NSAI Petroleum Exploration and Extraction Technical Standards … · 2019-01-24 · Petroleum Exploration and Extraction Technical Standards Committee NSAI Standards 1 Swift Square,

Petroleum Exploration and Extraction Technical Standards Committee

NSAI Standards

1 Swift Square, Northwood, Santry, Dublin 9

Page 1 of 42

National Standards Authority of Ireland

NSAI Petroleum Exploration and Extraction Technical Standards

Committee recommended standards selection policy

Issue date: 2013-09-09

The information in this document is correct as July 2013. Standards are continuously being

revised and developed and the editions of the Standards listed are subject to routine

change.


NSAI Standards


Page 2 of 42

Foreword

In response to a request from the Commission of Energy Regulation (CER) the NSAI Petroleum

Exploration and Extraction Technical Standards Committee (PEETSC) has developed this

recommended Standards selection policy document to be applied to petroleum exploration and

extraction activities.

This policy recommendation may assist in fulfilling the CER's obligation to consult NSAI with regard

to the following provisions of the Petroleum (Exploration and Extraction) Safety Act 2010, namely

Sections:

13 H (2) (a),

13 L (2) (a) (i),

13 L (3) (c) and

13 L (3) (d).

Scope

This recommendation sets out a policy that can be applied to petroleum undertakings when

selecting suitable standards to be applied for any petroleum activity licensed under the above Act.

It recognises the extensive number of Standards available and the fact that many new and revised

standards are published every year. It also recognises that, given the nature of the activity, there

cannot be an exhaustive list of suitable standards.

This document provides a list of recommended standards that can be to applied petroleum

exploration and extraction activities.

Legislation

Standards emanating from Standards bodies are not, in themselves, mandatory and only achieve a

mandatory status when referenced in legal instruments.

In all cases legislation takes precedence over any voluntary standard.

When projects to be funded from public funds are to be awarded, those responsible should be

aware of any obligations they may have under public procurement regulations/Directives. For

guidance on this matter the National Procurement Service should be consulted:

http://www.procurement.ie/publications/public-procurement-guidelines-competitive-process

http://www.procurement.ie/publications/public-procurement-guidelines-competitive-process


NSAI Standards


Page 3 of 42

Selection of suitable standards

When selecting suitable specifications for petroleum exploration and extraction activities they

should be selected in order of preference:

1. Irish Standards Specifications (I.S.),

2. NSAI adoptions of European and International Standards,

3. International Standards,

These publications specify minimum requirements for the relevant activity.

In the event that a particular activity, covered by 1 to 3 is addressed more comprehensively in

another publication, undertakings may apply that publication provided that any requirements

contained in 1 to 3 are also met.

In the event that a particular activity is not covered by the above, undertakings can choose to use

publications such as the following:

a. Standards from other National Standards Bodies,

b. Other NSAI publications,

c. Standards from Classification Societies (e.g. Bureau Veritas),

d. Publications from suitable associations (e.g. API).

Rigs and other equipment designed for International use

The PEETSC recognises that the building of equipment such as oil rigs is a truly international activity.

Most rigs are built to meet the expectations of operators active in other national and international

waters. Given this, the selection of standards used to construct/build such equipment cannot,

necessarily follow this policy. However the PEETSC also recognises that such equipment is almost

always built to classification society rules in order to operate to the satisfaction of authorities in

other jurisdictions.

List of suitable standards

The following list is a snapshot (correct on the date of compilation) of identified suitable standards,

in respect to 1 to 3 above, for petroleum exploration and extraction activities. It does not purport to

be a comprehensive list but is a guide to the reader of the types of standards NSAI has recognised as

suitable. This list will be updated from time to time but no less than every two years.

A reference list of publications covering drilling, well construction and well operations is available

from:

http://www.ogp.org.uk/publications/wells-committee/wecstandards/

http://www.ogp.org.uk/publications/wells-committee/wecstandards/


NSAI Standards


Page 4 of 42

Standards in the Oil & Gas industry

The standards listed in this document are recommended as suitable for application in

Ireland. This list is not exhaustive.

Introduction

The majority of Standards referenced in this document have been developed and published by the

International Standards Organisation, ISO, under the Technical Committee ISO/TC 67. Where these

ISO Standards can be adopted by Europe directly without modification then are adopted and

published by the European Committee for Standardisation (CEN) under Technical Committee

CEN/TC 12. Where a modification is required to an ISO Standard CEN/TC 12 publishes the ISO

Standard as a European Standard with its own number and develops the European Standard with

the specific European requirements.

ISO Standards are not automatically adopted as Irish Standards.

European Standards are automatically adopted as Irish Standards.

ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural

gas industries

CEN/TC 12, Materials, equipment and offshore structures for petroleum, petrochemical and natural

gas industries

For standards relating to Explosive atmospheres go to ETCI/TC 6 which mirrors the work of:

CENELEC TC 31 - Electrical apparatus for potentially explosive atmospheres, and

IEC TC 31 - Equipment for explosive atmospheres

Explanation of Standard designations

A Standard is a document that provides requirements, specifications, guidelines or characteristics

that can be used consistently to ensure that materials, products, processes and services are fit for

their purpose.

Typical Standard references

I.S. 123 Irish Standard developed and published by NSAI

S.R. 123 Irish Standard Recommendation published by NSAI

EN 12345 European Standard published by CEN/CENELEC

ISO 12345 International Standard published by ISO

IEC 60125 International Standard published by IEC

I.S. EN 12345 European Standard adopted as an Irish Standard

EN ISO 12345 ISO Standard adopted as a European Standard

I.S. EN ISO 12345 European Standard adopted as an Irish Standard

http://www.etci.ie/technical/tc6.html


NSAI Standards


Page 5 of 42

I.S. ISO 12345 ISO Standard adopted as an Irish Standard

A Technical Specification is a document for which there is the future possibility of agreement on a

European Standard, but for which at present:

the required support for approval as a Standard cannot be obtained,

there is doubt on whether consensus has been achieved,

the subject matter is still under technical development, or

there is another reason precluding immediate publication as a Standard.

A Technical Specification is not allowed to conflict with an existing European Standard.

Typical Technical Specification references

CEN/TS 12345 Technical Specification published by CEN

ISO/TS 12345 Technical Specification published by ISO

CEN ISO/TS 12345 ISO Technical Specification adopted as a European Technical Specification

S.R. CEN ISO/TS 12345 European Technical Specification adopted as an Irish Standard Recommendation

A Technical Report is a document containing informative material not suitable to be published as a

Standard or a Technical Specification. A TR can include, for example, data obtained from a survey

carried out among the national members, data on work in other organizations or data on the state of

the art in relation to national standards on a particular subject.

Typical Technical Report references

CEN/TR 12345 Technical Report published by CEN

S.R. CEN/TR 12345 CEN Technical Report adopted as an Irish Standard Recommendation

ISO/TR 12345 Technical Report published by ISO

CEN ISO/TR 12345 ISO Technical Report adopted as a European Technical Report

S.R. CEN ISO/TR 12345 European Technical Report adopted as an Irish Standard Recommendation

List of Irish National Standards and International Standard for the Oilfield

The information in the following tables is correct as of 13th September 2012. Standards are

continuously being revised and developed and the edition of the Standards listed are subject to

routine change.

