Nulon Chain Lube · Nulon Products Australia Chemwatch Hazard Alert Code: 4 Nulon Chain Lube Chemwatch: 86-2660 ... Removal of contact lenses after an eye injury should only be undertaken

Nulon Products Australia Chemwatch Hazard Alert Code: 4

Nulon Chain Lube

Chemwatch: 86-2660Version No: 3.1.1.1Safety Data Sheet according to WHS and ADG requirements

Issue Date: 01/11/2019Print Date: 05/07/2020

S.GHS.AUS.EN

SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING

Product Identifier

Product name Nulon Chain Lube

Synonyms Product Code: NCL

Proper shipping name AEROSOLS

Other means ofidentification Not Available

Relevant identified uses of the substance or mixture and uses advised against

Relevant identified usesGrease Industrial and non-industrial sprayingApplication is by spray atomisation from a hand held aerosol packUse according to manufacturer's directions.

Details of the supplier of the safety data sheet

Registered company name Nulon Products Australia Nulon Products NZ (Nulon NZ Ltd.)

Address 17 Yulong Close Moorebank NSW 2170 Australia 80 Queen Street Auckland Central 1010 New Zealand

Telephone +61 2 9608 7800 0800 454 108

Fax +61 2 9601 4700 +61 2 9601 4700

Website Not Available Not Available

Email [email protected] Not Available

Emergency telephone number

Association / Organisation Chemwatch 24hr. Chemwatch 24hr. CHEMWATCH EMERGENCYRESPONSE

Emergency telephonenumbers 1800 039 008 +800 2436 2255 +61 1800 951 288

Other emergencytelephone numbers Not Available Not Available +61 2 9186 1132

Once connected and if the message is not in your prefered language then please dial 01

SECTION 2 HAZARDS IDENTIFICATION

Classification of the substance or mixture

Poisons Schedule Not Applicable

Classification [1] Flammable Aerosols Category 1, Specific target organ toxicity - single exposure Category 3 (narcotic effects), Aspiration HazardCategory 1, Chronic Aquatic Hazard Category 3

Legend:1. Classified by Chemwatch; 2. Classification drawn from HCIS; 3. Classification drawn from Regulation (EU) No 1272/2008 -Annex VI

Label elements

Hazard pictogram(s)

Emergency telephone number 0800 154 166 (24 hr)

SIGNAL WORD DANGER

Hazard statement(s)

H222 Extremely flammable aerosol.

H336 May cause drowsiness or dizziness.

H304 May be fatal if swallowed and enters airways.

H412 Harmful to aquatic life with long lasting effects.

AUH044 Risk of explosion if heated under confinement.

Precautionary statement(s) Prevention

P210 Keep away from heat/sparks/open flames/hot surfaces. - No smoking.

P211 Do not spray on an open flame or other ignition source.

P251 Pressurized container: Do not pierce or burn, even after use.

P271 Use only outdoors or in a well-ventilated area.

Precautionary statement(s) Response

P301+P310 IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.

P331 Do NOT induce vomiting.

P312 Call a POISON CENTER or doctor/physician if you feel unwell.

P304+P340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.

Precautionary statement(s) Storage

P405 Store locked up.

P410+P412 Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.

P403+P233 Store in a well-ventilated place. Keep container tightly closed.

Precautionary statement(s) Disposal

P501 Dispose of contents/container to authorised hazardous or special waste collection point in accordance with any local regulation.

SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS

SubstancesSee section below for composition of Mixtures

MixturesCAS No %[weight] Name

109-66-0 10-<25

64742-48-9. 10-<25

Not Available balance Ingredients determined not to be hazardous

106-97-8. 25-<50

74-98-6 2.5-<10

SECTION 4 FIRST AID MEASURES

Description of first aid measures

Eye Contact

If aerosols come in contact with the eyes: Immediately hold the eyelids apart and flush the eye continuously for at least 15 minutes with fresh running water. Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionallylifting the upper and lower lids. Transport to hospital or doctor without delay. Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.

Skin Contact

If solids or aerosol mists are deposited upon the skin:Flush skin and hair with running water (and soap if available). Remove any adhering solids with industrial skin cleansing cream. DO NOT use solvents. Seek medical attention in the event of irritation.

