Embed Size (px)
Citation preview
Operating and installation instructionsRangehood
To prevent the risk of accidents or damage to the appliance, it isessential to read these instructions before it is installed and used forthe first time.
en-AU, NZ M.-Nr. 10 553 490
Contents
2
Warning and Safety instructions .......................................................................... 4
Caring for the environment ................................................................................ 13
Guide to the appliance ........................................................................................ 14
Description of the functions ............................................................................... 16
Operation.............................................................................................................. 17Switching the fan on.............................................................................................. 17Selecting a power setting...................................................................................... 17Fan run-on after cooking ....................................................................................... 17Switching the fan off ............................................................................................. 17Switching the cooktop lighting on/off ................................................................... 17Power management .............................................................................................. 17
Switching Power management on/off .............................................................. 18Safety switch-off ................................................................................................... 18
Energy saving tips ............................................................................................... 19
Cleaning and care ............................................................................................... 20Housing ................................................................................................................. 20Grease filters ......................................................................................................... 21NoSmell active charcoal filter................................................................................ 24
Disposing of the charcoal filter......................................................................... 24Reactivatable charcoal filter ............................................................................. 24
Changing a lamp ................................................................................................... 25
Installation............................................................................................................ 26Before installation.................................................................................................. 26Protective foil......................................................................................................... 26Installation instructions.......................................................................................... 26Dismantling............................................................................................................ 26Assembly parts...................................................................................................... 27Appliance dimensions ........................................................................................... 29Safety distance (S) ................................................................................................ 30Installation recommendations ............................................................................... 31Drilling diagram for wall mounting......................................................................... 31
Connection for air extraction ............................................................................. 32Condensate trap.................................................................................................... 33Silencer.................................................................................................................. 33
Electrical connection .......................................................................................... 35
Contents
3
After sales service and warranty ....................................................................... 36Position of the data plate ...................................................................................... 36Warranty ................................................................................................................ 36
Technical data...................................................................................................... 37Note for test institutes ........................................................................................... 37
Warning and Safety instructions
4
This appliance complies with all relevant local and national safetyrequirements. Inappropriate use can, however, lead to personalinjury and damage to property.
To avoid the risk of accidents and damage to the appliance, pleaseread these instructions carefully before using it for the first time.They contain important notes on the safety, installation, use andmaintenance of the appliance. Miele cannot be held liable for non-compliance with these instructions.
Keep these instructions in a safe place and ensure that all usersare familiar with the contents. Pass them on to any future owner ofthe appliance.
Correct application
This rangehood is designed for domestic use and for use in similarenvironments by guests in hotel or motel rooms, bed & breakfastsand other typical living quarters. This does not include common/shared facilities or commercial facilities within hotels, motels or bed& breakfasts.
The appliance is not suitable for outdoor use.
It must only be used to extract vapours and remove odours fromcooking.Any other usage is at the owner's risk. Miele cannot be held liable fordamage resulting from incorrect or improper use or operation.
Where a recirculation rangehood is fitted above a gas cooktop,please ensure that there is an adequate supply of fresh air into theroom in which it is installed. Please seek the advice of a qualified gasfitter if necessary.
Warning and Safety instructions
5
This appliance is not intended for use by persons (includingchildren) with reduced physical, sensory or mental capabilities, orlack of experience and knowledge, unless they have been givensupervision or instruction concerning its use by a person responsiblefor their safety, and are able to recognise the dangers of misuse.
Safety with children
Young children must not be allowed to use this appliance.
Older children may only use the appliance when its operation hasbeen clearly explained to them and they are able to use it safely,recognising the dangers of misuse.
Cleaning work may only be carried out by older children under thesupervision of an adult.
Children should be supervised near the appliance. Ensure thatthey do not play with the appliance.
The cooktop lighting is very intense.Ensure, in particular, that babies/small children do not look directlyat the light.
Danger of suffocation!Whilst playing, children may become entangled in packagingmaterial (such as plastic wrapping) or pull it over their head with therisk of suffocation. Keep packaging material away from children.
Warning and Safety instructions
6
Technical safety
Unauthorised installation, maintenance and repairs can causeconsiderable danger for the user. Installation, maintenance andrepairs must only be carried out by a Miele authorised technician.
