Owner-'s Manual - AVR 137 (English)

ENG

LISH

AVR 137 Audio/VideoReceiverOWNER’S MANUAL

2 TABLE OF CONTENTS

3 Introduction4 Safety Information4 Unpacking5 Front Panel Controls7 Rear Panel Connections9 Remote Control Functions

12 Installation and Connections12 Audio Equipment Connections13 Video Equipment Connections14 SCART A/V Connections14 AC Power Connections15 Speaker Selection and Placement16 System Configuration16 First Turn On16 Settings to be Made

With Each Input Used16 Input Setup16 Speaker Setup17 Triple Crossover Setting18 Surround Setup18 Configuring the Surround Off

(Stereo) Modes18 Stereo-Direct (Bypass) Mode19 Stereo Digital Mode19 Delay Settings19 Night Mode Settings19 Output Level Adjustment21 Operation21 Basic Operation21 Source Selection21 Controls and Use of Headphones21 Surround Mode Selection22 Surround Mode Chart24 Digital Audio Playback25 Selecting a Digital Source25 Digital Status Indicators25 Surround Mode Types26 Night Mode26 Tape Recording26 Output Level Trim Adjustment27 6-Channel Direct Input27 Display Brigthness27 Memory Backup27 Tuner Operation28 RDS Operation29 Programming the Remote29 Programming the Remote with Codes29 Code Readout30 Programmed Device Functions30 Macro Programming31 Volume Punch-Through31 Channel Control Punch-Through31 Transport Control Punch-Through31 Resetting the Remote Memory32 Function List34 Troubleshooting Guide34 Processor Reset35 Technical Specifications

Table of Contents

Typographical ConventionsIn order to help you use this manual with the remote control, front-panel controls and rear-panelconnections, certain conventions have been used.

EXAMPLE – (bold type) indicates a specific remote control or front-panel button, or rear-panelconnection jack

EXAMPLE – (OCR type) indicates a message that is visible on the front-panel information display

� – (number in a square) indicates a specific front-panel control

� – (number in a circle) indicates a rear-panel connection

0 – (number in an oval) indicates a button or indicator on the remote.

Declaration of Conformity

We, Harman Consumer Group, Inc.2, route de Tours72500 Château-du-Loir,FRANCE

declare in own responsibility, that the product described inthis owner’s manual is in compliance with technicalstandards:

EN 55013:2001 + A1:2003EN 55020:2002 + A1:2003EN 61000-3-2:2000EN 61000-3-3:1995 + A1:2001EN 60065:2002

Jurjen AmsterdamHarman Consumer Group, Inc.

04/07

ENG

LISH

INTRODUCTION 3

Introduction

Thank you for choosing Harman Kardon!With the purchase of a Harman Kardon AVR 137 you are about to begin many years oflistening enjoyment. The AVR 137 has beencustom designed to provide all the excitementand detail of movie sound tracks and everynuance of musical selections. With onboardDolby* Digital and DTS† decoding, the AVR 137delivers six discrete channels of audio that takeadvantage of the digital sound tracks from thelatest DVD and LD releases and Digital Televisionbroadcasts.

While complex digital systems are hard at workwithin the AVR 137 to make all of this happen,hookup and operation are simple. Color-keyedconnections and a programmable remotecontrol make the AVR easy to use. To obtain themaximum enjoyment from your new receiver,we urge you to take the time to read throughthis manual. This will ensure that connections tospeakers, source playback units and otherexternal devices are made properly. In addition,a few minutes spent learning the functions ofthe various controls will enable you to takeadvantage of all the power the AVR 137 is ableto deliver.

If you have any questions about this product,its installation or its operation, please contactyour dealer. He is your best local source of information.

Description and FeaturesThe AVR 137 is among the most versatile andmulti-featured A/V receivers available,incorporating a wide range of listening options.In addition to Dolby Digital and DTS decodingfor digital sources, a broad choice of analogsurround modes are available for use withsources such as CD, VCR, TV broadcasts and theAVR’s own FM/AM tuner. Along with the latestDolby ProLogic II® decoding technology, Dolby 3Stereo, 5 Ch Stereo and custom Hall and Theatermodes, only Harman Kardon receivers offer Logic 7® to create a wider, more enveloping fieldenvironment and more defined fly-overs andpans.In addition to providing a wide range of listeningoptions, the AVR 137 is easy to configure so thatit provides the best results with your speakersand specific listening-room environment.A Stereo-Direct mode bypasses the digitalprocessor to preserve all of the subtleties ofolder analog, two-channel materials, while bassmanagement, available in the surround andStereo-Digital modes,improves your ability totailor the sound to suit your room acoustics ortaste.

For the ultimate in flexibility, the AVR 137features connections for four video devices, allwith both composite and S-Video inputs,including the front-panel inputs. Two additionalaudio inputs are available, and a total of sixdigital inputs make the AVR 137 capable ofhandling all the latest digital audio sources.A video recording output and a six-channelinput make the AVR 137 virtually future-proof,with everything needed to accommodatetomorrow’s new formats right on board.

The AVR 137’s powerful amplifier usestraditional Harman Kardon high-current designtechnologies to meet the wide dynamic range ofany program selection.

Harman Kardon invented the high-fidelityreceiver fifty years ago. With state-of-the-art cir-cuitry and time-honored circuit designs, the AVR 137 is one of the finest receivers everoffered by Harman Kardon within its price range.

■ Onboard Dolby Digital and DTSDecoding Using Crystal® ChipTechnology

■ Harman Kardon’s exclusive Logic 7®

processing, along with a choice ofDolby Virtual Speaker processing foruse when only two speakers areavailable

■ Dolby Headphone to create spacious,open sound fields when using head-phones

■ Dolby Laboratory's latest ProLogic IIdecoding technology.

■ Stereo-Direct Mode for Two-ChannelSources Bypasses DSP Processing toPreserve the Integrity of AnalogMaterials

■ Stereo-Digital Mode for ProgrammableBass Management of Low FrequenciesBetween Main Speakers andSubwoofer

■ Front panel digital inputs for easy connection to portable digital devicesand the latest video game consoles

■ Multiple Digital Inputs

■ 6-Channel Direct Input for Use WithDVD-Audio or SACD Players and OtherProducts With Internal SurroundDecoders

■ Color-Coded Input,Output and SpeakerTerminals Comply With CEA Standardsfor Easy Installation

■ Remote with Internal Codes Capability

■ High-bandwidth, HDTV-compatiblecomponent video switching

■ Input titling for all input sources(except tuner)

4 SAFETY INFORMATION

Safety Information

Important Safety Information

READ THIS BEFORE OPERATINGYOUR UNIT.Do not install this equipment in a confined spacesuch as a case or similar – away from direct sunlight, heat sources, vibration, dust, moisture,and/or cold.Avoid installing this unit where foreign objectmay fall onto this unit and/or this unit may beexposed to liquid dripping or splashing. On thetop of this unit, do not place:

– Burning objects (i.e. candles), as they maycause fire, damage to this unit, and/orpersonal injury.

– Containers with liquid in them, as they mayfall and liquid may cause electrical shock tothe user and/or damage to this unit.

Do not cover this unit with a newspaper, table-cloth, curtain, etc. in order not to obstruct heatradiation. If the temperature inside this unitrises, it may cause fire, damage to this unit,and/or personal injury.

Install this unit near the AC outlet and where theAC power plug can be reached easily.

This unit is not disconnected from the AC powersource as long as it is connected to the wall out-let, even if this unit itself is turned off. This stateis called the standby mode. In this state, this unitis designed to consume a very small quantity ofpower.

WARNINGTO REDUCE THE RISK OF FIRE OR ELECTRICSHOCK, DO NOT EXPOSE THIS APPLIANCETO RAIN OR MOISTURE.

Verify Line Voltage Before UseYour AVR 137 has been designed for use with220-240-Volt AC current. Connection to a linevoltage other than that for which it is intendedcan create a safety and fire hazard and maydamage the unit.

If you have any questions about the voltagerequirements for your specific model, or aboutthe line voltage in your area, contact your dealerbefore plugging the unit into a wall outlet.

Do Not Use Extension CordsTo avoid safety hazards, use only the power cordattached to your unit. We do not recommendthat extension cords be used with this product.As with all electrical devices, do not run powercords under rugs or carpets or place heavyobjects on them. Damaged power cords shouldbe replaced immediately by an authorizedservice depot with a cord meeting factoryspecifications.

Handle the AC Power Cord GentlyWhen disconnecting the power cord from an ACoutlet, always pull the plug, never pull the cord.If you do not intend to use the unit for anyconsiderable length of time, disconnect the plugfrom the AC outlet.

Do Not Open the CabinetThere are no user-serviceable components insidethis product. Opening the cabinet may present ashock hazard, and any modification to theproduct will void your guarantee. If water or anymetal object such as a paper clip, wire or astaple accidentally falls inside the unit, discon-nect it from the AC power source immediately,and consult an authorized service station.

Installation Location■ To assure proper operation and to avoid the

potential for safety hazards, place the unit ona firm and level surface. When placing theunit on a shelf, be certain that the shelf andany mounting hardware can support theweight of the product.

■ Make certain that proper space is providedboth above and below the unit for ventilation.If this product will be installed in a cabinet orother enclosed area, make certain that thereis sufficient air movement within the cabinet.Under some circumstances a fan may berequired.

■ Do not place the unit directly on a carpetedsurface.

■ Avoid installation in extremely hot or coldlocations, or an area that is exposed to directsunlight or heating equipment.

■ Avoid moist or humid locations.

■ Do not obstruct the ventilation slots on thetop of the unit, or place objects directly overthem.

CleaningWhen the unit gets dirty, wipe it with a clean,soft, dry cloth. If necessary, wipe it with a softcloth dampened with mild soapy water, then afresh cloth with clean water. Wipe dryimmediately with a dry cloth. NEVER usebenzene, aerosol cleaners, thinner, alcohol or anyother volatile cleaning agent. Do not useabrasive cleaners, as they may damage the finishof metal parts. Avoid spraying insecticide nearthe unit.

Moving the UnitBefore moving the unit, be certain to disconnectany interconnection cords with other compo-nents, and make certain that you disconnect theunit from the AC outlet.

Unpacking

The carton and shipping materials used to pro-tect your new receiver during shipment werespecially designed to cushion it from shock andvibration. We suggest that you save the cartonand packing materials for use in shipping if youmove, or should the unit ever need repair.

To minimize the size of the carton in storage,you may wish to flatten it. This is done bycarefully slitting the tape seams on the bottomand collapsing the carton. Other cardboardinserts may be stored in the same manner.Packing materials that cannot be collapsedshould be saved along with the carton in aplastic bag.

If you do not wish to save the packagingmaterials, please note that the carton and othersections of the shipping protection arerecyclable. Please respect the environment anddiscard those materials at a local recyclingcenter.

ENG

LISH

FRONT PANEL CONTROLS 5

� Main Power Switch: Press this button toapply power to the AVR. When the switch ispressed in, the unit is placed in a Standbymode, as indicated by the orange LED 2. Thisbutton MUST be pressed in to operate the unit.To turn the unit off completely and prevent theuse of the remote control, this switch should bepressed until it pops out from the front panelso that the word “OFF” may be read at the topof the switch.

NOTE: This switch is normally left in the “ON”position.

1 System Power Control: When the MainPower Switch � is “ON,” press this button toturn on the AVR; press it again to turn the unitoff (to Standby). Note that the PowerIndicator 2 will turn blue when the unit is on.

2 Power Indicator: This LED will beilluminated in orange when the unit is in theStandby mode to signal that the unit is ready tobe turned on. When the unit is in operation, theindicator will turn blue.

3 Headphone Jack: This jack may be used tolisten to the AVR’s output through a pair ofheadphones. Be certain that the headphoneshave a standard 6.3 mm stereo phone plug.Note that the speakers will automatically beturned off when the headphones are connected.

4 Digital Optical 3 Input: Connect theoptical digital audio output of an audio or videoproduct to this jack. When the Input is not in use,be certain to keep the plastic cap installed toavoid dust contamination that might degradefuture performance.

5 Speaker/Channel Input Indicators:These indicators are multipurpose, indicatingeither the speaker type selected for each channelor the incoming data-signal configuration. Theleft, center, right, right surround and leftsurround speaker indicators are composed ofthree boxes, while the subwoofer is a single box.The center box lights when a “Small” speaker isselected, and the two outer boxes light when“Large” speakers are selected. When none ofthe boxes are lit for the center, surround orsubwoofer channels, no speaker has beenselected for that position. (See page 16 for moreinformation on configuring speakers.) The lettersinside each of the center boxes display activeinput channels. For standard analog inputs, onlythe L and R will light, indicating a stereo input.When a digital source is playing, the indicatorswill light to display the channels begin receivedat the digital input. When the letters flash, thedigital input has been interrupted. (See page 20for more information on the Channel Indicators).

Front Panel Controls

�123 4 56

7 8 9A B C D

E F G H I J

Main Power SwitchSystem Power ControlPower IndicatorHeadphone JackDigital Optical 3 InputSpeaker/Channel Input IndicatorSurround Mode Group Selector

TuningTuner Band SelectorPreset Stations SelectorInput Source SelectorRDS Select ButtonSurround Mode SelectorSurround Mode Indicators

Remote Sensor WindowMain Information DisplayDigital Coax 3 InputVideo 3 input jacksVolume ControlInput Indicators

16 7 G

9

D F IJ

16

C

7 8

9

B

H

2

4A

5

E

3

DIGITAL LOGIC 7 VID 1 DVD

CD

FMAM

TAPE

VID 2

VID 3

PRO LOGIC

3 STEREO DSP

5 CH. STEREO

SURR. OFF 6 CH

6 FRONT PANEL CONTROLS

Front Panel Controls

6 Surround Mode Group Selector: Pressthis button to select the top-level group ofsurround modes. Each press of the button willselect a major mode grouping in the followingorder:

Dolby Modes ➜ DTS Digital Modes ➜ DSPModes ➜ Stereo Modes ➜ Logic 7 Modes

Once the button is pressed so that the name ofthe desired surround mode group appears in theLower Display Line F, press the SurroundMode Selector C to cycle through the indi-vidual modes available. For example, press thisbutton to select Dolby modes, and then pressthe Surround Mode Selector C to choosefrom the various mode options.

7 Tuning Selector: Press the left side of thebutton to tune lower frequency stations and theright side of the button to tune higher frequencystations. When a station with a strong signal isreached, MANUAL TUNED or AUTOTUNED will appear in the Main InformationDisplay F (see page 27 for more informationon tuning stations).

8 Tuner Band Selector: Pressing this buttonwill automatically switch the AVR to the Tunermode. Pressing it again will switch between theAM and FM frequency bands, holding it pressedfor some seconds will switch between stereoand mono receiving and between automatic andmanual tuning mode (See page 27 for moreinformation on the tuner).

9 Preset Stations Selector: Press thisbutton to scroll up or down through the list ofstations that have been entered into the presetmemory. (See page 27 for more information ontuner programming.)

A Input Source Selector: Press this buttonto change the input by scrolling through the listof input sources.

B RDS Select Button: Press this button todisplay the various messages that are part of theRDS data system of the AVR’s tuner. (See page 28for more information on RDS).

C Surround Mode Selector: Press this but-ton to select from among the available surroundmode options for the mode group selected. Thespecific modes will vary based on the number ofspeakers available, the mode group and if theinput source is digital or analog. For example,press the Surround Mode Group Selector6 to select a mode grouping such as Dolby orLogic 7, and then press this button to see themode choices available. For more information onmode selection, see page 21.

D Surround Mode Indicators: Indicator willilluminate in front of the surround mode that iscurrently in use.

E Remote Sensor Window: The sensorbehind this window receives infrared signalsfrom the remote control. Aim the remote at thisarea and do not block or cover it unless anexternal remote sensor is installed.

F Main Information Display: This displaydelivers messages and status indications to helpyou operate the receiver.

G Digital Coax 3 Input: This jack is normallyused for connection to the output of portabledigital audio devices, video game consoles orother products that have a coax digital jack.

H Video 3 Input Jacks: These audio/videojacks may be used for temporary connection tovideo games or portable audio/video productssuch as camcorders and portable audio players.

I Volume Control: Turn this knob clockwiseto increase the volume, counterclockwise todecrease the volume. If the AVR is muted,adjusting volume control will automaticallyrelease the unit from the silenced condition.

J Input indicators: Indicator will illuminatein front of the input that is currently being usedas the source for the AVR.

ENG

LISH

REAR PANEL CONNECTIONS 7

Rear Panel Connections

VID 2 IN DVD IN COMPONENT VIDEO INMONITOR OUTOUT VID 1 IN

••

¢

°¶

c⁄

�

fi

°�

‚

d

e

¢

¶

¡

™

b ·

‡fl

›‹

ª

‹

a

M

§£

ID

∞

��

��

��

Tape InputsTape OutputsVideo 1 Audio InputsAM AntennaVideo 1 Audio OutputsDVD Audio InputsFM AntennaCD InputsVideo 2 Component Video Inputs

Coaxial Digital InputsSubwoofer OutputVideo Monitor OutputsFront/Center Speaker OutputsSurround Speaker OutputsComponent Video OutputsVideo 1 Component Video InputsAC Power CordDVD Video Inputs

Video 1 Video OutputsVideo 2 Audio InputsVideo 2 Video InputsOptical Digital InputsVideo 1 Video Inputs6-Channel Direct Inputs

� Tape Inputs: Connect these jacks to thePLAY/OUT jacks of an audio recorder.