Inhalation

If aerosols, fumes or combustion products are inhaled:Remove to fresh air. Lay patient down. Keep warm and rested. Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiating first aidprocedures.

n-pentane

naphtha petroleum, isoparaffin, hydrotreated

butane

propane

If breathing is shallow or has stopped, ensure clear airway and apply resuscitation, preferably with a demand valveresuscitator, bag-valve mask device, or pocket mask as trained. Perform CPR if necessary. Transport to hospital, or doctor.

Ingestion

Avoid giving milk or oils. Avoid giving alcohol.

Not considered a normal route of entry.If spontaneous vomiting appears imminent or occurs, hold patient's head down, lower than their hips to help avoid possibleaspiration of vomitus.

Indication of any immediate medical attention and special treatment neededFor acute or short term repeated exposures to petroleum distillates or related hydrocarbons:

Primary threat to life, from pure petroleum distillate ingestion and/or inhalation, is respiratory failure. Patients should be quickly evaluated for signs of respiratory distress (e.g. cyanosis, tachypnoea, intercostal retraction, obtundation) and given oxygen. Patientswith inadequate tidal volumes or poor arterial blood gases (pO2 50 mm Hg) should be intubated. Arrhythmias complicate some hydrocarbon ingestion and/or inhalation and electrocardiographic evidence of myocardial injury has been reported; intravenouslines and cardiac monitors should be established in obviously symptomatic patients. The lungs excrete inhaled solvents, so that hyperventilation improvesclearance. A chest x-ray should be taken immediately after stabilisation of breathing and circulation to document aspiration and detect the presence of pneumothorax. Epinephrine (adrenalin) is not recommended for treatment of bronchospasm because of potential myocardial sensitisation to catecholamines. Inhaledcardioselective bronchodilators (e.g. Alupent, Salbutamol) are the preferred agents, with aminophylline a second choice. Lavage is indicated in patients who require decontamination; ensure use of cuffed endotracheal tube in adult patients. [Ellenhorn and Barceloux: MedicalToxicology]

Treat symptomatically.

SECTION 5 FIREFIGHTING MEASURES

Extinguishing mediaSMALL FIRE:

Water spray, dry chemical or CO2 LARGE FIRE:

Water spray or fog. Do not use a water jet to fight fire.

Special hazards arising from the substrate or mixture

Fire Incompatibility Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition mayresult

Advice for firefighters

Fire Fighting

Alert Fire Brigade and tell them location and nature of hazard. May be violently or explosively reactive. Wear breathing apparatus plus protective gloves. Prevent, by any means available, spillage from entering drains or water course.

Fire/Explosion Hazard

Liquid and vapour are highly flammable. Severe fire hazard when exposed to heat or flame. Vapour forms an explosive mixture with air. Severe explosion hazard, in the form of vapour, when exposed to flame or spark.

Combustion products include:carbon dioxide (CO2)other pyrolysis products typical of burning organic material.Contains low boiling substance: Closed containers may rupture due to pressure buildup under fire conditions.carbon monoxide (CO)

HAZCHEM Not Applicable

SECTION 6 ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency proceduresSee section 8

Environmental precautionsSee section 12

Methods and material for containment and cleaning up

Minor Spills

Clean up all spills immediately. Avoid breathing vapours and contact with skin and eyes. Wear protective clothing, impervious gloves and safety glasses. Shut off all possible sources of ignition and increase ventilation.

Major Spills

Clear area of personnel and move upwind. Alert Fire Brigade and tell them location and nature of hazard. May be violently or explosively reactive. Wear breathing apparatus plus protective gloves.

Clear area of all unprotected personnel and move upwind. Alert Emergency Authority and advise them of the location and nature of hazard. May be violently or explosively reactive. Wear full body clothing with breathing apparatus.

Personal Protective Equipment advice is contained in Section 8 of the SDS.

SECTION 7 HANDLING AND STORAGE

Precautions for safe handling

Safe handling

The conductivity of this material may make it a static accumulator., A liquid is typically considered nonconductive if itsconductivity is below 100 pS/m and is considered semi-conductive if its conductivity is below 10 000 pS/m., Whether a liquid isnonconductive or semi-conductive, the precautions are the same., A number of factors, for example liquid temperature, presenceof contaminants, and anti-static additives can greatly influence the conductivity of a liquid.

Avoid all personal contact, including inhalation. Wear protective clothing when risk of exposure occurs. Use in a well-ventilated area. Prevent concentration in hollows and sumps.

