OS 1744 WITH 4 CAMERA - Lorex Technology · 2016-02-08 · MENU QUAD/AUTOCA1 CA 2 CA 3 CA 4 TALK BUILT-IN QUAD OBSERVATION SYSTEM CAMERA1 CAMERA2 CAMERA3 CAMERA4 AUTO AL 2002. 10

Before operating the unit, please read this manual thoroughly and retain it for future reference

OWNER'S MANUAL

REAL TIME BUILT-IN QUAD OBSERVATION SYSTEMWITH REMOTE CONTROL17" B/W BUILT-IN QUAD & PAN/TILT CONTROL MONITORWITH 4 CAMERA

OS

174

4

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS.

Explanation of Graphical Symbols

This symbol is intended to alert the user to the presence of uninsulated, dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute risk of electric shock.

This symbol is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.

RISK OF ELECTRIC SHOCK DO NOT OPEN.

CAUTION

WARNING

CAUTION

WARNING

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DONOT REMOVE THE COVER (OR BACK) NO USERSERVICEABLE PARTS INSIDE FOR SERVICING REFER TO AQUALIFIED SERVICE PROFESSIONAL

1. READ INSTRUCTIONS-All the safety and operating instructions

should be read before the appliance is operated.

2. RETAIN INSTRUCTIONS-The safety and operating instructions

should be retained for future reference.

3. CLEANING-Unplug the monitor from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

4. ATTACHMENTS-Do not use attachments not recommended by the

monitor manufacturer as they may result in the risk of

fire, electric shock or injury.

5. WATER AND MOISTURE-Do not use this television equipment near

water (eg,bathtub,washbowl,kitchen sink,laundrytub, etc.)

6. ACCESSORIES-Do not place this monitor on an

unstable cart, stand or table. The monitor may fall,

causing serious injury to a child or adult, and serious damage to the

equipment. Wall or shell mounting should follow the manufacturer's

instructions, and should use a mounting kit approved by the

manufacturer.

6A. The monitor and cart combinations should be moved with

care. Quick stops, excessive force, and uneven surfaces may cause

the equipment and cart combination to overturn.

7. VENTILATION- Slots and openings in the cabinet and the back or

bottom are provided for ventilation, and to ensure reliable operation of

the monitor and to protect it from overheating. These

openings must not be blocked or covered. The openings should never

be blocked by placing the monitor on a bed, sofa, rug. or

other similar surface. This monitor should never be placed

near or over a radiator or heat register. This monitor/camera

should not be placed in a built-in installation such as a

bookcase unless proper ventilation is provided.

8. POWER SOURCES-This monitor should be operated

only from the type of power source indicated on the marking label. For

monitors designed to operate from battery power refer to

the operating instructions.

9. GROUNDING OR POLARIZATION-This monitor is

provided with a polarized alternating-current line plug(a plug having

one blade wider then the other). The plug will fit into the power outlet

only one way.

ALTERNATE WARNING-This product is equipped with a three wire

grounding-type plug. This plug will only fit into a grounding-type power

outlet.

I M P O R T A N T S A F E G U A R D S

I M P O R T A N T S A F E G U A R D S

10. POWER CORDS-Do not allow anything to rest on the power cord.

11. HEED WARNINGS-Follow all instructions marked on the monitor.

12. LIGHTNING-For added protection for this monitor during

a lightning storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet and disconnect the

antenna or cable system. This will prevent damage to the video

product due to lightning and power-line surges.

13. OVERLOADING-Do not overload wall outlets and extension cords as

this can result in a risk of fire or electric shock.

14. OBJECT AND LIQUID ENTRY-Never push objects of any kind into

monitor through openings as they may touch dangerous

voltage points or short-out parts that could result in a fire or electric

shock. Never spill any kind of liquid on the product.

15. SERVICING-Do not attempt to service this monitor

yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified

service personnel.

16. DAMAGE REQUIRING SERVICE-Unplug this monitor from the wall

outlet and refer servicing to qualified service personnel under the

following conditions:

A. When the power supply cord or the plug has been damaged.

B. If liquid has been spilled,or objects have fallen into the video

product.