A damaged appliance can be dangerous. Check it for visible signsof damage. Do not use a damaged appliance.
The electrical safety of this appliance can only be guaranteedwhen continuity is complete between it and an effective earthingsystem. It is most important that this basic safety requirement ispresent and tested regularly and, where there is any doubt, thehousehold wiring system should be inspected by a qualifiedelectrician.
Reliable and safe operation of this rangehood can only be assuredif it has been connected to the mains electricity supply.
The connection data (voltage and frequency) on the data plate ofthe rangehood must match the mains electricity supply in order toavoid the risk of damage to the rangehood.Compare this before connecting the appliance to the mainselectricity. If in doubt, consult a qualified electrician.
Do not connect the appliance to the mains electricity supply by amulti-socket unit or an extension lead. Extension leads are a firehazard and do not guarantee the required safety of the appliance.
Warning and Safety instructions
7
For safety reasons, this appliance may only be used after it hasbeen built in.
This rangehood must not be installed and operated in mobileinstallations (e.g. on a ship).
Tampering with electrical connections or components andmechanical parts is highly dangerous to the user and can causeoperational faults. Only open the housing as described in the instructions given in theinstallation sheet and in the “Cleaning and care” section of thisbooklet. Under no circumstances should any other parts of thehousing be opened.
The manufacturer's warranty will be invalidated if the appliance isnot repaired by a Miele approved service technician.
Faulty components must only be replaced by genuine Miele spareparts. The manufacturer can only guarantee the safety of theappliance when Miele replacement parts are used.
If the mains connection cable is damaged, it must only bereplaced by a Miele authorised service technician or suitablyqualified electrician in order to avoid a hazard.
During installation, maintenance and repair work, the appliancemust be disconnected from the mains electricity supply. It is onlycompletely isolated from the electricity supply when:
– the mains circuit breaker is switched off, or
– it is switched off at the wall socket and the plug is withdrawn fromthe socket. Do not pull the mains connection cable but the mainsplug to disconnect your appliance from the mains electricitysupply.
Warning and Safety instructions
8
Using at the same time as other heating appliances that depend on the airfrom the room
Warning - danger of toxic fumes!Great care should be taken when using the rangehood at the sametime and in the same room or area of the house as another heatingappliance which depends on the air in the room.Such appliances include gas, oil, wood or coal-fired boilers andheaters, continuous flow or other water heaters, gas cooktops, orovens which draw air in from the room and duct exhaust gases outthrough a chimney or extraction ducting.
When used in extraction mode, with or without an external motorfitted, or in recirculation mode with a recirculation box installedoutside the room, the appliance draws air in from the room inwhich it is installed and from neighbouring rooms.If there is insufficient air, an underpressure will occur. The heatingappliance will be starved of oxygen, impairing combustion.Harmful gases could be drawn out of the chimney or extractionducting back into the room, with potentially fatal consequences.
Warning and Safety instructions
9
In order to ensure safe operation, and to prevent gases given offby the heating appliances from being drawn back into the roomwhen the rangehood and the heater are in operationsimultaneously, an underpressure in the room of 0.04 mbar (4 pa)is the maximum permissible.
Ventilation can be maintained by air inlets which cannot beblocked, in windows, doors or outside wall vents, or by othertechnical measures, such as ensuring that the rangehood can onlybe switched on when the heating appliance is switched off or viceversa. A ventilation brick alone is not generally sufficient to ensuresafe ventilation.
The overall ventilation condition of the dwelling must be taken intoaccount. If in any doubt, the advice of a competent builder, or forgas a qualified gas fitter (registered with an official gas safety bodyin accordance with national safety regulations), must be sought.
If the rangehood is used in recirculation mode, where the air isdirected back into the room in which it is located, operating aheating appliance which depends on the room air at the same timeis not hazardous.
Warning and Safety instructions
10
Correct use
Never use an open flame beneath the rangehood. To avoid thedanger of fire, do not flambé or grill over an open flame.When switched on, the rangehood could draw flames into the filter.Fat deposits could ignite, presenting a fire hazard.
The rangehood can become damaged when exposed to excessiveheat.
– When using the rangehood over a gas cooktop, ensure that anyburners in use are always covered by a pan. Switch the cookingzone off when a pan is removed, even for a short time.
– Select a pan which is suitable for the size of the burner.
