NN-205~2

Alcatel-Lucent 9300 W-CDMA Product Family | V7.1 Parameter Reference Guide - C-Node Parameters
Alcatel-Lucent - Internal Proprietary - Use pursuant to Company Instruction
NN-20500-027 Issue 11.02
Parameter Reference Guide - C-Node Parameters
Document number: NN-20500-027 Document issue: 11.02 Document status: Preliminary Product release: V7.1 Date: November 2009
Alcatel-Lucent - Internal - Proprietary - Use pursuant to Company instruction
Copyright © 2001-2009 Alcatel-Lucent, All Rights Reserved
UNCONTROLLED COPY: The master of this document is stored on an electronic database and is "write protected"; it may be altered only by authorized persons. While copies may be printed, it is not recommended. Viewing of the master electronically ensures access to the current issue. Any hardcopies taken must be regarded as uncontrolled copies.
ALCATEL-LUCENT CONFIDENTIAL: The information contained in this document is the property of Alcatel-Lucent. Except as expressly authorized in writing by Alcatel-Lucent, the holder shall keep all information contained herein confidential, shall disclose the information only to its employees with a need to know, and shall protect the information from disclosure and dissemination to third parties. Except as expressly authorized in writing by Alcatel-Lucent, the holder is granted no rights to use the information contained herein. If you have received this document in error, please notify the sender and destroy it immediately.
Alcatel-Lucent, Alcatel, Lucent Technologies and their respective logos are trademarks and service marks of Alcatel-Lucent, Alcatel and Lucent Technologies.
All other trademarks are the property of their owners.

November 2009
Issue 10.03/EN Preliminary
Update after review
Resolution of CR DCTPD00169086 "ALTP Review: One change need to be made in
ALTP - NN-20500-027"
June 2009

November 2008
SYSTEM RELEASE: OAM05.2

February 2007
November 2006
Update for OAM 5.1/UA 5.0 [UMTS V5.1]
The Publication History information for the outdated releases has been deleted. Document creation date: May 2004
Publication history 5

List of figures 18

1 About this publication
This document provides the RAN Model information and a list of the user accessible UMTS Access
Network configuration parameters.
Audience
This document is intended for installation, operation, engineering and validation personnel, and any
other user who wants to know more about the UTRAN configuration parameters.
Prerequisites
It is recommended that readers become familiar with the following technical documents:
• Alcatel-Lucent 9353 Management System - System Overview (NN-20500-031)
How this publication is organized
This document is organized as follows:
• Volume 1: RAN Model Information
— RAN Model diagrams
— Index of customer parameters
— Index of manufacturer parameters
• Volume 3: INode Parameters
• Volume 4: NodeB Parameters

— Parameter description
• Volume 6: OneBTS Parameters
• Volume 7: OAM Parameters
• Volume 8: POC7K Parameters
• Volume 9: POC15K Parameters
Vocabulary conventions
For a list of UMTS terms used in the publication, refer to theAlcatel-Lucent 9300 W-CDMA Product
Family - Terminology ( NN-20500-002).

2 Roadmap to Configuration Management documentation
The figure next page shows where the current document stands within the W-CDMA Customer
Documentation.
Note: For a global view of the W-CDMA Customer Documentation, see Roadmap chapter in:
• Alcatel-Lucent 9300 W-CDMA Product Family - Document Collection Overview (NN-20500-050)
• Alcatel-Lucent 9300 W-CDMA Product Family - Access Network Management Overview (NN-20500-031)
Figure 1 Roadmap to Configuration Management documentation
21

3 Object/Parameter description
This section gives the description of customer available objects and parameters.
Introduction
Parameters belong to a containing object. Object descriptions can be found in the first volume.
In the volumes 2 to 9, the parameters are grouped by Network Element: CNode, INode, NodeB,
OAM, POC7K, POC15K (each volume is dedicated to 1 Network Element) and by containing object
(those objects being alphabetically sorted for each Network Element).
For further information on the parameters network engineering, please contact your Account
Manager who will support you into getting the UTRAN Parameters User Guide (UPUG) issued by
Alcatel-Lucent Wireless Network Engineering group.
Object description
RNC objects have a unique name different from their name.
NodeB and OAM objects have a unique name equal to their name.
In each volume (from volume 2 to 9), the objects are sorted by alphabetical order according to their
Unique Name.
For each object, the following general information are presented:
• presence: the value of this field can be "optional" or "required"
• onlineCreation: the value of this field can be "AllowedWithParent" or "Allowed" or "NotAllowed".
• onlineDeletion: the value of this field can be "AllowedWithParent" or "Allowed" or "NotAllowed".
• verbs: the value of this field can be "add" or/and "delete", and it is used for Passport provisioning.
• parents: this field gives the list of the containing objects
• children: this field gives the list of the contained objects
• identifiers: this field gives the list of the identifiers, and for each one, the corresponding IDcategory, IDqualifier, IDscope, Mininstances, Maxinstances as follows:
Name IDcategory IDqualifier IDscope Mininstances Maxinstances
Parameter description
• parameter name

• domain: the three kinds of domains are:
— RNC: parameters are part of the RNC MIB definition and are hosted by WMS OAM and Network Element RNC
— BTS: parameters are part of the BTS MIB definition and are hosted by WMS OAM and Network Element BTS
— IN: parameters are part of the Inode MIB definition and are hosted by WMS OAM and Network Element Inode
— AN: parameters are part of the Anode MIB definition and are hosted by WMS OAM and Network Element Anode
— OAM: parameters are part of the WMS OAM MIB definition and are hosted by WMS OAM only. Its are not declared in any Network Element MIB, so its are not mediated by build function and not checked by audit function.
• description: the parameter definition
• class: the four kinds of class are:
— 0: The parameter cannot be modified and a new object instance must be created with the requested parameter value thanks to build process or on line command.
— 2: The object instance (or one of the parent object instance) must be locked to modify the parameter and the modification will be taken into account after the object instance (or the parent object instance) has been unlocked.
— 3: So called "on-line parameter definition". The object instance does not need to be locked to modify the parameter and the modification will immediately be taken into account with no impact on the service availability.
— READ ONLY: The "read only" parameters can only be displayed.
• presence: indicates if the configuration of the parameter is optional.
• visibility
Customer parameter accessible for the customer (read/write or read only)
Manufacturer Alcatel-Lucent defines these parameters and they are not accessible for
customer
stricted
parameters that can be modified by the customer, but it is strongly recom-
mended to set them according to Alcatel-Lucent specification as their modi-
fications can have performance impacts on WMS
• data type: decimal, integer, float, boolean, etc.
• unit: the measurement unit of the value range, when applicable.
Unit

— Enum (AdministrativeState): locked (0), unlocked (1), shuttingdown (2)
— String: length = 40 (Hex)
— Integer: min = 0, max = nRouteSet-1
• initial value: the value of a new parameter is [#false#] or [#null#] or [x]. This value is used:
— either when a customer wants to ensure the same performances before a UTRAN release upgrade
— or when a customer wants to deactivate a function
• def value comments
• recommended value: this value is recommended by Alcatel-Lucent for new networks roll out before the optimization. The recommended values take benefit of the performance of UTRAN feature. For installed networks, the value to set depends on the chosen options or rules defined by the customer.
• rec val comments
Index description
At the end of each volume (from volume 2 to volume 9), two indexes are available summarizing all
the parameters presented in the concerned volume:
• an index for the customer parameters
• an index for the manufacturer parameters
26