� Tape Outputs: Connect these jacks to theRECORD/INPUT jacks of an audio recorder.

� Video 1 Audio Inputs: Connect these jacksto the PLAY/OUT audio jacks on a TV or othervideo source.

� AM Antenna: Connect the AM loop antennasupplied with the receiver to these terminals. If anexternal AM antenna is used, make connections tothe AM and GND terminals in accordance withthe instructions supplied with the antenna.

� Video 1 Audio Outputs: Connect thesejacks to the RECORD/INPUT audio jacks on a VCR or any other Audio recorder.

� DVD Audio Inputs: Connect these jacks tothe analog audio jacks on a DVD or other videosource.

� FM Antenna: Connect the supplied indoor oran optional external FM antenna to this terminal.

CD Inputs: Connect these jacks to theanalog output of a compact disc player or CDchanger.

Video 2 Component Video Inputs:Connect the Y/Pr/Pb component video outputs ofan HDTV Set-top convertor, satellite receiver, orother video source device with component videooutputs to these jacks.

� Coaxial Digital Inputs: Connect the coaxdigital output from a DVD player, HDTV receiver,LD player, MD player or CD player to these jacks.The signal may be either a Dolby Digital signal,DTS signal or a standard PCM digital source.Do not connect the RF digital output of an LDplayer to these jacks.

� Subwoofer Output: Connect this jack tothe line-level input of a powered subwoofer. Ifan external subwoofer amplifier is used, connectthis jack to the subwoofer amplifier input.

8 REAR PANEL CONNECTIONS

Rear Panel Connections

Video Monitor Outputs: Connect thesejacks to the composite and/or S-Video input of aTV monitor or video projector to view the outputof any video source selected by the receiver’svideo switcher.

� Front/Center Speaker Outputs: Connectthese outputs to the matching + or – terminalson your front/center speakers. When makingspeaker connections, always make certain tomaintain correct polarity by connecting the red(+) terminals on the AVR to the red (+) terminalson the speaker and the black (–) terminals onthe AVR to the black (–) terminals on thespeakers. (See page 12 for more information onspeaker polarity.)

� Surround Speaker Outputs: Connectthese outputs to the matching + or – terminalson your left and right surround speakers. Whenmaking speaker connections always make cer-tain to maintain correct polarity by connectingthe red (+) terminals on the AVR to the red (+)terminals on the speakers and the black (–)terminals on the AVR to the black (–) terminalson the speakers. See page 12 for moreinformation on speaker polarity.

� Monitor Component Video Outputs:Connect these outputs to the component videoinputs of a video projector or monitor. When asource connected to one of the twoComponent Video Inputs � is selectedthe signal will be sent to these jacks.

� Video 1 Component Video Inputs:Connect the Y/Pr/Pb component video outputs ofa DVD player to these jacks.

Note: All component inputs/outputs can beused for RGB signals too, in the same way asdescribed for the Y/Pr/Pb signals, then connectedto the jacks with the corresponding color.RGB connection is not possible if the sourceoutputs a separate sync signal (see page 13).

� AC Power Cord: Connect the AC plug to anunswitched AC wall output.

� DVD Video Inputs: Connect these jacks tothe composite or S-Video output jacks on a DVDplayer or other video source.

� Video 1 Video Outputs: Connect thesejacks to the RECORD/INPUT composite or S-Video jack on a VCR.

� Video 2 Audio Inputs: Connect these jacksto the PLAY/OUT audio jacks on a VCR or othervideo source.

� Video 2 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks ona second VCR or other video source.

� Optical Digital Inputs: Connect the opticaldigital output from a DVD player, HDTV receiver,LD player, MD player or CD player to these jacks.The signal may be either a Dolby Digital signal, aDTS signal or a standard PCM digital source.

� Video 1 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks ona TV or other video source.

Note: Either the Video or S-Video output of anyS-Video source must be connected to the AVR, not both in parallel, otherwise the videomay be disturbed or its performance beadversely effected.

� 6-Channel Direct Inputs: These jacks areused for connection to source devices such asDVD-Audio or SACD players with discrete analogoutputs.

ENG

LISH

REMOTE CONTROL FUNCTIONS 9

Remote Control Functions

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

�

�

�

�

�

�

�

�

�

�

�

Power On ButtonIR Transmitter WindowProgram IndicatorPower Off ButtonInput SelectorsAVR SelectorAM/FM Tuner SelectTest ButtonSleep ButtonSurround Mode SelectorNight ModeChannel Select ButtonK/L ButtonsA ButtonSet ButtonDigital SelectNumeric KeysTuner ModeDirect ButtonTuning Up/DownMacro ButtonsTransport ControlsSkip Up/Down ButtonsRDS Select ButtonPreset Up/DownClear ButtonMemory ButtonDelay/Prev. Ch.B ButtonSpeaker SelectTone Mode ButtonVolume Up/DownTV/Video SelectorMuteDim ButtonDolby Mode Select ButtonDTS Digital Mode Select ButtonLogic 7 Mode Select ButtonStereo Mode Select ButtonDTS Neo:6 Mode Select Button6-Channel Direct Input

NOTE: The function names shown here are eachbutton’s feature when used with the AVR. Mostbuttons have additional functions when usedwith other devices. See page 32 and 33 for a listof these functions.

ae

7

l

q

r

t

`

l

q

t

`z

x

y

p

8

�

�

�

�

�

�

�

�

�

g

j

k

mn

o

s

u

��

w

v

b dc

f

10 REMOTE CONTROL FUNCTIONS


IMPORTANT NOTE: The AVR’s remote may beprogrammed to control up to seven devices,including the AVR. Before using the remote, it isimportant to remember to press the InputSelector button 4 that corresponds to theunit you wish to operate. In addition, the AVR’sremote is shipped from the factory to operate theAVR and most Harman Kardon CD or DVDplayers and cassette decks. The remote is alsocapable of operating a wide variety of otherproducts using the control codes that are part ofthe remote. Before using the remote with otherproducts, follow the instructions on page 29 toprogram the proper codes for the products inyour system.

It is also important to remember that many of thebuttons on the remote take on differentfunctions, depending on the product selectedusing the Input Selectors. The descriptions shownhere primarily detail the functions of the remotewhen it is used to operate the AVR. (See page 32and 33 for information about alternate functionsfor the remote’s buttons.)

0 Power On Button: Press this button toturn on the power to a device selected by pressingone of the Input Selectors 4 (except Tape).

1 IR Transmitter Window: Point this windowtowards the AVR when pressing buttons on theremote to make certain that infrared commandsare properly received.

2 Program Indicator: This three-colorindicator is used to guide you through theprocess of programming the remote. See page 29for information on programming the remote.

3 Power Off Button: Press this button toplace the AVR or a selected device unit in theStandby mode.

4 Input Selectors: Pressing one of thesebuttons will perform three actions at the sametime. First, if the AVR is not turned on, this willpower up the unit. Next, it will select the sourceshown on the button as the input to the AVR.Finally, it will change the remote control so thatit controls the device selected. After pressing oneof these buttons you must press the AVR Selector button 5 again to operate theAVR’s functions with the remote.

5 AVR Selector: Pressing this button willswitch the remote so that it will operate the AVR’sfunctions. If the AVR is in the Standby mode, it willalso turn the AVR on.

6 AM/FM Tuner Select: Press this button toselect the AVR’s tuner as the listening choice.Pressing this button when the tuner is in use willselect between the AM and FM bands.

7 Test Tone: Press this button to begin thesequence used to calibrate the AVR’s outputlevels. (See page 19 for more information on calibrating the AVR.)

8 Sleep Button: Press this button to placethe unit in the Sleep mode. After the time shownin the display, the AVR will automatically go intothe Standby mode. Each press of the buttonchanges the time until turn-off in the following order:

Hold the button pressed for two seconds to turnoff the Sleep mode setting.Note that this button is also used to changechannels on your TV, VCR and SAT receiver whenselected.

9 Surround Mode Selector: Press thisbutton to begin the process of changingthe surround mode. After the button hasbeen pressed, use the K/L buttons C toselect the desired surround mode (See page 21for more information). Note that this button isalso used to tune channels when the TV, VCRand SAT receiver is selected using the InputSelector 4.

A Night Mode: Press this button to activatethe Night mode. This mode is available only withDolby Digital encoded digital sources, and itpreserves dialog (center channel) intelligibilty atlow volume levels (See page 26 for moreinformation).

B Channel Select Button: This button isused to start the process of setting the AVR’s out-put levels with an external source. Once this buttonis pressed, use the K/L buttons C to select thechannel being adjusted, then press the Set buttonE, followed by the K/L buttons again, tochange the level setting. (See page 27 for moreinformation.)

C K/L Buttons: These are multi-purposebuttons.They will be used most frequently to selecta surround mode.These buttons are also used toincrease or decrease output levels whenconfiguring the unit, to select speakerconfiguration or to select the digital inputs. Theyare also used to enter delay time settings afterthe Delay button � has been pressed.

When the AVR remote is being programmed forthe codes of another device, these buttons arealso used in the “Auto Search” process (See page29 for more information on programming theremote.)

D A Button: This button does not have afunction with the AVR. When a DVD player or TVis selected, it may be used to navigate the menusof those devices.

E Set Button: This button is used to entersettings into the AVR’s memory. It is also used inthe setup procedures for delay time, speakerconfiguration and channel output leveladjustment.

F Digital Select: Press this button to assignone of the digital inputs 4G�� to asource. (See page 25 for more information onusing digital inputs.)

G Numeric Keys: These buttons serve as aten-button numeric keypad to enter tuner presetpositions. They are also used to select channelnumbers when TV, VCR or Sat receiver hasbeen selected on the remote, or to select tracknumbers on a CD, DVD or LD player, dependingon how the remote has been programmed.

H Tuner Mode: Press this button when thetuner is in use to select between automatictuning and manual tuning. When the button ispressed so MANUAL appears in the MainInformation Display F, pressing the Tuningbuttons J7 will move the frequency up ordown in single-step increments. When the FMband is in use and AUTO appears in the MainInformation Display F, pressing this buttonwill change to monaural reception making evenweek stations audible. (See page 27 for moreinformation.)

I Direct Button: Press this button when thetuner is in use to start the sequence for directentry of a station’s frequency. After pressing thebutton simply press the proper Numeric KeysG to select a station (See page 27 for moreinformation on the tuner).

J Tuning Up/Down: When the tuner is in use,these buttons will tune up or down through theselected frequency band. If the Tuner Modebutton H has been pressed or the Band button8 on the front panel was held pressed so thatAUTO appears in the Main InformationDisplay F, pressing either of the buttons willcause the tuner to seek the next station withacceptable signal strength for quality reception.When the MANUAL appears in the MainInformation Display F, pressing thesebuttons will tune stations in single-stepincrements. (See page 27 for more information.)

90min

80min

70min

60min

50min

40min

30min

20min

10min OFF

ENG

LISH

REMOTE CONTROL FUNCTIONS 11


K Macro Buttons: Press these buttons tostore or recall a “Macro”, which is a pre-programmed sequence of commands stored in the remote. (See page 30 for moreinformation on storing and recalling macros.)

L Transport Buttons: These buttons do nothave any functions for the AVR, but they may beprogrammed for the forward/reverse playoperation of a wide variety of CD or DVDplayers, and audio or video- cassette recorders.(See page 29 for more information onprogramming the remote.)

M Skip Up/Down Buttons: These buttonsdo not have a direct function with the AVR, butwhen used with a compatibly programmed CDor DVD changer they will change the tracks onthe disc currently being played in the changer.

N RDS Select Button: Press this button todisplay the various messages that are part of theRDS data system of the AVR’s tuner. (See page 28for more information on RDS).

O Preset Up/Down: When the tuner is inuse, press these buttons to scroll through thestations programmed into the AVR’s memory.When CD or DVD is selected using the InputSelector button 4, these buttons may func-tion as Slow Fwd/Rev (DVD) or ”+10” (CD).

P Clear Button: Press this button to clearincorrect entries when using the remote to directly enter a radio station’s frequency.

Q Memory Button: Press this button to entera radio station into the AVR’s preset memory. Twounderline indicators will flash at the right side ofthe Main Information Display F, you thenhave five seconds to enter a preset memorylocation using the Numeric Keys G. (Seepage 27 for more information.)

� Delay/Prev Ch.: Press this button to beginthe process for setting the delay times used bythe AVR when processing surround sound. Afterpressing this button, the delay times are enteredby pressing the Set button E and then usingthe K/L buttons C to change the setting.Press the Set button again to complete theprocess. (See page 19 for more information.)

� B Button: This button does not have afunction with the AVR. When a DVD player or TVis selected, it may be used to navigate the menusof those devices.

� Speaker Select: Press this button tobegin the process of configuring the AVR’s BassManagement System for use with the type ofspeakers used in your system. Once the buttonhas been pressed, use the K/L buttons C toselect the channel you wish to set up. Press theSet button E and then select the speakertype (see page 16 for more information.)

� Tone Mode: Pressing this button enablesor disables the Balance, Bass and Treble tonecontrols. When the button is pressed so that thewords TONE IN appear in the MainInformation Display F, the settings of theBass and Treble controls and of the Balancecontrol will affect the output signals. When thebutton is pressed so that the words TONEOUT appear in the Main InformationDisplay F, the output signal will be “flat,”without any balance, bass or treble alteration.

�Volume Up/Down: Press these buttons toraise or lower the system volume.

� TV/Video Button: This button does nothave a direct function on the AVR, but whenused with a compatibly programmed VCR, DVDor satellite receiver that has a “TV/Video”function, pressing this button will switchbetween the output of the player or receiver andthe external video input to that player. Consultthe Owner’s Manual for your specific player orreceiver for the details of how it implements thisfunction.

� Mute: Press this button to momentarilysilence the AVR or TV set being controlled,depending on which device has been selected.

When the AVR remote is being programmed tooperate another device, this button is pressedwith the Input Selector button 4 to beginthe programming process. (See page 29 for moreinformation on programming the remote.)

NOTE: As any of the remote buttons pressed isactive with the device selected, thecorresponding Selector button 45 willbriefly flash red to confirm your selection.

Dim Button: Press this button to activatethe Dimmer function, which reduces the bright-ness of the front panel display, or turn it offentirely. The first press of the button shows thedefault state, which is full brightness byindicating VFD FULL in the MainInformation Display F. Press the buttonagain within five seconds to reduce thebrightness by 50%, as indicated by VFDHALF. Press the button again within fiveseconds and the main display will go completelydark. Note that this setting is temporary; thedisplay will always return to full brightness whenthe AVR is turned on. In addition,both thePower Indicator 2 and the blue accentlighting inside the volume control will alwaysremain at full brightness regardless of thesetting. This is to remind you that the AVR is stillturned on.

Dolby Mode Selector: This button is usedto select one of the available Dolby Surround processing modes. Each press of this button willselect one of the Dolby Pro Logic II modes,Dolby 3 Stereo or Dolby Digital. Note that the

Dolby Digital mode is only available with adigital input selected and the other modes onlyas long as a Dolby Digital source is not playing.See page 22 for the available Dolby surroundmode options.

� DTS Digital Mode Selector: When a DTSsource is in use the AVR will select theappropriate mode automatically and no othermode will be available. Pressing this button willdisplay the mode currently selected by the AVR´sdecoder, depending on the surround materialplayed and the speaker setting.

� Logic 7 Selector: Press this button toselect one of the available Logic 7 surroundmodes. (See page 22 for the available Logic 7options).

Stereo Mode Selector: Press this button toselect a stereo playback mode. When the buttonis pressed so that DSP SURR OFF appearsin the Main Information Display F, the AVRwill operate in a bypass mode with true fullyanalog, two-channel left/right stereo mode withno surround processing or bass management asopposed to other modes where digital process-ing is used. When the button is pressed so thatSURROUND OFF appears in the MainInformation Display F, you may enjoy atwo-channel presentation of the sound alongwith the benefits of bass management. Whenthe button is pressed so that 5 CH STEREOappears, the stereo signal is routed to all fivespeakers, if installed.(See page 18 for moreinformation on stereo playback modes).

� DTS Neo:6 Mode Selector: Pressing thisselector button cycles the AVR through the various DTS Neo:6 modes, which extract a five-channel surround field from two-channelprogram material (from PCM source or analoginput signal). The first press selects the last DTSNeo:6 surround mode that was in use, and eachsubsequent press selects the next mode in thefollowing order:

� 6-Channel Direct Input: Press this buttonto select the component connected to the 6-Channel Direct Input N as the audio.Note that when you wish to use the Six ChannelDirect Input in conjunction with a video source,you must first select the video source by pressingone of the Input Selectors 4. Then press thisbutton to choose the 6-Channel Direct InputN as the audio source.