C. If the video product has been exposed to rain or water.

D. If the video product does not operate normally by following the

operating instructions, adjust only those controls that are covered

by the operating instructions. A improper adjustment of other

controls, may result in damage and will often require extensive

work by a qualified technician to restore the video product to its

normal operation.

E. If the video product has been dropped, or the cabinet damaged.

F. When the video product exhibits a distinct change in performance -

this indicates a need for service.

17. REPLACEMENT PARTS-When replacement parts are required, be

sure the service technician has used replacement parts specified by

the manufacturer or that have the same characteristics as the

original part. Unauthorized substitutions may result in fire, electric

shock or other hazards.

18. SAFETY CHECK-Upon completion of any service or repairs to this

video product, ask the service technician to perform safety checks to

determine that the video product is in proper operating condition.

SAVE THESE INSTRUCTIONS.

NOTE:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuit to Part 15of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in aresidential installation This equipment generates, uses, and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radio communication. However there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to tryto correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio or television technician for help.

FCC CLASS A NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in theRadio Interference Regulations of the Canadian Department of Communications.

Le present appareil numerique n'emet pas de bruits radio electriques depassant les limites applicables aux appareilsnumeriques de la class A prescrites dans le Reglement sur le brouillage radio eiectrique edicte par le ministetre desCommunications du Canada.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.

The users manual or instruction manual for an intentional or unintentional radiator shall caution theUser that changes or modifications not expressly approved by the party responsible for compliancecould void the user authority to operate the equipment.

WARNING:TO PREVENT DAMAGE WHICH MAY RESULT

IN FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

FCC CLASS A NOTICE

CERTIFICATION:This unit complies withDHHS rules 2 cfrsubchapter J and FCCrules 47 c f r par t isapplicable at date ofmanufacture.

RISK OF ELECTRIC SHOCK DO NOT OPEN.

CAUTION

TABLE OF CONTENTS

Introduction ........................................................................................... 3

Precaution Before Installing or Using the System ................................. 3

Description of ControlsMonitor Unit ............................................................................................ 4-9Camera Units .......................................................................................... 10-12

InstallationCamera Units ...........................................................................................13-15Monitor Unit .................................................................................... 16-17

Wiring Diagram ..................................................................................... 18

Trouble shooting guide ......................................................................... 19

Specifications Monitor Unit ............................................................................................ 20Camera Unit ........................................................................................... 21-23

Accessories .......................................................................................... 24-25

Care and Maintenance ......................................................................... 26Warranty ............................................................................................... 27

page

This OBSERVATION SYSTEM will give you added security and comfort for many years. It is easy to install in almost anywhere you need audio/ video surveillance. To safely use all the high technical functions of the unit, please read the installation and operating instruction in this manual, and keep it for the future reference. FEATURES

• Built- in Real Time Quad Processor • 2 Way audio between monitor and cameras • Pan+ Tilt controls for dome camera • Motion sensor capability of up to 20fit distance • Record and review the images with a standard VCR or Time Lapse Recorder • On Screen Date/Time/Camera ID Display • Built-in alarm Inputs /Outputs

SYSTEM CONTENTS • 17” B/ W Quad + Pan/ Tilt monitor • 2 B/W Motion sensor cameras with built-in speaker • 1 B/W High resolution camera with built-in speaker • 1 B/ W Pan/ Tilt dome camera without built-in speaker • 4 - 65 ft camera connection cables • Remote control

Read the following precautions before installing or using the system 1. Choose an ideal location for the camera so that the lens won't be exposed to any direct light source. The camera unit must also be protected against moisture and vibration. 2. The monitor should only be operated with the correct power source indicated on the adaptor. 3. Check the system for operation prior to installing the unit.

4. Be extra careful not to scratch the camera lens. 3

INTRODUCTION

4

DESCRIPTION OF CONTROLS & OPERATION

VOLUME V-HOLD.H-POSI.BRIGHT CONT.

