OPCOM3105 Commands Notebook 200811

www.raisecom.com

OPCOM3105 Commands Notebook

Legal Notices

Raisecom Technology Co., Ltd makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Raisecom Technology Co., Ltd shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Warranty.

A copy of the specific warranty terms applicable to your Raisecom product and replacement parts can be obtained from Service Office.

Restricted Rights Legend.

All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Raisecom Technology Co., Ltd. The information contained in this document is subject to change without notice.

Copyright Notices.

Copyright ©2008 Raisecom. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in Writing from Raisecom Technology Co., Ltd.

Trademark Notices

is the trademark of Raisecom Technology Co., Ltd.

Java™ is a U.S. trademark of Sun Microsystems, Inc.

Microsoft® is a U.S. registered trademark of Microsoft Corporation.

Windows NT® is a U.S. registered trademark of Microsoft Corporation.

Windows® 2000 is a U.S. registered trademark of Microsoft Corporation.

Windows® XP is a U.S. registered trademark of Microsoft Corporation.

Windows® and MS Windows® are U.S. registered trademarks of

Microsoft Corporation.

Contact Information

Technical Assistance Center

The Raisecom TAC is available to all customers who need technical assistance with a Raisecom product, technology, or, solution. You can communicate with us through the following methods:

Address: 2nd Floor, South Building of Rainbow Plaza, No.11 Shangdi Information Road,

Haidian District, Beijing 100085

Tel: +86-10-82883305

Fax: +86-10-82883056

World Wide Web

You can access the most current Raisecom product information on the World Wide Web at the following URL:

http://www.raisecom.com

Feedback

Comments and questions about how the OPCOM3105 software works are welcomed. Please review the FAQ in the related manual, and if your question is not covered, send email by using the following web page:

http://www.raisecom.com/en/xcontactus/contactus.htm.

If you have comments on the OPCOM3105 specification, instead of the web page above, please send comments to:

[email protected]

We hope to hear from you!

CONTENTS Release Notes------------------------------------------------------------------------------------------------- 7 Chapter 1 How to Use the Command Line------------------------------------------------------- 1

1.1 Software and hardware environment ---------------------------------------------------------------------------------1 1.2 Command line modes ------------------------------------------------------------------------------------------------------1 1.3 Command line format annotation --------------------------------------------------------------------------------------1

Chapter 2 Definitions of Command Line --------------------------------------------------------- 2 2.1 Relevant commands of SDH crossconnect timeslot ------------------------------------------------------------2

2.1.1 sdh crossconnect (vc12|vc3) ------------------------------------------------------------------------------------------------------------ 2 2.1.2 sdh crossconnect (vc12|vc3) TSSTRING-------------------------------------------------------------------------------------------- 2 2.1.3 show sdh crossconnect------------------------------------------------------------------------------------------------------------------- 3 2.1.4 timeslot add sdh ---------------------------------------------------------------------------------------------------------------------------- 3 2.1.5 timeslot delete sdh------------------------------------------------------------------------------------------------------------------------- 4 2.1.6 show timeslot-------------------------------------------------------------------------------------------------------------------------------- 5 2.1.7 show interface timeslot ------------------------------------------------------------------------------------------------------------------- 5

2.2 Relevant commands of protection-------------------------------------------------------------------------------------6 2.2.1 protect-switch enable --------------------------------------------------------------------------------------------------------------------- 6 2.2.2 protect-switch disable --------------------------------------------------------------------------------------------------------------------- 6 2.2.3 aps-restore-time ---------------------------------------------------------------------------------------------------------------------------- 7 2.2.4 aps-mode------------------------------------------------------------------------------------------------------------------------------------- 7 2.2.5 force-switch---------------------------------------------------------------------------------------------------------------------------------- 8 2.2.6 manual-switch------------------------------------------------------------------------------------------------------------------------------- 9 2.2.7 show aps ------------------------------------------------------------------------------------------------------------------------------------- 9

2.3 Commands of SDH interface ------------------------------------------------------------------------------------------10 2.3.1 interface stm1-opt------------------------------------------------------------------------------------------------------------------------ 10 2.3.2 sdh description---------------------------------------------------------------------------------------------------------------------------- 10 2.3.3 loopback-------------------------------------------------------------------------------------------------------------------------------------11 2.3.4 als ---------------------------------------------------------------------------------------------------------------------------------------------11 2.3.5 clear-statistic ------------------------------------------------------------------------------------------------------------------------------ 12 2.3.6 sdh aupje-threshold --------------------------------------------------------------------------------------------------------------------- 12 2.3.7 sdh es-threshold-------------------------------------------------------------------------------------------------------------------------- 13 2.3.8 sdh msais-insert -------------------------------------------------------------------------------------------------------------------------- 13 2.3.9 sdh tuais-insert --------------------------------------------------------------------------------------------------------------------------- 14 2.3.10 sdh overhead c2 ------------------------------------------------------------------------------------------------------------------------ 15 2.3.11 sdh overhead j0 ------------------------------------------------------------------------------------------------------------------------- 16 2.3.12 sdh overhead j0-mode ---------------------------------------------------------------------------------------------------------------- 16 2.3.13 sdh overhead j1------------------------------------------------------------------------------------------------------------------------- 17 2.3.14 sdh overhead j1-mode ---------------------------------------------------------------------------------------------------------------- 18 2.3.15 sdh overhead k1 ------------------------------------------------------------------------------------------------------------------------ 18 2.3.16 sdh overhead k2 ------------------------------------------------------------------------------------------------------------------------ 19 2.3.17 sdh overhead v5 ------------------------------------------------------------------------------------------------------------------------ 19 2.3.18 sdh overhead k4 ------------------------------------------------------------------------------------------------------------------------ 20 2.3.19 sdh sd-threshold ------------------------------------------------------------------------------------------------------------------------ 20 2.3.20 show sdh-alarm ------------------------------------------------------------------------------------------------------------------------- 21 2.3.21 show interface timeslot-occupy ----------------------------------------------------------------------------------------------------- 21 2.3.22 show interface stm1 ------------------------------------------------------------------------------------------------------------------- 22 2.3.23 show interface--------------------------------------------------------------------------------------------------------------------------- 23

2.4 Commands of E1 interface ---------------------------------------------------------------------------------------------23 2.4.1 interface e1 -------------------------------------------------------------------------------------------------------------------------------- 23 2.4.2 e1-loopback ------------------------------------------------------------------------------------------------------------------------------- 24 2.4.3 show interface ---------------------------------------------------------------------------------------------------------------------------- 24

2.5 Commands of ETH interface-------------------------------------------------------------------------------------------25 2.5.1 automdi ------------------------------------------------------------------------------------------------------------------------------------- 25 2.5.2 autonegotiate------------------------------------------------------------------------------------------------------------------------------ 25 2.5.3 clear statistic------------------------------------------------------------------------------------------------------------------------------- 26 2.5.4 speed (10|100|1000) duplex (full-duplex|half-duplex)--------------------------------------------------------------------------- 26 2.5.5 interface eth ------------------------------------------------------------------------------------------------------------------------------- 27 2.5.6 show interface ---------------------------------------------------------------------------------------------------------------------------- 27 2.5.7 shutdown ----------------------------------------------------------------------------------------------------------------------------------- 28

2.6 Commands of EOS interface ------------------------------------------------------------------------------------------28 2.6.1 interface eos------------------------------------------------------------------------------------------------------------------------------- 28 2.6.2 clear statistic------------------------------------------------------------------------------------------------------------------------------- 29 2.6.3 encapsulation ----------------------------------------------------------------------------------------------------------------------------- 29

2.6.4 gfp-fcs --------------------------------------------------------------------------------------------------------------------------------------- 30 2.6.5 lcas ------------------------------------------------------------------------------------------------------------------------------------------ 30 2.6.6 show interface eos----------------------------------------------------------------------------------------------------------------------- 31 2.6.7 show interface ---------------------------------------------------------------------------------------------------------------------------- 31

2.7 Commands of ETH switchport ----------------------------------------------------------------------------------------32 2.7.1 rate-limit ------------------------------------------------------------------------------------------------------------------------------------ 32 2.7.2 show rate-limit ---------------------------------------------------------------------------------------------------------------------------- 32 2.7.3 strom-control-global --------------------------------------------------------------------------------------------------------------------- 33 2.7.4 storm-control-global rate --------------------------------------------------------------------------------------------------------------- 34 2.7.5 show strom-control-global ------------------------------------------------------------------------------------------------------------- 34 2.7.6 vlan ------------------------------------------------------------------------------------------------------------------------------------------ 34 2.7.7 state ----------------------------------------------------------------------------------------------------------------------------------------- 35 2.7.8 interface switchport ---------------------------------------------------------------------------------------------------------------------- 35 2.7.9 switchport ---------------------------------------------------------------------------------------------------------------------------------- 36 2.7.10 switchport access vlan ---------------------------------------------------------------------------------------------------------------- 37 2.7.11 switchport dot1q-tunnel vlan --------------------------------------------------------------------------------------------------------- 37 2.7.12 switchport trunk allowed vlan list --------------------------------------------------------------------------------------------------- 37 2.7.13 switchport hybrid allowed vlan ------------------------------------------------------------------------------------------------------ 38 2.7.14 switchport mode ------------------------------------------------------------------------------------------------------------------------ 38 2.7.15 switchport vlan -------------------------------------------------------------------------------------------------------------------------- 39 2.7.16 show interface--------------------------------------------------------------------------------------------------------------------------- 39 2.7.17 show esw --------------------------------------------------------------------------------------------------------------------------------- 39 2.7.18 show interface switchport ------------------------------------------------------------------------------------------------------------ 40 2.7.19 show vlan--------------------------------------------------------------------------------------------------------------------------------- 40 2.7.20 qos ----------------------------------------------------------------------------------------------------------------------------------------- 40 2.7.21 qos default-cos-------------------------------------------------------------------------------------------------------------------------- 41 2.7.22 qos trust cos ----------------------------------------------------------------------------------------------------------------------------- 41 2.7.23 qos map cos-queue-------------------------------------------------------------------------------------------------------------------- 42 2.7.24 show qos --------------------------------------------------------------------------------------------------------------------------------- 43 2.7.25 mac-address-table aging-time------------------------------------------------------------------------------------------------------- 43 2.7.26 no mac-address-table aging-time -------------------------------------------------------------------------------------------------- 44 2.7.27 mac-address-table learning---------------------------------------------------------------------------------------------------------- 44 2.7.28 mac-address-table static HHHH.HHHH.HHHH vlan <2-4094> port <1-4> ---------------------------------------------- 45 2.7.29 mac-polling------------------------------------------------------------------------------------------------------------------------------- 46 2.7.30 clear mac-address-table -------------------------------------------------------------------------------------------------------------- 46 2.7.31 search mac-address ------------------------------------------------------------------------------------------------------------------- 47 2.7.32 show mac--------------------------------------------------------------------------------------------------------------------------------- 48