Other information Keep dry to avoid corrosion of cans. Corrosion may result in container perforation and internal pressure may eject contents ofcan

Conditions for safe storage, including any incompatibilities

Suitable container Aerosol dispenser. Check that containers are clearly labelled.

Storage incompatibility Avoid reaction with oxidising agents

SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION

Control parameters

OCCUPATIONAL EXPOSURE LIMITS (OEL)

INGREDIENT DATA

Source Ingredient Material name TWA STEL Peak Notes

Australia ExposureStandards n-pentane Pentane 600 ppm / 1770

mg/m32210 mg/m3 /750 ppm

NotAvailable

NotAvailable

Australia ExposureStandards

naphtha petroleum, isoparaffin,hydrotreated

Oil mist, refinedmineral 5 mg/m3 Not Available Not

AvailableNotAvailable

Australia ExposureStandards butane Butane 800 ppm / 1900

mg/m3 Not Available NotAvailable

NotAvailable

EMERGENCY LIMITS

Ingredient Material name TEEL-1 TEEL-2 TEEL-3

n-pentane Pentane, n- 3000*ppm

33000***ppm

200000***ppm

naphtha petroleum,isoparaffin, hydrotreated Naphtha, hydrotreated heavy; (Isopar L-rev 2) 350

mg/m31,800mg/m3

40,000mg/m3

naphtha petroleum,isoparaffin, hydrotreated

Petroleum distillates; petroleum ether; includes clay-treated light naphthenic[64742-45-6]; low boiling [68477-31-6]; petroleum extracts [64742-06-9]; petroleumbase oil [64742-46-7]; petroleum 50 thinner, petroleum spirits [64475-85-0], Soltrol,VM&P naphtha [8032-32-4]; Ligroine, and paint solvent; petroleum paraffins C5-C20[64771-72-8]; hydrotreated light naphthenic [64742-53-6]; solvent refined lightnaphthenic [64741-97-5]; and machine coolant 1

1,100mg/m3

1,800mg/m3

40,000mg/m3

butane Butane NotAvailable

NotAvailable

NotAvailable

propane Propane NotAvailable

NotAvailable

NotAvailable

Ingredient Original IDLH Revised IDLH

n-pentane 1,500 ppm Not Available

naphtha petroleum,isoparaffin, hydrotreated 2,500 mg/m3 Not Available

butane Not Available 1,600 ppm

propane 2,100 ppm Not Available

Exposure controls

Appropriate engineeringcontrols

Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designedengineering controls can be highly effective in protecting workers and will typically be independent of worker interactions toprovide this high level of protection.The basic types of engineering controls are:Process controls which involve changing the way a job activity or process is done to reduce the risk.Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilationthat strategically "adds" and "removes" air in the work environment.

Personal protection

Eye and face protection

Safety glasses with side shields.Chemical goggles.Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policydocument, describing the wearing of lenses or restrictions on use, should be created for each workplace or task.

No special equipment for minor exposure i.e. when handling small quantities.OTHERWISE: For potentially moderate or heavy exposures:

Safety glasses with side shields. NOTE: Contact lenses pose a special hazard; soft lenses may absorb irritants and ALL lenses concentrate them. Close fitting gas tight goggles

DO NOT wear contact lenses.Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policydocument, describing the wearing of lens or restrictions on use, should be created for each workplace or task. This shouldinclude a review of lens absorption and adsorption for the class of chemicals in use and an account of injury experience.Medical and first-aid personnel should be trained in their removal and suitable equipment should be readily available.

Skin protection See Hand protection below

Hands/feet protection

No special equipment needed when handling small quantities. OTHERWISE: For potentially moderate exposures: Wear general protective gloves, eg. light weight rubber gloves. For potentially heavy exposures: Wear chemical protective gloves, eg. PVC. and safety footwear.

Body protection See Other protection below

Other protection

No special equipment needed when handling small quantities.OTHERWISE:

Overalls. Skin cleansing cream. Eyewash unit. The clothing worn by process operators insulated from earth may develop static charges far higher (up to 100 times) than theminimum ignition energies for various flammable gas-air mixtures. This holds true for a wide range of clothing materialsincluding cotton. Avoid dangerous levels of charge by ensuring a low resistivity of the surface material worn outermost.

BRETHERICK: Handbook of Reactive Chemical Hazards.