These two indexes list the parameters by category (standard, inventory, states and status, dynamic
data, I&C) and by object sorted by alphabetical order, as follows:
• standard parameters
— Object A
– Parameter AA
– Parameter AB
– Parameter AC
— Object B
– Parameter BA
– Parameter BB
• inventory parameters
— Object A
– Parameter AD
– Parameter AE
— Object C
– Parameter CA
– Parameter CB
– Parameter CC

4 Features Market Applicability
This chapter presents a global view of theV7.0 Features included in this document.
For each feature, the title and the market applicability are detailed.
Note: Only the V7 features are listed in this table. If a feature Id introduced in a counter's description has no entry in this table, this feature comes from an old features load.
FRS Id FRS Title Visible and applicable to all Global Market (GM)
Visible and applicable to ATT
27615 GPS Assistance data developments yes no
34406 UTRAN positioning for Low Delay location requests - testing using the WSC 5060
yes no
34403 AMR Code Set 2 with TrFO yes yes
28528 Multi-Operator Core Network (MOCN)
yes no
yes yes
yes no
34018 Multiple PS I/B on HSUPA yes no
34613 Additional service information in UT- RAN Service View and Equipment Monitor
yes no
yes no
75069 iMCTA improvement yes yes
34613 Additional service information in UT- RAN Service View and Equipment Monitor
yes no
33331 Alarm HHO based on UE TX Power yes no
34697 DRNC Counters at Cell Level yes no
27649 Native IP Iub support yes no
34648 Counter capacity improvement. counter volume control
yes yes
29

yes yes
yes yes
25101 Real Time RNC Counters yes no
78328 Globalization of 34246 Power Con- trol Enhancements
yes no

• Presence: required
• OnLineCreation: NotAllowed
• OnLineDeletion: NotAllowed
MaxIn- stances
Links:
Parameters:
rdnId
Class NA
Presence required
Visibility customer

Domain RNC
Description Defines the Horizontal Accuracy, which will be requested to UE for its location fix. It is expressed as "uncertainty code" k. So the uncertainty in meter is derived from formula r = 10*(1.1(^k)-1) in meters. Cf. 23.032
Class 3
Presence required
Visibility customer
Range [0..127]
Domain RNC
Description It clarifies the presence or not of UE Positioning GPS acquisition assistance data the RNC is allowed to sent to UE using RRC MEASUREMENT CONTROL procedure
Class 3
Presence required
Visibility customer
Domain RNC
Description It clarifies the presence or not of UE Positioning GPS assistance almanac data the RNC is allowed to sent to UE using RRC MEASUREMENT CON- TROL procedure
32

Domain RNC
Description It clarifies the presence or not of UE Positioning GPS assistance ionospheric model data the RNC is allowed to sent to UE using RRC MEASUREMENT CONTROL procedure
Class 3
Presence required
Visibility customer
Domain RNC
Description It clarifies the presence or not of UE Positioning GPS assistance navigation model data the RNC is allowed to sent to UE using RRC MEASUREMENT CONTROL procedure
Class 3
Presence required
Visibility customer

Domain RNC
Description It clarifies the presence or not of UE Positioning GPS assistance real time integrity data the RNC is allowed to sent to UE using RRC MEASUREMENT CONTROL procedure
Class 3
Presence required
Visibility customer
Domain RNC
Description It clarifies the presence or not of UE Positioning GPS assistance reference location data the RNC is allowed to sent to UE using RRC MEASUREMENT CONTROL procedure
Class 3
Presence required
Visibility customer
Domain RNC
Description It clarifies the presence or not of UE Positioning GPS assistance reference time data the RNC is allowed to sent to UE using RRC MEASUREMENT CONTROL procedure
Class 3
Presence required
Visibility customer

Domain RNC
Description It clarifies the presence or not of UE Positioning GPS assistance data the RNC is allowed to sent to UE using RRC MEASUREMENT CONTROL procedure
Class 3
Presence required
Visibility customer
Domain RNC
Description Defines the maximum number of GPS Satellites (SV) for which navigation model assistance is delivered to UE per GPS position attempt
Class 3
Presence required
Visibility customer
Range [4..16]
Domain RNC
Description Defines the maximum number of GPS Satellites (SV) for which GPS almanac assistance is delivered to UE per GPS position attempt
Class 3

Domain RNC
Description Defines the number of GPS Satellites (SV) for which GPS assistance data are delivered to UE. This parameter is only relevant for GPS reference time and GPS acquisition assistance information, if integrated SMLC is depoyed. In a SAS deployment scenario this parameters is relevant for GPS reference time, GPS acquisition assistance, almanac and navigation models.
Class 3
Presence required
Visibility customer
Range [4..12]
Domain RNC
Description Specifies the value of the interval of periodical report to be used in RRC Measurement Control message send of UE audit phase, if the response time in RANAP Location Reporting Control is equal to Dealy Tolerant..
Class 3
Presence required
Visibility customer
Unit ms
36

Data type Enumeration
Initial value 1000
Rel version comments Release Version Warning: parameter not used by the system in this release version. It must not be set if optional, or set to its default value if mandatory.
Class 3 detail A2
Domain RNC
Description Specifies the value of the interval of periodical report to be used in RRC Measurement Control message send of UE audit phase, if the response time in RANAP Location Reporting Control is equal to Low Delay..
Class 3
Presence required
Visibility customer
Unit ms
Range 250, 500, 1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000, 20000, 24000, 28000, 32000, 64000
Initial value 1000
Domain RNC
Description Specifies the value of the interval of periodical report to be used in last RRC Measurement Control message send (i.e. Transfer phase) for delay tolerant requests.
Class 3
Presence required
Visibility customer
Unit ms
Range 250, 500, 1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000, 20000, 24000, 28000, 32000, 64000
37

Initial value 16000
Class 3 detail A2
Domain RNC
Description Specifies the value of the interval of periodical report to be used in last RRC Measurement Control message send (i.e. Transfer phase) for delay tolerant requests.
Class 3
Presence required
Visibility customer
Unit ms
Range 250, 500, 1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000, 20000, 24000, 28000, 32000, 64000
Initial value 8000
Domain RNC
Description Minimum delay between successive emission by RNC of a RRC MEASUREMENT CONTROL message including GPS assistance data
Class 3
Presence required
Visibility customer
Unit ms
Range [10..20000]

Domain RNC
Description Maximum time for acquiring the delay sensitive GPS Assistance data from SAS
Class 3
Presence required
Visibility customer
Unit ms
Range [10..20000]
Description Maximum time for transferring the delay sensitive GPS Assistance data from SAS
Class 3
Presence required
Visibility customer
Unit ms
Range [10..20000]
Domain OAM
Description Information field reserved to the user. No specific treatment on this field is performed by the system.
Class NA
Presence optional
Visibility customer
Range [0..30]

Domain RNC
Description Defines the Vertical Accuracy, which will be requested to UE for its location fix. It is expressed as "uncertainty code" k. So the uncertainty in meter is derived from formula r = 45*(1.025(^k)-1) in meters. Cf. 23.032
Class 3
Presence required
Visibility customer
Range [0..127]

• Presence: optional
• OnLineCreation: Allowed
• OnLineDeletion: Allowed
MaxIn- stances
Links:
Parameters:
rdnId
Class NA
Presence required
Visibility customer

Data type Decimal
Initial value N.A.
Class 3 detail A2
Data type Decimal
Initial value N.A.
Class 3 detail A2
42

culation (PM30171-1) ueBasedTemor- aryV4Param02[0] -> isDynamicDeltaCfnCalculation ueBasedTemoraryV4Param02[1 - 9] -> psCalls- DeltaCfnDelay represents the delay*2 + 1 in ms to add to the Always-on Downsize and DL RB Rate Adaptation Downsize case The parameter isDy- namicDeltaCfnCalculation is initialized to be TRUE as the feature is activated; while the parameter psCallsDeltaCfnDelay is initialized to be 0 if the feature is deactivated.
Class 3
Presence optional
Visibility customer
Range [0..2147483647]
Rel version comments .

