Options - Link-Belt Cranes · • 4th position on left console for entering and exiting the cab also serves as control lock-out • Illuminated LCD service monitor • Climate control

Operating Weight:Standard Excavator: 174,600 lbs (79 200 kg)Mass Excavator: 174,600 lbs (79 200 kg)

SAE Net Horsepower: 444 HP (331 kW)Bucket Range: 2.47 - 5.91 cu. yd. (1.89 - 4.52 cu. m.)

Lexington, KentuckyLitho in USA 6/02 #LBX2074 (Supersedes #LBX2057)

® LBX and ® Link-Belt are registered trademarks. Copyright 2002. All rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifications.

Standard Equipment

Specifications (continued)

Options• Inte-LXTM Computer System• Self-diagnostic system• Five selectable working modes• One-touch decelerator• Auto idling system• Auto idle start• Low idle up• Auto engine warm up• Auto power-up mode• Integral cylinder cushioning• Cushioned attachment control• Boom and arm holding valves• Free swing control• Auto power swing• Travel alarm• Nephron® filtration system• Low noise/low vibration cab floating

on 6 fluid filled mounts• Sliding/reclining, suspension cloth

upholstered seat with adjustable arm restsand lumbar support, retracting seat belt

• 3-position tilting consoles• 4th position on left console for entering

and exiting the cab also serves as controllock-out

• Illuminated LCD service monitor• Climate control heater and air conditioner• Hand grab rails both sides• Rear view mirrors, coat hook, storage

compartment

• Horn, interior lighting, AM/FM STEREOradio, digital clock, floor mat, cigarettelighter

• Safety glass front windows with automaticlock and intermittent rise-up windshieldwiper and washer, large LEXAN® rear/side windows

• Gate lock and gate lock lever (control lock-out device)

• Vandalism locks/guarding• Common key for cab & house doors, engine

hood, tool box, and fuel cap• Upper and lower undercovers• LC undercarriage• Easy Maintenance System (EMS)

Chrome pins and oil impregnatedbushings at all attachment locations

• 29.5" (750 mm) 2-Bar Grouser shoes• 27,560 lbs. (12 500 kg) counterweight

• Counterweight removal system(hydraulically controlled)

• Boom options27' 7" (8.40 m) Standard Excavator23' 9" (7.25 m) Mass Excavator

• Arms9' 9" (2.98 m) (Mass Excavator only)

12' 0" (3.66 m)14' 7" (4.44 m)18' 5" (5.62 m)

• Track35.5" (900 mm) 2-Bar Grouser Shoes43.3" (1100 mm) 2-Bar Grouser Shoes

• Auxiliary HydraulicsSingle ActingMulti-FunctionThumb

• Hose Burst Check Valves• Couplers (field install)

Hendrix Hydraulic CouplerEsco Multi-Pin Grabber

• Thumbs (field install)Esco Universal rigidEsco Hydraulic non-linkEsco Hydraulic non-link (for coupler)Esco Hydraulic link

Designed for Durability and Performance...Maximized OperatorComfortThe industry’s largest cab providing lownoise, climate controlled heat and airconditioning, standard. Page 3

Auto Power-UpAuto power-up automatically increasessystem pressure by 9% to power throughtough ground or when lifting a heavy load.Page 4

Cleaner Side-Wall CutsWith Auto Power-Swing, Inte-LXTM

automatically prioritizes swing torque whensimultaneously working the swing andattachment. Page 5

Low Ground Pressure andExceptional StabilityLC undercarriage for low ground pressureand stability incorporates heavy-dutyexcavator style components. Page 7

Long Life Pin and BushingDesignChrome pins and grease impregnatedbushings throughout the completeattachment hold up to torsional stressescreated in these large excavators andreduces the greasing interval. Page 7

Heavy Duty Boom andArmBuilt to handle powerful breakout forces,strong lifting capacities and the stresses ofallied attachments. Page 7

Faster Cycle TimesA smarter more efficient hydraulic systemuses dual pump flow, auto power swing andregenerative circuits for increasedproductivity. Page 5

Anti-Theft SystemTo protect your investment, a passwordprotected anti-theft system comes as standardequipment and can be activated at the userschoice. Page 4

Superior ServiceabilityOn-board diagnostics with memoryand fewer hydraulic oil changes result insuperior serviceability. Page 8

Exceptional TravelPerformanceHigh torque travel motors automatically shiftto provide increased tractive effort whenoperating in difficult ground conditions.Page 7

Smarter. Faster. Better.Inte-LXTM or Intelligent LX is the mostadvanced technology to date. Inte-LXTM

maximizes the balance between speed,power, and fuel efficiency. Page 4

First Electronic EngineControl in an ExcavatorThis results in increased responsiveness tothe job requirements; faster cycle times,increased fuel efficiency, cleaner andquieter. Page 6

Reduced Maintenance andExtended Component LifeThe Nephron® Filtration system meansless wear and tear on the hydrauliccomponents, reducing hydraulic systembreakdowns and maintenance costs.Page 8

Transportation Specifications (cont.)Catwalk

Weight:Left Front: 82 lbs. (37 kg)Left Rear: 73 lbs. (33 kg)

Dimension A: 1' 8" (.52 m)Dimension B: 8' 4" (2.55 m)Dimension C: 7' 3" (2.20 m)Dimension D: 1' 6" (.45 m)

AB C

D

Boom with Arm Cylinder and Piping

BOOM A B WIDTH WEIGHT

Excavator 7' 6" 28' 8" 4' 11" 17,725 lbs.(2.28 m) (8.73 m) (1.49 m) (8 040 kg)

Mass 8' 6" 24' 10" 4' 11" 16,578 lbs.(2.59 m) (7.58 m) (1.49 m) (7 520 kg)

A

BArm with Bucket Cylinder and Linkage

A

B

CARM A B C WIDTH WEIGHT

Mass 4' 9" 14' 5" 9' 9" 2' 5" 8,642 lbs.

9' 9" (2.98 m) arm (1.44 m) (4.40 m) (2.98 m) (.745 m) (3 920 kg)

Standard 4' 5" 17' 1" 12' 0" 2' 5" 8,223 lbs.

12' 0" (3.66 m) arm (1.35 m) (5.20 m) (3.66 m) (.745 m) (3 730 kg)

Standard 4' 3" 19' 5" 14' 7" 2' 5" 8,994 lbs.

14' 7" (4.44 m) arm (1.29 m) (5.91 m) (4.44 m) (.745 m) (4 080 kg)

Standard 4' 2" 23' 2" 18' 5" 2' 5" 10,119 lbs.

18' 5" (5.62 m) arm (1.28 m) (7.06 m) (5.62 m) (.745 m) (4 590 kg)

Boom Cylinder

A

B

C

Boom Cylinder: Weight: 1,763 lbs. (800 kg) Dimension A: 1' 3" (.40 m)Dimension B: 9' 7" (2.93 m)Dimension C: 1' 11" (.59 m)

Large, Low Noise CabDesignA wide cab design provides expandedleg and elbow room. Six silicon filledisolation mounts float the entire cababove the noise and vibration of an alreadyquiet machine greatly reducing operatorfatigue. Large entry door and access widthmakes entering and exiting the cab abreeze.

Control PanelMany machine function switches areconcentrated in a panel in clear viewand easy reach of the operator.

Tilting Console and SlidingSeatThe seat slides independently of the controlconsoles to assure optimal joystick positionsat all times.The joysticks canbe tiltedto any of threesettings,allowing theoperator to workin the mostcomfortable position. The entire platformcan then be moved forward or backward forbest foot pedal positioning.

Panoramic VisibilityThis cab provides more window spacethan ever. Even the sunroof is large. TheOperator’s “office with a view” has rear andside windows made of LEXAN®

MARGUARD™. Standard vandal coversprotect the safety glass front windowsand stow on top when you’re working.

Informative LCD MonitorLarge size LCD Monitor displays graphicallya wide range of operating information suchas; engine temperature,hydraulic oil temperature, fuel level, travelspeed, work mode and engineidle. Additional messages includesystem/machine warnings and servicedue messages in your choice of Englishand 13 other languages. Backlit illuminationensures displays are alwaysreadable – day and night.

Operator's Control Station

All Weather VisibilityWith built-in washer and intermittentspeed control, the wiper keeps yourwindshield clear, whatever the conditionoutside. The “rise-up” design takes the wiperarm and blade out of the line ofsight when its not in use, plus lifts the bladefrom the cab surface so that it doesn’t freezeto the cab in icy weather.

Fresh Air Induction-TypeClimate ControlLX provides exceptional heating/cooling ca-pabilities with a climate control system thatautomatically regulates the temperature forthe operator’s comfort. Now with 6 vents, LXSeries excavators provide exceptional aircirculation for optimum operator comfort.Front-side air outlet and defroster ensure acomfortable operating environment while theopen/closetype rear win-dow furtherimproves theventilation.

Best Seat at the SiteThe KAB 515 seat adjusts to your sizeand comfort. The semi-bucket seat providesfirm support and comfort with armrests,adjustable seat suspension, adjustablelumbar support, and durable urethanecushions.

TripmeterIn addition to the hour meter, LX has addeda Tripmeter. Every job or application canbe measured.

AM/FM Stereo RadioStandard equipment.

Emergency EscapeWindowAllows operator to escape from the rearwindow in case of emergency.

Transportation SpecificationsUpper Structure w/TTB and Lower Cross Frame

Weight: 51,370 lbs. (23 300 kg) Dimension A: 17' 6" (5.34 m)Weight: W/FOPS 52,250 lbs. (23 700 kg) Dimension B: 9' 1" (2.77 m)

Dimension C: 9' 1" (2.78 m)Dimension D: 18' 1" (5.50 m)

FOPS Head Guard:(Optional)Weight: 705 lbs. (320 kg).

A

BC

DW/FOPS

Counter Weight

A

B

C Weight: 27,557 lbs. (12 500 kg)Dimension A: 11' 5" (3.47 m)Dimension B: 4' 7" (1.39 m)Dimension C: 2' 8" (.82 m)

Total Weight: 165 lbs. (75 kg)

Dimension A: 6' 3" (1.91 m)Dimension B: 3' 1" (.94 m)Dimension C: 3' 9" (1.15 m)Dimension D: 8' 10" (2.70 m)Dimension E: 2' 0" (.60 m)Dimension F: 4' 5" (1.35 m)Dimension G: 2' 4" (.71 m)Dimension H: 5' 10" (1.77 m)Dimension I: 2' 9" (.85 m)Right Side Cab Side

Hand RailsB

A E

F

C D G H

I

Undercarriage

A BC

Shoe Width: Weight: (per side)29.5" (750 mm) 29,321 lbs. (13 300 kg)35.4" (900 mm) 30,864 lbs. (14 000 kg)43.3" (1100 mm) 32,628 lbs. (14 800 kg)Dimension A:

W/ 29.5" (750 mm) shoes - 39.7" (1 010 mm)W/ 35.4" (900 mm) shoes - 39.7" (1 010 mm)W/ 43.3" (1 100 mm) shoes - 43.3" (1 100 mm)

Dimension B: 16' 7"(5070 mm)Dimension C: 20' 10" (6360 mm)

Side Frame with Steps:

Inte-LXTM, the intelligent computer commandcontrol system monitors hydraulic output,pressures, and regulates engine perfor-mance for the maximum balance betweenspeed, power and fuel efficiency neededto handle the job.

Auto Power-UpThe LX series can quickly respond tochanges in operating conditions,automatically supplying a power increase,without operator interaction and regardlessof the work mode. Hydraulic pressuresensors detect resistance and pressure isincreased by 9% for 8 seconds. AutoPower-Up stays on 100% of the time inthe “L” mode.

Anti-Theft DeviceYour Link-Belt distributor can set up your Inte-LXTM control system to include a passwordprotection feature that requires thepassword to start and run the machine.

One-Touch and Auto IdleControlWhen user-preset time has elapsed afterleaving the control handles in the neutralposition, auto-idling automatically drops theengine to idle speed (900 rpm). Or, youcan choose to use the one-touch idlingswitch, located at the top of the rightcontroller so that you are always in control.

Inte-LXTM

Operating ModesThe LX series enables the operator to have achoice on how the machine is operated.Simply choose the work mode that matchesthe machines output to the job application.Five operating modes are available.

A: Auto-ModeThe most revolutionary approach tomaximizing power & fuel efficiencyavailable today. Just select the Auto-Modewith the switch panel. Using actual workingpressure readings, Inte-LXTM instantlychanges modes assuring the best combina-tion of speed and power while you can stayfocused on the work at hand.

H: Heavy ModeFor heavy excavation or whenever you needextra power and maximum speed.

S: Standard ModeFor standard digging and loadingoperations reducing fuel consumption.

L: Lift ModeFor lifting and other operations that needfingertip accuracy.

