Operator Acceptance Values for Device Antenna Performance

GSM Association Non-confidential

Official Document TS.24 - Operator Acceptance Values for Device Antenna Performance

V3.0 Page 1 of 14

Operator Acceptance Values for Device Antenna Performance

Version 3.0

01 October 2015

This is a Non-binding Permanent Reference Document of the GSMA

Security Classification: Non-confidential

Access to and distribution of this document is restricted to the persons permitted by the security classification. This document is confidential to the

Association and is subject to copyright protection. This document is to be used only for the purposes for which it has been supplied and

information contained in it must not be disclosed or in any other way made available, in whole or in part, to persons other than those permitted

under the security classification without the prior written approval of the Association.

Copyright Notice

Copyright © 2015 GSM Association

Disclaimer

The GSM Association (“Association”) makes no representation, warranty or undertaking (express or implied) with respect to and does not accept

any responsibility for, and hereby disclaims liability for the accuracy or completeness or timeliness of the information contained in this document.

The information contained in this document may be subject to change without prior notice.

Antitrust Notice

The information contain herein is in full compliance with the GSM Association’s antitrust compliance policy.



V3.0 Page 2 of 14

Table of Contents

1 Introduction 3

1.1 Overview 3

1.2 Scope 3

1.3 Definition of Terms 4

1.4 Document Cross-References 4

2 Antenna Performance Requirements 5

2.1 Antenna Performance Calculation Formula 5

2.2 Operator Antenna Performance Acceptance Values for 2G and 3G Bands 5

2.3 Operator Antenna Performance Acceptance Values for LTE Bands 7

3 Moving Forward 9

Annex A Measured Values 10

A.1 RAG Status Tables: 10

A.1.1 Test Methodology 10

A.1.2 Interpretation 10

A.1.3 Measured Results Tables 11

A.1.4 Further Analysis 13

Document Management 14

Document History 14

Other Information 14



V3.0 Page 3 of 14

1 Introduction

1.1 Overview

Mobile handset design has changed significantly over the past few years. Antennas, which were external in many cases, moved inside the terminal and evolved to be light-weight and low-volume.

The increasing focus on design conflicts with radio performance of the antenna systems can lead to service disruption and increased dropped call rates impacting customer experience. Increasing network density is not an option as it may not be viable in many cases.

Whilst the 3GPP standards define the absolute global minimum OTA performance requirements to be met by devices, numerous operators are already requesting higher values in their own procurement activities to serve customer needs and network rollout plans.

However, the test methods used and antenna performance values requested by the various operators differ widely, leaving vendors with a fragmented requirements landscape.

To facilitate this alignment and agreement, the antenna experts of operators within the GSMA Terminal Steering Group have reviewed results of antenna performance tests (conducted within their own organisations as well as by the GSMA), and have aligned test methods and agreed on performance values to be used as guidelines for acceptable and achievable performance of antennas in Mobile devices. The values are supported by operators representing the USA, Europe and Asia regions.

Following the publication of version two, dedicated to 2G and 3G bands in February 2014 [TS.24], the TSG operators have now aligned performance also for the LTE bands, which have been added TS24 V3.0.

1.2 Scope

This document defines the Operator Acceptance Values for Device Antenna Performance. The values are determined taking into consideration

devices being held close to head with left and right hand

devices being held with one hand only for the purpose of Browsing

devices being measured with the Free Space method

The requirements (which include measurement uncertainty) are relevant for mobile devices, including feature phones, smart phones, tablets and dongles. More details can be found in the relevant sections.

These GSMA Operator Acceptance Values for Device Antenna Performance are non-binding, and operators are free to request alternative values as required. It will be up to each individual operator to adopt and enforce the GSMA Operator OTA requirements.

These values serve to align, enhance and promote antenna performance requirements across the industry while seeking to improve device antenna performance and network interoperability.

Note: the alignment of the GSMA Operator Acceptance Values for Device Antenna Performance does not impact the test process; this will continue as is the case today in Operator-Manufacturer bilateral agreements.

Each phase of the work carried out in updating TS.24 has also involved independent tests on commercially available Smartphones. The purpose of these tests was to benchmark the Acceptance Values defined in TS.24.



