01/01/2011

SOME MORE QUESTIONS ASKED ABOUT OUR MARLIN SPORTSTER

Must I buy all the parts to build my Sportster at the outset?No, it is not necessary to buy all the parts at one time but most initial orders include most of the major components to build to the rolling chassis stage as listed in the modules below.

Is there any weather equipment?Yes, there is a very easy to erect roof with side panels. The roof is water tight and stores away behind the seats, taking up very little space, space when not in use.

Can I race my Sportster?Yes, Marlin successfully raced in the 750 series club championship at various race courses throughout England and Wales. The Sportster has also been extremely successful in endurance events and hill climbing.

The seven type cars I’ve tried are too small, what’s the space like in a Sportster?There is ample width and length in the cockpit for most people up to 6’ 6” / 16 stone space will seem limited.

How easy is the manual to follow?Marlin has produced a CD manual with sets of pictures detailing the various stages of the build along with a paper specification manual.

COMING SOON IN 2011A complete one piece roof system that folds away neatly on to the back of the car leaving all the space behind the seats free for extra luggage . Photo’s available soon.For more information please contact Terry on 01363 773772

The order form is at the end of the price list

……………………………………………………………………………………………………………………………………………………………………….

Sportster Price List

Purchase Modules 1, 2, & 3 together for Only £6,000.00 (PLUS VAT)

Saving £522.00 (INC VAT)

MODULE ONE STARTER KIT

1 X MARLIN SEMI-MONOCOQUE PERIPHERAL FRAME CHASSIS Chassis and all steel components are shot blast and powdercoated. Some specifications may vary depending on donor specification.

The Chassis frame has all suspension & steering positions drilled plus jigged location points for seat belts and doors plus energy absorbing de-forming bumpers. All modules come with fastener packs.

1 x Battery box2 x Door hinge & closure posts1 x Fire wall bulkhead1 x Steel transmission tunnel1 x Welded in RAC specification CDS roll bar4 x Adjustable top arm joints & nuts 2 x Ball joint sockets for top arm 2 x Differential to chassis mount brackets1 x Differential mount bracket carrier 2 x Floor sections (galvanized steel) 1 x Gear box mount (use std rubber mounts) 1 x Handbrake cable mounting tube

1 x Master cylinder adapter plate

Module 1 continued:

1 x Mounting bar rail (for seat belts) with fittings 2 x Rear spring seats (adjustable) 1 x Steering column floor bush tube 2 x Steering column spacer tubes2 x Suspension arms top (front)2 x Suspension arms lower (front) 8 x Urethane suspension bush kits

HYDRAULIC PEDAL BOX ASSEMBLY to include:1 x Factory modification of BMW strut assemblies (taken from your donor parts)2 x Lower radiator mounting brackets 2 x Engine mount rubbers 2 x Engine mount arms 1 x Radiator top brace

1 x Set HEL Brake hose kit complete stainless steel (all flexible hoses) 4 x Front suspension ball joints 1 x Marlin stainless steel badge 2 x Shock absorbers front (coil over adjustable to suit 2¼ ø springs) 2 x Springs front (Marlin rate 2¼ ø) 1 x Steering extension shaft (specially made for Marlin with UJ) 1 x Steering rack (specially made for Marlin with standard ratio) 2 x Track rod ends

Module 1 Price £ 3,900.00

The following can be added at this stage as additional parts

1 x Brake fluid reservoir & switch £ 58.99 1 x Brake fluid reservoir hose £ 13.99 1 x Brake hose kit for rear discs (2 piece) £ 20.99 20 x Brake pipe clips £ 6.40

1 x Brake master cylinder (can take from donor) £ 74.75 2 x Brake master cylinder elbows £ 3.80 1 x Brake servo £ 179.99

1 x Clutch hose (pressure) £ 33.98 1 x Clutch master cylinder (0.75) £ 86.99 1 x Chassis build stands rental (for 12 months) £ 109.98

MODULE TWO - Some Body and Kit parts

1 x Dashboard panel (aluminum)2 x Scuttle closure panel pieces (aluminum)

1 x Bonnet rear support (composite)1 x Nose cone (composite)

FUEL TANK KIT (aluminium) to include: 1 x Eight gallon tank (baffled for fuel injection supply) 1 x One way air vent valve 2 x Long tank straps 2 x Short tank straps 1 x length 50mm connection hose 1 x Length installation rubber 2 50mm Hose clips 1 x Hose mounted filler neck 1 x Remote expansion bottle kit (including cap and hose)

Module 2 Price £ 755.00

The following can be added at this stage as additional parts

Exhaust system for e30 & e36 1 x Manifold front 1 x Manifold rear 1 x De-Cat pipe 1 x ‘Y’ Section cross pipe 1 x Left hand link and side pipe 1 x Right hand side pipe 2 x Re-Packable silencers 1 x Silencer 2 x Straps and fixings £ 852.50

1 x Catalytic converter (universal) £ 85.00

2 x Stainless steel exhaust escution rings £ 15.00

1 x Fuel injection pump (high pressure) £ 99.99 1 x Fuel injection feed pump (low pressure) £ 67.99 1 x Fuel swirl pot (aluminum) £ 65.99 1 x Fuel level sender £ 32.99

