40
NEW GENERATION INTERNATIONAL DESIGN GUIDE

NEW GENERATION INTERNATIONAL DESIGN GUIDE - Sub-Zero & Wolfnewgeneration.subzero-wolf.com/Content/WolfDG_INTL_EN.pdf · 39 Wolf Warranty. wolfappliance.com | 3 M Series Ovens Three

  • Upload
    buinhan

  • View
    216

  • Download
    0

Embed Size (px)

Citation preview

NEW GENERATIONINTERNATIONAL DESIGN GUIDE

2 | English

Features and specifications are subject to change at any time without notice. Visit wolfappliance.com/specs for the most up-to-date information.

IMPORTANT NOTE: Throughout this guide, dimensions may vary by ± 3 mm.

Contents

3 M Series Ovens

12 E Series Ovens

19 Convection Steam Ovens

24 Gas Cooktops

28 Coffee Systems

33 Downdraft Systems

39 Wolf Warranty

wolfappliance.com | 3

M Series Ovens

Three striking new looks are just the beginning. Superior performance features include an even more advanced dual vertical convection fan system, touch-screen controls, convenient new preset cooking programs, improved interior lighting, and even redesigned hinges. There is more usable space inside for deliciousness on a grand scale.

KEY FEATURES

• Dual VertiCross™ convection system supplies two corner column fans for best heat saturation and distribution.

• Nine cooking modes, including the bake stone and dehydration kits for precise, easy-to-use control.

• Self-cleaning ovens.

• Full-extension racks allow easy access to foods.

• Spring and damper door hinge system for smooth opening and closing of the door.

WOLF M SERIES OVENS

UPPER OVEN LOWER OVEN

M SERIES OVENS

TRANSITIONAL

ICBSO30PM/S/PH

ICBSO30CM/B

ICBSO30TM/S/TH

ICBDO30PM/S/PH

ICBDO27TM/S/TH

ICBDO30CM/B

ICBSO36TM/S/TH

ICBSO27TM/S/TH

ICBDO30TM/S/TH

PROFESSIONAL

CONTEMPORARY

4 | English

WOLF M SERIES OVENS

M Series Ovens

TRANSITIONAL SINGLE OVEN

TRANSITIONAL DOUBLE OVEN

OPEN OVEN DOOR584 mm

BEHIND FRAME

723mm

686mm

65mm

46 mm

543mm

WWIDTH

22mm

36 mmCONDUITCHANNEL

218mm

51mm

WIDTH

TRANSITIONAL W

686 mm Model 683 mm762 mm Model 759 mm914 mm Model (single oven only) 911 mm

OPEN OVEN DOOR

584 mmBEHIND FRAME

1291mm

1254mm

65mm

46 mm

543mm

WWIDTH

22mm

36 mmCONDUITCHANNEL

218mm

51mm

SPECIFICATIONS

INTERIOR CAPACITY L

686 mm Oven 127762 mm Oven 144914 mm Oven 178

INTERIOR DIMENSIONS W H D

686 mm Oven 565 mm 445 mm 505 mm762 mm Oven 641 mm 445 mm 505 mm914 mm Oven 794 mm 445 mm 505 mm

AHAM overall volume.

wolfappliance.com | 5

WOLF M SERIES OVENS

M Series Ovens

PROFESSIONAL SINGLE OVEN

OPEN OVEN DOOR584 mm

BEHIND FRAME

723mm

686mm

83mm

46 mm

543mm

22mm

36 mmCONDUITCHANNEL

218mm

51mm

759 mm

OPEN OVEN DOOR

584 mmBEHIND FRAME

1291mm

1254mm

759 mm

46 mm

543mm

83mm

22mm

36 mmCONDUITCHANNEL

218mm

51mm

UPPER OVEN LOWER OVEN

PROFESSIONAL DOUBLE OVEN

WIDTH

PROFESSIONAL W

762 mm Model 759 mm

SPECIFICATIONS

INTERIOR CAPACITY L

762 mm Oven 144

INTERIOR DIMENSIONS W H D

762 mm Oven 641 mm 445 mm 505 mm

AHAM overall volume.