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description This parameter defines the duration for which network access will be restricted for a set of access classes.
Class 3
Presence required
Visibility customer
Unit min
Range [1..5]
Domain RNC
Description This parameter defines if the access class barring is activated or not.
Class 3
Presence required
Visibility customer
Domain RNC
Description This parameter defines the percentage of CS domain access classes to be barred. 1 class =10% while all 10 classes = 100%.
Class 3
Presence required
Visibility customer

Domain RNC
Description This parameter defines the percentage of PS domain access classes to be barred. 1 class =10% while all 10 classes = 100%.
Class 3
Presence required
Visibility customer
Domain RNC
Description X.731 (OSI state) : The availability status attribute is read-only. It can have zero or more of the following values and needs to be associated with operational state in order to be usefull: # dependency, with the operational state set to disabled: The profile is activated, but there is no NodeB associated to this profile. # offLine, with the operational state set to disabled: default value at creation with the activation flag set to false. # {Idle}, with the operational state set to enabled: This profile is running and at least one NodeB (up or not) is associated to this profile.
Class NA
Presence required
Visibility customer
Data type Variable[9] List of Enumeration
46

Domain RNC
Description X.731 (OSI state) : The operational state attribute is single-valued and read-only. It can have one of the following values, and needs to be associated with availability status in order to be usefull. # Disabled: The profile is not running. # Enabled: The profile is running, and at least a NodeB is associated to this profile.
Class NA
Presence required
Visibility customer
Domain OAM
Description Information field reserved to the user. No specific treatment on this field is performed by the system
Class NA
Presence optional
Visibility customer
Range [0..256]

• OnLineDeletion: AllowedWithLock
Child(ren):
MaxIn- stances
Links:
Parameters:
rdnId
Description AccessServiceClass identifier. The range is given according to the maxASC in the TS 25.331 3GPP.
Class NA
Presence required
Visibility customer

Domain RNC
Description TS 25.331 Assigned Sub-Channel Number This bit string, which will be repeated 3 or 4times according to the value of the parameter aichtransmissiontim- ing, indicates the sub-channels assigned to the respective ASC.
Class 3
Presence required
Visibility customer
Range [4..4]
availableSignatureEndIndex
Domain RNC
Description TS 25.331 Available signature End Index One ASC has access to all the signatures between the Avail- able signature Start Index and the Available signature End Index.
Class 3
Presence required
Visibility customer
Range [0..15]

availableSignatureStartIndex
Domain RNC
Description TS 25.331 Available signature Start Index One ASC has access to all the signatures between the Avail- able signature Start Index and the Available signature End Index.
Class 3
Presence required
Visibility customer
Range [0..15]
userSpecificInfo
50

Class NA
Presence optional
Visibility customer
Range NA

• OnLineCreation: AllowedWithLock
• OnLineDeletion: AllowedWithLock
MaxIn- stances
Links:
Parameters:
rdnId
Domain RNC
Description 3GPP TS 12.08: "Subscriber and equipment trace". CTb (Call trace Type b) session Identifier,
Class NA
Presence required
Visibility customer

Domain RNC
Description The trace file for this session is made available at the end of each such period if there is no other reason why to close a trace file (end of session or maximum file size reached).
Class 0
Presence required
Visibility customer
Unit min
Range [1..60]
Domain RNC
Description Indicates the maximum size of a trace file. Once this size reached the Trace file is made available for the upload and the OMC notified of its availability.
Class 0
Presence required

Class 0
Presence required
Visibility customer
Unit min
Range [0..65535]
Domain RNC
Description Identifier choosen by the OAM system, this is read only for the end user, will be the externalSessionId of the children session. This value is used to gather datas from different session in the Utran network
Class 0
Presence required
Visibility manufacturer
Range [0..2147483647]
54

Domain RNC
Description Mainly for cell RACH channel monitoring. Usually it required to specified one cell or two. If no cell is specified (i.e., the number of cells is set to 0), cell KPI tracing is not required.
Class 0
Presence required
Visibility customer
Range NA
Initial value
Description Indicates duration of Uplane throughput monitoring, unit: in seconds
Class 0
Presence required
Visibility customer
Unit s
Range [10..3600]

Domain RNC
Description Indicates whether Call Trace data blocks issued in this session have to be reported in real time
Class 0
Presence required
Visibility customer
Domain RNC
Description Provides the IP address of the computer hosting the Real Time Call Trace Analyzer tool
Class 0
Presence required
Visibility customer
Data type Ip4Address
Initial value N.A.
Domain RNC
Description Time between the session creation and the session first activation.
Class 0
Presence required
Visibility customer
Unit min
Range [0..1440]

Class 0
Presence required
Visibility customer
Initial value imsi
Domain RNC
Description Value of the UE identifier (IMSI, TMSI, P-TMSI or IMEI) iof the mobile to trace,
Class 0
Presence required
Visibility customer
Range NA

• OnLineCreation: AllowedWithParent
• OnLineDeletion: AllowedWithParent
MaxIn- stances
Links:
Parameters:
rdnId
Class NA
Presence required
Visibility customer

Description Globally enable/disable the RLC adaptive status filter feature
Class 3
Presence required
Visibility customer

MaxIn- stances
Links:
Parameters:
rdnId

Child(ren):
MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description TS23.003 subclause 4.1(release 1999) Mobile Country Code (MCC) identifies the country in which the PLMN is located. The value of the MCC is the same as the three digit MCC contained in interna- tional mobile subscriber identity (IMSI). mobile- CountryCode parameter is a 3 digits BCD-string (each digit is coded on 4 bits, which results finally in a 12 bits-long string).
Class 3
Presence required
Visibility customer
Range [3..3]
Domain RNC
Description TS23.003 subclause 4.1(release 1999) mobileNet- workCode of the network entity Mobile Network Code (MNC) is a code identifying the PLMN in that country. The MNC takes the same value as the two or three digit MNC contained in IMSI. mobileNet- workCode parameter is a 2 or 3 digits BCD-string (each digit is coded on 4 bits, resulting in an 8 or 12 bits-long string).
Class 3
Presence required
Visibility customer
Range [2..3]

Description information field reserved to the user. No specific treatment on this field is performed by the system.
Class NA
Presence optional
Visibility customer
Range [0..30]

MaxIn- stances
Links:
alwaysOnDlMultipleRb- SetFachId

Domain RNC
Description Identity of the DL Radio Bearer set used in the Al- ways-On configuration in CELL_FACH for (PS I/B + PS I/B) RABs combination
Class 3
Presence optional
Visibility customer
Range DlRbSetConf
Domain RNC
Description Identity of the Dl radio bearer set used in the Al- ways On configuration in DCH
Class 3
Presence optional
Visibility customer
Range DlRbSetConf

Domain RNC
Description Identity of the Dl radio bearer set used in the Al- ways On configuration in FACH
Class 3
Presence optional
Visibility customer
Range DlRbSetConf
Domain RNC
Description Identity of the UL Radio Bearer set used in the Al- ways-On configuration in CELL_FACH for (PS I/B + PS I/B) RABs combination
Class 3
Presence optional
Visibility customer
Range UlRbSetConf
Domain RNC
Description Identity of the Ul radio bearer set used in the Al- ways On configuration in DCH
Class 3
Presence optional
Visibility customer
Range UlRbSetConf