2.8 Relevant command of sub-card E-SUBM-2FV35/FV35--------------------------------------------------------48 2.8.1 bandwidth-config ------------------------------------------------------------------------------------------------------------------------- 48 2.8.2 interface ------------------------------------------------------------------------------------------------------------------------------------ 49 2.8.3 no loopback-------------------------------------------------------------------------------------------------------------------------------- 49 2.8.4 rxclk-phase -------------------------------------------------------------------------------------------------------------------------------- 50 2.8.5 show info ----------------------------------------------------------------------------------------------------------------------------------- 50 2.8.6 show interface ---------------------------------------------------------------------------------------------------------------------------- 51 2.8.7 show version ------------------------------------------------------------------------------------------------------------------------------ 51 2.8.8 v35-loopback ------------------------------------------------------------------------------------------------------------------------------ 51

2.9 Relevant commands of clock configuration----------------------------------------------------------------------52 2.9.1 device clock local ------------------------------------------------------------------------------------------------------------------------ 52 2.9.2 device clock sdh-port-------------------------------------------------------------------------------------------------------------------- 53 2.9.3 device clock e1 --------------------------------------------------------------------------------------------------------------------------- 53 2.9.4 device clock clear local ----------------------------------------------------------------------------------------------------------------- 54 2.9.5 device clock clear sdh-port ------------------------------------------------------------------------------------------------------------ 55 2.9.6 device clock clear e1 -------------------------------------------------------------------------------------------------------------------- 55 2.9.7 device clock force-switch local-------------------------------------------------------------------------------------------------------- 56 2.9.8 device clock force-switch sdh-port--------------------------------------------------------------------------------------------------- 56 2.9.9 device clock force-switch e1 ---------------------------------------------------------------------------------------------------------- 57 2.9.10 device clock lockout local ------------------------------------------------------------------------------------------------------------ 57 2.9.11 device clock lockout sdh-port -------------------------------------------------------------------------------------------------------- 58 2.9.12 device clock lockout e1 --------------------------------------------------------------------------------------------------------------- 58 2.9.13 device clock manual-switch local--------------------------------------------------------------------------------------------------- 59 2.9.14 device clock manual-switch sdh-port ---------------------------------------------------------------------------------------------- 59 2.9.15 device clock manual-switch e1------------------------------------------------------------------------------------------------------ 60 2.9.16 device clock pll -------------------------------------------------------------------------------------------------------------------------- 60 2.9.17 device clock reset local --------------------------------------------------------------------------------------------------------------- 61 2.9.18 device clock reset sdh-port ---------------------------------------------------------------------------------------------------------- 61 2.9.19 device clock reset e1 ------------------------------------------------------------------------------------------------------------------ 62 2.9.20 device clock wait-to-restore-time --------------------------------------------------------------------------------------------------- 62 2.9.21 device clock ssm ----------------------------------------------------------------------------------------------------------------------- 63 2.9.22 device clock local id-------------------------------------------------------------------------------------------------------------------- 64 2.9.23 device clock sdh-port id--------------------------------------------------------------------------------------------------------------- 64

2.9.24 device clock e1 id ---------------------------------------------------------------------------------------------------------------------- 65 2.9.25 show device clock ---------------------------------------------------------------------------------------------------------------------- 65

2.10 system configuration command ------------------------------------------------------------------------------------66 2.10.1 dcc select--------------------------------------------------------------------------------------------------------------------------------- 66 2.10.2 e1-retiming-src -------------------------------------------------------------------------------------------------------------------------- 66 2.10.3 e1 <1-4> retiming----------------------------------------------------------------------------------------------------------------------- 67

Chapter 3 Reference Materials ---------------------------------------------------------------------68 Appendix A Acronyms ------------------------------------------------------------------------------------72 Acronyms list 1----------------------------------------------------------------------------------------------72 Acronyms list 2----------------------------------------------------------------------------------------------73

Release Notes

Date of Release Manual Version Revisions

20080910 200711 First time release.

20090115 200811 Some modifications on clock commands.

Preface

About This Manual This manual introduces primary functions of the configuration management software for OPCOM3105 series products.

Who Should Read This Manual This manual is a valuable reference for sales and marketing staff, after service staff and telecommunication network designers. For those who want to have an overview of the features, applications, structure and specifications of OPCOM3105 device, this is also a recommended document.

Relevant Manuals

《OPCOM3105 User Manual》

《OPCOM3105 Configuration Guide》

《OPCOM3105 EMS User Manual》

Organization This manual is an introduction of the main functions of OPCOM3105. To have a quick grasp of the using of OPCOM3105, please read this manual carefully. The manual is composed of the following chapters

Chapter 1 How to Use the Command Line

This chapter briefly introduces how to use the command line access and configure OPCOM3105.

Chapter 2 Definitions of Command Line

This chapter generally introduces the configuration commands supported by software of OPCOM3105 device.

Chapter 3 Reference Materials

Appendix A Acronyms

Compliance The RC series products developed by Raisecom are strictly complied with the following standards as well as ITU-T, IEEE, IETF and related standards from other international telecommunication standard organizations:

YD/T900-1997 SDH Equipment Technical Requirements - Clock

YD/T973-1998 SDH 155Mb/s and 622Mb/s Technical conditions of optical transmitter module and receiver module

YD/T1017-1999 Network node interface for the Synchronous Digital Hierarchy (SDH)

YD/T1022-1999 Requirement of synchronous digital hierarchy (SDH) equipment function

YD/T1078-2000 SDH Transmission Network Technique Requirements-Interworking of Network Protection Architectures

YD/T1111.1-2001 Technical Requirements of SDH Optical Transmitter/Optical Receiver Modules——2.488320 Gb/s Optical Receiver Modules

YD/T1111.2- 2001 Technical Requirements of SHD Optical Transmitter/Optical Receiver Modules——2.488320 Gb/s Optical Transmitter Modules

YD/T1179- 2002 Technical Specification of Ethernet over SDH

G.703 Physical/electrical characteristics of hierarchical digital interfaces

G.704 Synchronous frame structures used at 1544, 6312, 2048, 8448 and 44 736 kbit/s hierarchical levels

G.707 Network node interface for the synchronous digital hierarchy (SDH)

G.774 Synchronous digital hierarchy (SDH) - Management information model for the network element view

G.781 Synchronization layer functions

G.783 Characteristics of synchronous digital hierarchy (SDH) equipment functional blocks

G.784 Synchronous digital hierarchy (SDH) management

G.803 Architecture of transport networks based on the synchronous digital hierarchy (SDH)

G.813 Timing characteristics of SDH equipment slave clocks (SEC)

G.823 The control of jitter and wander within digital networks which are based on the 2048 kbit/s hierarchy

G.825 The control of jitter and wander within digital networks which are based on the synchronous digital hierarchy (SDH)

G.826 End-to-end error performance parameters and objectives for international, constant bit-rate digital paths and connections

G.828 Error performance parameters and objectives for international, constant bit-rate synchronous digital paths

G.829 Error performance events for SDH multiplex and regenerator sections

G.831 Management capabilities of transport networks based on the synchronous digital hierarchy (SDH)

G.841 Types and characteristics of SDH network protection architectures

G.842 Interworking of SDH network protection architectures

G.957 Optical interfaces for equipments and systems relating to the synchronous digital hierarchy

G.691 Optical interfaces for single channel STM-64 and other SDH systems with optical amplifiers

G.664 Optical safety procedures and requirements for optical transport systems

I.731 ATM Types and general characteristics of ATM equipment

I.732 ATM Functional characteristics of ATM equipment

IEEE 802.1Q Virtual Local Area Networks (LANs)

IEEE 802.1p Traffic Class Expediting and Dynamic Multicast Filtering

IEEE 802.3 CSMA/CD Access Method and Physical Layer Instruction

www.raisecom.com User Manual

1

Chapter 1 How to Use the Command Line

1.1 Software and hardware environment

Operation environment of hardware: OPCOM3105 platform

PC serial interface

Operation environment of software: WIN98/WIN2000/WINDOWS XP

1.2 Command line modes

Mode Mode description Access Prompts

User EXEC

Configuring the basic information and show the parameters etc. at terminal

device.

Login the device and input the user name and password. OPCOM3105>

Privileged EXEC

Configuring the basic information such as system

time and show the parameters but not the running

information of OPCOM3105.

Use enable command under user EXEC mode. OPCOM3105#

Global configuration

mode

Configuring running parametersof OPCOM3105.

Use config command under Privileged EXEC mode. OPCOM3105(config )#

Interface configuration

mode

Configuring parameters of Ethernet network

management interface, SDH interface, ETH interfaces.

Use interface [eth/eos/stm-1/e1/switch/snmp/dcc]

command under Global configuration mode.

OPCOM3105 (config-xxx/n)#

xxx: interface number.

Table 1-1 Command Line Modes

1.3 Command line format annotation

1. All optional parameters should be bracketed into a “[]”, regardless of how many parameters there are. Parameters should be separated by “|”.

2. In the case of any choices of required parameters or command keywords, all parameters and command keywords should be bracketed into a “()”. Parameters and command keywords should be separated by “|”.


2

Chapter 2 Definitions of Command Line

2.1 Relevant commands of SDH crossconnect timeslot

2.1.1 sdh crossconnect (vc12|vc3) [Function]

This command is used to configure crossconnect for device, users can delete crossconnect by command no.

