Upload
hoangkhanh
View
218
Download
5
Embed Size (px)
Citation preview
6220KEMLITE® MOLDINGS ONE-PIECE MOLDINGS, TWO-PIECE MOLDINGS & RIVETS
technical data
When installing outside and inside angles to FRP panels, use Crane Advanced Polymer Panel Adhesive. Acrylic, epoxy or urethane based adhesives should be used to provide an adequate bond. Silicone sealant is not meant to be used as an adhesive and will not properly bond the angle to the FRP panel.
REV. 31 | 05/18
PRODUCTFor professional looking panel installations, and maximum moisture sealing effectiveness, use Kemlite one-piece, non-staining, polypropylene moldings.
PURPOSEFor use with panel thicknesses 0.075” and 0.09”. For 0.12” panels use the 2 piece moldings.NOTE: Images are not drawn to scale and are depicted in inches
STANDARD ONE-PIECE POLYPROPYLENE MOLDINGS
PRODUCTNon-staining nylon drive rivets in matching panel colors are designed for quick and easy installation using only a hammer and drill. When used with silicone sealants, drive rivets maintain an effective moisture seal as well as providing excellent mechanical fastening for panels.
PURPOSESee table for rivet size and corresponding panel thickness.
STANDARD NYLON DRIVE RIVETS
PANEL THICKNESSRIVET
LENGTHAVAILABLE COLORS
0.09" - 0.125"2.29mm - 3.18mm
0.75"19.05mm
White, Cream, Beige, Silver,
and Gray
0.09" - 0.25"2.29mm - 6.35mm
1"25.40mm
White
0.25" - 0.50"6.35mm - 12.70mm
1.5" 38.0mm
White
.11
see tablefor length
.500
.095
.045
.870
.120
.550
.80
.100
.0401.420
.085
1.475
1.475
.100
.035.865
.545
.550
.100
.035.700
DIVISION BAR | DB
OUTSIDE CORNER | OC
INSIDE CORNER | IC
CAP | CP
.085
1.450
1.450
INSIDE ANGLE | IA OUTSIDE ANGLE | OA
KEMLITE® MOLDINGS LAMINATED MOLDINGS
PRODUCTFor professional looking panel installations, and maximum moisture sealing effectiveness, use Kemlite one-piece, non-staining, pvc moldings.
PURPOSEFor use with laminated panel thicknesses up to 0.437”.
STANDARD ONE-PIECE POLYPROPYLENE MOLDINGS
PRODUCTFor professional looking and convenient installations, use two-piece snap-on trim, non-staining, polypropylene moldings. Available in white only. Use for all thicknesses.
PURPOSEImproved installation time. Panel and molding can be installed in separate operations. Screws can be used to secure base and panel. Holes must be oversized.
TWO-PIECE SURFACE MOUNT MOLDINGS
DIVISION BAR | DB OUTSIDE CORNER | OCINSIDE CORNER | IC
CAP | CP
0.750"
0.440"
1.720"
0.809"
0.445"
0.920"
1.230"
0.690"
1.320"
0.440"
0.970"
1.235"
0.720"
1.500"
.050"
.320"
.150".455"
.110"
T-BAR | TB *
0.420" * T-Bar is extruded Polypropylene
Inside and Outside Angles are also available for Kemply Laminated installations. Please refer to Standard One-Piece Polypropylene Moldings on the other side of this page for dimensions
DIVISION BAR | DB OUTSIDE CORNER | OCINSIDE CORNER | OC
1.575"
0.065"
0.125"
1.30"
0.73"
0.73"
1.46" 1.00"
0.95"
part b
part a part b
part a
part a
part b
cranecomposites.com | 1.800.435.0080 | 1.815.467.8666 [fax] | [email protected] believe all information given is accurate. It is offered in good faith, but without guarantee. Since conditions of use are beyond our control, all risks are assumed by the user. Nothing herein shall be construed as a recommendation for uses which infringe on valid patents or as extending a license under valid patents. See our most current SDS at cranecomposites.com/sds.html prior to working with our products.
A global leading provider of resilient wall and ceiling coverings. Kemlite® was established in 1954 and the company changed names to Crane Composites in 2007. Crane Composites is headquartered in Channahon, IL and all our products are manufactured in the United States. We work with hundreds of distributors, ensuring our products are easily accessible and readily available to our customers. The following are trademarks of Crane Composites, Inc. or a related company: Glasbord, Kemlite, Kemply, Surfaseal, Sanigrid, Silhouette Trims and Varietex
6220 | REV. 31 | 5.18 (8299)