OOOOpppperationerationerationeration ManualManualManualManualSMSSMSSMSSMS AirAirAirAir ConditionerConditionerConditionerConditioner RemoteRemoteRemoteRemote ControlControlControlControllerlerlerler

ModelModelModelModel No.:No.:No.:No.: SR-001SR-001SR-001SR-001

Please read these instructions before operating your product and retain them for future reference.The images shown in this manual are for illustrative purpose only.

Thank you for purchasing our product.

This smart unit is not only a remote controller of your air conditioner/heat pump, but also aremote monitor of your room temperature. All operations are based on GSM network SMS(Short Message Service) platform, thus you can do remote control/monitoring anywhereand anytime.

It also provides a prompt, economic pre-warning method on high/low temperature andpower dump. While your room temperature is too high/low, or the power supply isoff/resumed, it will automatically send you an alarm message.

Please take a while to read this manual, then follow the instructions to finish your settings.After that, just relax and enjoy it!

HardwareHardwareHardwareHardware introductionintroductionintroductionintroduction

Front view

Back view

How to use the keypad

: Return key, to cancel an operation or delete a number;: Equals to “OK” key;: Factory reserved, equals to “call up” key.: Power on /off

InstallationInstallationInstallationInstallation

Insert a SIM card (GSM card only, typically 3.0V), install the Lithium-ion battery, thenpress the power key (hold the key above 3 seconds) to initialize the system. Keepwaiting several seconds until it access your local GSM network, the start-up softwareinterface displays as below:

Press “OK” or key to enter main menu, then choose “Settings”, it will display 3submenues: User List，Temp. Alarm，and Power Alarm.

Set up an user list. It is a necessary step to start up all built-in functions. Manuallyinput 1~3 mobile phone no.(s) including the area code. ( DO NOT input the SIM card No.of the system itself), only the registered phone no.(s) can access the system and get thepre-warning messages.

Don’t forget the phone no. prefix!

CountryCountryCountryCountry Area CodeArea CodeArea CodeArea Code Phone No. PrefixPhone No. PrefixPhone No. PrefixPhone No. Prefix

Denm arkDenm arkDenm arkDenm ark 45454545 45 or 004545 or 004545 or 004545 or 0045

Sw edenSw edenSw edenSw eden 46464646 46 or 004646 or 004646 or 004646 or 0046

Norw ayNorw ayNorw ayNorw ay 47474747 47 or 004747 or 004747 or 004747 or 0047

Ice landIcelandIcelandIceland 354354354354 354 or 00354354 or 00354354 or 00354354 or 00354

FinlandFinlandFinlandFinland 358358358358 358 or 00358358 or 00358358 or 00358358 or 00358

ChinaChinaChinaChina 86868686 86 or 008686 or 008686 or 008686 or 0086

Enable the firewall. We strongly recommend you to select this key. If you choose “Disable”,system will lose its security protection features, that means everybody can control your airconditioner by sending SMS command via mobile phone)

Enter “Temp. Alarm” submenu, set the temperature for “Freeze Alarm” and “Heat Alarm”.The temperature value will be a trigger for pre-warning, once your room temperaturereaches your set point, you will get an alarm message.

Settings--Temp. Alarm-- Freeze alarm, set a temperature between 1~10 degree C (suchas 9.2 degree C) , then Enable the Freeze Alarm ( This means once your roomtemperature drops to 9.2 degree C, you will get an alarm message)

Enter “Temp. Setting” submenu， the default temperature value for “Freeze Alarm” is 8degree C，Press “Edit” key to input a new value，The temperature span is within 1℃~10℃.

Settings-- Temp. Alarm--Heat alarm, set a temperature between 26~46 degree C (such as31.5 degree C),then Enable the Heat Alarm ( This means once your roomtemperature reaches 31.5 degree C, you will get an alarm message)

Enter “Temp. Setting” submenu. the default temperature value for “Heat Alarm” is 32degree C， Press “Edit” key to input a new value， The temperature span is within26℃~46℃，

Enable Power alarmSettings--Power alarm, select the "Enable" button, (This means once the city power isoff/resumed, you will get an alarm message ).

This unit works by intelligently learn the infrared signals from a certain remote controller ofair conditioner.

Enter “IR Codes” submenu, input the IR (Infrared) codes. This is a necessary step toremotelly control your Air Conditioner.

IR codes-- Code learning, one by one input 1~6 IR codes to the system, (For simpleoperation, just input 2 or 4 “common” codes is OK); Once you see a note "Point yourremote controller at me, then press a proper button", Immediately use yourhandheld remote controller to "Shoot" the unit, it will automatically capture the IR codeand store it into the memory.The operation need to be finished within 3 seconds, otherwise you will get a “Fail”feedback.

Reception of IR codes can be checked by pressing “TEST” key after “Code Learning” isfinished. If an infrared reception sound (such as beep) from the air conditioner can be

heard, it indicates the IR codes has been successfully received.

IR codes-- Code test, one by one test the IR codes you have input to the system.

CommandCommandCommandCommand ListListListListUsers can compose short message command to do remote control/monotoring.

““““StatusStatusStatusStatus”””” command : System will check its surrounding environment and feedback thereal time room temperature, GSM signal strength, power supply status;““““*01**01**01**01*”””” command : System will transmit Code 1 to Air conditioner, then feedback a “ SetOK” message;““““*02**02**02**02*”””” command : System will transmit Code 2 to Air conditioner, then feedback a “ SetOK” message;…““““*06**06**06**06*”””” command : System will transmit Code 6 to Air conditioner, then feedback a “ SetOK” message;

Specifications:Specifications:Specifications:Specifications:

GSM 900 / DCS1800MHz dual frequencyInfrared signal transmitting distance: ≦10mPower supply: DC 5.0V power adapterLithium-ion battery: 3.7V 1000mAhRecharge limited voltage: 4.2VIn door use only.