Allied AttachmentWork ModeAutomatically adjusts engine speed andpump output to match additional attach-ments such as hammers. The engine rpm’sare presettable to match the hydraulicrequirements.

On-Board DiagnosticsAn on-board diagnostic system allowsservice personnel to quickly analyze up to148 items in four categories;

•Machine Status: The diagnosticsystem provides a detailed view of pumppressure, engine rpm, water temperature,oil temperature, fuel temperature, throttlesetting and ongoing operating functionssuch as auto power-up and auto-mode.

•Troubleshooting: Service personnelcan trace electrical faults such as sensorfailures and harness damage.

•History: An on-going record of machinefaults is stored in the computer includingthe hour meter reading at time of the faultto assist in the diagnostics procedure.

•Systems Configuration: Servicepersonnel can change machineoperating characteristics such as; timedelay for auto-idle, language selection,and engine rpm preset for alliedattachment mode.

Arm Arm Arm

Bucket Width # 12' 0" 14' 7" 18' 5"Type Capacity Outside Lip Weight Teeth (3.66 m) (4.44 m) (5.62 m)

2.53 cu. yd. (1.93 m3) 42" (1 067 mm) 6,403 lb. (2 904 kg) 4 H H M3.00 cu. yd. (2.29 m3) 48" (1 219 mm) 6,803 lb. (3 086 kg) 4 H H M

ESCO 3.48 cu. yd. (2.66 m3) 54" (1 372 mm) 7,203 lb. (3 267 kg) 4 H M LHDP 3.96 cu. yd. (3.03 m3) 60" (1 524 mm) 7,780 lb. (3 529 kg) 5 M L N/A

4.45 cu. yd. (3.40 m3) 66" (1 676 mm) 8,180 lb. (3 710 kg) 5 M L N/A4.94 cu. yd. (3.78 m3) 72" (1 829 mm) 8,580 lb. (3 892 kg) 5 L N/A N/A5.42 cu. yd. (4.14 m3) 78" (1 981 mm) 9,157 lb. (4 154 kg) 6 L N/A N/A5.91 cu. yd. (4.52 m3) 84" (2 134 mm) 9,557 lb. (4 335 kg) 6 N/A N/A N/A

2.47 cu. yd. (1.89 m3) 45" (1 143 mm) 6,470 lb. (2 935 kg) 4 H H HESCO 3.26 cu. yd. (2.49 m3) 56" (1 422 mm) 7,211 lb. (3 271 kg) 4 H M LXDP 3.99 cu. yd. (3.05 m3) 66" (1 676 mm) 8,061 lb. (3 656 kg) 5 M L N/A

4.43 cu. yd. (3.39 m3) 72" (1 829 mm) 8,466 lb. (3 840 kg) 5 L L N/A5.30 cu. yd. (4.05 m3) 84" (2 134 mm) 9,451 lb. (4 287 kg) 6 L N/A N/A

Bucket Sizes - Standard Excavator

Approval Code ForArm/Bucket Combinations

H ........ Heavy material(up to 3,370 lbs./cu. yd.)

M ....... Medium material(up to 2,700 lbs./cu. yd.)

L ......... Light material(up to 2,020 lbs./cu. yd.)

N/A ... Not applicable

Arm

Bucket Width # 9' 9"Type Capacity Outside Lip Weight Teeth (2.98m)

2.53 cu. yd. (1.93 m3) 42" (1 067 mm) 6,403 lb. (2 904 kg) 4 H3.00 cu. yd. (2.29 m3) 48" (1 219 mm) 6,803 lb. (3 086 kg) 4 H

ESCO 3.48 cu. yd. (2.66 m3) 54" (1 372 mm) 7,203 lb. (3 267 kg) 4 HHDP 3.96 cu. yd. (3.03 m3) 60" (1 524 mm) 7,780 lb. (3 529 kg) 5 H

4.45 cu. yd. (3.40 m3) 66" (1 676 mm) 8,180 lb. (3 710 kg) 5 H4.94 cu. yd. (3.78 m3) 72" (1 829 mm) 8,580 lb. (3 892 kg) 5 H5.42 cu. yd. (4.14 m3) 78" (1 981 mm) 9,157 lb. (4 154 kg) 6 M5.91 cu. yd. (4.52 m3) 84" (2 134 mm) 9,557 lb. (4 335 kg) 6 M

2.47 cu. yd. (1.89 m3) 45" (1 143 mm) 6,470 lb. (2 935 kg) 4 HESCO 3.26 cu. yd. (2.49 m3) 56" (1 422 mm) 7,211 lb. (3 271 kg) 4 HXDP 3.99 cu. yd. (3.05 m3) 66" (1 676 mm) 8,061 lb. (3 656 kg) 5 H

4.43 cu. yd. (3.39 m3) 72" (1 829 mm) 8,466 lb. (3 840 kg) 5 H5.30 cu. yd. (4.05 m3) 84" (2 134 mm) 9,451 lb. (4 287 kg) 6 M

Bucket Sizes - Mass Excavator






Advanced HydraulicSystemTop-of-the-Class Cycle Times/FuelEfficientThe LX Series hydraulic system efficientlydelivers power, speed and control whenand where it’s needed. Fuel consumptionand cycle times are more efficient inswing/dump operations over conventionalmodels. This is accomplished throughreducing system pressure loss, re-usingreturn oil and providing double pump flowduring key operations.

Regeneration SystemBy re-using the returning oil from thearm and the boom, ground excavatingoperation speed is increased.

Two Hydraulic ReturnLinesTwo hydraulic returns lines mean fasterspeed in the system, and reduces backpressure build-up.

Performance2 Speed Boom and ArmThe 2-speed boom lifting and arm openingand closing function provides the LX serieswith top-of-its-class lifting speed especially inswing/excavating simultaneous operationssuch as truck loading.

Auto Power-SwingThis patent pending design incorporatesa selector valve that helps maintainattachment and hydraulic flow to achieveexcellent swing and digging forces in sidewall-cut operations. In normal diggingwhen side pressure is not needed, LXsends all the flow to the attachment alwaysinsuring the best performance for eitheroperation.

Cushioned SwingThis built-in special cushion valve greatlyreduces the shock and vibration at the endof each swing cycle.

Cushioned AttachmentControlIn addition to having cushioned cylinders,selectable cushioned attachment controllets you smooth out the attachmentmovements. A cushion valve in the boomand arm circuits reduce shock loading andvibration during attachment operation.

Free SwingAllows the operator to disengage the swingbrake providing crane-like precision andcontrol when handling loads.

Single Pedal TravelAllows the operator to engage both tracks atthe same time using only one pedal. Thiskeeps the machine in line with the ditch andprovides safety and ease in loading/unloading the machine for transport.

Automatic Speed ShiftingWhen operating in difficult travelconditions, the travel motor automaticallydownshifts from high to low speed forincreased tractive effort and thenautomatically returns to high speedwhen travel conditions permit.

Fuel Tank CapacityThe LX Series fuel tank provides thecapacity to reduce refueling frequency,allowing for an extended work day.

Lifting Capacities (Mass Excavator) w/side frames extended

1. Lifting capacities shown should not beexceeded. Weight of all lifting accessoriesmust be deducted from the above liftingcapacities.

2. Lifting capacities are based on machinestanding on firm, uniform supporting surface.User must make allowances for job conditionssuch as soft or uneven ground.

3. Lifting capacities shown do not exceed 75% ofminimum tipping loads or 87% of hydrauliccapacities. Capacities marked with an asterisk (*)are limited by hydraulic capacities.

4. Least stable position is over the side.5. Operator should be fully acquainted

with the Operator’s Manual & Operating SafetyBooklet, furnished by LBX before operating themachine.

6. Capacities apply only to the machine asoriginally manufactured and normallyequipped by LBX Company, LLC.

7. Lift capacity ratings are based on SAEJ/ISO 10567, “Earthmoving Machinery– Hydraulic Excavators – Lift Capacity”.

8. Lifting or digging operations with theside frames in the retracted positionsare not permitted.

Notes: Excavator lifting capacities

9' 9" (2.98 m) Armwith 23' 9" (7.25 m) Boom and 7,625 lb. (3 458 kg) Bucket.Auto Power-Up Mode Applied

18' 5" (5.62 m) Arm w/side frames extendedwith 27' 7" (8.40 m) Boom and 5,710 lb. (2 590 kg) Bucket.Auto Power-Up Mode Applied

Radius of Load

10' 0" (3.05 m) 15' 0" (4.57 m) 20' 0" (6.10 m) 25' 0" (7.62 m) 30' 0" (9.14 m) 35' 0" (10.66 m) 40' 0" (12.19 m) 45' 0" (13.71 m) Cap. at Max. Reach

End Side End Side End Side End Side End Side End Side End Side End Side End Side

+35' 0" lbs.(10.66 m) kg

+30' 0" lbs.(9.14 m) kg

+25' 0" lbs.(7.62 m) kg

+20' 0" lbs.(6.10 m) kg+15' 0" lbs.(4.57 m) kg+10' 0" lbs.(3.05 m) kg+5' 0" lbs.

(1.52 m) kgGround lbs.

Line kg-5' 0" lbs.

(1.52 m) kg-10' 0" lbs.(3.05 m) kg-15' 0" lbs.(4.57 m) kg-20' 0" lbs.(6.10 m) kg-25' 0" lbs.(7.62 m) kg

BucketHookHeight

11,800* 11,800*5 350* 5 350*

18,650* 18,650* 10,800* 10,800*8 450* 8 450* 4 890* 4 890*22,350* 22,350* 12,000* 12,000* 10,200* 10,200*10 130* 10 130* 5 440* 5 440* 4 620* 4 620*23,450* 22,050 17,550* 16,700* 9,950* 9,950*10 630* 10 000 7 960* 7 570* 4 510* 4 510*

32,600* 32,600* 28,000* 27,700 25,000* 20,750 21,400* 15,850 10,050* 10,050*14 780* 14 780* 12 700* 12 560 11 330* 9 410 9 700* 7 180 4 550* 4 550*

72,400* 72,400* 48,900* 48,900* 37,500* 35,250 30,950* 25,800 26,800* 19,500 24,050* 15,050 10,350* 10,350*32 840* 32 840* 22 180* 22 180* 17 000* 15 980 14 030* 11 700 12 150* 8 840 10 900* 6 820 4 690* 4 690*48,250* 48,250* 55,750* 47,100 41,800* 32,750 33,650* 24,150 28,500* 18,350 24,950* 14,250 11,050* 11,050*21 880* 21 880* 25 280* 21 360 18 960* 14 850 15 260* 10 950 12 920* 8 320 11 310* 6 460 5 010* 5 010*48,200* 48,200* 59,700* 44,700 44,800* 30,950 35,700* 22,850 29,750* 17,450 24,550 13,650 12,200* 12,200*21 860* 21 860* 27 070* 20 270 20 320* 14 030 16 190* 10 360 13 490* 7 910 11 130 6 190 5 530* 5 530*57,050* 57,050* 60,750* 43,400 46,150* 29,800 36,700* 21,950 30,050 16,800 22,550* 13,300 13,950* 12,70025 870* 25 870* 27 550* 19 680 20 930* 13 510 16 640* 9 950 13 630 7 620 10 220* 6 030 6 320* 5 76070,900* 70,900* 59,250* 42,900 45,600* 29,250 36,300* 21,500 29,500* 16,550 16,750* 13,85032 160* 32 160* 26 870* 19 450 20 680* 13 260 16 460* 9 750 13 380* 7 500 7 590* 6 280

62,850* 62,850* 73,250* 73,150 55,100* 43,050 42,900* 29,250 34,050* 21,500 26,800* 16,750 21,550* 15,95028 500* 28 500* 33 220* 33 180 24 990* 19 520 19 450* 13 260 15 440* 9 750 12 150* 7 590 9 770* 7 23082,000* 82,000* 62,300* 62,300* 47,850* 43,750 37,350* 29,800 28,750* 22,100 25,100* 19,90037 190* 37 190* 28 250* 28 250* 21 700* 19 840 16 940* 13 510 13 040* 10 020 11 380* 9 020

45,950* 45,950 * 35,750* 35,750* 26,700* 26,700* 23,550* 23,550*20 840* 20 840* 16 210* 16 210* 12 110* 12 110* 10 680* 10 680*

Radius of Load

10' 0" (3.05 m) 15' 0" (4.57 m) 20' 0" (6.10 m) 25' 0" (7.62 m) 30' 0" (9.14 m) Cap. at Max. Reach

End Side End Side End Side End Side End Side End Side

+30' 0" lbs.(9.14 m) kg

+25' 0" lbs.(7.62 m) kg



Line kg-5' 0" lbs.