6 | English

WOLF M SERIES OVENS

OPEN OVEN DOOR

584 mmBEHIND FRAME

1291mm

1254mm

46 mm

543mm

25mm

36 mmCONDUITCHANNEL

218mm

51mm

759 mm

OPEN OVEN DOOR584 mm

BEHIND FRAME

723mm

686mm

46 mm

543mm

25mm

36 mmCONDUITCHANNEL

218mm

51mm

759 mm

M Series Ovens

CONTEMPORARY SINGLE OVEN

CONTEMPORARY DOUBLE OVEN

WIDTH

CONTEMPORARY W

762 mm Model 759 mm

OVEN SPECIFICATIONS

INTERIOR CAPACITY L

762 mm Oven 144

INTERIOR DIMENSIONS W H D

762 mm Oven 641 mm 445 mm 505 mm

AHAM overall volume.

wolfappliance.com | 7

WOLF M SERIES OVENS

Planning Information

The oven can be installed in a standard or flush inset application. If a cooktop is being installed above an oven, a minimum of 6 mm is required between units. Location of the electrical supply within the oven opening may require additional cabinet depth. Refer to the chart below.

Finish the edges of the opening. They may be visible when the door is open.

For flush inset installations, a minimum 3 mm reveal is required on all sides. To ensure consistent 3 mm reveals, each corner of the opening must be exactly 90°.

INSTALLATION REQUIREMENTS

BASE SUPPORT

Single Oven 115 kgDouble Oven 181 kg

TRIM OVERLAP

Top 25 mmBottom 0 mmSides 18 mm

ELECTRICAL

Installation must comply with all applicable electrical codes and be properly grounded (earthed).

Locate the electrical supply flush with the back wall and within the shaded area shown in the illustration for your spe-cific installation on the following pages. For ease of instal-lation, the electrical supply for the oven can be placed in an adjacent cabinet within reach of the conduit.

Performance may be compromised if the electrical supply is less than 220 volts.

The oven is supplied with a single phase and 3-phase convertible power inlet box. The wiring diagram covering the control circuit is provided with the oven.

ELECTRICAL REQUIREMENTS

SINGLE OVEN SINGLE PHASE 3-PHASE

Required Power Supply 220-240 V AC 50/60 Hz

380-415 V AC 50 Hz

Maximum Connected Load 5.4 kW TBDTotal Amps 22 TBD

DOUBLE OVEN SINGLE PHASE 3-PHASE

Required Power Supply 220-240 V AC 50/60 Hz

380-415 V AC 50 Hz

Maximum Connected Load 10.8 kW TBDTotal Amps 45 TBD

8 | English

WOLF M SERIES OVENS

M Series Single Oven

STANDARD INSTALLATION

E

FRONT VIEWSIDE VIEW

NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.

699 mmOPENINGHEIGHT

121 mmTYPICAL

591 mmOPENING

DEPTH

WOPENING WIDTH

TOP VIEW

E127mm

102mm

OPENING WIDTH

MODEL W

686 mm Model 648 mm762 mm Model 724 mm914 mm Model 876 mm

wolfappliance.com | 9

WOLF M SERIES OVENS

M Series Double Oven

STANDARD INSTALLATION

E

FRONT VIEWSIDE VIEW

NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.

1267 mmOPENINGHEIGHT

591 mmOPENING

DEPTH

WOPENING WIDTH

432 mmTYPICAL

TOP VIEW

E

E127mm

102mm

E

OPENING WIDTH

MODEL W

686 mm Model 648 mm762 mm Model 724 mm

10 | English

WOLF M SERIES OVENS

M Series Single Oven

FLUSH INSET INSTALLATION

E

FRONT VIEWSIDE VIEW

*25 mm minimum depth. Shaded areas will be visible and should be finished to match cabinetry.**22 mm for professional and transitional models and 25 mm for contemporary model.

NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.

730 mmFLUSH INSET

HEIGHT

29 mm

3 mm

21 mm

610 mmFLUSH INSET

DEPTH

22 mmOR

25 mm**FINISHEDCLEATS*

WFLUSH INSET WIDTH

TOP VIEW

E

E127mm

102mm

FLUSH INSET WIDTH

MODEL W

686 mm Model 689 mm762 mm Model 765 mm914 mm Model 918 mm

wolfappliance.com | 11

WOLF M SERIES OVENS

M Series Double Oven

FLUSH INSET INSTALLATION

E

FRONT VIEWSIDE VIEW

*25 mm minimum depth. Shaded areas will be visible and should be finished to match cabinetry.**22 mm for professional and transitional models and 25 mm for contemporary model.

NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.

1299 mmFLUSH INSET

HEIGHT

29 mm

3 mm

21 mm

610 mmFLUSH INSET

DEPTH

22 mmOR

25 mm**FINISHEDCLEATS*

WFLUSH INSET WIDTH

432 mmTYPICAL

TOP VIEW

E

E127mm

102mm

FLUSH INSET WIDTH

MODEL W

686 mm Model 689 mm762 mm Model 765 mm

12 | English

E Series Ovens

Stainless models now feature a redesigned stainless steel touch-action control panel, helping to create great meals with ease, as well as adding a striking design feature to the kitchen. Smart technology gives the E series ten cooking modes, with Wolf’s innovative dual convection in single ovens and in the upper unit of double ovens. E series ovens can be installed flush with cabinets for a contemporary, integrated look. Wolf E series ovens are crafted of stainless steel. Tubular oven handles have been updated to match the rest of the new Wolf cooking appliance offering, providing a more cohesive family look.

KEY FEATURES

• NEW! Redesigned stainless steel touch control panel.

• Dual convection—two fans for even heat distribution.

• Ten cooking modes, including the bake stone and dehydration kits for precise, easy-to-use control.

• Self-cleaning ovens.

• Full-extension bottom rack for easier access to foods.

• Balanced door hinge system for smooth opening and closing of the door.

ICBSO30CE/B/TH

ICBSO30TE/S/TH

ICBDO30TE/S/TH

ICBDO30CE/B/TH

ICBSO30PE/S/PH

ICBDO30PE/S/PH

WOLF E SERIES OVENS

E SERIES OVENS

TRANSITIONAL

PROFESSIONAL

CONTEMPORARY

wolfappliance.com | 13

E Series Ovens

SINGLE OVEN

DOUBLE OVEN

603 mmBEHIND FRAME

708mm

759 mm

CONDUITCHANNEL 689

mm

73mm

*25 mm for professional and transitional models and 32 mm for contemporary model.

76 mm

718 mm

559mm

244mm

225mm

25 mm OR32 mm*

OPEN OVEN DOOR

603 mmBEHIND FRAME

1280mm

1261mm

759 mm 73mm

CONDUITCHANNEL

718 mm

559mm

244mm

225mm

76 mm

*25 mm for professional and transitional models and 32 mm for contemporary model.

OPEN OVEN DOOR

25 mm OR32 mm*

SPECIFICATIONS

INTERIOR CAPACITY L

762 mm Oven 127

INTERIOR DIMENSIONS W H D

762 mm Oven 635 mm 419 mm 483 mm

AHAM overall volume.

WOLF E SERIES OVENS

WIDTH

E SERIES W

762 mm Model 759 mm

14 | English

Planning Information

The oven can be installed in a standard or flush inset application. If a cooktop is being installed above an oven, a minimum of 6 mm is required between units. Location of the electrical supply within the oven opening may require additional cabinet depth. Refer to the chart below.

Finish the edges of the opening. They may be visible when the door is open.

For flush inset installations, a minimum 6 mm reveal is required on all sides. To ensure consistent 6 mm reveals, each corner of the opening must be exactly 90°.

