Upload
others
View
11
Download
2
Embed Size (px)
Citation preview
MODEL:< ◇ > PRELIMINARY SPECIFICATION
< ◆ > APPROVAL SPECIFICATION
CUSTOMER
APPROVED BY
DATE:
DESIGNED CHECKED APPROVED
深圳市恒通视讯科技有限公司Shenzhen Heng Tong Video Technology Co. Ltd.
HT043DA-V.0
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
地址:深圳市宝安区西乡臣田工业区宝民二路东方大厦 7楼
TEL:0755-2302 3597 FAX:0755-29064706
Http://www.tft-lcd360.com E-mail:[email protected]
2018-04-7
- 1 -
REVISION RECORD
REV NO REV DATE PAGE CONTENTS ISSUER
1.0 2016-12-1 18 First release Liqin
1.1 Modify Timing characteristics Liqin
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 2 -
TABLE OF CONTENT
GENERAL SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
DIMENSIONAL DRAWING
INTERFACE PIN CONNECTIONS
TIMING CHARACTERISTICS OF INPUTSIGNAL
ELECTRO-OPTICAL CHARACTERISTICS
RELIABILITY
INSPECTION CRITERIA
PACKING DRAWING
HANDLING PRECAUTION
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
HT043DA-V.0-TFT1N18
- 3 -
1.0 GENERAL SPECIFICATIONS
is a color active matrix LCD module incorporatingamorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCDpanel, driver IC, FPC and a back light unit. The module display area contains 480x272 pixels. This product accords with RoHS environmental criterion.
Item Contents Unit
Viewing direction 6:00 O' Clock
Number of Pixels 480(RGB) x272 /
TFT-LCD manufacturers BOE
Number of color 16.7M /
Shape size 105.5*67.15*2.9 mm
Active area (WxH) 95.04mm(W)×53.856mm(H) mm
Pixel Pitch 0.198mm(H)×0.198mm(W) mm
Backlight Type 7*1chips white LED /
Backlight life 50000 hours
Interface RGB
LCM Luminance 220(typ) cd/m2
Contrast Ratio 200(typ)
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 4 -
2.0 ABSOLUTE MAXIMUM RATINGSThe following are maximum values which, if exceeded ,may cause fauity operation or damage to the unit.
ITEM SYMBOL MIN TYP MAX UNIT NOTEDigital Power Supply Voltage VDD -0.3 - 4.4 V -
Analog Power Supply Voltage VDDI -0.3 - 4 V -
TFT Gate on voltage VGH 11.5 15 19 V -
TFT Gate off voltage VGL -16 -10 -8.5 V -
Common Power Supply Voltage VCOM -3.475 -0.68 -3 V -
TFT Gate on voltage VGH 10.5 15 18 V
TFT Gate off voltage VGL -15.5 -10 -7 V
Common Power Supply Voltage VCOM -4 -0.68 -0.2 V
Note :If users use the product out off the environment operation range (temperature and humidity ,it will have visual quality
concerns
3.0 ELECTRICAL CHARACTERISTICSRecommended Operating Condition
Item Symbol Min TYP Max Unit NOTE
Supply voltage for logic VDD 3.1 3.3 3.5 V
Note1:Please adjust VCOM to make the flicker level be minimum.
3.1 BACKLIGHT CHARACTERISTICS
Item Symbol Min Typ Max Unit ConditionForward voltage Vf 18.9 22.4 23.8 V If=20mA
Luminance Lv 200 220 - cd/m2 If=20mA
Number of LED -- 7 Piece --
Connection mode P 7serial 1parallel -- --
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 5 -
4.0 DIMENSIONAL DRAWING
H
32
15
4
SCALE
DATE
1:1
COLOR
mmUN
ITmm
76
GF
PART N
o.
DESCRI
PTIO
N
MATERI
AL
D EC
3
BA
12
45
67
H
8
DRAW
N BY
CHEC
KED
BY
G
APPR
OVED
BY
FD ECBA±
0.15
±0.