VCR

123456

7 8 9 10 111213

MIC POWER

PUSH

MENU CA1 CA 2 CA 3 CA 4 TALKQUAD/AUTO

BUILT-IN QUADOBSERVATION SYSTEM

CAMERA1 CAMERA2

CAMERA3 CAMERA4

AUTO AL

2002. 10. 28. 12:32:26

15

14

Front View

A. Monitor Unit FRONT VIEW

1. POWER ON/OFF SWITCH (STANDBY)By pushing the standby button the image and sound on the monitor can beswitched ON and OFF. The alarm functions also remain active.

2. TALK BUTTONPress and hold this button to talk through to the camera. Release it to receive audio. When you press the “TALK” button in the quad mode, the Monitorwill display the letter “T”. The channel being displayed, “T” means it is ready to transmit the audio. To transmit, press the selected channel button. In full screen mode, press the“TALK” button to transmit the audio.

3. CAMERA-1,2,3,4 BUTTONSPress each button to monitor the desired channel.

4. QUAD / AUTO SWITCHING BUTTONThis button is used to change between the QUAD and AUTO modes. Pressing this button changes the screen from QUAD display to full screen display. The monitor will automatically switch between the four camera locations. Press this button to return to QUAD display.Quad function - Displays up to four cameras on the screen at one time. The pictures are reduced in size to one-fourth of the screen. The screen is divided into four quadrants. Auto function - Selecting the system in the auto switching mode, with more thanone camera will automatically display the locations one by one. When turning the system on, Camera 1 will operate automatically. After turning on the system, you can program the Auto Switching sequence of the cameras being viewed. By pressing the Auto button again the automatic switching function is switched off. NOTE : AUTO appears on the screen.


5

5. MENU(ON SCREEN DISPLAY) This monitor provides an on screen programming function including camera identification, sequence, scan dwell time, alarm reset time and time/date.SETTING UPTo enter the on-screen programming, press the MENU button located on the front of the monitor. The main menu, as identified below will appear.

NOTE: USE THE (UP / DOWN) AND (LEFT / RIGHT) ARROW BUTTONS LOCATED ON THE FRONT OF THE MONITORTO MOVE AROUND THE SCREEN.

1) TITLE SET (CAMERA IDENTIFICATION) Press the MENU button to enter the title set (Camera Identification) mode. The Cursor button will automatically flash over the first letter in Camera1. Use the (UP / DOWN) and (LEFT / RIGHT) buttons to name the camera location (EG. FRONT, COUNTER, etc) A total of eight characters are available. When complete, press the MENU button to proceed to cameras 2,3 and 4. Press the MENU button until you exit, and return to the main menu. You can turn the monitor display ON or OFF.

2) SEQUENCEThis function is used in the AUTO mode. The camera will automatically rotate between the four camera locations in AUTOmode. The monitor has been defaulted to a 1-2-3-4-Q setting. To change this setting proceed as outlined below. Otherwise proceed to SCAN DWELL TIME. To change the sequence of camera setting, press the menu button. Use the (UP / DOWN) and (LEFT / RIGHT) buttons to change the camera sequence. When complete, press the MENU button to exit.

3) SCAN DWELL TIMEThis function is used in AUTO Mode to automatically rotate from one camera to another. The setting is defaulted to 1 second, but can be adjusted between 1-60 seconds. To change the Scan Dwell time, proceed as outlined below. Otherwise proceed to ALARM RESET TIME• Use the (UP / DOWN) arrow keys to go to SCAN DWELL TIME selection.

• Press the MENU button to scan dwell time. Use the (UP / DOWN) arrow keys to adjust the time. When complete, press the MENU button to exit.

4) TIME / DATETo adjust the time or date, proceed as follows: Use the (UP / DOWN) arrow keys to go to proceed to the TIME/DATE menu.Press the MENU button to enter this setting and use the (UP / DOWN) arrow keys to change the settings. When complete, press the MENU button to exit the TIME/DATE menu. You can turn the monitordiplay ON or OFF.

