Upload
hari-prasad
View
221
Download
0
Embed Size (px)
Citation preview
8/11/2019 OS and Program Upload to Datalogger
1/14
STANDARD OPERATING PROCEDURE FOR INSTALLING AN OPERATING
SOFTWARE AND A PROGRAM UNTO A CR2xx DATALOGGER
Compiled by: Daiel Di!be"
S#pe"$i%ed by: D"& 'o( C& Cepe)e
No$embe" * 2++,
8/11/2019 OS and Program Upload to Datalogger
2/14
Table o- Co.e.
I& E/#ipme.%&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&0
II& Uploadi! Ope"a.i! So-.1a"e .o CR2+ Da.alo!!e"&&&&&&&&&&&&&&&&&&&&&&&&&,
III& Uploadi! p"o!"am .o CR2+ Da.alo!!e"&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&32
I4& Co)l#%io&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&35
2
8/11/2019 OS and Program Upload to Datalogger
3/14
I& E/#ipme.%
The following equipments are required:
Figure 1. CR205 Datalogger
Figure 2. Batter
!
8/11/2019 OS and Program Upload to Datalogger
4/14
Figure !. "aptop#Des$top %omputer
Figure &. '(B to R()2!2 *ridge %a*le
&
8/11/2019 OS and Program Upload to Datalogger
5/14
Figure 5. Conne%ting wires for power suppl
5
8/11/2019 OS and Program Upload to Datalogger
6/14
II& Uploadi! Ope"a.i! So-.1a"e i.o .(e Da.alo!!e"
Conne%t R()2!2 port from the datalogger to a serial port on our %omputer.
+anuall download the data to ensure that up to date data is %olle%ted.from the
datalogger using ,a$%om- ,C 200 !.2 or loggernet software.
+a$e sure that all softwares are dis%onne%ted and %losed after downloading the
data from the datalogger.
/pen Dei%e Configuration 'tilit software as seen *elow in Figure .
+a$e sure that the appropriate serial port is sele%ted in the left panel- %onne%t to
datalogger * %li%$ing on %onne%t shown on the left side of Figure *elow.
+a$e sure that power is dis%onne%ted from the datalogger.
Figure . (%reen of Dei%e Configuration 'tilit (oftware
8/11/2019 OS and Program Upload to Datalogger
7/14
There are fie %ontrol panels: Deploment- "ogger Control- Data +onitor- (end
/( and (ettings ditor as shown *elow in Figure 3.
Deploment is used to set the ,a$*us address of the datalogger. 4t is also
used to set the RF power mode- hop sequen%e- networ$ and address.
"ogger Control sets the %lo%$ on the datalogger. 4t is also used to send
program unto the datalogger.
Data +onitor displas the data on the datalogger in three settings with
names Data- ,u*li% and (tatus.
(end /( is used to download operating software unto a datalogger.
(ettings ditor spe%ifies the ersion of the operating sstem.
Figure 3. (%reen of software after %onne%ting to datalogger
Cli%$ on (end /( as shown in the s%reen *elow.
3
8/11/2019 OS and Program Upload to Datalogger
8/14
Figure . (%reen of software during uploading /( to datalogger
Cli%$ on start *utton as shown a*oe. The s%reen will *e displaed for ou to
sele%t the folder to upload the operating software.
4n the resulting file open dialogue *o6- sele%t the file that has to *e sent as an
operating sstem 7tpi%all- CR266 operating files hae a .a&! e6tension8.
8/11/2019 OS and Program Upload to Datalogger
9/14
Figure 9. (%reen of software when sear%hing for /perating (stem in folder
fter ou hae %li%$ open *utton in the file open dialogue- appl power to the
datalogger.
The operating sstem will now *e sent to the datalogger. This has to *e allowed to
run to %ompletion. Can%eling the operation %an leae the datalogger without a
alid operating sstem to run.
9
8/11/2019 OS and Program Upload to Datalogger
10/14
Figure 10. 'ploading /perating (stem to CR205 datalogger
/n%e the /perating (stem has *een sent to the datalogger- its program will *e
%leared and all of it as settings will *e reset to their default alues. 4f the
datalogger was preiousl set up- ou will need to %onne%t to it and edit its
settings to restore the preious set)up.
10
8/11/2019 OS and Program Upload to Datalogger
11/14
Figure 11. Completion of the upload of the /perating (stem to the datalogger
/n%e the /perating (stem 7/(8 has *een sent to the datalogger- if ou desire to
remoe power from the datalogger- ou must wait at least 10 se%onds *efore
dis%onne%tion. This will gie the datalogger the time that it needs to update the
flash memor lo%ations.
11
8/11/2019 OS and Program Upload to Datalogger
12/14
III& Uploadi! P"o!"am .o .(e da.alo!!e"
From the dei%e %onfiguration utilit software open logger %ontrol as shown on
the s%reen *elow.
Figure 12. (%reen of (oftware when uploading program to datalogger
Cli%$ on send program to open the dialogue *o6.
12
8/11/2019 OS and Program Upload to Datalogger
13/14
Figure 1!. (%reen of (oftware when sear%hing for program in folder
Cli%$ on the program to *e uploaded and %li%$ open. nsure that the program has
*een %ompiled *efore uploading. ;ormall the program %omes a long with a
program %ompiler. The program %ompiler %ompiles the program in the right order
into the datalogger.
1!
8/11/2019 OS and Program Upload to Datalogger
14/14
I4& Co)l#%io
4t is alwas re%ommended that operating sstem in dataloggers are updated to aoid
pro*lems with downloading of data. lso- the softwares used to download data from
dataloggers should *e updated %onsistentl. This improes data %olle%tion.
1&