(1.52 m) kg-10' 0" lbs.(3.05 m) kg-15' 0" lbs.(4.57 m) kg

26,500* 26,500*12 020* 12 020*26,200* 26,200*11 880* 11 880*

38,730* 38,730* 34,920* 30,420 26,900* 26,900*17 560* 17 560* 15 830* 13 790 12 200* 12 200*

70,980* 70,980* 52,030* 52,030* 42,420* 39,980 36,730* 29,150 28,510* 24,11032 190* 32 190* 23 600* 23 600* 19 240* 18 130 16 660* 13 220 12 930* 10 93084,560* 84,560* 58,950* 53,500 46,210* 37,520 38,720* 27,760 31,200* 22,57038 350* 38 350* 26 730* 24 260 20 960* 17 010 17 560* 12 590 14 150* 10 23068,440* 68,440* 63,610* 50,140 49,100* 35,470 40,250* 26,540 35,430* 22,08031 040* 31 040* 28 850* 22 740 22 270* 16 080 18 250* 12 030 16 070* 10 01077,680* 77,680* 64,970* 48,260 50,270* 34,120 40,620* 25,700 36,740* 22,66035 230* 35 230* 29 470* 21 890 22 800* 15 470 18 420* 11 650 16 660* 10 270

59,110* 59,110* 83,320* 78,050 62,930* 47,610 49,070* 33,520 38,970* 25,400 37,790* 24,62026 810* 26 810* 37 790* 35 400 28 540* 21 590 22 250* 15 200 17 670* 11 520 17 140* 11 16084,380* 84,380* 73,900* 73,900* 57,200* 47,950 44,590* 33,730 38,550* 28,90038 270* 38 270* 33 520* 33 520* 25 940* 21 740 20 220* 15 290 17 480* 13 100

58,970* 58,970* 46,220* 46,220* 38,060* 38,060*26 740* 26 740* 20 960* 20 960* 17 260* 17 260*

BucketHookHeight

Lifting Capacities (Standard Excavator) w/sideframes extended (cont.)


Dependable Isuzu PowerAuto Engine Warm-UpIf the engine temperature is low followingstart-up, the auto warm-up system willoperate automatically and continue withengine speed increasing gradually untilnormal engine operating temperaturesare reached.

Air FiltrationLX Series engines are equipped with a dualelement air filter with an evacuator cup andrestriction indicator for ease of maintenance.

Larger MufflerThe LX series features a larger muffler whichabsorbs more sound and makes this thequietest Link-Belt yet.

Emergency EngineShutdownIn emergency situations, the engine can beshut down with the push of a switch locatedon the control panel in the cab. This switchmust be re-engaged prior to restarting theengine.

Engine Product SupportIsuzu North America offers 24-hour accessto their full line of engine parts through 2regional distribution centers, 27 MasterDistributors and 690 Authorized ServiceDealers.

Maintaining engine revolution at a fixed rateregardless of the load prevents the energy loss thatoccurs when shifting cycle times to accommodatehigher or lower loads.

Advantages of EEC

Tier II CompliantLX engines meet EPA Tier II standardsrequirements.

Idle StartAt start-up, the engine defaults to idleregardless of throttle position. This preventsover revving a cold engine, helping toextend its service life.

Low Idle UpWhen low temperatures or other conditionsreduce engine rpm to a point thatalternator output won’t keep the batterycharged, Inte-LXTM automatically increasesthe idle speed from 900 to 1100 rpmkeeping the batteries fully charged.

First In ClassThe 800 LX is the first excavator in it’s classto utilize an electronic engine controlfunction. By optimizing the level of fuelinjection to match the load, this responsivenew system assures more efficient use offuel, plus by keeping the engine closer tothe target engine speed, less lugging takesplace so cycle times are faster, exhaustnoise, vibration, and smoke are reducedmaking the environment in the cab andaround the machine cleaner and quieter.

Electronic Engine Control(EEC)Inte-LXTM maintains engine rpm’s when loaddemands change. Engines equipped withmechanical governors spike rpm’s up-and-down when operating loads increase anddecrease. This phenomena causes enginesto consume extra fuel and be louder.

Low Fuel ConsumptionThe electronic governor responds tochanges in operating loads quicker thana mechanical governor. As a result, EECregulates the amount of fuel injectionaccurately and quickly.

Lower, Cleaner EmissionsLow fuel consumption results in high ignitionefficiency (cleaner emission) and lowemissions.

Low Sound LevelsAt high idle, EEC can control enginespeed rpm at rated horsepower. Thismeans the engine doesn’t overrun,resulting in lower sound levels.

Low VibrationEEC causes engine rpm to be stable,resulting in low vibration.

Lifting Capacities (Standard Excavator) w/sideframes extended

14' 7" (4.44 m) Arm w/side frames extendedwith 27' 7" (8.40 m) Boomand 6,614 lb. (3 000 kg) Bucket. Auto Power-Up Mode Applied


Radius of Load

10' 0" (3.05 m) 15' 0" (4.57 m) 20' 0" (6.10 m) 25' 0" (7.62 m) 30' 0" (9.14 m) 35' 0" (10.66 m) Cap. at Max. Reach

End Side End Side End Side End Side End Side End Side End Side

+30' 0" lbs.(9.14 m) kg

+25' 0" lbs.(7.62 m) kg



Line kg-5' 0" lbs.

(1.52 m) kg-10' 0" lbs.(3.05 m) kg-15' 0" lbs.(4.57 m) kg-20' 0" lbs.(6.10 m) kg

BucketHookHeight

16,420* 16,420*7 440* 7 440*

28,540* 28,540* 22,530* 22,530* 16,360* 16,360*12 940* 12 940* 10 210* 10 210* 7 420* 7 420*30,570* 30,570* 27,850* 23,200 16,760* 16,760*13 860* 13 860* 12 630* 10 520 7 600* 7 600*

70,910* 70,910* 49,460* 49,460* 39,130* 39,130* 33,110* 29,170 29,270* 22,190 17,610* 17,610*32 160* 32 160* 22 430* 22 430* 17 740* 17 740* 15 010* 13 230 13 270* 10 060 7 980* 7 980*

56,720* 51,580 43,390* 36,700 35,700* 27,460 30,790* 21,140 18,950* 16,67025 720* 23 390 19 680* 16 640 16 190* 12 450 13 960* 9 580 8 590* 7 560

36,340* 36,340* 61,470* 48,140 46,710* 34,430 37,860* 25,980 32,070* 20,190 20,970* 16,28016 480* 16 480* 27 880* 21 830 21 180* 15 610 17 170* 11 780 14 540* 9 150 9 510* 7 38046,410* 46,410* 63,190* 46,310 48,540* 32,910 39,170* 24,890 32,760* 19,480 23,970* 16,48021 050* 21 050* 28 660* 21 000 22 010* 14 920 17 760* 11 290 14 850* 8 830 10 870* 7 470

40,280* 40,280* 60,960* 60,960* 62,310* 45,610 48,630* 32,120 39,280* 24,260 32,430* 19,090 28,600* 17,38018 270* 18 270* 27 650* 27 650* 28 260* 20 680 22 050* 14 560 17 810* 11 000 14 710* 8 650 12 970* 7 88056,710* 56,710* 76,290* 75,780 59,090* 45,700 46,790* 31,970 37,780* 24,130 30,680* 19,28025 720* 25 720* 34 600* 34 370 26 800* 20 720 21 220* 14 500 17 130* 10 940 13 910* 8 74074,790* 74,790* 67,350* 67,350* 53,240* 46,470 42,520* 32,430 33,810* 24,580 31,260* 22,88033 920* 33 920* 30 540* 30 540* 24 140* 21 070 19 280* 14 710 15 330* 11 140 14 170* 10 370

54,210* 54,210* 43,640* 43,640* 34,380* 33,680 30,920* 30,27024 580* 24 580* 19 790* 19 790* 15 590* 15 270 14 020* 13 730

Radius of Load10' 0" (3.05 m) 15' 0" (4.57 m) 20' 0" (6.10 m) 25' 0" (7.62 m) 30' 0" (9.14 m) 35' 0" (10.66 m) 40' 0" (12.19 m) Cap. at Max. Reach

End Side End Side End Side End Side End Side End Side End Side End Side

+35' 0" lbs.(10.66 m) kg

+30' 0" lbs.(9.14 m) kg

+25' 0" lbs.(7.62 m) kg



Line kg-5' 0" lbs.


BucketHookHeight

10,980* 10,980*4 980* 4 980*

16,730* 16,730* 9,690* 9,690*7 580* 7 580* 4 390* 4 390*22,150* 22,150* 9,480* 9,480*10 040* 10 040* 4 300* 4 300*

27,850* 27,850* 25,520* 23,460 15,440* 15,440* 9,550* 9,550*12 630* 12 630* 11 570* 10 640 7 000* 7 000* 4 330* 4 330*

35,820* 35,820* 30,590* 29,590 27,160* 22,340 20,150* 17,110 9,880* 9,880*16 240* 16 240* 13 870* 13 420 12 310* 10 130 9 130* 7 760 4 480* 4 480*

64,210* 64,210* 52,440* 52,440* 40,470* 37,410 33,470* 27,720 28,940* 21,150 23,750* 16,390 10,490* 10,490*29 120* 29 120* 23 780* 23 780* 18 350* 16 960 15 180* 12 570 13 120* 9 590 10 770* 7 430 4 750* 4 750*42,980* 42,980* 58,500* 49,040 44,420* 34,790 36,030* 26,030 30,550* 20,060 25,990* 15,710 11,430* 11,430*19 490* 19 490* 26 530* 22 240 20 140* 15 780 16 340* 11 800 13 850* 9 090 11 780* 7 120 5 180* 5 180*

21,790* 21,790* 45,120* 45,120* 61,750* 46,450 47,040* 32,900 37,860* 24,710 31,680* 19,170 25,240* 15,170 12,830* 12,830*9 880* 9 880* 20 460* 20 460* 28 000* 21 060 21 330* 14 920 17 170* 11 200 14 360* 8 690 11 440* 6 880 5 810* 5 810*33,900* 33,900* 54,210* 54,210* 62,310* 45,170 48,040* 31,750 38,640* 23,850 31,930 18,590 18,450* 14,890 14,910* 14,63015 370* 15 370* 24 580* 24 580* 28 260* 20 480 21 790* 14 400 17 520* 10 810 14 480 8 430 8 360* 6 750 6 760* 6 63046,540* 46,540* 67,370* 67,370* 60,450* 44,820 47,230* 31,280 38,020* 23,460 31,100* 18,380 18,130* 15,99021 110* 21 110* 30 550* 30 550* 27 410* 20 330 21 420* 14 180 17 240* 10 640 14 100* 8 330 8 220* 7 25060,780* 60,780* 73,090* 73,090* 56,090* 45,220 44,290* 31,420 35,490* 23,580 27,380* 18,680 23,580* 18,46027 560* 27 560* 33 150* 33 150* 25 440* 20 510 20 080* 14 250 16 090* 10 690 12 410* 8 470 10 690* 8 37077,890* 77,890* 62,060* 62,060* 48,560* 46,350 38,380* 32,240 29,680* 24,400 27,470* 23,04035 330* 35 330* 28 150* 28 150* 22 020* 21 020 17 400* 14 620 13 460* 11 060 12 460* 10 450

45,460* 45,460* 35,960* 35,960* 26,870* 26,870* 25,810* 25,810*20 620* 20 620* 16 310* 16 310* 12 180* 12 180* 11 700* 11 700*

Dimensions


Working Ranges

Mass Excavator

Machine equipped with 9' 9" Arm23' 9" (7.25 m) boom. (2.98 m)

A Max. digging radius 40' 5"(12.31 m)

B Max. digging radius 39' 4"@ ground level (11.99 m)

C Max. digging depth 23' 1"(7.03 m)

D Max. digging height 38' 7"(11.76 m)

E Max. dumping height 25' 11"(7.89 m)

F Digging depth – 8' 22' 7"(2.44 m) level bottom (6.88 m)

G Bucket wrist angle 162°

H Max. vertical wall depth 13' 11"(4.25 m)

Machine equipped with:

1

2 4

3Mass Excavator -9' 9" (2.98 m) arm

12' 0" (3.66 m) arm

2 3 41

Extended Side rails

Machine equipped with 12' 0" Arm 14' 7" 18' 5"27' 7" (8.40 m) boom. (3.66 m) (4.44 m) (5.62 m)

A Max. digging radius 46' 4" 49' 0" 52' 10"(14.12 m) (14.94 m) (16.11 m)

B Max. digging radius 45' 5" 48' 2" 52' 0"@ ground level (13.84 m) (14.68 m) (15.86 m)

C Max. digging depth 28' 6" 31' 1" 35' 0"(8.69 m) (9.47 m) (10.66 m)

D Max. digging height 42' 4" 44' 7" 46' 11"(12.91 m) (13.60 m) (14.66 m)

E Max. dumping height 29' 3" 31' 2" 33' 4"(8.92 m) (9.51 m) (10.17 m)

F Digging depth – 8' 28' 1" 30' 9" 34' 8"(2.44 m) level bottom (8.57 m) (9.36 m) (10.56 m)

G Bucket wrist angle 167° 167° 167°

H Max. vertical wall depth 21' 2" 25' 5" 29' 11"(6.44 m) (7.75 m) (9.11 m)

Standard Excavator

46' 5"(14.14 m)

42' 8"(13.01 m)

46' 3"(14.10 m)

45' 0"(13.71 m)

11' 9" (3.58 m)

14' 7" (4.44 m) arm

18' 5" (5.62 m) arm

16' 7" (5.05 m)

15' 9" (4.81 m)

16' 5" (5.0 m)

20' 3" (6.17 m)

20' 10" (6.36 m) 9' 3" (2.83 m)

2' 11"(.89 m)

5' 3"(1.59 m)

12' 3" (3.74 m)

2' 6" (750 mm)

12' 5

"(3

.79

m)

3' 3"(1.0 m)

6' 11"(2.12 m)

6' 7"(2.01 m)

13' 7"(2.12 m)

16' 8" (5.07 m)

13' 4" (4.07 m)

Powerful Breakout ForcesDeep and wide box sections of highyield steel and deep groove welding holdup to high breakout forces, strong liftingcapacities and the stresses of alliedattachments such as hammers,thumbs, compactors, shears, grapplesand crushers.