The list of Standards has been separated into 7 sections. Standards can be used in the various

sections as appropriate.


NSAI Standards


Page 6 of 42

Key:

1 Down hole

2 Subsea drilling and production equipment

3 Surface drilling, production and processing equipment and systems

4 Offshore structures (Semi submercibles)

5 Offshore structures (Platforms and jackets)

6 Pipeline transportation systems

7 Onshore processing


NSAI Standards


Page 7 of 42

1 Down hole

Standards listed are from:

ISO/TC 67/SC 4 – Drilling and production equipment

ISO TC 67/SC 5 - Casing, tubing and drill pipe

Standard Number Standard Title

S.R. CEN ISO/TR 10400:2011 Petroleum and natural gas industries - Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing (ISO/TR 10400:2007)

I.S. EN ISO 10405:2006 Petroleum and natural gas industries - Care and use of casing and tubing (ISO 10405:2006)

ISO 10407:1993 Petroleum and natural gas industries -- Drilling and production equipment -- Drill stem design and operating limits

I.S. EN ISO 10407-2:2008 Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Inspection and classification of used drill stem elements (ISO 10407-2:2008)

I.S. EN ISO 10414-1:2008 Petroleum and natural gas industries - Field testing of drilling fluids - Part 1: Water-based fluids (ISO 10414-1:2008)

I.S. EN ISO 10414-2:2011 Petroleum and natural gas industries - Field testing of drilling fluids - Part 2: Oil-based fluids (ISO 10414-2:2011)

I.S. EN ISO 10416:2009 Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO 10416:2008)

I.S. EN ISO 10417:2004 Petroleum and natural gas industries - Subsurface safety valve systems - Design, installation, operation and redress (ISO 10417:2004)

I.S. EN ISO 10424-1:2004 Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements (ISO 10424-1:2004)

I.S. EN ISO 10424-2:2007 Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Threading and gauging of rotary shouldered thread connections (ISO 10424-2:2007)

I.S. EN ISO 10426-1:2009 Petroleum and natural gas industries - Cements and materials for well cementing - Part 1: Specification (ISO 10426-1:2009)

I.S. EN ISO 10426-2:2003 Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements (ISO 10426-2:2003)

I.S. EN ISO 10426-3:2004 Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations (ISO 10426-3:2003)

I.S. EN ISO 10426-4:2004 Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure (ISO 10426-4:2004)

I.S. EN ISO 10426-5:2005 Petroleum and natural gas industries - Cements and materials for well cementing - Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure (ISO 10426-5:2004)

I.S. EN ISO 10426-6:2008 Petroleum and natural gas industries - Cements and materials for well cementing - Part 6: Methods for determining the static gel strength of cement formulations (ISO 10426-6:2008)

I.S. EN ISO 10427-1:2001 Petroleum and natural gas industries - Casing centralizers - Part 1: Bow-spring casing centralizers (ISO 10427-1:2001)

I.S. EN ISO 10427-2:2004 Petroleum and natural gas industries - Equipment for well cementing - Part 2: Centralizer placement and stop-collar testing (ISO 10427-2:2004)


NSAI Standards


Page 8 of 42

I.S. EN ISO 10427-3:2004 Petroleum and natural gas industries - Equipment for well cementing - Part 3: Performance testing of cementing float equipment (ISO 10427-3:2003)

I.S. EN ISO 10432:2004 Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment (ISO 10432:2004)

I.S. EN ISO 11960:2011 Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells (ISO 11960:2011)

I.S. EN ISO 11961:2008 Petroleum and natural gas industries - Steel drill pipe (ISO 11961:2008)

I.S. EN ISO 13500:2008 Petroleum and natural gas industries - Drilling fluid materials - Specifications and tests (ISO 13500:2008)

I.S. EN ISO 13501:2011 Petroleum and natural gas industries - Drilling fluids - Processing equipment evaluation (ISO 13501:2011)

I.S. EN ISO 13503-1:2011 Petroleum and natural gas industries - Completion fluids and materials - Part 1: Measurement of viscous properties of completion fluids (ISO 13503-1:2011)

I.S. EN ISO 13503-2:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations (ISO 13503-2:2006)

I.S. EN ISO 13503-3:2005 Petroleum and natural gas industries - Completion fluids and materials - Part 3: Testing of heavy brines (ISO 13503-3:2005)

I.S. EN ISO 13503-4:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 4: Procedure for measuring stimulation and gravel-pack fluid leakoff under static conditions (ISO 13503-4:2006)

I.S. EN ISO 13503-5:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 5: Procedures for measuring the long-term conductivity of proppants (ISO 13503-5:2006)

I.S. EN ISO 13678:2012 Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements (ISO 13678:2010)

I.S. EN ISO 13679:2006 Petroleum and natural gas industries - Procedures for testing casing and tubing connections (ISO 13679:2002)

I.S. EN ISO 13680:2010 Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)

I.S. EN ISO 14310:2008 Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs (ISO 14310:2008)

I.S. EN ISO 15136-1:2009 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 1: Pumps (ISO 15136-1:2009)

I.S. EN ISO 15136-2:2006 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 2: Surface-drive systems (ISO 15136-2:2006)

I.S. EN ISO 15463:2003 Petroleum and natural gas industries - Field inspection of new casing, tubing and plain-end drill pipe (ISO 15463:2003)

I.S. EN ISO 15546:2011 Petroleum and natural gas industries - Aluminium alloy drill pipe (ISO 15546:2011)

I.S. EN ISO 16070:2005 Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples (ISO 16070:2005)

I.S. EN ISO 17078-1:2004 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels (ISO 17078-1:2004)

I.S. EN ISO 17078-2:2007 Petroleum and natural gas industries - Drilling and production equipment - Part 2: Flow-control devices for side-pocket mandrels (ISO 17078-2:2007)

I.S. EN ISO 17078-3:2009 Petroleum and natural gas industries - Drilling and production equipment - Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket


NSAI Standards


Page 9 of 42

mandrels (ISO 17078-3:2009)

I.S. EN ISO 17078-4:2010 Petroleum and natural gas industries - Drilling and production equipment - Part 4: Practices for side-pocket mandrels and related equipment (ISO 17078-4:2010)

ISO 17824:2009 Petroleum and natural gas industries -- Downhole equipment -- Sand screens

I.S. EN ISO 28781:2010 Petroleum and natural gas industries - Drilling and production equipment - Subsurface barrier valves and related equipment (ISO 28781:2010)


NSAI Standards


Page 10 of 42

2 Subsea drilling and production equipment




I.S. EN ISO 13628-1:2005 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations (ISO 13628-1:2005)

I.S. EN ISO 13628-2:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Unbonded flexible pipe systems for subsea and marine applications (ISO 13628-2:2006)

I.S. EN ISO 13628-3:2000 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 3: Through flowline (TFL) systems (ISO 13628-3:2000)

I.S. EN ISO 13628-4:2010 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 4: Subsea wellhead and tree equipment (ISO 13628-4:2010)

I.S. EN ISO 13628-5:2009 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals (ISO 13628-5:2009)

I.S. EN ISO 13628-6:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 6: Subsea production control systems (ISO 13628-6:2006)

I.S. EN ISO 13628-7:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 7: Completion/workover riser systems (ISO 13628-7:2005)