Domain RNC
Description Identity of the Ul radio bearer set used in the Al- ways On configuration in FACH
Class 3
Presence optional
Visibility customer
Range UlRbSetConf
Domain RNC
Description This parameter indicates if the procedure Always on is allowed
Class 3
Presence required
Visibility customer
Domain RNC
Description This parameter is used when the UE has multiple I/ B PS RABs present (Without streaming) to determine whether the RNC releases a RAB after a period of releaseTimerMpdpChannelType on the RAB (FALSE), or whether it releases the whole Iu based
68

upon inactivity on all of the RABs (TRUE). In addi- tion, parameter releaseTimerMpdpChannelType describes the behavior when this is set to FALSE, and parameter timer T2 describes the behavior when this is set to TRUE.
Class 3
Presence required
Visibility customer
Range false, true
Initial value false
Recommended value Should generally be set by default to TRUE on Ex- Nortel deployments and FALSE on Ex-Lucent deployments.
Class 3 detail A2
Domain RNC
Description Coefficient to apply to AO timer length for PS interactive siganling RAB; regular AO timer (T1) * this coeff
Class 3
Presence required
Visibility customer
Domain OAM
Class NA
Presence optional
Visibility customer

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description This is the time required for the MAC-d to hold off informing the RRC that a PS RAB is inactive when there are more than 2 PS RABs for a UE. There is one specific value for each of the OLS levels (Gold, Silver Bronze), in the case that there are multiple RABs mapped with different OLS, the timer for the most stringent OLS is used
Class 3
Presence required
Visibility customer
Unit ms
Domain RNC
Description This timer is set when the UE traffic indicator becomes below the ThroughputThreshold Step 1. On timer expiration, the UE is downgraded to always- on radio configuration.
Class 3
Presence required
Visibility customer
Unit ms
73

the ThroughputThreshold Step 1, when the call is configured with CPC.
Class 3
Presence required
Visibility customer
Unit ms
Description Set when the UE traffic indicator becomes below the ThroughputThreshold Step 1, for PS RAB on HSDPA only.
Class 3
Presence required
Visibility customer
Unit ms
Rec val comments
Description set when the UE traffic indicator becomes below the ThroughputThreshold Step 1 for a PS RAB on HS- DPA/EDCH only.
Class 3
Presence required
Visibility customer

Domain RNC
Description This timer is set when the UE traffic indicator becomes below the ThroughputThreshold Step 2. On timer expiration, the UE context is released from RNC. It enters into GMM idle mode (NAS state)..
Class 3
Presence required
Visibility customer
Unit ms
Range [10..10800000]
Description Set when the UE traffic indicator becomes below the ThroughputThreshold Step 2, when the call is configured with CPC.
Class 3
Presence required
Visibility customer
Unit ms

Description Set when the UE traffic indicator becomes below the ThroughputThreshold Step 2, for PS RAB on HSDPA only.
Class 3
Presence required
Visibility customer
Unit ms
Range [10..10800000]
Rec val comments
Description set when the UE traffic indicator becomes below the ThroughputThreshold Step 2 for a PS RAB on HS- DPA/EDCH only.
Class 3
Presence required
Visibility customer
Unit ms
Range [10..10800000]

Domain OAM
Class NA
Presence optional
Visibility customer
Range [0..30]
Rec val comments

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description TS 25.331 Pending time after trigger Ii indicates the period of time during which it is forbidden to send any new measurement reports with the same Traffic volume event identity even if the triggering condition is fulfilled. It is part of upsize algorithm.
Class 3
Presence required
Visibility customer
Unit ms
Domain RNC
Description TS 25.331 Reporting Threshold This parameter is part of the Traffic Volume Measurement Reporting criteria. It is part of upsize algorithm. It is used as part of event4A configuration: threshold with which the Transport Channel Traffic Volume is compared.
Class 3
Presence required
Visibility customer
Unit bytes
79

Domain RNC
Description It is the size of the averaging not-sliding window used to evaluate the throughput and compare it with the step1Throughputthreshold parameter
Class 3
Presence required
Visibility customer
Unit ms
Domain RNC
Description it is used to determine the level of traffic activity of a user. If the throughput becomes below that threshold, always on timer T1 is started and then potentially, the user radio configuration will be downgraded to always on step 1. Once downsized, this threshold is also used for upsized condition.
Class 3
Presence required
Visibility customer
Unit bit/s
Range [0..32000]

Domain RNC
Description it is used to avoid messaging overflow in case an upgrade from always on step 1 is required. This parameter sets the minimum time between the emission of two events "upgrade required" by the Inode.
Class 3
Presence required
Visibility customer
Unit ms
Domain RNC
Class 3
Presence required
Visibility customer
Unit ms

Description It is used to determine the level of traffic activity of a user that is already in always-on step 1 or simply trafficking if the transition to step 1 is not allowed. If the throughput remains below or equal that threshold during timer T2, user context will be released.
Class 3
Presence required
Visibility customer
Unit bit/s
Range [0..32000]
Domain RNC
Description 25.331 Time to trigger This parameter is part of the Traffic Volume Measurement Reporting criteria. It indicates the period of time between the timing of event detection and the timing of sending Measure- ment Report. It is part of upsize algorithm. It's the period of time during which the condition has be to satisfied before sending a measurement report. In UMTS03, it's used on the event4a reporting.
Class 3
Presence required
Visibility customer
Unit ms
Range 0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000
Initial value 0
82

Class NA
Presence optional
Visibility customer
Range [0..30]

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description this parameter indicates if a time interval must be used to determine the value of the measTraffic- Quant.
Class 3
Presence required
Visibility customer
Unit T.B.D.
Class 3
Presence required
Visibility customer
Initial value rlcBufPayld
Domain RNC
Description TS 25.331 Pending time after trigger Ii indicates the period of time during which it is forbidden to send any new measurement reports with the same Traffic volume event identity even if the triggering condition is fulfilled. It is part of upsize algorithm.
85

Domain RNC
Description TS 25.331 Reporting Threshold This parameter is part of the Traffic Volume Measurement Reporting criteria. It is part of upsize algorithm. It is used as part of event4A configuration: threshold with which the Transport Channel Traffic Volume is compared.
Class 3
Presence required
Visibility customer
Unit bytes
Initial value trafficRepThrs1024

Class 3
Presence required
Visibility customer
Unit ms
Domain RNC
Description This is the threshold of the TRB RLC Buffer occu- pancy that is monitored by the RNC on the downlink for upsized trigger.
Class 3
Presence required
Visibility customer
Unit bytes
Range [0..32000]
Domain RNC
Description it is used to determine the level of traffic activity of a user. If the throughput becomes below that threshold, always on timer T1 is started and then potentially, the user radio configuration will be downgraded to always on step 1.
Class 3
Presence required
Visibility customer
Unit bits/s

Domain RNC
Description it is used to avoid messaging overflow in case an upgrade from always on step 1 is required. This parameter sets the minimum time between the emission of two events "upgrade required" by the Inode.
Class 3
Presence required
Visibility customer
Unit ms
Domain RNC
Class 3
Presence required
Visibility customer
Unit ms