V3.0 Page 4 of 14

In this version of TS.24 we publish the results of these tests in Appendix 1

1.3 Definition of Terms

Term Description

3GPP 3rd Generation Partnership Project

BHH Beside Head and Hand

BHHL Beside Head and Hand Left

BHHR Beside Head and Hand Right

CS Circuit Switched (voice mode)

CTIA Cellular Telecommunications & Internet

Association

FDD Frequency Division Duplex

FS Free Space

GSM / E-GSM Global System for Mobile Communication/

Extended-GSM

GSMA GSM Association

LTE Long Term Evolution

MIMO Multiple Input Multiple Output

OTA Over The Air (without cable)

RB Resource Block

RMC Reference Measurement Channel

TDD Time Division Duplex

TRP Total Radiated Power

TRS Total Radiated Sensitivity

TSG Terminal Steering Group

TSGFM Terminal Steering Group Full Memebers

VoLTE Voice over LTE

VoIP Voice over Internet Protocol

WCDMA Wideband Code Division Multiple Access

1.4 Document Cross-References

Ref Document

Number Title

CTIA 3.4.2 or later

Test Plan for Wireless Device Over the Air Performance

http://www.ctia.org/docs/default-source/default-document-

library/ctia_ota_test_plan_rev_3_4_2.pdf?sfvrsn=2

3GPP TS 25.144 User Equipment (UE) and Mobile Station (MS) over the air

performance requirements

http://www.ctia.org/docs/default-source/default-document-library/ctia_ota_test_plan_rev_3_4_2.pdf?sfvrsn=2

http://www.ctia.org/docs/default-source/default-document-library/ctia_ota_test_plan_rev_3_4_2.pdf?sfvrsn=2



V3.0 Page 5 of 14

2 Antenna Performance Requirements

The following table serves as an internal guideline for mobile operators, who are encouraged to apply the required values in their bilateral agreements with their vendors.

2.1 Antenna Performance Calculation Formula

Table 1: Antenna Performance Calculation Formula

Note:

a) The values include measurement uncertainty.

b) Operators may accept alternative values for bands outside of their home market.

2.2 Operator Antenna Performance Acceptance Values for 2G and 3G Bands

The following tables list the Operator Antenna Performance Values per test scenario and frequency band (2G and 3G).

Req ID Requirement

TSG24_AP_01

For the scenario “Head and Hand” (BHH) and in line with CTIA, the terminal SHALL support an average value of the low, medium and high frequency channels, on both, the left (BHHL) and right (BHHR) hand-side, a performance equal to or above the GSMA performance requirements for that frequency band listed in table 1 and 2 in section 2.2 for 2G/3G and table 3 and 4 in section 2.3 for LTE bands.

TSG24_AP_02

For the scenario “Browsing” and in line with CTIA, the terminal SHALL support an average value of the low, medium and high frequency channels, on both the left and right hand-side, a performance equal to or above the GSMA performance requirements for that frequency band listed in table 1 and 2 in section 2.2 for 2G/3G and table 3 and 4 in section 2.3 for LTE bands.

TSG24_AP_03

For the scenario “Free Space” (FS) and in line with CTIA, the terminal SHALL support an average value of the low, medium and high frequency channels a performance equal to or above the GSMA performance requirements for that frequency band listed in table 1 and 2 in section 2.2 for 2G/3G and table 3 and 4 in section 2.3 for LTE bands.

TSG24_AP_04 No measured channel SHALL be 1 dB worse than the performance values defined for that frequency band.



V3.0 Page 6 of 14

Test scenario:

Head and Hand (BHH):

Relevant for devices that support voice and do not exceed the maximum dimensions specified for hand phantom (i.e.72 mm) [CTIA]. The values are defined considering head and hand and are relevant for left or right hand.

Browsing:

Relevant for devices where the display is visible to the end user for data usage and where width ranges between 56 mm and 72 mm [CTIA]. The values are defined considering one-hand only and are relevant for left or right hand. The 3G frequencies are measured, using a 12.2 Kbps reference measurement channel (RMC).

Free Space:

Relevant for any device that embeds an antenna, including devices wider than 72 mm that support voice. The applicable measurement method is voice (CS) mode. The 3G frequencies are measured, using a 12.2 Kbps reference measurement channel (RMC).

These acceptance values include measurement uncertainty.

