXS port. There are 3 modes supported on NeoGate TA access the internet. ● DHCP ● Static IP Address ● PPPoE Here we introduce how to set a static IP address for NeoGate TA. IP address: 192.168.10.125 Subnet mask: 255.255.255.0 Gateway: 192.168.10.1 DNS: 8.8.8.8 1. Press *** to enter the voice menu. 2. Press 3 to enter the “Advanced Settings”. 3. Enter the password follow by the pound key: 123456# (The default
password is 123456). 4. Press 2 to change the IP address. 5. Press 2 to enable the static IP. 6. Press 1 to change the IP address and follow by the new IP address
(1192*168*10*125). 7. Press 2 to change the subnet mask and follow by the new subnet mask
(2255*255*255*0). 8. Press 3 to change the gateway and follow by the new gateway
(3192*168*10*1). 9. Press 4 to change the dns and follow by the new dns (48*8*8*8). 10. Press 5 to reboot the device. 11. After reboot, you can access the device by the new IP address.
[End]