1 x Grill mesh – stainless steel £ 79.99 1 x Electric fan kit 12” (inc thermostat and brackets) £ 119.99 1 x Propshaft (made to order) (can use donor) £ 184.99

1 x Carbon fiber dashboard £ 155.00 1 x Wiring loom (complete with fuse box and instructions) (can use donor) £ 179.00

Instrument kit x 6 gauges (electronic) black or cream available 1 x 80 mm Rev Counter 1 x 80 mm Speedo 1 x 50 mm Oil pressure gauge 1 x 50 mm Fuel gauge 1 x 50mm Water Temperature gauge 1 x 50mm Volt meter 1 x Water Temperature Sender 1 x Oil pressure sender 1 x Fog light switch 1 x Hazard Light Switch 1 x Brake/fluid Warning Light 1 x Main beam Warning Light 1 x Ignition Warning Light 1 x Indicator Warning Light 1 x Oil Warning Light £ 588.00

MODULE THREE – Rest of Body parts and Kit parts 2 x 'A' panels (aluminum)2 x Bonnet tops (aluminum)2 x Bonnet side panels (aluminum)2 x Bonnet stiffeners (aluminum)2 x Doors with door pockets & hinge assemblies (aluminum)2 x Door internal brace panels (aluminum)

2 x Front wings (composite)2 x Rear wings (composite)1 x Tail section (composite)2 x Front wing mounting stays (steel)

Module 3 continued:

1 x Wing piping 1 x Bonnet rest rubber

DOOR LATCHING KIT2 x Striker pins2 x Striker plates2 x Striker washers

2 x Latch sets – LH & RH

4 x Bonnet catches chrome 1 x Bonnet stainless steel center hinge 1 x Bumper kit (with special impact deforming struts front & rear) 2 x Door mirrors stainless steel

Module 3 Price £ 1,780.00

Kit parts to help finish your build

1 x Body assembly & alignment fitment service (we fit the body panels to your car) £ 659.00 2 x Exhaust protection bars (with stainless steel ‘Sportster’ scripted plates) £ 149.99 1 x Hard glass fiber spare wheel cover (to fit 195 x 70 spare) £ 129.99

Interior trim kit 1 x Carpet cut to shape (Charcoal) 2 x Door combing's (black vinyl) 1 x Dashboard combing (black vinyl) 1 x Gear change gaiter (black vinyl) 1 x Hand brake gaiter (black vinyl) 1 x Stainless steel gear ring 1 x Stainless steel hand brake ring 2 x Full size rubber foot mats 2 x Door retaining straps 1 x Door rubber seal set 1 x Fixings set £ 357.50

Lighting kit 2 x Chrome headlamp shells inc quartz halogen side lights 2 x Headlamp brackets 2 x Front stalk indicator lamps 2 x Repeater indicators & brackets (in wings) 2 x Rear light assemblies 2 x Number plate lights 1 x Rear fog light 1 x Reversing light £ 199.99

2 x Chrome spot lights and halogen bulbs £ 116.00 2 x Seat belts inertia roll £ 85.98 2 x (FIA) Marlin special 4 point harness seat belts £ 220.00 1 x Tonnaue cover (PVC special 4 zip style inc fastenings) £ 325.00 2 x Aero screens £ 139.98

1 x Washer bottle & pump £ 32.00 1 x Boot rack (stainless steel with fasteners) £ 169.99 1 x Front number plate holder (aluminum) £ 35.00

Wiper kit 3 blade type 1 x Motor 3 x Wiper arms & blades 1 x Mounting rubber 3 x Standard spindles 4 x lengths copper sleeve pipe (various) £ 240.00

Windscreen assembly (polished aluminum tilt & slide windscreen) 1 x Windscreen & surround 1 x Screen base / plinth - aluminum 2 x stainless steel side supports 2 x M6 turn knobs 1 x 1m small self adhesive foam 1 x 1m small rubber 'U' section 1 x 1.1m small rubber 'U' section 4 x M5 stainless steel pan HD allen screws 4 x M5 nylocs 4 x M8 x 30 bolts 8 x M8 penny washers 4 x M8 nylocs 2 x Side pillar support brackets £ 329.99

MSC LTD SPECIALIST SPORTS CAR MANUFACTURER

Sportster Order Form

Name

Address

Daytime Telephone Mobile

Email

Module 1 £ 3,900.00Total cost of extra’s (from module 1) £

Module 2 £ 755.00Total cost of extra’s (from module 2) £

Module 3 £ 1,780.00

Any other parts added £

Sub Total 1 £

Plus Vat @ 20% £Sub Total 2 £

Less deposit (vat inc) £ 500.00

Less discount if buying all 3 modules (Vat inc) £ 522.00

Final Total owing on collection/delivery £

Please pay by cheque or toLloyds TSBSort Code: 30-93-14Account Number: 01016108

01363 773 772 design / development / manufacturewww.marlinsportscars.co.uk Vat No GB 937 311 39 MSC Ltd – PO Box 88 – Crediton – Devon – EX17 3WZ