[Command Format]

sdh crossconnect (vc12|vc3) source-port <1-2> timeslot {1-63} destination-port <1-2> timeslot {1-63}

no sdh crossconnect (vc12|vc3) source-port <1-2> timeslot {1-63} destination-port <1-2> timeslot {1-63}

[Parameter]

(vc12|vc3) : select crossconnect type;

vc12: crossconnect type is VC12;


<1-2>: sdh port index.

<1-63> : sdh timeslot.

TSSTRING : timeslot string to configure, use “,” to separate single timeslots; use “-” to connect range, for example 1, 3-5 means timeslot 1, and timeslot 3, 4, 5.

[Command mode]

Global configuration mode

[Application Example]

Create vc12 crossconnect from sdh source-port 1 timeslot 1 to sdh destination-port 2 timeslot 5:

OPCOM3105(config)# sdh crossconnet vc12 source-port 1 timeslot 1 destination-port 2 timeslot 5

[Relevant Commands]

Command Description

show sdh crossconnect Show sdh port crossconnect configuration information.

2.1.2 sdh crossconnect (vc12|vc3) TSSTRING [Function]

This command is used to configure crossconnect for timeslots corresponding to ports of the device.


3

[Command Format]

sdh crossconnect (vc12|vc3) TSSTRING

[Parameter]

(vc12|vc3) : select crossconnect type;


vc3: means crossconnect type is VC3;

TSSTRING : timeslot string to configure, use “,” to separate single timeslot; use “-” to connect range for example 1, 3-5 means timeslot 1, and timeslot 3, 4, 5.

[Command mode]



Create vc12 crossconnect from sdh port 1 timeslot 1-8 to sdh port 2 timeslot 1-8:

OPCOM3105(config)# sdh crossconnet vc12 1-8

[Relevant Commands]

Command Description

show sdh crossconnect Show sdh port crossconnect configuration information.

2.1.3 show sdh crossconnect [Function]

This command is used to show the already configured sdh crossconnect.

[Command Format]

show sdh crossconnect

[Command mode]

Privileged EXEC mode, Global configuration mode


Show the already configured sdh crossconnect:

OPCOM3105# show sdh crossconnect

[Relevant Commands]

Command Description

sdh crossconnect Configure sdh port timeslot crossconnect.

2.1.4 timeslot add sdh [Function]

This command is used to add one mapping between E1/EOS interface and sdh timeslot, it can


4

assign backboard timeslot.

[Command Format]

timeslot add sdh <1-2> (vc12|vc3) SDHTSSTRING [SVCTSSTRING]

[Parameter]


(vc12|vc3) : timeslot type level selection ;

vc12: timeslot type is VC12;

vc3: means timeslot is VC3;

SDHTSSTRING: SDH timeslot string to configure.

SVCTSSTRING: backboard timeslot string to configure.

[Command mode]

EOS, E1 interface configuration mode

[Instructions]

System assigns backboard timeslot automatically if not input SVCTSSTRING parameters.


Add timeslot 1 at E1 port 1 meanwhile create an interior crossconnect to SDH port 1 timeslot 1:

OPCOM3105 (config-e1/1)# timeslot add sdh 1 vc12 1 1

[Relevant Commands]

Command Description

show timeslot Show timeslot assigning configuration information.

2.1.5 timeslot delete sdh [Function]

This command is used to delete one mapping between E1/EOS interface and sdh timeslot.

[Command Format]

timeslot delelte sdh <1-2> (vc12|vc3) SDHTSSTRING

[Parameter]


(vc12|vc3) : timeslot type level selection ;

vc12: timeslot type is VC12;

vc3: means timeslot is VC3;

SDHTSSTRING: SDH timeslot string to configure.

[Command mode]



5


Delete timeslot 1 under E1 port 1:

OPCOM3105 (config-e1/1)# timeslot del sdh 1 vc12 1

[Relevant Commands]

Command Description

show timeslot Show timeslot assigning configuration information.

2.1.6 show timeslot [Function]

This command is used to show relevant information of already assigned timeslot.

[Command Format]

show timeslot

[Command mode]

Privileged EXEC mode, Global configuraiton mode


Show timeslot assigning information:

OPCOM3105 # show timeslot

[Relevant Commands]

Commands Description

timeslot add sdh Configuration of timeslot assignment.

timeslot delete sdh Delete timeslot assignment.

2.1.7 show interface timeslot [Function]

This command is used to show relevant information of assigned timeslot under EOS, E1 interface.

[Command Format]

show interface timeslot

[Command mode]



Show timeslot assigning configuration at EOS interface 2:

OPCOM3105(config-eos/0/2)# show interace timeslot

[Relevant Commands]


6


timeslot add sdh Configuration of timeslot assignment.

timeslot delete sdh Delete timeslot assignment.

2.2 Relevant commands of protection

2.2.1 protect-switch enable [Function]

This command is used to configure protect-switch type and enable the function.

[Command Format]

protect-switch enable [type (path|ms)]

[Parameter]

path|ms: type of protect-switch;

path: protect path ;

ms: protect multiplex section.

[Default]

Protect-switch function enable and adopts path protection by default.

[Command mode]



Configure protect-switch enable in type of path:

OPCOM3105# config

OPCOM3105(config)# protect-switch enable type path

Create successfully

[Relevant Commands]


show aps Show protect-switch configuration information.

2.2.2 protect-switch disable [Function]

This command is used to disable protect-switch.

[Command Format]

protect-switch disable

[Command mode]



7


Configure protect-switch disable:

OPCOM3105# config

OPCOM3105(config)# protect-switch disable

Set successfully

[Relevant Commands]



2.2.3 aps-restore-time [Function]

This command is used to configure Auto-protect-switch restore time.

[Command Format]

aps-restore-time <0-12>

[Parameter]

<0-12>: aps restore time, unit: minute

[Default]

12 minutes

[Command mode]


[Instructions]

0 means no need to wait for aps restore, the link switch to master link directly after it recovers.


Configure Auto-protect-switch restore time to be 3:

OPCOM3105# config

OPCOM3105(config)# aps-restore-time 3

Set successfully

[Relevant Commands]



2.2.4 aps-mode [Function]

This command is used to configure whether enable aps-mode.


8

[Command Format]

aps-mode (revertive|nonrevertive)

[Parameter]

(revertive|nonrevertive): whether enable auto-revert

[Default]

revert

[Command mode]



Configure aps-mode to be nonrevertive:

OPCOM3105# config

OPCOM3105(config)# aps-mode nonrevertive

Set successfully

[Relevant Commands]



2.2.5 force-switch [Function]

This command is used to force-switch working path for assigned timeslot.

[Command Format]

force-switch {work-line|protection-line|clear} [{vc3|vc12} TSSTRING]

[Parameter]

{work-line|protection-line|clear}: select parameter to operate

work-line: force switch to work line

protection-line: force switch to protection line

clear: clear force siwtch

TSSTRING: timeslot string to operate; use “,” to separate single timeslot; use “-” to connect timeslot range. For example: 1, 3-5 means timeslot 1 and timeslot 3, 4, 5.

[Command mode]


[Instructions]

Force-switch function is available only after configured relevant timeslot and protection enable.



9

OPCOM3105# config

OPCOM3105(config)# force-switch work-line vc12 1,3-6

Set successfully

[Relevant Commands]



2.2.6 manual-switch [Function]

This command is used to force-switch working path for assigned timeslot.

[Command Format]

manual-switch {work-line|protection-line|clear} [{vc3|vc12} TSSTRING]

[Parameter]

{work-line|protection-line|clear}: select parameter to operate

work-line: force switch to work line

protection-line: force switch to protection line

clear: clear force siwtch

TSSTRING: timeslot string to operate; use “,” to separate single timeslot; use “-” to connect timeslot range. For example: 1, 3-5 means timeslot 1 and timeslot 3, 4, 5.

[Command mode]


[Instructions]

Manual-switch can be operated only in condition that there is protection pair and the protection pair is valid.


OPCOM3105# config

OPCOM3105(config)# manual-switch work-line vc12 1,3-6

Set successfully

[Relevant Commands]



2.2.7 show aps [Function]


10

This command is used to show protect-switch configuration information.

[Command Format]

show aps

[Command mode]



OPCOM3105# config

OPCOM3105(config)# show aps

2.3 Commands of SDH interface

2.3.1 interface stm1-opt [Function]

This command is used to enter interface configuration mode.

[Command Format]

interface stm1-opt <1-2>

[Parameter]

<1-2>: STM1 optical interface number.

[Command mode]

Global configuration mode, STM1 interface configuration mode


Enter STM1 optical port 1:

OPCOM3105(config)# interface stm1-opt 1

[Relevant Commands]


show interface Show interface information.

2.3.2 sdh description [Function]

This command is used to configure sdh interface description.

[Command Format]

sdh description STRING

[Parameter]

STRING: sdh interface description information

[Command mode]


11

Interface configuration mode

[Instructions]

Use character “^” instead of character “space” in the interface description.


Configure optical port description information to be raisecom-inter-01:

OPCOM3105(config-stm1-opt/0/1)# sdh description raisecom-inter-01

[Relevant Commands]



2.3.3 loopback [Function]

This command is used to configure STM-1 port loopback, no command can used to cancel loopback.

[Command Format]

loopback external

no loopback

[Parameter]

external: loopback type. External means remote port external loopback.

[Default]

No loopback

[Command mode]



Configure local optical port external loopback:

OPCOM3105(config-stm1-opt/0/1)# loopback external

[Relevant Commands]



2.3.4 als [Function]

This command is used to configure STM-1 port als function.

[Command Format]


12

als （enable|disable）

[Parameter]

(enable|disable): als function enable/disable.

[Default]

disable

[Command mode]



Enable optical interface als function:

OPCOM3105(config-stm1-opt/0/1)# als enable

[Relevant Commands]



2.3.5 clear-statistic [Function]

This command is used to reset all current internal statistics information of sdh.

[Command mode]



Reset all current internal statistics information of sdh:

OPCOM3105(config-stm1-opt/0/1)# reset-statistic

2.3.6 sdh aupje-threshold [Function]

This command is used to configure SDH high order path AU pointer adjust threshold.

[Command Format]

sdh aupje-threshold (positive|negative) <1-65535>

[Parameter]

(positive|negative): select the pointer adjust direction to set, positive means adjust pointer at positive direction; negative means adjust pointer at negative direction.

