Upload
alphamatrix01
View
228
Download
0
Embed Size (px)
Citation preview
8/3/2019 One Sheet Sampan
1/5
Simplicity is not achieved by adding simplifications, but by removing complications.
A sampan boat is typical to South East Asian countries, where many seemingly different boat types in several countries
appear under the same common name.
"Sampan" literally means "three planks". This explains the many boat types called by the same name. Boats, that at least
originally were made of just three planks. So calling Western piroques, batteaus (sharp sterned dory), my "Prism" or my
"Dug" sampans would not be incorrect.
The "One sheet Sampan" presented here follows the ideas of a cargo sampan from canals of Vietnam. She exhibits theinteresting concave side sections typical to many sampan types. At least to my eye the concavity is typical to sampans
:-) The concavity of the bottom edges also helps a lot in placing the boat parts on the plywood, as You can see on the
drawing below. The convex bottom edges of side pieces match the concave edges of the bottom piece.
heet Sampan file:///C:/Users/Main/Desktop/Boat%20Plans%20June%205%20
2/9/2010
8/3/2019 One Sheet Sampan
2/5
One can hardly think of a simpler boat in terms of building ease and materials usage, yet giving a lot of load carrying
capacity and stability. She measures 7'4" x 3'3", so she is wide enough to scull. She displaces about 800 lbs just before
flooding. At 250 lbs displacement, that is, one person, her freeboard is 7".
Here is the "One sheet Sampan" .hul file for those interested.
Since the boat really consists of only three parts (transoms have been left out as unnecessary complications), plywood
cutting is very easy. The boat bottom comes from the middle of the ply, reaching from end to end. The sides are cut in
two pieces each. The rest of the ply is used for butt blocks and quarter knees. Not much more than sawdust is left over.
One might ask "why not cut single piece sides, wouldn't that be simpler?" Yes, it would be simpler. But it would limit the
bottom plus the side widths to the width of the plywood sheet, 48". A good combination would be bottom 28", both sides10". But by splitting the sides in two we now will get a bottom of 30", both sides 13", altogether 56". Which is a much
bigger boat. In my opinion it is worth doing two butt joints instead of having a too small boat.
heet Sampan file:///C:/Users/Main/Desktop/Boat%20Plans%20June%205%20
2/9/2010
8/3/2019 One Sheet Sampan
3/5
One can, of course, do the cutting "other way round". Make the sides out of single pieces, and have the butt seam on the
bottom.
Or If You want to spare two sheets, You can make a sampan without any butt seams. Take the bottom measurements
from the upper diagram, the side measurements from the diagram below.
The building sequence is simple and straight forward.
heet Sampan file:///C:/Users/Main/Desktop/Boat%20Plans%20June%205%20
2/9/2010
8/3/2019 One Sheet Sampan
4/5
First draw lines to divide the plywood sheet into eight equal squares,
each 24" x 24". Measure and mark points A, B, C, D, E and F on the
lines according to the measurements given in the drawing above.
Nail two small nails at points A and B. Put a thin batten above the
nails, pull the center of the batten towards You until the edge of the
batten reaches point C. Draw the curve A-C-B along the batten.
Nail a nail at point D. Bend the batten between the nails at D and B
in such a way, that it crosses the plywood edge at right angles at
point F. Draw the curve D-B-F along the batten.
Mark 4" wide butt blocks at the center line of the plywood (drawn in
pale blue in the drawing above).
Repeat the procedure for the curve D-A-E.
Repeat the whole A to F procedure on the other side of the plywood.
All lines marked on the plywood.
Pieces sawn along the lines.
And rearranged to "boat shape".
And assembled into a boat.
The sides were first put together with butt blocks, then the bottom and sides using the "2 x 2 blocks and drywall screws"
method. The internal distance between the tops of sides in the middle of the boat is 38 1/2", set this with a piece of
board.
heet Sampan file:///C:/Users/Main/Desktop/Boat%20Plans%20June%205%20
2/9/2010
8/3/2019 One Sheet Sampan
5/5
The gunwales, and strips in place of transoms are 1" x 1" pine, the seat a length of 1" x 8" just glued between the sides.
The quarter knees have been glued on top of the gunwale battens.
Paintwork finished, ready to go on a maiden voyage.
But what's stalling her?
:-) Did I manage to fool You?
She's not a full size boat, but a 1 to 2 model.
I have more than enough small boats
already.
But mind You. Making a half size model is
just as much work as making a full size
boat, making a smaller model is much more
work. So If You want to build a boat, the
easiest way is to build a full size boat tostart with.
Top of the page.
Back to main page.
heet Sampan file:///C:/Users/Main/Desktop/Boat%20Plans%20June%205%20