( MAIN MENU )1. TITLE SET2. SEQUENCE3. SCAN DWELL TIME4. TIME / DATE5. ALARM MODE6. EXIT


6

5) ALARM MODEWhen motion / movement is detected at the camera location,the monitor will display in full-screen for this camera. The letters AL will appear at the top right corner of the screen and the camera location where the alarm has taken place will appear in the top left hand corner. An Alarm buzzer will sound to alert you of an emergency situation. This alarm will sound for five seconds. 1. Defaulting alarm time procced 15 seconds, and used to adjust

selecting defaulting time. 1) Used to adjust selecting time schedule, allowing to switch turn

ON/OFF the monitor display of each channel. 2) Pressing “Alarm ON/OFF default” goes to turning off.

2. Alarm operation1) With one channel operation, the channel with which the alarm has

taken placed will operate in full screen only. If there is more than two channels operating, the letter AL will appear.

2) When the signal is cut off from the Camera, you can see the “LOSS” in quad display, and an Alarm buzzer will sound to alert you of an emergency situation.Use the (UP / DOWN) arrow keys to go to the ALARM RESET TIME MODE selection.Press the MENU button to enter this setting. Use the (UP / DOWN) arrow keys to change the setting. When complete, press the MENU button to exit ALARM RESET TIME MODE.

When the alarm function is used, the monitor will automatically switch to full screen display when motion/movement is detected. The user will be alerted to motion being detected for 1-90 seconds (see alarm reset time). At the end of this time, the monitor will automatically switch back to the previous mode in which it was originally set. Should additional triggers be received during the second period, the systemwill automatically switch to the relevant cameras and continue the

warning sound. Optional recording devices (VCR. time lapse VCR, Eventrecorders) can also be connected to the monitor to record key events.

Remark : The monitor installed SENSOR input / PIR sensor camera will always switches to the camera image of the last-received alarm. Sensor inputs/outputs switches allow you to control optional sensor accessories directly to the monitor. The alarm trigger device should be coneected to the monitor. The alarm trigger device should be normally open. The alarm output can be either normally open or closed.

6. MICROPHONEPick up sound around the monitor.

7. VOLUME CONTROL KNOBTurn on the VOLUME control up or down to reach the desired volume.

8. VERTICAL HOLD CONTROL KNOBUsed to adjust the VERTICAL synchronization.

9. HORIZONTAL POSITIONUsed to adjust the HORIZONTAL stability of the screen.

10. BRIGHTNESS CONTROL KNOB Used to adjust the BRIGHTNESS of the screen.

Normally open+ DC 12V(MAX 100mA)_ GND

SENSOR IN ALARMOUT

C1 C2 C3 C4

11. CONTRAST CONTROL KNOBUsed to adjust the CONTRAST of the screen.

12. VCR ON/OFF SELECTOR Press this button to playback the video signal from VCR. Press it again to stop the video signal. (When the VCR button is “ON”, the red LED will display)VCR Recording Reviewing Method1) Connect the monitor to the VCR and press the RECORD button

on the VCR to start recording the pictures. (NOTE: Ensure your VCR is set to auxiliary mode. Consult your VCR Owner’s manual for details.)

2) To review the recorded pictures, press the VCR button on themonitor and then the PLAY button on the VCR.

13. PAN/TILT ON/OFF SELECTORThis feature allows you to control the dome camera. The motorized PAN/TILT camera allows you to change the camera direction, either up or left to right depending on your prefernce.• Use the (Left/Right) arrow keys to rotate the camera 355

horizontally. Use the (Up/Down) arrow keys to rotate the camera85 vertically.

• In the Quad Mode, pressing the Pan/Tilt key will diaplay the letter “P” on the monitor. The letter “P” will appear in the upper left hand quadrant for Camera 1. Pressing the Pan/Tilt key again will place the letter “P” in the second quadrant or Camera 2, and so on, for Camera 3 and 4.