Frequency Band 2G/3G

GSMA Operator Acceptance Values for TRP [dBm]

BHH Browsing Free Space

GSM 850 20.0 24.0 27.0

EGSM 900 20.0 25.0 28.0

GSM 1800 21.0 23.0 26.0

GSM 1900 21.0 23.0 26.0

WCDMA Band 1 15.0 17.0 20.0

WCDMA Band 2 16.5 17.0 20.0

WCDMA Band 3 13.5 14.7 17.7

WCDMA Band 5 11.0 14.7 17.7

WCDMA Band 8 11.0 15.0 18.0

WCDMA Band 19 11.0 15.5 18.0

Table 2 GSMA Operator Acceptance Values for TRP for 2G and 3G bands

Frequency Band 2G/3G

GSMA Operator Acceptance Values for TRS [dBm]


GSM 850 -97.0 -99.0 -103.0

EGSM 900 -95.0 -99.0 -103.0

GSM 1800 -99.0 -100.0 -104.0

GSM 1900 -99.5 -100.0 -103.0



V3.0 Page 7 of 14

WCDMA Band 1 -101.0 -103.0 -106.0

WCDMA Band 2 -98.5 -101.0 -104.0

WCDMA Band 3 -98.5 -99.0 -102.0

WCDMA Band 5 -94.5 -100.0 -103.0

WCDMA Band 8 -96.0 -101.0 -104.0

WCDMA Band 19 -96.0 -102.0 -104.5

Table 3 GSMA Operator Acceptance Values for TRS for 2G and 3G bands

2.3 Operator Antenna Performance Acceptance Values for LTE Bands

The following tables list the Operator Antenna Performance Values per test scenario and

frequency band (LTE).

Test scenario:

Head and Hand (BHH):

Relevant for devices that support voice (e.g. VoLTE, VoIP) and do not exceed the maximum

dimensions specified for hand phantom (i.e.72 mm) [CTIA].

Browsing:

Relevant for devices where the display is visible to the end user for data usage and where

width ranges between 56mm and 72 mm [CTIA]. The values are defined considering one-

hand only and are relevant for left or right hand.

Free Space:

Relevant for any device that embeds an antenna, including devices wider than 72 mm that

support voice (e.g. VoLTE, VoIP).

These acceptance values include measurement uncertainty.

Settings during testing

TRP:

Single antenna transmitting

Uplink RB Allocation : 12

TRS:

All receivers/antennas active

Downlink RB Allocation: 50

Bandwidth: 10 MHz



V3.0 Page 8 of 14

Frequency Band LTE

GSMA Operator Acceptance Values for TRP [dBm]


FDD Band 1 13.5 15.5 18.5

FDD Band 2 13.5 15.5 18.5

FDD Band 3 13.5 15.5 18.5

FDD Band 4 13.5 15.5 18.5

FDD Band 5 9.8 14.3 18.0

FDD Band 7 13.5 15.5 18.5

FDD Band 8 9.8 14.3 18.0

FDD Band 11 11.5 14.5 18.0

FDD Band 12 9.8 14.3 18.0

FDD Band 13 9.8 14.3 18.0

FDD Band 17 9.8 14.3 18.0

FDD Band 18 9.8 14.3 18.0

FDD Band 19 9.8 14.3 18.0

FDD Band 20 9.8 14.3 18.0

FDD Band 21 11.5 14.5 18.0

FDD Band 25 13.5 15.5 18.5

FDD Band 26 9.8 14.3 18.0

FDD Band 28 9.8 14.3 18.0

TDD Band 38 13.5 15.5 18.5

TDD Band 39 13.5 15.5 18.5

TDD Band 40 13.5 15.5 18.5

TDD Band 41 13.5 15.5 18.5

TDD Band 42 13.5 15.5 18.5

TDD Band 43 13.5 15.5 18.5

Table 4: GSMA Operator Acceptance Values for TRP for the LTE Bands



V3.0 Page 9 of 14

Frequency Band LTE

GSMA Operator Acceptance Values for TRS [dBm]