I.S. EN ISO 13628-8:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems (ISO 13628-8:2002)

I.S. EN ISO 13628-9:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 9: Remotely Operated Tool (ROT) intervention systems (ISO 13628-9:2000)

I.S. EN ISO 13628-10:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for bonded flexible pipe (ISO 13628-10:2006)

I.S. EN ISO 13628-11:2008 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe systems for subsea and marine applications (ISO 13628-11:2007)

I.S. EN ISO 13628-15:2011 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 15: Subsea structures and manifolds (ISO 13628-15:2011)


NSAI Standards


Page 11 of 42

3 Surface drilling, production and processing equipment and systems


ISO/TC 67


ISO TC 67/SC 6 - Processing equipment and systems


I.S. EN ISO 10418:2003 Petroleum and natural gas industries - Offshore production installations - Basic surface process safety systems (ISO 10418:2003)

I.S. EN ISO 10423:2009 Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment (ISO 10423:2009)

I.S. EN ISO 13533:2001 Petroleum and natural gas industries - Drilling and production equipment - Drill-through equipment (ISO 13533:2001)

I.S. EN ISO 13534:2000 Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and remanufacture of hoisting equipment (ISO 13534:2000)

I.S. EN ISO 13535:2000 Petroleum and natural gas industries - Drilling and production equipment - Hoisting equipment (ISO 13535:2000)

I.S. EN ISO 13626:2004 Petroleum and natural gas industries - Drilling and production equipment - Drilling and well-servicing structures (ISO 13626:2003)

I.S. EN ISO 13702:1999 Petroleum and natural gas industries - Control and migration of fires and explosions on offshore production installations - Requirements and guidelines (ISO 13702:1999)

I.S. EN ISO 13703:2000 Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO 13703:2000)

I.S. EN ISO 14224:2006 Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for equipment (ISO 14224:2006)

I.S. EN ISO 14692-1:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2002)

I.S. EN ISO 14692-2:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002)

I.S. EN ISO 14692-3:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2002)

I.S. EN ISO 14692-4:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2002)

I.S. EN ISO 14693:2003 Petroleum and natural gas industries - Drilling and well-servicing equipment (ISO 14693:2003)

I.S. EN ISO 15138:2007 Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning (ISO 15138:2007)

I.S. EN ISO 15156-1:2009 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 1: General principles for selection of cracking-resistant materials (ISO 15156-1:2009)

I.S. EN ISO 15156-2:2009 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons (ISO 15156-2:2009)

I.S. EN ISO 15156-3:2009 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs


NSAI Standards


Page 12 of 42

(corrosion-resistant alloys) and other alloys (ISO 15156-3:2009)

I.S. EN ISO 15544:2010 Petroleum and natural gas industries - Offshore production installations - Requirements and guidelines for emergency response (ISO 15544:2000, including Amd 1:2009)

I.S. EN ISO 15663-1:2006 Petroleum and natural gas industries - Life cycle costing - Part 1: Methodology (ISO 15663-1:2000)

ISO 15663-2:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 2: Guidance on application of methodology and calculation methods

ISO 15663-3:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 3: Implementation guidelines

I.S. EN ISO 17776:2002 Petroleum and natural gas industries - Offshore production installations - Guidelines on tools and techniques for hazard identification and risk assessment (ISO 17776:2000)

I.S. EN ISO 20815:2010 Petroleum, petrochemical and natural gas industries - Production assurance and reliability management (ISO 20815:2008, Corrected version 2009-06-15)

I.S. EN ISO 21457:2010 Petroleum, petrochemical and natural gas industries -- Materials selection and corrosion control for oil and gas production systems

S.R. CEN ISO/TS 27469:2011 Petroleum, petrochemical and natural gas industries - Method of test for fire dampers (ISO/TS 27469:2010)

I.S. EN ISO 27509:2012 Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2012)

S.R. CEN ISO/TS 29001:2011 Petroleum, petrochemical and natural gas industries - Sector-specific quality management systems - Requirements for product and service supply organizations (ISO/TS 29001:2010)


NSAI Standards


Page 13 of 42

4 Offshore structures (Semi submersibles and jack-ups)



ISO/TC 67/SC 7 – Offshore structures


I.S. EN ISO 13624-1:2009 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Design and operation of marine drilling riser equipment (ISO 13624-1:2009)

ISO/TR 13624-2:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Deepwater drilling riser methodologies, operations, and integrity technical report

I.S. EN ISO 13625:2002 Petroleum and natural gas industries - Drilling and production equipment - Marine drilling riser couplings (ISO 13625:2002)

I.S. EN ISO 19901-7:2005 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units (ISO 19901-7:2005)

I.S. EN ISO 19904-1:2006 Petroleum and natural gas industries - Floating offshore structures - Part 1: Monohulls, semi-submersibles and spars (ISO 19904-1:2006)

I.S. EN ISO 19905-1:2012 Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 1: Jack-ups (ISO 19905-1:2012)


NSAI Standards


Page 14 of 42

5 Offshore structures (Platforms and jackets)



ISO/TC 67/SC 7 – Offshore structures


I.S. EN ISO 19900:2002 Petroleum and natural gas industries - General requirements for offshore structures (ISO 19900:2002)

I.S. EN ISO 19901-1:2005 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design and operating considerations (ISO 19901-1:2005)

I.S. EN ISO 19901-2:2004 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 2: Seismic design procedures and criteria (ISO 19901-2:2004)

I.S. EN ISO 19901-3:2010 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 3: Topsides structure (ISO 19901-3:2010)

I.S. EN ISO 19901-4:2003 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 4: Geotechnical and foundation design considerations (ISO 19901-4:2003)

I.S. EN ISO 19901-5:2003 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 5: Weight control during engineering and construction (ISO 19901-5:2003)

I.S. EN ISO 19901-6:2009 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 6: Marine operations (ISO 19901-6:2009)

I.S. EN ISO 19901-7:2005 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units (ISO 19901-7:2005)

I.S. EN ISO 19902:2007 Petroleum and natural gas industries - Fixed steel offshore structures (ISO 19902:2007)

I.S. EN ISO 19903:2006 Petroleum and natural gas industries - Fixed concrete offshore structures (ISO 19903:2006)

I.S. EN ISO 19906:2010 Petroleum and natural gas industries - Arctic offshore structures (ISO 19906:2010)


NSAI Standards


Page 15 of 42

6 Pipeline transportation systems


CEN ECISS/TC 110 - Steel tubes, and iron and steel fittings

CEN/TC 12 - Materials, equipment and offshore structures for petroleum, petrochemical and natural

gas industries

ISO/TC 67/SC 2 - Pipeline transportation systems


I.S. ISO 3183:2012 Petroleum and natural gas industries - Steel pipe for pipeline transportation systems

ISO 12490:2011 Petroleum and natural gas industries -- Mechanical integrity and sizing of actuators and mounting kits for pipeline valves

ISO/TS 12747:2011 Petroleum and natural gas industries -- Pipeline transportation systems -- Recommended practice for pipeline life extension

I.S. EN 14161:2011 Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2009 modified)

I.S. EN 14163:2001 Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000 modified)

I.S. EN 13942:2009 Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified)

I.S. EN ISO 14723:2009 Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2009)

ISO 15589-1:2003 Petroleum and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 1: On-land pipelines

