New Features Trimble GCS & Cat AccuGrade. Common New Features in V11.30/12.00

New FeaturesTrimble GCS & Cat AccuGrade

Common New Features in V11.30/12.00

Common New Features in V11.30/12.00

Background TCC Sync Auto TCC Sync Location RTK Configure SNR450 over CAN MS972 Support VRS NTRIP Client Mapping UI Changes Recent Names and Codes List for Point Mapping VM430 Support Languages

Background TCC Sync

Previous version forced you to stop guidance while you synchronized to the Connected Community

Now you can start a TCC sync & continue to work

Background TCC Sync

Always “On” Start the Sync either manually or

automatically and exit the screen to keep working

Return to the screen anytime to view progress

Auto TCC Sync

Lets you keep office & machine data up to date– without manually initiating a TCC Sync

TCC synchronization is performed:– when a new tag file is created (every 5 minutes) – or every 60 minutes, whichever comes first

Auto TCC Sync

Press the softkey to toggle between Auto & Manual Sync

Auto TCC Sync

Manual Sync is useful to minimise Cell Phone data– When you have Wi-Fi as well– Only sync data when in Wi-Fi coverage

Use cell for VRS corrections everywhere

Location RTK

– Location RTK GNSS Receivers offer a lower cost solution for machines that don’t need high accuracy

– Location RTK with Precise Horizontal– Opposite of Trimble Site Positioning Systems

• V11.30/12.00 adds support for receiver 1-10 Location RTK– 1 cm Horizontal

• Full accuracy

– 10 cm Vertical – For Cab mount machines systems only

10 cm

10 cm

1 cm 1 cm

x

Location RTK

Best for Compactors– Need accurate Horizontal positions– Also some rough grading machines, such large

dozers, scrapers– So coverage mapping is good– But only when not using vertical information

Location RTK

System diagnostics reports the functionality level of the GPS Receiver – So users can easily see if the system is using a full

RTK or L-RTK receiver for troubleshooting

10 cm

10 cm

1 cm 1 cm

x

Configure SNR410 over CAN

Should be transparent to users Used to be done on the serial line Now done on CAN Allows serial line to be used for

other communications if required

MS972 GNSS Smart Antenna

System recognizes MS972

Allows them to be used on compactor cab-mount install only

MS972 GNSS Smart Antenna

Will show up as “Invalid Sensor” in diagnostics if not allowed

VRS NTRIP Client

V11.30/12.00 adds VRS NTRIP Client v2.0 – The Control Box itself, can be configured to

receive VRS corrections & not the modem

SNM940 can be used for TCC and VRS/Remote Base corrections

This adds value as it does not force users to have 2 cell phone modems & 2 service plans on the 1 machine

VRS / Remote Base

In V11.2x the SNM930 had to be configured by a PC to receive the Remote Base corrections– This modem was dedicated to Remote Base

support & had to have a dedicated RS232 line– Problem was in V11.21 you had to have 2 SNM930s

if you wanted VRS Corrections and TCC support

VRS / Remote Base

In version 11.3 only - SNM930 can now be configured over the CB430

• Only ONE SNM940 required for BOTH VRS Corrections and TCC support

Mapping UI changes

Major changes over last version Now map multiple different types at once Display whichever you want

Mapping UI changes

Mapping UI changes

Excellent for Compaction – Map Pass Count & CMV & CMV Change & Cut/Fill

All at once

Mapping UI changes

Mapping UI changes

Can now Record Points while Mapping– Very useful to operators– Especially in the Excavator– Press and Hold to Record Point while mapping

Main Screen Views

Main Screen Views

Yes or No

Main Screen Views

Yes or No

Main Screen Views

None, Points only, Points and Names

Main Screen Views

If Mapping for the main screen views is No– Then NO Map Active Views are available

Main Screen Views

If Mapping for the main screen views is Yes– Then Map Active Views ARE available

Main Screen Views

“Active views” are all Yes or No– Note the line of explanatory text

Main Screen Views

“Active views” are all Yes or No– Note the line of explanatory text

Main Screen Views

Ripper mapping has changed Now “No” (Off) by default Obeys the same rules as other mapping types

Main Screen Views

Compactor has different “Active views”– Add CMV and CMV Change– Lose Ripper

Main Screen Views

Softkey F5 is configurable– None, Mapping: On/Off/Auto, Reset Maps, Record

Point

Main Screen Views

Softkey F5 Press and Hold is also configurable– None, Record Point

Main Screen Views

Compactor has both Softkeys F4 &F5 configurable– None, Mapping: On/Off/Auto, Reset Maps, Record

Point, In Field Report

• Mapping: On/Off/Autoalso has Press & Hold for Record Point

Main Screen Views

When Compactor is Not mapping softkey F4 becomes Vertical Offset

Mapping/Recording

Different screens for:

Compactor and non-compactor

Mapping/Recording Settings

In Manager Mode only by default


Yes or No


No, Yes, Yes when mapping Yes when mapping - *NEW*

• Only creates TAG files when Auto Mapping conditions are met


Yes or No


Yes or No




Yes or No


For Compactors None, All maps, CMV, CMV and Pass Count


For other machines Always, Driving forward, Automatic on, Auto +

forward

Main Screen Views

• Plan Views– Rotation and Auto Pan are set here– Rotation is now available on excavators

• Active Views– Terrain, Cut/Fill, Pass Cont , CMV, CMV Change,

Ripper, Radio Coverage, Plan View, Cross section, Profile, Text1, Text2

• Mapping Softkeys– None, Mapping: On/Off, Reset Maps, Record

Points, In-Field Report

Mapping UI changes

Recent Name & Code List for Point Mapping Now select from a list of recently used point

names and/or codes

• Previously you had to re-enter the point name or code

Mapping UI changes

Recent Point Code List

VM430

• New Valve Module to replace both VM410 & VM420

– Works in all AGCS systems – old & new– Adapter cables required on old harnesses

AND/OR old displays– New cables to valves– Only one for Grader Lift, Lift, Sideshift

• Used to require 2 VM420s

Languages

All supported languages are in the first release of software

Documentation is only available in English on release

Languages

Questions

?

Documents

New Features Trimble GCS & Cat AccuGrade. Common New Features in V11.30/12.00