Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
PW54 / PS54 PW55 / PS55 PS53 PW97 PW51
ABS ABS ABS PE ABS
� �-30°C/+50°C -30°C/+50°C -30°C/+50°C -30°C/+50°C -10°C/+50°C
440 VAC 440 VAC 440 VAC
MM MM
LD LD LD
PA51
PA52 �PW56 � �PW58 �PW47 / PS47 � � �PW42 / PS42 �
EN 397: 2012Industrial Safety HelmetsMandatory tests:• Impact* : Energy spread to the head form must not exceed 5 kN after the fall of an object of 5 kg at 1m high.
• Penetration* : The tip of the test mass used (3 kg from 1m height) must not come into contact with the skull.
• Flammability : The helmet is exposed to a flame and it must not burn with flame emission more than 5 seconds after removal of the flame.* Impact and penetration tests are performed at room temperature, at +50 °C and at -10°C.
Optional tests:• Resistance at extreme temperatures:testing impact and penetration are performed at +150 °C, at -20°C or -30 °C temperatures.• Electrical properties:Protects against a short accidental contact with electric leads under voltage up to 440 Vac.• Lateral deformation:Protects against lateral compression. The maximum deformation of the helmet should be ≤40 mm (LD).• Molten metal splashes:The helmet is not deformed or penetrated by splashes of molten metal (MM).
EN 50365: 2002Insulating helmets for use on low voltage installations
This standard is for helmets used for working live or close tolive parts on installations not exceeding 1000 V a.c. or 1500 V d.c. Testing to EN50365 exceeds testing under EN397 for electrical properties.Marking: double triangle + class +batch number.
ANSI/ISEA Z89.1: 2009American National Standard for Industrial Head Protection
This standard describes Types and Classes, testing and performance requirements for protective helmets. These include recommended safety requirements for authorities considering the establishment of regulations or codes concerning the use of protective helmets.
TYPE I - Hard hats are designed only to withstand top impactsTYPE II - Hard hats designed to withstand impacts from the top and the side.Class C - Conductive Helmet = the hard hat will not protect the wearer from electrical hazards.Class G - General Helmet = helmet can withstand an electrical current up to 2,200 volts.Class E - Electrical Helmet = helmet that providing the highest level of electrical protection, withstanding currents up to 20,000 volts.
Head ProtectionPW rapidly expanding head protection product range aims to benefit our customers by combining the most updated styles and standards in head protection, irrespective of job or location.A wide selection of compatible accessories is also available. A full explanation of features and performances are given in order to help you make a more informed choice.
FEATURES
Shell material
Harness material Polyamide (textile)
Polyethylene(plastic)
Polyamide (textile)
Polyethylene(plastic)
Nylon (textile)
Adjustment Wheel Ratchet Wheel Ratchet Wheel Ratchet Wheel Ratchet Buckle
Ventilation
EN 397
Temperatures
Electrical Properties (440Vac)
Molten Metal
Lateral Deformation
EN 50365 Electrical Insulation (1000Vac/1500Vdc)
Range Selection Help With Choice
468
AW15_PPE-FINAL.indd 468 04/06/2015 14:56
ID10
ID12
PA51
ID11
PA52 PW53
100 100 500
PW56
12
LD
PW98
H: 32 dBM: 26 dBL: 19 dB
SNR29dB
PS50 PW50 PW57 PS52 PW98
PP PP PP PP ABS
� �-10°C/+50°C -10°C/+50°C -10°C/+50°C -10°C/+50°C -30°C/+50°C
440 VAC 440 VAC
LD LD LD
� �� �
� � ��
� � �
Polyamide (textile)
Polyethylene(plastic)
Polyethylene(plastic)
Nylon(textile)
Polyethylene(plastic)
Buckle Buckle Buckle Wheel Ratchet Wheel Ratchet
ID Holder
In Case of Emergency (ICE) stickers for accident victims gives on-site instant access to victims potential lifesaving information and enables emergency contacts be quickly notified of the situation 24/7.
PVC Yellow
Medical Information Contact
Offers immediate identification of the worker with medical information that could ultimately save the life of the worker in accidents and emergencies. Language free with instantly recognisable icons for easy and global recognition.