INSTALLATION REQUIREMENTS

BASE SUPPORT

Single Oven 115 kgDouble Oven 181 kg

TRIM OVERLAP

Top 13 mmBottom 3 mmSides 17 mm

ELECTRICAL

Installation must comply with all applicable electrical codes and be properly grounded (earthed).

Locate the electrical supply flush with the back wall and within the shaded area shown in the illustration for your spe-cific installation on the following pages. For ease of instal-lation, the electrical supply for the oven can be placed in an adjacent cabinet within reach of the conduit. Unit is supplied with terminal box convertible to single or 3-phase.

The wiring diagram covering the control circuit is provided with the oven.

ELECTRICAL REQUIREMENTS

SINGLE OVEN SINGLE PHASE 3-PHASE

Required Power Supply 220-240 V AC 50/60 Hz

380-415 V AC 50 Hz

Maximum Connected Load 4.4 kW 4.4 kWTotal Amps 19 19

DOUBLE OVEN SINGLE PHASE 3-PHASE

Required Power Supply 220-240 V AC 50/60 Hz

380-415 V AC 50 Hz

Maximum Connected Load 7.4 kW 5.1 kWTotal Amps 32 22

WOLF E SERIES OVENS

wolfappliance.com | 15

WOLF E SERIES OVENS

E Series Single Oven

STANDARD INSTALLATION

E

FRONT VIEWSIDE VIEW

NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.

692 mmOPENINGHEIGHT

610 mmOPENING

DEPTH

724 mmOPENING WIDTH

121 mmTYPICAL

TOP VIEW

E127mm

102mm

16 | English

E

FRONT VIEWSIDE VIEW

NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.

1264 mmOPENINGHEIGHT

610 mmOPENING

DEPTH

724 mmOPENING WIDTH

432 mmTYPICAL

TOP VIEW

E

E127mm

102mm

E

E Series Double Oven

STANDARD INSTALLATION

WOLF E SERIES OVENS

wolfappliance.com | 17

WOLF E SERIES OVENS

E

FRONT VIEWSIDE VIEW

*Will be visible and should be finished to match cabinetry.**25 mm for professional and transitional models and 32 mm for contemporary model.

NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.

721 mmFLUSH INSET

HEIGHT

19 mm

10 mm

24 mm

635 mmFLUSH INSET

DEPTHFINISHEDCLEATS*

772 mmFLUSH INSET WIDTH

25 mmOR

32 mm**

TOP VIEW

981 mmTYPICAL

E

E127mm

102mm

E Series Single Oven

FLUSH INSET INSTALLATION

18 | English

E Series Double Oven

FLUSH INSET INSTALLATION

E

FRONT VIEWSIDE VIEW

*Will be visible and should be finished to match cabinetry.**25 mm for professional and transitional models and 32 mm for contemporary model.

NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.

1292 mmFLUSH INSET

HEIGHT

432 mmTYPICAL

19 mm

10 mm

24 mm

772 mmFLUSH INSET WIDTH

635 mmFLUSH INSET

DEPTHFINISHEDCLEATS*

25 mmOR

32 mm**

TOP VIEW

E

E127mm

102mm

WOLF E SERIES OVENS

wolfappliance.com | 19

WOLF CONVECTION STEAM OVENS

Convection Steam Ovens

The legacy of the “combination oven” goes back decades, to innovative chefs in America and Europe who embraced the combination of air movement with superheated steam to achieve superior results—from breads and roasts to delicate fishes, seafood and vegetables. Wolf combines the benefits of convection and steam for the most innovative steam oven on the market today. Virtually any dish prepared in a con-ventional oven, range or microwave can also be prepared in the Wolf convection steam oven—with more control. Three distinct styles compliment the look of Wolf ovens, ranges and cooktops. It can be installed in a standard or flush inset application.

KEY FEATURES

• Convection and steam heat with ten cooking modes for superior control.

• Gourmet and Recipes modes for quick and convenient meal preparation.

• Temperature probe, perforated and solid stainless steel pans.

• Operating time, delayed start and descaling features.