• For the Full Screen Mode(Pan/Tilt), press the Quad/Auto button to switch it back to full screen. Press the individual camera channel 1,2,3or 4, depending on the camera channel the Pan/Tilt Dome camera is connected to. Finally, press the Pan/Tilt button to activate the Pan/Tilt feature. The letter “P” will appear on the screen. use the left/right and

up/down arrow keys to rotate the camera.14. FREEZE ON/OFF SELECTOR

Stoppage of image or playback is allowed only in Quad or Full Screenmode. • In the Quad Mode press the Freeze button to stop the image, and press it again to release or unfreeze the image. The letter “F” will be appear on the display screen. Press the freeze button and then press the individual camera channel 1,2,3 or 4 to freeze the image on that channel. Press the camera channel again to unfreeze the image.

• For the Full Screen Mode, you must press the Quad/Auto button to switch it back to full screen. Press the individual channel to take it out of the AUTO mode. Press the individual channel again(1,2,3 or 4) to freez the camera image, and press again to unfreeze it.

15. REMOTE CONTROL SENSORTurn on the main power, and push the stand-by button. Using the remote control gives you full switcher functions on the front panel of the monitor (except for the power function).


7

MENU

QUADVCR

1

3

5

54 6

87 9

0

QUAD

CA1

CA2

CA3 CA4

AUTO

VCR PAN/TILT FREEZE

CAMERA 1~4

AUTOFREEZE (QUAD)

PAN/TILT

2

4

6

7

MENU

Remote controller

2 “AAA” Batteries requiredfor remote control

REAR VIEW

16. CAMERA INPUT JACKSInputs to connect camera.

17. VIDEO INPUTReceives video signal from VCR or other recording devices.

18. AUDIO INPUTReceives audio signal from VCR.

19. AUDIO OUTPUTTransmits audio signal to audio amplifier. Also used in recording on VCR.

20. VIDEO OUTPUTTransmits video signal from a camera to another monitor. Also used in recording on VCR.

21. AC POWER CORDPlug the supplied power supply cord into the monitor, the other end to an outlet.

22. SLAVE MONITOR OUTPUTAudio and video output for slave monitor. Connect via double male to doublemale phone leads of required length. NB: Maximum recommended distance between master and slave monitor is 65ft.

23. ALARM FUNCTION INPUT / OUTPUTSSwitches alarm function on/off NB alarm function is set to on position upon activation of the monitor via power switch.


8

C1 C2 C3 C4

SENSOR IN ALARM OUT CA1 CA2 CA3 CA4

CAMERA IN PUT

1623 2421 17 19 20 22

25

26

18

CA1 CA2 CA3 CA4

A)B+B)Audio inC) Camera audio AMP:B+,

PAN/TILT control signalD)Video inE)Audio outF)N.C

Rear View

D

E

F

A

B

C


9

24. MAIN POWER SWITCHThis switch is used to turn ON or OFF all power to the monitor.

25. LOOPING OUTPUTS 1~4These are looping outputs for cameras, one through four. Can be used to display cameras on a separate monitor or recorder.

26. BNC CAMERA INPUTS 1~4These inputs are used for standard cameras with BNC type connectors.


A. Motion Sensor Camera Unit

1)

3)

2)

Front View

4) 5)

a. b. c. d. e.

Front View

1. MICROPHONEPick up sound around the camera

2. CCD CAMERAA LENSDelivers a clear detailed pocture to the Monitor (auto-focus, auto-iris)

3. MONITOR SENSORSensor detects movement within a 6 meter range

4. CABLE CONNECTOR COVERRemove the 2 screws to release the Cover and connect the cable

5. CABLE CONNECTORThe camera cable will plug into this Connector. The following color coding for the wires are listed below.a. Black (Motion Sensor signal)b. Yellow (Microphone audio signal)c. Black (Ground for A/V signal)d. White (Camera video signal)e. Red (Power supply input)

