Office of the Chairperson Purchase Committee 1 of 19 062 ... · Office of the Chairperson Purchase Committee Page 4 of 19 062-2284809 SPECIFICATIONS I.T Items Price with all Sr.#

Office of the Chairperson Purchase Committee Page 1 of 19 062-2284809


TENDER DOCUMENT FOR THE PURCHASE OF I.T ITEMS &

SCIENCE ITEMS FOR THE FINANCIAL YEAR 2017-18

THE GOVT. SADIQ COLLEGE WOMEN UNIVERSITY,

BAHAWALPUR

Note: Please read carefully these Tender document and sign & stamp each page.


PART-I (I.T Items)


SPECIFICATIONS

I.T Items Price with all

taxes Sr.# Items Description Qty.

CORE SWITCH

1

1

40 PORTS SFP/SFP+1/10Gig SWITCH (CISCO, Juniper, HP, Ruckus or

EQUALIVENT)

General Specification

1. Switch must support 40x 1/10 Giga SFP/SFP+ ports

2. Out of Band Management Ethernet Port 10/100/1000Mbps RJ45, Console Port

RJ45, File Transfer USB Port.

3. Switch should support 960Gbps Switching Capacity or Higher.

4. Forwarding Capacity 720 Mpps or Higher.

5. Switch must have the processor of Quad-core 2.4 GHz minimum.

6. Switch must have uplink slot to accommodate 2*40Gig ports or 8*10Gig ports

for future prospect

7. Switch must support the following specification minimum

a. 16 GB DDR4 DRAM

b. 16 GB FLASH

c. 32 MB shared Buffer per application Specific integrated circuit

8. Switch support 64K MAC address entries. Also support the 4K VLAN,

PVLAN. Maximum Routes = 64 K on IPv4

9. Maximum Routes = 32K on IPv6

10. The switch should support MACSEC-256 encryption algorithm.

11. The switch should support AES-256

12. Switch must have hot-swappable redundant power supply and hot-swappable

redundant fan.

13. Installation, Configuration, Commissioning and Testing

L2 & L3 Features

14. Switch must support following layer 2 features:

a. Port Mirroring

b. Spanning tree

c. 802.3ad,802.1w,802.1x-rev,802.1Q

d. VLAN Stack Q-in-Q

e. IEEE 802.1s

f. RFC 2236, RFC 3376

g. RFC 4541

h. Link fault signaling

i. PIM-SM

15. Switch must support Basic Layer 3 Protocols i.e. RIP, Static Routing.

16. Switch also must support the advance layer 3 Protocol i.e. OSPF, PBR, PIM-

SM, PIM-SSM, Virtual Route Redundancy Protocol (VRRP). If advance layer

3 options required license, then specify.

17. ISSU (In Service Software Update) must support in normal mode and open

flow as well.

18. Switch should support Open Flow 1.3 and Software Define Access

19. Maximum VRF support upto 256

QoS Features

20. QOS ACL Mapping and Marking of ToS/DSCP (CoS), ACL Mapping and

Marking of 802.1p, ACL Mapping to Priority Queue, Classifying and Limiting

Flows Based on TCP Flags, Honoring DSCP and 802.1p (CoS), Priority Flow

Control (per device).

Network Security Features

21. Switch should support the following security standards:

a. MAC authentication

b. Web authentication

c. IEEE 802.1X username export in sFlow


d. EAP Support

e. RFC 5176

f. Protection against Denial of Service (DoS) attacks

g. SSH (v1, v2)

h. Advanced Encryption Standard (AES) with SSHv2

i. RADIUS/TACACS/TACACS+

Support and Maintenance

22. 1 year Support (Hardware/Software) with Hardware Replacement Next Business Day.

LAN Switches 48 Port

2

2

General Specification 1. The switch should be L2 and have at least the following interfaces;

a. 48 x 1 Gigabit Ethernet 10/100/1000 port

b. 2 x 10 Gigabit Ethernet SFP uplink Ports

2. The switch should have at least 512 MB RAM

3. The switch should have at least 128 GB Flash memory

4. The switch should have 100 Gbps forwarding bandwidth and 95 Mpps packet

forwarding throughput

5. The switch should be 1 RU form-factor

6. The Switch should be SDN ready

7. Switch must have RPS Port to get Power from RPS Source in case of Primary

Power supply failure

8. The switch should support AC power supply


L2 Ethernet Features

10. The switch shall support VLAN IDs: 1023

11. IEEE 802.1S Multiple Spanning Tree Protocol

12. IEEE 802.1D Spanning Tree Protocol

13. DHCP Snopping & DAI

14. IEEE 802.1Q VLAN

15. IEEE 802.1w Rapid Spanning Tree Protocol

16. IEEE 802.1X Port Based Network Access Control

17. IEEE 802.1ab (Link Layer Discovery Protocol)

18. IEEE 802.3ad (Link aggregation Protocol)

19. Auto Negotiation, MDI-X Supported Interfaces

20. Switched Port Analyzer / Port Mirroring, with bidirectional data support

Network Security Features 21. AAA, Radius and Tacacs+

22. Broadcast/Multicast/Unicast Storm Control

23. Access Control Lists (Port-based ACL, VLAN-based ACL)

24. Port Security/MAC Binding

25. Secure Shell (SSH) Protocol and Simple Network Management Protocol

Version 3 (SNMPv3)