Domain RNC
Description It is used to determine the level of traffic activity of a user that is already in always-on step 1. If the throughput remains below or equal that threshold during timer T2, user context will be released.
Class 3
Presence required
Visibility customer
Unit bit/s
Range [0..32000]
Domain RNC
Description 25.331 Time to trigger This parameter is part of the Traffic Volume Measurement Reporting criteria. It indicates the period of time between the timing of event detection and the timing of sending Measure- ment Report. It is part of upsize algorithm. It's the period of time during which the condition has be to satisfied before sending a measurement report. In UMTS03, it's used on the event4a reporting.
Class 3
Presence required
Visibility customer
Unit ms
Range 0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000
Initial value 0
Domain RNC
Description TS 25.331 This parameter is used in conjunction with the measTrafficQuant. It's conditional on
89

{Average/Variance} selection of the measTraffic- Quant. It corresponds to a time interval used to determine average or variance rlcbuffer. It is part of upsize algorithm.
Class 3
Presence optional
Visibility customer
Unit ms
Initial value N.A.
Domain RNC
Description TS 25.331 Tx interruption after trigger This 3GPP parameter is part of the Traffic Volume Measure- ment Reporting Criteria designated to indicate how long the UE shall block the DTCH transmission on RACH after a measurement report is triggered. It is part of upsize algorithm.
Class 3
Presence required
Visibility customer
Unit ms
90

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description Altitude of cell antenna position above the WGS84 ellipsoid surface. The reference point is the mid- point between all antennas serving one particular sector. .
Class 3
Presence required
Visibility customer
Unit meter
Range [0..10000]
Domain RNC
Description TS 23.032 Position of a site on a map of the world measured as the distance to the North or South of the equator. The expected coded value is calculated from a formula allowing the conversion between the latitude given in degree X and the corresponding integer N: N<= X*2^(23)/90<N+1 except for N=2^(23)-1, for which the range is extended to include N+1.
Class 3
Presence required
Visibility customer
Range [0..8388607]

Description Position of a site on a map of the world in relation to the North or South of the equator.
Class 3
Presence required
Visibility customer
Domain RNC
Description TS 23.032 Position of a site on a map of the world measured as the distance to the East or West of a set line. The expected coded value is calculated from a formula allowing the conversion between the longitude given in degree X (between -180°and 180°) and the corresponding integer N: N<= X*2^(24)/360<N+1
Class 3
Presence required
Visibility customer
Range [-8388608..8388607]
Domain OAM
Class NA
Presence optional
Visibility customer
Range NA

MaxIn- stances
Links:
Parameters:
rdnId

Domain OAM
Description TS23.003 subclause 4.1(release 1999) Mobile Country Code (MCC) identifies the country in which the PLMN is located. The value of the MCC is the same as the three digit MCC contained in interna- tional mobile subscriber identity (IMSI). mobile- CountryCode parameter is a 3 digits BCD-string (each digit is coded on 4 bits, which results finally in a 12 bits-long string).
Class NA
Presence required
Visibility customer
Range [3..3]
Domain OAM
Description TS23.003 subclause 4.1(release 1999) mobileNet- workCode of the network entity Mobile Network Code (MNC) is a code identifying the PLMN in that country. The MNC takes the same value as the two or three digit MNC contained in IMSI. mobileNet- workCode parameter is a 2 or 3 digits BCD-string (each digit is coded on 4 bits, resulting in an 8 or 12 bits-long string).
Class NA
Presence required
Visibility customer
Range [2..3]

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description This attribute provides the RNC IuPriorityLevel associated to the corresponding UMTS TrafficClass- BasedQoS and ARPBasedQoS instances. This attribute is used to retrieve the QoS configuration parameters from the RAB parameters included in the RANAP RabAssignmentRequest received from the Core. Note: 1 is the highest priority.
Class 3
Presence required
Visibility customer
Range [1..15]
Rec val comments
Domain OAM
Class NA
Presence optional
Visibility customer
Range [0..30]

MaxIn- stances
Links:
Parameters:
rdnId
Class NA
Presence required
Visibility customer

Domain RNC
Description Hold-time before activation of the Adaptive Status Filter when transiting from CELL_FACH to CELL_DCH. This timer is to ensure that all data that has been transmitted during CELL_FACH has been flushed as the CFN that has been used to tag the PDU is not consistent between the CELL_FACH and CELL_DCH state.
Class 3
Presence required
Visibility customer
Unit ms
Domain RNC
Description Minimum UE processing time as measured from the radio interface. If, after transmitting or retransmitting a PDU and the RNC RLC receives a request for retransmission from its peer within this interval, the retransmission request is filtered out.
Class 3
Presence required
Visibility customer
Unit ms

MaxIn- stances
Links:
Parameters:
rdnId
Domain RNC
Description Customer application system will perform an FTP to the Performance Server in order to retrieve the stored data. The RNC shall therefore process and feed the "UE RF MEASUREMENT RESULT" to the Performance Server in a timely manner. The results shall be stor
Class NA
Presence required
Visibility customer

Class 0
Presence required
Visibility customer
Unit bytes
Range [0..1024000]
autoFtpTransmitPeriod
autoOmcrFtpDirPath
105

autoOmcrUserId
Class 0
Presence required
Visibility customer
Range [0..40]
autoOmcrUserPasswd
Class 0
Presence required
Visibility customer
Range [0..40]
userSpecificInfo

Child(ren):
MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description It defines the time period for admitted calls based on the RNC overload level
Class 3
Presence required
Visibility customer
Unit s
Range [1..300]
Domain RNC
Description It defines the maximum number of admitted calls in case that RNC reaches Critical overload level
Class 3
Presence required
Visibility customer
Range [0..17000]
Domain RNC
Description It defines the maximum number of admitted calls in case that RNC reaches Major overload level
Class 3
Presence required
Visibility customer

Domain RNC
Description It defines the maximum number of admitted calls in case that RNC reaches minor overload level
Class 3
Presence required
Visibility customer
Range [0..17000]

MaxIn- stances
Links:
shutdownConfClassId RadioAccessService Dedicated- Conf ShutdownConfClass
Parameters:
rdnId
Class NA
Presence required
Visibility customer

Domain RNC
Description One of two radio link load thresholds governing automatic carrier switch off. The combined actual RL load of the base cell and the overlay cell must pass below this threshold for switch Off.
Class 3
Presence required
Visibility customer
Range [0..9999]
Domain RNC
Description One of two power threshold governing automatic carrier switch off. It is given in percentage of the max cell transmit power of the base cell. The combined actual transmit power of base cell and overlay cell must pass below this threshold for switch Off.
Class 3
Presence required
Visibility customer

Domain RNC
Description Threshold used in Radiolink load based formula of ACSO feature. When the measured load exceeds the threshold the overlay cell is switched on.
Class 3
Presence required
Visibility customer
Range [0..9999]
Domain RNC
Description The switch on threshold measured in percentage of max transmit power of the base cell, used in the power based formula of the ACSO feature.When the measured transmit power in the base cell exceeds the threshold the overlay cell is switched on.
Class 3
Presence required
Visibility customer
Domain RNC
Description This choice allows the operator to tailor which formula(s) is (are) used for the Auto Carrier Switch Off feature
Class 3
Presence required
Visibility customer

Initial value RLLoad
Class 3
Presence required
Visibility customer
Range [0..235959]
Description Determins the inertie of the filtering algorithm for automatic carrier switch off. This parameter is used in a forgetting filter algorithm
Class 3
Presence required
Visibility customer
Range 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19
Initial value 11