<1-65535>: threshold value.

[Default]

Threshold is 900 by default.


13

[Command mode]



Set positive pointer adjust threshold value to 300:

OPCOM3105(config-stm1-opt/0/1)# sdh aupje-threshold positive 300

[Relevant Commands]



2.3.7 sdh es-threshold [Function]

This command is used to configure SDH error second threshold.

[Command Format]

sdh es-threshold (regenerator-section|multiplex-section|higher-path|lower-path) <1-900>

[Parameter]

(regenerator-section|multiplex-section|higher-path|lower-path): select the section to set;

regenerator-section: regenerator section;

multiplex-section: multiplex section;

higher-path: higher order path;

lower-path: lower order path;

<1-900>: error second threshold value.

[Default]

All error second threshold values are 900.

[Command mode]



Set multiplex section error second threshold value to 300:

OPCOM3105(config-stm1-opt/0/1)# sdh es-threshold multiplex-section 300

[Relevant Commands]



2.3.8 sdh msais-insert [Function]


14

This command is used to configure enable/disable MS-AIS insert function.

[Command Format]

sdh msais-insert (rstim|msexc) (enable|disable)

[Parameter]

(rstim|msexc): conditions for insert MS-AIS function;

rstim: insert when regenerator section TIM alarm happens;

msexc: insert when multiplex section EXC alarm happens;

(enable|disable): enable: insert enable;

disable: insert disable.

[Default]

Disable : disable MS-AIS insert function when regenerator section TIM and multiplex section EXC alarm happen.

[Command mode]



Insert MS-AIS when regenerator section TIM alarm happens:

OPCOM3105(config-stm1-opt/0/1)# sdh msais-insert rstim enable

[Relevant Commands]



2.3.9 sdh tuais-insert [Function]

This command is used to configure enable/disable TU-AIS insert function.

[Command Format]

sdh tuais-insert (hpexc|hpplm|hptim) (enable|disable)

[Parameter]

(hpexc|hpplm|hptim): conditions for insert TU-AIS function;

hpexc: insert when higher order path EXC alarm happens;

hpplm: insert when higher order path PLM alarm happens;

hptim: insert when higher order path TIM alarm happens;

(enable|disable): enable: insert enable;

disable: insert disable.

[Default]


15

Disable : disable TU-AIS insert function when higher order path EXC, higher order path PLM and higher order path TIM alarm happen.

[Command mode]



Insert TU-AIS when higher order path PLM alarm happens at STM optical port 1:

OPCOM3105(config-stm1-opt/0/1)# sdh tuais-insert hpplm enable

[Relevant Commands]


show interface Show SDH interface information.

2.3.10 sdh overhead c2 [Function]

This command is used to configure higher order path C2 byte to send and C2 byte to receive.

[Command Format]

sdh overhead c2 [vc4 <1-1>] [vc3 <1-3>] [transmit BYTE] [expected BYTE]

[Parameter]

vc4: means vc4 index has been configured, only 1 vc4 at present;

vc3: select vc3 index for configuring, valued from 1-3 for configuring vc3 C2 byte, this parameter is omitted when configure vc4 C2 byte;

BYTE: C2 byte information expects to receive, hexadecimal digitals;

BYTE: C2 byte information to transmit, hexadecimal number.

[Default]

C2 byte information to transmit and expect to receive are both 0x02.

[Command mode]

STM1 interface configuration mode


Configure C2 byte information to transmit and expect to receive to be both 0x03:

OPCOM3105(config-stm1-opt/0/1)# sdh overhead c2 expected 0x03 transmit 0x03

[Relevant Commands]




16

2.3.11 sdh overhead j0 [Function]

This command is used to configure regenerator section trace byte J0 string expects to receive and to transmit.

[Command Format]

sdh overhead j0 [expected EXPMSG] [transmit XMITMSG]

[Parameter]

EXPMSG: j0 string expects to receive;

XMITMSG: j0 string expects to transmit.

[Default]

J0 string expects to receive and to transmit are both Raisecom-Opcom.

[Command mode]


[Instructions]

The character number must not more than 16 in factual command operation, use “^” to instead of “space” character.


Configure j0 string to transmit and expects to receive to be both OPCOM3105:

OPCOM3105(config-stm1-opt/0/1)# sdh overhead j0 expected OPCOM3105 transmit

OPCOM3105

[Relevant Commands]



2.3.12 sdh overhead j0-mode [Function]

This command is used to configure regenerator section trace byte J0 string expects to receive and to transmit.

[Command Format]

sdh overhead j0-mode (one-byte | sixteen-byte)

[Parameter]

one-byte: use j0 one byte mode;

sixteen-byte: use j0 16 byte mode.

[Default]

J0 16 byte mode.


17

[Command mode]



Configure j0 16 byte mode:

OPCOM3105(config-stm1-opt/0/1)# sdh overhead j0-mode sixteen-byte

[Relevant Commands]



2.3.13 sdh overhead j1 [Function]

This command is used to configure HP trace byte J1 string expects to receive and to transmit.

[Command Format]

sdh overhead j1 [vc4 <1-1>] [vc3 <1-3>] [expected EXPMSG] [transmit XMITMSG]

[Parameter]

vc4: means vc4 index has been configured, only 1 vc4 at present;

vc3: means select vc3 index for configuring, valued from 1-3 for configuring vc3 J1 byte, this parameter is omitted when configure vc4 J1 byte;

EXPMSG: j1 string expects to receive;

XMITMSG: j1 string to transmit.

[Default]

J1 string expects to receive and transmit are both Raisecom-Opcom.

[Command mode]


[Instructions]

The character number must not more than 16 in factual command operation, use “^” to instead of “space” character.


Configure j1 string to transmit and expects to receive to be both OPCOM3105:

OPCOM3105(config-stm1-opt/0/1)# sdh overhead j1 expected OPCOM3105 transmit

OPCOM3105

[Relevant Commands]




18

2.3.14 sdh overhead j1-mode [Function]

This command is used to configure HP trace byte J1 string expects to receive and transmit.

[Command Format]

sdh overhead j0-mode (sixteen-byte | sixtyfour-byte)

[Parameter]

sixtyfour-byte: use j1 64 byte mode;

sixteen-byte: use j1 16 byte mode.

[Default]

J1 16 byte mode.

[Command mode]



Configure j1 16 byte mode:

OPCOM3105(config-stm1-opt/0/1)# sdh overhead j1-mode sixteen-byte

[Relevant Commands]



2.3.15 sdh overhead k1 [Function]

This command is used to configure k1 byte to transmit.

[Command Format]

sdh overhead k1 BYTE

[Parameter]

BYTE: k1 byte to transmit.

[Default]

K1 byte to transmit is 0x0.

[Command mode]



Configure transmit k1 byte 0x0:

OPCOM3105(config-stm1-opt/1)# sdh overhead k1 0x0

[Relevant Commands]


19




This command is used to configure k2 byte to transmit.

[Command Format]

sdh overhead k2 BYTE

[Parameter]

BYTE: k2 byte to transmit.

[Default]

K2 byte to transmit is 0x0.

[Command mode]



Configure transmit k2 byte 0x0:

OPCOM3105(config-stm1-opt/1)# sdh overhead k2 0x0

[Relevant Commands]



2.3.17 sdh overhead v5 [Function]

This command is used to configure v5 byte expects to receive and to transmit.

[Command Format]

sdh overhead v5 [vc4 <1-1>] [vc12 <1-63>] [expected BYTE] [transmit BYTE]

[Parameter]

vc4: vc4 index, only 1 vc4 at present;

vc12: vc12 timeslot (TS) index, <1-63>;

BYTE: v5 byte information expects to receive;

BYTE: v5 byte information to transmit.

[Default]

Vc12 v5 is 0x2 by default.

[Command mode]


20



Configure VC12-1 transmit and expect v5 byte to be both 0x5:

OPCOM3105(config-stm1-opt/0/1)# sdh overhead v5 vc12 1 expected 0x5 transmit 0x5

[Relevant Commands]




This command is used to configure k4 byte expects to receive and to transmit.

[Command Format]

sdh overhead k4 [vc4 <1-1>] [vc12 <1-63>] [expected BYTE] [transmit BYTE]

[Parameter]

vc4: vc4 index, only 1 vc4 at present;

vc12: vc12 timeslot (TS) index, <1-63>;

BYTE: k4 byte information expects to receive;

BYTE: k4 byte information to transmit.

[Default]

Vc12 k4 is 0xb by default.

[Command mode]



Configure VC12-1 tranmist and expect k4 byte to be both 0xd:

OPCOM3105(config-stm1-opt/0/1)# sdh overhead k4 vc12 1 expected 0xd transmit 0xd

[Relevant Commands]



2.3.19 sdh sd-threshold [Function]

This command is used to configure SDH signal degrade threshold.

[Command Format]

sdh sd-threshold (regenerator-section|multiplex-section|higher-path|lower-path) <6-8>


21

[Parameter]

(regenerator-section|multiplex-section|higher-path|lower-path): select section to set;

regenerator-section: regenerator-section;

multiplex-section: multiplex-section ;

higher-part: higher-path ;

lower-path: lower-path ;

<6-8>: signal degrade threshold; 6 means threshold is 10-6; 7 means threshold is 10-7; 8 means threshold is 10-8.

[Default]

Threshold is 6 for all types of signal degrade.

[Command mode]



Configure multiplex section signal degrade threshold to be 10-6:

OPCOM3105(config-stm1-opt/0/1)# sdh sd-threshold multiplex-section 6

[Relevant Commands]



2.3.20 show sdh-alarm [Function]

This command is used to show all SDH alarm of port at present.

[Command Format]

show sdh-alarm

[Command mode]



Show STM1 port 1 all SDH alarm at present:

OPCOM3105(config-stm1-opt/0/1)#show sdh-alarm

2.3.21 show interface timeslot-occupy [Function]

This command is used to show SDH timeslot occupation status at present.