26. BPDU protect, Root protect

27. IPv6 First Hop Security

28. Private vlan

QoS Features

29. 802.1p class of service (CoS) and Differentiated Services Code Point (DSCP)

classification

30. Diffserv as per RFC 2474 or equivalent feature

Management Features

31. SNMP v1, v2c, and v3

32. Network Timing Protocol (NTP)

33. Support FTP/TFTP for upgrading the operating system

34. Support standard MIBs

Cables UK based Power Cable, console Cable



35. 1-year Hardware/Software Support with Hardware replacement in Next

Business Day.

Departmental Switches 24 Port POE

10

3

General Specification

36. The switch should be L2 and have at least the following interfaces;

a. 24 x 1 Gigabit Ethernet 10/100/1000 port

b. 2 x 10 Gigabit Ethernet SFP uplink Ports

37. The switch should have at least 512 MB RAM

38. The switch should have at least 128 GB Flash memory

39. Available POE budget should 370W or Higher

40. The switch should have 100 Gbps forwarding bandwidth and 95 Mpps packet

forwarding throughput

41. The switch should be 1 RU form-factor

42. The Switch should be SDN ready

43. Switch must have RPS Port to get Power from RPS Source incase or Primary

Power supply failure

44. The switch should support AC power supply


L2 Ethernet Features 46. The switch shall support VLAN IDs: 1023

47. IEEE 802.1S Multiple Spanning Tree Protocol

48. IEEE 802.1D Spanning Tree Protocol

49. IEEE 802.1Q VLAN

50. DHCP Snopping & DAI

51. IEEE 802.1w Rapid Spanning Tree Protocol

52. IEEE 802.1X Port Based Network Access Control

53. IEEE 802.1ab (Link Layer Discovery Protocol)

54. IEEE 802.3ad (Link aggregation Protocol)

55. Auto Negotiation, MDI-X Supported Interfaces

56. Switched Port Analyzer / Port Mirroring, with bidirectional data support

Network Security Features

57. AAA, Radius and Tacacs+

58. Broadcast/Multicast/Unicast Storm Control

59. Access Control Lists (Port-based ACL, VLAN-based ACL)

60. Port Security/MAC Binding

61. Secure Shell (SSH) Protocol and Simple Network Management Protocol

Version 3 (SNMPv3)

62. BPDU protect, Root protect

63. IPv6 First Hop Security

64. Private vlan

QoS Features

65. 802.1p class of service (CoS) and Differentiated Services Code Point (DSCP)

classification

66. Diffserv as per RFC 2474 or equivalent feature

Management Features 67. SNMP v1, v2c, and v3

68. Network Timing Protocol (NTP)

69. Support FTP/TFTP for upgrading the operating system

70. Support standard MIBs

Cables UK based Power Cable, console Cable


71. 1-year Hardware/Software Support with Hardware replacement in Next

Business day.

Training and Certification 72. Training and Certification (Routing and Switching) for 2 Personnel of GSCWU BWP.


10G SFP+

4

10 GbE SFP+ Module (Cisco, Juniper, Brocade Or Equivalent)

1. 10GBASE-LR, SFP+ optic with LC connector, 10 Km Single mode Fiber.

(DOM Support) 24

2. 1000BASE-T RJ45 8

3. 10GBASE-SR SFP+ Optic with LC Connector 2

FIREWALL

1

5

CISCO/Fortinet/Sophos or Equivalent 1. GE RJ45 Interfaces: 8

2. GE SFP Interfaces: 8

3. 10G SFP Interfaces: 2

4. Console Port : 1

5. Management ports: 2

6. Form factor: 1U or higher

7. Should include 2*10G Multimode transceivers

8. IPv4 Firewall Throughput (1518/512/64 byte UDP): 36/36/24 Gbps

9. Firewall Latency (64 bytes, UDP): 3μs or below

10. Firewall Throughput (Packet per Second): 36 Mpps or higher

11. Concurrent Sessions (TCP): at least 5.5 Million or above.

12. New Sessions/Sec: 270,000 or higher

13. Firewall Policies : 10000 or higher

14. Application control Throughput 8.5 Gbps or above

15. Intrusion Prevention Throughput Optimal traffic mix: 7 Gbps or above

16. IPsec VPN Throughput 15 Gbps or higher

17. SSL-VPN throughput 2 Gbps or higher

18. Virtual context: 8 or higher

19. Storage: 120GB

20. PTA Approved (PTA Approval to be acquired by the vendor)

21. 1 Year Standard Warranty with UTM Subscription

22. Dual power supply.


Training and Certification

24. Training Certification of Security for 2 personnel of GSCWU BWP.

PASSIVE MATERIAL

6

Rack mountable 08 Port OFDF with SC Couplers, Branded 19inch patch panel 1u with 4 x 8313 SC/SC duplex coupling SM & 8 x SC Pigtail