10


1. CCD CAMERA LENSTurn the front ring of the lens to obtain the focus desired.

2. MICROPHONEPick up sound around the camera.

3. ALARM TERMINALConnect an optional alarm device to this terminal.

4. MONITOR INPUT JACKConnect to cable the monitor.

5. BRACKET

6. SPEAKERDeliver the sound from the monitor.

B. High Resolution Camera Unit

Front View Rear View

1

26

5

TO MONITOR

4

3TERMINAL

IN Alarm input (normally open)GND GroundB+ Power output +12V DC 100mA

IN

GND

B+

TERMINAL

11


107

C. Pan/Tilt Dome Camera Unit

Adaptor plate

fl3 x 20 screw

Hook

Base (hold base when you twist to attach the dome to adaptor plate)Swivel

Bubble

1. CCD Camera Lens - Delivers a clear detailed picture to the monitor2. Pan/Tilt Mechanism - Up/Down & Left/Right movements, giving you 3553. Din Plug Connector - Connect the 65 ft cable from this connector on the dome camera to the monitor

(1) (2)

(3)

12

INSTALLATION

A. Motion Sensor Camera UnitInstalling the mounting bracket/rain cover

PILOT HOLE

HORIZONTAL MOUNTING SURFACE

MOUNTING BRACKET

VERTICALMOUNTINGSURFACE

MOUNTING SCREW

Installing the mounting bracket/rain cover

MOUNTING BRACKET

CAMERA

MOUNTING SURFACE

1.The camera mounting bracket can be installed on any vertical or horizontal flat surface using the two mounting screws provided (fpr the best viewing angle install between 2 to 4 meters from the ground)

2.Once the mounting bracket is secure on the wall or ceiling, remove the camera cable cover by taking out the two small screws with a Philips screwdriver

3. Attach the camera to the privot bolt on the mounting bracket by screwing it on by hand4. Plug the camra cable into the connector on the back of the camera and run the other end of the cable back to the monitor5. Replace the cover on the back of the camera

13

INSTALLATION

B. High Resolution Camera Unit

Permanent installation using pedestal stand.

CAUTION : Keep camera installed away from direct sunlight. Also avoid places where humidity is high or where the camera is not protected from rain. The mounting bracket must be attached to a structural object such as a wall stud or ceiling rafter using suitable fastener. Do not touch the glass of the lens. This could damage the delicate coating on its surface. If the lens has to be cleaned, use a special lens cleaning tissue available at any camera store.

14

1. Attach the Pedestal using 4 screws. 2. Attach the Camera onto the Pedestal and tighten the thumb screw.

INSTALLATION

A

105

10510

7

FRONT VIEW TOP VIEW

Electrical power is not connected to the dome and observation / quad monitor during installation.

Adaptor plate

fl3 x 20 screw

Hook

Base (hold base when you twist to attach the dome to adaptor plate)Swivel

Bubble

To install the dome camera on a ceiling or wall follow these procedures :

1. Twist open the clear dome cover in a CCW direction to reach inside the dome camera (Turn at the swirel section of the camera).

2. Place the dome camera on a flat surface.

3. Run the 65 ft DIN cable (Included with the dome camera) from the wired lead of the dome camera to the back of the monitor, in one of the camera inputs labeled, “CH1, CH2, CH3 or CH4”

4. Attach the adaptor plate on the ceiling or wall, using the 3 screws provided (Ø3 X 20 screw)

5. Twist the base of the dome camera to the adaptor plate on the ceiling or wall.

Do not hold clear bubble or swivel, when you attach the dome on the adaptor plate.

15

C. Pan/Tilt Dome Camera Unit

C. Monitor Unit

1-4 Camera connections

Using the provided cables, connect the camera to the monitor as shown in the diagram below.

C1 C2 C3 C4


CAMERA IN PUT

1 2 3 4

CA1 CA2 CA3 CA4

1. Camera 1 TerminalConnect camera 1 cable to this terminal.




INSTALLATION

AC Power Cord

16

Monitor with BNC cameras

The observation monitor may be installed with a standard BNC output security camera. Connect one end of the BNCvideo cable to the output of the camera and the other end of the BNC video cable to the BNC camera input on the rear of the observation monitor.