ISO 15589-2:2012 Petroleum, petrochemical and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 2: Offshore pipelines

I.S. EN 14870-1:2011 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2009 modified)

I.S. EN 14870-2:2004 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings (ISO 15590-2:2003 modified)

I.S. EN 14870-3:2006 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges (ISO 15590-3:2004, modified)

I.S. EN ISO 16708:2006 Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods (ISO 16708:2006)

I.S. EN ISO 21329:2004 Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors (ISO 21329:2004)

I.S. EN ISO 21809-2:2007 Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 2: Fusion-bonded epoxy coatings (ISO 21809-2:2007)

ISO 21809-3:2008 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 3: Field joint coatings

ISO 21809-4:2009 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 4: Polyethylene coatings (2-layer PE)

I.S. EN ISO 21809-5:2010 Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 5: External


NSAI Standards


Page 16 of 42

concrete coatings (ISO 21809-5:2010)

7. Onshore processing


ISO/TC 60/SC 2 – Gears - Gear capacity calculation


ISO/TC 67/SC 6 – Processing equipment and systems

ISO/TC 115/SC 3 – Pumps - Installation and special application

ISO/TC 118/SC 1 – Compressors and pneumatic tools, machines and equipment- Process

compressors

ISO/TC 153/SC 1 – Valves - Design, manufacture, marking and testing

ISO/TC 192 – Gas turbines

CEN/TC 69 – Industrial valves


I.S. EN ISO 3977-5:2003 Gas turbines - Procurement - Part 5: Applications for petroleum and natural gas industries (ISO 3977-5:2001)

ISO 10428:1993 Petroleum and natural gas industries -- Sucker rods (pony rods, polished rods, couplings and sub-couplings) -- Specification

ISO 10431:1993 Petroleum and natural gas industries -- Pumping units -- Specification

I.S. EN ISO 10434:2004 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries (ISO 10434:2004)

I.S. EN ISO 10437:2003 Petroleum, petrochemical and natural gas industries - Steam turbines - Special-purpose applications (ISO 10437:2003)

I.S. EN ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements (ISO 10438-1:2007)

I.S. EN ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems (ISO 10438-2:2007)

I.S. EN ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2007)

I.S. EN ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 4: Self-acting gas seal support systems (ISO 10438-4:2007)

I.S. EN ISO 10439:2002 Petroleum, chemical and gas service industries - Centrifugal compressors (ISO 10439:2002)

I.S. EN ISO 10440-1:2007 Petroleum, petrochemical and natural gas industries - Rotary-type positive-displacement compressors - Part 1: Process compressors (ISO 10440-1:2007)

I.S. EN ISO 10440-2:2001 Petroleum and natural gas industries - Rotary-type positive-displacement


NSAI Standards


Page 17 of 42

compressors - Part 2: Packaged air compressors (oil-free) (ISO 10440-2:2001)

I.S. EN ISO 10441:2007 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007)

I.S. EN ISO 10442:2002 Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002)

I.S. EN ISO 13631:2002 Petroleum and natural gas industries - Packaged reciprocating gas compressors (ISO 13631:2002)

I.S. EN ISO 13691:2002 Petroleum and natural gas industries - High-speed special-purpose gear units (ISO 13691:2001)

I.S. EN ISO 13704:2007 Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries (ISO 13704:2007)

I.S. EN ISO 13705:2012 Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service (ISO 13705:2012)

I.S. EN ISO 13706:2011 Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2011)

I.S. EN ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009)

I.S. EN ISO 13710:2004 Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps (ISO 13710:2004)

I.S. EN ISO 14691:2008 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General-purpose applications (ISO 14691:2008)

I.S. EN ISO 15547-1:2005 Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat exchangers (ISO 15547-1:2005)

I.S. EN ISO 15547-2:2005 Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 2: Brazed aluminium plate-fin heat exchangers (ISO 15547-2:2005)

S.R. CEN/TR 14549:2004 Guide to the use of ISO 15649 and ANSI/ASME B31.3 for piping in Europe in compliance with the Pressure Equipment Directive

I.S. EN ISO 15761:2002 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries (ISO 15761:2002)

I.S. EN ISO 16812:2007 Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers (ISO 16812:2007)

I.S. EN ISO 17292:2004 Metal ball valves for petroleum, petrochemical and allied industries (ISO 17292:2004)

I.S. EN ISO 21049:2004 Pumps - Shaft sealing systems for centrifugal and rotary pumps (ISO 21049:2004)

I.S. EN ISO 23251:2007 Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems (ISO 23251:2006)

I.S. EN ISO 23936-1:2009 Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and gas production - Part 1: Thermoplastics (ISO 23936-1:2009)

S.R. CEN ISO/TS 24817:2011 Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO/TS 24817:2006)

I.S. EN ISO 25457:2008 Petroleum, petrochemical and natural gas industries - Flare details for general refinery and petrochemical service (ISO 25457:2008)

I.S. EN ISO 28300:2008 Petroleum, petrochemical and natural gas industries - Venting of


NSAI Standards


Page 18 of 42

atmospheric and low-pressure storage tanks (ISO 28300:2008)

ISO\TC 60 Gears

Secretariat: ANSI

Secretary: Mr. Charlie Fischer

Chairperson: Mr. William A. Bradley (USA) until end 2014

ISO Central Secretariat contact: M. Franck Perrad

Creation date: 1947

Scope ISO/TC 60:

Standardization in the field of gears, including terminology, nominal dimensions, tolerances,

and tools for manufacturing and control.

Total number of published ISO standards related to the TC and its SCs (number includes

updates):

68

Number of published ISO standards under the direct responsibility of TC 60 (number

includes updates):

28

(P) Participating countries: 15

(O) Observing countries: 23

Irelands membership status -

Subcommittees of ISO/TC 60:

TC 60/SC 1 Nomenclature and wormgearing

TC 60/SC 2 Gear capacity calculation

Working Groups of ISO/TC 60:

TC 60/JWG 1 Joint ISO/TC 60-IEC/TC 88 WG: Wind turbine gearboxes

TC 60/WG 2 Accuracy of gears

ISO /TC 60/SC 2: ISO Standards published and referenced in this document

ISO 13691:2001 Petroleum and natural gas industries -- Content and drafting of a functional specification


NSAI Standards


Page 19 of 42

ISO/TC 67

Title: Materials, equipment and offshore structures for petroleum, petrochemical and natural gas

industries

Secretariat: NEN

Secretary: Mr. Harold Pauwels

Chairperson: Mr. Andries Otter

ISO Central Secretariat contact: Mrs. Kirsi Silander

Creation date: 1947

Scope of ISO/TC 67:

Standardization of the materials, equipment and offshore structures used in the drilling, production,

transport by pipelines and processing of liquid and gaseous hydrocarbons within the petroleum,

petrochemical and natural gas industries.

Excluded from the scope are aspects of offshore structures subject to IMO requirements (ISO / TC 8).