SM semi tight buffer,2m

12

7

Rack mountable 24 Port OFDF with SC Couplers,

Branded 19inch patch panel 1u with 24 x 8313 SC/SC duplex coupling SM & 48 x SC

Pigtail SM semi tight buffer,2m

2

8

Single Mode fiber patch cord SC/LC (3Meter Duplex

Branded Patch cable, single mode 9/125/250um - SC to LC Connector, LSZH, 1m

(Duplex 12

9

Single Mode fiber patch cord SC/LC (3Meter Duplex),

Branded Patch cable, single mode 9/125/250um - SC to LC Connector, LSZH, 3m

(Duplex 12

10 LC to LC connectors, Multimode , 3 meter cable 4

11 LC to LC connector, Single Mode 3 meter cable 2

12 Branded 24 Core 9/125/250u Unitube Cable with PE sheet, corrugated steel tape

Armored (with maximum possible redundant design)

1300 meters approx.

13 Local Good quality HDPE Pipe & warning tape (Plastic Hard pipe for underground Fiber)

meter 500

14 Local Good quality PPRC Pipe (Plastic Hard pipe unbreakable) meter 500

15 Branded 24port patch panel loaded with 24port jacks 10

16 Branded Cable Managers 10

17 Good quality pure copper Cat 6 or 6e or above Cable Roll 5


18 Connectors RJ45 Good quality 500

19

INSTALLATION & COMMISSIONING

1. Digging of Normal Soil 3 Feet

2. Boring of Mattel Road

3. Concrete Floor Cutting

4. Tuff Tile

5. Laying of HDPE Pipe underground

6. Laying of Optical Fiber

7. Filling of Normal soil 1 Feet

8. Laying of Warning Tape Underground

9. Filling of Normal soil 2Feet

10. Filling of Boring with Material

11. Filling of Concrete Floor with material

12. Filling of tuff tile with material

13. Hand hole (3X3X3) as per requirement

14. Installation of networking Cabinets

15. Splicing of Optical fiber

16. Managing of Cabinets

17. (Patch Panels, I/O, Cable Organizer)"

18. Installation of PVC Pipe on wall

19. Duct putty fitting as per required

20. Face Pates for RJ45 connectors as per requirement

21. Cable Tags as per required

1 Job

20 5KVA True Online UPS, Rack mounted with 180 minutes backup on full load.

1

Should comprise with following details with a very good repute in market.

1- Documentation CD, Installation guide, Rack Mounting brackets, Rack mounting

hardware, Rack Mounting support rails, Temperature Probe, Warranty card,

Web/SNMP Management Card

2- Battery failure notification

3- Eco mode

4- Green mode

5- LCD graphic Display

6- LED status indicators

7- Network manageable

8- Automatic self-test

9- Flash upgradeable firmware

10- SmartSlot

11- Protects connected loads from surges, spikes, lightning, and other power

disturbances

12- Generator compatible

13- Installation, configuration, commissioning and Testing

21 RACK 42 U , Universal Server RACK

1

Branded, Contemporary, sleek appearance, Strong frame structure

Good Quality with Glass door, either fixed or moveable, Built in PDU.

21 Laser Printer

1

LaserJet Network Printer

Resolution (black) FastRes 1200

Resolution technology 1200, 600 dpi

Monthly duty cycle Up to 80,000 pages

Recommended monthly page volume 750 to 4000

Print Technology Laser

Display 2-line backlit LCD graphic display

Processor Speed 1200 MHz or above

Number of print cartridges 1 (black)

Paper trays, standard 2

Connectivity standard 1 Hi-Speed USB 2.0; 1 Host USB; 1 Gigabit Network

Ready Standard (built-in Gigabit Ethernet)


Ports 1 USB 2.0; 1 Host USB; 1 Gigabit

Memory, Standard 128MB DRAM

Print speed, black (normal) Up to 40 ppm

22 Laptop

2

Core i7 Laptop 8th

generation

Cache: 8MB or above

Processor: up to 4.0 GHz

RAM: 8 GB or above (DDR-4)

Hard Disk: 1TB

Optical Drive: DVDRW

Screen Size: 15.6” FHD

Webcam/Microphone: HD

Dolby Audio

Bluetooth: 4.0

USB version: 3.1

WiFi: 802.11ac

LED Backlit

HDMI Port


(ON LETTER PAD OF THE FIRM DULY SIGNED & STAMPED)

Price Reasonability Certificate

I M/S ------------------------------ do solemnly declare that "the prices quoted to The Govt.

Sadiq College Women University, Bahawalpur are not more than the prices charged from any

other Government/Purchasing agencies. If prices are found higher or in case of any

discrepancy, the bidder hereby undertakes to refund the price charged in excess".