05
±0.
10
L>18
.0
6.0<
L<=1
8.0
FIELD
L<=6
.00
TOLERA
NCES
Angl
e
8
1°
A0
版 来 源 于 试 做 图 T0
版
正 式 图
模组
图内
容变
更原
因修
订人
日期
修改
绘 图
审 核
料 号
单
位颜
色
材 质
2016
-12
-1
REV
A0
版 本
核 准
描 述
比 例
日 期
REM
ARK
UNI
TMAX
TYP
MIN
SYM
BOL
PAR
AME
TERELE
CTR
ICA
L/O
PRICA
L C
HAR
ACT
ERI
STI
CS
AT
Ta=25
℃
19.
623.
822.
4
0.4
50
0.4
00
0.3
50
0.3
60
0.3
10
0.2
60
220
200
IF=
20m
A
IF=
20m
A
IF=2
0mA(中
心点
)
80
YXcoo
rdi
nai
es
Lighting area B
B/3 B/6B/3B/6
A/6
A/3
A/3
A/6
93 65 8
74
21
Light
ing Ar
ea A
5100476
50
75
※1.In
tern
al Circ
uit Dia
gram
C°
※1
※1
mA V
Rev
ers
eVo
lta
ge
ABS
OLU
TE
MAX
IMUM
RAT
ING
S A
T T
a=2
5℃
※7
mW
TTOPR
VRIFP
Pd
REM
ARK
UNI
TS
SPE
CIF
ICA
TIO
NSYM
BOL
Sto
rag
e T
emp
eratu
re
Ope
rar
ing
Te
mpera
tur
e
Pea
k F
orw
ard
Curr
ent
Pow
er
Dis
sip
ation
PAR
AME
TER
(mi
n/m
ax)*10
0
VR=10
V,※
1
F R
%uAV
cd/
m2
Iv-
m
IVIv
Lum
ino
us
Tol
eranc
e
Rev
ers
e C
urr
ent
For
war
d V
olt
age
Cen
ter
Lum
ino
usInt
ens
ity
C°C°
C°C°
-10
TO+
60
0
TO+
60
测试
仪器
:K-8
LED_
KLE
D_A (LED 7×
1=
7 SMDS)
CURRENT IF=20*1=20mA
DESCRIPTION
PIN
27
28
30
29
25
2624
19 23
22
21
20
3 11
15 16
18
17
12
13
147 8 9 104 651 2
B7B6
B5
B3G6
G1 G3
G2
G0R7
R5
R4
R1
B2
B0 B1
GNDB4
G7R6
R0
CLKLED
A
LED
K
VDDGND
R3
R2
G5G4
37
38
40
39
35
3634
33
32
31
YD(
NC)
RX(
NC)
GND
DEN
VSY
NC
DIS
P
HSY
NC
XL(
NC)
NC
YU(
NC)
AK
AK
P0.1
2*(4
0-1)
=19.5
0±0.0
5
0.50
W=0.
30
P=0.