Recommended material(s)GLOVE SELECTION INDEX

Respiratory protectionType AX Filter of sufficient capacity. (AS/NZS 1716 & 1715, EN 143:2000 &149:2001, ANSI Z88 or national equivalent)

Where the concentration of gas/particulates in the breathing zone, approachesor exceeds the "Exposure Standard" (or ES), respiratory protection is required.Degree of protection varies with both face-piece and Class of filter; the natureof protection varies with Type of filter.

Required MinimumProtection Factor

Half-FaceRespirator

Full-FaceRespirator

Powered AirRespirator

up to 10 x ES AX-AUS - AX-PAPR-AUS /Class 1

up to 50 x ES - AX-AUS /Class 1 -

up to 100 x ES - AX-2 AX-PAPR-2 ^

^ - Full-faceA(All classes) = Organic vapours, B AUS or B1 = Acid gasses, B2 = Acid gasor hydrogen cyanide(HCN), B3 = Acid gas or hydrogen cyanide(HCN), E =Sulfur dioxide(SO2), G = Agricultural chemicals, K = Ammonia(NH3), Hg =Mercury, NO = Oxides of nitrogen, MB = Methyl bromide, AX = Low boilingpoint organic compounds(below 65 degC)

Cartridge respirators should never be used for emergency ingress or inareas of unknown vapour concentrations or oxygen content.The wearer must be warned to leave the contaminated area immediatelyon detecting any odours through the respirator. The odour may indicate thatthe mask is not functioning properly, that the vapour concentration is toohigh, or that the mask is not properly fitted. Because of these limitations,

Glove selection is based on a modified presentation of the: "Forsberg Clothing Performance Index". The effect(s) of the following substance(s) are taken into account in the computer-generated selection: Nulon Chain Lube

Material CPI

PVA A

VITON A

NITRILE B

NEOPRENE C

NEOPRENE/NATURAL C

NITRILE+PVC C

PVC C

* CPI - Chemwatch Performance IndexA: Best SelectionB: Satisfactory; may degrade after 4 hours continuous immersionC: Poor to Dangerous Choice for other than short term immersionNOTE: As a series of factors will influence the actual performance of the glove,a final selection must be based on detailed observation. -* Where the glove is to be used on a short term, casual or infrequent basis,factors such as "feel" or convenience (e.g. disposability), may dictate a choiceof gloves which might otherwise be unsuitable following long-term or frequentuse. A qualified practitioner should be consulted.

only restricted use of cartridge respirators is considered appropriate.Cartridge performance is affected by humidity. Cartridges should bechanged after 2 hr of continuous use unless it is determined that thehumidity is less than 75%, in which case, cartridges can be used for 4 hr.Used cartridges should be discarded daily, regardless of the length of timeused

Aerosols, in common with most vapours/ mists, should never be used inconfined spaces without adequate ventilation. Aerosols, containing agentsdesigned to enhance or mask smell, have triggered allergic reactions inpredisposed individuals.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties

Appearance Flammable liquid with a characteristic odour; not miscible with water.Supplied as an aerosol pack. Contents under PRESSURE. Contains highly flammable hydrocarbon propellant.

Physical state Liquid Relative density (Water =1) 0.66

Odour Not Available Partition coefficientn-octanol / water Not Available

Odour threshold Not Available Auto-ignition temperature(°C) Not Available

pH (as supplied) Not Available Decompositiontemperature Not Available

Melting point / freezingpoint (°C) Not Available Viscosity (cSt) Not Available

Initial boiling point andboiling range (°C) -44.5 (initial) Molecular weight (g/mol) Not Applicable

Flash point (°C) -97 Taste Not Available

Evaporation rate Not Available Explosive properties Not Available

Flammability HIGHLY FLAMMABLE. Oxidising properties Not Available

Upper Explosive Limit (%) 10.9 Surface Tension (dyn/cmor mN/m) Not Available

Lower Explosive Limit (%) 0.6 Volatile Component (%vol) 89.5%

Vapour pressure (kPa) 210 @20C Gas group Not Available

Solubility in water Immiscible pH as a solution (1%) Not Available

Vapour density (Air = 1) Not Available VOC g/L 81.9%

SECTION 10 STABILITY AND REACTIVITY

Reactivity See section 7

Chemical stability

Elevated temperatures. Presence of open flame. Product is considered stable. Hazardous polymerisation will not occur.