Certificate of Availability of Stock Quoted

(On letter pad of the firm duly signed & stamped)

I M/S-----------------------------------do solemnly declare that "the stock is available of the

quoted items in the bid and firm is bound to supply in the prescribed period"

Certificate of Physical Features of Quoted Items


I M/S --------------------------------- do solemnly declare that "the physical features of quoted

products/ items mentioned in the Technical Bid are same as in Financial Bid and Firm is

bound to supply without change".

Certificate of Inclusion of all Taxes and others


I M/S -----------------------------------do solemnly declare that "the prices quoted by our firm

are inclusive of all taxes and charges of transportation/handling/fixing/installation etc and no

extra charges will be claimed.

Certificate of Free Replacement of Items


I M/S -------------------------------------do solemnly declare that "the firm will be responsible

for the free replacement of items on his own expenses, if the same is found substandard and

or at variance with the specifications given in the tender".


TENDER TERMS AND CONDITIONS OF (GSCWU) FOR I.T ITEMS

1. The rates validity of tender will be up to 30th

June 2018 from the date of opening of

tender.

2. All pages of the bid document must be signed and stamped by the bidder.

3. GSCWU will not pay any reimbursement against any visit of vendor to the office. All

expenses will be borne by himself.

4. Dealer/Distributer/Manufacturers of the firm shall provide valid authorization and

shall also provide manufacturer’s warranty. The bidder must be authorized reseller of

the required product and must include a certificate from Authorized Distributor

confirming bidder’s reseller status.

5. The bidder shall provide supply orders of similar work from other government and

private departments. The bidder should have two (02) similar work experiences in last

six (06) years. The value of completed work should not be less than the value of

Govt. Sadiq College Women University Bahawalpur work.

6. The bidder must provide affidavit that bidder will not subcontract any part of the

project to any other vendor.

7. GSCWU reserves the right to decrease/increase the quantity without consultation as

and when required as per requirement and available budget.

8. If GSCWU deems necessary, the lowest bidder may be asked to provide sample

before awarding of any contract/order. In case, the sample of lowest bidder is

rejected, samples from the bidders will be called and contract will be awarded to

technically qualified lowest bidder.

9. The firm/supplier in question will be bound to supply the required items as a whole

consignment within 30 days after the issuance of purchase order on FOR basis.

10. The successful bidder shall execute a written agreement just after the award of the

work.

11. GSCWU may ask the lowest bidder for any clarification/providing of documents for

satisfactory evaluation of offer.

12. On finding substandard quality or lower specification as and when noticed during

process, the security deposit shall be forfeited in favor of the GSCWU. The purchaser

also reserves the right to purchase the material from elsewhere without any notice at

the risk and cost of the defaulting contractor.


13. The payment shall be subject to satisfaction of all items duly certified by the

inspection committee/user. Findings of the inspection committee will be binding on

the supplier.

14. Procurement shall be governed under the Punjab Procurement Rules, 2014.

15. In case of any dispute, the decision of the Vice Chancellor shall be final.

16. The contractor is advised to observe the safety precautions, any mishap/damage to

GSCWU BWP property due to negligence of the contractor or his representative

or any of his worker would only be borne by the contractor.

17. The bidder should not be insolvent, in receivership, bankrupt or being wound up, not

have had their business activities suspended and not be the subject of legal

proceedings for any of the foregoing.

18. The OEM should be among the top 5 vendors in terms of market share in the

respective category.

19. The OEM should have local depots in Pakistan to support the NBD delivery for the

faulty equipment.

20. For any query or appropriate estimation purpose the intended bidder can visit

GSCWU from 8:00 a.m. to 2:00 p.m. except Saturday and Sunday, before the

submission of bid.

21. The successful Bidder will depute a local resident engineer for onsite engagement to

provide operational assistance for a period of six months. The Resident Engineer will

be on the pay roll of successful bidder and expense of the Resident Engineer will be

borne by the successful bidder.


PART-II (Science Items)


TENDER DOCUMENT SPECIFICATIONS

PART-II

A Chemistry Lab Items

Sr.

No. Item Name Description Qty.

Price

(with all taxes)

1 Electronic Analytical

Balance Digital

Microprocessor Controlled with Latest Uni Block Technology, Uni Block

designs replaces 70 parts of Electromagnetic balances and ensures stable results.

Technical Specification:

Weighting Capacity: 220gm

Minimum display: 0.1mg

Pan size (mm): Ø91 approx.

Features: - Automatic calibration by pressing keys with internal calibration

weight

- Easy setting, expanded piece counting function comparator function, formulation modes

- Windows direct communication function, send balance data

to excel without any data software with optional RS232C interface. Complete unit, operated on 220Volts.