[Command Format]


22

show interface timeslot-occupy

[Command mode]


[Command Execute Echo]

sdh-port timeslot state

-----------------------------------------

1 vc3 1 NoOccupied

1 vc3 2 NoOccupied

1 vc3 3 NoOccupied

1 vc12 1 Occupied by svc








1 vc12 9 NoOccupied

1 vc12 10 Occupied by xc

1 vc12 11 NoOccupied








Show timeslot occupation status at present port:

OPCOM3105(config-stm1-opt/0/1)# show interface timeslot-occupy

2.3.22 show interface stm1 [Function]

This command is used to show sdh interface configuration information.

[Command Format]

show interface stm1 <1-2>

[Parameter]


23

<1-2>: sdh interface number

[Command mode]

Global configuration mode, Interface configuration mode


Show sdh interface 1 information:

OPCOM3105(config-stm1-opt/0/1)# show interface sdh 1

[Relevant Commands]


show interface Show interface configuration information.

show interface stm1 Show interface configuration information.

2.3.23 show interface [Function]

This command is used to show configuration of current STM port.

[Command Format]

show interface

[Command mode]



Show STM optical port 2 configuration information:

OPCOM3105(config-stm1-opt/0/2)# show interface

2.4 Commands of E1 interface

2.4.1 interface e1 [Function]

This command is used to enter E1 interface.

[Command Format]

interface e1 <1-8>

[Parameter]

<1-8>: E1 interface number

[Command mode]




24

Enter E1 interface 1 :

OPCOM3105 (config)# interface e1 1

[Relevant Commands]



2.4.2 e1-loopback [Function]

This command is used to configure E1 loopback and cancel E1 loopback.

[Command Format]

e1-loopback (internal | external)

no e1-loopback

[Parameter]

(internal|external): internal: local interface internal loopback;

external: remote interface external loopback.

[Default]

No E1 loopback

[Command mode]

E1 interface configuration mode


Connect E1 remote interface loopback:

OPCOM3105 (config-e1/0/1)# e1-loopback external

Cancel E1 remote interface loopback:

OPCOM3105 (config-e1/0/1)# no e1-loopback

[Relevant Commands]




This command is used to show E1 interface configuration information.

[Command Format]

show interface


25

[Command mode]

E1 interface configuration mode


Show E1 interface information:

OPCOM3105 (config-e1/0/1)# show interface

2.5 Commands of ETH interface

2.5.1 automdi [Function]

This command is used to configure Auto-MDI function; no command can be used to disable the function.

[Command Format]

[no] automdi

[Default]

Auto-MDI function enable

[Command mode]

ETH interface mode


Enable ETH interface Auto-MDI function:

OPCOM3105 (config-eth/0/1)# automdi

[Relevant Commands]



2.5.2 autonegotiate [Function]

This command is used to configure Auto-Negotiation function; no command can be used to disable the function.

[Command Format]

[no] autonegotiate

[Default]

Auto-Negotiation function enable

[Command mode]

ETH interface mode


26


Disable ETH interface Auto-Negotiation function:

OPCOM3105 (config-eth/0/1)# no autonegotiate

[Relevant Commands]



2.5.3 clear statistic [Function]

This command is used to clear statistic information.

[Command Format]

clear statistic

[Command mode]

ETH interface mode, Switch interface mode


Clear ETH flow statistic information:

OPCOM3105 (config-eth/0/1)# clear statistic

[Relevant Commands]



2.5.4 speed (10|100|1000) duplex (full-duplex|half-duplex) [Function]

This command is used to configure duplex rate of ETH interface.

[Command Format]

speed (10|100|1000) duplex (full-duplex|half-duplex)

[Parameter]

(10|100|1000): interface rate, unit: M;

(full-duplex|half-duplex): duplex status ;

full-duplex: full-duplex;

half-duplex: half-duplex.

[Command mode]

ETH interface mode

[Instructions]


27

This configuration is valid only when interface Auto-Negotiation disable.


Configure ETH interface to be 10M half-duplex:

OPCOM3105 (config-eth/0/1)# speed 10 duplex half-duplex

[Relevant Commands]



2.5.5 interface eth [Function]

This command is used to enter ETH interface.

[Command Format]

interface eth <1-4>

[Parameter]

<1-4>: ETH interface number

[Command mode]

Global configuration mode, ETH interface mode


Enter ETH interface 1:

OPCOM3105 (config-eth/0/1)# interface eth 1

[Relevant Commands]




This command is used to show interface configuration information.

[Command Format]

show interface

[Command mode]

ETH interface mode


Show ETH interface configuration information:


28

OPCOM3105 (config-eth/0/1)# show interface

[Relevant Commands]



2.5.7 shutdown [Function]

This command is used to shutdown ETH interface, no command can be used to open ETH interface.

[Command Format]

shutdown

no shutdown

[Default]

ETH interface open

[Command mode]

ETH interface configuration mode


Configure ETH interface shutdown:

OPCOM3105 (config-eth/0/1)# shutdown

[Relevant Commands]



2.6 Commands of EOS interface

2.6.1 interface eos [Function]

This command is used to enter EOS interface.

[Command Format]

interface eos <1-2>

[Parameter]

<1-2>: EOS interface index

[Command mode]

Global configuration mode, EOS interface configuration mode



29

Enter the first EOS interface:

OPCOM3105 (config)#interface eos 1

[Relevant Commands]



2.6.2 clear statistic [Function]

This command is used to clear flow statistic information.

[Command Format]

clear statistic

[Command mode]

EOS interface mode


Clear EOS flow statistic information:

OPCOM3105 (config-eos/0/1)# clear statistic

[Relevant Commands]


show interface eos Show interface configuration information.


2.6.3 encapsulation [Function]

This command is used to configure Ethernet encapsulation mode.

[Command Format]

encapsulation （gfp|laps）

[Parameter]

gfp: configure VCG encapsulation mode to be gfp;

laps: configure VCG encapsulation mode to be laps.

[Command mode]

EOS interface configuration mode


Configure VCG encapsulatin mode to be gfp:


30

OPCOM3105 (config-eos/0/1)# encapsulation gfp

[Relevant Commands]




2.6.4 gfp-fcs [Function]

This command is used to configure whether enable fcs under gfp encapsulation mode.

[Command Format]

gfp-fcs（enable| disable）

[Parameter]

enable: fcs enable;

disable: fcs disable.

[Command mode]



Configure fcs enable:

OPCOM3105 (config-eos/0/1)#gfp-fcs enable

[Relevant Commands]




2.6.5 lcas [Function]

This command is used to configure whether enable lcas function.

[Command Format]

lcas（on| off）

[Parameter]

on: lcas on;

off: lcas off.

[Command mode]


31



Configure lcas on:

OPCOM3105 (config-eos/0/1)# lcas on

[Relevant Commands]




2.6.6 show interface eos [Function]

This command is used to show EOS interface configuration information.

[Command Format]

show interface eos <1-2>

[Parameter]

<1-2>: eos interface number

[Command mode]



Show EOS interface 1 information:

OPCOM3105 (config-eos/0/1)# show interface eos 1

[Relevant Commands]





[Command Format]

show interface

[Command mode]




32

Show ETH interface information:

OPCOM3105 (config-eos/0/1)# show interface

[Relevant Commands]


show interface eos Show EOS interface configuration information.

2.7 Commands of ETH switchport

2.7.1 rate-limit [Function]

This command is used to limit port rate, no command can be used to cancel this command.

[Command Format]

[no] rate-limit <1-1048576>

[Parameter]

<1-1048576>: limit the rate, unit: Kbps

[Command mode]

Switchport mode

[Instructions]

Rate limit provides limit for bi-direction rate, since hardware rate limit range is integral times of granularity, the actual rate limit may different from configured rate.

[Command Execute Echo]

If the limit rate higher than 100M or lower than the rate limit granularity, error information will be displayed.


Configure switchport 1 rate to be 2 M:

OPCOM3105 (config-eswif/0/1)# rate-limit 2048

Cancel export rate limit:

OPCOM3105 (config-eswif/0/1)# no rate-limit

[Relevant Commands]


show rate-limit Show rate limit configuration information.

2.7.2 show rate-limit [Function]


33

This command is used to show rate limit configuration information.

[Command Format]

show rate-limit

[Command mode]

Global configuration mode, switchport mode


Show rate limit configuration information:

OPCOM3105(config-esw/1)# show rate-limit

[Relevant Commands]


[no] rate-limit Rate limit configuration.

rate-limit step Rate limit granularity configuration.

2.7.3 strom-control-global [Function]

This command is used to configure storm control function.

[Command Format]

storm-control-global ( broadcast | multicast | dlf | disable | all )

[Parameter]

broadcast: broadcast the message;

multicast: multicast and broadcast message;

dlf: dlf message;

all: all messages;

disable: storm control disable.

[Command mode]



Configure multicast storm control enable:

OPCOM3105 (config)# storm-control-global multicast enable

[Relevant Commands]


show strom-control-global Show storm control configuration information.


34

2.7.4 storm-control-global rate [Function]

This command is used to configure switchport storm control rate.

[Command Format]

storm-control-global rate <62-262144>

[Parameter]

<62-262144>: storm control rate, unit: kbit/s.

[Parameter]

62 kbit/s

[Command mode]



Configure switchport storm control rate to be 64 kbit/s:

OPCOM3105 (config)# storm-control-global rate 64

[Relevant Commands]


show strom-control-global Show storm control configuration information.

2.7.5 show strom-control-global [Function]

This command is used to show storm control configuration information.

[Command Format]

show storm-control-global

[Command mode]



Show storm control configuration information:

OPCOM3105 (config)# show storm-control-global

[Relevant Commands]


strom-control-global Configure storm control function.

2.7.6 vlan [Function]


35

This command is used to create vlan or enter static vlan mode, no command can be used to delete vlan.

[Command Format]

[no] vlan <2-4094>

[Parameter]

<2-4094>: vlan ID.

[Default]

Port 1 belongs to vlan 101 access interface;



Port 4 is internal aggregation interface, belongs to trank allow vlan 1, 101, 102, 103 port by default.

[Command mode]

Global configuration mode, switchport mode, vlan mode


Create vlan 15:

OPCOM3105 (config)# vlan 15

2.7.7 state [Function]

This command is used to configure vlan working status.

[Command Format]

state (active | suspend)

[Parameter]

active: vlan enable;

suspend: vlan disable.