Possibility of hazardousreactions See section 7

Conditions to avoid See section 7

Incompatible materials See section 7

Hazardous decompositionproducts See section 5

SECTION 11 TOXICOLOGICAL INFORMATION

Information on toxicological effects

Inhaled

Inhalation of vapours may cause drowsiness and dizziness. This may be accompanied by sleepiness, reduced alertness, loss ofreflexes, lack of co-ordination, and vertigo.Inhalation of aerosols (mists, fumes), generated by the material during the course of normal handling, may be damaging to thehealth of the individual.There is some evidence to suggest that the material can cause respiratory irritation in some persons. The body's response tosuch irritation can cause further lung damage.Inhalation of high concentrations of gas/vapour causes lung irritation with coughing and nausea, central nervous depression withheadache and dizziness, slowing of reflexes, fatigue and inco-ordination.Central nervous system (CNS) depression may include general discomfort, symptoms of giddiness, headache, dizziness,nausea, anaesthetic effects, slowed reaction time, slurred speech and may progress to unconsciousness. Serious poisoningsmay result in respiratory depression and may be fatal.

Material is highly volatile and may quickly form a concentrated atmosphere in confined or unventilated areas. The vapour maydisplace and replace air in breathing zone, acting as a simple asphyxiant. This may happen with little warning of overexposure.WARNING:Intentional misuse by concentrating/inhaling contents may be lethal.Exposure to hydrocarbons may result in irregularity of heart beat. Symptoms of moderate poisoning may include dizziness,headache, nausea.

Ingestion

Accidental ingestion of the material may be damaging to the health of the individual.Not normally a hazard due to physical form of product.Considered an unlikely route of entry in commercial/industrial environmentsCentral nervous system (CNS) depression may include general discomfort, symptoms of giddiness, headache, dizziness,nausea, anaesthetic effects, slowed reaction time, slurred speech and may progress to unconsciousness. Serious poisoningsmay result in respiratory depression and may be fatal.

Skin Contact

The liquid may be able to be mixed with fats or oils and may degrease the skin, producing a skin reaction described asnon-allergic contact dermatitis. The material is unlikely to produce an irritant dermatitis as described in EC Directives.Spray mist may produce discomfortOpen cuts, abraded or irritated skin should not be exposed to this material

Eye There is some evidence to suggest that this material can cause eye irritation and damage in some persons.Not considered to be a risk because of the extreme volatility of the gas.

Chronic

Substance accumulation, in the human body, may occur and may cause some concern following repeated or long-termoccupational exposure.Main route of exposure to the gas in the workplace is by inhalation.Chronic or repeated exposure to pentanes may cause lung inflammation, fluid in the lungs and nerve damage. It may manifestwith dizziness, weight loss, anaemia, nervousness, pain in the limbs and numbness ("pins and needles sensation").Prolonged or repeated skin contact may cause drying with cracking, irritation and possible dermatitis following.Constant or exposure over long periods to mixed hydrocarbons may produce stupor with dizziness, weakness and visualdisturbance, weight loss and anaemia, and reduced liver and kidney function. Skin exposure may result in drying and crackingand redness of the skin.

Nulon Chain LubeTOXICITY IRRITATION

Not Available Not Available

n-pentane

TOXICITY IRRITATION

Dermal (rabbit) LD50: =3000 mg/kg[2] Not Available

Inhalation (rat) LC50: 364 mg/l/4H[2]

Oral (rat) LD50: >2000 mg/kg[1]


TOXICITY IRRITATION

Dermal (rabbit) LD50: >1900 mg/kg[1] Eye: no adverse effect observed (not irritating)[1]

Inhalation (rat) LC50: 8.5 mg/l/4H[2] Skin: adverse effect observed (irritating)[1]

Oral (rat) LD50: >4500 mg/kg[1]

butaneTOXICITY IRRITATION

Inhalation (rat) LC50: 658 mg/l/4H[2] Not Available

propaneTOXICITY IRRITATION

Inhalation (rat) LC50: >49942.95 mg/l/15M[2] Not Available

Legend: 1. Value obtained from Europe ECHA Registered Substances - Acute toxicity 2.* Value obtained from manufacturer's SDS. Unless otherwise specified data extracted from RTECS - Register of Toxic Effect of chemical Substances

N-PENTANE [GENIUM and CCINFO, V.W.&R.]