Shimadzu, Japan or equivalent

01

2 Electronic balance digital

top loading

with Uni-block technology,

One single block non-breakable, this brings various advantages fast

Response, high stability, long life operation, metal housing:

Readability: 0.001gm Capacity: 620gm Built in under weighing hook,

piece counting function built in, RS 232C Data interface,overlaod protection, windows direct function, No software required, stainless steel

pan 108x105mm with draft shield, operated on 220 volts,

Shimadzu, Japan or Equivalent

01

3 pH Meters

Digital Bench Model Microprocessor Controlled With parallel Temperature indication, PH Range -2.0 to 20.0 ±0.005pH,

PH Resolution 0.005pH, MV Range ±1200.0mV, Accuracy mV ±-

0.3mv, Automatic Temperature Compensation, Temperature Range

–5 to +105.0°C, Temperature accuracy ±0.1°C with two/three

Point Calibration System, Battery operated as well as operated With 220 Volts without electrode

Germany or equivalent

01

4 Double Distillation Water

Still

Made of borosilicate glass, ideal for producing high quality water Incorporates several security system for automatic operation to work

continuously

Cooling water outlet by rubber tube. The condensed water not Flowing

through the cooling water outlet. Energy saving through distillation of

preheated cooling water

Specification: Capacity: 4 Litre/hour

pH: Depends on tap water inlet 5.5-7

Conductivity: 1.5µS/cm Cooling water: 1,2l/min.

Operated on 220V, Model BIDISTILLER Bi-Hydro 4.1,

Spain (Europe) or equivalent

01

5

Micropipettes Adjustable built to last constructed of stainless steel and PVDF with unique dry seal technology thick body robust accurate and precise individually calibrated, Tip Holders and Tip Ejectors are fully Autocleavable, Up to 50% deduction of pipetting and purge forces Ranges as

follows:-

5a 2 to 20µl, Measuring Range 2 to 20µl, Accuracy ±0.060µl

Gilson (France) or Equivalent 10

5b 20 to 200µl, Measuring Range 20 to 200µl, Accuracy ±0.30µl


5c 100 to 1000µl, Measuring Range 100 to 1000µl, Accuracy ±1.5µl


6 Autoclave Digital

Microprocessor

Controlled Vertical Unit Temperature Range 105 to 135º C Interior

Chamber Stainless steel, capacity 110 Lit interior chamber dimension

420x795Dmm, with Built in Timer 1 to 250 Minutes, Pressure Gauge 0 to 0.4 mpa,

01


Sr.


Price

(with all taxes)

Selected Modes for Liquid and Solids, Forced cooling Fan as standard function, after sterilization, reduce the pressure Without exhaust by

forced cooling fan built-in as standard. User-Friendly Features:

Electromechanical Lock system, Double Interlock, Auto Cut-off function, Process display, Complete with two stainless Steel wire Baskets operated

on

220 Volts with following Features: a. Dual Sensing Interlock mechanism. b. Over-pressure power cut-off

c. Sterilizing time counting timer d. Over-temperature power cut-off

e. Heater malfunction checker. f. Temperature sensor wire breakage detector.

g. Securely closed lid check function. h. Exhaust bottle ready-to-use

check system. i. Lack-of-water prevention device. j. Electric leakage breaker and over

current detector.

Pressure Safety valve. Complete Unit as above

Hirayama (Japan) or equivalent

7 Potentiostat/Galvanostat

Zero resistance ammeter · 2- or 3- or 4-electrode configuration· Floating

(isolated from earth) or earth ground · Maximum potential: ±10 V · Maximum current: ±250 mA continuous, ±350 mA peak 2-3 weeks

ARO, or 2 weeks after receipt of payments, whichever is later. ·

Compliance Voltage: ±13 V· Potentiostat rise time: < 1 us, 0.8 us typical · Potentiostat bandwidth (-3 dB): 1 MHz· Applied potential ranges: ±10

mV, ±50 mV, ±100 mV, ±650 mV, ±3.276 V, ±6.553 V, ±10 V· Applied

potential resolution: 0.0015% of potential range· Applied potential accuracy: ±1 mV, ±0.01% of scale· Applied potential noise: < 10 uV rms

· Measured current range: ±10 pA to ±0.25 A in 12 ranges· Measured

current resolution: 0.0015% of current range, minimum 0.3 fA · Current measurement accuracy: 0.2% if current range >=1e-6 A/V, 1%otherwise·

Input bias current: < 20 pAGalvanostat:· Galvanostat applied current

range: 3 nA – 250 mA· Applied current accuracy: 20 pA ±0.2% if > 3e-7A, ±1% otherwise· Applied current resolution: 0.03% of applied current

range· Measured potential range: ±0.025 V, ±0.1 V, ±0.25 V, ±1 V±2.5

V, ±10 VMeasured potential resolution: 0.0015% of measured range Electrometer:· Reference electrode input impedance: 1e12 ohm·

Reference electrode input bandwidth: 10 MHz

Reference electrode input bias current: <= 10 pA @ 25°CWaveform Generation and Data Acquisition:· Fast waveform update: 10 MHz @ 16-

bit· Fast data acquisition: dual channel 16-bit ADC, 1,000,000

samples/sec simultaneously· External signal recording channel at maximum 1 MHz sampling rateExperimental Parameters:· CV and LSV

scan rate: 0.000001 to 10,000 V/s· Potential increment during scan: 0.1

mV @ 1,000 V/s CA and CC pulse width: 0.0001 to 1000 sec· CA and CC minimum sample interval: 1 us· True integrator for CC· DPV and