[Command mode]

vlan mode


Enable vlan at this node:

OPCOM3105 (config-vlan/2)# state active

2.7.8 interface switchport [Function]


36

This command is used to enter switchport mode.

[Command Format]

interface switchport <1-4>

[Parameter]

<1-4>: switchport number

[Command mode]



Enter switchport 1:

OPCOM3105 (config)# interface switchport 1

2.7.9 switchport [Function]

This command is used to add assigned switchport to current vlan. The assigned port mode won’t be changed. It change the port direct to vlan id if current port is in access or tunnel mode; It is allowed to add vlan in the vlan list if the port is in hybrid mode; if the display assigned vlan list in trunk mode, add the vlan to the list.

No command can be used to delete assigned switchport. The assigned port mode won’t be changed. It change vlan id direct to global port id if current port is in access or tunnel mode; It is allowed to delete vlan from the vlan list if the port is in hybrid mode; if the display assigned vlan list in trunk mode, delete the vlan from the list.

[Command Format]

switchport GLOBALPORTIDLIST

no switchport GLOBALPORTIDLIST

[Parameter]

GLOBALPORTIDLIST: switchport ID number, range from 1-4, use “,” and “-” when input several ports id.

[Command mode]

vlan mode

[Instructions]

Configure switchport can also realize this function. Vlan configuration will be saved in form of switchport configuration.


Add switchport 5 to current vlan list:

OPCOM3105 (config-vlan/12)# switchport 5


37

2.7.10 switchport access vlan [Function]

This command is used to configure port mode to be access mode and assign vlan for the port.

[Command Format]

switchport access vlan <2-4094>

[Parameter]

<2-4094>: vlanID index.

[Command mode]

Switchport mode


Configure port to be access port of vlan 15:

OPCOM3105 (config-eswif/0/2)# switchport access vlan 15

2.7.11 switchport dot1q-tunnel vlan [Function]

This command is used to configure port mode to be tunnel mode and assign vlan for the port.

[Command Format]

switchport dot1q-tunnel vlan <2-4094>

[Parameter]

<2-4094>: vlanID index.

[Command mode]

Switchport mode


Configure port to be tunnel port of vlan 15:

OPCOM3105 (config-eswif/0/2)# switchport dot1q-tunnel vlan 15

2.7.12 switchport trunk allowed vlan list [Function]

This command is used to configure port mode to be trunk mode and assign vlan allowed by the port.

[Command Format]

switchport trunk allowed vlan list

[Parameter]

list: vlanID list.


38

[Command mode]

Switchport mode


Configure port to be trunk port permitting vlan 3, 4, 5:

OPCOM3105 (config-eswif/0/4)# switchport trunk vlan 3-5

2.7.13 switchport hybrid allowed vlan [Function]

This command is used to configure port mode to be hybrid mode and assign vlan allowed by the port.

[Command Format]

switchport hybrid allowed vlan list

[Parameter]

list: vlanID list, use “,” and “-” to separate several vlan.

[Command mode]

Switchport mode


Configure port to be hybrid port permitting vlan 3, 4, 5:

OPCOM3105 (config-eswif/0/2)# switchport hybrid allowed vlan 3-5

2.7.14 switchport mode [Function]

This command is used to configure port mode without change the port vlan id.

[Command Format]

switchport mode (access | dot1q-tunnel)

[Parameter]

access: access mode;

dotlq-tunnel: tunnel mode.

[Command mode]

Switchport mode


Configure port 2 to be access port:

OPCOM3105 (config-eswif/0/2)# switchport mode access


39

2.7.15 switchport vlan [Function]

This command is used to configure port vlan id without change port mode.

[Command Format]

switchport vlan <2-4094>

[Parameter]

<2-4094>: vlan id

[Command mode]

Switchport mode


Configure vlan id of port 2 to be 24:

OPCOM3105 (config-eswif/0/2)# switchport vlan 24



[Command Format]

show interface

[Command mode]

Ethernet interface mode, Switchport mode, E1 interface mode


Show configuration information of switchport 2:

OPCOM3105 (config-eswif/0/2)# show interface

2.7.17 show esw [Function]

This command is used to show basic information of Eth-switch interface.

[Command Format]

show esw

[Command mode]



Show basic information of Eth-switch interface:


40

OPCOM3105 (config)# show esw

2.7.18 show interface switchport [Function]

This command is used to show information of assigned switchport.

[Command Format]

show interface switchport <1-4>

[Parameter]

<1-4>: switchport index

[Command mode]



Show information of switchport 4:

OPCOM3105 (config-eswif/0/2)# show interface switchport 4

2.7.19 show vlan [Function]

This command is used to show vlan configuration information.

[Command Format]

show vlan [<2-4094>]

[Parameter]

<2-4094>: vlan id

[Command mode]

Privileged EXEC mode, Global configuration mode, Static vlan mode, Switchport mode

[Instructions]

Show all vlan information if no vlan ID was assigned.


Show information of vlan 15:

OPCOM3105 (config-eswif/2)# show vlan 15

2.7.20 qos [Function]

This command is used to configure qos function, no command can used to cancel qos. This function always aims at all ports.


41

[Command Format]

[no] qos

[Default]

No qos

[Command mode]


[Instructions]

Cancel QOS function means using port priority configuration, and all ports priorities are 0 (the highest).


Configure QOS function disable:

OPCOM3105 (config)# no qos

2.7.21 qos default-cos [Function]

This command is used to configure default cos value for current switchport.

[Command Format]

qos default-cos <0-7>

[Parameter]

<0-7>: cos value

[Default]

0

[Command mode]

Switchport mode


Configure cos value of switchport 1 to be 1:

OPCOM3105 (config-eswif/1)# qos default-cos 1

[Relevant Commands]


qos Qos function configuration.

2.7.22 qos trust cos [Function]

This command is used to enable QOS based on cos section in tag message, no command can


42

used to disable this function.

[Command Format]

[no] qos trust cos

[Command mode]



Configure QOS function of COS enable:

OPCOM3105 (config)# qos trust cos

[Relevant Commands]



show qos Show qos configuration information.

2.7.23 qos map cos-queue [Function]

This command is used to configure priority corresponding to COS value.

[Command Format]

qos map cos-queue cos0 cos1 cos2 cos3 cos4 cos5 cos6 cos7

[Parameter]

cos0-7: COS value from 0-7 corresponding priority number, 0 means the highest priority.

[Default]

cos0 - cos1: 0

cos2 – cos3: 1

cos4 – cos5: 2

cos6 – cos7: 3

[Command mode]



Configure QOS of COS to be cos0: 0, cos1: 1, cos2: 1, cos3: 1, cos4: 3, cos5: 3, cos6: 2, cos7: 2:

OPCOM3105 (config-eswif/1)# qos map cos-queue 0 1 1 1 3 3 2 2

[Relevant Commands]





43

2.7.24 show qos [Function]

This command is used to show qos configuration information.

[Command Format]

show qos

[Command mode]



Configure QOS confiugration information:

OPCOM3105 (config-eswif/0/1)# show qos

[Relevant Commands]




2.7.25 mac-address-table aging-time [Function]

This command is used to configure mac-address-table aging time.

[Command Format]

mac-address-table aging-time <0-3825>

[Parameter]

<0-3825>: aging time, unit : s.

[Default]

300s

[Command mode]


[Instructions]

System adopts hierarchical aging time, it will manual adopt 300, 75, 18, 1s automatically according to user configuration.


Configure MAC address table aging time to be 75:

OPCOM3105 (config)# mac-address-table aging-time 75

[Relevant Commands]


44


mac-address-table learning Configure mac learning function.

mac-address-table static HHHH.HHHH.HHHH vlan vlan_id port <1-4>

Add table item of static mac address.

mac-polling Configure mac address polling function.

show mac Show mac address table configuration information.

show mac-address-table ( all | static | dynamic ) [ port port-number | vlan vlan_id ]

Show mac address table information.

2.7.26 no mac-address-table aging-time [Function]

This command is used to configure mac-address-table aging time to defaulted value.

[Command Format]

no mac-address-table aging-time

[Default]

300s

[Command mode]



Configure MAC address table aging time to defaulted value:

OPCOM3105 (config)# no mac-address-table aging-time

[Relevant Commands]









2.7.27 mac-address-table learning [Function]

This command is used to configure mac-address learning function.

[Command Format]

mac-address-table learning (enable | disable)

[Parameter]


45

enable: MAC address learning enable ;

Disable: MAC address learning disable.

[Default]

enable

[Command mode]



Disable MAC address learning function:

OPCOM3105 (config)# mac-address-table learning disable

[Relevant Commands]


mac-address-table aging-time Configure mac address table aging time.







2.7.28 mac-address-table static HHHH.HHHH.HHHH vlan <2-4094> port <1-4> [Function]

This command is used to add static MAC address table, no command can used to delete static MAC address table.

[Command Format]

[no] mac-address-table static HHHH.HHHH.HHHH vlan <2-4094> port <1-4>

[Parameter]

HHHH.HHHH.HHHH: MAC address ;

<2-4094>: vlan ID;

<1-4>: switchport number.

[Default]

No static MAC address

[Command mode]


[Instructions]

Use mac-polling command to fulfill mac polling at first to get valid mac address information.



46

Add MAC address 0001.2345.6789 to vlan ID 12, transferring port is 3:

OPCOM3105 (config)# mac-address-table static 0001.2345.6789 vlan 12 port 3

[Relevant Commands]


mac-address-table aging-time Configure mac address table aging time.

mac-address-table learning Configure mac address table learning function.





2.7.29 mac-polling [Function]

This command is used to enable MAC address polling, no command can used to disable this function.

[Command Format]

[no] mac-polling

[Default]

No mac-polling

[Command mode]



Enable mac polling function:

OPCOM3105 (config)# mac-polling

[Relevant Commands]


mac-address-table learning Configure mac address learning function.


Add table item of static mac address table.




2.7.30 clear mac-address-table [Function]

This command is used to clear table item in mac address table.


47

[Command Format]

clear mac-address-table (all|dynamic|static)

[Parameter]

all: all table items;

dynamic: dynamic table items;

static: static table items.