DTS Neo:6 MUSIC

DTS Neo:6 CINEMA

12 INSTALLATION AND CONNECTIONS

After unpacking the unit, and placing it on a solidsurface capable of supporting its weight, you willneed to make the connections to your audio andvideo equipment.

Audio Equipment Connections

We recommend that you use high-qualityinterconnect cables when making connections tosource equipment and recorders to preserve theintegrity of the signals.

When making connections to audio sourceequipment or speakers it is always a goodpractice to unplug the unit from the AC walloutlet. This prevents any possibility ofaccidentally sending audio or transient signals tothe speakers that may damage them.

Important Note : In order to clearly identify allconnectors and simplify nstallation, as per thenew EIA/CEA-863 standard, all connections arecolour coded as follows:For Speakers and Audio In/Outputs: White (Left,speakers front) and Red (Right, speakers front).For Speakers: Green (Center), Blue (LeftSurround) and Grey (Right Surround).For Audio Output: Purple (Subwoofer).For Composite Video In/Outputs: Yellow.For Digital Audio In/Outputs: Orange.

1. Connect the analog output of a CD player tothe CD inputs .

NOTE: When the CD player has both fixed andvariable audio outputs it is best to use the fixedoutput unless you find that the input to thereceiver is so low that the sound is noisy, or sohigh that the signal is distorted.

2. Connect the analog Play/Out jacks of acassette deck, MD, CD-R or other audio recorderto the Tape Input jacks �. Connect the analogRecord/In jacks on the recorder to the TapeOutput jacks � on the AVR.

3. Connect the output of any digital sources tothe appropriate input connections on the AVRrear panel. Note that the Optical and Coaxialdigital inputs ��4G may be used with aDolby Digital or DTS source or the output of aconventional CD, MD or LD player’s PCM (S/P-DIF) output.

4. Assemble the AM Loop Antenna supplied withthe unit as shown below. Connect it to the AMand GND screw terminals �.

5. Connect the supplied FM antenna to the FM(75 ohm) connection �. The FM antenna maybe an external roof antenna, an inside poweredor wire lead antenna or a connection from acable system. Note that if the antenna orconnection uses 300-ohm twin-lead cable, youmust use a 300-ohm-to-75-ohm adapter tomake the connection.

6. Connect the front, center and surroundspeaker outputs �� to the respectivespeakers.

To assure that all the audio signals are carried toyour speakers without loss of clarity orresolution, we suggest that you use high-qualityspeaker cable. Many brands of cable areavailable and the choice of cable may beinfluenced by the distance between yourspeakers and the receiver, the type of speakersyou use, personal preferences and other factors.Your dealer or installer is a valuable resource toconsult in selecting the proper cable.

Regardless of the brand of cable selected, werecommend that you use a cable constructed offine, multistrand copper with an area greaterthan 2 mm2.

Cable with an area of 1.5 mm2 may be used forshort runs of less than 4 m. We do notrecommend that you use cables with an area lessthan 1mm2 due to the power loss anddegradation in performance that will occur.

Cables that are run inside walls should have theappropriate markings to indicate listing with UL,CSA or other appropriate testing agencystandards. Questions about running cablesinside walls should be referred to your installeror a licensed electrical contractor who is familiarwith the applicable local building codes in yourarea.

When connecting wires to the speakers, becertain to observe proper polarity. Remember toconnect the “negative” or “black” wire to thesame terminal on both the receiver and thespeaker. Similarly, the “positive” or “red” wireshould be connected to like terminals on theAVR and speaker.

NOTE: While most speaker manufacturersadhere to an industry convention of using blackterminals for negative and red ones for positive,some manufacturers may vary from thisconfiguration. To assure proper phase andoptimal performance, consult the identificationplate on your speaker or the speaker’s manual toverify polarity. If you do not know the polarity ofyour speaker, ask your dealer for advice beforeproceeding, or consult the speaker’smanufacturer.

We also recommend that the length of cableused to connect speaker pairs be identical. Forexample, use the same length piece of cable toconnect the front-left and front-right orsurround-left and surround-right speakers,even if the speakers are a different distancefrom the AVR.

7. Connections to a subwoofer are normallymade via a line level audio connection from theSubwoofer Output � to the line-level inputof a subwoofer with a built-in amplifier. When apassive subwoofer is used, the connection firstgoes to a power amplifier, which will be connected to one or more subwoofer speakers.If you are using a powered subwoofer that doesnot have line-level input connections, follow theinstructions furnished with the speaker for connection information.

Note: Speaker sets with two front satellites anda passive subwoofer must be connected to thefront speaker outputs � only rather than to theSubwoofer Output �.

8. If an external multi-channel audio source with5.1 outputs such as an external digitalprocessor/decoder, DVD-Audio or SACD player isused, connect the outputs of that device to the 6-Channel Direct Inputs �.

Installation and Connections

ENG

LISH

INSTALLATION AND CONNECTIONS 13


Video Equipment Connections

Video equipment is connected in the same manneras audio components. Again, the use of high-quality interconnect cables is recommended topreserve signal quality. To ensure best videoperformance S-Video sources should beconnected to the AVR only with their S-VideoIn/Outputs, not with their composite videoconnectors too.

1. Connect a VCR’s audio and video Play/Outjacks to the Video 2 In jacks �� on the rearpanel. The Audio and Video Record/In jacks onthe VCR should be connected to the Video 1Out jacks �� on the AVR.

2. Although any video device may be connectedto these jacks, we recommend connecting your TVto the Video 1 Audio/Video Input Jacks�� so that you may take advantage of the factthat the remote control is preprogrammed withTV product codes for the Video 1 device.For the same reason, we recommend connectingyour video recorder, cable TV converter or satellitereceiver to the Video 2 Audio/Video InputJacks ��.

3. Connect the analog audio and video outputsof a DVD or laser disc player to the DVD jacks�� .

4. Connect the digital audio outputs of a CD, MDor DVD player, satellite receiver, cable box orHDTV converter to the appropriate Optical orCoaxial Digital Inputs ��4G.Remember that the DVD source defaults to theCoaxial 1 Digital Input �. All other sourcesdefault to their analog inputs, although anysource may be assigned to any digital audio inputon the receiver.

5. Connect the Composite and S-Video (if S-Video device is in use) Monitor Output jacks on the receiver to the composite and S-Video input of your television monitor or videoprojector.

6. If your DVD player and monitor both havecomponent video connections, connect thecomponent outputs of the DVD player to theVideo 1 Component Video Inputs �. Notethat even when component video connections areused the audio connections must still be made toeither the analog DVD Audio Inputs � or anyof the Coaxial or Optical Digital Input jacks��.

7. If another component video device is available,connect it to the Video 2 Component VideoInput jacks . The audio connections for thisdevice should be made to either the Video 2Input jacks � or any of the Coaxial or OpticalDigital Input jacks ��.

8. If the component video inputs are used,connect the Component Video Output � tothe component video inputs of your TV, projectoror display device.

9. If you have a camcorder, video game or otheraudio/video device that is connected to the AVRon a temporary, rather than permanent basis,connect the audio, video and digital audio out-puts of that device to the Front Panel Inputs4GH. A device connected to the Video 3jacks H is selected as the Video 3 input, andconnected to the digital jacks 4G it is selected as "Optical 3" or "Coaxial 3" input.(See page 16 for more information on inputconfiguration.)

Video Connection Notes:• Y/Pr/Pb Component, RGB (see page 14), or

Composite video signals may only be viewed intheir native formats and will not be convertedto the other formats.

• All component inputs/outputs can be used forRGB signals too, in the same way as describedfor the Y/Pr/Pb signals, then connected to thejacks with the corresponding color.But this is only correct as long as only the threeRGB video signals are output by the videosource, with a sync signal in the "G" signalonly, without any sync signal output separatelyby the source.

14 INSTALLATION AND CONNECTIONS


SCART A/V Connections

For the connections described above your videodevice needs RCA (cinch) connectors or/and S-Video connectors for all Audio and Video signals:Any normal video device (Not SVHS or High 8) foronly playback needs 3 RCA jacks, VCRs for recordand playback even 6 RCA jacks. Any S-Videodevice (SVHS, High 8) needs 2 RCA (Audio) and 1 S-Video jack (Video), if it´s a playback unit, or 4 RCA (Audio In/Out) and 2 S-Video (VideoIn/Out) jacks, if it´s a recording VCR.

Many european video devices are equipped withRCA (Cinch) or S-Video jacks only partially, notwith all audio and video in/outputs needed asdescribed above, but with a so called Scart orEuro-AV connector (almost rectangular jack with21 pins, see drawings on this page).

In that case the following Scart to Cinch adaptersor cables are needed:

• Units for playback, such as satellite receivers,camcorders, DVD or LD players, need an adapterfrom Scart to 3 RCA plugs, see fig. 1 (normalvideo devices) or from Scart to 2 RCA+1 S-Video plugs, see fig. 4 (S-Video devices).

• HiFi VCRs need an adapter from Scart to 6 RCAplugs, see fig. 2 (normal video), or from Scart to4 Audio+2S-Video jacks, see fig. 5 (S-VideoVCR). Read carefully the instruction attached tothe adapter to find which of the six plugs isused for the record signal to the VCR (connectwith the AVR´s Out jacks) and for the playbacksignal from the VCR (connect with the AVR´s Injacks). Do not misconnect Audio and Videosignals. Don´t hesitate to consult your dealer, ifyou are uncertain.

• If you use only normal video devices the TVmonitor needs an adapter from 3 RCA plugs toScart (fig. 3) only. If also S-Video devices areused an adapter from 2 RCA+1S-Video plugs toScart is needed additionally (fig. 6), connectedto the SCART input on your TV that is providedfor S-Video.

Note that only the video plugs (the "yellow"cinch plug in fig. 3 and the S-Video plug in fig. 6)must be connected to the TV Monitor Output , and the volume on the TV must be reduced tominimum.

Important Note for Adapter Cables:If the cinch connectors of the adapter you’ll useare labeled, connect the Audio and Video ”In”plugs with the corresponding Audio and Video”In” jacks on the AVR (and with a VCR connectthe ”Out” plugs to the ”Out” jacks on the AVR).Note that with some adapter types it may be justturned around: If no signal is audible/ visiblewhen the VCR is playing connect the “Out” plugsto the ”In” jacks on the AVR and turned around.If the adapter plugs are not labeled in that way,pay attention to the signal flow directions as

Black

Yellow

Red

Figure 1:SCART/Cinch-Adapter for

playback;signal flow:

SCART → Cinch

Black

Red

Blue

Yellow

Green

White

Figure 2:SCART/Cinch-Adapter for

record and playback;signal flow:

SCART ↔ Cinch

Black

Yellow

Red

Figure 3:Cinch/SCART-Adapter for

playback;signal flow:

Cinch → SCART

Rot

Schwarz

S-Video In

Figure 4:SCART/S-Video Adapter

for playback;signal flow:

SCART → Cinch

Schwarz

Rot

Blau

Gelb

S-Video In

S-Video Out

Figure 5:SCART/S-Video Adapterfor record and playback;

signal flow:SCART ↔ Cinch

Rot

Schwarz

S-Video Out

Figure 6:SCART/S-Video Adapter

for playback;signal flow:

Cinch → SCART

Black

Yellow

Red

Black

Red

Blue1

Yellow

Green1

White

Black

Yellow

Red

Red

Black

S-Video In

Red

Black

S-Video Out

Black

Red

Blue1

Yellow

S-Video In

S-Video Out

1 Also other colours possible, e.g. brown and grey.

shown in the diagrams above and in the instruc-tion attached to the adapter. If uncertain, don’thesitate to consult your dealer.

Important Notes for S-Video connections:1. Only the S-Video In/Out of S-Video devicesmust be connected to the AVR, NOT both,normal video and S-Video In/Outputs (except theTV, see item 2).

2. Like most common AV units the AVR does notconvert the Video signal to S-Video or vice versa.Thus both connections must be made from theAVR to the TV if both, Video and S-Videosources, are used, and the appropriate input onthe TV must be selected.

Important Note for the Use of SCART-Cinch Adapters:When video sources are connected to the TVdirectly with a SCART cable, specific control sig-nals apart from Audio/Video signals will be fedto the TV. These specific signals are: With allvideo sources, the signal for automatic inputselection that switches the TV automatically tothe appropriate input as soon as the videosource is started. And with DVD players, the sig-nals automatically turning the TV to 4:3/16:9format (with 16:9 TVs or 4:3 TVs with 16:9capability) and turning the RGB video decoder ofthe TV on or off, depending on the DVD player´ssetting. With any adapter cable, these controlsignals will be lost and the appropriate settingof the TV must be made manually.

ENG

LISH

INSTALLATION AND CONNECTIONS 15


Speaker Selection

No matter which type or brand of speakers isused, the same model or brand of speakershould be used at least for the front-left, centerand front-right speakers. This creates a seamlessfront soundstage and eliminates the possibilityof distracting sonic disturbances that occur whena sound moves across mismatched front-channelspeakers.

Speaker Placement

The placement of speakers in a multichannelhome-theater system can have a noticeableimpact on the quality of sound reproduced.

Depending on the type of center-channelspeaker in use and your viewing device, placethe center speaker either directly above or belowyour TV, or in the center behind a perforatedfront-projection screen.

Once the center-channel speaker is installed,position the left-front and right-front speakers sothat they are as far away from one another asthe center-channel speaker is from the preferredlistening position. Ideally, the front-channelspeakers should be placed so that their tweetersare no more than 60cm above or below thetweeter in the center-channel speaker.

They should also be at least 0.5 meter from yourTV set unless the speakers are magneticallyshielded to avoid colourings on the TV screen.Note that most speakers are not shielded, evenwith complete surround sets only the Centerspeaker may be.

Depending on the specifics of your roomacoustics and the type of speakers in use, youmay find that imaging is improved by moving thefront-left and front-right speakers slightlyforward of the center-channel speaker. Ifpossible, adjust all front loudspeakers so thatthey are aimed at ear height when you areseated in the listening position.

Using these guidelines, you’ll find that it takessome experimentation to find the correctlocation for the front speakers in your particularinstallation. Don’t be afraid to move thingsaround until the system sounds correct. Optimizeyour speakers so that audio transitions acrossthe front of the room sound smooth.

Surround speakers should be placed on the sidewalls of the room, at or slightly behind thelistening position. The center of the speakershould face you.

If side-wall mounting is not practical, thespeakers may be placed on a rear wall, behindthe listening position. The speakers should be nomore than two meters behind the rear of theseating area.

Subwoofers produce largely nondirectionalsound, so they may be placed almost anywherein a room. Actual placement should be based onroom size and shape and the type of subwooferused. One method of finding the optimallocation for a subwoofer is to begin by placing itin the front of the room, about 15cm from awall, or near the front corner of the room.Another method is to temporarily place thesubwoofer in the spot where you will normallysit, and then walk around the room until youfind a spot where the subwoofer sounds best.Place the subwoofer in that spot. You shouldalso follow the instructions of the subwoofer’smanufacturer, or you may wish to experimentwith the best location for a subwoofer in yourlistening room.

Right FrontSpeaker

Left FrontSpeaker

No more than 60cm

Center Front Speaker

A) Front Channel Speaker Installation withDirect-View TV Sets or Rear-Screen Projectors

B) The distance between the left and rightspeakers should be equal to the distance fromthe seating position to the viewing screen. You may also experiment with placing the leftand right speakers slightly forward of the centerspeaker.

5.1-Channel System

16 SYSTEM CONFIGURATION

System Configuration

Once the speakers have been placed in theroom and connected, the remaining steps are toprogram the system configuration memories.With the AVR two kind of memories are used,those associated individually with the inputselected, e.g. surround modes, and othersworking independently from any input selectedlike speaker output levels, or delay times usedby the surround sound processor.

First Turn On

You are now ready to power up the AVR tobegin these final adjustments.

1. Plug the Power Cable � into an un-switched AC outlet.

2. Press the Main Power Switch � in until itlatches and the word “OFF” on the top of theswitch disappears inside the front panel. Notethat the Power Indicator 2 will turn orange,indicating that the unit is in the Standby mode.

3. Remove the protective plastic film from thefront-panel lens. If left in place, the film mayaffect the performance of your remote control.

4. Install the three supplied AAA batteries in theremote as shown. Be certain to follow the (+)and (–) polarity indicators that are on thebottom of the battery compartment.

5. Turn the AVR on either by pressing theSystem Power Control 1 or the InputSource Selector A on the front panel, or viathe remote by pressing the AVR Selector 5or any of the Input Selectors 46 on theremote. The Power Indicator 2 will turn blueto confirm that the unit is on, and the MainInformation Display F will also light up.

NOTE: After pressing one of the Input Selectorbuttons 4 to turn the unit on, press the AVRSelector 5 to have the remote control the AVRfunctions.