Description Determins the inertie of the filtering algorithm for automatic carrier switch on. This parameter is used in a forgetting filter algorithm.
Class 3
Presence required
Visibility customer
Range 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19
Initial value 11
Domain RNC
Description Indicates if an alarm shall be generated in case of auto switch off
Class 3
Presence required
Visibility customer
Domain RNC
Description One of two radio link load threshold governing automatic carrier switch off. The actual RL load of the overlay cell must pass below this threshold for switch Off.
Class 3
Presence required
Visibility customer
Range [0..9999]

Domain RNC
Description One of two power threshold governing automatic carrier switch off. It is given in percentage of the max cell transmit power of the base cell. The actual transmit power of the overlay cell must pass below this threshold for switch Off.
Class 3
Presence required
Visibility customer
Range [0..100]
Class 3
Presence required
Visibility customer
Data type ServiceLink
Initial value N.A.
Class 3

Domain OAM
Class NA
Presence optional
Visibility customer
Range [0..30]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for PS HSDPA DL plus EDCHUL.Avg part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]

Domain RNC
Description The weighting to be applied to the average RLs es- tablished for CS SPEECH plus PS DCH plus PS HSDPA part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for CS DATA part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for CS SPEECH plus PS DCH part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]

Domain RNC
Description The weighting to be applied to the average RLs es- tablished for PS HSDPA plus DL DCH plus EDCH UL part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for PS DCH plus PS DCH part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for PS DCH plus PS HSDPA part of the Auto carrier switch off formula
119

Domain RNC
Description The weighting to be applied to the average RLs es- tablished for other part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for signalling part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]

Domain RNC
Description The weighting to be applied for the average number in CELL FACH part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for CS DATA plus PS HSDPA part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for CS Streaming part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer

Domain RNC
Description The weighting to be applied to the average RLs es- tablished for PS DCH DL plus DCH UL part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for PS HSDPA plus DCH UL part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]

Description The weighting to be applied to the average RLs es- tablished for CS SPEECH plus PS DCH plus PS DCH part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for CS SPEECH part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]
Domain RNC
Description The weighting to be applied to the average RLs es- tablished for CS DATA plus PS DCH part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]

Domain RNC
Description The weighting to be applied to the average RLs es- tablished for CS SPEECH and HSDPA part of the Auto carrier switch off formula
Class 3
Presence required
Visibility customer
Range [-64..63]

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description This parameter is used to activate or deactivate the general barring functionality. Deactivation during an overload condition will require time for existing barring to be removed from the cells.
Class 3
Presence required
Visibility customer
Domain RNC
Description This parameter contains the list of classes that need to be excluded from class barring. There are 10 access classes. This parameter needs to define which group of classes can be excluded from barring. Normally no classes are defined as priority classes.
Class 3
Presence required
Visibility customer
Range [10..10]
Description This parameter is used to allow priority access classes
126

Domain RNC
Description This parameter contains the list of classes that can be included in the range. There are 10 access classes. This parameter needs to define which group of classes can be used for barring. Normally all classes are used.
Class 3
Presence required
Visibility customer
Range [10..10]

Child(ren):
MaxIn- stances
Links:
Parameters:
rdnId

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description Indicates the delay to add to the CFN to determine the activation time of the compressed mode. It is given in connection frame number of 10ms
Class 3
Presence required
Visibility customer
Range [0..255]
Domain RNC
Description This parameter indicates the delay to add to the CFN in order to determine the reception time of the NBAP RL Setup Request at NodeB level while the compressed mode is active. It is given in connection frame number of 10ms.
Class 3
Presence required
Visibility customer
Range [0..255]
Domain OAM
Class NA
Presence optional
Visibility customer
Range NA

MaxIn- stances
MaxIn- stances
Links:
Parameters:
rdnId

Description TS 25.331 Downlink Compressed Mode Method Method for generating downlink compressed mode gap
Class 3
Presence required
Visibility customer
Initial value CmodeDlMethodSfdiv2
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >dlCModeMethod=1 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : >dlCModeMethod=1 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Measurement)
134

Domain RNC
Description TS 25.331 Downlink Frame Type Defines if frame type 'A' or 'B' shall be used in downlink compressed mode Type A maximises the transmission gap length and type B is optimised for power control. - With frame structure of type A, the pilot field of the last slot in the transmission gap is transmitted. Transmission is turned off during the rest of the transmission gap (figure 13(a)). -With frame structure of type B, the TPC field of the first slot in the transmission gap and the pilot field of the last slot in the transmission gap is transmitted. Transmission is turned off during the rest of the transmission gap
Class 3
Presence required
Visibility customer
Range CmodeDlFrameTypeA, CmodeDlFrameTypeB
Initial value CmodeDlFrameTypeB
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >dlFrameType= 1 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : >dlFrameType= 1 For the instance 2 corresponding to a Compressed Mode measurement purpose In- terFrequency (Fdd Measurement) > dlFrameType= 1
isPatternAllowed
Domain RNC
Description This parameter allows to use or not the pattern while configuring the compressed mode for a given measurement.
Class 3
Presence required

Rec val comments
Domain RNC
Description TS 25.331 N Identify abort Indicates the maximum number of repeats of patterns that the UE shall use to attempt to decode the unknown BSIC of the GSM cell in the initial BSIC identification procedure
Class 3
Presence optional
Visibility customer
Unit patterns
Range [1..128]
Data type Decimal
Initial value N.A.
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >nIdentifyAbort= N.A. For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : >nIdentifyAbort= 26 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Measurement) > nIdentify- Abort= N.A.
tReconfirmAbort
Domain RNC
Description TS 25.331 T Reconfirm abort Indicates the maximum time allowed for the re-confirmation of the BSIC of one GSM cellin the BSIC re-confirmation procedure
Class 3

Range [0.5..10.0] step:0.5
Data type Decimal
Initial value N.A.
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >tReconfirmAbort= N.A. For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : > tReconfirmAbort= N.A. For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Measurement) > tRecon- firmAbort= N.A.
tgcfnOffset
Domain RNC
Description This parameter is used to determine the TGCFN corresponding to the connection Frame Number of the first frame of the first pattern within the Trans- mission Gap Pattern Sequence, according to the formula: TGCFN=(CmodeDeltaCfn+ TGCFNOffset) mod256
Class 3
Presence required
Visibility customer
Unit frames
Range [0..255]
Data type Decimal
Initial value N.A.
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >tgcfnOffset= 0 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : >tgcfnOffset= 48 For the instance 2 corresponding to a Com- pressed Mode measurement purpose InterFre- quency (Fdd Measurement) > tgcfnOffset= 0
tgd
137

Domain RNC
Description TS 25.331 TGD Transmission gap distance indicates the number of slots between the starting slots of two consecutive transmission gaps within a transmission gap pattern. If there is only one transmission gap in the transmission gap pattern, this parameter shall be set to 0 (0 =undefined).
Class 3
Presence required
Visibility customer
Range [0..269]
Data type Decimal
Initial value 0
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >tgd= 0 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : > tgd= 0 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Measurement) > tgd= 0
tgl1
Domain RNC
Description TS 25.331 TGL1 The length of the first Transmis- sion Gap within the transmission gap pattern expressed in number of slots
Class 3
Presence required
Visibility customer
Range [0..14]
Data type Decimal
Initial value N.A.
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >tgl1= 14 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : > tgl1= 14 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Meas-
138