NPV pulse width: 0.001 to 10 sec· SWV frequency: 1 to 100 kHz· i-t

sample interval: minimum 1 us· ACV frequency: 0.1 to 10 kHz· SHACV frequency: 0.1 to 5 kHz· FTACV frequency: 0.1 to 50 Hz, simultaneously

acquire 1st, 2nd, 3rd, 4th,5th, and 6th harmonics ACV data· IMP

frequency: 0.00001 to 1 MHz· IMP amplitude: 0.00001 V to 0.7 V rmsOther Features:· Automatic and manual iR compensation· Current

measurement bias: full range with 16-bit resolution, 0.003%accuracy· Potential measurement bias: ±10V with 16-bit resolution, 0.003%

accuracy· External potential input· Potential and current analog output·

Programmable potential filter cutoff: 1.5 MHz, 150 KHz, 15 KHz, 1.5 KHz,150 Hz, 15 Hz, 1.5 Hz, 0.15 Hz· Programmable signal filter cutoff:

1.5 MHz, 150 KHz, 15 KHz, 1.5 KHz, 150Hz, 15 Hz, 1.5 Hz, 0.15 Hz·

RDE control output (Model 630E and up): 0-10V (corresponding to 0-10000 rpm), 16-bit, 0.003% accuracy· Digital input/output lines

programmable through macro command· Flash memory for quick

software update· Serial port or USB port electable for data communication· Cell control: purge, stir, knock· CV simulation and

fitting program, user-defined mechanisms· Impedance simulation and

fitting program· Maximum data length: 256K-16384K selectable· Dimensions: 14.25”(W) ´ 9.25”(D) ´ 4.75”(H)· Weight: 12 lb. Software

Features :· Windows-based software· Multi-document interface· Open,

save, delete, list, conversion, and print files· Run, macro, iR mpensation, filtering, RDE control, preconditioning, step functions, and cell control·

Data plot, overlay and parallel plots, x-y plot, ip~v plot, ip~v1/2 plot,

Ep~log vplot, semilog plot, 3D interactive Nyquist plot and Bode plot· Graphics options, color and font selections· Smoothing, derivatives,

integration, semi-derivative and semi-integral,interpolation, baseline

fitting & subtraction, linear baseline correction, datapoint removing, data point modification, background subtraction, signal averaging,

mathematical oper· Calibration curve, standard addition, data file report,

01


Sr.


Price

(with all taxes)

concentration - time dependence report and plot · Integrated digital CV simulator and fitting program, user defined mechanisms· Integrated

impedance simulator and fitting program· Data information, data listing,

equations, clock· User customizable toolbar, status bar· Context sensitive help· Maximum data length: 256K-16,384K selectable Accessory:· User's

manual in .pdf format, no printed manua· Electrode leads· USB

communication cable· Power cord

USA or equivalent

8 Vacuum Drying oven

vacuum oven VO shows off all its strength – at the same time it can

handle heat-sensitive or oxygen-sensitive substances and materials such

as cosmetics, food, clocks, books or PCBs and other electronic

components with unparalleled gentleness when drying. The direct contact

between chamber load and the heatable and removable thermal shelves

guarantees in all vacuum oven models a quick and even temperature

control without loss of heat.

Temperature range 5°C above ambient up to +200°C

fuzzy-supported MLC (Multi-Level-Controlling) microprocessor controller adapting its performance to the volume for each thermoshelf

Temperature measured through 4-wire Pt100 sensor individually for each thermoshelf

integrated timer for tempering and pressure (vacuum) profiles

Digital electronic pressure control through solenoid valves

adjustment range from 10 mbar to 1100 mbar - digital (LED)

setting accuracy 1 mbar

Rapid air intake for door opening (door is blocked under vacuum) programme reactivation at stored values

vacuum drying process (vacuum cycles) is continued after power failure

Multiple Over temperature Protection

Textured Stainless Steel Casing

hermetically welded stainless steel interior of extremely corrosion-

resistant stainless steel, material 1.4404

Capacity 29 Lit, interior dimension: 385 x 305 x 250 mm, Operated on 220volts,


01

9 Melting Point Apparatus

(Digital)

Digital selection & display of temperature - High accuracy Easy to operate with plateau facility - Ideal for educational use

Supplied with calibration certificate Technical Specification:

Number of samples 2 Temperature range Ambient to 300°C Temperature accuracy ± 1.0°C at 20°C, ± 2.5°C at 300°C Display

Three digit LED Temperature resolution 1°CSensor Platinum

resistance PT100 Ramp rates 20°C per minute to plateau 20°C per minute to melt Dimensions (w x d x h) 160 x 220 x 170 mm Net weight

1.8 kg Electrical supply 230V, 50Hz, 75WComplete unit with pack of

100 melting point tubes, closed at both ends,

England or equivalent

01

10 Micro Centrifuge

Machine Table Top

high speed range from 200 to 14800 rpm, maximum RCF 16163, with

brushless Motor Drive, Microprocessor controlled Digital Bright

Display of Speed or RCF, Pre selection speed or G force, Timer range 10

Sec to 99 minute with short run or continuous run Last run memory 2

acceleration & deceleration curves soft or fast Motorized Lid Lock, Auto Lid Open, emergency lid lock release, Minimal temperature increase

during run, complete with Angle Rotor capacity 24 x 1.5 ml, complete

unit operated on 220 Volts,


01

11 Shaking Water Bath

Basic class for standard temperature control tasks, the Excellent version

provides precise test procedures with a maximum of safety: electronic over temperature control and a wide range of visual and acoustic signals.