Legend: – Data either not available or does not fill the criteria for classification – Data available to make classification

NAPHTHA PETROLEUM,ISOPARAFFIN,

HYDROTREATED

For petroleum: This product contains benzene, which can cause acute myeloid leukaemia, and n-hexane, which can bemetabolized to compounds which are toxic to the nervous system. This product contains toluene, and animal studies suggesthigh concentrations of toluene lead to hearing loss. This product contains ethyl benzene and naphthalene, from which animaltesting shows evidence of tumour formation.Cancer-causing potential: Animal testing shows inhaling petroleum causes tumours of the liver and kidney; these are howevernot considered to be relevant in humans.Mutation-causing potential: Most studies involving gasoline have returned negative results regarding the potential to causemutations, including all recent studies in living human subjects (such as in petrol service station attendants).

Nulon Chain Lube &NAPHTHA PETROLEUM,

ISOPARAFFIN,HYDROTREATED &

PROPANE

No significant acute toxicological data identified in literature search.

Nulon Chain Lube &NAPHTHA PETROLEUM,

ISOPARAFFIN,HYDROTREATED

Animal studies indicate that normal, branched and cyclic paraffins are absorbed from the gastrointestinal tract and that theabsorption of n-paraffins is inversely proportional to the carbon chain length, with little absorption above C30. With respect to thecarbon chain lengths likely to be present in mineral oil, n-paraffins may be absorbed to a greater extent than iso- or cyclo-paraffins.The major classes of hydrocarbons are well absorbed into the gastrointestinal tract in various species. In many cases, thehydrophobic hydrocarbons are ingested in association with fats in the diet. Some hydrocarbons may appear unchanged as in thelipoprotein particles in the gut lymph, but most hydrocarbons partly separate from fats and undergo metabolism in the gut cell.

Acute Toxicity Carcinogenicity

Skin Irritation/Corrosion Reproductivity

Serious EyeDamage/Irritation STOT - Single Exposure

Respiratory or Skinsensitisation STOT - Repeated Exposure

Mutagenicity Aspiration Hazard

SECTION 12 ECOLOGICAL INFORMATION

Toxicity

Nulon Chain LubeENDPOINT TEST DURATION (HR) SPECIES VALUE SOURCE

NotAvailable Not Available Not Available Not

AvailableNotAvailable

n-pentane

ENDPOINT TEST DURATION (HR) SPECIES VALUE SOURCE

LC50 96 Fish 3.193mg/L 3

EC50 48 Crustacea 2.7mg/L 2

EC50 72 Algae or other aquatic plants 1.26mg/L 2

NOEC 72 Algae or other aquatic plants 4.549mg/L 2



LC50 96 Fish 4.1mg/L 2

EC50 48 Crustacea 4.5mg/L 2

EC50 72 Algae or other aquatic plants >1-mg/L 2

butane


LC50 96 Fish 5.862mg/L 3


propane


LC50 96 Fish 10.307mg/L 3


Legend: Extracted from 1. IUCLID Toxicity Data 2. Europe ECHA Registered Substances - Ecotoxicological Information - Aquatic Toxicity3. EPIWIN Suite V3.12 (QSAR) - Aquatic Toxicity Data (Estimated) 4. US EPA, Ecotox database - Aquatic Toxicity Data 5.ECETOC Aquatic Hazard Assessment Data 6. NITE (Japan) - Bioconcentration Data 7. METI (Japan) - Bioconcentration Data 8.Vendor Data

Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment. Do NOT allow product to come in contact with surface waters or to intertidal areas below the mean high water mark. Do not contaminate water when cleaningequipment or disposing of equipment wash-waters.Wastes resulting from use of the product must be disposed of on site or at approved waste sites.When spilled this product may act as a typical oil, causing a film, sheen, emulsion or sludge at or beneath the surface of the body of water. The oil film on water

surface may physically affect the aquatic organisms, due to the interruption of theoxygen transfer between the air and the waterOils of any kind can cause:

drowning of water-fowl due to lack of buoyancy, loss of insulating capacity of feathers, starvation and vulnerability to predators due to lack of mobilitylethal effects on fish by coating gill surfaces, preventing respirationasphyxiation of benthic life forms when floating masses become engaged with surface debris and settle on the bottom andadverse aesthetic effects of fouled shoreline and beaches