Settings to be Made With EachInput Used

The AVR features an advanced memory systemthat enables you to establish different settingsfor the speaker configuration, digital input, sur-round mode, delay times and output levels foreach input source. This flexibility enables you tocustom tailor the way in which you listen to eachsource and have the AVR memorize them. Thismeans, for example, that you may associatedifferent surround modes and analog or digitalinputs with different sources, or set differentspeaker configurations with the resultantchanges to the bass management system or theuse of the Center speaker. Once these settingsare made, they will automatically be recalledwhenever you select an input.

The default settings for the AVR, as it is shippedfrom the factory, have all inputs set for ananalog source (except for the DVD input, whichhas the Coaxial Digital Input 1 � as thedefault), with Logic 7 Music as the surroundmode, all speaker positions set to "small", and asubwoofer connected. Before using the unit, youwill probably want to change these settings formost inputs so that they are properly configuredto reflect the use of digital or analog inputs, thetype of speakers installed and the surroundmode associated with the input.

Input SetupThe first step in configuring the AVR is to selectan input. This may be done by pressing the frontpanel Input Source Selector A until thedesired input’s name appears in the MainInformation Display F, and Indicator willilluminate next to the input’s name in the frontpanel Input Indicators J. The input may alsobe selected by pressing the appropriate InputSelector on the remote control 46.

The second step is to associate one of the digitalinputs with the selected input source (if this isneeded, otherwise the selected analog input willremain). Press the Digital Input Select buttonF on the remote. Within five seconds, makeyour input selection using the K/L buttonsC on the remote until the desired digital oranalog input is shown in the Main Informa-tion Display F. Then press the Set buttonE to enter the new digital input assignment.

After the setting has been made with one input,repeat as described above with all inputs in use.The digital input associated with the inputselected can also be changed at any time laterand the AVR’s memory system will keep the set-tings until they are changed again.

Speaker SetupThis setup tells the AVR which type of speakersare in use. This is important as it adjusts thesettings that determine which speakers receivelow frequency (bass) information and whether a

Center speaker should be used or not, separatelyfor each input used. For each of these settingsuse the LARGE setting if the speakers for aparticular position are traditional full-rangeloudspeakers that are capable of reproducingsounds below 100Hz. Use the SMALL settingfor smaller, frequency-limited satellite speakersthat do not reproduce sounds below 100Hz.Note that when “small” front (left and right)speakers are used, a subwoofer is required toreproduce low frequency sounds. If you are indoubt as to which category describes yourspeakers, consult the specifications in thespeakers’ owner’s manual, or ask your dealer.

With the AVR turned on, follow these steps toconfigure the speakers:

1. Press the Speaker button � on theremote. The words SPEAKERSIZEwillappear in the Main Information Display F.

2. Press the Set button E.

3. When FRONT SPEAKER appears in theMain Information Display F press the Setbutton E to continue.

4. Press the K/L buttons C on the remoteuntil either FRONT LARGE or FRONTSMALL appears, matching the type ofspeakers you have at the left-front and right-front positions, as described by the definitionsshown in preceding section.

When SMALL is selected, low frequency frontchannel sounds will be sent only to the subwooferoutput. Note that if you choose this option andthere is no subwoofer connected, you will nothear any low frequency sounds from the frontchannels. This setting is not available with stereomode to ensure purest sound by bypassing thecrossovers of the DSP´s.

When LARGE is selected, a full-range outputwill be sent to the front left and front right out-puts. Depending on the subwoofer configuration(see below), the front left and right bass informa-tion may also be directed to a subwoofer.

Important Note: When a speaker set with twofront satellites and a passive subwoofer is used,connected to the front speaker outputs �,the fronts must be set for LARGE.

5.When you have completed your selection for thefront channels, press the Set button E, and thenpress the K/L buttons C on the remote tochange the display to CENTERSPEAKER.

6. Press the Set button E again, and use theK/L buttons C on the remote to select theoption that best describes your system based onthe Center speaker definitions shown in preced-ing section.

ENG

LISH

SYSTEM CONFIGURATION 17


When SMALL is selected, low frequency centerchannel sounds will be sent to the Fronts, if theyare set for LARGE and Sub is turned off. WhenSub is on, low frequency center channel soundswill be sent to the subwoofer only.

When LARGE is selected, a full-range outputwill be sent to the center speaker output, andwith analog and digital surround modes (exceptwith the Pro Logic II Music mode) NO centerchannel signal will be sent to the subwooferoutput.

When NONE is selected, no signal will be sentto the center channel output. The receiver willoperate in a “phantom” center channel modeand center channel information will be sent tothe left and right front channel outputs and itsbass will be sent to the subwoofer output too aslong as SUB L/R+LFE is selected in the SUB-WOOFER line in this menu (see below). Thismode is needed if no Center speaker is used.Note that for the use of Logic 7C surround modea Center speaker is needed, but Logic 7M workswell without a Center too.

7. When you have completed your selection forthe center channel, press the Set button E,and then press the K/L buttons C on theremote to change the display to SURRSPEAKER.

8. Press the Set button E again, and then usethe K/L buttons C on the remote to selectthe option that best describes your system basedon the Surround speaker definitions shown inpreceding section.

When SMALL is selected, with all digital sur-round modes low frequency surround channelsounds will be sent to the Fronts, when Sub isturned off, or to the subwoofer output when Subis on. With the analog surround modes the rearbass feed depends on the mode selected andthe setting of the sub and front speakers.

When LARGE is selected, a full-range outputwill be sent to the surround channel outputs(with all analog and digital surround modes),and, except with Hall and Theater modes, NOsurround channel bass will be sent to thesubwoofer output.

When NONE is selected, surround soundinformation will be split between the front-leftand front-right outputs. Note that for optimalperformance when no surround speakers are inuse, the Dolby 3 Stereo mode should be usedinstead of Dolby Pro Logic.

9. When you have completed your selection forthe surround channel, press the Set button E,and then press the K/L buttons C on the remote to change the display to S-W SPEAKER.

10. Press the Set button E, and then pressthe K/L buttons C on the remote to selectthe option that best describes your Subwoofersystem.

The choices available for the subwoofer positionwill depend on the settings for the otherspeakers, particularly the front left/rightpositions.

If the front left/right speakers are set toSMALL, the subwoofer will automatically beset to SUB, which is the “on” position.

If the front left/right speakers are set toLARGE, three options are available:

• If no subwoofer is connected to the AVR, pressthe arrow buttons C so that SUB NONEappears in the display. When this option isselected, all bass information will be routed tothe front left/right “main” speakers.

• If a subwoofer is connected to the AVR, youhave the option to have the front left/right“main” speakers reproduce bass frequencies atall times, and have the subwoofer operate onlywhen the AVR is being used with a digital sourcethat contains a dedicated Low Frequency Effects,or LFE soundtrack. This allows you to use bothyour main and subwoofer speakers to takeadvantage of the special bass created for certainmovies. To select that option press the arrowbuttons C so that SUB LFE appears in thedisplay.

• If a subwoofer is connected and you wish touse it for bass reproduction in conjunction withthe main front left/right speakers, regardless ofthe type of program source or surround modeyou are listening to, press the arrow buttonsC so that SUB L/R+LFE appears in thedisplay. When this option is selected, a “com-plete” feed will be sent to the front left/right“main” speakers, and the subwoofer will receivethe front left and right bass frequencies underthe crossover frequency 80 Hz, additionally tothe LFE soundtrack (see above).

11. When all speaker selections have been madefor the input selected, press the Set button Etwice or simply wait for three seconds until thedisplay returns to the normal mode.

To assist in making these settings, the icons inthe Speaker/Channel Input Indicators 5will change as the speaker type is selected ateach position. When only the inner icon box islit, the speaker is set for “small.” When the innerbox and the two outer boxes with circles insidethem are lit, the speaker is set for “large." Whenno indicator appears at a speaker location, thatposition is set for “none” or “no” speaker.

As an example, in the Figure below, the left frontand right front speakers are set for “large,” thecenter, left surround and right surround speakersare set for small, and a subwoofer is set.

Surround SetupOnce the speaker setup has been completed, thenext setup step is to set the surround mode youwish to use with each input. Since surroundmodes are a matter of personal taste, feel free toselect any mode you wish – you may change itlater. The Surround Mode chart on page 22 mayhelp you select the mode best suited to theinput source selected. However, to make it easierto establish the initial parameters for the AVR, itis best to leave the default setting of Logic 7Music mode for most analog inputs and DolbyDigital for inputs connected to digital sources. Inthe case of inputs such as a CD Player, TapeDeck or Tuner, you may wish to set the mode toStereo, if that is your preferred listening modefor standard stereo sources, where it is unlikelythat surround encoded material will be used.

To set the surround mode you wish to use withthe input selected, press the Surround ModeSelector button 6 on the front or 9 and theK/L buttons C on the remote until thedesired surround mode´s name appears in theMain Information Display F.

As the modes are changed, Indicator will illuminate next to the mode names in theSurround Mode Indicators D on the frontpanel.

Note that Dolby Digital and DTS will only appearas choices when a digital input has been selected.

L RC

SL SRLFE

After the surround mode setting has been madewith the current input, repeat the setting with allinputs you will use. The surround mode can alsobe changed at any time later, and the AVR’smemory system will keep the settings for theinput selected, until they are changed again.

Configuring the Surround Off(Stereo) Modes

For superior reproduction of two-channelprogram materials, the AVR offers two Stereomodes: an analog Stereo-Direct mode thatbypasses the digital signal processing circuitry fora completely analog signal path that preservesthe purity of the original signal, and a digitalmode that is capable of providing bassmanagement for optimal distribution of the lowfrequencies between smaller speakers and asubwoofer.

Stereo-Direct (Bypass) ModeWhen the analog Stereo-Direct mode is selectedby pressing the Stereo Mode Selector until SURROUND OFF appears in the MainInformation Display F and the SurroundMode Indicator D for Surround Off is lit, theAVR will pass the analog source material directlythrough to the front left and right speakers,bypassing the digital processing circuitry.

In this mode, the front left and right speakers willautomatically be configured as LARGE; it isnot possible to configure these speakers asSMALL.

When the AVR is in the Stereo Bypass mode youmay still configure the subwoofer output so thatit is either turned off, with a full-range signalgoing to the front left/right speakers, or you mayconfigure it so that the subwoofer feed isactivated. The factory default setting is to havethe subwoofer turned off for this mode, but youmay change that setting by following thesesteps:

1. Press the Speaker Button �.

2. Press the Set Button E to activate theconfiguration menu.

3. Press the K/L Buttons C on the remoteto select the desired option. SUB NONE turnsoff the feed to the subwoofer, while SUB<L+R> turns it on.

4. When the desired setting has been entered,press the Set Button E to return to normaloperation.

Stereo-Digital ModeWhen the Stereo-Direct (Bypass) mode is in use afull range signal is always sent to the frontleft/right speakers. By its nature, that option doesnot pass the signal through the AVR’s digitalsignal processing, creating the requirement forfull-range speakers. If your front speakers arebandwidth limited, “satellite”speakers, werecommend that you do NOT use the Bypassmode, but rather use the DSP SURROUNDOFFmode for stereo listening.

To listen to programs in the two-channel stereomode while taking advantage of the bassmanagement system, press the Stereo ModeSelector until SURROUND OFFappears in the Main Information Display Fand the DSP and SURR. OFF SurroundMode Indicators D both light up. When onlythe SURR. OFF Surround ModeIndicators D is lit you are in the Stereo-Direct(Bypass) mode.

When this mode is in use, the front left/rightspeakers and subwoofer may be configured tomeet the requirements of your specific speakersusing the steps shown in the Speaker Setupsection on page 16.

Delay Settings Only for the Dolby or DTS modes, you will needto adjust the delay time setting. Note that thedelay time is not adjustable for any other modes.

Due to the different distances between thelistening position for the front channel speakersand the surround speakers, the amount of time ittakes for sound to reach your ears from the frontor surround speakers is different. You maycompensate for this difference through the use ofthe delay settings to adjust the timing for thespecific speaker placement and acousticconditions in your listening room or hometheater.

The factory setting (see Surround Mode Chartpage 22) is appropriate for most rooms, butsome installations create an uncommon distancebetween the front and surround speakers thatmay cause the arrival of front channel sounds tobecome disconnected from surround channelsounds.

To resynchronize the front, center and surroundchannels, follow these steps:

1. Measure the distance from the listening/viewing position to the front speakers inmeters.

2. Measure the distance from the listening/viewing position to the surround speakers.

3. Press the Delay Button �.

4. When FRONT DELAY appears in theMain Information Display F press the SetButton E.

5. Press the K/L Buttons C on the remoteto enter the distance from the front left/rightspeakers to your listening position. Press the SetButton E when this is complete.

6. Press the K/L Buttons C on the remoteso that CENTER DELAY appears in theMain Information Display F and press theSet Button E.

7. Press the the K/L Buttons C on theremote to enter the distance from the centerspeaker your listening position. Press the SetButton E when this is complete.

. Press the K/L Buttons C on the remoteso that SURR DELAY appears in the LowerDisplay Line and press the Set Button E.

9. Press the the K/L Buttons C on theremote to enter the distance from the surroundspeakers to your listening position. Press the Set Button E when this is complete.

10. When all adjustments have been made, theunit will return to normal operation in fiveseconds.



ENG

LISH

SYSTEM CONFIGURATION 19


Night Mode SettingsThe Night mode is a feature of Dolby Digital thatuses special processing to preserve the dynamicrange and full intelligibility of a movie soundtrack while reducing the peak level. This preventsabruptly loud transitions from disturbing others,without reducing the sonic impact of a digitalsource. Note that the Night mode is onlyavailable when the Dolby Digital surround modeis selected.

To adjust the Night mode setting press the InputSource Selector A on the front or 4 on theremote and select an input that is associatedwith a digital input and the Dolby Digitalsurround mode.

Next press the Night button A on the remote.When the button is pressed, the words D-RANGE (Dynamic Range) followed by thecurrent setting (MID, MAX, OFF) will appear inthe Main Information Display F. Press theK/L buttons C within five seconds to selectthe desired setting:

OFF: When OFF is shown in the display, theNight mode will not function.

MID: When MID is shown in the display, a mildcompression will be applied.

MAX: When MAX is shown in the display, amore severe compression algorithm will beapplied.

When you want to use the Night mode feature,we recommend that you select the MID settingas a starting point and change to the MAXsetting later, if desired.

Output Level AdjustmentOutput level adjustment is a key part of theconfiguration process for any surround soundproduct. It is particularly important for a DolbyDigital receiver such as the AVR, as correctoutputs will ensure that you hear sound trackswith the proper directionality and intensity.

NOTE: Listeners are often confused about theoperation of the surround channels. While someassume that sound should always be comingfrom each speaker, most of the time there will belittle or no sound in the surround channels. Thisis because they are only used when a moviedirector or sound mixer specifically places soundthere to create ambiance, a special effect or tocontinue action from the front of the room tothe rear. When the output levels are properly setit is normal for surround speakers to operateonly occasionally. Artificially increasing thevolume to the rear speakers may destroy theillusion of an enveloping sound field thatduplicates the way you hear sound in a movietheater or concert hall.

IMPORTANT NOTE: The output level can beadjusted for each digital and analog surroundmode separately. This allows you to compensatefor level differences between speakers, that mayalso vary with the surround mode selected, or toincrease or decrease the level of certain speakersintentionally, depending on the surround modeselected. Note that adjustments made for anysurround mode are effective with all inputsassociated with that surround mode.

Before beginning the output level adjustmentprocess, make certain that all speakerconnections have been properly made. Thesystem volume should be turned down at first.

For the easiest set-up, follow these steps whileseated in the listening position that will be usedmost often:

1. Make certain that all speaker positions havebeen properly configured for their “large” or“small” settings (as outlined above) and turnoff the OSD system if it is in use.

2. Adjust the volume so that it is at -15, asshown in the on-screen display or MainInformation Display F.

To adjust and calibrate the output levels, followthese steps. For accurate calibration, it is a goodidea to make these adjustments while seated inyour favorite listening position. As the adjust-ment must be made for each surround mode, it isbest to select any input associated with anyDolby Pro Logic II mode, make the adjustment forthat surround mode, then step through all inputsyou´re using (and thus through all surroundmodes associated with the inputs) and repeatthe adjustment when any surround modeappears that has not yet been adjusted.

1. Select any input associated with any Dolby ProLogic II surround mode by pressing the InputSource Selector A4 until the Pro Logic IISurround Mode Indicator D on thefrontdisplay lights up.

2. Press the Test Tone button 7 on theremote. The words TEST-T FL 0DB willappear in the Main Information Display F.

3. The test noise will immediately begin tocirculate in the speakers in a clockwise rotation,pausing at each position for two seconds. As thetest noise rotates the speaker positions FL, C,FR, SR, SL (Front Left, Center, Front Right,Surround Right, Surround Left) will be shown inthe Main Information Display F. As anadded assist, while the test noise is circulating,the proper channel position will also be indicatedin the Speaker/Channel Indicators 5 by ablinking letter within the correct channel. Turn upthe volume now until you can hear the noiseclearly.