Strength and DurabilityLX heavy duty booms and arms haveinternal baffles which provide betterstrength and durability to withstandtorsional loads.

LC UndercarriageLong undercarriages incorporate heavy dutyexcavator style components and improveboth stability and ground bearing pressure.The 800 LX is designed with expandable/retractable side frames for ease of transport.High torque compact final drives keep yougoing up steep grades and through deepmud.

Bearing Tub

Built into the carbody is the turntablebearing “tub” which extends down throughthe top plate and is welded to the bottom ofthe carbody as well as the top for increasedstrength and durability.

Upper and Attachments

Undercarriage

Easy Maintenance SystemChrome plated pins mounted in greaseimpregnated brass bushings on completeattachment make a durable and long

lasting connection. This also makes itpossible to extend the lubrication interval onthis type of pin to once every 6 months or1,000 hours of operation, whichever comesfirst.

A. The surface of the bushing is stratifiedwith a solid lubricant in hard brass toprotect the parts from abrasion.

B. The pin’s surface is plate-processed toincrease hardness and protect fromabrasion

C. The original dust seal is double-structuredto keep out dust and dirt and protect fromsubsequent abrasion.

Three Arm Choices (standard excavator)and a wide variety of buckets provide thereach and breakout forces for optimumproductivity.

Mass Excavator attachment is alsoavailable.

Two-Speed Travel MotorOffers smooth shifting and the needed pullwhen going up grades and making turns.

Strut Type Chain LinksThere are no weak links in our chain. Strutsreduce twisting and hold up to severe pointloading when all of the machine weight istransferred through one roller. Track pins aregreased and sealed for long life.

Track RollersFilled with synthetic oil to reduce heatbuild up and for long term reliability.

Track AdjustmentAdjustments are made easy with standardgrease cylinder track adjusters and shockabsorbing springs.

Side FramesSide frames expand/retract : use inexpanded position only to dig, retractedposition to transport.

1

2

3

4

Nephron® FiltrationExtends the Service Life ofthe Hydraulic SystemThe Nephron® Filtration System eliminatescontaminants of 1 micron or more in size.This significantly reduces hydraulic systembreakdown and maintenance costs undernormal usage. Less wear and tear on thehydraulic components means more yearsof reliable performance.

Nephron® FilterAdvantages1.Problems associated with hydraulic system

contamination are substantially reduced.Machine down time and costs forrepairing are saved as a consequence.

2.The interval of hydraulic oil replacement isextended to every 5000 hours.

3.The wear of hydraulic components isreduced, which lengthens the service lifeof the machine.

Reliability/Serviceability

Large wide openingaccess doorsThese doors make it easy to get to all routinemaintenance locations.

Hydraulic Fittings“O” ring seals are used as hydraulicconnectors to assure tighter seals.

Air Conditioner Air IntakeFilterThis filter lets in fresh clean air and ismounted on the outside of the cab, enablingeasy cleaning and replacement.

Sealed Automotive StyleWiring HarnessThese harnesses are sealed to eliminatedirt and moisture that can cause a circuitto short out. Wiring is also color andnumber coded to make trouble shootingfaster and easier.

Exceptional Customer/Product SupportYour investment in the Link-Belt LX SeriesExcavator is always protected. LBXDistribution is located from coast to coast;you’re never far from quality serviceprofessionals. “Level Two” support takesthe form of experienced factory serviceadvisors, on-call at a moment’s notice.And to expedite parts, LBX utilizes theproven parts system LINK-NET…an on-line,around the clock parts distribution solution.You can be assured that we have theparts when you need them.

This chart shows the LX machine with the Nephron® filter vs. most other excavators. As you cansee hydraulic fluid changes are reduced from every 2,000 hours to every 5,000 hours. Also,22 filter changes on a typical excavator is reduced to 7 filter changes. All of this results in lowerlabor, downtime, and maintenance costs.

Inte-LXTM On-BoardDiagnosticsInte-LXTM monitors, stores, and displaysinformation about the electrical andhydraulic systems such as; the currentmachine conditions, diagnostic warnings,history, and machine default settings.Information stored in Inte-LXTM can also bedownloaded to your personal computerusing standard connectors .

SpecificationsCab and Controls

Cab mounted on 6 fluid filled mountings.Features include a safety glass front window andLEXAN® MARGARDTM rear and side windows,reclining/sliding suspension seat with headrest,armrests, lumbar support, heater, air conditioner,AM/FM stereo, cigarette lighter, pop-up skylightwindow, and intermittent wiper with washer.Front window slides upward for storage and thelower front window is removable. Control leversare located in 3-position tilting control consoles.Reliable soft-touch switches. Easy-to-readilluminated LCD service monitor keeps operator intouch with critical machine functions.

Heater output ........... 20,240 BTU/hr (5 100 kcal/hr)A/C output .............. 18,250 BTU/hr (4 600 kcal/hr)Noise level (inside cab) ............................... 79 dB(A)Noise level (exterior) ................................. 110 dB(A)

Swing

Planetary reduction powered by axial pistonmotor. Internal ring gear with grease cavity forswing pinion. Swing bearing is single-row sheartype ball bearing. Swing cushion valve and dualstage relief valves for smooth swing decelerationand stops. Mechanical disc swing brake. Autopower swing.

Swing speed .......................................... 0 – 7.6 rpmTail swing ......................................... 13' 5" (4.10 m)Swing torque ............. 177,750 ft.-lbs. (24 580 kgf-m)

Undercarriage

Carbody is integrally welded for strength anddurability. LC undercarriage side frames areexpandable and retractable, equipped withgrease cylinder track adjusters and shockabsorbing springs, sealed track, lubricated rollersand idlers. Two-bar grouser track shoes.

Carrier rollers ........................................... 3 per sideTrack rollers .............................................. 9 per sideTrack link pitch ................................. 10.3" (260 mm)Shoes ..................................................... 51 per sideShoe width ...................................... 29.5" (750 mm)Ground pressurew/29.5" (750 mm) shoes ....... 13.00 psi (.96 kg/cm2)w/35.5" (900 mm) shoes ....... 11.33 psi (.80 kg/cm2)w/43.3" (1 100 mm) shoes ....... 9.27 psi (.65 kg/cm2)

Travel System

Two-speed independent hydrostatic travel withcompact axial piston motors for increasedperformance. Hydraulic motor powered outputshaft coupled to a planetary reduction unit andtrack sprocket. All hydraulic componentsmounted within the width of side frame.

Automatic Downshift: When operating in difficulttravel conditions, the travel motor automatically

Engine

Isuzu BB-6WG1XQB Electric engine control,water cooled, 4-cycle diesel, 6 cylinder,turbocharged with air cooled intercooler, 957 CID(15 682 cc), 5.79" (147 mm) bore x 6.06" (154mm) stroke. EPA Tier II compliant.

SAE net horsepower .. 444 HP (331 kW) @ 1,800 rpmMax. torque ..... 1,410 ft-lbs. (1,912 N-m) @ 1,500 rpmStarter .................................................. Electric, 24VAlternator ................................................... 90 ampBattery Cold Cranking ........................... 1,146 ampsAir cleaner ....................................... Double elementGovernor ................................................. ElectronicFuel Usage*

Heavy - ............................... 18.5 gph (70.0 l/hr)Average - ............................ 15.4 gph (58.3 l/hr)Light - ................................. 12.3 gph (46.6 l/hr)

*Fuel economy varies widely depending upon application.

The "Heavy" category represents nearly continuous operation intough digging applications. The "Light" category representsapplications that utilize the machine about 50% of the time, in

easier digging.

Hydraulic System

Two variable displacement axial piston pumpsand one gear pump for pilot controls, withLink-Belt Inte-LXTM Control System. Link-Belt Inte-LXTM Control includes: electric engine control, fiveselectable working modes, automatic power-up,auto/one touch idling, automatic speed shifting,free swing, cushioned attachment, swing anti-braking system, and two safety lockout switchesincluding gate lock.

Hydraulic PumpsTwo variable volume piston pumps provide powerfor attachment, swing and travel.

Maximum flow .......... 2 x 132.1 gpm (2 x 500 l/min)Pilot pump max. flow ................... 7.1 gpm (27 l/min)

Relief Valve SettingsBoom/arm/bucket ................ 4,550 psi (320 kg/cm2) in Power-Up Mode ......... 4,970 psi (350 kg/cm2)Swing circuit ......................... 4,050 psi (285 kg/cm2)Travel ................................... 4,970 psi (350 kg/cm2)

Hydraulic Cylinders – number of cylinders – borex rod x stroke.

Boom .................................... 2 – 7.9" x 5.5" x 74.5"(200 mm x 140 mm x 1 893 mm)

Arm ...................................... 1 – 8.5" x 5.9" x 85.6"(215 mm x 150 mm x 2 175 mm)

Excavator Bucket .................... 1 – 7.5" x 5.1" x 61.2"(190 mm x 130 mm x 1 555 mm)

Oil Filtration

Nephron® filter .......................................... 1 micronReturn, pilot ............................................. 10 micronSuction filter ........................................... 105 micron

Control Valve One 4-spool valve and one 5-spoolvalve with auxiliary spool.

downshifts from high to low speed for increasedtractive effort and then automatically returns tohigh speed when travel conditions permit.

Max. travel speed ........ 1.8/2.7 mph (2.9/4.3 km/h)Traction force .................... 122,300 lbs. (55 465 kgf)Gradeability ..................................................... 70%

Spring applied, hydraulically released discparking brake built into each motor. Each travelmotor equipped with counterbalance valve toprevent overspeeding down an incline and3-stage reliefs for smooth starts and stops.

Lubricant andCoolant CapacityHydraulic tank ............................. 82 gal. (310 liters)Hydraulic system ........................ 190 gal. (720 liters)Final drive (per side) ................... 3.6 gal. (13.5 liters)Swing drive ............................... 3.6 gal. (13.5 liters)Engine ....................................... 12.4 gal. (47 liters)Fuel tank ................................... 238 gal. (900 liters)Cooling system ......................... 26.4 gal. (100 liters)

AttachmentBoom (Standard excavator) ................. 27' 7" (8.4 m)

Available Arms Digging Force*• 12' 0" (3.66 m) ............... 61,600 lbs. (27 940 kgf)

in Auto Power-Up Mode .. 67,440 lbs. (30 590 kgf)

• 14' 7" (4.44 m) ............... 52,160 lbs. (23 660 kgf)in Auto Power-Up Mode . 56,880 lbs. (25 800 kgf)

• 18' 5" (5.62 m) ............... 45,410 lbs. (20 598 kgf)in Auto Power-Up Mode .. 49,680 lbs. (22 534 kgf)

Boom (Mass excavator) ..................... 23' 9" (7.25 m)

Available Arms Digging Force*• 9' 9" (2.98 m) (Mass) ........ 71,260 lbs. (32 320 kgf)

in Auto Power-Up Mode . 78,010 lbs. (35 380 kgf)

Standard ExcavatorBucket Digging Force ....... 74,190 lbs. (33 650 kgf)in Auto Power-Up Mode ..... 81,160 lbs. (36 810 kgf)

Mass ExcavatorBucket Digging Force ....... 96,670 lbs. (43 850 kgf)in Auto Power-Up Mode ... 105,660 lbs. (47 930 kgf)

*Digging force ratings are based on ISO 6015, “EarthmovingMachinery – Hydraulic Excavators – Tool Forces”.