CONVECTION STEAM OVENS

TRANSITIONAL

ICBCSO30TE/S/TH

ICBCSO30TM/S/TH

PROFESSIONAL

CONTEMPORARY

ICBCSO30PE/S/PH

ICBCSO30PM/S/PH

ICBCSO30CM/B/TH

20 | English

OPEN OVEN DOOR

548 mmBEHIND FRAME

454mm

446mm

65mm

538 mm

360mm

22 mm

759 mmWIDTH

SPECIFICATIONS

INTERIOR CAPACITY L

All Models 51

INTERIOR DIMENSIONS W H D

All Models 454 mm 280 mm 400 mm

Convection Steam Oven

DIMENSIONS

WOLF CONVECTION STEAM OVENS

wolfappliance.com | 21

WOLF CONVECTION STEAM OVENS

Planning Information

The convection steam oven can be installed in a standard or flush inset application. A minimum base support of 45 kg is required. The electrical supply for the oven must be located in an adjacent cabinet.

Finish the edges of the opening. They may be visible when the door is open.

For flush inset installations, a minimum 3 mm reveal is required on all sides. To ensure consistent 3 mm reveals, each corner of the opening must be exactly 90°.

TRIM OVERLAP

Top 5 mmBottom 0 mmSides 98 mm

ELECTRICAL

Installation must comply with all applicable electrical codes and be properly grounded (earthed).

Locate the electrical supply as shown in the illustrations on the following pages. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

Performance may be compromised if the electrical supply is less than 220 volts.

ELECTRICAL REQUIREMENTS

Electrical Supply 220-240 VAC, 50 Hz 380-415 VAC 2N, 50 Hz

Service 3700 Watts

Power Cord 2.5 m

22 | English

Convection Steam Oven

STANDARD INSTALLATION

FRONT VIEWSIDE VIEW

Electrical supply must be located in adjacent cabinet within .9 m of opening.Dashed line represents profile of unit.

449 mmOPENINGHEIGHT

548 mmOPENING

DEPTH

TOP VIEW

562 mmOPENING WIDTH

EE

WOLF CONVECTION STEAM OVENS

wolfappliance.com | 23

Convection Steam Oven

FLUSH INSET INSTALLATION

765 mmFLUSH INSET WIDTH

FRONT VIEWSIDE VIEW

FINISHEDCLEATS*

584 mmFLUSH INSET

DEPTH25 mm

*Will be visible and should be finished to match cabinetry.

NOTE: Electrical supply must be located in adjacent cabinet within .9 m of opening.Dashed line represents profile of unit.

460 mm FLUSH INSET

HEIGHT

8 mm

3 mm

102 mmA

TOP VIEW

EE

WOLF CONVECTION STEAM OVENS

24 | English

WOLF GAS COOKTOPS

Gas Cooktops

Like their built-in oven counterparts, the new generation of Wolf gas cooktops features three new looks—Transi-tional, Professional, and Contemporary. New performance enhancements make delicious results even more of a certainty than ever. Multiple sizes, choice of knob colors, distinctly different grates, and even a new way to integrate with custom cabinetry—the new gas cooktops offer excep-tional design flexibility.

KEY FEATURES

• Dual-stacked, sealed burners for precise control and easy cleanup.

• Flame recognition and automatic reignition for safety and ease of use.

• True simmer setting on all burners prevents scorching.

• Illuminated, cool-to-touch knobs for user-friendly comfort.