IMPORTANT NOTE: Because this test noise willhave a much lower level than normal music, thevolume must be lowered after the adjustmentfor all channels is made, BEFORE you turn thetest tone off.

NOTE: This is a good time to verify that thespeakers have been properly connected. As thetest noise circulates, listen to make certain thatthe sound comes from the speaker positionshown in the Main Information Display. If thesound from a speaker location does NOT matchthe position indicated in the display, turn theAVR off using the Main Power Switch � andcheck the speaker wiring to make certain thateach speaker is connected to the correct outputterminal.

After checking for speaker placement, let thetest noise circulate again, and listen to seewhich channels sound louder than the others.Using the front left speaker as a reference, pressthe K/L buttons C on the remote to bringall speakers to the same volume level. Note thatwhen one of the K/L buttons is pushed, thetest noise circulation will pause on the channelbeing adjusted to give you time to make theadjustment. When you release the button, the circulation will resume after five seconds.

Continue to adjust the individual speakers untilthey all have the same volume. Note thatadjustments should be made with the K/Lbuttons C on the remote only, NOT the mainvolume controls.

When all channels have the same output level,turn the Volume I� down to about –40dB,otherwise the listening level may be too high assoon as the source’s music starts to play.Afterwards press the Test Tone Selector 7button again to turn the test tone off andcomplete the process.

IMPORTANT NOTE: The Output leveladjustment made will be effective for thesurround mode currently selected, also whenother inputs are selected using the samesurround mode. To adjust the output level withall other surround modes used, step through allinputs you´re using by pressing the SourceSelector buttons A on the front panel or theappropriate Input Selectors 4 on the remote.When the indicator for any surround mode forwhich the level adjustment has not yet beenmade lights in the Main Information DisplayF or its Indicator will illuminate in theSurround Mode Indicators field D, repeatthe level adjustment described above. This willalso allow you to compensate level differencesbetween speakers, that may be different witheach surround mode, or to increase or decreasethe level of certain speakers intentionally,depending on the surround mode selected.

Once the settings outlined on the previouspages have been made, the AVR is ready foroperation. While there are some additionalsettings to be made, these are best done afteryou have had an opportunity to listen to avariety of sources and different kinds of programmaterial. These advanced settings are describedon page 30 of this manual. In addition, any ofthe settings made in the initial configuration ofthe unit may be changed at any time.As you add new or different sources or speakers,or if you wish to change a setting to betterreflect your listening taste, simply follow theinstructions for changing the settings for thatparameter as shown above. Note that anysettings changed at any time, will be stored inmemory in the AVR, also if it´s turned offcompletely, unless it will be reset (see page 34).Having completed the setup and configurationprocess for your AVR, you are about toexperience the finest in music and home theaterlistening. Enjoy!



ENG

LISH

OPERATION 21

Operation

Basic Operation

Once you have completed the setup andconfiguration of the AVR, it is simple to operateand enjoy. The following instructions should befollowed for you to maximize your enjoyment ofyour new receiver:

Turning the AVR On or Off• When using the AVR for the first time, you mustpress the Main Power Switch � on the frontpanel to turn the unit on. This places the unit in aStandby mode, as indicated by the orange color ofthe Power Indicator 2. Once the unit is inStandby, you may begin a listening session bypressing the System Power Control 1 or theSource button A on the front panel or the AVRSelector 5. Note that the Power Indicator2 will turn blue. This will turn the unit on andreturn it to the input source that was last used.The unit may also be turned on from Standby bypressing any of the Source Selector buttons onthe remote 456�.

NOTE: After pressing one of the Input Selectorbuttons 4 to turn the unit on, press the AVRSelector 5 to have the remote control the AVRfunctions.

To turn the unit off at the end of a listeningsession, simply press the System PowerControl 1 on the front panel or the PowerOff Button 3 on the remote.

When the remote is used to turn the unit “off” itis actually placing the system in a Standby mode,as indicated by the orange color of the PowerIndicator 2.

When you will be away from home for anextended period of time it is always a good ideato completely turn the unit off with the frontpanel Main Power Switch �.

NOTE: All preset memories may be lost if theunit is left turned off with the Main PowerSwitch � for more than two weeks.

Using the Sleep Timer• To program the AVR for automatic turn-off,press the Sleep Button 8 on the remote. Eachpress of the button will increase the time beforeshut down in the following sequence:

When the programmed sleep time has elapsed,the unit will automatically turn off (to Standbymode). Note that the front panel display will dimto one half brightness when the Sleep functionis programmed. To cancel the Sleep function,press and hold the Sleep Button 8 until theinformation display returns to normal brightnessand the SLEEP OFFmessage appears in theMain Information Display F.

Source Selection

• To select a source, press any of the Source Selector buttons on the remote456�.

NOTE: After pressing one of the Input Selectorbuttons 4 you must press the AVR Selector5 to have the remote control the AVR functions.

• The input source may also be changed bypressing the front-panel Input SourceSelector button A. Each press of the buttonwill move the input selection through the list ofavailable inputs.

• As the input is changed, the AVR will auto-matically switch to the digital input (if selected),surround mode and speaker configuration thatwere entered during the configuration processfor that source.

• The front-panel Video 3 Inputs H, OpticalDigital 3 Input 4 or the Coaxial Digital 3Input G may be used to connect a device suchas a video game or camcorder to your homeentertainment system on a temporary basis.

• As the input source is changed, the new inputname will appear in the Main InformationDisplay F and a green LED will light next tothe selected input’s name in the front-panelInput Indicators J.

• When a pure audio input (CD, Tuner, Tape,6/8 Channel Input) is selected, the last videoinput used remains routed to the Video Out-puts �� and Video Monitor Output .This permits simultaneous viewing and listeningto different sources.

• When a Video source is selected, its audiosignal will be fed to the speakers and the videosignal for that input will be routed to theappropriate Monitor Output Jack and willbe viewable on a TV monitor connected to theAVR. If a component video source is connected tothe Video 1 � or Video 2 ComponentInputs, it will be routed to the ComponentVideo Outputs �. Make certain that your TV isset to the proper input to view the appropriatevideo signal (composite, S-Video or componentvideo, see Notes for S-Video on page 13).

Controls and Use of Headphones

• Adjust the volume to a comfortable level usingthe front panel Volume Control I or remoteVolume Up/Down � buttons.

• To temporarily silence all speaker outputspress the Mute button �. This will interruptthe output to all speakers and the headphonejack, but it will not affect any recording ordubbing that may be in progress. Press theMute button � again to return to normaloperation.

• During a listening session you may wish toadjust the Bass Control and Treble Controlto suit your listening tastes or room acoustics.

• To set the output of the AVR so that the out-put is “flat,” with the Tone controls and theBalance control de-activated, press the ToneMode button � button once or twice so thatthe words Tone Out appear momentarily inthe Main Information Display F. To returnthe tone controls to an active condition, pressthe Tone Mode � button once or twice sothat the words Tone Inmomentarily appearin the Main Information Display F.

• To change the Bass or Treble Control settingspress the Tone Mode Button � until thewords Bass or Treble appear momentarily in theMain Information Display F. Press the SetButton E followed by the A/B ButtonsD� to adjust the setting. When done, pressthe Tone Mode Button � again to exit theTone Mode Menu.

• For private listening, plug the 6.3 mm stereophone plug from a pair of stereo headphonesinto the front panel Headphone Jack 3. Notethat when the headphone’s plug is connected,the word HEADPHONE will scroll onceacross the Main Information Display F andall speakers will be silenced. When theheadphone plug is removed, the audio feed tothe speakers will be restored.

• When the headphones are in use, you maytake advantage of the Dolby Headphone modesto bring added spaciousness to headphonelistening. Press the Dolby Mode SelectButton or the Surround Mode GroupSelector 6 to cycle through the three DolbyHeadphone modes to select the one that youprefer.

Surround Mode Selection

One of the most important features of the AVR isits ability to reproduce a full multichannelsurround sound field from digital sources, analogmatrix surround encoded programs and standardstereo or even mono programs. In all, a total offifteen listening modes are available on the AVR.

Selection of a surround mode is based onpersonal taste, as well as the type of programsource material being used.

For example, motion pictures, CD’s or TVprograms bearing the logo of one of the majorsurround encoding processes, such as DolbySurround should be played in either the DolbyPro Logic II Movie (with movies) or Music (withmusic) surround mode or with the Harman Kardon´s exclusive Logic 7 Movie Mode,to create a full range discrete 5.1 channelsurround signal from surround encodedprograms with a stereophonic left and right rearsignal, just as it was recorded in real life (e.g.

90min

80min

70min

60min

50min

40min

30min

20min

10min OFF

Surround Mode Chart

MODE FEATURES DELAY TIME RANGE

DOLBY DIGITAL Available only with digital input sources encoded with Dolby Digital data. It provides Center: 0 ms – 5 msup to five separate main audio channels and a special dedicated Low Frequency Effects Initial Setting – 0 mschannel. Surround: 0 ms –15 ms

Initial Setting – 0 ms

DTS 5.1 When the speaker configuration is set for 5.1-channel operation, the DTS 5.1 mode is available when DVD, audio-only music or laserdiscs encoded with DTS data are played.DTS 5.1 provides up to five separate main audio channels and a special dedicated low-frequency channel.

DOLBY PRO LOGIC II Dolby Pro Logic II is the latest version of Dolby Laboratory’s benchmark surround technologyMOVIE that decodes full-range, discrete left, center right, right surround and left surround channels MUSIC from matrix surround encoded programs and conventional stereo sources when DOLBY PRO LOGIC an analog input or a digital input with PCM or Dolby Digital 2.0 recordings is in use. The

Dolby Pro Logic II Movie mode is optimized for movie soundtracks that are recorded with matrix surround, by creating separate center, rear left and rear right signals. while the Pro Logic II Music mode should be used with musical selections that are recorded with matrix surround or even withnormal stereo mode, creating separate rear left and rear right signals in any case.The Pro Logic II mode creates compelling five-channel surround sound from conventional stereo recordings.

Logic 7 Cinema Exclusive to Harman Kardon for AV receivers, Logic 7 is an advanced mode that extracts the Logic 7 Music maximum surround information from either surround-encoded programs or conventional stereo Logic 7 Enhance material. Depending on the number of speakers in use and the selection made in the SURROUND

SELECTmenu, the “5.1” versions of Logic 7 modes are available when the 5.1 option is chosen,while the “7.1” versions of Logic 7 produce a full sound field presentation, including back surround speakers when the “6.1/7.1” option is chosen. The Logic 7 C (or Cinema) mode should be used with any source that contains Dolby Surround or similar matrix encoding. Logic 7 C delivers increased center-channel intelligibility, and more accurate placement of sounds with fades and pans that are much smoother and more realistic than with former decoding techniques. The Logic 7 M or Music mode should be used with analog or PCM stereo sources. Logic 7 M enhances the listening experience by presenting a wider front soundstage and greater rear ambience. Both Logic 7 modes also direct low-frequency information to the subwoofer (if installed and configured) to deliver maximum bass impact. The Logic 7 E (or Enhance) mode is an extension of the Logic 7 modes that is primarily used with musical programs and is available with the 5.1 surround mode option selected only. Logic 7 E adds additional bass enhancement that circulates low frequencies in the 40Hz to 120Hz range to the front and surround speakers to deliver a less localized soundstage that appears broader and wider than when the subwoofer is the sole source of bass energy.

DTS 96/24 DTS 96/24 is a high-resolution format that uses a 96kHz sampling rate with 24 bits to produce extended information that improves the harmonics of the source material.The AVR is capable of automatically detecting and decoding DTS 96/24 materials and delivering them as the artist intended.

DOLBY 3 STEREO Uses the information contained in a surround encoded or two channel stereo program to No surround channels create center channel information. In addition, the information that is normally sent to the rear channel surround speakers is carefully mixed in with the front left and front right channels for increased realism. Use this mode when you have a center channel speaker but no surround speakers.

THEATER The THEATER mode creates a sound field that resembles the acoustic feeling Delay time not adjustable of a standard live performance theater, with stereo and even pure mono sources.

HALL 1 The two Hall modes create sound fields that resemble a small (HALL 1) or Delay time not adjustableHALL 2 medium sized (HALL 2) concert hall, with stereo and even pure mono sources.

Operation

22 OPERATION

ENG

LISH

OPERATION 23

Operation

Surround Mode Chart

MODE FEATURES DELAY TIME RANGE

5-Channel Stereo This mode takes advantage of multiple speakers to place a stereo signal at both the front and No delay is available for back of a room. Ideal for playing music in situations such as a party, it places the same signal this modeat the front-left and surround-left, and at the front-right and surround-right speakers. The centerchannel is fed a summed mono mix of the in-phase material of the left and right channels.

Surround Off (Stereo) These modes turn off all surround processing and present the pure left- and right-channel No surround channels Surround Off (Bypass) presentation of two-channel stereo programs. The Surround Off (Bypass) mode may only be DSP Surround Off used with analog source inputs, as it preserves the analog format of the audio signal for its

entire path of travel through the receiver to the speaker and subwoofer outputs, bypassing all digital processing. Digital bass management is not available in Surround Off mode. The DSP Surround Off mode can be used with either an analog or digital input, as the signal undergoes digital bass management to optimize the distribution of the low frequencies between the main speakers and a subwoofer.

Dolby Virtual Speaker Dolby Virtual Speaker technology uses a next-generation advanced algorithm to reproduce the No surround channelsReference dynamics and surround sound effects of a precisely placed 5.1-channel speaker system using only Wide front left and right speakers. In the Reference Mode, the apparent width of the sound across

the front image is defined by the distance between the two speakers. The Wide Mode provides a wider, more spacious front image when the two speakers areclose together.

Dolby Headphone Dolby Headphone enables ordinary stereo headphones to portray the sound of a five-speaker No surround channelsDH surround-playback system.

24 OPERATION

Operation

sound being recorded from left rear side will beheard from that side only, for more details seechart on page 22).

When no rear speakers are in use, the Dolby 3Stereo mode should be selected with all surroundrecordings.

Note that when Dolby Digital 2.0 signals (e.g."D.D. 2.0" tracks from DVD), that are encodedwith Dolby Pro Logic information, are receivedvia any digital input, the Dolby Pro Logic II Moviemode will be selected automatically (in additionto the Dolby Digital mode) and will decode a fullrange 5.1 channel surround sound even fromthose recordings (see also "Dolby Digital" onpage 25).

To create wide, enveloping sound fieldenvironments and defined pans and flyovers withall analog stereo recordings select the Dolby ProLogic II Music mode or Harman Kardon’sexclusive Logic 7 Music mode for a dramaticimprovement in comparison to the Dolby ProLogic (I) mode of former times.

NOTE: Once a program has been encoded withmatrix surround information, it retains thesurround information as long as the program isbroadcast in stereo. Thus, movies with surroundsound may be decoded via any of the analog sur-round modes such as Dolby Pro Logic II or Logic 7,when they are broadcast via conventional TVstations, cable, pay TV and satellite transmission.In addition, a growing number of made-for-televi-sion programs, sports broadcasts, radio dramasand music CDs are also recorded in surroundsound. You may view a list of these programs atthe Dolby Laboratories Web site atwww.dolby.com.

Even when a program is not listed as carryingintentional surround information, you may findthat the Dolby Pro Logic II, Dolby 3 Stereo or Logic 7 modes often deliver enveloping surroundpresentations through the use of the naturalsurround information present in all stereorecordings.

However, for stereo programs without anysurround information the Theater, Hall and 5CHStereo modes should be tried (effective particularlywith old ”extreme” stereo recordings) and formono programs, we suggest that you try theTheater or Hall modes.

Surround modes are selected using either thefront panel controls or the remote. To select asurround mode from the front panel, press theSurround Mode Group Selector Button 6to scroll through the list of available surroundgroups (for example, any Dolby mode or Logic 7mode). Next press the Surround ModeSelector Button C to choose the specificmode within the desired group (for example,within the Dolby mode group the options areDolby Pro Logic, Dolby Pro Logic II Music, DolbyPro Logic II Movies and Dolby 3 Stereo). To selecta surround mode using the remote, any of thesurround mode selector buttons 9�� until the desired mode appears. Asyou press the buttons, the Surround mode namewill appear in the Main Information DisplayF. As the surround mode changes, a blue LEDwill light next to the current mode in theSurround Mode Indicators list D on thefront panel. Regard that any time a surroundmode is changed it remains associated with theinput just selected until another choice is made.

NOTE: The name of each Surround Mode willscroll through the Main Information DisplayF while the modes are being selected. To avoidexiting from the surround mode selectionprocess, be certain to push the K/L buttonsC while a mode name is still visible.

Note that the Dolby Digital or DTS modes mayonly be selected when a digital input is in use. Inaddition, when a digital source is present, theAVR will automatically select and switch to thecorrect mode (Dolby Digital or DTS), regardless ofthe mode that has been previously selected. Formore information on selecting digital sources, seethe following section of this manual.