Total number of published ISO standards related to the TC and its SCs (number

includes updates):

181


includes updates):

18



Irelands membership status O


Irelands membership status

TC 67/SC 2 Pipeline transportation systems P

TC 67/SC 3 Drilling and completion fluids, and well cements -

TC 67/SC 4 Drilling and production equipment -

TC 67/SC 5 Casing, tubing and drill pipe -

TC 67/SC 6 Processing equipment and systems -

http://www.iso.org/iso/home/standards_development/list_of_iso_technical_committees/technical_committee_contact.htm?commid=49506

mailto:[email protected]

mailto:[email protected]

http://www.iso.org/iso/home/store/catalogue_tc/catalogue_tc_browse.htm?commid=49506&published=on&includesc=true

http://www.iso.org/iso/home/store/catalogue_tc/catalogue_tc_browse.htm?commid=49506&published=on

http://www.iso.org/iso/home/standards_development/list_of_iso_technical_committees/iso_technical_committee_participation.htm?commid=49506

http://www.iso.org/iso/home/standards_development/list_of_iso_technical_committees/iso_technical_committee_participation.htm?commid=49506

http://www.iso.org/iso/home/standards_development/list_of_iso_technical_committees/iso_technical_committee.htm?commid=49532






NSAI Standards


Page 20 of 42

TC 67/SC 7 Offshore structures -

TC 67/SC 8 Arctic operations -


TC 67/EC/MC Executive committee and Management committee

TC 67/WG 2 Conformity assessment

TC 67/WG 4 Reliability Engineering and technology

TC 67/WG 5 Aluminium alloy pipes

TC 67/WG 7 Corrosion resistant materials

TC 67/WG 8 Materials, corrosion control, welding and jointing, and non-destructive

examination (NDE)

TC 67/WG 10 Liquefied Natural Gas (LNG) installations and equipment

TC 67/WG 11 Coating and lining of structures and equipment

TC 67/WG 12 CO2 aspects

ISO /TC 67: ISO Standards published

ISO 13879:1999 Petroleum and natural gas industries -- Content and drafting of a functional specification

ISO 13880:1999 Petroleum and natural gas industries -- Content and drafting of a technical specification

ISO/TR 13881:2000 Petroleum and natural gas industries -- Classification and conformity assessment of products, processes and services

ISO 14224:2006 Petroleum, petrochemical and natural gas industries -- Collection and exchange of reliability and maintenance data for equipment

ISO 15156-1:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 1: General principles for selection of cracking-resistant materials

ISO 15156-2:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons

ISO 15156-3:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys

ISO 15546:2011




NSAI Standards


Page 21 of 42

Petroleum and natural gas industries -- Aluminium alloy drill pipe

ISO 15663-1:2000 Petroleum and natural gas industries -- Life cycle costing -- Part 1: Methodology

ISO 15663-2:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 2: Guidance on application of methodology and calculation methods

ISO 15663-3:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 3: Implementation guidelines

ISO 20312:2011 Petroleum and natural gas industries -- Design and operating limits of drill strings with aluminium alloy components

ISO 20815:2008 Petroleum, petrochemical and natural gas industries -- Production assurance and reliability management

ISO 21457:2010 Petroleum, petrochemical and natural gas industries -- Materials selection and corrosion control for oil and gas production systems

ISO 23936-1:2009 Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 1: Thermoplastics

ISO 23936-2:2011 Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 2: Elastomers

ISO 28460:2010 Petroleum and natural gas industries -- Installation and equipment for liquefied natural gas -- Ship-to-shore interface and port operations

ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries -- Sector-specific quality management systems -- Requirements for product and service supply organizations


NSAI Standards


Page 22 of 42

ISO/TC 67/SC 2 - Pipeline transportation systems

Secretariat: UNI

Twinned secretariat: SAC

Secretary: Mr Giuliano Corbella

Twinned secretary: Mr. Changyi Qin

Chairperson: Mr. Denis Tikhomirov until end 2013


Number of published ISO standards under the direct responsibility of TC 67/SC 2 (number

includes updates):

23



Irelands membership status P

ISO 3183:2012 Petroleum and natural gas industries -- Steel pipe for pipeline transportation systems

ISO 12490:2011 Petroleum and natural gas industries -- Mechanical integrity and sizing of actuators and mounting kits for pipeline valves

ISO/TS 12747:2011 Petroleum and natural gas industries -- Pipeline transportation systems -- Recommended practice for pipeline life extension

ISO 13623:2009 Petroleum and natural gas industries -- Pipeline transportation systems

ISO 13847:2000 Petroleum and natural gas industries -- Pipeline transportation systems -- Welding of pipelines

ISO 13847:2000/Cor 1:2001

ISO 14313:2007 Petroleum and natural gas industries -- Pipeline transportation systems -- Pipeline valves

ISO 14313:2007/Cor 1:2009

ISO 14723:2009 Petroleum and natural gas industries -- Pipeline transportation systems -- Subsea pipeline valves

ISO 15589-1:2003 Petroleum and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 1: On-land pipelines

ISO 15589-2:2012 Petroleum, petrochemical and natural gas industries -- Cathodic protection of pipeline transportation systems --


NSAI Standards


Page 23 of 42

Part 2: Offshore pipelines

ISO 15590-1:2009 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 1: Induction bends

ISO 15590-2:2003 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 2: Fittings

ISO 15590-3:2004 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 3: Flanges

ISO 16708:2006 Petroleum and natural gas industries -- Pipeline transportation systems -- Reliability-based limit state methods

ISO 21329:2004 Petroleum and natural gas industries -- Pipeline transportation systems -- Test procedures for mechanical connectors

ISO 21809-1:2011 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 1: Polyolefin coatings (3-layer PE and 3-layer PP)

ISO 21809-2:2007 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 2: Fusion-bonded epoxy coatings

ISO 21809-2:2007/Cor 1:2008

ISO 21809-3:2008 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 3: Field joint coatings

ISO 21809-3:2008/Amd 1:2011

ISO 21809-4:2009 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 4: Polyethylene coatings (2-layer PE)

ISO 21809-5:2010 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 5: External concrete coatings


NSAI Standards


Page 24 of 42

ISO/TC 67/SC 3 - Drilling and completion fluids, and well cements

Secretariat: SN

Secretary: Mr Øivind Bråthen

Chairperson: Mr. Roger Tønnessen (Norway) until end 2011



includes updates):

27




ISO 10414-1:2008 Petroleum and natural gas industries -- Field testing of drilling fluids -- Part 1: Water-based fluids

ISO 10414-2:2011 Petroleum and natural gas industries -- Field testing of drilling fluids -- Part 2: Oil-based fluids

ISO 10416:2008 Petroleum and natural gas industries -- Drilling fluids -- Laboratory testing

ISO 10426-1:2009 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 1: Specification

ISO 10426-1:2009/Cor 1:2010

ISO 10426-1:2009/Cor 2:2012

ISO 10426-2:2003 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 2: Testing of well cements

ISO 10426-2:2003/Cor 1:2006

ISO 10426-2:2003/Amd 1:2005 Water-wetting capability testing

ISO 10426-3:2003 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 3: Testing of deepwater well cement formulations

ISO 10426-4:2004 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure

ISO 10426-5:2004 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure


NSAI Standards


Page 25 of 42

ISO 10426-6:2008 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 6: Methods for determining the static gel strength of cement formulations

ISO 10427-1:2001 Petroleum and natural gas industries -- Equipment for well cementing -- Part 1: Casing bow-spring centralizers