ICBCG365P/S

ICBCG304P/S

ICBCG365T/S

ICBCG304T/S

ICBCG365C/S

GAS COOKTOPS

TRANSITIONAL

PROFESSIONAL

CONTEMPORARY—COMING SOON!

wolfappliance.com | 25

WOLF GAS COOKTOPS

Gas Cooktops

762 mm TRANSITIONAL 914 mm TRANSITIONAL

762 mm

22 mmALL SIDES

533 mm

102 mm

914 mm

22 mmALL SIDES

102 mm

533 mm

762 mm PROFESSIONAL 914 mm PROFESSIONAL

762 mm

22 mmALL SIDES

533 mm

102 mm

914 mm

22 mmALL SIDES

102 mm

533 mm

BURNER RATING—kW

762 mm GAS COOKTOP HIGH

Large 5.3Medium 3.5(2) Small 2.7

914 mm GAS COOKTOP HIGH

Large 5.3Medium 3.5(3) Small 2.7

26 | English

WOLF GAS COOKTOPS

GAS SUPPLY

A gas supply line of 19 mm rigid pipe must be provided to the cooktop. If local codes permit, a certified, .9 m long, 13 mm or 19 mm ID flexible metal appliance connector is recommended to connect the units 1/2" NPT (or ISO 7/1) male inlet to the gas supply line.

Wolf natural gas cooktops will function up to 3124 m in altitude without adjustment and LP gas cooktops will func-tion up to 2621 m. If the installation exceeds these eleva-tions, contact your authorized Wolf dealer for a high altitude conversion kit.

GAS SUPPLY REQUIREMENTS

NATURAL GAS

Gas Supply Pressure 12.5 mbMin Line Pressure 17.5 mbMax Pressure to Regulator 100 mb

LP GAS

Gas Supply Pressure 25 mbMin Line Pressure 27.4 mbMax Pressure to Regulator 100 mb

Planning Information

A minimum height clearance of 140 mm is required from the top of the countertop to any combustible surface directly below the cooktop.

If a cooktop is being installed above an oven, a minimum of 6 mm is required between units.

ELECTRICAL

Installation must comply with all applicable electrical codes and be properly grounded (earthed).

ELECTRICAL REQUIREMENTS

GAS COOKTOP

Electrical Supply 220-240 V AC, 50/60 HzService 10 amp dedicated circuitReceptacle grounding-type (earthed)

wolfappliance.com | 27

WOLF GAS COOKTOPS

Gas Cooktop

STANDARD INSTALLATION

254 mm

102 mm

89 mm

FRONT VIEWSIDE VIEW

COUNTERTOP CUT-OUT

NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces,combustible materials cannot be located within this area.Electrical and gas supply location only applies to installations with built-in oven.

762 mm

WWIDTH

330 mm457 mm

229mm

495 mm

64 mm

64 mm

E G

CUT-OUT WIDTH

MODEL W

762 mm Cooktop 737 mm914 mm Cooktop 889 mm

28 | English

WOLF COFFEE SYSTEMS

Coffee Systems

Make professional-quality brewed coffee, espresso, cappu-cinno, latte and more. The Wolf coffee system automatically steams and foams the milk perfectly. Water temperature and brew strength are adjustable. Uses either whole-bean or ground coffee. The design pairs beautifully, either side-by-side or in a tower application, with other Wolf products such as the convection steam oven. The coffee system can be installed in a standard or flush inset application.

KEY FEATURES

• Create perfectly brewed coffee, espresso, cappuccino, macchiato and latte at home.

• Separate hot water dispenser for tea.

• Mounted glide system provides easy access to the unit, no direct water line is needed.

• Milk frothing pitcher with adjustable settings, detaches for refrigerated storage and easy cleaning.

• Built-in coffee mill with adjustable grind settings.

• Auto on, auto off and descaling features.

COFFEE SYSTEMS

610 mm MODELS

762 mm E Series Trim

762 mm M Series Trim

TRANSITIONAL

ICBEC24/S

PROFESSIONAL

CONTEMPORARY

762 mm E Series Trim

762 mm M Series Trim

762 mm M Series Trim

ICBEC24/B

wolfappliance.com | 29

WOLF COFFEE SYSTEMS

394 mmBEHIND FRAME

454mm

22 mm

UNITFULL EXTENSION

464mm

WWIDTH

WIDTH

COFFEE SYSTEM W

610 mm Model 597 mm762 mm Model 759 mm

Coffee System

DIMENSIONS

30 | English

Planning Information

The coffee system can be installed in a standard or flush inset application. A minimum base support of 45 kg is required. The sides of the cabinetry opening must be ade-quate to support installation of the mounting slides. Refer to the illustrations below.