To listen to a program in traditional two channelstereo, using the front left and front rightspeakers only (plus the subwoofer if installed andconfigured), follow the instructions shown abovefor using the remote until SURR OFF appearsin the Main Information Display F.

Digital Audio Playback

Digital audio is a major advancement over olderanalog matrix surround systems. It delivers fivediscrete channels: left front, center, right front, leftsurround and right surround. Each channelreproduces full frequency range (20Hz to 20kHz)and offers dramatically improved dynamic rangeand significant improvements to signal-to-noiseratios. In addition, digital systems have thecapability to deliver an additional channel that isspecifically devoted to low frequency information.This is the “.1” channel referred to when you seethese systems descibed as “5.1”. The bass channelis separate from the other channels, but since it isintentionally bandwidth limited, sound designershave given it that unique designation.

Dolby Digital Dolby Digital (originally known as AC-3®) is astandard part of DVD, and is available onspecially encoded LD discs and satellitebroadcasts and it is a part of the new high-definition television (HDTV) system.

Note that an optional, external RF demodulatoris required to use the AVR to listen to the DolbyDigital sound tracks available on laser discs.Connect the RF output of the LD player to thedemodulator and then connect the digital outputof the demodulator to the Optical or Coaxialinputs ��4G of the AVR. No demodulatoris required for use with DVD players or DTS-encoded laser discs.

DTSDTS is another digital audio system that iscapable of delivering 5.1 audio. Although bothDTS and Dolby Digital are digital, they usedifferent methods of encoding the signals, andthus they require different decoding circuits toconvert the digital signals back to analog.

DTS-encoded sound tracks are available on selectDVD and LD discs, as well as on special audio-only DTS CDs. You may use any LD, DVD or CDplayer equipped with a digital output to playDTS-encoded special audio-only CDs with theAVR, but DTS-LDs can be played on LD playersand DTS-DVDs on DVD players only. All that isrequired is to connect the player’s output toeither the Optical or Coaxial input on the rearpanel ��or front panel 4G.

In order to listen to DVDs encoded with DTSsound tracks, the DVD player must be compatiblewith the DTS signal as indicated by a DTS logoon the player’s front panel. Note that early DVDplayers may not be able to play DTS- encodedDVDs. This does not indicate a problem with theAVR, as some players cannot pass the DTS signalthrough to the digital outputs. If you are in doubtas to the capability of your DVD player to handleDTS DVDs, consult the player’s owner’s manual.

Please note that some DVD players are shippedwith their output set for Dolby Digital only. Toinsure that DTS data is being sent to the AVR,please check the setup menu system on yourDVD player to make certain that DTS data outputis enabled.

PCM Audio PlaybackPCM (Pulse Code Modulation) is the non-compressed digital audio system used for com-pact discs, Non-Dolby Digital/DTS Laserdiscs andsome special PCM encoded DVDs. The digitalcircuits in the AVR are capable of high qualitydigital-to-analog decoding, and they may beconnected directly to the digital audio output ofyour CD/DVD or LD player (LD only for PCM orDTS programs, for Dolby Digital laser discs an RFadapter is needed, see ”Dolby Digital” above).

ENG

LISH

OPERATION 25

Operation

Connections may be made to the Optical orCoaxial inputs �� on the rear panel or frontpanel 4G.

To listen to a PCM digital source, first select theinput for the desired source (e.g., CD) to feed itsvideo signal (if any) to the TV monitor and toprovide its analog audio signal for recording.Next press the Digital Select button F andthen use the K/L buttons C on the remoteuntil the desired choice appears in the MainInformation Display F, then press the Setbutton E to confirm the choice.

When a PCM source is playing, a brief messagePCM will appear in the Main InformationDisplay F. During PCM playback you mayselect any surround mode as described on pages21, 22 and 23 except Dolby Digital or DTS.

Selecting a Digital Source

To utilize either digital mode you must haveproperly connected a digital source to the AVR.Connect the digital outputs from DVD players,HDTV receivers, satellite systems or CD players tothe Optical or Coaxial inputs on the rear orfront panel ��4G. In order to provide abackup signal and a source for analog stereorecording, the analog outputs provided on digitalsource equipment should also be connected totheir appropriate inputs on the AVR rear panel(e.g., connect the analog stereo audio outputfrom a DVD to the DVD inputs � on the rearpanel when you connect the source’s digital outputs).

When playing a digital source such as DVD, firstselect its input using the remote or front panelcontrols as outlined in this manual in order tofeed its video signal (if any) to the TV monitorand to provide its analog audio signal forrecording. When the digital input appropriatewith the DVD player is not selected automatically(due to the input settings made earlier during thesystem configuration, see page 16), select thedigital source by pressing the Digital InputSelector button F and then using the K/Lbuttons C on the remote to choose any of the OPTICAL (OPT) or COAXIAL(COAX) inputs, as they appear in the MainInformation Display F. When the digitalsource is playing, the AVR will automaticallydetect whether it is a multichannel Dolby Digital,DTS source or a conventional PCM signal, whichis the standard output from CD players.

Digital Status Indicators

When a digital source is playing, the AVR sensesthe type of bitstream data that is present. Usingthis information, the correct surround mode willautomatically be selected. For example, DTS bit-streams will cause the unit to switch to DTSdecoding, and Dolby Digital bitstreams will enableDolby Digital decoding. When the unit senses

PCM data, from CDs and LDs and some musicDVDs or certain tracks on normal DVDs, it willallow the appropriate surround mode to beselected manually. Since the range of availablesurround modes depends on the type of digitaldata that is present, the AVR uses a variety ofindicators to let you know what type of signal ispresent. This will help you to understand thechoice of modes and the input channels recordedon the disc.

When a digital source is playing, the AVR willdisplay a variety of messages to indicate the typeof bitstream received. These messages willappear shortly after an input or surround mode ischanged, and will remain in the MainInformation Display F for about fiveseconds before the display returns to the normalsurround mode indication.

Surround Mode Types

For Dolby Digital and DTS sources, a three digitindication will appear, showing the number ofchannels present in the data. An example of thistype of display is 3/2/.1.

The first number indicates how many discretefront channel signals are present.

• A 3 tells you that separate front left, center andfront right signals are available. This will bedisplayed for Dolby Digital 5.1 and DTS 5.1programs.

• A 2 tells you that separate front left and rightsignals are available, but there is no discretecenter channel signal. This will be displayed forDolby Digital bit streams that have stereoprogram material.

• A 1 tells you that there is only a mono channelavailable in the Dolby Digital bitstream.

The middle number indicates how many discretesurround channel signals are present.

• A 2 tells you that separate surround left andright signals are available. This will bedisplayed for Dolby Digital 5.1 and DTS 5.1programs.

• A 1 tells you that there is only a single,surround encoded surround channel. This willappear for Dolby Digital bit streams that havematrix encoding.

• A 0 indicates that there is no surround channelinformation. This will be displayed for two-channel stereo programs.

The last number indicates if there is a discreteLow Frequency Effects (LFE) channel. This is the“.1” in the common abbreviation of “5.1” soundand it is a special channel that contains only bassfrequencies.

• A .1 tells you that an LFE channel is present.This will be displayed for Dolby Digital 5.1 andDTS 5.1 programs, as available.

• A 0 indicates that there is no LFE channelinformation available. However, even whenthere is no dedicated LFE channel, lowfrequency sound will be present at thesubwoofer output when the speakerconfiguration is set to show the presence ofsubwoofer.

An UNLOCKmessage may appear in theLower Display Line F. This is your indicationthat the digital audio data stream has been inter-rupted or is no longer present. When that occurs,the unit’s digital signal processor has no signal tolock onto, and is thus “unlocked.” You may seethis message when a DVD is first started until thestream is playing and the processor determineswhich mode to apply; or any time the datastream is stopped or paused, such as when themenus of some discs are displayed or when theplayer is switching between the different sectionsof a disc. You may also see the message when asatellite receiver, cable set-top or HDTV tuner isin use if the digital audio is temporarilyinterrupted when channels are changed or whena cable box switches from a channel with adigital data stream to a channel with analogaudio only. The UNLOCKmessage is normal,and does not indicate any problem with yourreceiver. Rather, it tells you that the incomingdata has simply been paused or is not present fora variety of possible reasons.

When Dolby Digital 3/2/.1 or DTS 3/2/.1 signalsare being played, the AVR will automaticallyswitch to the proper surround mode, and noother processing may be selected. When a DolbyDigital signal with a 3/1/0 or 2/0/0 signal isdetected you may select any of the Dolbysurround modes.

It is always a good idea to check the readout forthe channel data to make certain that it matchesthe audio logo information shown on the back ofa DVD package. In some cases you will seeindication for “2/0/0” even when the disccontains a full 5.1, or 3/2/.1 signal. When thishappens, check the audio output settings foryour DVD player or the audio menu selections forthe specific disc being played to make certainthat the player is sending the correct signal tothe AVR.

In addition to the Bitstream Indicators, theAVR features a set of unique channel input indi-cators that tell you how many channels of digitalinformation are being received and if the digitalsignal is interrupted.

26 OPERATION

These indicators are the L/C/R/SL/SR/LFE lettersthat are inside the center boxes of theSpeaker/Channel Input Indicators in thefront panel 5. When a standard analog stereoor matrix surround signal is in use, only the “L”and “R” indicators will light, as analog signalshave only left and right channels, respectively,even surround recordings, carry surroundinformation on the left and right channels only.

Digital signals, however, may have one to sixseparate channels, depending on the programmaterial, the method of transmission and theway in which it was encoded. When a digitalsignal is playing, the letters in these indicatorswill light in response to the specific signal beingreceived. It is important to note that althoughDolby Digital, for example, is referred to as a“5.1” system, not all Dolby Digital DVD or audiotracks selected on DVD or other Dolby Digitalprograms are encoded for 5.1. Thus, it is some-times normal for a DVD with a Dolby Digitalsoundtrack to trigger e.g. only the “L” and “R”indicators.

NOTE: Many DVD discs are recorded with both“5.1” and “2.0” versions of the same sound-track, the ”2.0” version often is used with otherlanguages. When playing a DVD, always becertain to check the type of material on the disc.Most discs show this information in the form of alisting or icon on the back of the disc jacket.When a disc does offer multiple soundtrackchoices you may have to make some adjustmentsto your DVD player (usually with the “AudioSelect” button or in a menu screen on the disc)to send a full 5.1 feed to the AVR or to select theappropriate audio track and thus language(”2.0” audio tracks can be played with all ProLogic II modes, see "Dolby Digital" on page 25).It is also possible for the type of signal feed tochange during the course of a DVD playback. Insome cases the previews of special material willonly be recorded in 2.0 audio, while the mainfeature is available in 5.1 audio. As long as yourDVD player is set for 6-channel output, the AVRwill automatically sense changes to the bitstreamand channel count and reflect them in these indi-cators.

The letters used by the Speaker/Channel InputIndicators 5 also flash to indicate when abitstream has been interrupted. This will happenwhen a digital input source is selected before theplayback starts, or when a digital source such asa DVD is put into a Pause mode. The flashingindicators remind you that the playback hasstopped due to the absence of a digital signaland not through any fault of the AVR. This isnormal, and the digital playback will resumeonce the playback is started again.

Night Mode

A special feature of Dolby Digital is the Nightmode, which enables Dolby Digital input sourcesto be played back with full digital intelligibiltywhile reducing the maximum peak level andlifting the low levels by 1/4 to 1/3. This preventsabruptly loud transitions from disturbing otherswithout reducing the impact of the digital source.The Night mode is available only when DolbyDigital mode is selected.

The Night mode may be engaged when a DolbyDigital DVD is playing by pressing the NightButton A on the remote. Next, press the K/Lbuttons C to select either the middle range orfull compression versions of the Night mode. Toturn the Night mode off, press the K/L buttonsC until the message in the lower third of thevideo display and the Main InformationDisplay F reads D-RANGE OFF.

The Night mode may also be selected to always beon at either level of compression as soon as theDolby Digital mode is turned on using the optionsin the Night Mode settings. See page 19 forinformation on using this option.

IMPORTANT NOTES ON DIGITAL PLAYBACK:1. When the digital playback source is stopped,or in a pause, fast forward or chapter searchmode, the digital audio data will momentarilystop, and the channel position letters inside theSpeaker/Channel Indicators 5 will flash.This is normal and does not indicate a problemwith either the AVR or the source machine. TheAVR will return to digital playback as soon as thedata is available and when the machine is in astandard play mode.

2. Although the AVR will decode virtually all DVDmovies, CDs and HDTV sources, it is possible thatsome future digital sources may not becompatible with the AVR.

3. Note that not all digitally encoded programsand not all audio tracks on a DVD contain full5.1-channel audio. Consult the program guidethat accompanies the DVD or laser disc todetermine which type of audio has beenrecorded on the disc. The AVR will automaticallysense the type of digital surround encoding usedand adjust to accommodate it.

4. When a Dolby Digital or DTS source is playing,you normally may not be able to select some ofthe analog surround modes such as Dolby ProLogic II, Dolby 3 Stereo, Hall, Theater, 5CH Stereoor Logic 7, except with special audio tracks (see indication ”Dolby Digital” on previous page)or data format selected (see ”PCM” on previouspage).

5. When a Dolby Digital or DTS source is playing,it is not possible to make an analog recordingusing the Tape � or Video 1 � recordoutputs, if the source is connected to any digitalinput of the AVR only. But the analog two

channel signal of that source, the ”Downmix” toStereo or Dolby Surround, can be recorded byconnecting its analog audio outputs to theappropriate analog inputs (e.g. DVD) of the AVR,even if the digital input of the AVR remainsselected. Additionally, the digital signals will bepassed through to the Digital Audio Outputs .

Tape Recording

In normal operation, the audio or video sourceselected for listening through the AVR is sent tothe record outputs. This means that any programyou are watching or listening to may be recordedsimply by placing machines connected to the out-puts for Tape Outputs � or Video 1 Outputs�� in the record mode.

Output Level Trim Adjustment

Normal output level adjustment for the AVR isestablished using the test tone, as outlined onpage 20. In some cases, however, it may bedesirable to adjust the output levels usingprogram material such as a test disc, or aselection you are familiar with. Additionally, theoutput level for the subwoofer can only beadjusted using this procedure.

To adjust the output levels using programmaterial, first select the surround mode for whichyou want to trim the speakers (see NOTE below)by selecting the appropriate input, associatedwith the desired surround mode, start yourprogram material source and set the referencevolume for the front left and front right channelsusing the Volume Control I�.

Once the reference level has been set, press theChannel Select button C and note thatFRONT L LEVEL will appear in the MainInformation Display F for five seconds. Tochange the level, first press the Set button E,and then use the K/L buttons C to raise orlower the level. DO NOT use the volume control,as this will alter the reference setting.

Once the change has been made, press the Setbutton E and then press the K/L buttonsC to select the next output channel locationthat you wish to adjust. To adjust the subwooferlevel, press the K/Lbuttons C untilWOOFER LEVEL appears in the MainInformation Display F (only available if thesubwoofer was selected during the speakerconfiguration, see page 16).

Operation

ENG

LISH

OPERATION 27

Operation

Press the Set button E when the name of thedesired channel appears in the MainInformation Display F and on-screen display,and follow the instructions shown above toadjust the level.

Repeat the procedure as needed until allchannels requiring adjustment have been set.When all adjustments have been made press theSet button E twice, the AVR will return tonormal operation.

NOTE: The output levels may be separatelytrimmed for each digital and analog surround mode.If you wish to have different trim levels for a specificmode, select that mode and then follow theinstructions in the steps shown above.

Changing the levels by the trim adjustment asdescribed above will automatically change thelevel settings shown during the Output LevelAdjustment (see page 19) correspondingly (andvice versa) and will remain in the AVR´s memorysystem, even when the unit is turned off. WithStereo modes the adjustment proceduredescribed above is the only way to trim the out-put level.

6-Channel Direct Input

The AVR is equipped for future expansionthrough the use of optional, external adapters forformats that the AVR may not be capable ofprocessing. When an adapter is connected to the6-Channel Direct Input �, you may select itby pressing the 6-Ch Direct Input Selector�. The 6-Channel Direct Input may also beselected by pressing the Input Source Selectorbutton A on the front panel until the words 6 CH DIRECT appear in the MainInformation Display F, and a blue LED lightsnext to 6 CH in the Input Indicators J.

Note that when the 6-Channel Direct Input is inuse, you may not select a surround mode, as theexternal decoder determines processing. Inaddition, there is no signal at the record outputswhen the 6-Channel Direct Input is in use.

Display Brightness

The AVR’s front panel Main InformationDisplay F is set at a default brightness levelthat is sufficient for viewing in a normally litroom. However, in some home theaterinstallations, you may wish to occasionally lowerthe brightness of the display, or turn it offcompletely.

You can also adjust the Display Brightness bypressing the Dim Button on the remotecontrol. Note that the blue lighting inside thevolume control and the Power Indicator 2will remain lit at normal brightness to remind youthat the unit is still turned on.

Memory Backup

This product is equipped with a memory backupsystem that preserves tuner presets and systemconfiguration information if the unit is turned offcompletely, accidentally unplugged or subjectedto a power outage. This memory will last forapproximately 1 week, after which time all information must be reentered.