PVC Red
Safety Helmet Harness Ratchet
Polypropylene Clear
Adjustable headband 52-62cm
Slip Ratchet Safety Harness
Polypropylene
Clear Adjustable headband
52-62cm
Universal Emergency ID Emergency ID using universal images to ensure that vital emergency information can be easily identified in the event of an accident.A window displays user’s name.
PVC Yellow
Chin Strap
Suitable for PW50, PW51, PW57 and PS50.
Nylon, PP Black
Endurance Visor Replacement EN 166 1 B 9
Suitable for PW54, PS54, PW55 and PS55.
Polycarbonate Clear
Forestry Combi Kit EN 352-3EN 166 3BEN 1731 FEN 397 -30°C/+50°C, LDANSI/ISEA Z89.1 TYPE I CLASS G
ABS Helmet, Mesh Visor, ABS/Polystyrene Ear protector.
Orange, Adjustable 56cm - 62cm
Pete
r Jon
es
100010
600100
1
800100
1
800100
1
AW15_PPE-FINAL.indd 469 04/06/2015 14:56
PW54
PW55
PS54
PS55
20
AS AF LD
20
AS AFLD MM
20
LD MM
20
LD
NEWCOLOUR
NEWCOLOUR
CECATIII
CECATIII
Endurance Plus Visor Helmet EN 50365 CLASS:0EN 397 -30°C/+50°C, MM, LD, 440VEN 166 1 B 9ANSI/ISEA Z89.1 TYPE I CLASS E
ABS shell helmet, textile comfort harness 6 points, wheel ratchet adjustment, adjustable size 56-63 cm. Sweat band and chin strap included . Sold with retractable clear visor PW56 included.Spare parts available.
ABS, Polycarbonate
Blue, Orange, Red, White, Yellow Adjustable 56-63cm
Endurance Visor Helmet EN 166 1 B 9EN 397 -30°C/+50°C, LDANSI/ISEA Z89.1 TYPE I CLASS G
Vented helmet. ABS shell, textile comfort harness 6 points , wheel ratchet adjustment, adjustable size 56-63 cm. Sweat band and chin strap included. Sold with retractable clear visor PW56 included . Spare parts available.
ABS, Polycarbonate
Blue, Orange, Red, White, Yellow Adjustable 56-63cm
Endurance Plus Helmet EN 397 +50°C/-30°C; MM; LD; 440VACEN 50365 CLASS:0ANSI/ISEA Z89.1 TYPE I CLASS E
Endurance Plus ABS shell helmet - now available without retractable visor.
ABS
White Adjustable 56-63cm
Endurance Helmet EN 397 -30°C/+50°C, LDANSI/ISEA Z89.1 TYPE I CLASS G
Endurance vented ABS shell helmet - now available without retractable visor.
ABS
White Adjustable 56-63cm
EN 50365
EN 50365
IMPROVED
IMPROVED
Secure Comfortable Fit for the Wearer
470
AW15_PPE-FINAL.indd 470 05/06/2015 10:11
20
50
LD MM
PW97
20
50
PS52
PW51
PS53
CECATIII
EN 50365
Climbing Helmet EN 397 -30°C/+50°C MM LD 440VANSI/ISEA Z89.1 TYPE I
Vented helmet, adapted for working at heights. High wearing comfort polyethylene shell, six points harness, buckle adjustment. Supplied with sweat band and 4 points chin strap (Y style).
Blue, White, Yellow Adjustable 52-62cm
PE
Endurance Plus Safety Helmet EN 397 -10°C/+50°C
ABS shell helmet with extended peak to minimise glare. A 4 points nylon webbing harness, Buckle adjustable size 55-62cm. Foam sweat band included.
ABS
Blue, White, Yellow Adjustable 55-62cm
PW Full Brim Future EN 397 -10°C/+50°CANSI/ISEA Z89.1 TYPE I CLASS E
Full brim helmet with lightweight PP shell. Its wide profile provides extra protection against sun, glare, rain, debris and non-toxic splashes. A 4 points nylon harness with ratchet wheel adjustable size (52-63 cm). Soft foam sweat band included.
PP
White Adjustable 52-63cm
PW Height Endurance EN 50365 CLASS:0ANSI/ISEA Z89.1 TYPE I CLASS E - LT (OPTIONAL)EN 397 -30°C/+50°C
Designed to be specially used for working at heights. Light, comfortable and compact with a short peak. ABS shell, textile comfort harness 6 points, wheel ratchet adjustment, size 56-63 cm. Sweat band and 4 points chin strap (Y style) with soft rubber chin protector included.