FDD Band 1 -89.0 -91.0 -94.0

FDD Band 2 -89.0 -91.0 -94.0

FDD Band 3 -89.0 -91.0 -94.0

FDD Band 4 -89.0 -91.0 -94.0

FDD Band 5 -85.0 -89.5 -93.5

FDD Band 7 -89.0 -91.0 -94.0

FDD Band 8 -85.0 -89.5 -93.5

FDD Band 11 -87.0 -90.0 -93.5

FDD Band 12 -85.0 -89.5 -93.5

FDD Band 13 -85.0 -89.5 -93.5

FDD Band 17 -85.0 -89.5 -93.5

FDD Band 18 -85.0 -89.5 -93.5

FDD Band 19 -85.0 -89.5 -93.5

FDD Band 20 -85.0 -89.5 -93.5

FDD Band 21 -87.0 -90.0 -93.5

FDD Band 25 -89.0 -91.0 -94.0

FDD Band 26 -85.0 -89.5 -93.5

FDD Band 28 -85.0 -89.5 -93.5

TDD Band 38 -89.0 -91.0 -94.0

TDD Band 39 -89.0 -91.0 -94.0

TDD Band 40 -89.0 -91.0 -94.0

TDD Band 41 -89.0 -91.0 -94.0

TDD Band 42 -89.0 -91.0 -94.0

TDD Band 43 -89.0 -91.0 -94.0

Table 5 GSMA Operator Acceptance Values for TRS for the LTE Bands

3 Moving Forward

As part of Phase 4, the GSMA operators will progress:

Alignment of MIMO OTA test method and performance for LTE frequency bands

Antenna performance values for devices supporting voice which are wider than 72

mm.

In addition, operators will continue to test antenna performance of market devices and actively monitor and/or engage in work driven in relevant industry bodies.



V3.0 Page 10 of 14

Annex A Measured Values

As part of the process to derive the harmonised Operator Acceptance Values published in this document the GSMA has, for each phase of the work, carried out independent tests on commercially available Smartphones. These devices are taken from consumer stock, and are not prototype or engineering samples provided by the OEM’s.

In this appendix we have published the results from these tests.

The purpose of the tests was to benchmark the acceptance values defined in TS.24 and to ensure that they represent a realistic achievable target that manufacturers of devices can readily achieve.

All device results have been anonymised.

A.1 RAG Status Tables:

The tables published in this appendix include a RAG (Red Amber Green) colour coding. This RAG status can be interpreted as follows

Green = meets or surpasses the GSMA TS.24 acceptance value

Amber = within 2 dB of the GSMA TS.24 acceptance value

Red = fails to meet the GSMA TS.24 acceptance value by a value greater than 2 dB

The 2 dB margin used to define the Amber category reflects that the acceptance values published in this document are a harmonised average of the values contributed by operators who took part in this work.

It also recognises that some operators have a small tolerance in their acceptance values so that they do not block the launch of a device that marginally fails to meet their requirements. These tolerances are usually defined on a bilateral basis and are reviewed per device.

Because of the above the tables below try to reflect this reality through use of the 2 dB margin which defines values in Amber.

A.1.1 Test Methodology

Device selection was based on a random selection of commercially available devices at the time of measurement, typically these devices are from Tier 1 OEM’s, and are their Flagship or high volume selling products.

The tests were carried out in an independent antenna lab, accredited by both CTIA (e.g. a CATL) and GCF (Global Certification Forum).

The specific test methodologies used followed the recommendations issued by CTIA.

A.1.2 Interpretation

For the purposes of this work these tables were used to assess the values defined in TS.24, and to ensure that when the 2 dB margin is taken into account, the significant majority of devices are able to meet or surpass the acceptance values published in TS.24.



V3.0 Page 11 of 14

A.1.3 Measured Results Tables

Table 6: TRP and TRS RAG status of tested devices in 2G/3G bands for the use cases

Browsing and Free Space (status: 2013)

TRP and TRS

[dBm]

2G/3G Frequency

BandBrowsing

Free

Space Browsing FS Browsing FS Browsing FS Browsing FS Browsing FS Browsing FS Browsing FS Browsing FS Browsing FS

GSM 850 24,0 27,0

EGSM 900 25,0 28,0

GSM 1800 23,0 26,0

GSM 1900 23,0 26,0

WCDMA Band 1 17,0 20,0 14,72 17,99 14,55 16,79 19,50 21,57 16,97 20,21 16,45 19,46 17,62 19,84 20,15 18,30 16,72

WCDMA Band 2 17,0 20,0 15,66 18,97 17,98 20,21 16,11 18,96 17,82 14,24

WCDMA Band 5 14,7 17,7 12,73 15,94 6,13 19,45 14,68 19,34 13,79 17,56 16,43 14,76