ISO 10427-2:2004 Petroleum and natural gas industries -- Equipment for well cementing -- Part 2: Centralizer placement and stop-collar testing

ISO 10427-3:2003 Petroleum and natural gas industries -- Equipment for well cementing -- Part 3: Performance testing of cementing float equipment

ISO 13500:2008 Petroleum and natural gas industries -- Drilling fluid materials -- Specifications and tests

ISO 13500:2008/Cor 1:2009

ISO 13500:2008/Amd 1:2010 Barite 4,1

ISO 13501:2011 Petroleum and natural gas industries -- Drilling fluids -- Processing equipment evaluation

ISO 13503-1:2011 Petroleum and natural gas industries -- Completion fluids and materials -- Part 1: Measurement of viscous properties of completion fluids

ISO 13503-2:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations

ISO 13503-2:2006/Amd 1:2009 Addition of Annex B: Proppand specification

ISO 13503-3:2005 Petroleum and natural gas industries -- Completion fluids and materials -- Part 3: Testing of heavy brines

ISO 13503-3:2005/Cor 1:2006

ISO 13503-4:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 4: Procedure for measuring stimulation and gravel-pack fluid leak off under static conditions

ISO 13503-5:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 5: Procedures for measuring the long-term conductivity of proppants


NSAI Standards


Page 26 of 42

ISO/TC 67/SC 4 - Drilling and production equipment

Secretariat: ANSI

Secretary: Dr. Edmund Baniak

Chairperson: Dr. Austin Freeman (USA) until end 2013



includes updates):

48




ISO 10407:1993 Petroleum and natural gas industries -- Drilling and production equipment -- Drill stem design and operating limits

ISO 10407-2:2008 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 2: Inspection and classification of used drill stem elements

ISO 10407-2:2008/Cor 1:2009

ISO 10417:2004 Petroleum and natural gas industries -- Subsurface safety valve systems -- Design, installation, operation and redress

ISO 10423:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Wellhead and christmas tree equipment

ISO 10424-1:2004 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 1: Rotary drill stem elements

ISO 10424-2:2007 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 2: Threading and gauging of rotary shouldered thread connections

ISO 10428:1993 Petroleum and natural gas industries -- Sucker rods (pony rods, polished rods, couplings and sub-couplings) -- Specification

ISO 10431:1993 Petroleum and natural gas industries -- Pumping units -- Specification

ISO 10432:2004 Petroleum and natural gas industries -- Downhole equipment -- Subsurface safety valve equipment

ISO 13533:2001 Petroleum and natural gas industries -- Drilling and production equipment -- Drill-through equipment


NSAI Standards


Page 27 of 42

ISO 13533:2001/Cor 1:2005

ISO 13534:2000 Petroleum and natural gas industries -- Drilling and production equipment -- Inspection, maintenance, repair and remanufacture of hoisting equipment

ISO 13535:2000 Petroleum and natural gas industries -- Drilling and production equipment -- Hoisting equipment

ISO 13624-1:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 1: Design and operation of marine drilling riser equipment

ISO/TR 13624-2:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Deepwater drilling riser methodologies, operations, and integrity technical report

ISO 13625:2002 Petroleum and natural gas industries -- Drilling and production equipment -- Marine drilling riser couplings

ISO 13626:2003 Petroleum and natural gas industries -- Drilling and production equipment -- Drilling and well-servicing structures

ISO 13628-1:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 1: General requirements and recommendations

ISO 13628-1:2005/Amd 1:2010 Revised Clause 6

ISO 13628-2:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 2: Unbonded flexible pipe systems for subsea and marine applications

ISO 13628-2:2006/Cor 1:2009

ISO 13628-3:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 3: Through flowline (TFL) systems

ISO 13628-4:2010 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 4: Subsea wellhead and tree equipment

ISO 13628-4:2010/Cor 1:2011

ISO 13628-5:2009 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 5: Subsea umbilicals

ISO 13628-6:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 6: Subsea production control systems

ISO 13628-7:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 7: Completion/workover riser systems

ISO 13628-8:2002 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 8: Remotely


NSAI Standards


Page 28 of 42

Operated Vehicle (ROV) interfaces on subsea production systems

ISO 13628-8:2002/Cor 1:2005

ISO 13628-9:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 9: Remotely Operated Tool (ROT) intervention systems

ISO 13628-10:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 10: Specification for bonded flexible pipe

ISO 13628-11:2007 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 11: Flexible pipe systems for subsea and marine applications

ISO 13628-11:2007/Cor 1:2008

ISO 13628-15:2011 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 15: Subsea structures and manifolds

ISO 14310:2008 Petroleum and natural gas industries -- Downhole equipment -- Packers and bridge plugs

ISO 14693:2003 Petroleum and natural gas industries -- Drilling and well-servicing equipment

ISO 15136-1:2009 Petroleum and natural gas industries -- Progressing cavity pump systems for artificial lift -- Part 1: Pumps

ISO 15136-2:2006 Petroleum and natural gas industries -- Progressing cavity pump systems for artificial lift -- Part 2: Surface-drive systems

ISO 16070:2005 Petroleum and natural gas industries -- Downhole equipment -- Lock mandrels and landing nipples

ISO 17078-1:2004 Petroleum and natural gas industries -- Drilling and production equipment -- Part 1: Side-pocket mandrels

ISO 17078-1:2004/Amd 1:2010

ISO 17078-2:2007 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Flow-control devices for side-pocket mandrels

ISO 17078-2:2007/Cor 1:2009

ISO 17078-3:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels

ISO 17078-4:2010 Petroleum and natural gas industries -- Drilling and production equipment -- Part 4: Practices for side-pocket mandrels and related equipment

ISO 17824:2009 Petroleum and natural gas industries -- Downhole equipment -- Sand screens


NSAI Standards


Page 29 of 42

ISO 28781:2010 Petroleum and natural gas industries -- Drilling and production equipment --Subsurface barrier valves and related equipment

ISO/TC 67/SC 5 - Casing, tubing and drill pipe

Secretariat: JISC

Secretary: Mr. Tsunehiro Ise

Chairperson: Mr. Yoshi Kusaka (Japan) until end 2011



includes updates):

10




ISO/TR 10400:2007 Petroleum and natural gas industries -- Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing

ISO 10405:2000 Petroleum and natural gas industries -- Care and use of casing and tubing

ISO 11960:2011 Petroleum and natural gas industries -- Steel pipes for use as casing or tubing for wells

ISO 11961:2008 Petroleum and natural gas industries -- Steel drill pipe

ISO 11961:2008/Cor 1:2009

ISO 13678:2010 Petroleum and natural gas industries -- Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements

ISO 13679:2002 Petroleum and natural gas industries -- Procedures for testing casing and tubing connections

ISO 13680:2010 Petroleum and natural gas industries -- Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock -- Technical delivery conditions

ISO 15463:2003 Petroleum and natural gas industries -- Field inspection of new casing, tubing and plain-end drill pipe

ISO 15463:2003/Cor 1:2009


NSAI Standards


Page 30 of 42

ISO/TC 67/SC 6 - Processing equipment and systems

Secretariat: AFNOR

Secretary: Mme Alice Jubeau

Chairperson: M. Joël Fort (France) until end 2014



includes updates):

41




ISO 10418:2003 Petroleum and natural gas industries -- Offshore production installations -- Analysis, design, installation and testing of basic surface process safety systems