Finish the edges of the opening. They may be visible when the door is open.

For flush inset installations, a minimum 3 mm reveal is required on all sides. To ensure consistent 3 mm reveals, each corner of the opening must be exactly 90°.

TRIM OVERLAP

OVERLAP 610 mm MODEL 762 mm MODEL

Top 5 mm 5 mmBottom 0 mm 0 mmSides 18 mm 98 mm

WOLF COFFEE SYSTEMS

ELECTRICAL

Installation must comply with all applicable electrical codes and be properly grounded (earthed).

Locate the electrical supply as shown in the illustrations on the following pages. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

ELECTRICAL REQUIREMENTS

Electrical Supply 230 VAC, 50 Hz

Service 10 amp dedicated circuit

Power Cord 1.8 m

356mm

254mm

19 mmTYPICAL

Side support.

Slide installation.

wolfappliance.com | 31

SLIDESUPPORT

SLIDESUPPORT

FRONT VIEWSIDE VIEW

TOP VIEW

E449 mmOPENINGHEIGHT

548 mmOPENING

DEPTH

WOPENING WIDTH

NOTE: 610 mm and 762 mm models require the same opening dimensions.Dashed line represents profile of unit.

Coffee System

STANDARD INSTALLATION

OPENING WIDTH

COFFEE SYSTEM W

610 mm Model 562 mm762 mm Model 562 mm

WOLF COFFEE SYSTEMS

32 | English

WFLUSH INSET WIDTH

FRONT VIEWSIDE VIEW

FINISHEDCLEATS*

584 mmFLUSHINSETDEPTH25 mm

*Will be visible and should be finished to match cabinetry.

Dashed line represents profile of unit.

460 mm FLUSH INSET

HEIGHT

8 mm

3 mm

A

TOP VIEW

E

SLIDESUPPORT

SLIDESUPPORT

Coffee System

FLUSH INSET INSTALLATION

FLUSH INSET WIDTH

COFFEE SYSTEM W A

610 mm Model 603 mm 21 mm762 mm Model 765 mm 102 mm

WOLF COFFEE SYSTEMS

wolfappliance.com | 33

WOLF DOWNDRAFT SYSTEMS

Downdraft Ventilation

Constructed of heavy duty stainless steel, the Wolf down-draft rises from the countertop to whisk away odor and smoke into stainless steel, mesh filters and can be low-ered beneath the countertop when not in use. Downdrafts integrate perfectly with transitional induction and electric cooktops, gas cooktops and some integrated modules, they can also be installed with 762 mm sealed burner rangetops.

KEY FEATURES

• Three-speed blower control with boost.

• Remote-mounted control module with LED indicators.

• Delay-off feature to automatically turn unit off.

• Stainless steel, mesh filters.

• Reversible motor box.

• Adjustable discharge.

ICBDD45

ICBDD36

ICBDD30

DOWNDRAFTS

34 | English

WOLF DOWNDRAFT SYSTEMS

51 mm

356 mm

730 mm

WDOWNDRAFT WIDTH

ACHIMNEY WIDTH

172mm

254mm

330mm

330mm

381mm

64 mm

60 mm

NOTE: Shaded line represents internal blower box with 152 mm round discharge.

19 mm

Downdraft

DIMENSIONS

WIDTH

MODEL W A

ICBDD30 762 mm 673 mmICBDD36 914 mm 826 mmICBDD45 1143 mm 978 mm

wolfappliance.com | 35

Planning Information

Wolf downdrafts can be installed with most Wolf cooktops, but are not compatible with contemporary induction and electric cooktops and the grill, steamer and fryer modules. Downdrafts can be installed with sealed burner rangetop model ICBSRT304. An accessory trim kit is necessary for this installation. Contact an authorized Wolf dealer for details.

The remote-mounted control module must be located within 3 m of the downdraft assembly and a minimum 76 mm from the edge of the cooktop cut-out.