WCDMA Band 6 14,7 17,7 14,77 19,65

WCDMA Band 8 15,0 18,0 13,74 17,08 4,39 20,53 15,83 18,91 14,25 18,92 20,91 18,75 17,30

WCDMA Band 19 15,5 18,0 14,89 20,09

GSM 850 -99,0 -103,0

EGSM 900 -99,0 -103,0

GSM 1800 -100,0 -104,0

GSM 1900 -100,0 -103,0

WCDMA Band 1 -103,0 -106,0 -107,16 -109,21 -105,12 -107,46 -109,19 -111,10 -103,28 -107,64 -108,08 -110,84 -109,65 -111,12 -108,27 -105,52 -106,86

WCDMA Band 2 -101,0 -104,0 -104,16 -106,71 -110,05 -111,57 -105,06 -108,11 -106,33 -107,68

WCDMA Band 5 -99,0 -102,0 -104,30 -107,39 -95,42 -110,94 -106,91 -109,64 -102,99 -107,05 -110,62 -103,39

WCDMA Band 6 -100,0 -103,0 -106,94 -109,73

WCDMA Band 8 -101,0 -104,0 -100,89 -104,13 -98,98 -107,94 -102,08 -105,55 -102,47 -106,91 -110,36 -106,84 -104,32

WCDMA Band 19 -102,0 -104,5 -106,36 -110,03

Device 5 Device 6 Device 7 Device 8 Device 9Operator

AcceptanceDevice 1 Device 2 Device 3 Device 4



V3.0 Page 12 of 14

Table 7: TRP and TRS RAG status of tested devices in 2G/3G bands for head & hand

use case (status: 2013)

TRP and TRS [dBm]Operator

Acceptance

GSM 850 Dual 2G+3G 20,0 20,53 20,73 22,65 17,88 21,83 21,73 18,05 18,62 13,26 16,37 15,27 17,43 22,78 22,31

EGSM 900 Dual 2G+3G 20,0 20,49 19,95 20,89 16,03 20,47 22,26 17,54 19,25 17,33 19,12 16,44 17,90 20,19 22,54 22,00 22,06 16,88 16,79

GSM 1800 Dual 2G+3G 21,0 20,31 19,50 21,48 20,84 22,20 22,11 15,74 19,11 20,23 20,33 21,29 19,94 20,47 16,88 21,00 19,46 19,98 19,88

GSM 1900 Dual 2G+3G 21,0 19,90 19,69 20,32 20,35 21,18 20,72 18,02 17,80 20,91 20,01 21,76 20,41 20,71 18,62 23,42 21,99

WCDMA Band 1 Dual 2G+3G 15,0 13,90 13,06 13,55 13,12 15,17 15,01 11,71 11,15 14,14 13,06 14,79 13,28 14,69 12,94 16,35 16,54 14,30 14,77

WCDMA Band 2 Dual 2G+3G 16,5




WCDMA Band 8 Dual 2G+3G 11,0 12,19 6,97 9,51 11,67 6,67 9,68 6,94 8,24 10,88 13,32 8,32 9,09


GSM 850 2G only 20,0

EGSM 900 2G only 21,0

GSM 1800 2G only 22,0

GSM 1900 2G only 21,0

GSM 850 Dual 2G+3G -97,0 -97,16 -96,94 -96,02 -94,88 -97,29 -97,97 -93,54 -96,28 -90,06 -90,89 -96,14 -96,76 -98,79 -98,57

EGSM 900 Dual 2G+3G -95,0 -94,36 -93,89 -94,47 -91,94 -95,33 -96,62 -91,70 -93,12 -93,56 -95,12 -93,04 -93,76 -94,05 -96,89 -96,46 -95,84 -91,90 -92,82

GSM 1800 Dual 2G+3G -99,0 -98,40 -97,64 -100,18 -99,63 -100,32 -99,78 -95,40 -96,61 -99,96 -99,39 -99,51 -98,88 -99,02 -96,29 -100,81 -100,10 -99,81 -99,65

GSM 1900 Dual 2G+3G -99,5 -98,85 -97,89 -97,84 -97,90 -101,08 -100,52 -96,81 -97,03 -99,73 -98,66 94,63 -99,35 -98,47 -96,56 -99,98 -99,76

WCDMA Band 1 Dual 2G+3G -101,0 -97,88 -97,47 -100,01 -100,85 -102,28 -101,24 -99,04 -97,82 -99,75 -99,46 -102,99 -101,67 -100,53 -98,10 -101,30 -102,23 -101,65 -101,04