Domain RNC
Description TS 25.331 TGL2 The length of the second Trans- mission Gap within the transmission gap pattern. If omitted, then TGL2=TGL1, expressed in number of slots. The value 0 means undefined.
Class 3
Presence optional
Visibility customer
Range [0..14]
Data type Decimal
Initial value N.A.
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >tgl2= 0 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : > tgl2= 0 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Meas- urement) > tgl2= 0
tgmp
Description TS 25.331 TGMP Transmission Gap pattern sequence Measurement Purpose.
Class 3
Presence required
Visibility customer
Initial value N.A.
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure-
139

ments : >tgmp= 2 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : >tgmp= 3 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Meas- urement) >tgmp=1
tgpl1
Domain RNC
Description TS 25.331 TGPL1 The duration of transmission gap pattern 1 expressed in number of frames.
Class 3
Presence required
Visibility customer
Unit frames
Range [1..144]
Data type Decimal
Initial value 6
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >tgpl1=6 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : >tgpl1=6 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Meas- urement) > tgpl1=6
tgprc
Domain RNC
Description TS 25.331 TGPRC The number of transmission gap patterns within the Transmission Gap Pattern Se- quence (0=Infinity)
Class 3
Presence required
Visibility customer
Range [1..511]

Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >tgprc= 8 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : > tgprc= 78 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Meas- urement) > tgprc= 50
tgsn
Domain RNC
Description TS 25.331 TGSN Transmission Gap Starting Slot Number The slot number of the first transmission gap slot within the TGCFN.
Class 3
Presence required
Visibility customer
Range [0..14]
Data type Decimal
Initial value N.A.
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >tgsn= 8 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : >tgsn= 8 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Meas- urement) > tgsn= 10
ulCModeMethod
Domain RNC
Description TS 25.331 Uplink compressed mode method Meth- od for generating downlink compressed mode gap
Class 3
Presence required
Visibility customer

Initial value CmodeUlMethodSfdiv2
Def value comments For the instance 0 corresponding to a Compressed Mode measurement purpose GSM RSSI Measure- ments : >ulCModeMethod= 1 For the instance 1 corresponding to a Compressed Mode measurement purpose GSM Initial BSIC Identification : >ulCModeMethod= 1 For the instance 2 corresponding to a Compressed Mode measurement purpose InterFrequency (Fdd Measurement) > ulCMo- deMethod= 1
userSpecificInfo
Domain OAM
Class NA
Presence optional
Visibility customer
Range [0..30]
Rec val comments

MaxIn- stances
Links:
siteName Site

Domain OAM
Description current ipAddress used to contact the Cnode IETF RFC 1208 (IP version 4 source IPV4 @ (internet address is a 32-bit address assigned to hosts using TCP/IP. The synyactic representtaion for a 32-bit integer consists of four 8-bit numbers written in base 10 with periods/dots separating them. Used to represent IP addresses in the Internet as in : 192.67.67.20) used by nodeB in order to communicate with OMC-B
Class NA
Presence required
Visibility customer
Initial value N.A.
Data type Variable[9] List of Enumeration
Initial value N.A.
Domain OAM
Description IETF RFC1208 (IP version 4) Internet address: A 32-bit address assigned to hosts using TCP/IP. The
144

syntactic representation for a 32-bit integer consists of four 8-bit numbers written in base 10 with periods (dots) separating them. Used to represent IP addresses in the Internet as in: 192.67.67.20. IP Ad- dress of the OMUs
Class NA
Presence required
Visibility customer
Initial value N.A.
Domain OAM
Description -MIB Synchronization "On": Configuration modifications are refused by OMC if they cannot be sent to the NE through an Online Command. -MIB Syn- chronization "OFF": Configuration modifications are applied locally by the OMC without sending any command to the NE. This mode is used to prepare an Online Build or Online Creation.
Class NA
Presence required
Visibility customer
Class NA
Presence required
Range NA

Domain OAM
Description System Release managed by the software of the passive OMU
Class NA
Presence required
Visibility customer
Range NA
Domain OAM
Description Alternative IP Address of the second OMU in the Cnode IETF RFC 1208 (IP version 4 IPV4 @ (internet address is a 32-bit address assigned to hosts using TCP/IP. The synyactic representtaion for a 32-bit integer consists of four 8-bit numbers written in base 10 with periods/dots separating them. Used to represent IP addresses in the Inter- net as in : 192.67.67.20) used by nodeB in order to communicate with OMC-B
146

Initial value N.A.
Class NA
Presence optional
Visibility customer
Range Site
Domain OAM
Description it represents the functional level of a Network element
Class NA
Presence required
Visibility customer
Range NA

Domain OAM
Class NA
Presence optional
Visibility customer
Range [0..30]

MaxIn- stances
Links:
Parameters:
rdnId
Class NA
Presence required
Visibility customer

Class NA
Presence required
Range NA

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description This parameter defines the filtering rate for call attempt of CS domain. This parameter type is integer and range is from 0 to 100. And, "0" means that all Initial Direct Transfer (IDT) messages are accepted, i.e this feature is deactivated.
Class 3
Presence required
Visibility customer

MaxIn- stances
Links:
Parameters:
rdnId

Class 3
Presence required
Visibility customer
Range [16..512]
Domain RNC
Description It is the Overload Control Ignore timer as defined in 3GPP 25.413.
Class 3
Presence required
Visibility customer
Unit s
Range [0..65535]
Domain RNC
Description It is the Overload Control Increment timer as defined in 3GPP 25.413.
Class 3
Presence required

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description It is the step sent in the "Number of Step" IE of the RANAP OVERLOAD CONTROL message from RNC to CN when the RNC overload level stays in Critical for another ignoreTimer.
Class 3
Presence required
Visibility customer
Range [0..16]
Domain RNC
Description It is the time period that RNC waits for CN reducing the traffic according to the RANAP OVERLOAD CONTROL message.
Class 3
Presence required
Visibility customer
Unit s
Range [0..65535]
Domain RNC
Description It is the step sent in the "Number of Step" IE of the RANAP OVERLOAD CONTROL message from
157

RNC to CN when the RNC overload level stays in Major for another ignoreTimer.
Class 3
Presence required
Visibility customer
Range [0..16]
Domain RNC
Description It is the step sent in the "Number of Step" IE of RANAP OVERLOAD CONTROL message from RNC to CN when the RNC overload level goes from Major to Critical.
Class 3
Presence required
Visibility customer
Range [0..16]
Domain RNC
Description It is the step sent in the "Number of Step" IE of the RANAP OVERLOAD CONTROL message from RNC to CN when the RNC overload level stays in Minor for another ignoreTimer.
Class 3
Presence required
Visibility customer
Range [0..16]

Domain RNC
Description It is the step sent in the "Number of Step" IE of RANAP OVERLOAD CONTROL message from RNC to CN when the RNC overload level goes from Minor to Critical.
Class 3
Presence required
Visibility customer
Range [0..16]
Domain RNC
Description It is the step sent in the "Number of Step" IE of RANAP OVERLOAD CONTROL message from RNC to CN when the RNC overload level goes from Minor to Major.
Class 3
Presence required
Visibility customer
Range [0..16]
Domain RNC
Description It is the step sent in the "Number of Step" IE of
159

RANAP OVERLOAD CONTROL message from RNC to CN when the RNC overload level goes from OK to Critical.
Class 3
Presence required
Visibility customer
Range [0..16]
Domain RNC
Description It is the step sent in the "Number of Step" IE of RANAP OVERLOAD CONTROL message from RNC to CN when the RNC overload level goes from OK to Major.
Class 3
Presence required
Visibility customer
Range [0..16]
Domain RNC
Description It is the step sent in the "Number of Step" IE of RANAP OVERLOAD CONTROL message from RNC to CN when the RNC overload level goes from OK to Minor.
Class 3
Presence required
Visibility customer
Range [0..16]