ABS
Orange, Yellow, White Adjustabe 56-63cm
IMPROVED
Better Visibility, Less Cumbersome
AW15_PPE-FINAL.indd 471 04/06/2015 14:56
50 LD
PW57
50 LD
PW50
50
PA58
50
PS50
NEWCOLOUR
NEWCOLOUR
CECATIII
CECATIII
Hi-Vis PP Helmet EN 397 -10°C/+50°C, LD, 440VEN 50365 CLASS:0ANSI/ISEA Z89.1 TYPE I CLASS E
High density polypropylene Hi-Visibility shell helmet. Four-points plastic harness includes a foam backed polyester sweatband.Buckle adjustable size 55-62 cm.
PP
High-Visibility Orange, High-Visibility Yellow Adjustable 55-62cm
Endurance Safety Helmet EN 397 -10°C/+50°C, LD, 440VEN 50365 CLASS:0ANSI/ISEA Z89.1 TYPE I CLASS E
High-density polypropylene shell helmet, 4 points plastic suspension harness. Buckle adjustable size 55-62cm. Soft sweat band included.
PP
Blue, Green, Orange, Red, White, Yellow Adjustable 55-62cm
Helmet Winter Liner
This insulating liner is suitable to be worn with all helmets. Four Hook & Loop straps attach the liner to helmets for a secure fit. Can be worn with chin strap.
100% Cotton
Black,Navy one size fits all
PW Arrow Safety Helmet EN 397 -10°C/+50°CANSI/ISEA Z89.1 TYPE I CLASS C
Vented helmet with unique arrow vented design allowing a refreshing airflow around the head. High-density polypropylene shell, 4 points suspension harness with buckle adjustable size 55-62cm. Foam sweat band included.
Blue, White, Yellow Adjustable 55-62 cm
PP
IMPROVED
IMPROVED
Sub Zero Protection
Lightweight Head Protection
EN 50365
EN 50365
472
AW15_PPE-FINAL.indd 472 04/06/2015 14:56
60
PW59
60
60
PW69 PW89
60
PW79
NEWCOLOUR
NEWCOLOUR
Portwest Bump Cap
Classic design bump-cap; ventilation ports for maximum breathability. Metallic ring holes for baseball cap look.
100% Cotton, ABS, EVA Black, Navy, Royal
Adjustable 54-59 cm
EN 812
Vent Cool Bump Cap
Sport look bump cap, with large mesh panel on the top, allowing maximum airflow. Reflective stripes for enhanced safety and style.
Cotton, Mesh, ABS, EVA Black, Grey, Navy, Red
EN 812 PW Short Peak Bump Cap EN 812
Without reducing the level of performance and protection, the short peak of this bump cap gives the benefit of lighter wear and better visibility. Peak length 3cm only.
100% Cotton, ABS, EVA Foam
Black, Navy, Royal Adjustable 54-59 cm
Hi Vis Bump Cap
Modern style bump cap in Hi-Visibility colours. Mesh panel on the back which, together with covering the ventilation holes on the internal shell, help cooling comfort.
Cotton, Mesh, ABS, EVA Orange, Yellow
Adjustable 54-59 cm
EN 812
Bump CapsBump Caps can reduce the risk of head injuries in the workplace by providing head protection against minor bumps and scrapes.Combining the comfort and style of a Sport Cap with the added protection of a plastic protective shell and soft pads, PW Bump Caps provide a light weight, comfortable solution to head protection. Fashionable design also means it is a form of safety wear that employees will actually want to wear.
EN 812: 2012Industrial Bump CapsEuropean standard for bump caps for industry, describing mandatory impact and penetration tests.
NOTE: Bump Caps protect against impacts from knocks against structures and objects. They don’t protect against falling objects and in all cases where a Safety Helmet is required.
OUTER SOFT PAD for comfort and shock absorption
HIGH QUALITY PLASTIC SHELL provides good protection
Large VENTILATION HOLES for breathability
OUTER CAP made from heavy duty cotton twill
INNER SOFT PAD for extra comfort and shock absorption
HOOK & LOOP STRAP allows easy adjustment and secure fitting
473
AW15_PPE-FINAL.indd 473 04/06/2015 14:56