INSTALLATION

AUDIO/ VIDEO JACK CONNECTIONS.

Refer to the following connection method, when connecting to the VCR

INSTALLATION WITH A TIME- LAPSE RECORDER.

Monitor VCR Terminal

Video OUT Video INAudio OUT Audio INVideo IN Video OUTAudio IN Audio OUT

Monitor Back view TIME lapse recorder

Video 1 OUT Video INAudio 1 OUT Audio INVideo IN Video OUTAudio IN Audio OUT

SLAVE Monitor

Video 2 OUT Video IN Audio 2 OUT Audio IN

NOTE: The cable for this connection is not supplied with the unit. An "RCA" type cable is required.

NOTE: Ensure your VCR is SET to AUXILIARY (AV) MODE. Consult your owners manual for details

17

NOTE: Do not use RCA jack to connect any cameras.

WIRING DIAGRAMS

WIRING Connections

C1 C2 C3 C4


CAMERA IN PUT

CAMERA1

CAMERA3

CAMERA4

CAMERA2

CA1 CA2 CA3 CA4

CCD CAMERA

CCD CAMERA

18

TROUBLE SHOOTING GUIDE

19

Problem

Multiple image in picture

Picture rolls up or down

Too dark or bright picture.

NO POWER

Poor picture quality

Picture but no sound

Sound but no picture

Shrinking picture

Monitor

Check Point

Readjust the VERTICAL Holdcontrol knob.

Readjust the VERTICAL Holdcontrol knob.

Readjust the CONTRAST orBRIGHTNESS controls.

Check for AC connection.

Clean the camera lens.Readjust the CONTRAST or

BRIGHTNESS controls.

Adjust the VOLUME control knob.

Readjust the CONTRASTor BRIGHTNESS controls.

Check the condition of thePOWER source.

Before calling service, check the following points for possible misuse.

SPECIFICATIONS

Monitor

Picture tubeHorizontal resolutionTV signal formatCamera inputVideo input (VCR) Video outputMax. wiring distanceConnection Camera switching timeOutput slave monitor A/VAlarm inputAlarm outputAlarm time (OSD menu) Power sourceDimensionsWeightAmbient temperature (operating/storage) Cabinet humidity (operating/storage) Cabinet

17" B/W 90° deflection angle750 lines at center

EIA : 700 lines, 60 Hz 1.0V p-p 75Ω terminated1.0V p-p 75Ω terminated1V p-p (75Ω load) 100 m 6 pin DIN JACK / BNC Connector1 ~ 60 seconds (Adjustable) RCA connectors8 pin push type4 pin push type1 ~ 90 Seconds (Adjustable)100-240V~, 50/60Hz, 0.7A161/4”(W) X 141/2”(D) X 151/4”(H)mm32 lbs14°F ~ 122°F10% ~ 90%Metal with plastic front

20

SPECIFICATIONS

21

High Resolution Camera Unit

Image SensorEffective Picture ElementsHorizontal Drive FrequencyVertical Drive FrequencyVideo OutputAudio Output

Iris, Automatic Control by Electronic SystemAngle PictureLens MountAlarm inputs Power RequirementsMinimum Light lluminanceOperating TemperatureDimensions

1/3" CCD B/WEIA : 492(V) X 512(H)EIA : 15.75 KHz / CCIR : 15.625KHz EIA : 60Hz / CCIR : 50Hz1V p-p 75 ohm200 mV

Horizontal 74° Vertical 55°C/CS mount3 PIN terminals12V 200mA, Maximum 2.4W0.1 Lux-10°C ~ +50°C (14°F ~ 122°F)50(W) X 120(D) X 50(H)mm

SPECIFICATIONS

Motion Sensor Camera Unit

Image SensorPicture ElementsResolutionMin. IlluminationVideo/Audio OutputS/N RatioOperating Temp.DimesionsSensor rangeRange of the motion sensor

1/3” B/W CCD251,000 Pixels>380 TV Lines1 Lux1V p-p (75 ohm)>50 dB-10°C ~ +50°C118(W) X 95(D) X 110(H) mm6 MetreHorizontal 90° Vertical 80°