MaxIn- stances
Links:
Parameters:
rdnId

Initial value PS_64K
Domain RNC
Description This parameter specifies the max DL bit rate, which may be allocated at service establishment time (RANAP RAB Assignment request) or after a relocation (RANAP Relocation request This parameter is significant for Interactive/background traffic class and taken into account if activation flag of Dl Rb Ad- aptation is TRUE (isDlRbRateAdaptationAllowed of MO RadioAccessService).
Class 3
Presence optional
Visibility customer
Unit Kbits/s
Range [8..2048]
Description This parameter specifies the max UL bit rate, which
163

may be allocated at service establishment time (RANAP RAB Assignment request) or after a relocation (RANAP Relocation request This parameter is significant for Interactive/background traffic class and taken into account if activation flag of Ul Rb Ad- aptation is TRUE (isUlRbRateAdaptationAllowed of MO RadioAccessService).
Class 3
Presence optional
Visibility customer
Unit Kbits/s
Range [8..2048]
Domain RNC
Description TS 25.433 Received total wide band power It corresponds to the received signal strength indicator
Class 3
Presence required
Visibility customer
Unit dBm
Domain RNC
Description The minimum DCH downlink data rate for service triggered data rate downgrade.
Class 3
Presence required
Visibility customer
164

Domain RNC
Description The minimum DCH uplink data rate for service triggered data rate downgrade.
Class 3
Presence required
Visibility customer
Initial value PS_8K
Domain OAM
Description user friendly CacConfClass name, for operator use only (at MMI)
Class NA
Presence required
Visibility customer
Range [0..32]
Domain OAM
165

Child(ren):
MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description This parameter is used to limit the number of simul- taneous user connections being supported by a given Mac-C instance.
Class 3
Presence required
Visibility customer
Range [0..100]
Domain RNC
Description This parameter defines the maximum number of users that can have SRB configuration in CELL_FACH.
Class 3
Presence required
Visibility customer
Range [0..100]
Domain RNC
Description This parameter defines the maximum number of users that can have TRB configuration in CELL_FACH.
Class 3
Presence required
Visibility customer
Range [0..100]

Domain OAM
Class NA
Presence optional
Visibility customer
Range [0..30]

MaxIn- stances
Links:
Parameters:
rdnId

Child(ren):
MaxIn- stances
Links:
Parameters:
rdnId

MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description When CACtransportInfoList has more than one instance then the characteristic indicates what the instance applies to. Most of the time only one instance used with value UNSPECIFIED. Several instances to be used for AMR, to differentiate based on THP, to differentiate interactive from background etc...
Class 3
Presence required
Visibility customer
Initial value UNSPECIFIED
Domain RNC
Description it is the requested bitrate to capture percentage of time the connection is active, the distribution of data rates used and the burstiness of the traffic.
Class 3
Presence required
Visibility customer
Unit bits/s
Range [0..16777216]

Rec val comments
Class 3
Presence required
Visibility customer
Unit bits/s
Range [0..16777216]
Rec val comments
Class 3
Presence required
Visibility customer
Unit bytes
Range [1..65668]

Description This parameter indicates the transport QoS that shall be used for the radio bearer set configuration on Iu interface.
Class 3
Presence required
Visibility customer
Range [0..3]
Domain RNC
Class 3
Presence required
Visibility customer
Unit bits/s
Range [0..16777216]
Rec val comments
Class 3
Presence required
Visibility customer
Unit bits/s

Rec val comments
Domain RNC
Description This parameter indicates the transport QoS that shall be used for the radio bearer set configuration on Iub and Iur interface.
Class 3
Presence required
Visibility customer
Range [0..3]
Class 3
Presence required
Visibility customer
Unit bytes
Range [1..65668]

Domain RNC
Class 3
Presence required
Visibility customer
Unit bits/s
Range [0..16777216]
Rec val comments
Class 3
Presence required
Visibility customer
Unit bits/s
Range [0..16777216]
Rec val comments
Class 3

Child(ren):
MaxIn- stances
Links:
Parameters:
rdnId

Domain RNC
Description This parameter defines the equivalent bit-rate used for the MBMS PTM radio bearer (MTCH) on Iub interface.
Class 3
Presence required
Visibility customer
Unit bits/s
Range [0..16777216]
Domain RNC
Description This parameter defines the maximum bit-rate used for the MBMS PTM radio bearer (MTCH) on Iub interface.
Class 3
Presence required
Visibility customer
Unit bits/s
Range [0..16777216]
Domain RNC
Description This parameter indicates the transport QoS that shall be used for the MBMS PTM radio bearer (MTCH) configuration on Iub interface. Note that this QoS identifier shall correspond to one of the
182

MaxIn- stances
Links:
Parameters:
rdnId
Class NA
Presence required
Visibility customer

Domain RNC
Description The Ec/No delta used by the cNode to trigger the quick repeat
Class 3
Presence required
Visibility customer
Unit dB
Domain RNC
Description The RSCP delta used by the cNode to trigger the quick repeat
Class 3
Presence required
Visibility customer
Unit dBm
Range [-50..50]

Description Enable or disable the ability to increase FACH power while transmitting the rrcConnectionSetup message.
Class 3
Presence required
Visibility customer
Class 3
Presence required
Visibility customer
Description Maximum number of retransmissions of rrcConnec- tionSetup at expiry of t351.
Class 3
Presence required
Visibility customer
Range [0..4]

Class 3
Presence required
Visibility customer
Range [0..10]
Class 3
Presence required
Visibility customer
Range [1..10]
Domain RNC
Description Maximum number of repetitions sent by the cNode to the iNodeRLC
Class 3

Domain RNC
Description Timer to control the retransmission of the rrcCon- nectionSetup in msec.
Class 3
Presence required
Visibility customer
Unit ms
Initial value 700
Recommended value 400
Domain RNC
Description Timer to control the release of UE call context in msec. This timer should match with T300 setting.
Class 3
Presence required
Visibility customer
Unit ms
Range 0, 1000, 1200, 1400, 1600, 1800, 2000, 3000, 4000, 6000, 8000, 10000
Initial value 2000

Rec val comments This timer should match with T300 setting.
Class 3 detail A2
Domain RNC
Description Timer which starts at transmission of RbSetup and stops at reception of RbSetupComplete or Rb- SetupFailure
Class 3
Presence required
Visibility customer
Unit ms
Range [1..15000]
Domain RNC
Description Timer which starts at transmission of ActiveSetUp- date and stops at reception of ActiveSetUpdate- Complete or ActiveSetUpdateFailure. At expiry Re- transmit ActiveSetUpdate and restart timer if V354 <= N354
Class 3
Presence required
Visibility customer
Unit ms
Range [0..10000]

Domain RNC
Description Timer which starts at transmission of ActiveSetUp- date and stops at reception of ActiveSetUpdate- Complete or ActiveSetUpdateFailure
Class 3
Presence required
Visibility customer
Unit ms
Range [1..10000]
Description Timer which starts at transmission of RrcConnec- tionRelease and stops at reception of RrcConnec- tionReleaseComplete
Class 3
Presence required
Visibility customer
Unit ms
Range [1..10000]
Description Timer which starts at transmission of RrcConnec- tionRelease and stops at reception of RrcConnec- tionReleaseComplete
Class 3
Presence required

MaxIn- stances
Links:
Parameters:
rdnId

&nbs

Documents

NN-205~2