ISO 10418:2003/Cor 1:2008

ISO 10437:2003 Petroleum, petrochemical and natural gas industries -- Steam turbines -- Special-purpose applications

ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 1: General requirements

ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 2: Special-purpose oil systems

ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 3: General-purpose oil systems

ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 4: Self-acting gas seal support systems

ISO 10441:2007 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- Special-purpose applications

ISO 12211:2012 Petroleum, petrochemical and natural gas industries -- Spiral plate heat exchangers

ISO 12212:2012 Petroleum, petrochemical and natural gas industries -- Hairpin-type heat exchangers

ISO 13702:1999 Petroleum and natural gas industries -- Control and mitigation of fires and explosions on offshore production


NSAI Standards


Page 31 of 42

installations -- Requirements and guidelines

ISO 13703:2000 Petroleum and natural gas industries -- Design and installation of piping systems on offshore production platforms

ISO 13703:2000/Cor 1:2002

ISO 13704:2007 Petroleum, petrochemical and natural gas industries -- Calculation of heater-tube thickness in petroleum refineries

ISO 13704:2007/Cor 1:2008

ISO 13705:2012 Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service

ISO 13706:2011 Petroleum, petrochemical and natural gas industries -- Air-cooled heat exchangers

ISO 14691:2008 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- General-purpose applications

ISO 14692-1:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 1: Vocabulary, symbols, applications and materials

ISO 14692-2:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 2: Qualification and manufacture

ISO 14692-2:2002/Cor 1:2005

ISO 14692-3:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 3: System design

ISO 14692-3:2002/Cor 1:2005

ISO 14692-4:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 4: Fabrication, installation and operation

ISO 14692-4:2002/Cor 1:2006

ISO 15138:2007 Petroleum and natural gas industries -- Offshore production installations -- Heating, ventilation and air-conditioning

ISO 15544:2000 Petroleum and natural gas industries -- Offshore production installations -- Requirements and guidelines for emergency response

ISO 15544:2000/Amd 1:2009

ISO 15547-1:2005 Petroleum, petrochemical and natural gas industries -- Plate-type heat exchangers -- Part 1: Plate-and-frame heat exchangers

ISO 15547-2:2005


NSAI Standards


Page 32 of 42

Petroleum, petrochemical and natural gas industries -- Plate-type heat exchangers -- Part 2: Brazed aluminium plate-fin heat exchangers

ISO 15649:2001 Petroleum and natural gas industries -- Piping

ISO 16812:2007 Petroleum, petrochemical and natural gas industries -- Shell-and-tube heat exchangers

ISO 17776:2000 Petroleum and natural gas industries -- Offshore production installations -- Guidelines on tools and techniques for hazard identification and risk assessment

ISO 23251:2006 Petroleum, petrochemical and natural gas industries -- Pressure-relieving and depressuring systems

ISO 23251:2006/Cor 1:2007

ISO 23251:2006/Amd 1:2008

ISO/TS 24817:2006 Petroleum, petrochemical and natural gas industries -- Composite repairs for pipework -- Qualification and design, installation, testing and inspection

ISO 25457:2008 Petroleum, petrochemical and natural gas industries -- Flare details for general refinery and petrochemical service

ISO/TS 27469:2010 Petroleum, petrochemical and natural gas industries - Method of test for fire dampers

ISO 28300:2008 Petroleum, petrochemical and natural gas industries -- Venting of atmospheric and low-pressure storage tanks

ISO 28300:2008/Cor 1:2009

ISO/TC 67/SC 7 - Offshore structures

Secretariat: BSI

Secretary: Dr. Charles A. Whitlock

Chairperson: Mr. Philip Smedley (United Kingdom) until end 2013



includes updates):

14





NSAI Standards


Page 33 of 42

ISO 19900:2002 Petroleum and natural gas industries -- General requirements for offshore structures

ISO 19901-1:2005 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 1: Metocean design and operating considerations

ISO 19901-2:2004 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 2: Seismic design procedures and criteria

ISO 19901-3:2010 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 3: Topsides structure

ISO 19901-4:2003 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 4: Geotechnical and foundation design considerations

ISO 19901-5:2003 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 5: Weight control during engineering and construction

ISO 19901-6:2009 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 6: Marine operations

ISO 19901-6:2009/Cor 1:2011

ISO 19901-7:2005 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units

ISO 19902:2007 Petroleum and natural gas industries -- Fixed steel offshore structures

ISO 19903:2006 Petroleum and natural gas industries -- Fixed concrete offshore structures

ISO 19904-1:2006 Petroleum and natural gas industries -- Floating offshore structures -- Part 1: Monohulls, semi-submersibles and spars

ISO 19905-1:2012 Petroleum and natural gas industries -- Site-specific assessment of mobile offshore units -- Part 1: Jack-ups

ISO 19906:2010 Petroleum and natural gas industries -- Arctic offshore structures

ISO/TC 67/SC 8 Arctic operations

Secretariat: GOST R

Secretary: Mrs. Liudmila Zalevskaya

Chairperson: Mr. Mikhail Rusakov until end 2017


Creation date: 2011


NSAI Standards


Page 34 of 42


includes updates):

0




ISO/TC 115 - Pumps

Secretariat: AFNOR

Secretary: M. Jacques Amaraggi

Chairperson: M. René-André Barbarulo (France) until end 2012


Creation date: 1964

Scope of ISO/TC 115:

Standardization in the field of pumps; including:

dimensions and technical specifications,

test methods and conditions of acceptance for rotodynamic and positive displacement pumps

for all liquids, including complete pumping installations,

installations and special applications, as well as rotodynamic mixers for waste water


updates):

24


includes updates):

4





NSAI Standards


Page 35 of 42



TC 115/SC 1 Dimensions and technical specifications of pumps -

TC 115/SC 2 Methods of measurement and testing -

TC 115/SC 3 Installation and special application -


TC 115/WG 7 Pumping system energy assessment

ISO/TC 115/SC 3: ISO Standards published and referenced in this document

ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries

ISO 13710:2004 Petroleum, petrochemical and natural gas industries -- Reciprocating positive displacement pumps

ISO 21049:2004 Pumps -- Shaft sealing systems for centrifugal and rotary pumps

ISO/TC 118 - Compressors and pneumatic tools, machines and equipment

Secretariat: SIS

Secretary: Ms Lena Fagervall

Chairperson: Mrs. Jenny Buck (United Kingdom) until end 2013


Creation date: 1965


Standardization in the field of:

air compressors;

compressors for the process, petroleum, chemical and gas industry services;

pneumatic tools and machines;

compressed air purity specification and compressed air treatment equipment.

Excluded from the scope are pneumatic tool shanks and tool fitting dimensions, as they fall within

the scope of ISO / TC 29.


NSAI Standards


Page 36 of 42


updates):

68






TC 118/SC 1 Process compressors `-

TC 118/SC 3 Pneumatic tools and machines -

TC 118/SC 4 Compressed air purity specification and compressed air treatment

equipment

-

TC 118/SC 6 Air compressors and compressed air systems -

There are no Working Groups within ISO/TC 118.