– Regulate the flame so that it does not burn up the sides of thepan.
– Avoid overheating the pan (e.g. when cooking with a wok).
Always switch the rangehood on when a cooking zone is in use,otherwise condensation may collect in the rangehood, which couldcause corrosion.
Overheated oil and fat can ignite, causing fire damage to therangehood.When cooking with oil or fat, chip pans and deep fat fryers etc., donot leave the pans unattended. Similarly, never leave an open grillunattended when grilling.
Warning and Safety instructions
11
Do not use the rangehood without the filters in place. This wayyou will avoid the risk of grease and dirt getting into the applianceand hindering its smooth operation.
The rangehood can get very hot during cooking due to heat risingfrom the cooktop.Do not touch the housing or the grease filters until the rangehoodhas cooled down.
This rangehood is not suitable for placing objects on.
Correct installation
Refer to the cooktop manufacturer's instructions as to whether arangehood may be operated above the cooktop.
Safety regulations prohibit the fitting of a rangehood over solidfuel stoves.
An insufficient safety distance between the stovetop and therangehood can result in damage to the rangehood.The minimum safety distances between the top of the stovetop andthe bottom of the rangehood given in the “Installation” section of thisbooklet must be observed, unless the stovetop manufacturer statesthat a greater safety distance is required.If more than one cooking appliance is fitted beneath the rangehood,and they have different minimum safety distances to the rangehood,select the greater distance.
The distances given in “Installation” must be observed whenfitting the rangehood.
Metal parts can have sharp edges which may cause injury.Wear gloves to protect your hands from being cut.
All ducting, pipework and fittings must be of non-flammablematerial. These can be obtained from builders' merchants.
Warning and Safety instructions
12
The appliance must not be connected to a chimney or vent fluewhich is in current use for exhausting fumes from appliances burninggas or other fuels. Neither should it be connected to ducting whichventilates rooms with fireplaces.
If exhaust air is to be extracted into a chimney or ventilation ductno longer used for other purposes, seek professional advice.
Cleaning and care
There is a risk of fire if cleaning is not carried out as described inthese operating instructions.
Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a shortcircuit.
In areas which may be subject to infestation by cockroaches orother vermin, pay particular attention to keeping the machine and itssurroundings in a clean condition at all times. Any damage whichmay be caused by cockroaches or other vermin will not be coveredby the machine warranty.
Accessories
Use only genuine original Miele spare parts. If spare parts oraccessories from other manufacturers are used, the warranty will beinvalidated, and Miele cannot accept liability.
Caring for the environment
13
Disposal of the packingmaterialThe transport and protective packaginghas been selected from materials whichare environmentally friendly fordisposal, and can normally be recycled.
Recycling the packaging reduces theuse of raw materials in themanufacturing process and alsoreduces the amount of waste in landfillsites. Ensure that any plasticwrappings, bags etc. are disposed ofsafely and kept out of the reach ofbabies and young children. Danger ofsuffocation.
Disposing of your oldapplianceElectrical and electronic appliancesoften contain valuable materials. Theyalso contain specific materials,compounds and components, whichwere essential for their correct functionand safety. These could be hazardousto human health and to the environmentif disposed of with your domestic wasteor if handled incorrectly. Please do not,therefore, dispose of your old appliancewith your household waste.
Please dispose of it at your localcommunity waste collection / recyclingcentre for electrical and electronicappliances. You are also responsible fordeleting any personal data that may bestored on the appliance prior todisposal. Please ensure that your oldappliance poses no risk to childrenwhile being stored prior to disposal.
Guide to the appliance
14
Guide to the appliance
15
a Telescopic extension piece
b Tower
c Canopy
d Controls
e Grease filters
f Recirculation grilles(only for recirculation mode)
g Cooktop lighting
h NoSmell active charcoal filter(special accessory for recirculation mode)
i On/Off touch control for the fan
j Touch controls to select the fan power setting
k On/Off touch control for the cooktop lighting
Description of the functions
16
Depending on the model of therangehood, the following options areavailable:
Air extraction mode
The air is drawn in and cleaned by thegrease filters and directed outside.
Non-return flap
The non-return flap is designed toprevent the exchange of room andoutside air taking place.The flap is closed when the rangehoodis switched off.When the rangehood is switched on,the non-return flap opens for thecooking vapours to be blown directlyoutside.