[Command mode]



Clear all mac address table items:

OPCOM3105 (config)# clear mac-address-table all

Clear all static mac address table items:

OPCOM3105 (config)# clear mac-address-table static

Clear all dynamic mac address table items:

OPCOM3105 (config)# clear mac-address-table dynamic

[Relevant Commands]




Add static mac address table item.




2.7.31 search mac-address [Function]

This command is used to search mac address in current mac address table.

[Command Format]

search mac-address HHHH.HHHH.HHHH

[Parameter]

HHHH.HHHH.HHHH: MAC address.

[Command mode]




48

Search table item 000e.5e01.0203 in mac address table:

OPCOM3105 (config)# search mac-address 000e.5e01.0203

[Relevant Commands]




Add static mac address table item.




2.7.32 show mac [Function]

This command is used to show mac address learning function and aging time configuration information.

[Command Format]

show mac

[Command mode]



Show MAC address learning function and aging time configuration information:

OPCOM3105 (config)# show mac

[Relevant Commands]








2.8 Relevant command of sub-card E-SUBM-2FV35/FV35

2.8.1 bandwidth-config [Function]

This command is used to configure V35 timeslot bandwidth control mode.

[Command Format]

bandwidth-config (active|passive)


49

[Parameter]

active: active control mode;

passive: passive control mode.

[Default]

passive

[Command mode]

V35 interface configuration mode


Configure bandwidth control mode of V35 interface 1 to be passive control mode:

OPCOM3105 (config-v35/0/1/1)# bandwidth-config passive

[Relevant Commands]



2.8.2 interface [Function]

This command is used to enter interface configuration mode.

[Command Format]

interface (e1|v35) [<1-4>]

[Parameter]

(e1|eth): interface type. e1: E1 interface; v35: V35 interface;

[<1-4>]: interface number

[Command mode]

Remote configuration mode

[Instructions]

If not input interface index number, the interface number is 1.


Enter V35 interface 1:

OPCOM3105 (config-remote/0/1)# interface v35

2.8.3 no loopback [Function]

This command is used to cancel loopback of all ports.


50

[Command Format]

no loopback

[Command mode]



Cancel loopback of all ports:

OPCOM3105 (config-v35/0/1/1)# no loopback

[Relevant Commands]


show info Show information of sub-card device.

2.8.4 rxclk-phase [Function]

This command is used to configure receiving signal clock phase.

[Command Format]

rx-phasic (positive|negative)

[Parameter]

(positive|negative): clock phase;

positive: positive;

negative: negative.

[Default]

positive

[Command mode]

V35 interface configuration mode


Configure V35 interface 1 receiving signal clock phase to be positive:

OPCOM3105 (config-v35/0/1/1)# rxclk-phase positive

2.8.5 show info [Function]

This command is used to show sub-card information.

[Command Format]

show info

[Command mode]


51



Show sub-card configuration information:

OPCOM3105 (config-remote/0/1)# show info


This command is used to show sub-card interface information.

[Command Format]

show interface

[Command mode]

E1 interface configuration mode, V35 interface configuration mode


Show E1 interface 1 information:

OPCOM3105 (config-e1/0/1/1)# show interface

2.8.7 show version [Function]

This command is used to show sub-card version information.

[Command Format]

show version

[Command mode]



Show sub-card version information:

OPCOM3105 (config-remote/0/1)# show version

[Relevant Commands]


show info Show sub-card information.

2.8.8 v35-loopback [Function]

This command is used to configure V35 internal loopback.


52

[Command Format]

v35-loopback internal

[Command mode]



Configure V35 interface 1 remtoe internal loopback:

OPCOM3105 (config-v35/0/1/1)# v35-loopback internal

[Relevant Commands]



2.9 Relevant commands of clock configuration

2.9.1 device clock local [Function]

This command is used to configure internal device clock. no format command can delete clock source.

[Command Format]

device clock local priority <1-5> [quality (prc|ssua|ssub|sets|dnu| received)] no device clock local

[Parameter]

<1-5>: priority of clock;

(prc|ssua|ssub|sets|dnu|auto): clock quality grade. prc, reference clock comply with G.811; ssua, SSU-A clock comply with G.812; ssub, SSU-B clock comply with G.812; sets, device clock comply with G.813; dnu, can not used in synchronization; auto, scavenge automatically from receiving signal.

[Default]

Synchronization disable by default when quality grade is not match.

[Command mode]


[Instructions]

Configuration of quality grade can only be configured when SSM enable.


Set local run with priority 1, quality grade to be prc:

OPCOM3105(config)# device clock local priority 1 quality prc

[Relevant Commands]


53


show device clock Show device clock information.

2.9.2 device clock sdh-port [Function]

Configure SDH line clock source, no format command can delete clock source.

[Command Format]

device clock sdh-port <1-2> priority <1-5> [quality (prc|ssua|ssub|sets|dnu| received)] no device clock local sdh-port <1-2>

[Parameter]

<1-2>: SDH port number ;



[Default]


[Command mode]


[Instructions]



Set SDH port 1 clock with priority 1, quality grade to be prc:

OPCOM3105(config)# device clock sdh-port 1 local priority 1 quality prc

[Relevant Commands]



2.9.3 device clock e1 [Function]

Configure e1 line clock source, no format command can delete clock source.

[Command Format]

device clock e1 <1-4> priority <1-5> [quality (prc|ssua|ssub|sets|dnu| received)] no device clock local e1 <1-4>


54

[Parameter]

<1-4>: e1 port number ;



[Default]


[Command mode]


[Instructions]



Set e1 port 1 clock with priority 1, quality grade to be prc:

OPCOM3105(config)# device clock e1 1 local priority 1 quality prc

[Relevant Commands]



2.9.4 device clock clear local [Function]

Clear user commands acted on internal clock source to switch clock source with priority by automation.

[Command Format]

device clock clear local

[Command mode]



Clear user command of internal clock:

OPCOM3105(config)# device clock clear local

[Relevant Commands]




55

2.9.5 device clock clear sdh-port [Function]

Clear user commands acted on line clock source to switch clock source with priority by automation.

[Command Format]

device clock clear sdh-port <1-2>

[Parameter]

<1-2>: SDH port number ;

[Command mode]



Clear user command of SDH line clock 1:

OPCOM3105(config)# device clock clear sdh-port 1

[Relevant Commands]



2.9.6 device clock clear e1 [Function]

Clear user commands acted on line clock source to switch clock source with priority by automation.

[Command Format]

device clock clear e1 <1-4>

[Parameter]

<1-4>: e1 port number ;

[Command mode]



Clear user command of e1 line clock 1:

OPCOM3105(config)# device clock clear e1 1

[Relevant Commands]




56

2.9.7 device clock force-switch local [Function]

Force switch clock source to local clock source.

[Command Format]

device clock force-switch local

[Command mode]



Force switch to local clock source:

OPCOM3105(config)# device clock force-switch local

[Relevant Commands]



device clock clear Clear user commands.

device clock mode Configure device clock mode.

2.9.8 device clock force-switch sdh-port [Function]

Switch to SDH line clock source by force.

[Command Format]

device clock force-switch sdh-port <1-2>

[Parameter]

<1-2>: SDH port index.

[Command mode]



Force switch clock to SDH line clock 2:

OPCOM3105 (config)# device clock force-switch sdh-port 2

[Relevant Commands]






57

2.9.9 device clock force-switch e1 [Function]

Switch clock source by force.

[Command Format]

device clock force-switch e1 <1-4>

[Parameter]

<1-4>: e1 port index.

[Command mode]



Force switch clock to e1 line clock 2:

OPCOM3105 (config)# device clock force-switch e1 2

[Relevant Commands]





2.9.10 device clock lockout local [Function]

Lock out clock source.

[Command Format]

device clock lockout local

[Default]

Lockout disable

[Command mode]


[Instruction]

Use command clear to cancel clock source lockout state.


Lockout local clock:

OPCOM3105 (config)# device clock lockout local

[Relevant Commands]



58



2.9.11 device clock lockout sdh-port [Function]


[Command Format]

device clock lockout local sdh-port <1-2>

[Parameter Explanation]

<1-2>: SDH port index

[Default]

Lockout disable

[Command mode]


[Instruction]



Lockout SDH line clock 1:

OPCOM3105 (config)# device clock lockout sdh-port 1

[Relevant Commands]




2.9.12 device clock lockout e1 [Function]


[Command Format]

device clock lockout local e1 <1-4>

[Parameter]

<1-4>: e1 port index

[Default]

Lockout disable

[Command mode]


59


[Instruction]



Lockout e1 line clock 2:

OPCOM3105 (config)# device clock lockout e1 2

[Relevant Commands]




2.9.13 device clock manual-switch local [Function]

This command is used to switch clock source by manual.

[Command Format]

device clock manual-switch local

[Command mode]



Manual switch clock to local clock:

OPCOM3105 (config)# device clock manual-switch local

[Relevant Commands]





2.9.14 device clock manual-switch sdh-port [Function]


[Command Format]

device clock manual-switch sdh-port <1-2>

[Parameter]



60

[Command mode]



Manual switch clock to SDH line clock 2:

OPCOM3105 (config)# device clock manual-switch sdh-port 2

[Relevant Commands]





2.9.15 device clock manual-switch e1 [Function]


[Command Format]

device clock manual-switch e1 <1-4>

[Parameter]


[Command mode]



Manual switch clock to e1 line clock 2:

OPCOM3105 (config)# device clock manual-switch e1 2

[Relevant Commands]





2.9.16 device clock pll [Function]

Configure working state of device clock phase lock loop.

[Command Format]

device clock pll (lock |freerun)


61

[Parameter]

(lock |freerun): work state of phase lock loop; lock, lock trace mode; freerun, free running mode (switch to local run for OPCOM3105).

[Default]

Lock mode by default

[Command mode]



Set current device pll works in free run mode:

OPCOM3105 (config)# device clock pll freerun

[Relevant Commands]



2.9.17 device clock reset local [Function]

Reset clock source in abnormal state.