Tuner Operation

The AVR’s tuner is capable of tuning AM, FM andFM Stereo broadcast stations and receiving RDSdata. Stations may be tuned manually, or theymay be stored as favorite station presets andrecalled from a 30 position memory.

Station Selection

1. Press the AM/FM Tuner Select button 6on the remote to select the tuner as an input. Thetuner may be selected from the front panel byeither pressing the Input Source Selector Auntil the tuner is active or by pressing the TunerBand Selector 8 at any time.

2. Press the AM/FM Tuner Select button 6 orTuner Band Selector 8 again to switchbetween AM and FM so that the desiredfrequency band is selected.

3. Press the Tuner Mode button H on theremote or hold the Band Selector 8 on thefront panel pressed for 3 seconds to select manualor automatic tuning.

When the button is pressed so that AUTOappears in the Main Information Display Feach press of the Tuning Selectors 7J willput the tuner in a scan mode that seeks the nexthigher or lower frequency station with acceptablesignal strength. An AUTO ST TUNEDindication will momentarily appear when thestation stops at a stereo FM station, and anAUTO TUNED indication will momentarilyappear when an AM or monaural FM station istuned. Press the Tuning buttons again to scan tothe next receivable station.

When the button is pressed so that MANUALappears in the Main Information Display Feach tap of the Selector will increased ordecrease the frequency by one increment. Whenthe tuner receives a strong enough signal foradequate reception, MANAUL TUNED willappear in the Main Information Display F.

4. Stations may also be tuned directly by pressingthe Direct button I, and then pressing theNumeric Keys G that correspond to thestation’s frequency. The desired station willautomatically be tuned after the latest number isentered. If you press an incorrect button whileentering a direct frequency, press the Clearbutton � to start over.

NOTE: When the FM reception of a stereo stationis weak, audio quality will be increased byswitching to Mono mode by pressing the TunerMode button H on the remote or holding theBand Selector 8 on the front panel so thatMANUAL appears momentarily in the MainInformation Display F and then goes out.

Preset TuningUsing the remote, up to 30 stations may bestored in the AVR’s memory for easy recall usingthe front panel controls or the remote.

To enter a station into the memory, first tune thestation using the steps outlined above. Then:

1. Press the Memory button Q on the remote.Note that two underscore lines will appear in theMain Information Display F.

2. Within five seconds, press the Numeric KeysG corresponding to the location where youwish to store this station’s frequency. Onceentered, the preset number will appear in theMain Information Display F.

3. Repeat the process after tuning any additionalstations to be preset.

Recalling Preset Stations• To manually select a station previously enteredin the preset memory, press the Numeric KeysG that correspond to the desired station’smemory location.

• To manually tune through the list of storedpreset stations one by one, press the PresetStations Selector buttons 9O on the frontpanel or remote.

28 OPERATION

Operation

RDS Operation

The AVR is equipped with RDS (Radio DataSystem), which brings a wide range ofinformation to FM radio. Now in use in manycountries, RDS is a system for transmitting stationcall signs or network information, a descriptionof station program type, text messages about thestation or specifics of a musical selection, andthe correct time.

As more FM stations become equipped with RDScapabilities, the AVR will serve as an easy-to-usecenter for both information and entertainment.This section will help you take maximumadvantage of the RDS system.

RDS TuningWhen an FM station is tuned in and it containsRDS data, the AVR will automatically display thestation’s call sign or other program service in theMain Information Display F.

RDS Display OptionsThe RDS system is capable of transmitting awide variety of information in addition to theinitial station call sign that appears when astation is first tuned. In normal RDS operationthe display will indicate the station name,broadcast network or call letters. Pressing theRDS button BN enables you to cyclethrough the various data types in the followingsequence:

• The station’s call letters (with some privatestations other information too).

• The station’s frequency (FREQ).

• The Program Type (PTY) as shown in the listbelow.

• A “text” message (Radiotext,RT) containingspecial information from the broadcast station.Note that this message may scroll across thedisplay to permit messages longer than the eightpositions in the display. Depending on signalquality, it may take up to 30 seconds for the textmessage to appear; in that time, the wordTEXT will flash in the Information Display whenRT is selected.

• The current time of day (CT). Note that it maytake up to two minutes for the time to appear, inthat time the word TIME will flash in theinformation display when CT is selected. Pleasenote that the accuracy of the time data isdependent on the radio station, not the AVR.

Some RDS stations may not include some ofthese additional features. If the data required forthe selected mode is not being transmitted, theMain Information Display F will show aNO TYPE, NO TEXT or NO TIMEmessage after the individual time out.

In any FM mode the RDS function requires astrong enough signal for proper operation.

Program Search (PTY)An important feature of RDS is its capability ofencoding broadcasts with Program Type (PTY)codes that indicate the type of material beingbroadcast. The following list shows theabbreviations used to indicate each PTY, alongwith an explanation of the PTY:

• (RDS ONLY)

• (TRAFFIC)

• NEWS: News

• AFFAIRS: Current Affairs

• INFO: Infomation

• SPORT: Sports

• EDUCATE: Educational

• DRAMA: Drama

• CULTURE: Culture

• SCIENCE: Science

• VARIED: Varied Speech Programs

• POPM: Popular Music

• ROCKM: Rock Music

• M.O.R.M.: Middle-of-the-Road Music

• LIGHTM: Classical Music

• CLASSICS: Serious Classical Music

• OTHERM: Other Music

• WEATHER: Weather Information

• FINANCE: Financial Programs

• CHILDREN: Children’s Programs

• SOCIAL A: Social Affairs Programs

• RELIGION: Religious Broadcasts

• PHONE IN: Phone-In Programs

• TRAVEL: Travel and Touring

• LEISURE: Leisure and Hobby

• JAZZ: Jazz Music

• COUNTRY: Country Music

• NATIONAL: National Music

• OLDIES: Oldies Music

• FOLK M: Folk Music

• DOCUMENT: Documentary Programs

• TEST: Emergency Test

• ALARM: Emergency Broadcast Information

You may search for a specific Program Type (PTY)by following these steps:

1. Press the RDS button BN until thecurrent PTY is shown in the Main InformationDisplay F.

2. While the PTY is shown, press the PresetUp/Down button 9O or hold them pressedto scroll through the list of available PTY types,as shown above. To simply search for the nextstation transmitting any RDS data, use thePreset Up/Down button 9O until RDSONLY appears in the display.

3. Press any of the Tuning Up/Down buttons7J, the tuner begins to scan the FM bandupwards or downwards for the first station thathas RDS data that matches the desiredselection, and acceptable signal strength forquality reception.

4. The tuner will make up to one complete scanof the entire FM band for the next station thatmatches the desired PTY type and hasacceptable reception quality. If no such station isfound, the display will read NONE for someseconds and the tuner will return to the last FMstation in use before the search.

NOTE: Many stations do not transmit a specificPTY. The display will show NONE, when such astation is selected and PTY is active.

NOTE: Some stations transmit constant trafficinformation. These stations can be found byselecting TRAFFIC, the option in front of NEWS inthe list. The AVR will find the appropriate station,even if it is not broadcasting traffic informationwhen the search is made.

ENG

LISH

OPERATION 29

Programming the Remote

The AVR is equipped with a powerful remotecontrol that will control not only the receiver’sfunctions, but also most popular brands of audioand video equipment, including CD players, TVsets, cable boxes, VCRs, satellite receivers andother home-theater equipment. Once the AVR’sremote is programmed with the codes for theproducts you own, it is possible to eliminate mostother remotes and replace them with theconvenience of a single universal remote control.

Programming the Remote with Codes

As shipped from the factory, the remote is fullyprogrammed for all AVR functions, as well as thoseof most Harman Kardon CD recorders, DVDplayers, CD players and cassette decks. In addition,by following one of the methods below, you mayprogram the remote to operate a wide range ofdevices from other manufacturers.

Note: The Input Selector button Video 3 4cannot be programmed with codes as it functionsas input selector for the AVR only. Moreover, onlythe default code "001" can be programmed onthe AVR Selector button 5.

Direct Code Entry This method is the easiest way to program yourremote to work with different products.

1. Use the tables in the separate booklet todetermine the three-digit code or codes thatmatch both the product type (e.g., VCR, TV), andthe specific brand name. If there is more than onenumber for a brand, make note of the differentchoices.

2. Turn on the unit you wish to program into theAVR remote.

3. Press and hold both the Input Selector 4for the type of product to be entered (e.g., VCR,TV) and the Mute button � at the sametime. When the Program Indicator 2 turnsorange and begins flashing, release the buttons.It is important that you begin the next step within20 seconds.

4. If the unit you wish to program into the AVRremote has a remotable Power on/off function,follow these steps:

a. Point the AVR’s remote towards the unit to beprogrammed, and enter the first three-digit codenumber using the Numeric buttons G. If theunit being programmed turns off, the correctcode has been entered. Press the InputSelector 4 again, and note that the red lightunder the Input Selector will flash three timesbefore going dark to confirm the entry.

b. If the product to be programmed does NOTturn off, continue to enter the three-digit codenumbers until the equipment turns off. At thispoint, the correct code has been entered. Pressthe Input Selector 4 again and note thatthe red light under the Input Selector willflash three times before going dark to confirmthe entry.

5. If the Power function of the unit to be pro-grammed cannot be remoted, follow these steps(max. 20 seconds after step 3 above, or else step3 must be repeated first):

a. Enter the first three-digit code number usingthe Numeric buttons G and press the InputSelector 4 again. Press the remote buttonof any transport function remotable with theunit, e.g. Pause or Play N M. If the unitbeing programmed starts that function, thecorrect code has been entered.

b. If the unit does not start the function whosebutton was pressed, repeat steps 3 and 5aabove with the next three-digit code numberlisted in the setup code table for that brandand product type, until the unit reacts properlyon the transport function transmitted.

6. Try all of the functions on the remote to makecertain that the product operates properly. Keepin mind that many manufacturers use a numberof different combinations of codes, so it is a goodidea to make certain that not only does thePower control work, but that the volume, channeland transport controls work as they should. Iffunctions do not work properly, you may need touse a different remote code.

7. If the unit does not react to any codeentered, if the code for your product does notappear in the tables in the booklet, or if not allfunctions operate properly, try programming theremote with the Auto Search Method.

Note on Using the AVR remote with aHarman Kardon CD Recorder.As shipped from the factory the remote is pro-grammed for controlling Harman Kardon CDplayers. But it is able to control most functionsof the Harman Kardon CD Recorders (seefunction list on page 32) too after the code”002” is entered to the CD Selector button4 as described above. For returning to the CDplayer control commands the code ”001” mustbe entered.

Auto-Search MethodIf the unit you wish to include in the AVR’sremote is not listed in the code tables the bookletmanual or if the code does not seem to operateproperly, you may wish to program the correctcode using the Auto Search method that follows.Note that the Auto Search method works only

with units whose Power functions can beremoted:

1. Turn on the product that you wish to include inthe AVR remote.

2. Press and hold both the Input Selector 4for the type of product to be entered (e.g., VCR,TV) and the Mute button � at the sametime. When the Program Indicator 2 turnsorange and begins flashing, release the buttons.It is important that you begin the next step within20 seconds.

3. To find out if the code for your unit is pre-pro-grammed, point the AVR remote towards the unitto be programmed, and press and hold the K

buttonC. This will send out a series of codesfrom the remote’s built-in data base, with eachflash of the red light under the Input Selector4 indicating that a code has been sent. Whenthe device to be programmed turns off,immediate-ly release the K buttonC. Note that it maytake one minute or more until the right code isfound and the unit turns off.

4. When the K button was not released in timeafter the unit turned off, the proper code mayhave been ”overrun”. That’s why a function testshould be made: Turn the unit on again and,while the Input Selector 4 still lights red,press the K buttonC once, than the L but-ton C once too. When the unit turns off, theright code was found, when not, the code was”overrun”. To re-find the correct, while the InputSelector 4 still lights red, press (not holdpressed) the L button C repeatedly to stepbackwards through the codes available andobserve the reaction of the unit at each press.As soon as the unit turns off the correct code isfound.

5. Press the Input Selector 4 again, and notethat the red light will flash three times beforegoing dark to confirm the entry.

6. Try all of the functions on the remote to makecertain that the product operates. Keep in mindthat many manufacturers use a number ofdifferent combinations of codes, and it is a goodidea to make certain that not only the Powercontrol works, but the volume, channel andtransport controls, as appropriate. If all functionsdo not work properly, you may need to Auto-Search for a different code, or enter a code viathe Direct Code Entry method.

Code Readout

When the code has been entered using the AutoSearch method, it is always a good idea to findout the exact code so that it may be easilyreentered if necessary. You may also read thecodes to verify which device has been pro-grammed to a specific Control Selector button.

30 PROGRAMMING THE REMOTE


1. Press and hold both the Input Selector 4for the device you wish to find the code for andthe Mute button � at the same time. Notethat the Program/SPL Indicator 2 willinitally turn amber and begin flashing. Releasethe buttons and begin the next step within 20 seconds.

2. Press the Set button F. The ProgramIndicator 2 will then blink green in a sequencethat corresponds to the three-digit code, with aone-second pause between each digit. Count thenumber of blinks between each pause to determinethe digit of the code. One blink is the number 1,two blinks is the number 2, and so forth. Note thata rapid sequence of three blinks is used to indicatea “0.”

Example: One blink, followed by a one-secondpause, followed by six blinks, followed by a one-second pause, followed by four blinks indicatesthat the code has been set to 164.

For future reference enter the Setup Codes for theequipment in your system here:

DVD ____________ CD ________________

VID1/VCR ________ VID2/CBL/SAT ______

VID3/TV____________________________

VID4 ______________________________

TAPE ______________________________

Programmed Device Functions

Once the AVR’s remote has been programmed forthe codes of other devices, press the appropriateInput Selector 4 to change the remote fromcontrol over the AVR to the additional product.When you press any of these buttons, it will brieflyflash in red to indicate that you have changed thedevice being controlled.

When operating a device other than the AVR, thecontrols may not correspond exactly to thefunction printed on the remote or button. Somecommands, such as the volume control, are thesame as they are with the AVR. Other buttons willchange their function so that they correspond to asecondary label on the remote. For example, theSleep and Surround mode selector buttons alsofunction as the Channel Up and Channel Downbuttons when operating most TV sets, VCRs orSat-Receivers.

For some products, however, the function of aparticular button does not follow the commandprinted on the remote. In order to see whichfunction a button controls, consult the FunctionList tables printed on page 32. To use thosetables, first check the type of device being

controlled (e.g., TV, VCR). Next, look at theremote control diagram on page 32. Note thateach button has a number on it.

To find out what function a particular button hasfor a specific device, find the button number onthe Function List and then look in the column forthe device you are controlling. For example,button number 51 is the Macro 2 button for the AVR, but it is the “Favorite” button for manycable television boxes and satellite receivers.Button number 30 is the Delay button for theAVR, but the Open/Close button for CD players.

Note that the numbers used to describe thebutton functions at the left for the purposes ofdescribing how a button operates are a differentset of numbers than those used in the rest of thismanual to describe the button functions for theAVR.

Notes on Using the AVR Remote With Other Devices.• Manufacturers may use different code sets forthe same product category. For that reason, it isimportant that you check to see if the code setyou have entered operates as many controls aspossible. If it appears that only a few functionsoperate, check to see if another code set willwork with more buttons.

• Depending on the brand and product type usedthe functions listed in the Function List tablesmay not correspond with the function the unitreacts on the command. In these cases it’s agood idea to edit the reaction of the unit into thecorresponding line of the table or to set up aseparate list.

• When a button is pressed on the AVR remote,the red light under the Input Selector 4 forthe product being operated should flash briefly. Ifthe Device Control Selector flashes for some butnot all buttons for a particular product, it doesNOT indicate a problem with the remote, butrather that no function is programmed for thebutton being pushed.

• The remote was pre-programmed with codesfor units of the latest generation, but some codesmay differ from those needed for earlier units.

Macro Programming

Macros enable you to easily repeat frequentlyused combinations of commands with the press ofa single button on the AVR’s remote control. Onceprogrammed, a macro will send out up to 19different remote codes in a pre-determinedsequential order enabling you to automate theprocess of turning on your system, changingdevices, or other common tasks. The AVR’s remotecan store up to five separate macro commandsequences, one that is associated with the PowerOn button 0, and four more that are accessedby pressing the Macro buttons K.

1. Press the Mute button � and the Macrobutton K to be programmed or the Power-Onbutton 0 at the same time. Note that the latestselected Input Selector will light red, and theProgram Indicator 2 will flash orange.

2. Enter the steps for the macro sequence bypressing the button for the actual command step.Although the macro may contain up to 19 steps,each button press, including those used tochange devices, counts as a step. The ProgramIndicator 2 will flash green to confirm eachbutton press as you enter commands.

NOTE: While entering commands for Power On ofany device during a macro sequence, press theMute button �. DO NOT press the actual PowerON button.