22

SPECIFICATIONS

Power sourceImage sensorActive pixelsImage sensor areaSignal to noiseElectronic irisSynchronization Signal formatVideo outputAudio outputAmbient temperatureAmbient humidityResolution Min. illumination LensPower consumptionDimensions

12V 1/3” interline transfer CCD, B/WEIA : 512(H) X 492(V) 4.8(H) X 3.7(V)mm46dB1/100.000 secInternalEIA : 525 lines, 2:1 interlace1.0V p-p (75 ohms) 600 ohms line level-10°C ~ +50°C0-96% Non-condensing> 380 TV lines1 Lux3.6mmMAX 2.4W126 X 95 mm

Pan/Tilt Dome Camera Unit

23

Because this product is subject to continuous improvement, the manufacturer reserves the right tomodify its design and specifications without notice and without incurring any obligation. E & O.E.

ACCESSORIES

Standard Accessories

Screws Pedestal stand/Mounting Bracket6P Cable(20m)

24

Remote Control

54 6

87 9

0

QUAD

CA1

CA2

CA3 CA4

AUTO

VCR PAN/TILT FREEZE

MENU

ACCESSORIES

25

Optional Accessories

Bullet Camera Dome Camera Mounts

Extension cable

High Power Night Vision Camera

Weather proof housingVCR

STOP/EJECT

POWER

REC

DIGITAL CCD CAMERA

CARE AND MAINTENANCE

Your video observation system is an example of superior craftsmanship. Followingthese precautions will give you many years of solid performance and enjoyment.

Keep your monitor & camera dry. If it does wet,wipe it dry immediately.

Use and store your unit in normal temperature environment.Extreme temperatures can shorten the life of electronic devices.

Handle the monitor carefully. Dropping it can causeserious damage to the unit.

Occasionally, clean the unit with a damp cloth to keep it lookingnew. Do not use harsh chemicals, cleaning solvents, or strongdetergents to clean the unit.

Keep the unit away from excessive dirt and dust.These can cause premature wear of parts.

Note : All specifications subject to change without notice. E & OE.

26

Home Sentinel warrants this home security product ("The Product") to be free from defects in material andworkmanship for a period of one year from date of purchase. This warranty does not cover any expenses incurredin the removal and reinstallation of the product. This warranty is offered to the original purchaser of the productonly.

If the product should prove defective within the warranty period, return the product postage prepaid to HomeSentinel, along with your dated sales slip or other proof of purchase which will establish your eligibility for thewarranty. Home Sentinel will at its option, replace or repair the product free of charge and return the product toyou postage prepaid. This warranty does not apply to the product which has been damaged, misused, altered orrepaired by anyone other than a Home Sentinel authorized service facility.

ANY IMPLIED WARRANTIES INCLUDING FITNESS FOR USE AND MERCHANTABILITY ARE LIMITED INDURATION TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE, AND NO PERSON ISAUTHORIZED TO ASSUME FOR HOME SENTINEL ANY OTHER LIABILITY IN CONNECTION WITH THE SALEOF THE PRODUCT. HOME SENTINEL EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTAL ANDCONSEQUENTIAL DAMAGES CAUSED BY THE PRODUCT. THE REMEDIES PROVIDED UNDER THIS WARRANTYARE EXCLUSIVE AND IN LIEU OF ALL OTHERS.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state orprovince to provinces Some states/provinces do not allow limitation on how long warranty lasts, so the abovelimitation may not apply to you. Additionally, some states/provinces do not allow the exclusion of limitation ofconsequential or incidental damages, so the above limitation or exclusion may not apply to you.

WARRANTY

27

Documents

OS 1744 WITH 4 CAMERA - Lorex Technology · 2016-02-08 · MENU QUAD/AUTOCA1 CA 2 CA 3 CA 4 TALK BUILT-IN QUAD OBSERVATION SYSTEM CAMERA1 CAMERA2 CAMERA3 CAMERA4 AUTO AL 2002. 10