ISO 10439:2002 Petroleum, chemical and gas service industries -- Centrifugal compressors

ISO 10440-1:2007 Petroleum, petrochemical and natural gas industries -- Rotary-type positive-displacement compressors -- Part 1: Process compressors

ISO 10440-2:2001 Petroleum and natural gas industries -- Rotary-type positive-displacement compressors -- Part 2: Packaged air compressors (oil-free)

ISO 10442:2002 Petroleum, chemical and gas service industries -- Packaged, integrally geared centrifugal air compressors

ISO 13631:2002 Petroleum and natural gas industries -- Packaged reciprocating gas compressors


NSAI Standards


Page 37 of 42

ISO/TC 153 - Valves

Secretariat: vacant

Secretary:

Chairperson: vacant


Creation date: 1971


Standardization in the field of industrial valves and steam traps. The standardization to include

parameters covering interchangeability, valve mating details for actuator mounting, testing,

marking, quality requirements, terminology and other relevant parameters.

Excluded from the scope are:

safety and relief valves and other pressure relief devices which are the responsibility of

ISO/TC 185;

production valves for wellhead equipment and valves for cross country pipelines for the

petroleum and natural gas industries which are the responsibility of ISO/TC 67;

valves forming the final control element used for industrial process control systems which are

the responsibility of IEC/TC 65;

valves having an envelope predominantly made of plastics which are the responsibility of

ISO/TC 138;

valves for sanitary use.


updates):

25


includes updates):

8






TC 153/SC 1 Design, manufacture, marking and testing -

TC 153/SC 2 Valve actuator attachment -


NSAI Standards


Page 38 of 42

There are no Working Groups within ISO/TC 153.


ISO 10434:2004 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries

ISO 15761:2002 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries

ISO 17292:2004 Metal ball valves for petroleum, petrochemical and allied industries

ISO/TC 192 - Gas turbines

Secretariat: ANSI

Secretary: Mr. Robin Proctor

Chairperson: Mr. Benjamin Wiant (USA) until end 2013


Creation date: 1988


Standardization in the field of all aspects of gas turbine design, application, installation, operation

and maintenance, including simple turbine cycles, combined cycle systems, definitions,

procurement, acceptance, performance, environment (on the gas turbine itself and the external

environment) and methods of test.

ISO/TC 192 is responsible for preparing horizontal standards for all types of gas turbines. Work on

aero gas turbine engines shall be undertaken in liaison with those technique committees having the

primary responsability.

Note: ISO/TC 20 has the primary responsibility of preparing standards relative to the specific

application of gas turbines to aerospace.


updates):

16


includes updates):

16

Participating countries: 14

Observing countries: 12



NSAI Standards


Page 39 of 42

There are no Subcommittees within ISO/TC 192.


TC 192/WG 3 Combined cycles

TC 192/WG 4 Joint TC 192-TC 67/SC 6 WG : Gas turbine

TC 192/WG 7 Fuels, environment

TC 192/WG 8 Trend monitoring systems

TC 192/WG 9 Electric power applications

TC 192/WG 10 Gas turbine safety

TC 192/WG 11 Acceptance tests

TC 192/WG 12 Microturbines

TC 192/WG 13 Cogeneration systems

ISO/TC 192: ISO Standards published and referenced in this document

ISO 3977-5:2001 Gas turbines -- Procurement -- Part 5: Applications for petroleum and natural gas industries

This ISO Standard has been adopted by CEN/TC 12


NSAI Standards


Page 40 of 42

CEN/TC 12 - Materials, equipment and offshore structures for petroleum, petrochemical and

natural gas industries

Status: Active

Secretariat: AFNOR

Secretary: Ms A. Jubeau ([email protected])

Chairperson: Mr G. Trican (FR)

CCMC PM: Mrs M. Poidevin

There are no Working Groups in this Technical Committee.

This Technical Committee mirrors the work of ISO/TC 67 at a European level and adopts, were

appropriate, ISO Standards as European Standards.

Where modification have been made to ISO Standards they have been published by the Technical

Committee as separate European Standards.

CEN/TC 12 Standards published and referenced in this documentEN

14163:2001

Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000 modified)

EN 14870-2:2004 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings (ISO 15590-2:2003 modified)

EN 14870-3:2006 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges (ISO 15590-3:2004, modified)

CEN/TR 14549:2004 Guide to the use of ISO 15649 and ANSI/ASME B31.3 for piping in Europe in compliance with the Pressure Equipment Directive

EN 13942:2009 Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified)


NSAI Standards


Page 41 of 42

CEN/TC 69 – Industrial valves

Status: Active

Secretariat: AFNOR

Secretary: Ms H.Cros ([email protected])

Chairperson: Mr P.Vinzio (FR)

CCMC PM: Mr T. Legrand

Scope: The standardization of valves for all industrial applications and for all types of fluids,

including : - steam traps; - valve actuator interface; - safety devices against excessive pressure

(safety valves and bursting disks); - control valves (excluding the actuator element and their

interface); but excluding: - sanitary valves (as defined by CEN/TC 164/WG 8).

CEN/TC 69/WG 1 Basic standards

CEN/TC 69/WG 4 Butterfly valves

CEN/TC 69/WG 5 Plug and ball valves

CEN/TC 69/WG 6 Check valves

CEN/TC 69/WG 8 Valves for liquified natural gas and for the distribution of natural gas

CEN/TC 69/WG 9 Valves for the transport of petroleum and natural gas

CEN/TC 69/WG 10 Safety devices against excessive pressure

CEN/TC 69/WG 12 Valves for the process industry

CEN/TC 69/WG 14 Fire hydrants

CEN/TC 69/WG 16 Plastic valves

CEN/TC 69/WG 17 Metallic and thermoplastic valves for water supply


NSAI Standards


Page 42 of 42

CEN ECISS/TC 110 - Steel tubes, and iron and steel fittings

Status: Active

Secretariat: UNI

Secretary: Mr V.Vergani ([email protected])

Chairperson: Mr R.Zanetti (IT)

CCMC PM: Mr A. Da Costa

Scope: Standardization of technical delivery conditions for steel tubes and iron and steel fittings for

steel tubes for all applications. Included are the metallic and organic coatings, threading (including

gauging) and mechanical and non-destructive testing. Excluded are design, calculation and testing of

metallic piping systems, flanges and hollow sections

Working Groups of ECISS/TC 110:

ECISS/TC 110/WG 1 Tubes for pressure purposes

ECISS/TC 110/WG 2 Line pipe

ECISS/TC 110/WG 3 Fittings

ECISS/TC 110/WG 4 Coatings for steel tubes

ECISS/TC 110/WG 5 Tube for the conveyance of aqueous liquids

ECISS/TC 110/WG 6 Tube threads and service tubes

ECISS/TC 110/WG 7 Dimensions and tolerances

ECISS/TC 110/WG 8 Mechanical testing of tubes

ECISS/TC 110/WG 9 Non-destructive testing

ECISS/TC 110/WG 10 Tubes for mechanical and general engineering purposes

CEN ECISS/TC 110 Standards published and referenced in this document EN ISO 3183:2012

Petroleum and natural gas industries - Steel pipe for pipeline transportation systems (ISO 3183:2012)

Documents

NSAI Petroleum Exploration and Extraction Technical Standards … · 2019-01-24 · Petroleum Exploration and Extraction Technical Standards Committee NSAI Standards 1 Swift Square,