WCDMA Band 2 Dual 2G+3G -98,5




WCDMA Band 8 Dual 2G+3G -96,0 -98,58 -94,33 -95,82 -97,69 -93,39 -96,08 -94,59 -94,90 -95,74 -98,76 -94,44 -95,29


GSM 850 2G only -97,0

EGSM 900 2G only -97,0

GSM 1800 2G only -99,0

GSM 1900 2G only -99,5

Device 9Device 3 Device 4 Device 5 Device 6 Device 7 Device 8

BHHL BHHR BHHL

Phone Type Device 1 Device 2

BHHR BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHLBHH2G/3G Frequency Band

TRP and TRS [dBm]Operator

Acceptance

GSM 850 Dual 2G+3G 20,0

EGSM 900 Dual 2G+3G 20,0 16,86 17,73 19,52 18,55 18,58 21,44 19,34 19,47 20,83 20,48 18,70 19,92 17,31 15,96 18,20 19,80 20,04 18,75

GSM 1800 Dual 2G+3G 21,0 23,55 19,35 21,49 23,19 20,10 20,32 20,86 21,79 19,74 19,17 19,91 20,85 19,38 17,62 21,44 20,53 21,13 20,94

GSM 1900 Dual 2G+3G 21,0

WCDMA Band 1 Dual 2G+3G 15,0 17,36 15,48 15,21 16,25 16,20 16,41 15,33 16,79 15,22 14,47 13,56 14,76 16,17 15,26 15,76 14,04 16,40 15,47





WCDMA Band 8 Dual 2G+3G 11,0 7,28 8,28 11,98 10,58 10,47 13,75 11,83 11,81 8,62 9,16 10,24 9,40 9,86 11,33 11,38 10,79


GSM 850 2G only 20,0

EGSM 900 2G only 21,0

GSM 1800 2G only 22,0

GSM 1900 2G only 21,0

GSM 850 Dual 2G+3G -97,0

EGSM 900 Dual 2G+3G -95,0 -91,57 -94,48 -95,93 -97,57 -93,73 -97,67 -96,32 -96,57 -96,66 -93,98 -93,06 -93,07 -93,12 -90,98 -93,74 -95,00 -94,66 -95,24

GSM 1800 Dual 2G+3G -99,0 -102,05 -98,61 -101,71 -102,86 -98,96 -99,20 -101,02 -102,35 -99,44 -99,17 -100,00 -101,28 -98,86 -97,24 -100,89 -99,54 -100,68 -100,72

GSM 1900 Dual 2G+3G -99,5

WCDMA Band 1 Dual 2G+3G -101,0 -105,54 -102,90 -102,42 -102,42 -104,99 -104,73 -100,31 -102,30 -101,60 -101,77 -98,95 -99,55 -100,73 -100,69 -101,99 -101,01 -100,19 -99,45





WCDMA Band 8 Dual 2G+3G -96,0 -93,81 -95,47 -98,30 -96,86 -97,30 -101,33 -99,96 -99,09 -95,24 -94,86 -94,96 -91,93 -95,98 -96,58 -96,53 -96,99


GSM 850 2G only -97,0

EGSM 900 2G only -97,0

GSM 1800 2G only -99,0

GSM 1900 2G only -99,5

Device 13 Device 14Phone Type

2G/3G Frequency BandBHH

Device 10 Device 11 Device 12 Device 15 Device 16 Device 17 Device 18

BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHL BHHR BHHL


11,81 12,90 12,43 15,30 16,89 15,82 15,67 12,59

11,93 14,81

13,60 13,26 12,52 13,83 13,36 16,21 15,18 13,16 14,92 12,90

16,95 12,81

8,23 11,02 6,39 4,82

10,98 12,79 14,50 9,62 11,74 17,45

11,71 10,70 7,81 6,15

10,96 11,24

9,90 10,71 11,90 12,68

11,80 9,78 9,27 7,77 8,11 7,14

13,04 9,73 11,33 11,95

15,59 16,02 14,98 13,30 13,33 11,48

11,77 12,77 12,60 11,54 10,52 9,51

12,24 16,65 13,70 15,87 13,63 4,31

FDD Band 1

FDD Band 2

FDD Band 3

Device 8 Device 9Device 2 Device 3 Device 4 Device 5 Device 6 Device 7TRP [dBm]Operator