If the on-site ventilation system doesnot have a non-return flap, the non-return flap supplied must be fitted.
Recirculation mode(available as an optional extra with aconversion kit and charcoal filter: see“Technical Data”)
The air is drawn in and cleaned first bythe grease filters and then by a charcoalfilter. The cleaned air is thenrecirculated back into the kitchen.
Operation
17
Switching the fan onSwitch the fan on as soon as you startcooking. This is to ensure that vapoursare captured right from the start.
Press the On/Off touch control .
The fan will switch on at setting 2. The symbol and 2 will light up in thepower setting display.
Selecting a power settingFor light to heavy cooking vapours andodours, select from power settings 1 to3.
For short periods of cooking food withintensive vapours and a strong aroma,e.g. when searing meat, select Boostersetting B.
Select the power level you want bypressing the or controls.
Reducing power down from theBooster setting
If Power management is activated(default setting), the fan automaticallyswitches back to level 3 after 5 minutes.
Fan run-on after cooking It is advisable to run the fan for a few
minutes after cooking has finished toneutralise any lingering vapours andodours in the air.
Switching the fan off Press the On/Off touch control to
switch the fan off.
The symbol will go out.
Switching the cooktop lightingon/offThe cooktop lighting can be switchedon and off independently of the fan.
To do so press the lighting control .
The symbol will light up when thecooktop lighting is switched on.
Power managementThe rangehood features a Powermanagement system to help saveenergy. The fan power setting isreduced and the lighting is switched offautomatically.
– If the Booster setting has beenselected, the fan will automaticallyswitch to setting 3 after 5 minutes.
– From settings 3, 2 or 1 the power willbe reduced by one setting after2 hours and then in 30-minute stagesuntil the fan finally switches off.
– The cooktop lighting will switch offautomatically after 12 hours.
Operation
18
Switching Power management on/off
You can deactivate the Powermanagement.Keep in mind that this may increaseenergy consumption.
To set this option, both the fan andthe cooktop lighting must beswitched off.
Press the and controls at thesame time for approx. 10 seconds,until the 1 lights up.
Then press in turn:
– the lighting control ,
– then the touch control, and
– the lighting control again.
If Power management is switched on,the 1 and B indicators light upconstantly.When it is switched off, the 1 and Bindicators flash.
Press to switch Powermanagement off.
The 1 and B indicators will flash.
To switch it on, press .
The 1 and B indicators will light upconstantly.
Confirm your choice with the On/Offcontrol .
All the indicator lights will go out.
If you don't confirm your selectionwithin 4 minutes, the rangehood willautomatically revert to the previoussetting.
Safety switch-offIf Power management has beendeactivated, the rangehood will switchitself off automatically after 12 hours if ithas been left on (fan and cooktoplighting).
To switch it back on press the On/Off control or the lightingcontrol .
Energy saving tips
19
This rangehood operates very efficientlyand economically. The following willhelp you to save even more energywhen using it:
– Ensure that there is sufficientventilation in the kitchen whencooking. In extraction mode, if thereis insufficient air flow the rangehoodcannot operate efficiently and thiscauses increased operating noiselevels.
– Always cook with the lowest possiblesetting. This produces fewer cookingvapours, so you can use a lowerrangehood power level and thereforebenefit from reduced energyconsumption.
– Check the power level selected onthe rangehood. A lower power level isgenerally sufficient for the majority ofcooking. Only use the Booster settingwhen necessary.
– When a large volume of cookingvapours are being produced, switchto a high power level in good time.This is more efficient than operatingthe rangehood for longer to try tocapture cooking vapours which havealready been distributed throughoutthe kitchen.
– Make sure that you switch therangehood off after use.
– Clean or change the filters at regularintervals. Heavily soiled filters reduceperformance, increase the risk of fireand are unhygienic.
Cleaning and care
20
Before proceeding with anymaintenance or cleaning task, therangehood must be disconnectedfrom the power supply (see “Warningand Safety instructions”).
Housing
General
The surfaces and controls aresusceptible to scratches andabrasion.Please observe the followingcleaning instructions.
All external surfaces and controls canbe cleaned using warm water with asmall amount of washing-up liquidapplied with a well wrung-out softsponge or cloth.