Temperature range min. 5 °C above ambient up to +95 °C with

additional boiling mode (+100 °C)

State-of-the-art control technology of the Basic and models

Microprocessor PID-temperature controller with

integrated auto diagnostic system with fault indicator

integrated digital timer from 1 min. to 99,59 hours

Over temperature Protection (double)

Interior Stainless Steel Tank & Textured Stainless Steel Casing

Fitted With Gabled Cover

Operated on 220volts, WNB Series.

Capacity 14 Lit., interior dimension 350x290x140mm

shaking speed 10-150 stroke/minute

capacity to holds 6 Flasks of 250ml Complete set


01


Sr.


Price

(with all taxes)

12 Ag/Agcl (saturated KCl) Ag/Agcl (saturated KCl) Electrode

Japan or Equivalent 01

13 Distillation Apparatus

Complete set, round bottom flask 5Litre,

compatible heating and stirring mantle, compatible still head adopter, condenser,

receiver, and receiving flask

UK/USA or Equivalent

01

14 Magnetic Stirrer with Hot

Plate

Temperature range up to 370°C, Variable Speed Control upto 1200rpm

Heating Plate Ø: 155mm,

Stirring capacity: 15 liter Power: 630 Watt, with PTFE follower, operated on 220 volts,

Italy or equivalent

01

15

15a Rotary

evaporator

Rotary Evaporator Features:

- With built in large digital 3.5” LCD display which

indicates rotation speed, heating bath temperature and vapour temperature (vapour temperature sensor required)

- With built in Timer

- Reduce your process times up to 30% - The chemical resistant vacuum seal reduces your spare

parts budget up to 75% with prolonged operational lifespan

- Savings at the same high level are possible due to the long service life vapour tube.

With additional number of safety features

Affordable model with hand lift, Drive DC motor with electronic speed control, rotation speed range 20 – 280 rpm

and temperature range of heating bath 20 – 210°C, temperature

accuracy ±1°C, electronic heating bath temperature control, overheat cut-off protection 5°C over set temperature, heating

capacity of water bath 1300 Watt, volume of heating bath 4.5 Litres

with glass Set G-1 with diagonal condenser, complete

Unit operated on 220 Volts

01

15b Vacuum Pump

Vacuum Pump PTFE Diaphragm Chemistry Design two Stage provides

the advantageous combination of High Pumping Speed and low Ultimate vacuum Suitable for Rotary Evaporators, all pumping parts in contact

with pumped media are made of Chemically Resistant Flour plastics .

PTFE Diaphragms increase Reliability and Extended Operation Life.

Technical Specification:

Number of Head / Stages 2

Capacity: 15 lit/minute approx

Maximum Pumping Speed 0.75 m3h/0.9 m3h

Ultimate Vacuum 12 mbar Ultimate Vacuum with Gas Ballast 20 mbar

Operated on 220 Volts


01

15c Chiller

Chiller with air-cooled refrigeration and built in circulation pump, Evaporator Tank and housing all made of stainless

steel, digital temperature adjustment and digital temperature

display, level indicator with sight glass, built in micro-

processor controller with a large temperature display, LED

indicators for pump cooling and heating. Technical Features:

Operating temperature range: -20 to 40°C

Temperature adjustment: Digital Temperature indication: Digital

internal temperature sensor: PT100

Resolution of display: 0.1K Refrigeration machine: air-cooled, CFC-free

Circulation Pump: Built in

Max. delivery (pressure): 20 l/min. Complete unit as above, Model Minichiller

01

16 Deionizer

Single cartridge, wall mounted to deionize water with built in

conductivity meter, Output 45 Lit/hour, pure water quality – 20 us/cm

depends on water quality, operated on 220 Volts.


01

17 UV/Vis

Spectrophotometer

Double beam spectrophotometer with Split Beam Technology (SBT)

Features • Outstanding long-term stability, excellent signal-to-noise ratio and best

energy throughput

• Holmium oxide filter for automatic wavelength calibration • Quartz coated optics

• Highly precise imaging conditions due to aspheric optics

01


Sr.