In case of accidental releases on the soil, a fine film is formed on the soil, which prevents the plant respiration process and the soil particle saturation. It maycause deep water infestation.For Isopentane: Koc ~520; Henry's Law Constant: 1.4 atm-cu m/mole; Water Solubility: 48mg/L; Vapor pressure ~689 mm Hg.Atmospheric Fate: Isopentane is expected to exist only as vapor in the atmosphere. Vapor-phase isopentane is degraded in the atmosphere by reaction withphotochemically-produced hydroxyl radicals; the half-life for this reaction in air is estimated to be 4 days.Terrestrial Fate: Soil - Isopentane is expected to have low mobility in soil.For Butane (Synonym: n-Butane): Log Kow: 2.89; Koc: 450-900; Henry�s Law Constant: 0.95 atm-cu m/mole, Vapor Pressure: 1820 mm Hg; BCF: 1.9.Atmospheric Fate: Butane is expected to exist only as a gas in the ambient atmosphere. Gas-phase n-butane is degraded in the atmosphere by reaction withhydroxyl radicals; the half-life for this reaction in air is estimated to be 6.3 days, (@ 25 C). Butane is not expected to absorb UV light and probably will probably notbe broken down directly by sunlight in the atmosphere.Environmental Fate: n-Pentane may be released into the environment through various waste streams as a result of its production and use as a general laboratorysolvent, solvent for polymerization reactions, and as a raw material in the synthesis of olefins and other industrial chemicals.Terrestrial Fate: If released to soil, n-pentane is expected to volatilize from moist and dry soil surfaces based upon its physico-chemical properties. Screening testresults show that n-pentane may undergo biodegradation under aerobic conditions. Volatilization is primarily the dominant fate process of the compound.For Propane: Koc 460. logKow 2.36.Henry's Law constant of 7.07x10-1 atm-cu m/mole, derived from its vapour pressure, 7150 mm Hg, and water solubility, 62.4 mg/L. Estimated BCF: 13.1.DO NOT discharge into sewer or waterways.

Persistence and degradabilityIngredient Persistence: Water/Soil Persistence: Air

n-pentane LOW LOW

butane LOW LOW

propane LOW LOW

Bioaccumulative potentialIngredient Bioaccumulation

n-pentane LOW (BCF = 2.35)

butane LOW (LogKOW = 2.89)

propane LOW (LogKOW = 2.36)

Mobility in soilIngredient Mobility

n-pentane LOW (KOC = 80.77)

butane LOW (KOC = 43.79)

propane LOW (KOC = 23.74)

SECTION 13 DISPOSAL CONSIDERATIONS

Waste treatment methods

Product / Packagingdisposal

Legislation addressing waste disposal requirements may differ by country, state and/ or territory. Each user must refer to lawsoperating in their area. In some areas, certain wastes must be tracked.A Hierarchy of Controls seems to be common - the user should investigate:

Reduction Reuse Recycling Disposal (if all else fails)

This material may be recycled if unused, or if it has not been contaminated so as to make it unsuitable for its intended use.DO NOT allow wash water from cleaning or process equipment to enter drains. It may be necessary to collect all wash water for treatment before disposal. In all cases disposal to sewer may be subject to local laws and regulations and these should be considered first. Where in doubt contact the responsible authority. Consult State Land Waste Management Authority for disposal. Discharge contents of damaged aerosol cans at an approved site. Allow small quantities to evaporate. DO NOT incinerate or puncture aerosol cans.

SECTION 14 TRANSPORT INFORMATION

Labels Required

Marine Pollutant NO

HAZCHEM Not Applicable

Land transport (ADG)

UN number 1950

UN proper shipping name AEROSOLS

Transport hazard class(es)Class 2.1

Subrisk Not Applicable

Packing group Not Applicable

Environmental hazard Not Applicable

Special precautions foruser

Special provisions 63 190 277 327 344 381

Limited quantity 1000ml

Air transport (ICAO-IATA / DGR)

UN number 1950

UN proper shipping name Aerosols, flammable (engine starting fluid); Aerosols, flammable

Transport hazard class(es)

ICAO/IATA Class 2.1

ICAO / IATA Subrisk Not Applicable

ERG Code 10L




Special provisions A145 A167 A802; A1 A145 A167 A802

Cargo Only Packing Instructions 203

Cargo Only Maximum Qty / Pack 150 kg

Passenger and Cargo Packing Instructions 203; Forbidden

Passenger and Cargo Maximum Qty / Pack 75 kg; Forbidden

Passenger and Cargo Limited Quantity Packing Instructions Y203; Forbidden

Passenger and Cargo Limited Maximum Qty / Pack 30 kg G; Forbidden

Sea transport (IMDG-Code / GGVSee)