Do not use too much water whencleaning the controls.Water could penetrate into theelectronics and cause damage.
After cleaning, wipe the surfaces dryusing a soft cloth.
Do not use:
– cleaning agents containing soda,acids, chlorides or solvents,
– abrasive cleaning agents, e.g.powder cleaners or cream cleanersand abrasive sponges, as well as potscourers or sponges which havebeen used previously with abrasivecleaning agents. These will damagethe surface material.
Important for appliances withstainless steel surfaces
(This information does not apply to thecontrols)
Stainless steel surfaces can becleaned with a proprietary non-abrasive cleaning agent designedspecifically for use on stainless steel,e.g. Original Miele ceramic andstainless steel cooktop cleaner.
To help prevent re-soiling, aproprietary conditioning agent forstainless steel (Original Miele Careproduct for stainless steel) can alsobe used.Apply sparingly with a soft clothfollowing the instructions on thepackaging.
Important for appliances withlacquered housing
(special order finish)
Observe the general notes oncleaning earlier in this section.
Minor scratches on the surface areinevitable when cleaning the housing.Depending on the lighting in thekitchen, this may negatively affect theappliance's appearance.
Cleaning and care
21
Important for the controls
Do not leave soiling on the controlsfor any length of time.Otherwise they may sufferdiscolouration or damage.Remove any soiling immediately.
Observe the general notes oncleaning earlier in this section.
Do not use stainless steel cleaningagents on the controls.
Grease filtersThe re-usable metal grease filters in theappliance remove solid particles(grease, dust, etc.) from the kitchenvapours, preventing soiling of therangehood.
The grease filters must be cleaned atregular intervals.
Heavily soiled grease filters hinder airextraction and will lead to increasedlevels of soiling in the rangehood andin the kitchen.
Fire hazard!Oversaturated grease filters are a firehazard.Clean the grease filters at regularintervals.
Grease filter cleaning intervals
Accumulated grease solidifies over alonger period of time and makescleaning more difficult. The greasefilters should therefore be cleaned every3 to 4 weeks.
Removing the grease filter
When handling the grease filter,be careful not to drop it.This can result in damage to the filterand the cooktop below.Make sure you hold the filter securelyat all times when handling it.
Cleaning and care
22
To take out the grease filter, releasethe locking clip on the filter, lower thefilter approx. 45°, unhook it at theback and remove it.
Cleaning the grease filters by hand
Clean the filters with a soft nylonbrush in a mild solution of hot waterand a small amount of washing-upliquid. Do not use undiluted washingup liquid.
Unsuitable cleaning agents
Unsuitable cleaning agents can causedamage to the surface of the filters ifused regularly.Do not use:
– cleaning agents containing descalingagents,
– powder cleaners or cream cleaners,
– aggressive all-purpose cleaningagents or spray cleaners for grease,
– oven sprays.
Cleaning the grease filters in thedishwasher
Place the grease filters upright orslightly inclined in the lower basket.Ensure the spray arm is notobstructed.
Use a standard householddishwasher detergent.
Select a dishwasher programme witha wash temperature between 50 °Cand 65 °C.
Depending on the detergent used,cleaning the filters in the dishwashermay cause the inside filter surfaces tobecome discoloured. This will notaffect the functioning of the greasefilters in any way.
After cleaning
After cleaning, leave the filters to dryon an absorbent surface beforerefitting them.
When removing the filters forcleaning, also clean off any residuesof oil or fat from the now accessiblehousing to prevent the risk of thesecatching fire.
Replace the grease filters, makingsure that the locking clips are facingdown towards the cooktop.
Cleaning and care
23
If a grease filter is inadvertentlyrefitted upside down, insert a smallscrewdriver blade into the slit todisengage the clip.
Cleaning and care
24
NoSmell active charcoal filterWith recirculation mode, a charcoalfilter must be fitted in addition to thegrease filters. The charcoal filter isdesigned to absorb cooking odours.
The charcoal filter is fitted in the canopyabove the grease filters.
Fitting/replacing the charcoal filter
Remove the grease filters beforefitting or replacing the charcoal filter.
Take the charcoal filter out of itspackaging.
Press the charcoal filter into theframe.
Refit the grease filters.
When to change the NoSmell activecharcoal filter
Replace the charcoal filter when it nolonger absorbs kitchen odourseffectively.It should be replaced at least every 6months.