Internal and remote blowers are available through an autho-rized Wolf dealer.

Internal blowers include a 152 mm round discharge and can be front or rear mounted. It can be discharged in any direc-tion by rotating the blower box. Remote blowers include a 254 mm discharge and can be discharged from the front or rear.

Consult a qualified HVAC professional for specific installa-tion and ducting applications.

WOLF DOWNDRAFT SYSTEMS

ELECTRICAL

Installation must comply with all applicable electrical codes and be properly grounded (earthed).

Certain installations may require that the electrical supply be placed in an adjacent cabinet.

ELECTRICAL REQUIREMENTS

DOWNDRAFTS

Electrical Supply 220-240 V AC, 50 Hz 220 V AC, 60 Hz

Service 10 amp dedicated circuitReceptacle grounding-type (earthed)

36 | English

E

FRONT VIEWSIDE VIEW

*152 mm back from countertop cut-out when internal blower is rear mounted.

NOTE: Internal blower 152 mm round, side, rear or bottom discharge. Remote blower 254 mm round, rear discharge.Centerline indicates center of downdraft cut-out.

540mm

540 mm210 mm*

COOKTOP CUT-OUT

68 mm

TOP VIEW

594 mm

210 mm*

WDOWNDRAFT

CUT-OUT WIDTH

E

WOLF DOWNDRAFT SYSTEMS

Downdraft

INSTALLATION WITH COOKTOP

CUT-OUT WIDTH

MODEL W

ICBDD30 699 mmICBDD36 851 mmICBDD45 1003 mm

wolfappliance.com | 37

FRONT VIEWSIDE VIEW

483 mmPLATFORM DEPTH

FRONT VIEWSIDE VIEW

*152 mm back from countertop cut-out when internal blower is rear mounted.

NOTE: Internal blower 152 mm round, side, rear or bottom discharge. Remote blower 254 mm round, rear discharge.Centerline indicates center of downdraft cut-out.

540mm

210 mm*

TOP VIEW

WDOWNDRAFT

CUT-OUT WIDTH

210 mm*

540 mm 594 mm

RANGETOP OPENING

68 mm E

E

WOLF DOWNDRAFT SYSTEMS

Downdraft

INSTALLATION WITH SEALED BURNER RANGETOP

CUT-OUT WIDTH

MODEL W

ICBDD30 699 mm

38 | English

WOLF DOWNDRAFT SYSTEMS

Downdraft Blower Options

BLOWER

INTERNAL ICBDD30 ICBDD36 ICBDD45

1014 m3/hr • • •

REMOTE ICBDD30 ICBDD36 ICBDD45

1014 m3/hr • • •2028 m3/hr • • •

Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc. Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service marks of Sub-Zero, Inc. (collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.

wolfappliance.com | 39

Wolf Products Limited Warranty

INTERNATIONAL PRODUCTS

FOR RESIDENTIAL USE ONLY

FULL TWO YEAR WARRANTY

For two years from the date of original installation, your Wolf Appliance product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Wolf Appliance under the above warranty must be performed by Wolf factory certified service, unless otherwise specified by Wolf Appliance, Inc. Service will be provided during normal business hours.

LIMITED THIRD THROUGH FIFTH YEAR WARRANTY

For five years from the date of original installation, Wolf Appliance will repair or replace the following parts that prove to be defective in materials or workmanship: gas burners (excluding appearance), electric heating elements, blower motors (ventilation hoods), electronic control boards, magnetron tubes and induction generators. The part(s) will be repaired or replaced, free of charge, with the owner paying for all other costs including labor. All service provided by Wolf Appliance under the above warranty must be performed by Wolf factory certified service, unless otherwise specified by Wolf Appliance, Inc. Service will be provided during normal business hours.

WOLF APPLIANCE, INC.

PO BOX 44848

MADISON, WI 53744 USA

WOLFAPPLIANCE.COM

I W N G D G 1 2 / 2 0 1 3