50
3.5
140
DETAI
L"A"(
4:1)
140
KA
YU
XL
YD
YR
易撕
贴
105.50±
0.2(Out Line)
67.15±0.2(Out Line)
95.04 AA
53.86 AA
(52.70)
(30.97)
5.18
3.30
4.04
2.83
18.70
45.51
(56.70)
(98.80)
PI补
强
单层
区
40
1
2.90±
0.2
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
深圳
市恒
通视
讯科
技有
限公
司
- 6 -
5.0 INTERFACE PIN CONNECTIONS
Pin.No Symbol Function
1 VLEDK Power for LED backlight (Cathode)
2 VLEDA Power for LED backlight (Anode)
3 GND Power ground
4 VDD Common Voltage(3.3V)
5-12 R0-R7 7 Bit RED Data Bus
13-20 G0-G7 7 Bit GREEN Data Bus
21-28 B0~B7 7 Bit BLUE Data Bus
29 GND Power ground
30 CLK Colock signal
31 DISP Display on/off
32 HSYNC Horizontal sync input in RGB mode
33 VSYNC Vertical sync input in RGB mode
34 DEN Data enable
35 NC No Connection
36 GND Power ground
37-40 NC No Connection
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 7 -
6.0 Timing characteristics6.1 Parallel 24--bit RGB Timing Table
6.2 SYNC Mode Timing Diagram
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 8 -
6. 3 SYNC-DE Mode Timing Diagram
6.4 DE Mode Timing Diagram
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 9 -
7.0 ELECTRO-OPTICAL CHARACTERISTICS
ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT NOTE
Panel Transmittance T θ= 0° 12.5 15.3 -- %
Luminance L θ= 0° 200 220 -- cd/㎡Note1
Note5
Luminance Uniformity YU 9 points 75 80 -- %Note1
Note5
* Contrast Ratio CR Point-9 -- 200 -- - Note3
Response Time Rr+Tf Point-5 -- 25 35 ms Note4
Viewing
Angle
K=Contrast
Ratio>10
HorizontalΘL
Point-5
θ= 0°
-- 45
Note2ΘR -- 45 --
VerticalΘU -- 20 --
ΘD -- 45 --
Color Filter
Chromacicity
WhiteX
θ= 0°0.260 0.310 0.360
Note1
Y 0.350 0.400 0.450
RedX
θ= 0°TBD TBD TBD
Y TBD TBD TBD
GreenX
θ= 0°TBD TBD TBD
Y TBD TBD TBD
BlueX
θ= 0°TBD TBD TBD
Y TBD TBD TBD
Color gamut(NTSC ratio) θ= 0° -- TBD -- %
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 10 -
The specification of the Parallel 24-bit RGB Timing Table timing parameter is shown in Table
Note 1.The Definition of Vth & Vsat
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 11 -
Note 2.Measurement Set Up
Note 3. Response Time Testing
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 12 -
8.RELIABILITY
8.1 MTBFThe LCD module shall be designed to meet a minimum MTBF value of 50000 hours with normal.
(25°C in the room without sunlight)
8.2 TESTSNO. Test Item Test condition Criterion
1 High Temperature Storage 60℃±2℃ 96HRestore 2H at 25℃Power off
2 Low Temperature Storage -10℃±2℃ 96HRestore 2H at 25℃Power off
3 High Temperature Operation 60℃±2℃ 96HRestore 2H at 25℃Power on
4 Low Temperature Operation 0℃±2℃ 96HRestore 2H at 25℃Power on
5 High Temperature & Humidity Operation 50℃±2℃ 90%RH 96HPower on
6 Temperature Cycle -20℃←→25℃←→70℃30min 5min 30min
after 10cycle, Restore 2H at 25℃
Power off
Aftertesting,cosmeticand electrical defectsshould not happen.
7 Vibration Test 10Hz~150Hz, 100m/s2, 120min
8 Shock Test Half-sinewave,300m/s2,11ms
9 Drop Test(package state) 800mm, concrete floor,1corner,3edges, 6 sides each time
1.After testing,cosmetic and electricaldefects should nothappen.2.the product shouldremain at initial place3.Product uncoveredor package broken isnot permitted.
10 Electro Static Discharge Test(non-operation)
150pF,330Ω,Contact:±4KV,Air:±8KVMeasure point :LCD glass andmetal bezel
IEC61000-4-2:2001GB/T17626.2-2006
200pF,0Ω,±200V contact testMeasure point :IF connector pins
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 13 -
9.0 Inspection Standards9.0 INSPECTION STANDARDS9.1 Purpose
This incoming inspection standard shall be applied to TFT-LCD supplied by ZHONGSHEN to its customer.
9.2 ScopeThis inspection standard contains Cosmetic Specifications and Electrical Specifications.
9.3 Classification of defects9.3.1 Major defect.
The major defect is a defect that is likely to result in product failure or reduction in
Product’s intended usage.