Disposing of the charcoal filter
The used charcoal filter can bedisposed of with the normalhousehold waste.
Reactivatable charcoal filter
A reactivatable charcoal filter isavailable for this rangehood. Byreactivating it in an oven, it can bereused several times.
It is supplied with its own installationand usage instructions which mustbe observed.
Charcoal filters are available to order viathe Miele online shop (see end of thisbooklet for contact details) or directlyfrom Miele.
The charcoal filters are listed under“Technical data” at the back of thisbooklet.
Cleaning and care
25
Changing a lamp
Use only the lamps specified for usewith this appliance.Other lamps, e.g. halogen lamps,may be damaged due to the highgeneration of heat.
The lamps should be replaced with thefollowing:
Manufacturer ............................... EGLOLamp type .................................... GU10Specification................................ 12981Wattage ........................................... 3 WILCOS D Code...... DR-3-H-GU10-50/56
These lamps are available from Miele.
Switch off the fan and the lighting.
The lamps can get very hot whenin use.Allow the lamps to cool down for afew minutes before changing them.
Disconnect the rangehood from theelectricity supply before replacing thelamps (see “Warning and Safetyinstructions”).
Insert the lever supplied into the gapbetween the lamp and the lampholder.
The lamp will drop downwards.
Grip the lamp, turn it anti-clockwiseand take it out.
Screw the new lamp into the socketand push it upwards. Please followthe manufacturer's instructions.
Installation
26
Before installation
Before installation, it is importantto read the information given on thefollowing pages as well as the“Warning and Safety instructions” atthe beginning of this booklet.
Protective foilThe housing components haveprotective foil around them to preventthem from transport damage.
Please remove this foil before fittingthe housing components. It can bepeeled off easily.
Installation instructionsSee enclosed installation sheet forinstructions on how to install thisappliance.
Failure to install the screws orfixing device in accordance withthese instructions may result inelectrical hazards.
DismantlingShould the appliance ever need to bedismantled, follow the installationinstructions in reverse order asdescribed on the installation sheet. Alever is supplied to assist with theremoval of the tower.
Unscrew the two fixing screws on thetower.
Push the lever between the tower andthe extension piece.
Lever the tower out of its fixings.
Installation
27
Assembly parts
Installation
28
a 3 protective sheetsfor use when fitting the tower.
b 1 exhaust connectionfor exhaust ducting 150 mm.
c 1 reducing collarfor exhaust ducting 125 mm.
d 1 non-return flapfor installation in the exhaustconnection on the motor unit (not forrecirculation mode). The non-returnflap may already be fitted dependingon model.
e Wall bracketfor securing the rangehood to thewall.
f Conversion kit for recirculationmodeincluding directional unit, flexiblealuminium hose and hose clips (theconversion kit is not supplied. It isavailable as an optional extra - see“Technical data”).
8 screws, 5 x 60 mm and
8 plugs, 8 x 50 mmfor securing the wall bracket.
The screws and plugs aredesigned for use in solid walls only.For other types of wall construction,alternative fixings will be required.Make sure the wall is able to take theweight of the rangehood.
2 x M 6 self-tapping nutsfor securing the canopy.
2 screws 3.9 x 7.5 mmfor securing the tower.
Keep the following in a safe place:
Montage
Installation
Montaje
M
ontaggio
Montering
Montagem
A
sennus
Installation instructions
1 leverfor replacing lamps and for dismantlingthe tower.
Installation
29
Appliance dimensions
The drawing is not to scale.
Installation
30
a Extraction
b Recirculation
c Ventilation grille positioned at the top for recirculation
de (only d is required for recirculation mode rangehoods): The shaded arearepresents the wall or ceiling area for the vent cut-out and for fitting theconnection socket. Recirculation mode rangehoods only require an electricalconnection socket.
Connection for air extraction 150 mm, or 125 mm with reducing collar.
Safety distance (S)
The minimum distances between the cooking surface of a cooktop (pansupport(s) for gas models) and the bottom of the rangehood are as follows,unless a greater distance is specified by the manufacturer of your cookingappliance. See also “Warning and Safety instructions”.