Operating Weight

Standard Excavator - Working weight with29.5" (750 mm) shoes, 27' 7" (8.40 m) boom,12' 0" (3.66 m) arm, 6,610 lb. (3 000 kg) bucketand 27,560 lbs. (12 500 kg) counterweight ....................................... 174,600 lbs. (79 200 kg)

Mass Excavator - Working weight with 29.5"(750 mm) shoes, 23' 9" (7.25 m) boom, 9' 9"(2.98 m) arm, 7,630 lb. (3 460 kg) bucket and27,560 lbs. (12 500 kg) counterweight .............................................. 174,600 lbs. (79 200 kg)

Nephron® FiltrationExtends the Service Life ofthe Hydraulic SystemThe Nephron® Filtration System eliminatescontaminants of 1 micron or more in size.This significantly reduces hydraulic systembreakdown and maintenance costs undernormal usage. Less wear and tear on thehydraulic components means more yearsof reliable performance.

Nephron® FilterAdvantages1.Problems associated with hydraulic system

contamination are substantially reduced.Machine down time and costs forrepairing are saved as a consequence.

2.The interval of hydraulic oil replacement isextended to every 5000 hours.

3.The wear of hydraulic components isreduced, which lengthens the service lifeof the machine.

Reliability/Serviceability

Large wide openingaccess doorsThese doors make it easy to get to all routinemaintenance locations.

Hydraulic Fittings“O” ring seals are used as hydraulicconnectors to assure tighter seals.

Air Conditioner Air IntakeFilterThis filter lets in fresh clean air and ismounted on the outside of the cab, enablingeasy cleaning and replacement.

Sealed Automotive StyleWiring HarnessThese harnesses are sealed to eliminatedirt and moisture that can cause a circuitto short out. Wiring is also color andnumber coded to make trouble shootingfaster and easier.

Exceptional Customer/Product SupportYour investment in the Link-Belt LX SeriesExcavator is always protected. LBXDistribution is located from coast to coast;you’re never far from quality serviceprofessionals. “Level Two” support takesthe form of experienced factory serviceadvisors, on-call at a moment’s notice.And to expedite parts, LBX utilizes theproven parts system LINK-NET…an on-line,around the clock parts distribution solution.You can be assured that we have theparts when you need them.

This chart shows the LX machine with the Nephron® filter vs. most other excavators. As you cansee hydraulic fluid changes are reduced from every 2,000 hours to every 5,000 hours. Also,22 filter changes on a typical excavator is reduced to 7 filter changes. All of this results in lowerlabor, downtime, and maintenance costs.

Inte-LXTM On-BoardDiagnosticsInte-LXTM monitors, stores, and displaysinformation about the electrical andhydraulic systems such as; the currentmachine conditions, diagnostic warnings,history, and machine default settings.Information stored in Inte-LXTM can also bedownloaded to your personal computerusing standard connectors .

SpecificationsCab and Controls

Cab mounted on 6 fluid filled mountings.Features include a safety glass front window andLEXAN® MARGARDTM rear and side windows,reclining/sliding suspension seat with headrest,armrests, lumbar support, heater, air conditioner,AM/FM stereo, cigarette lighter, pop-up skylightwindow, and intermittent wiper with washer.Front window slides upward for storage and thelower front window is removable. Control leversare located in 3-position tilting control consoles.Reliable soft-touch switches. Easy-to-readilluminated LCD service monitor keeps operator intouch with critical machine functions.

Heater output ........... 20,240 BTU/hr (5 100 kcal/hr)A/C output .............. 18,250 BTU/hr (4 600 kcal/hr)Noise level (inside cab) ............................... 79 dB(A)Noise level (exterior) ................................. 110 dB(A)

Swing

Planetary reduction powered by axial pistonmotor. Internal ring gear with grease cavity forswing pinion. Swing bearing is single-row sheartype ball bearing. Swing cushion valve and dualstage relief valves for smooth swing decelerationand stops. Mechanical disc swing brake. Autopower swing.

Swing speed .......................................... 0 – 7.6 rpmTail swing ......................................... 13' 5" (4.10 m)Swing torque ............. 177,750 ft.-lbs. (24 580 kgf-m)

Undercarriage

Carbody is integrally welded for strength anddurability. LC undercarriage side frames areexpandable and retractable, equipped withgrease cylinder track adjusters and shockabsorbing springs, sealed track, lubricated rollersand idlers. Two-bar grouser track shoes.

Carrier rollers ........................................... 3 per sideTrack rollers .............................................. 9 per sideTrack link pitch ................................. 10.3" (260 mm)Shoes ..................................................... 51 per sideShoe width ...................................... 29.5" (750 mm)Ground pressurew/29.5" (750 mm) shoes ....... 13.00 psi (.96 kg/cm2)w/35.5" (900 mm) shoes ....... 11.33 psi (.80 kg/cm2)w/43.3" (1 100 mm) shoes ....... 9.27 psi (.65 kg/cm2)

Travel System

Two-speed independent hydrostatic travel withcompact axial piston motors for increasedperformance. Hydraulic motor powered outputshaft coupled to a planetary reduction unit andtrack sprocket. All hydraulic componentsmounted within the width of side frame.

Automatic Downshift: When operating in difficulttravel conditions, the travel motor automatically

Engine

Isuzu BB-6WG1XQB Electric engine control,water cooled, 4-cycle diesel, 6 cylinder,turbocharged with air cooled intercooler, 957 CID(15 682 cc), 5.79" (147 mm) bore x 6.06" (154mm) stroke. EPA Tier II compliant.

SAE net horsepower .. 444 HP (331 kW) @ 1,800 rpmMax. torque ..... 1,410 ft-lbs. (1,912 N-m) @ 1,500 rpmStarter .................................................. Electric, 24VAlternator ................................................... 90 ampBattery Cold Cranking ........................... 1,146 ampsAir cleaner ....................................... Double elementGovernor ................................................. ElectronicFuel Usage*

Heavy - ............................... 18.5 gph (70.0 l/hr)Average - ............................ 15.4 gph (58.3 l/hr)Light - ................................. 12.3 gph (46.6 l/hr)

*Fuel economy varies widely depending upon application.

The "Heavy" category represents nearly continuous operation intough digging applications. The "Light" category representsapplications that utilize the machine about 50% of the time, in

easier digging.

Hydraulic System

Two variable displacement axial piston pumpsand one gear pump for pilot controls, withLink-Belt Inte-LXTM Control System. Link-Belt Inte-LXTM Control includes: electric engine control, fiveselectable working modes, automatic power-up,auto/one touch idling, automatic speed shifting,free swing, cushioned attachment, swing anti-braking system, and two safety lockout switchesincluding gate lock.

Hydraulic PumpsTwo variable volume piston pumps provide powerfor attachment, swing and travel.

Maximum flow .......... 2 x 132.1 gpm (2 x 500 l/min)Pilot pump max. flow ................... 7.1 gpm (27 l/min)

Relief Valve SettingsBoom/arm/bucket ................ 4,550 psi (320 kg/cm2) in Power-Up Mode ......... 4,970 psi (350 kg/cm2)Swing circuit ......................... 4,050 psi (285 kg/cm2)Travel ................................... 4,970 psi (350 kg/cm2)

Hydraulic Cylinders – number of cylinders – borex rod x stroke.

Boom .................................... 2 – 7.9" x 5.5" x 74.5"(200 mm x 140 mm x 1 893 mm)

Arm ...................................... 1 – 8.5" x 5.9" x 85.6"(215 mm x 150 mm x 2 175 mm)

Excavator Bucket .................... 1 – 7.5" x 5.1" x 61.2"(190 mm x 130 mm x 1 555 mm)

Oil Filtration

Nephron® filter .......................................... 1 micronReturn, pilot ............................................. 10 micronSuction filter ........................................... 105 micron

Control Valve One 4-spool valve and one 5-spoolvalve with auxiliary spool.

downshifts from high to low speed for increasedtractive effort and then automatically returns tohigh speed when travel conditions permit.

Max. travel speed ........ 1.8/2.7 mph (2.9/4.3 km/h)Traction force .................... 122,300 lbs. (55 465 kgf)Gradeability ..................................................... 70%

Spring applied, hydraulically released discparking brake built into each motor. Each travelmotor equipped with counterbalance valve toprevent overspeeding down an incline and3-stage reliefs for smooth starts and stops.

Lubricant andCoolant CapacityHydraulic tank ............................. 82 gal. (310 liters)Hydraulic system ........................ 190 gal. (720 liters)Final drive (per side) ................... 3.6 gal. (13.5 liters)Swing drive ............................... 3.6 gal. (13.5 liters)Engine ....................................... 12.4 gal. (47 liters)Fuel tank ................................... 238 gal. (900 liters)Cooling system ......................... 26.4 gal. (100 liters)

AttachmentBoom (Standard excavator) ................. 27' 7" (8.4 m)

Available Arms Digging Force*• 12' 0" (3.66 m) ............... 61,600 lbs. (27 940 kgf)

in Auto Power-Up Mode .. 67,440 lbs. (30 590 kgf)

• 14' 7" (4.44 m) ............... 52,160 lbs. (23 660 kgf)in Auto Power-Up Mode . 56,880 lbs. (25 800 kgf)

• 18' 5" (5.62 m) ............... 45,410 lbs. (20 598 kgf)in Auto Power-Up Mode .. 49,680 lbs. (22 534 kgf)

Boom (Mass excavator) ..................... 23' 9" (7.25 m)

Available Arms Digging Force*• 9' 9" (2.98 m) (Mass) ........ 71,260 lbs. (32 320 kgf)

in Auto Power-Up Mode . 78,010 lbs. (35 380 kgf)

Standard ExcavatorBucket Digging Force ....... 74,190 lbs. (33 650 kgf)in Auto Power-Up Mode ..... 81,160 lbs. (36 810 kgf)

Mass ExcavatorBucket Digging Force ....... 96,670 lbs. (43 850 kgf)in Auto Power-Up Mode ... 105,660 lbs. (47 930 kgf)

*Digging force ratings are based on ISO 6015, “EarthmovingMachinery – Hydraulic Excavators – Tool Forces”.

Operating Weight

Standard Excavator - Working weight with29.5" (750 mm) shoes, 27' 7" (8.40 m) boom,12' 0" (3.66 m) arm, 6,610 lb. (3 000 kg) bucketand 27,560 lbs. (12 500 kg) counterweight ....................................... 174,600 lbs. (79 200 kg)

Mass Excavator - Working weight with 29.5"(750 mm) shoes, 23' 9" (7.25 m) boom, 9' 9"(2.98 m) arm, 7,630 lb. (3 460 kg) bucket and27,560 lbs. (12 500 kg) counterweight .............................................. 174,600 lbs. (79 200 kg)

Dimensions


Working Ranges

Mass Excavator

Machine equipped with 9' 9" Arm23' 9" (7.25 m) boom. (2.98 m)

A Max. digging radius 40' 5"(12.31 m)

B Max. digging radius 39' 4"@ ground level (11.99 m)

C Max. digging depth 23' 1"(7.03 m)

D Max. digging height 38' 7"(11.76 m)

E Max. dumping height 25' 11"(7.89 m)

F Digging depth – 8' 22' 7"(2.44 m) level bottom (6.88 m)

G Bucket wrist angle 162°

H Max. vertical wall depth 13' 11"(4.25 m)

Machine equipped with:

1

2 4

3Mass Excavator -9' 9" (2.98 m) arm

12' 0" (3.66 m) arm

2 3 41

Extended Side rails

Machine equipped with 12' 0" Arm 14' 7" 18' 5"27' 7" (8.40 m) boom. (3.66 m) (4.44 m) (5.62 m)

A Max. digging radius 46' 4" 49' 0" 52' 10"(14.12 m) (14.94 m) (16.11 m)

B Max. digging radius 45' 5" 48' 2" 52' 0"@ ground level (13.84 m) (14.68 m) (15.86 m)

C Max. digging depth 28' 6" 31' 1" 35' 0"(8.69 m) (9.47 m) (10.66 m)

D Max. digging height 42' 4" 44' 7" 46' 11"(12.91 m) (13.60 m) (14.66 m)

E Max. dumping height 29' 3" 31' 2" 33' 4"(8.92 m) (9.51 m) (10.17 m)

F Digging depth – 8' 28' 1" 30' 9" 34' 8"(2.44 m) level bottom (8.57 m) (9.36 m) (10.56 m)

G Bucket wrist angle 167° 167° 167°

H Max. vertical wall depth 21' 2" 25' 5" 29' 11"(6.44 m) (7.75 m) (9.11 m)

Standard Excavator

46' 5"(14.14 m)

42' 8"(13.01 m)

46' 3"(14.10 m)

45' 0"(13.71 m)

11' 9" (3.58 m)

14' 7" (4.44 m) arm

18' 5" (5.62 m) arm

16' 7" (5.05 m)

15' 9" (4.81 m)

16' 5" (5.0 m)

20' 3" (6.17 m)

20' 10" (6.36 m) 9' 3" (2.83 m)

2' 11"(.89 m)

5' 3"(1.59 m)

12' 3" (3.74 m)

2' 6" (750 mm)

12' 5

"(3

.79

m)

3' 3"(1.0 m)

6' 11"(2.12 m)

6' 7"(2.01 m)

13' 7"(2.12 m)

16' 8" (5.07 m)

13' 4" (4.07 m)

Powerful Breakout ForcesDeep and wide box sections of highyield steel and deep groove welding holdup to high breakout forces, strong liftingcapacities and the stresses of alliedattachments such as hammers,thumbs, compactors, shears, grapplesand crushers.