• Remember to press the appropriate InputSelector button 4 before functions arechanged to another device. This is also needed forthe AVR Selector button 5 itself, as long asit’s not lit red and AVR functions shall beprogrammed.

3. When all the steps have been entered, pressthe Sleep button 8 to enter the commands.The red light under the Input Selector 45will blink and then turn off.

Example: To program the Macro 1 K buttonso that it turns on the AVR, TV follow these steps:• Press the Macro 1 button K and Mute �buttons at the same time and then release them.• Note that the Program Indicator will flashorange.• Press the AVR Selector 5.• Press the Mute � button to store the AVR’spower on command.• Press the VID 2 Input Selector button 4 toindicate the next command is for “TV Power On.”• Press the Mute � button to store the TVPower On Command.• Press the Sleep/Channel Up button 8 tocomplete the process and store the macrosequence.

After following these steps, each time you pressthe Macro 1 button K, the remote will sendall Power On commands.

Erasing Macro CommandsTo remove the commands that have beenprogrammed into one of the Macro buttons,follow these steps:

1. Press the Mute button � and the Macrobutton K that contains the commands youwish to erase.

2. Note that the Program Indicator 2 willflash orange, and the LED under the AVRSelector 5 will turn red.

3. Within ten seconds, press the SurroundMode Selector/Channel Down button 9.

ENG

LISH

PROGRAMMING THE REMOTE 31


4. The red LED under the AVR Selector will goout, and the Program Indicator 2 will turngreen and flash three times before it goes out.

5. When the Program Indicator 2 goes out,the Macro has been erased.

Volume Punch-Through

The AVR’s remote may be programmed to operatethe Volume Control � and the Mute �from either the TV or the AVR in conjunction withany of the six devices controlled by the remote.For example, since the AVR will likely be used asthe sound system for TV viewing, you may wish tohave the AVR’s volume activated although theremote is set to run the TV.

To program the remote for Volume Punch-Through, follow these steps:

1. Press the Input Selector 4 for the unit youwish to have associated with the volume controland the Mute button � at the same time untilthe red light illuminates under the Input Selector4 and note that the Program Indicator 2will flash orange.

2. Press the Volume Up button � and notethat the Program Indicator 2 will stopflashing and stay orange.

3. Press either the AVR Selector 5 or theInput Selector 4, depending on which sys-tem’s volume control you wish to have attachedfor the punch-through mode. The ProgramIndicator 2 will blink green three times andthen go out to confirm the data entry.

Example: To have the AVR’s volume controlactivated even though the remote is set tocontrol the TV, first press the Video/TV InputSelector 4 and the Mute button � at thesame time. Next, press the Volume Up button�, followed by the AVR Input Selector 5.

NOTE: Should you wish to return the remote tothe original configuration after entering a VolumePunch-Through, you will need to repeat the stepsshown above. However, in the example above,press the Video/TV Input Selector in steps oneand three.

Channel Control Punch-Through

The AVR’s remote may be programmed to operateso that the channel control function for either theVCR, TV, cable or satellite receiver used in yoursystem may be used in conjunction with one ofthe other devices controlled by the remote. Forexample, while using and controlling the VCR,you may wish to change channels on a cable boxor satellite receiver without having to change thedevice selected by the AVR or the remote. Toprogram the remote for Channel Control Punch-Through, follow these steps:

1. Press the Input Selector button 4 for thedevice you wish to have the channel controlassociated with and the Mute button � at thesame time until the red light illuminates under theInput Selector 4 and the ProgramIndicator 2 flashes orange.

2. Press the Volume Down button �. TheProgram Indicator 2 will stop flashing andstay orange.

3. Press and release the AVR 5 or InputSelector button 4 for the device that will beused to change the channels. The ProgramIndicator 2 will blink green three times andthen go out to confirm the data entry.

Example: To control the channels using your TVwhile the remote is set to control the VCR, firstpress the VID 1/VCR Input Selector button 4and the Mute button � at the same time. Next,release them and press the Volume Down button�, followed by the VID 2/TV Input Selectorbutton 4.

NOTE: To remove the Channel Control Punch-Through and return the remote to its originalconfiguration, repeat the steps shown in theexample above. However, press the VID 1/VCRInput Selector in Steps 1 and 3.

Transport Control Punch-Through

The AVR’s remote may be programmed to operateso that the Transport Control Functions L (Play,Stop, Fast Forward, Rewind, Pause and Record) fora VCR, DVD or CD will operate in conjunction withone of the other devices controlled by the remote.For example, while using and controlling the TV,you may wish to start or stop your VCR or DVDwithout having to change the device selected bythe AVR or the remote. To program the remote forTransport Control Punch-Through, follow thesesteps:

1. Press the Input Selector 4 for the deviceyou wish to have the transport control associatedwith and the Mute button � at the same timeuntil the red light illuminates, under the InputSelector 4 and the Program Indicator 2flashes orange.

2. Press the Play button L. The ProgramIndicator 2 will stop flashing and stay orange.

3. Press and release the AVR 5 or InputSelector button 4 for the device that will beused to change the transport function. TheProgram Indicator 2 will blink green threetimes and then go out to confirm the data entry.

Example: To control the transport of a CD playerwhile the remote is set to control the TV, press theVID 2/TV Input Selector button 4and theMute button � at the same time. Next, releasethem and press the Play button L, followed bythe CD Input Selector button 4.

NOTE: To remove the Transport Control Punch-Through and return the remote to its originalconfiguration, repeat the steps shown in theexample above. However, press the VID 2/TVInput Selector in Steps 1 and 3.

NOTE: Before programming the remote forVolume, Channel or Transport Punch-Through,make certain that any programming needed forthe specific TV, CD, DVD, Cable or SatelliteReceivers has been completed.

Resetting the Remote Memory

As you add components to your home-theatersystem, occasionally you may wish to totallyreprogram the remote control without theconfusion of any commands, macros or ”Punch-Through“ programming that you may have done.To do this, it is possible to reset the remote to theoriginal factory defaults and command codes byfollowing these steps. Note, however, that once theremote is reset, all commands or codes that youhave entered will be erased and will need to bereentered:

1. Press any of the Input Selector buttons 4and the ”O“ button G at the same time untilthe Program Indicator 2 begins to flashorange.

2. Press the ”3“ button G three times.

3. The red LED under the Input Selector 4 willgo out and the Program Indicator 2 will stopflashing and turn green.

4. The Program Indicator 2 will remain greenuntil the remote is reset. Note that this may take awhile, depending on how many commands are inthe memory and need to be erased.

5. When the Program Indicator 2 goes out,the remote has been reset to the factory settings.

32 FUNCTION LIST

Function List

686766

656463

6261

605958

575655

54535251

504948

137

No. Button Name AVR Function DVD CD/CDR

1 Power On Power On Power On Power On2 Power Off Power Off Power Off Power Off3 Mute Mute4 AVR AVR Select5 DVD DVD Input Select DVD Select6 CD CD Input Select CD Select7 Tape Tape Input Select8 VID 1 Video 1 Select9 VID 2 Video 2 Select

10 VID 3 Video 3 Select11 DIM DIM12 AM/FM Tuner Select13 6 CH Input Select 6 CH Input Selector14 Sleep Sleep15 Test Test Tone -/Input Select16 TV TV/DVD -/CDP Select17 Volume Up Volume Up Volume Up18 Surround Select Surround Mode Select -/CDR Select19 Night Night Mode Select Subtitle on/off20 Spare21 Volume Down Volume Down Volume Down22 Channel/Guide Channel Trim Title23 K Move/Adjust Up Up24 Speaker/Menu Speaker Adjust Menu Intro/-25 A Left26 Set Set Enter27 B Right28 Digital/Exit Digital Input Select Open/Close29 L Move/Adjust Down Down30 Delay/Prev. Ch. Delay Adjust Return Open/Close31 1 1 1 132 2 2 2 233 3 3 3 334 4 4 4 435 5 5 5 536 6 6 6 637 7 7 7 738 8 8 8 839 Tun-M Tuner Mode Chapter Repeat40 9 9 9 941 0 0 0 042 Memory Memory Audio Time/CDR Display43 Tune Up Tune Up44 Direct Direct Tuner Entry Angle Random45 Clear Clear Clear Clear46 Preset Up Preset Tune Up Slow Forward +10/-47 Tune Down Tune Down -/Track Increment48 Tone Mode49 RDS RDS Select Disc Skip Disc Skip50 Preset Down Preset Tune Down Slow Rev51 M152 M253 M354 M455 Dolby Dolby Mode Select56 DTS Sur DTS 5.1 Select57 DTS Neo:6 DTS Neo:6 Select58 Night Night Mode Select59 Logic 7 Logic 7 Select60 Stereo Stereo Select 61 Skip Down Skip – Skip –62 Skip Up Skip + Skip +63 Rewind R. Search R. Search64 Play Play Play65 Fast Forward F. Search F. Search66 Record -/Record67 Stop Stop Stop68 Pause Pause Pause

ENG

LISH

FUNCTION LIST 33

Function List

No. Button Name Tape VCR (VID 1) TV (VID 2) CBL (VID 3) SAT (VID 3)

1 Power On Power On Power On Power On Power On Power On2 Power Off Power Off Power Off Power Off Power Off Power Off3 Mute Mute4 AVR5 DVD6 CD7 Tape Tape Select8 VID 1 VCR Select9 VID 2 TV Select CBL/SAT Select

10 VID 3 Video 3 Select11 DIM12 AM/FM 12 6 CH Input Select14 Sleep Channel + Channel + Channel + Channel +15 Test 16 TV TV/VCR TV/VCR TV/Cable TV/Sat17 Volume Up Volume Up Volume Up18 Surround Select Channel – Channel – Channel – 19 Night20 Spare21 Volume Down Volume Down22 Channel/Guide Info/Guide Info/Guide23 K Up Up Up Up24 Speaker/Menu Menu Menu Menu Menu25 A Left Left Left Left26 Set Enter Enter Enter Enter27 B Right Right Right Right28 Digital/Exit Exit Exit Exit Exit29 L Down Down Down Down30 Delay/Prev. Ch. Prev Channel Prev Channel Prev Channel31 1 1 1 1 132 2 2 2 2 233 3 3 3 3 334 4 4 4 4 435 5 5 5 5 536 6 6 6 6 637 7 7 7 7 738 8 8 8 8 839 Tun-M40 9 9 9 9 941 0 0 0 0 042 Memory43 Tune Up44 Direct45 Clear Clear Clear Clear Clear46 Preset Up47 Tune Down48 Tone Mode49 RDS50 Preset Down51 M1 Cancel Sleep PPV Cancel52 M2 Fav Fav53 M3 Bypass Next54 M4 Music Alt55 Dolby Music Alt56 DTS Sur Music Alt57 DTS Neo:6 Music Alt58 Night59 Logic 7 Music Alt60 Stereo Music Alt61 Skip Down Scan – Page – Page –62 Skip Up Scan + Page + Page +63 Rewind Rewind Rewind Day – Say –64 Play Play Play65 Fast Forward Fast Fwd Fast Fwd Day + Day +66 Record Record/Rec.Pause Record67 Stop Stop Stop68 Pause Pause

34 TROUBLESHOOTING GUIDE

Troubleshooting Guide

Processor Reset

In the rare case where the unit’s operation or thedisplays seem abnormal, the cause may involvethe erratic operation of the system’s memory ormicroprocessor.

To correct this problem, first unplug the unit fromthe AC wall outlet and wait at least threeminutes. After the pause, reconnect the ACpower cord and check the unit’s operation. If thesystem still malfunctions, a system reset mayclear the problem.

To clear the AVR’s entire system memoryincluding tuner presets, output level settings,delay times and speaker configuration data, firstput the unit in Standby by pressing the SystemPower Control button 1. Next, press and holdthe Surround Mode Button 6 for 5 seconds.

The unit will turn on automatically. Note thatonce you have cleared the memory in this manner,it is necessary to re-establish all systemconfiguration settings and tuner presets.

NOTE: Resetting the processor will erase anyconfiguration settings you have made forspeakers, output levels, surround modes, digitalinput assignments as well as the tuner presets.After a reset the unit will be returned to thefactory presets, and all settings for these itemsmust be reentered.

If the system is still operating incorrectly, theremay have been an electronic discharge or severeAC line interference that has corrupted thememory or microprocessor.

If these steps do not solve the problem, consultan authorized Harman Kardon service depot.

SYMPTOM CAUSE SOLUTION

Unit does not function when • No AC Power • Make certain AC power cord is plugged Main Power Switch � is pushed into a live outlet

• Check to see if outlet is switch controlled

Display lights, but no sound • Intermittent input connections • Make certain that all input and speaker or picture connections are secure

• Mute is on • Press Mute button �• Volume control is down • Turn up volume control

Sound is heard, but Front-Panel • Display brightness is turned off • Follow the instructions in the Display Brightness section Display does not light on page 27 so that the display is set to VFD FULL

No sound from any speaker; • Amplifier is in protection mode • Check speaker-wire connections for shorts at receiver light around Power switch 1 is red due to possible short and speaker ends

• Amplifier is in protection mode • Contact your local Harman Kardon service depotdue to internal problems

No sound from surround or • Incorrect surround mode • Select a mode other than Stereocenter speakers • Incorrect configuration • Check speaker mode

• Stereo or Mono program material • With (analog or digital) Dolby surround modes, the surround decoder may not create rear-channel information from non-encoded programs

• Speakers not properly connected • Check speaker-wire connections or use test toneto verify connections (see page 20)

Unit does not respond to • Weak batteries in remote • Change remote batteriesremote commands • Wrong device selected • Press the AVR selector 5

• Remote sensor E is obscured • Make certain front-panel sensor is visible to remote or connect remote sensor

Intermittent buzzing in tuner • Local interference • Move unit or antenna away from computers, fluorescent lights,motors or other electrical appliances

Letters flash in the Channel Indicator • Digital audio feed paused • Resume play for DVDDisplay � and Digital Audio stops • Check that Digital Signal is fed to the Digital Input selected

ENG

LISH

TECHNICAL SPECIFICATIONS 35

Technical Specifications

Audio SectionStereo Mode Continuous Average Power (FTC)

40 Watts per channel, 20Hz–20kHz,@ < 0.07% THD, both channels driven into 8 ohms

Five-Channel Surround Modes Power Per Individual Channel

Front L&R channels:30 Watts per channel,@ < 0.07% THD, 20Hz–20kHz into 8 ohms

Center channel:30 Watts, @ < 0.07% THD, 20Hz–20kHz into 8 ohms

Surround channels:30 Watts per channel,@ < 0.07% THD, 20Hz–20kHz into 8 ohms

Input Sensitivity/Impedance Linear (High Level) 200mV/47kohms

Signal-to-Noise Ratio (IHF-A) 95dB

Surround System Adjacent Channel Separation Analog Decoding 40dB (Pro Logic, etc.) Dolby Digital (AC-3) 55dB DTS 55dB

Frequency Response @ 1W (+0dB, –3dB) 10Hz–100kHz

High Instantaneous Current Capability (HCC) ±25 Amps

Transient Intermodulation Distortion (TIM) Unmeasurable

Rise Time 16 µsec

Slew Rate 40V/µsec

FM Tuner SectionFrequency Range 87.5–108MHzUsable Sensitivity IHF 1.3 µV/13.2dBfSignal-to-Noise Ratio Mono/Stereo: 70/65dB (DIN)Distortion Mono/Stereo: 0.15/0.3%Stereo Separation 35dB @ 1kHzSelectivity ±400kHz: 70dBImage Rejection 80dBIF Rejection 90dB

AM Tuner SectionFrequency Range 522–1620kHzSignal-to-Noise Ratio 45dBUsable Sensitivity Loop: 500µVDistortion 1kHz, 50% Mod: 0.8%Selectivity ±10kHz: 30dB

Video SectionVideo Format PAL/NTSCInput Level/Impedance 1Vp-p/75 ohmsOutput Level/Impedance 1Vp-p/75 ohmsVideo Frequency Response 10Hz–8MHz (–3dB)

GeneralPower Requirement AC 220-240V/50HzPower Consumption 72W idle, 580W maximum

(2 channels driven)

Dimensions (Max)Width 440mm Height 165mm Depth 382mmWeight 9.6 kg

Depth measurement includes knobs, buttons and terminal connections.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.

Harman Kardon is a registered trademark.

*Manufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic”, and the Double-D symbol are trademarks of Dolby Laboratories, Inc.Confidential Unpublished Works. ©1992–1999 Dolby Laboratories, Inc.All rights reserved.

†"DTS" and "DTS Neo:6" are registered trademarks of DTS, Inc. "96/24" is a trademark of DTS, Inc.

Logic 7 is a registered trademark of Lexicon, Inc.

250 Crossways Park Drive, Woodbury, New York 11797www.harmankardon.comHarman Consumer Group, Inc.:2, route de Tours, 72500 Château-du-Loir, France© 2007 Harman Kardon, Incorporated Part No.: CQX1A1260Z

Documents

Owner-'s Manual - AVR 137 (English)