UN number 1950

UN proper shipping name AEROSOLS

Transport hazard class(es)IMDG Class 2.1

IMDG Subrisk Not Applicable




EMS Number F-D , S-U

Special provisions 63 190 277 327 344 381 959

Limited Quantities 1000 ml

Transport in bulk according to Annex II of MARPOL and the IBC codeNot Applicable

SECTION 15 REGULATORY INFORMATION

Safety, health and environmental regulations / legislation specific for the substance or mixture

N-PENTANE IS FOUND ON THE FOLLOWING REGULATORY LISTS

Australia Hazardous Chemical Information System (HCIS) - HazardousChemicalsAustralia Inventory of Chemical Substances (AICS)

Australia Standard for the Uniform Scheduling of Medicines and Poisons(SUSMP) - Schedule 4Australia Standard for the Uniform Scheduling of Medicines and Poisons(SUSMP) - Schedule 5

NAPHTHA PETROLEUM, ISOPARAFFIN, HYDROTREATED IS FOUND ON THE FOLLOWING REGULATORY LISTS

Australia Hazardous Chemical Information System (HCIS) - HazardousChemicalsAustralia Inventory of Chemical Substances (AICS)Australia Standard for the Uniform Scheduling of Medicines and Poisons(SUSMP) - Schedule 5

Chemical Footprint Project - Chemicals of High Concern ListInternational Agency for Research on Cancer (IARC) - Agents Classified bythe IARC Monographs

BUTANE IS FOUND ON THE FOLLOWING REGULATORY LISTS


Australia Standard for the Uniform Scheduling of Medicines and Poisons(SUSMP) - Schedule 5Chemical Footprint Project - Chemicals of High Concern List

PROPANE IS FOUND ON THE FOLLOWING REGULATORY LISTS


Australia Standard for the Uniform Scheduling of Medicines and Poisons(SUSMP) - Schedule 5

National Inventory StatusNational Inventory Status

Australia - AICS Yes

Canada - DSL Yes

Canada - NDSL No (n-pentane; naphtha petroleum, isoparaffin, hydrotreated; butane; propane)

China - IECSC Yes

Europe - EINEC / ELINCS /NLP Yes

Japan - ENCS No (naphtha petroleum, isoparaffin, hydrotreated)

Korea - KECI Yes

New Zealand - NZIoC Yes

Philippines - PICCS Yes

USA - TSCA Yes

Taiwan - TCSI Yes

Mexico - INSQ Yes

Vietnam - NCI Yes

Russia - ARIPS Yes

Legend:Yes = All CAS declared ingredients are on the inventoryNo = One or more of the CAS listed ingredients are not on the inventory and are not exempt from listing(see specific ingredientsin brackets)

SECTION 16 OTHER INFORMATION

Revision Date 01/11/2019

Initial Date 20/10/2017

SDS Version SummaryVersion Issue Date Sections Updated

3.1.1.1 01/11/2019 One-off system update. NOTE: This may or may not change the GHS classification

Other informationClassification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the ChemwatchClassification committee using available literature references.

The SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risksin the workplace or other settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and current or availableengineering controls must be considered.

Definitions and abbreviationsPC－TWA: Permissible Concentration-Time Weighted AveragePC－STEL: Permissible Concentration-Short Term Exposure LimitIARC: International Agency for Research on Cancer

ACGIH: American Conference of Governmental Industrial HygienistsSTEL: Short Term Exposure LimitTEEL: Temporary Emergency Exposure Limit。IDLH: Immediately Dangerous to Life or Health ConcentrationsOSF: Odour Safety FactorNOAEL :No Observed Adverse Effect LevelLOAEL: Lowest Observed Adverse Effect LevelTLV: Threshold Limit ValueLOD: Limit Of DetectionOTV: Odour Threshold ValueBCF: BioConcentration FactorsBEI: Biological Exposure Index

This document is copyright.Apart from any fair dealing for the purposes of private study, research, review or criticism, as permitted under the Copyright Act, no part may be reproduced by anyprocess without written permission from CHEMWATCH.TEL (+61 3) 9572 4700.

Documents

Nulon Chain Lube · Nulon Products Australia Chemwatch Hazard Alert Code: 4 Nulon Chain Lube Chemwatch: 86-2660 ... Removal of contact lenses after an eye injury should only be undertaken