9.3.2 Minor defect.
The minor defect is a defect that has little bearing on the effective use or Operation of the product.
9.4 Definition9.4.1 Display area definition
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 14 - 480RGB272dots-matrix
9.5 Inspection conditions is as follows9.5.1 Viewing distance is approximately 35-40 cm
9.5.2 Viewing angle is normal to the LCD panel as 45°
9.5.3 Ambient temperature is approximately 25±5℃
9.5.4 Ambient humidity is 60±5% RH
9.5.5 Ambient luminance is from 300-500 Lux.
9.5.6 Input signal timing should be typical value(3s-5s).
9.5.7 Mura & Light leakage inspection at ND-Filter 6%.
45°45°
LCM
35~40cm
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 15 -
9.6 Sampling method9.6.1 According to the MIL-STD-105E general inspection level , Ⅱ Sampling plan.
9.6.2 AQL: MA 0.65 MI 1.0
9.7 Inspection Criteria
DEFECT TYPE LIMIT Defect Note
VISUAL
DEFECT
SCRATCH
W≤0.05mm and L≤5mm Ignore
Maj NOTE1
0.05mm<W≤0.2mm L≤10mm N≤4
10mm<L,0.1mm<W N=0
INTERNAL
SPOT
Ф≤0.2mm Ignore
0.2mm<Ф≤0.5mm N≤4
Ф>0.5mm N=0
FIBER0.1mm≤W≤0.2mm L≤2.5mm N≤4
0.2mm<W,2.5mm<L N=0
POLARIZER BUBBLE
Ф≤0.25mm Ignore
0.25mm<Ф≤0.5mm N≤4
Ф>0.5mm N=0
DENT
Ф<0.25mm Ignore
0.25mm≤Ф≤0.5mm N≤4
Ф>0.5mm N=0
ELECTRICAL
DEFECT
BRIGHT DOT
C Area O Area Total
MajNOTE2
NOTE3
N≤4(contain C area and O
area)N≤4
DARK DOT N≤5(contain C area and O
area)N≤5
TWO ADJACENT DOTN≤1 N≤2 N≤3
THREE OR MORE ADJACENT DOTNOT ALLOWLED
LINE DEFECTNOT ALLOWLED
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 16 -
Note1: Minimum distance between dot defects and spot is 5mm;
Note2:The definition of Bright dot and Dark dot
-bright area is more than 50% of one dot
-dark area is more than 50% of one dot
-The bright dot shall be visible under ND-Filter 5% as following:
NOTE3:
-A bit rate(bright dot model )≤10%;
-Class Chipping but not affect the function of quality OK;
-Polarizing film appearance does not affect the function OK;
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 17 -
10.0 PACKINGDRAWING
1pcs foam separated
2pcs LCM to be faced
1PC/PE bagt
Packing pictures:
客户:
REVISER修订人
√临
时
规
格
正
式
规
格页 码
日 期
版 本 产品料号A1
中深:ZS043BS4001A7D1-BTT
MODEL NO
2016.10.14
5/6
REVSION
DATE
PAGE
核 准 审 核 绘 图
审核 会签
工艺部 品质部 标准化检查孙胜兴
Third LCM and second LCMback to back
3 pcsseperation/
180pcs/Carton
In the box on 1pcs foam board
sticker shipping mark
use tape to stick
shipping markSealing tape
A K
140
KA
YU
XL
YD
YR
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited
- 18 -
11.0 HANDLING PRECAUTION
(1) Don’t disassemble and reassemble the module by self.
(2) Acid, alkali, alcohol or touched directly by hand will damage the display.
(3) Static electricity will damage the module. Please configure groundingdevice.
(4)The strong vibration, shock, twist or bend will cause material damage, evenmodule broken.
(5) It is easy to cause image sticking while displaying the same pattern for verylong time.
(6) The response time, brightness and performance will vary from differenttemperature.
版权属于恒通所有,禁止任何未经授权的使用The copyright belongs to Heng Tong.Any unauthorized use is prohibited