Strength and DurabilityLX heavy duty booms and arms haveinternal baffles which provide betterstrength and durability to withstandtorsional loads.

LC UndercarriageLong undercarriages incorporate heavy dutyexcavator style components and improveboth stability and ground bearing pressure.The 800 LX is designed with expandable/retractable side frames for ease of transport.High torque compact final drives keep yougoing up steep grades and through deepmud.

Bearing Tub

Built into the carbody is the turntablebearing “tub” which extends down throughthe top plate and is welded to the bottom ofthe carbody as well as the top for increasedstrength and durability.

Upper and Attachments

Undercarriage

Easy Maintenance SystemChrome plated pins mounted in greaseimpregnated brass bushings on completeattachment make a durable and long

lasting connection. This also makes itpossible to extend the lubrication interval onthis type of pin to once every 6 months or1,000 hours of operation, whichever comesfirst.

A. The surface of the bushing is stratifiedwith a solid lubricant in hard brass toprotect the parts from abrasion.

B. The pin’s surface is plate-processed toincrease hardness and protect fromabrasion

C. The original dust seal is double-structuredto keep out dust and dirt and protect fromsubsequent abrasion.

Three Arm Choices (standard excavator)and a wide variety of buckets provide thereach and breakout forces for optimumproductivity.

Mass Excavator attachment is alsoavailable.

Two-Speed Travel MotorOffers smooth shifting and the needed pullwhen going up grades and making turns.

Strut Type Chain LinksThere are no weak links in our chain. Strutsreduce twisting and hold up to severe pointloading when all of the machine weight istransferred through one roller. Track pins aregreased and sealed for long life.

Track RollersFilled with synthetic oil to reduce heatbuild up and for long term reliability.

Track AdjustmentAdjustments are made easy with standardgrease cylinder track adjusters and shockabsorbing springs.

Side FramesSide frames expand/retract : use inexpanded position only to dig, retractedposition to transport.

1

2

3

4

Dependable Isuzu PowerAuto Engine Warm-UpIf the engine temperature is low followingstart-up, the auto warm-up system willoperate automatically and continue withengine speed increasing gradually untilnormal engine operating temperaturesare reached.

Air FiltrationLX Series engines are equipped with a dualelement air filter with an evacuator cup andrestriction indicator for ease of maintenance.

Larger MufflerThe LX series features a larger muffler whichabsorbs more sound and makes this thequietest Link-Belt yet.

Emergency EngineShutdownIn emergency situations, the engine can beshut down with the push of a switch locatedon the control panel in the cab. This switchmust be re-engaged prior to restarting theengine.

Engine Product SupportIsuzu North America offers 24-hour accessto their full line of engine parts through 2regional distribution centers, 27 MasterDistributors and 690 Authorized ServiceDealers.

Maintaining engine revolution at a fixed rateregardless of the load prevents the energy loss thatoccurs when shifting cycle times to accommodatehigher or lower loads.

Advantages of EEC

Tier II CompliantLX engines meet EPA Tier II standardsrequirements.

Idle StartAt start-up, the engine defaults to idleregardless of throttle position. This preventsover revving a cold engine, helping toextend its service life.

Low Idle UpWhen low temperatures or other conditionsreduce engine rpm to a point thatalternator output won’t keep the batterycharged, Inte-LXTM automatically increasesthe idle speed from 900 to 1100 rpmkeeping the batteries fully charged.

First In ClassThe 800 LX is the first excavator in it’s classto utilize an electronic engine controlfunction. By optimizing the level of fuelinjection to match the load, this responsivenew system assures more efficient use offuel, plus by keeping the engine closer tothe target engine speed, less lugging takesplace so cycle times are faster, exhaustnoise, vibration, and smoke are reducedmaking the environment in the cab andaround the machine cleaner and quieter.

Electronic Engine Control(EEC)Inte-LXTM maintains engine rpm’s when loaddemands change. Engines equipped withmechanical governors spike rpm’s up-and-down when operating loads increase anddecrease. This phenomena causes enginesto consume extra fuel and be louder.

Low Fuel ConsumptionThe electronic governor responds tochanges in operating loads quicker thana mechanical governor. As a result, EECregulates the amount of fuel injectionaccurately and quickly.

Lower, Cleaner EmissionsLow fuel consumption results in high ignitionefficiency (cleaner emission) and lowemissions.

Low Sound LevelsAt high idle, EEC can control enginespeed rpm at rated horsepower. Thismeans the engine doesn’t overrun,resulting in lower sound levels.

Low VibrationEEC causes engine rpm to be stable,resulting in low vibration.

Lifting Capacities (Standard Excavator) w/sideframes extended



Radius of Load

10' 0" (3.05 m) 15' 0" (4.57 m) 20' 0" (6.10 m) 25' 0" (7.62 m) 30' 0" (9.14 m) 35' 0" (10.66 m) Cap. at Max. Reach

End Side End Side End Side End Side End Side End Side End Side

+30' 0" lbs.(9.14 m) kg

+25' 0" lbs.(7.62 m) kg



Line kg-5' 0" lbs.

(1.52 m) kg-10' 0" lbs.(3.05 m) kg-15' 0" lbs.(4.57 m) kg-20' 0" lbs.(6.10 m) kg

BucketHookHeight

16,420* 16,420*7 440* 7 440*

28,540* 28,540* 22,530* 22,530* 16,360* 16,360*12 940* 12 940* 10 210* 10 210* 7 420* 7 420*30,570* 30,570* 27,850* 23,200 16,760* 16,760*13 860* 13 860* 12 630* 10 520 7 600* 7 600*

70,910* 70,910* 49,460* 49,460* 39,130* 39,130* 33,110* 29,170 29,270* 22,190 17,610* 17,610*32 160* 32 160* 22 430* 22 430* 17 740* 17 740* 15 010* 13 230 13 270* 10 060 7 980* 7 980*

56,720* 51,580 43,390* 36,700 35,700* 27,460 30,790* 21,140 18,950* 16,67025 720* 23 390 19 680* 16 640 16 190* 12 450 13 960* 9 580 8 590* 7 560

36,340* 36,340* 61,470* 48,140 46,710* 34,430 37,860* 25,980 32,070* 20,190 20,970* 16,28016 480* 16 480* 27 880* 21 830 21 180* 15 610 17 170* 11 780 14 540* 9 150 9 510* 7 38046,410* 46,410* 63,190* 46,310 48,540* 32,910 39,170* 24,890 32,760* 19,480 23,970* 16,48021 050* 21 050* 28 660* 21 000 22 010* 14 920 17 760* 11 290 14 850* 8 830 10 870* 7 470

40,280* 40,280* 60,960* 60,960* 62,310* 45,610 48,630* 32,120 39,280* 24,260 32,430* 19,090 28,600* 17,38018 270* 18 270* 27 650* 27 650* 28 260* 20 680 22 050* 14 560 17 810* 11 000 14 710* 8 650 12 970* 7 88056,710* 56,710* 76,290* 75,780 59,090* 45,700 46,790* 31,970 37,780* 24,130 30,680* 19,28025 720* 25 720* 34 600* 34 370 26 800* 20 720 21 220* 14 500 17 130* 10 940 13 910* 8 74074,790* 74,790* 67,350* 67,350* 53,240* 46,470 42,520* 32,430 33,810* 24,580 31,260* 22,88033 920* 33 920* 30 540* 30 540* 24 140* 21 070 19 280* 14 710 15 330* 11 140 14 170* 10 370

54,210* 54,210* 43,640* 43,640* 34,380* 33,680 30,920* 30,27024 580* 24 580* 19 790* 19 790* 15 590* 15 270 14 020* 13 730

Radius of Load10' 0" (3.05 m) 15' 0" (4.57 m) 20' 0" (6.10 m) 25' 0" (7.62 m) 30' 0" (9.14 m) 35' 0" (10.66 m) 40' 0" (12.19 m) Cap. at Max. Reach

End Side End Side End Side End Side End Side End Side End Side End Side

+35' 0" lbs.(10.66 m) kg

+30' 0" lbs.(9.14 m) kg

+25' 0" lbs.(7.62 m) kg



Line kg-5' 0" lbs.


BucketHookHeight

10,980* 10,980*4 980* 4 980*

16,730* 16,730* 9,690* 9,690*7 580* 7 580* 4 390* 4 390*22,150* 22,150* 9,480* 9,480*10 040* 10 040* 4 300* 4 300*

27,850* 27,850* 25,520* 23,460 15,440* 15,440* 9,550* 9,550*12 630* 12 630* 11 570* 10 640 7 000* 7 000* 4 330* 4 330*

35,820* 35,820* 30,590* 29,590 27,160* 22,340 20,150* 17,110 9,880* 9,880*16 240* 16 240* 13 870* 13 420 12 310* 10 130 9 130* 7 760 4 480* 4 480*

64,210* 64,210* 52,440* 52,440* 40,470* 37,410 33,470* 27,720 28,940* 21,150 23,750* 16,390 10,490* 10,490*29 120* 29 120* 23 780* 23 780* 18 350* 16 960 15 180* 12 570 13 120* 9 590 10 770* 7 430 4 750* 4 750*42,980* 42,980* 58,500* 49,040 44,420* 34,790 36,030* 26,030 30,550* 20,060 25,990* 15,710 11,430* 11,430*19 490* 19 490* 26 530* 22 240 20 140* 15 780 16 340* 11 800 13 850* 9 090 11 780* 7 120 5 180* 5 180*

21,790* 21,790* 45,120* 45,120* 61,750* 46,450 47,040* 32,900 37,860* 24,710 31,680* 19,170 25,240* 15,170 12,830* 12,830*9 880* 9 880* 20 460* 20 460* 28 000* 21 060 21 330* 14 920 17 170* 11 200 14 360* 8 690 11 440* 6 880 5 810* 5 810*33,900* 33,900* 54,210* 54,210* 62,310* 45,170 48,040* 31,750 38,640* 23,850 31,930 18,590 18,450* 14,890 14,910* 14,63015 370* 15 370* 24 580* 24 580* 28 260* 20 480 21 790* 14 400 17 520* 10 810 14 480 8 430 8 360* 6 750 6 760* 6 63046,540* 46,540* 67,370* 67,370* 60,450* 44,820 47,230* 31,280 38,020* 23,460 31,100* 18,380 18,130* 15,99021 110* 21 110* 30 550* 30 550* 27 410* 20 330 21 420* 14 180 17 240* 10 640 14 100* 8 330 8 220* 7 25060,780* 60,780* 73,090* 73,090* 56,090* 45,220 44,290* 31,420 35,490* 23,580 27,380* 18,680 23,580* 18,46027 560* 27 560* 33 150* 33 150* 25 440* 20 510 20 080* 14 250 16 090* 10 690 12 410* 8 470 10 690* 8 37077,890* 77,890* 62,060* 62,060* 48,560* 46,350 38,380* 32,240 29,680* 24,400 27,470* 23,04035 330* 35 330* 28 150* 28 150* 22 020* 21 020 17 400* 14 620 13 460* 11 060 12 460* 10 450

45,460* 45,460* 35,960* 35,960* 26,870* 26,870* 25,810* 25,810*20 620* 20 620* 16 310* 16 310* 12 180* 12 180* 11 700* 11 700*

Advanced HydraulicSystemTop-of-the-Class Cycle Times/FuelEfficientThe LX Series hydraulic system efficientlydelivers power, speed and control whenand where it’s needed. Fuel consumptionand cycle times are more efficient inswing/dump operations over conventionalmodels. This is accomplished throughreducing system pressure loss, re-usingreturn oil and providing double pump flowduring key operations.

Regeneration SystemBy re-using the returning oil from thearm and the boom, ground excavatingoperation speed is increased.

Two Hydraulic ReturnLinesTwo hydraulic returns lines mean fasterspeed in the system, and reduces backpressure build-up.

Performance2 Speed Boom and ArmThe 2-speed boom lifting and arm openingand closing function provides the LX serieswith top-of-its-class lifting speed especially inswing/excavating simultaneous operationssuch as truck loading.

Auto Power-SwingThis patent pending design incorporatesa selector valve that helps maintainattachment and hydraulic flow to achieveexcellent swing and digging forces in sidewall-cut operations. In normal diggingwhen side pressure is not needed, LXsends all the flow to the attachment alwaysinsuring the best performance for eitheroperation.