[Command Format]

device clock reset local

[Command mode]



Reset local clock:

OPCOM3105 (config)# device clock reset local

[Relevant Commands]



2.9.18 device clock reset sdh-port [Function]


[Command Format]

device clock reset sdh-port <1-2>

[Parameter]


62


[Command mode]



Reset SDH line clock 2:

OPCOM3105 (config)# device clock reset sdh-port 2

[Relevant Commands]



2.9.19 device clock reset e1 [Function]


[Command Format]

device clock reset e1 <1-4>

[Parameter]


[Command mode]



Reset e1 line clock 2:

OPCOM3105 (config)# device clock reset e1 2

[Relevant Commands]



2.9.20 device clock wait-to-restore-time 【Function Explanation】

Configure wait time to restore time.

device clock wait-to-restore-time <0-12>

【Command Mode】

<0-12>: wait time of switching from clock with lower priority to clock with higher priority in process of higher priority clock restore. Recorded in minute, 0 means doesn’t need to wait.


63

【Default Case】

1 minute

【Command Mode】


【Application Example】

Set to be don’t need wait to restore:

OPCOM3105(config)# device clock restore-time 0

【Related Command】

Command Description

device clock Configure clock source.

device clock slot Configure line clock source.


2.9.21 device clock ssm 【Function Explanation】

Configure SSM mode for device clock.

device clock ssm (standard |extend |disable)

【Command Mode】

(standard |extend |disable): starting items of SSM function; standard, start standard SSM function; extend, start extend SSM function; disable, disable SSM function.

【Default Case】

disable

【Command Mode】



Set standard SSM function enable:

OPCOM3105(config)# device clock ssm standard


Command Description

device clock Configure clock source.

device clock slot Configure line clock source.



64

2.9.22 device clock local id 【Function Explanation】

Configure clock source ID.

device clock local id <0-15>

【Command Mode】

<0-15>: clock source ID.

Command Mode】



Clear local clock ID 8:

OPCOM3105(config)# device clock local id 8


Command Description


2.9.23 device clock sdh-port id 【Function Explanation】


device clock sdh-port <1-2> id <0-15>

【Command Mode】

<1-2>: SDH port index


Command Mode】



Clear SDH line clock 1 ID 8:

OPCOM3105(config)# device clock sdh-port 1 id 8


Command Description



65

2.9.24 device clock e1 id 【Function Explanation】


device clock e1 <1-4> id <0-15>

【Command Mode】

<1-4>: e1 port index


Command Mode】



Clear e1 line clock 1 ID 8:

OPCOM3105(config)# device clock e1 1 id 8


Command Description


2.9.25 show device clock [Function]

This command is used to show device clock information.

[Command Format]

show device clock

[Command mode]



Configuer clock information:

OPCOM3105 # show device clock

[Relevant Commands]



device clock manual-switch Configure manual switch clock source.

device clock sdh-port 1 priority 1 Configure clock priority.


66

2.10 system configuration command

2.10.1 dcc select [Function]

This command is used to select DCC channel type.

[Command Format]

dcc select (d1d2d3|e1channel)

[Parameter]

(d1d2d3|e1channel): d1d2d3: use SDH overhead byte d1d2d3 to transmit network management information;

e1channel: use e1 channel to transmit network management information.

[Default]

Use SDH overhead byte d1d2d3 to transmit network management information.

[Command mode]


[Instructions]

E1 channel corresponding timeslot need to configure when use e1 channel to transmit network management information, the E1 port transmitting network management information generally use port 9-10, port 9 is east optical port corresponding network management channel, port 10 is west optical port corresponding network management channel.


Select to use overhead byte d1d2d3 for transmitting network management information:

OPCOM3105 (config)# dcc select d1d2d3

[Relevant Commands]


show info Show current device information.

2.10.2 e1-retiming-src [Function]

This command is used to select E1 retiming clock source.

[Command Format]

e1-retiming-src (osc|e1-1|e1-2|e1-3|e1-4)

[Parameter]

(osc|e1-1|e1-2|e1-3|e1-4): osc: use local clock as retiming clock source;

e1-1: use e1 port 1 receiving clock as retiming clock source;



67


e1-4: use e1 port 4 receiving clock as retiming clock source.

[Default]

Use local clock as retiming clock source.

[Command mode]



Select to use E1 port 1 receiving clock as retiming clockc source:

OPCOM3105 (config)# e1-retiming-src e1-1

[Relevant Commands]



2.10.3 e1 <1-4> retiming [Function]

This command is used to select E1 port enable retiming function or not.

[Command Format]

e1 <1-4> retiming (enable|disable)

[Parameter]

<1-4>: select E1 port;

(enable|disable): E1 retiming function enable/disable.

[Default]

All ports E1 retiming function disable.

[Command mode]



Select to enable E1 port 1 retiming function:

OPCOM3105 (config)# e1 1 retiming enable

[Relevant Commands]




68

Chapter 3 Reference Materials

chinese All modes

clear All modes

config Privileged mode

device unlock Privileged mode

device lock Global mode

device clock-mode Global mode

disable Privileged mode

enable Common mode

english All modes

end Global mode, interface mode

exit All modes

help All modes

interface Global mode

history All modes

hostname Privileged mode

list All modes

logout Privileged mode

quit All modes

reboot Privileged mode

settime Privileged mode

show clock Privileged mode

show cpu-utilization-ratio Privileged mode

show device Privileged mode, Global mode

show device clock Privileged mode

show sntp Privileged mode

show terminal Privileged mode

show version Privileged mode

sntp server Global mode

sntp broadcast client Global mode

terminal history Common mode

terminal line Common mode

terminal time-out Common mode

who Privileged mode

device assetid Global mode


69

device description Global mode

show opt-device Privileged mode, Global mode

password Privileged mode

show user Privileged mode

user Privileged mode

user privilege Privileged mode

save user Privileged mode

log Global mode

log clear Global mode

show log Privileged mode, Global mode

arp add Global mode

arp delete Global mode

ip address Snmp interface mode

ip route Global mode

ping Privileged mode, Global mode

show arp Privileged mode, Global mode

show ip route Privileged mode, Global mode

show snmp-server community Privileged mode, Global mode

show snmp trap-server Privileged mode, Global mode

snmp-server community Global mode

snmp-server contact SYSCONTACT Global mode

snmp-server location SYSLOCATION Global mode

snmp-server name SYSNAME Global mode

snmp trap-server Global mode

snmpd Global mode

show snmp-server statistics Privileged mode, Global mode

show interface snmp Privileged mode, Global mode

download Privileged mode

erase startup-config Privileged mode

show running-config Privileged mode

show startup-config Privileged mode

upload Privileged mode

write Privileged mode

alarm-trap-disable Global mode


70

alarm-trap-disable index Global mode

port-trap-disable Global mode

show current-alarm Privileged mode, Global mode

show history-alarm Privileged mode, Global mode

show alarmindex Privileged mode, Global mode

show alarmindex index Privileged mode, Global mode

show port-trap-disable Privileged mode, Global mode

interface eth Global mode, eth interface mode

autonegotiate eth interface mode

description eth interface mode

shutdown eth interface mode

show interface Privileged mode, eth interface mode

speed eth interface mode

duplex eth interface mode

auto-mdix eth interface mode

flow-control eth interface mode

reset statistic eth interface mode

interface vcg Global mode

show vcg Privileged mode, vcg configuration mode

encapsulation vcg configuration mode

gfp-fcs vcg configuration mode

reset statistic vcg configuration mode

description Interface configuration mode

interface sdh Global mode, sdh interface mode

j0mode Interface configuration mode

loopback Interface configuration mode

sdh es-threshold Interface configuration mode

sdh exc-threshold Interface configuration mode

sdh ais-insert Interface configuration mode

sdh reset-statistics debug

sdh overhead c2 Interface configuration mode

sdh overhead j0 Interface configuration mode

sdh overhead j1 Interface configuration mode

sdh overhead s1 Interface configuration mode

sdh sd-threshold Interface configuration mode

sdh ses-threshold Interface configuration mode


71

sdh aupje-threshold Interface configuration mode

show interface sdh Privileged mode, interface mode

interface dcc Global mode, dcc interface mode

shutdown Interface configuration mode

ip unnumbered Interface configuration mode

ip address Interface configuration mode

echo-time Interface configuration mode

echo retry times Interface configuration mode

auto-connect Interface configuration mode

show interface dcc Privileged mode, interface mode


72

Appendix A Acronyms

Acronyms list 1

Acronyms Full spelling

ADM Add-Drop Multiplexer

AIS Alarm Indication Signal

APS Automatic Protection Switching

AU Administrative Unit

AU-n Administration Unit，level n

AUG Administration Unit Group

AU-PTR Administration Unit Pointer

BBE Background Block Error

BBER Background Block Error Ratio

BER Bit Error Ratio

CMI Coded Mark Inversion

C-n Container- n

CORBA Common Object Request Broker Architecture

CV Code Violation

DCC Data Communications Channel

DCE Data Circuit-terminating Equipment

DCF Data Communications Function

DCN Data Communications Network

DDN Digital Data Network

DTE Data Terminal Equipment

DXC Digital Cross Connect

ECC Embedded Control Channel

EM Element Management


73

Acronyms list 2

Acronyms Full spelling

EML Element Management Layer

EMS Element Management System

EOS Ethernet Over SDH

ES Error Second

ESR Error Second Ratio

ETSI European Telecommunication Standards Institute

FEBBE Far End Background Block Error

FEES Far End Error Second

FESES Far End Severely Error Second

GUI Graphical User Interface

HDLC High Digital Link Control

HPC Higher order Path Connection

IP Internet Protocol

ITU-T International Telecommunication Union-Telecommunication

Standardization Sector

L2 Layer 2

LAN Local Area Network

LCT Local Craft Terminal

LOF Loss Of Frame

LOP Loss Of Pointer

LOS Loss Of Signal

LPC Lower order Path Connection

MAC Medium Access Control

MAN Metropolitan Area Network

MCU Micro Control Unit

MD Mediation Device

MF Mediation Function

MII Medium Independent Interface

MM Multi Mode

MS Multiplex Section

Address: 2nd Floor, South Building of Rainbow Plaza, No.11 Shangdi Information Road, Haidian District, Beijing Postcode: 100085 Tel: +86-10-82883305 Fax: +86-10-82883056 Email: [email protected] http://www.raisecom.com

Documents

OPCOM3105 Commands Notebook 200811