AcceptanceDevice 1

LTE Frequency

Band

13,50

13,50

13,50

FDD Band 18

TDD Band 41

TDD Band 42

TDD Band 43

13,50

9,75

9,75

13,50

13,50

13,50

FDD Band 4

FDD Band 5

FDD Band 7

FDD Band 8

FDD Band 11

FDD Band 12

FDD Band 19

FDD Band 20

FDD Band 21

FDD Band 25

FDD Band 26

FDD Band 28

TDD Band 38

TDD Band 39

TDD Band 40

FDD Band 13

FDD Band 17

BHH

13,50

13,50

13,50

13,50

9,75

13,509,75

11,50

9,75

9,75

9,75

9,75

9,75

9,75

11,50



V3.0 Page 13 of 14

Table 8: TRP RAG status of tested devices in LTE bands for head & hand use case

(status: 2015)

Table 9: TRS RAG status of tested devices in LTE bands for head & hand use case

(status: 2015)

A.1.4 Further Analysis

As part of the results analysis it was noticed that there could be a perceived trend that demonstrates a difference between left hand and right hand performance. Further analysis of this trend is required to establish if this is a genuine trend or just an anomaly in the results. The TSGFM Group would like to draw attention to this as it was noted that accreditation in some regions is still limited to testing with the right hand, and therefore there could be a correlation between this and some products being optimized for performance in the right hand.

The sample of measured product is too small to establish if this trend is real, but it has been noted for further study during future measurement and test campaigns carried out by GSMA.


-87,73 -88,31 -89,36 -89,49 -91,51 -90,20 -87,82 -86,95

-90,35 -90,78

-91,37 -92,09 -89,03 -88,84 -88,79 -89,70 -92,28 -91,42 -89,55 -88,38

-91,74 -92,00

-85,87 -86,87 -82,61 -81,86

-92,46 -93,47 -88,88 -84,24 -86,69 -89,01

-85,72 -84,99 -85,01 -84,34

-86,65 -89,06

-86,17 -87,97 -86,25 -86,66

-86,68 -87,19 -87,08 -86,30 -83,99 -82,84

-89,46 -89,76 -89,74 -90,06

-91,09 -91,95 -92,40 -92,04 -89,17 -87,24

-85,76 -86,08 -87,45 -86,66 -86,97 -85,02

-88,89 -92,02 -87,74 -89,16 -90,48 -84,86

Device 6 Device 7 Device 8 Device 9TRS [dBm]Operator

AcceptanceBHH/Both

Antennas Active

LTE Frequency

Band

Device 1 Device 2 Device 3 Device 4 Device 5

FDD Band 5

FDD Band 7

FDD Band 8

FDD Band 1

FDD Band 2

FDD Band 3

FDD Band 4

FDD Band 11

FDD Band 12

FDD Band 13

FDD Band 17

FDD Band 18

FDD Band 19

FDD Band 20

FDD Band 21

FDD Band 25

FDD Band 26

FDD Band 28

TDD Band 38

TDD Band 39

TDD Band 40

TDD Band 41

TDD Band 42

TDD Band 43

-89,00

-89,00

-89,00

-89,00

-85,00-89,00

-85,00

-87,00

-85,00

-89,00

-89,00

-89,00

-89,00

-89,00-89,00

-85,00

-85,00

-85,00

-85,00

-85,00

-87,00

-89,00

-85,00

-85,00



V3.0 Page 14 of 14

Document Management

Document History

Version Date Brief Description of Change Approval Authority

Editor / Company

V1.0 14 May

2013 Published on GSM world TSG Katrin Jordan, DT

V2.0 Feb 2014

Updated scope, references,

requirements and added

performance values for Free

Space and Browsing.

TSG Katrin Jordan, DT

V3.0 Sept. 2015 Performance values for LTE and

Annex A added TSG

Xiaolong Zhou,

China Unicom

Abbas Alpaslan,

Vodafone

Other Information

Type Description

Document Owner This document is owned and approved by TSG Full Members

It is our intention to provide a quality product for your use. If you find any errors or omissions, please contact us with your comments. You may notify us at [email protected]. Your comments or suggestions & questions are always welcome.

mailto:[email protected]

Documents

Operator Acceptance Values for Device Antenna Performance