Cooking appliance Minimum distance S
Electric cooktop 600 mm (AU, NZ)450 mm (HK, MY, SG, TH)
Electric grill, deep fat fryer (electric) 650 mm
Multi-burner gas cooktop with maximum 45.4 MJ/htotal output, with no burner having a greater outputthan 16.2 MJ/h.
650 mm
Multi-burner gas cooktop with total output greaterthan 45.4 MJ/h, but with a maximum of 77.8 MJ/h,with no burner having a greater output than17.3 MJ/h.
760 mm
Multi-burner gas cooktop with total output greaterthan 77.8 MJ/h, with a single burner having agreater output than 17.3 MJ/h.
Not possible
Single burner gas cooktop with a maximum outputof 21.6 MJ/h.
650 mm
Single burner gas cooktop with an output greaterthan 21.6 MJ/h, but with a maximum of 29.2 MJ/h.
760 mm
Single burner gas cooktop with an output greaterthan 29.2 MJ/h.
Not possible
Installation
31
Installation recommendations– When deciding on the safety distance
between the cooktop and rangehood,please note that a distance of 650mm above electric cooktops may bepreferable to give more workingspace under the rangehood.
– Account should also be taken of theheight of the person who will beusing the rangehood most often.They should have sufficient space towork comfortably at the cooktop, andbe able to reach the rangehoodcontrols with ease.
– If positioned too high, extraction willbe inefficient.
– To achieve optimum vapourextraction, the rangehood must bepositioned centrally over the cooktop,not to the side.
– The cooktop should be no wider thanthe rangehood and, if possible, itshould be narrower, especially forsafety distances greater than750 mm.
– The installation area must be easilyaccessible. The rangehood should beeasily accessible and easy todismantle in the event that service isrequired. This should be taken intoconsideration when planning theposition of cupboards, shelves,ceilings or features in the vicinity ofthe rangehood.
Drilling diagram for wallmounting Please follow the directions given in
the installation instructions suppliedfor drilling.
For pre-installation of a back wallwhere the holes have to be pre-drilled, please refer to the drillingdistances in the drawing above(screws 5 mm).
*The dimension for the middle wallbracket is variable. It will depend on theposition of the wall vent and the socket.It should be set as low as possible.
Connection for air extraction
32
Before installation, it is importantto read the information given on thefollowing pages as well as the“Appliance dimensions” and the“Warning and Safety instructions” atthe beginning of this booklet. This isparticularly crucial when using therangehood at the same time as aheating appliance that relies onoxygen from the same room, whichcould result in the build-up of toxicfumes.The rangehood should be installedaccording to local and nationalbuilding regulations. Seek approvalfrom the building inspector wherenecessary.
Only use smooth pipes or flexiblehoses made from non-flammablematerials for the extraction ducting.
To achieve the greatest possible airextraction with the lowest noise level,please note the following:
– The diameter of the exhaust ductingshould not be less than 150 mm.
– If flat ducting is being used, thecross-sectional area must not besmaller than the cross-sectional areaof the exhaust connection.
– The exhaust ducting should be asshort and straight as possible.
– Only use wide radius bends.
– The exhaust ducting must not bekinked or compressed.
– Ensure that all connections arestrong and airtight.
Remember that any constriction ofthe airflow will reduce extractionperformance and increase operatingnoise.
If the exhaust is ducted through anoutside wall, a telescopic wall vent ora roof vent (available as an optionalaccessory) is recommended.
If the exhaust air is to be ducted intoa vent flue, the ducting must bedirected in the flow direction of theflue.
When ducting is horizontal, it must belaid to slope away at at least 1 cm permetre. This is to ensure thatcondensate cannot drain back intothe rangehood.
If the exhaust ducting is to runthrough rooms, ceiling space etc.where there may be great variationsin temperature between the differentareas, the problem of condensationwill need to be addressed. Theexhaust ducting will need to besuitably insulated.
Connection for air extraction
33
Condensate trap
In addition to insulating the exhaustducting, we recommend that a suitablecondensate trap is also installed tocollect and evaporate any condensatewhich may occur.Condensate traps are available for125 mm or 150 mm ducting.
When installing a condensate trap,ensure that it is positioned verticallyand, if possible, directly above theexhaust socket.The arrow on the housing indicatesthe direction of airflow.
Silencer
To achieve even further reductions innoise levels, a special silencer (optionalaccessory) can be fitted in the ductingsystem.