Price

(with all taxes)

• Second cell position for measuring turbid samples Mode: Absorption, Transmission,

Sample Compartment dimensions

(W x H x D): 364 x 185 x 260 mm Wavelength range: 190—1100 nm

Spectral bandwidth: Fix 1.4 nm

Scanning speed: 12000 nm/min Technical standard:

Photometric display

Range of the software: to 8A Photometric Range: -3A to 3A

Spectral bandwidth: fix 1.4 nm

UV- Resolution (toluene-hexane): ≥ 1.6 Wavelength accuracy

(Deuterium line at 656nm): ± 0.1 nm

Wavelength reproducibility (with Holmium oxide filter): ≤0.02 nm

Photometric accuracy: ± 0.003 A

Photometric reproducibility: ≤ 0.0005 A Stray light ≤ 0.03 % T

Baseline stability at 500 nm: ≤ 0.0001 (RMS)

Long-term stability at 500 nm: ± 0.0005 A/h Scanning speed: 12000 nm/min

Complete with Software, Computer and Printer

Germany or Equivalent

18 Glassy Carbon Electrode Glassy Carbon electrode

(3mm dia) Pt wire counter 01

19 Orbital Shaker Digital

Compact, flat laboratory shakers available with orbital motion, adjustable timer, digital display of speed, protected against overload and intrinsically

safe operation.

Shaking motion: orbital Shaking movement: 20 mm

Speed range infinitely

adjustable: 30 – 500 rpm Speed display: Digital

Dimensions (WxDxH) 320 x 125 x 375 mm

Complete with Platform and fixing Clips 2-Nos each 100, 250, 500ml


01

20 Heating Mantle

Control method: proportional voltage control Case construction: steel,

with chemically, Resistant powder coating. Thermal insulation: asbestos-free ceramic cool, (Fiber glass). Heating element: Ni-chrome wire.

Heating element temperature range upto 450ºC max. Capacity 5000ml,

combined heating stirring.

Korea or equivalent

01

21 Spectrophotometer

Visible

digital microprocessor controlled range 320-1000nm, zero and blank

setting automatic, bandwidth 6nm, complete unit with 10cm path length glass cells, complete set operated on 220 Volts

Japan or equivalent

01

22 Fume Hood

With built in Gas & Water Valves

Features:

• Chemical-resistant phenolic resin construction (interior

and exterior) • Different choice of worktops suitable for a wide range of

applications

• Clear tempered safety glass sash utilizes counter weights for smooth and effortless operation.

• Visual and acoustic airflow alarms.

Specifications: External Dimension (L x H x D mm): 1200 x 875 x 1500

Working Zone (L x H x D mm): 1120 x 680 x 1200

Recommended Maximum Exhaust Required Fume Hood Air volume for

minimum face velocity Exhaust Air Volume of 0.5 m/s or 100 fpm at full-open 1170 cmh / 690 cfm hood sash position:

Recommended Minimum Exhaust Required Fume Hood Air volume for

minimum face velocity Exhaust Air Volume of 0.5 m/s or 100 fpm at

half-open 585 cmh / 344 cfm

Hood sash position:

Inner Exhaust Outlet Diameter: 252 mm / 10.0”

Outer Exhaust Outlet Diameter: 266 mm / 10.5”

01


Sr.


Price

(with all taxes)

Light Intensity at Work Surface: 780 Lux / 72 foot candes Construction: Main body: Phenolic resin laminates

Support frame: Aluminum extrusions with an oven-baked epoxy powder

coated finish. Interior baffle system: Phenolic resin laminates

Airfoil: Stainless steel grade 304

Complete unit with base storage cabinet

Singapore or equivalent

TERMS AND CONDITIONS OF GSCWU FOR SCIENCE ITEMS

1. The rates validity of tender will be up to 30

th June 2018 from the date of opening of tender. Prices

of individual items must be quoted separately inclusive all taxes

2. All pages of the bid document must be signed and stamped by the bidder.

3. GSCWU will not pay any reimbursement against any visit of vendor to the office. All expenses will

be born by himself.

4. Dealer/Distributer/Manufacturers of the firm shall provide valid authorization and shall also provide

manufacturer’s warranty.

5. The firm shall provide supply orders of similar work from other government departments.

6. GSCWU reserves the right to decrease /increase the quantity without consultation as and when

required as per requirement and available budget.

7. If GSCWU deems necessary, the lowest bidder may be asked to provide sample before awarding of

any contract/order.

8. The firm/supplier in question will be bound to supply the required items as a whole consignment

within 15 days after the issuance of purchase order on FOR basis.

9. The successful bidder shall execute a written agreement just after the award of the work.

10. GSCWU may ask the lowest bidder for any clarification/providing of documents for satisfactory

evaluation of offer.

11. On finding substandard quality or lower specification as and when noticed during process, the

security deposit shall be forfeited in favor of the GSCWU. The purchaser also reserves the right to

purchase the material from elsewhere without any notice at the risk and cost of the defaulting

contractor.

12. The payment shall be subject to satisfaction of all items duly certified by the inspection

committee/user. Findings of the inspection committee will be binding on the supplier.

13. Procurement shall be governed under the Punjab Procurement Rules, 2014.

14. In case of any dispute, the decision of the Vice Chancellor shall be final.

Documents

Office of the Chairperson Purchase Committee 1 of 19 062 ... · Office of the Chairperson Purchase Committee Page 4 of 19 062-2284809 SPECIFICATIONS I.T Items Price with all Sr.#