nuvo COOLING UNIT UPGRADE

b y ko olspaceTM

INSTALLATION & OPERATION

BEFORE YOU START

SCREW INSERTS x 2

ALLEN KEY x 1

HARDWARE

MAKE SURE TO WRITE DOWN YOUR SERIAL

NUMBER AND SAVE IT !!!

32 mm1.25"

423 mm16.625"

Ø 9 x 25.4OR 11/32" x 1" DEEP

NEW SETUP

PREPARE FOR INSTALLATION

CUT OUT PATTERN ON BACK PAGE AND ALIGN WITH EDGE OF COOL-ING UNIT HOLE TO MARK FOR DRILL-ING

1

1

1

USE 9mm OR 11/32” DRILL BIT, DRILL HOLE 1” DEEP

2

2

INSERT SCREW INSERT3

3

4b

4b

BACKOFCELLAR

BACK OF CELLAR

BACK

MAKE SURE DISTANCE BETWEEN THE HOLES IS CORRECT BEFORE

DRILLING!!!

CELLARS WITHOUT INSULATION STRIPSUSE 3/4” FOAM TAPE 1/8” THICK ON ALL 4 SIDES OF INSIDE FLANGE

4a

YOUR ORIGINAL SETUP

4b

BACK

FOR TUSCANY PLUS CELLARSREMOVE ALL 4 INSULATION STRIPS AND FLIP TO RE-INSERT AS NEW SET UP

2 Flange bolts in cooling unit box.

COOLING UNIT INSTALLATION

1

A

B

TOP VIEW

Run light cord through Cut-out. Slide unit into the back opening by angling unit A to allow light cord to clear and straighten to push in B . Screw allen bolts through bottom flange holes. Make sure unit is level!

NOTE: If unit is operated according to specifications overflows will not occur. Excess condensation is only caused by extreme conditions. Unit will shut off at 72 °F and will restart when temperature drops or unit is plugged in. (In this case insert 3/8” O.D. hose to drain hole, cut to appropriate length.)

Container

Optional (not required) except as emergency drain.

BACKOFCELLAR

TOP VIEW

FEATURES: - Default SET temperature 57º F/14º C (ideal for wine storage). - Calibration option of the temperature sensor. - Display of actual temperature by request. - SET temperature range 52ºF-64ºF. - Digital temperature sensor. - Dual display Fº/Cº. - Settings are stored in memory for power failures. - Pre programed software will reach the quietest most efficient operation.

OPERATION: - The display will show the detected temperature until the temperature will fall within 3º of the SET POINT. - If the temperature is above the default 57º F + 1º or other preset value, after a delay of 1 minute the fan will start, followed by the compressor within the next minute. - The unit will cycle ON/OFF based on the temperature reading. Fan speeds are automatically set by the controller to achieve optimum performance. - Minimum ON and OFF cycle times are imposed by software, to prevent "short cycling".

SAFETY FEATURES:

ALARM: - If the temperature exceeds 72º F the unit will shut down, a sound warning will start and the dispaly will blink alternating with the temperature reading. - This function is disabled in the first 4 hours “ Cool Down” period or after any reset for another 4 hours. - The unit will restart and continue the cooling and cycling if the temperature falls below 72º F.

TO RESET: - Unplug and re plug the unit.

57º 56º

70º 57º

57º 57º

57º 58º

57º 56º

57º 14º

57º 57º

57º F0

F0 F1

F0 -1

Actual temperature: PRESS

SET temperature: PRESS

PRESS and RELEASE

To increase: PRESS once per degree

To decrease: PRESS once per degree

The new value will be memorized and the controller will reset automatically.

PRESS and HOLD until buzzer sounds in 5 seconds

The new value will be memorized and the controller will reset automatically.

PRESS and HOLD while holding PRESS and RELEASEWait 5 secondsUSE or for each degree of offset

DISPLAY EXAMPLE

BEFORE AFTER

TO DISPLAY:

TO MODIFY SET TEMPERATURE(range is 52-64ºF):

TO CHANGE FROM ºF to ºC: or ºC to ºF TO CALIBRATE:

CONTROLLER OPERATION ACTION

NOTE: A negative offset will result in a warmer cabinet and a positive offset will result in a cooler cabinet. The new value will be memorized and the controller will reset automatically.

CONTROLS : PLUG IT IN (wait one minute) and ENJOY!

57

KEYS

AL

DISPLAY:

PLEASE CUT OUT TEMPLATE PATTERN FOR DRILL HOLE PLACEMENT