Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
NEUSPEED® • 3300 Corte Malpaso • Cam ar illo, CA 93012 • 805.388.7171 • 805.388.0030 FAX • inform [email protected] • Visit us on the web…ht tp: / / www.neuspeed.com
P - FL O A I R I N T A K E K I T – P A RT # 6 5 . 1 0 . 8 3Fi t s : 2 0 1 0 - 1 4 AUDI A3 2 .0 L TDI , 2 0 0 9 - 1 4 VW Jet t a V 2 .0 L TDI , 2 0 1 0 - 1 4 VW Jet t a VI 2 .0 L TDI Sed an & Sp or t w ag en an d 2 0 1 0 - 1 4 Go l f VI 2 .0 L TDI w it h 5 - Pin MAF
PARTS LI ST: TOOLS REQUI RED:
1 – I NTAKE PI PE 1 – STAI NLESS STEEEL P-FLO BRACKET 2 – M6 LOCK NUTS 1 – 90° SI LI CONE HOSE 1 – PHI LI PS SCREWDRI VER 1 – 5m m HEX KEY WRENCH 1 – 8m m NUT DRI VER
2 – # 48 HOSE CLAMP 1 – NEUSPEED FI LTER 1 – RUBBER I SOLATOR 1 – RUBBER GROMMET 1 – 7/ 16 OR 11MM WRENCH 1 – SPRI NG CLAMP PLI ERS 1 – T25 TORX
1 – ACORN NUT 2 – M6 x 16m m CAP BOLTS 1 – WIRE HARNESS 1 – 10 MM WRENCH 1 – 4MM HEX KEY WRENCH
1. Disconnect Mass Air Flow (MAF) sensor
electr ical connector.
2. Disconnect vacuum hose from air filter
box lid.
3. Disconnect air intake hose from MAF
using spring clam p pliers.
4. Unscrew all Philips screws around air
filter box lid and rem ove.
5. Disconnect hot air duct from back side
of air filer box.
6. Rem ove cover at intake duct.
7. Using a 5m m hex key wrench, unbolt
lower air filter box , located on back side.
8. Lif t off lower air f ilter box from rubber
grom m et m ounts, then lift out lef t side
f irst and rotate intake duct around sm all
coolant hose to remove.
9. Rem ove air intake duct at radiator
suppor t (2) T25 Torx, one on each side.
10. Remove hot air duct ing hose.
11. Remove MAF sensor from air box lid
using a Philips screwdriver.
12. I nstall and t ighten rubber isolator into
threaded stand-off j ust in front of
battery .
NEUSPEED® • 3300 Corte Malpaso • Cam ar illo, CA 93012 • 805.388.7171 • 805.388.0030 FAX • inform [email protected] • Visit us on the web…ht tp: / / www.neuspeed.com
13. Mount MAF sensor to SS P-Flo bracket
using supplied M6x16m m screws and
lock nuts, then t ighten.
14. I nstall NEUSPEED P-Flo bracket onto
rubber grom m et m ount and rubber
isolator .
15. I nstall and t ighten acorn nut using an
11m m wrench.
16. I nstall intake pipe with port closer to the
front and posit ioned at 1 o’clock.
17. I nstall 90° silicone hose onto MAF.
NOTE: Use silicone spray to ease install.
Slide the two supplied # 48 hose clam ps
onto silicone hose and then connect to
intake pipe. Now posit ion clam ps and
t ighten.
18. Connect vacuum line to por t on
NEUSPEED intake pipe.
19. Connect supplied MAF harness
extension.
20. Move MAF wire harness support clip
down next to vacuum canister.
21. I nstall rubber st r ip on top-edge of P-Flo
bracket .
22. For ext ra protect ion, slide coolant hose
protector sleeve just under P-Flo
bracket .
23. At tach and t ighten NEUSPEED filter .
Posit ion NEUSPEED logo on end of filter
hor izontally.
24. Double-check com plete installat ion.
Copyr ight 2013, NEUSPEED®
All r ights reserved. Reproduct ion in whole orin part prohibited.
DOC. 65.10.83 Rev. 07.25.12