Cushioned SwingThis built-in special cushion valve greatlyreduces the shock and vibration at the endof each swing cycle.

Cushioned AttachmentControlIn addition to having cushioned cylinders,selectable cushioned attachment controllets you smooth out the attachmentmovements. A cushion valve in the boomand arm circuits reduce shock loading andvibration during attachment operation.

Free SwingAllows the operator to disengage the swingbrake providing crane-like precision andcontrol when handling loads.

Single Pedal TravelAllows the operator to engage both tracks atthe same time using only one pedal. Thiskeeps the machine in line with the ditch andprovides safety and ease in loading/unloading the machine for transport.

Automatic Speed ShiftingWhen operating in difficult travelconditions, the travel motor automaticallydownshifts from high to low speed forincreased tractive effort and thenautomatically returns to high speedwhen travel conditions permit.

Fuel Tank CapacityThe LX Series fuel tank provides thecapacity to reduce refueling frequency,allowing for an extended work day.

Lifting Capacities (Mass Excavator) w/side frames extended

1. Lifting capacities shown should not beexceeded. Weight of all lifting accessoriesmust be deducted from the above liftingcapacities.

2. Lifting capacities are based on machinestanding on firm, uniform supporting surface.User must make allowances for job conditionssuch as soft or uneven ground.

3. Lifting capacities shown do not exceed 75% ofminimum tipping loads or 87% of hydrauliccapacities. Capacities marked with an asterisk (*)are limited by hydraulic capacities.

4. Least stable position is over the side.5. Operator should be fully acquainted

with the Operator’s Manual & Operating SafetyBooklet, furnished by LBX before operating themachine.

6. Capacities apply only to the machine asoriginally manufactured and normallyequipped by LBX Company, LLC.

7. Lift capacity ratings are based on SAEJ/ISO 10567, “Earthmoving Machinery– Hydraulic Excavators – Lift Capacity”.

8. Lifting or digging operations with theside frames in the retracted positionsare not permitted.

Notes: Excavator lifting capacities

9' 9" (2.98 m) Armwith 23' 9" (7.25 m) Boom and 7,625 lb. (3 458 kg) Bucket.Auto Power-Up Mode Applied

18' 5" (5.62 m) Arm w/side frames extendedwith 27' 7" (8.40 m) Boom and 5,710 lb. (2 590 kg) Bucket.Auto Power-Up Mode Applied

Radius of Load

10' 0" (3.05 m) 15' 0" (4.57 m) 20' 0" (6.10 m) 25' 0" (7.62 m) 30' 0" (9.14 m) 35' 0" (10.66 m) 40' 0" (12.19 m) 45' 0" (13.71 m) Cap. at Max. Reach

End Side End Side End Side End Side End Side End Side End Side End Side End Side

+35' 0" lbs.(10.66 m) kg

+30' 0" lbs.(9.14 m) kg

+25' 0" lbs.(7.62 m) kg



Line kg-5' 0" lbs.


BucketHookHeight

11,800* 11,800*5 350* 5 350*

18,650* 18,650* 10,800* 10,800*8 450* 8 450* 4 890* 4 890*22,350* 22,350* 12,000* 12,000* 10,200* 10,200*10 130* 10 130* 5 440* 5 440* 4 620* 4 620*23,450* 22,050 17,550* 16,700* 9,950* 9,950*10 630* 10 000 7 960* 7 570* 4 510* 4 510*

32,600* 32,600* 28,000* 27,700 25,000* 20,750 21,400* 15,850 10,050* 10,050*14 780* 14 780* 12 700* 12 560 11 330* 9 410 9 700* 7 180 4 550* 4 550*

72,400* 72,400* 48,900* 48,900* 37,500* 35,250 30,950* 25,800 26,800* 19,500 24,050* 15,050 10,350* 10,350*32 840* 32 840* 22 180* 22 180* 17 000* 15 980 14 030* 11 700 12 150* 8 840 10 900* 6 820 4 690* 4 690*48,250* 48,250* 55,750* 47,100 41,800* 32,750 33,650* 24,150 28,500* 18,350 24,950* 14,250 11,050* 11,050*21 880* 21 880* 25 280* 21 360 18 960* 14 850 15 260* 10 950 12 920* 8 320 11 310* 6 460 5 010* 5 010*48,200* 48,200* 59,700* 44,700 44,800* 30,950 35,700* 22,850 29,750* 17,450 24,550 13,650 12,200* 12,200*21 860* 21 860* 27 070* 20 270 20 320* 14 030 16 190* 10 360 13 490* 7 910 11 130 6 190 5 530* 5 530*57,050* 57,050* 60,750* 43,400 46,150* 29,800 36,700* 21,950 30,050 16,800 22,550* 13,300 13,950* 12,70025 870* 25 870* 27 550* 19 680 20 930* 13 510 16 640* 9 950 13 630 7 620 10 220* 6 030 6 320* 5 76070,900* 70,900* 59,250* 42,900 45,600* 29,250 36,300* 21,500 29,500* 16,550 16,750* 13,85032 160* 32 160* 26 870* 19 450 20 680* 13 260 16 460* 9 750 13 380* 7 500 7 590* 6 280

62,850* 62,850* 73,250* 73,150 55,100* 43,050 42,900* 29,250 34,050* 21,500 26,800* 16,750 21,550* 15,95028 500* 28 500* 33 220* 33 180 24 990* 19 520 19 450* 13 260 15 440* 9 750 12 150* 7 590 9 770* 7 23082,000* 82,000* 62,300* 62,300* 47,850* 43,750 37,350* 29,800 28,750* 22,100 25,100* 19,90037 190* 37 190* 28 250* 28 250* 21 700* 19 840 16 940* 13 510 13 040* 10 020 11 380* 9 020

45,950* 45,950 * 35,750* 35,750* 26,700* 26,700* 23,550* 23,550*20 840* 20 840* 16 210* 16 210* 12 110* 12 110* 10 680* 10 680*

Radius of Load

10' 0" (3.05 m) 15' 0" (4.57 m) 20' 0" (6.10 m) 25' 0" (7.62 m) 30' 0" (9.14 m) Cap. at Max. Reach

End Side End Side End Side End Side End Side End Side

+30' 0" lbs.(9.14 m) kg

+25' 0" lbs.(7.62 m) kg



Line kg-5' 0" lbs.

(1.52 m) kg-10' 0" lbs.(3.05 m) kg-15' 0" lbs.(4.57 m) kg

26,500* 26,500*12 020* 12 020*26,200* 26,200*11 880* 11 880*

38,730* 38,730* 34,920* 30,420 26,900* 26,900*17 560* 17 560* 15 830* 13 790 12 200* 12 200*

70,980* 70,980* 52,030* 52,030* 42,420* 39,980 36,730* 29,150 28,510* 24,11032 190* 32 190* 23 600* 23 600* 19 240* 18 130 16 660* 13 220 12 930* 10 93084,560* 84,560* 58,950* 53,500 46,210* 37,520 38,720* 27,760 31,200* 22,57038 350* 38 350* 26 730* 24 260 20 960* 17 010 17 560* 12 590 14 150* 10 23068,440* 68,440* 63,610* 50,140 49,100* 35,470 40,250* 26,540 35,430* 22,08031 040* 31 040* 28 850* 22 740 22 270* 16 080 18 250* 12 030 16 070* 10 01077,680* 77,680* 64,970* 48,260 50,270* 34,120 40,620* 25,700 36,740* 22,66035 230* 35 230* 29 470* 21 890 22 800* 15 470 18 420* 11 650 16 660* 10 270

59,110* 59,110* 83,320* 78,050 62,930* 47,610 49,070* 33,520 38,970* 25,400 37,790* 24,62026 810* 26 810* 37 790* 35 400 28 540* 21 590 22 250* 15 200 17 670* 11 520 17 140* 11 16084,380* 84,380* 73,900* 73,900* 57,200* 47,950 44,590* 33,730 38,550* 28,90038 270* 38 270* 33 520* 33 520* 25 940* 21 740 20 220* 15 290 17 480* 13 100

58,970* 58,970* 46,220* 46,220* 38,060* 38,060*26 740* 26 740* 20 960* 20 960* 17 260* 17 260*

BucketHookHeight

Lifting Capacities (Standard Excavator) w/sideframes extended (cont.)


Inte-LXTM, the intelligent computer commandcontrol system monitors hydraulic output,pressures, and regulates engine perfor-mance for the maximum balance betweenspeed, power and fuel efficiency neededto handle the job.

Auto Power-UpThe LX series can quickly respond tochanges in operating conditions,automatically supplying a power increase,without operator interaction and regardlessof the work mode. Hydraulic pressuresensors detect resistance and pressure isincreased by 9% for 8 seconds. AutoPower-Up stays on 100% of the time inthe “L” mode.

Anti-Theft DeviceYour Link-Belt distributor can set up your Inte-LXTM control system to include a passwordprotection feature that requires thepassword to start and run the machine.

One-Touch and Auto IdleControlWhen user-preset time has elapsed afterleaving the control handles in the neutralposition, auto-idling automatically drops theengine to idle speed (900 rpm). Or, youcan choose to use the one-touch idlingswitch, located at the top of the rightcontroller so that you are always in control.

Inte-LXTM

Operating ModesThe LX series enables the operator to have achoice on how the machine is operated.Simply choose the work mode that matchesthe machines output to the job application.Five operating modes are available.

A: Auto-ModeThe most revolutionary approach tomaximizing power & fuel efficiencyavailable today. Just select the Auto-Modewith the switch panel. Using actual workingpressure readings, Inte-LXTM instantlychanges modes assuring the best combina-tion of speed and power while you can stayfocused on the work at hand.

H: Heavy ModeFor heavy excavation or whenever you needextra power and maximum speed.

S: Standard ModeFor standard digging and loadingoperations reducing fuel consumption.

L: Lift ModeFor lifting and other operations that needfingertip accuracy.

Allied AttachmentWork ModeAutomatically adjusts engine speed andpump output to match additional attach-ments such as hammers. The engine rpm’sare presettable to match the hydraulicrequirements.

On-Board DiagnosticsAn on-board diagnostic system allowsservice personnel to quickly analyze up to148 items in four categories;

•Machine Status: The diagnosticsystem provides a detailed view of pumppressure, engine rpm, water temperature,oil temperature, fuel temperature, throttlesetting and ongoing operating functionssuch as auto power-up and auto-mode.

•Troubleshooting: Service personnelcan trace electrical faults such as sensorfailures and harness damage.

•History: An on-going record of machinefaults is stored in the computer includingthe hour meter reading at time of the faultto assist in the diagnostics procedure.

•Systems Configuration: Servicepersonnel can change machineoperating characteristics such as; timedelay for auto-idle, language selection,and engine rpm preset for alliedattachment mode.

Arm Arm Arm

Bucket Width # 12' 0" 14' 7" 18' 5"Type Capacity Outside Lip Weight Teeth (3.66 m) (4.44 m) (5.62 m)

2.53 cu. yd. (1.93 m3) 42" (1 067 mm) 6,403 lb. (2 904 kg) 4 H H M3.00 cu. yd. (2.29 m3) 48" (1 219 mm) 6,803 lb. (3 086 kg) 4 H H M

ESCO 3.48 cu. yd. (2.66 m3) 54" (1 372 mm) 7,203 lb. (3 267 kg) 4 H M LHDP 3.96 cu. yd. (3.03 m3) 60" (1 524 mm) 7,780 lb. (3 529 kg) 5 M L N/A

4.45 cu. yd. (3.40 m3) 66" (1 676 mm) 8,180 lb. (3 710 kg) 5 M L N/A4.94 cu. yd. (3.78 m3) 72" (1 829 mm) 8,580 lb. (3 892 kg) 5 L N/A N/A5.42 cu. yd. (4.14 m3) 78" (1 981 mm) 9,157 lb. (4 154 kg) 6 L N/A N/A5.91 cu. yd. (4.52 m3) 84" (2 134 mm) 9,557 lb. (4 335 kg) 6 N/A N/A N/A

2.47 cu. yd. (1.89 m3) 45" (1 143 mm) 6,470 lb. (2 935 kg) 4 H H HESCO 3.26 cu. yd. (2.49 m3) 56" (1 422 mm) 7,211 lb. (3 271 kg) 4 H M LXDP 3.99 cu. yd. (3.05 m3) 66" (1 676 mm) 8,061 lb. (3 656 kg) 5 M L N/A

4.43 cu. yd. (3.39 m3) 72" (1 829 mm) 8,466 lb. (3 840 kg) 5 L L N/A5.30 cu. yd. (4.05 m3) 84" (2 134 mm) 9,451 lb. (4 287 kg) 6 L N/A N/A

Bucket Sizes - Standard Excavator






Arm

Bucket Width # 9' 9"Type Capacity Outside Lip Weight Teeth (2.98m)