Air extraction mode
The silencer not only reduces noisefrom the motor outside the house, butalso sounds from outside (e.g. trafficnoise). For this reason, the silencermust be positioned as close as possibleto the ducting exit .
Connection for air extraction
34
Recirculation mode
The silencer needs to be positionedbetween the exhaust connection andthe directional unit . Ensure there isadequate space in the tower for fittingit.
Electrical connection
35
All electrical work must beundertaken by a suitably qualifiedand competent person in strictaccordance with current national andlocal safety and building coderegulations. Installation, repairs andother work by unqualified personscould be dangerous, for which themanufacturer cannot be held liable.Ensure power is not supplied to theappliance until after installation orrepair work has been carried out.
The rangehood must be connected to asuitably earthed socket (AC 230 V,50 Hz).
For extra safety it is advisable to installa residual current device (RCD) with atrip current of 30 mA.
Connection of this appliance must bemade via a suitable isolator switchwhich provides disconnection on allpoles and which complies with nationaland local safety regulations. Theisolator switch should be easilyaccessible after the appliance has beenbuilt in.
If the mains socket is not accessibleafter installation, an additional means ofdisconnection must be provided for allpoles. There must be an all-polecontact gap of 3 mm in the switch(including switch, fuses and relays).
The connection data is given on thedata plate (See “After sales service”).Ensure that this data matches thehousehold mains supply.
After sales service and warranty
36
In the event of a fault which you cannotremedy yourself, please contact Miele.
The contact details for Miele are givenat the back of these instructions.
When contacting Miele, please quotethe model and serial number of yourappliance.These can be found on the data plate.
Position of the data plateThe data plate is visible after removingthe grease filters.
WarrantyAU, NZ:
The manufacturer's warranty for thisappliance is 2 years.
For further information, please refer toyour warranty booklet.
Other countries:
For information on the appliancewarranty specific to your country pleasecontact Miele. See the end of thisbooklet for contact details.
Technical data
37
Fan motor 295 W
Cooktop lighting
PUR 68 W 2 x 3 W
PUR 98 W 3 x 3 W
Total rated load
PUR 68 W 301 W
PUR 98 W 304 W
Voltage, frequency AC 230 V, 50 Hz
Fuse rating 10 A
Mains connection cable length 1.5 m
Weight
PUR 68 W 21 kg
PUR 98 W 25 kg
Optional accessory for recirculation mode
DUW 20 kit to convert from extraction mode to recirculation mode and charcoalfilter DKF 12-1 or DKF 12-R (reactivatable).
Note for test institutes
Note for comparative testing
Data quoted in the following data sheets was calculated in accordance with thecurrent standards EN 61501 and EN 60704-3. The distance between the areabeing measured/stovetop and the underside of the rangehood is 600 mm and thevoltage 230 V for test purposes. Testing is carried out without a non-return valve.
www.miele.com.au
Miele Experience Centre and Head Office Melbourne:1 Gilbert Park DriveKnoxfield, VIC 3180
Miele Experience Centre South Melbourne:206-210 Coventry StreetSouth Melbourne, VIC 3205
Miele Experience Centre and Office Sydney:3 Skyline PlaceFrenchs Forest, NSW 2086
Miele Experience Centre and Office Brisbane:39 Harvey Street NorthEagle Farm, QLD 4009
Miele Experience Centre and Office Perth:
83-85 Sir Donald Bradman DriveHilton, SA 5033
205-207 Stirling HighwayClaremont, WA 6010
Miele Experience Centre and Office Adelaide:
Miele Australia Pty. Ltd.
Miele New Zealand Limited
Level 2, 10 College HillFreemans Bay, Auckland 1011
Miele Experience CentreAuckland:8 College HillFreemans Bay, Auckland 1011Telephone:0800 464 353 (0800 4 MIELE)www.miele.co.nz
Miele Global HeadquartersGermanyMiele & Cie. KGCarl-Miele-Straße 2933332 GüterslohFederal Republic of Germany
Head Office:
IRD 98 463 631
ACN 005 635 398ABN 96 005 635 398
Miele Experience Centre Gold Coast:131 Ferry RoadSouthport, QLD 4215
M.-Nr. 10 553 490 / 02en-AU, NZ
PUR 68 WPUR 98 W