2.53 cu. yd. (1.93 m3) 42" (1 067 mm) 6,403 lb. (2 904 kg) 4 H3.00 cu. yd. (2.29 m3) 48" (1 219 mm) 6,803 lb. (3 086 kg) 4 H

ESCO 3.48 cu. yd. (2.66 m3) 54" (1 372 mm) 7,203 lb. (3 267 kg) 4 HHDP 3.96 cu. yd. (3.03 m3) 60" (1 524 mm) 7,780 lb. (3 529 kg) 5 H

4.45 cu. yd. (3.40 m3) 66" (1 676 mm) 8,180 lb. (3 710 kg) 5 H4.94 cu. yd. (3.78 m3) 72" (1 829 mm) 8,580 lb. (3 892 kg) 5 H5.42 cu. yd. (4.14 m3) 78" (1 981 mm) 9,157 lb. (4 154 kg) 6 M5.91 cu. yd. (4.52 m3) 84" (2 134 mm) 9,557 lb. (4 335 kg) 6 M

2.47 cu. yd. (1.89 m3) 45" (1 143 mm) 6,470 lb. (2 935 kg) 4 HESCO 3.26 cu. yd. (2.49 m3) 56" (1 422 mm) 7,211 lb. (3 271 kg) 4 HXDP 3.99 cu. yd. (3.05 m3) 66" (1 676 mm) 8,061 lb. (3 656 kg) 5 H

4.43 cu. yd. (3.39 m3) 72" (1 829 mm) 8,466 lb. (3 840 kg) 5 H5.30 cu. yd. (4.05 m3) 84" (2 134 mm) 9,451 lb. (4 287 kg) 6 M

Bucket Sizes - Mass Excavator






Large, Low Noise CabDesignA wide cab design provides expandedleg and elbow room. Six silicon filledisolation mounts float the entire cababove the noise and vibration of an alreadyquiet machine greatly reducing operatorfatigue. Large entry door and access widthmakes entering and exiting the cab abreeze.

Control PanelMany machine function switches areconcentrated in a panel in clear viewand easy reach of the operator.

Tilting Console and SlidingSeatThe seat slides independently of the controlconsoles to assure optimal joystick positionsat all times.The joysticks canbe tiltedto any of threesettings,allowing theoperator to workin the mostcomfortable position. The entire platformcan then be moved forward or backward forbest foot pedal positioning.

Panoramic VisibilityThis cab provides more window spacethan ever. Even the sunroof is large. TheOperator’s “office with a view” has rear andside windows made of LEXAN®

MARGUARD™. Standard vandal coversprotect the safety glass front windowsand stow on top when you’re working.

Informative LCD MonitorLarge size LCD Monitor displays graphicallya wide range of operating information suchas; engine temperature,hydraulic oil temperature, fuel level, travelspeed, work mode and engineidle. Additional messages includesystem/machine warnings and servicedue messages in your choice of Englishand 13 other languages. Backlit illuminationensures displays are alwaysreadable – day and night.

Operator's Control Station

All Weather VisibilityWith built-in washer and intermittentspeed control, the wiper keeps yourwindshield clear, whatever the conditionoutside. The “rise-up” design takes the wiperarm and blade out of the line ofsight when its not in use, plus lifts the bladefrom the cab surface so that it doesn’t freezeto the cab in icy weather.

Fresh Air Induction-TypeClimate ControlLX provides exceptional heating/cooling ca-pabilities with a climate control system thatautomatically regulates the temperature forthe operator’s comfort. Now with 6 vents, LXSeries excavators provide exceptional aircirculation for optimum operator comfort.Front-side air outlet and defroster ensure acomfortable operating environment while theopen/closetype rear win-dow furtherimproves theventilation.

Best Seat at the SiteThe KAB 515 seat adjusts to your sizeand comfort. The semi-bucket seat providesfirm support and comfort with armrests,adjustable seat suspension, adjustablelumbar support, and durable urethanecushions.

TripmeterIn addition to the hour meter, LX has addeda Tripmeter. Every job or application canbe measured.

AM/FM Stereo RadioStandard equipment.

Emergency EscapeWindowAllows operator to escape from the rearwindow in case of emergency.

Transportation SpecificationsUpper Structure w/TTB and Lower Cross Frame

Weight: 51,370 lbs. (23 300 kg) Dimension A: 17' 6" (5.34 m)Weight: W/FOPS 52,250 lbs. (23 700 kg) Dimension B: 9' 1" (2.77 m)

Dimension C: 9' 1" (2.78 m)Dimension D: 18' 1" (5.50 m)

FOPS Head Guard:(Optional)Weight: 705 lbs. (320 kg).

A

BC

DW/FOPS

Counter Weight

A

B

C Weight: 27,557 lbs. (12 500 kg)Dimension A: 11' 5" (3.47 m)Dimension B: 4' 7" (1.39 m)Dimension C: 2' 8" (.82 m)

Total Weight: 165 lbs. (75 kg)

Dimension A: 6' 3" (1.91 m)Dimension B: 3' 1" (.94 m)Dimension C: 3' 9" (1.15 m)Dimension D: 8' 10" (2.70 m)Dimension E: 2' 0" (.60 m)Dimension F: 4' 5" (1.35 m)Dimension G: 2' 4" (.71 m)Dimension H: 5' 10" (1.77 m)Dimension I: 2' 9" (.85 m)Right Side Cab Side

Hand RailsB

A E

F

C D G H

I

Undercarriage

A BC

Shoe Width: Weight: (per side)29.5" (750 mm) 29,321 lbs. (13 300 kg)35.4" (900 mm) 30,864 lbs. (14 000 kg)43.3" (1100 mm) 32,628 lbs. (14 800 kg)Dimension A:

W/ 29.5" (750 mm) shoes - 39.7" (1 010 mm)W/ 35.4" (900 mm) shoes - 39.7" (1 010 mm)W/ 43.3" (1 100 mm) shoes - 43.3" (1 100 mm)

Dimension B: 16' 7"(5070 mm)Dimension C: 20' 10" (6360 mm)

Side Frame with Steps:

Designed for Durability and Performance...Maximized OperatorComfortThe industry’s largest cab providing lownoise, climate controlled heat and airconditioning, standard. Page 3

Auto Power-UpAuto power-up automatically increasessystem pressure by 9% to power throughtough ground or when lifting a heavy load.Page 4

Cleaner Side-Wall CutsWith Auto Power-Swing, Inte-LXTM

automatically prioritizes swing torque whensimultaneously working the swing andattachment. Page 5

Low Ground Pressure andExceptional StabilityLC undercarriage for low ground pressureand stability incorporates heavy-dutyexcavator style components. Page 7

Long Life Pin and BushingDesignChrome pins and grease impregnatedbushings throughout the completeattachment hold up to torsional stressescreated in these large excavators andreduces the greasing interval. Page 7

Heavy Duty Boom andArmBuilt to handle powerful breakout forces,strong lifting capacities and the stresses ofallied attachments. Page 7

Faster Cycle TimesA smarter more efficient hydraulic systemuses dual pump flow, auto power swing andregenerative circuits for increasedproductivity. Page 5

Anti-Theft SystemTo protect your investment, a passwordprotected anti-theft system comes as standardequipment and can be activated at the userschoice. Page 4

Superior ServiceabilityOn-board diagnostics with memoryand fewer hydraulic oil changes result insuperior serviceability. Page 8

Exceptional TravelPerformanceHigh torque travel motors automatically shiftto provide increased tractive effort whenoperating in difficult ground conditions.Page 7

Smarter. Faster. Better.Inte-LXTM or Intelligent LX is the mostadvanced technology to date. Inte-LXTM

maximizes the balance between speed,power, and fuel efficiency. Page 4

First Electronic EngineControl in an ExcavatorThis results in increased responsiveness tothe job requirements; faster cycle times,increased fuel efficiency, cleaner andquieter. Page 6

Reduced Maintenance andExtended Component LifeThe Nephron® Filtration system meansless wear and tear on the hydrauliccomponents, reducing hydraulic systembreakdowns and maintenance costs.Page 8

Transportation Specifications (cont.)Catwalk

Weight:Left Front: 82 lbs. (37 kg)Left Rear: 73 lbs. (33 kg)

Dimension A: 1' 8" (.52 m)Dimension B: 8' 4" (2.55 m)Dimension C: 7' 3" (2.20 m)Dimension D: 1' 6" (.45 m)

AB C

D

Boom with Arm Cylinder and Piping

BOOM A B WIDTH WEIGHT

Excavator 7' 6" 28' 8" 4' 11" 17,725 lbs.(2.28 m) (8.73 m) (1.49 m) (8 040 kg)

Mass 8' 6" 24' 10" 4' 11" 16,578 lbs.(2.59 m) (7.58 m) (1.49 m) (7 520 kg)

A

BArm with Bucket Cylinder and Linkage

A

B

CARM A B C WIDTH WEIGHT

Mass 4' 9" 14' 5" 9' 9" 2' 5" 8,642 lbs.

9' 9" (2.98 m) arm (1.44 m) (4.40 m) (2.98 m) (.745 m) (3 920 kg)

Standard 4' 5" 17' 1" 12' 0" 2' 5" 8,223 lbs.

12' 0" (3.66 m) arm (1.35 m) (5.20 m) (3.66 m) (.745 m) (3 730 kg)

Standard 4' 3" 19' 5" 14' 7" 2' 5" 8,994 lbs.

14' 7" (4.44 m) arm (1.29 m) (5.91 m) (4.44 m) (.745 m) (4 080 kg)

Standard 4' 2" 23' 2" 18' 5" 2' 5" 10,119 lbs.

18' 5" (5.62 m) arm (1.28 m) (7.06 m) (5.62 m) (.745 m) (4 590 kg)

Boom Cylinder

A

B

C

Boom Cylinder: Weight: 1,763 lbs. (800 kg) Dimension A: 1' 3" (.40 m)Dimension B: 9' 7" (2.93 m)Dimension C: 1' 11" (.59 m)

Operating Weight:Standard Excavator: 174,600 lbs (79 200 kg)Mass Excavator: 174,600 lbs (79 200 kg)

SAE Net Horsepower: 444 HP (331 kW)Bucket Range: 2.47 - 5.91 cu. yd. (1.89 - 4.52 cu. m.)

Lexington, KentuckyLitho in USA 6/02 #LBX2074 (Supersedes #LBX2057)

® LBX and ® Link-Belt are registered trademarks. Copyright 2002. All rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifications.

Standard Equipment


Options• Inte-LXTM Computer System• Self-diagnostic system• Five selectable working modes• One-touch decelerator• Auto idling system• Auto idle start• Low idle up• Auto engine warm up• Auto power-up mode• Integral cylinder cushioning• Cushioned attachment control• Boom and arm holding valves• Free swing control• Auto power swing• Travel alarm• Nephron® filtration system• Low noise/low vibration cab floating

on 6 fluid filled mounts• Sliding/reclining, suspension cloth

upholstered seat with adjustable arm restsand lumbar support, retracting seat belt

• 3-position tilting consoles• 4th position on left console for entering

and exiting the cab also serves as controllock-out

• Illuminated LCD service monitor• Climate control heater and air conditioner• Hand grab rails both sides• Rear view mirrors, coat hook, storage

compartment

• Horn, interior lighting, AM/FM STEREOradio, digital clock, floor mat, cigarettelighter

• Safety glass front windows with automaticlock and intermittent rise-up windshieldwiper and washer, large LEXAN® rear/side windows

• Gate lock and gate lock lever (control lock-out device)

• Vandalism locks/guarding• Common key for cab & house doors, engine

hood, tool box, and fuel cap• Upper and lower undercovers• LC undercarriage• Easy Maintenance System (EMS)

Chrome pins and oil impregnatedbushings at all attachment locations

• 29.5" (750 mm) 2-Bar Grouser shoes• 27,560 lbs. (12 500 kg) counterweight

• Counterweight removal system(hydraulically controlled)

• Boom options27' 7" (8.40 m) Standard Excavator23' 9" (7.25 m) Mass Excavator

• Arms9' 9" (2.98 m) (Mass Excavator only)

12' 0" (3.66 m)14' 7" (4.44 m)18' 5" (5.62 m)

• Track35.5" (900 mm) 2-Bar Grouser Shoes43.3" (1100 mm) 2-Bar Grouser Shoes

• Auxiliary HydraulicsSingle ActingMulti-FunctionThumb

• Hose Burst Check Valves• Couplers (field install)

Hendrix Hydraulic CouplerEsco Multi-Pin Grabber

• Thumbs (field install)Esco Universal rigidEsco Hydraulic non-linkEsco Hydraulic non-link (for coupler)Esco Hydraulic link

Documents

Options - Link-Belt Cranes · • 4th position on left console for entering and exiting the cab also serves as control lock-out • Illuminated LCD service monitor • Climate control