Page 113 Thru 167

B29

Double Skin

(woven felt)

11.0-12.0mm

16.0-20.0mm

2.3mm/.090”

2.5mm/.098”

B32

B33

B33 Oval

Tan Kid

White Kid

White Kid

7.0-35.5mm

7.0-35.5mm

12mm X 14.5mm

3.2mm/.126”

3.2mm/.126”

3.2mm/.126”

B7 Double White

Skin

(needle felt)

11-12,

16-20mm

2.6mm/.101”

2.5mm/.098”

B8 Double Yellow

Skin

(needle felt)

11-12,

16-20mm

2.6mm/.101”

2.5mm/.098”

B30 Double Skin

(woven felt)

11-12.5,13,14

15, 16.0-

20.0mm

2.6mm/.101”

2.9mm/.114”

~Flute Pads-Old “Gemeinhardt” style~

B35, B37

B28

Double Skin

Yellow Dbl

Skin

6.5-15.5mm

6.5-15.5mm

2.3mm/.090”

2.3mm/.090”

PAD SPECIFICATIONS

Cat # Style Size Thickness

A54 Natural Cork 6.0-7.5mm

8.0-15.0mm

2.54mm/.100”

2.79mm/.110”

B9

B9A

Norbeck

Synthetic

7.0-20.0mm

9.0-20.0mm

2.54mm/.100”

3.55mm/.140”

~Clarinet Pads~

~All Clarinet Pads below are of needle felt and

beveled style~

B10

B11

Single Skin

Double Skin

6.5-8.5mm

9.0-13.5mm

14.0-20.0mm

2.9mm/.114”

3.6mm/.141”

3.9mm/.153”

B17

B20

B21

‘True’ Dbl Skin

Single Skin

Double Skin

6.5-8.5mm

9.0-13.5mm

14.0-20.0mm

2.6mm/.102”

2.99mm/.118”

3.5mm/.137”

B24

B25

Single Skin

Double Skin

6.5-8.5mm

9.0-13.5mm

14.0-20.0mm

2.3mm/.090”

2.48mm/.098”

2.8mm/.110”

~Oboe & Piccolo Pads~

A54 Natural Cork 6.0-7.5mm

8.0-15.0mm

2.54mm/.100”

2.79mm/.110”

B9

B9A

Norbeck

Synthetic

7.0-20.0mm

9.0-20.0mm

2.54mm/.100”

3.55mm/.140”

Norbeck’s DO NOT work on metal surfaces!

(octave vents, metal Piccolo body)

~All piccolo & Oboe pads below are of woven felt

and NOT beveled~

~Flute Pads-”Armstrong” style~

~Bassoon, Alto & Bass Clarinet~ ~These are ALL woven felt~

B31 Double white

Skin

(needle felt)

11.0-12.0mm

16.0-20.0mm

2.6mm/.101”

2.9mm/.114”

B38 Yellow Dbl

Skin, woven

felt

11.0-12.0mm

16.0-20.0mm

2.6mm/.101”

2.9mm/.114”

B26 ~De’Jur~

Yellow Dbl

Skin, needle

felt

11.0-12.0mm

16.0-20.0mm

2.6mm/.101”

2.9mm/.114”

See page 141 for cork pads. 113

Notes from customers: “It is nice to be, once again, be reminded of

a good thing. I well recognize all you wrote

and, having used the B53 pad, I KNOW that

the .025” difference is significant...i.e. the job

goes along much easier. Thanks,” Pat.

PA

D S

PE

CIF

ICA

TIO

NS

E33 CLARINET PAD SLICK

Used to level pads when regulating clarinets,

oboes, etc.. Has a small notch to aid in applying cork

or felt to the clarinets C key “crows foot.”

E33 Clarinet Pad Slick

LEBLANC/NOBLET ALTO &

BASS CLARINET GOLDBEATER

SKIN PADS—In SETS ONLY

B39LA LeBlanc/Noblet alto clarinet Set

B39LB LeBlanc/Noblet bass clarinet Set

Soprano Clarinet pads

B17 FERREE’S DE’JUR The oldest Name in Superior Pads

TOP OF THE LINE CLARINET PADS

These are the clarinet pads used by repairmen who

want to do an exceptionally unique job for the own-

er/player they are working for.

These De’jur clarinet pads are made from

premium selected true double skins and felt. The

pads have perfectly selected true double skins, two

separate skins. Sides are beveled and thickness is

medium just like the regular B21 style.

They can be recognized instantly by their peach

colored backs.

Note: When ordering pad sets please specify pad

cup sizes or pad sizes as supplied by you.

B17 De’jur medium, double skin

6.5 thru 20mm

B17B Clarinet Pad Set,

State specific sizes

B171 Assortment of 100 pads


B175C Assortment of 500 pads

with cabinet

B9 NORBECK PADS Manufactured by Ferree’s Tools, Inc.

Revolutionary, space-age technology.

Invented by Dr. Edwin Norbeck.

This pad is made of high-tech silicone originally

developed for use in nuclear physics research as a

gasketing material. It remains elastic and functional

at temperatures ranging from -130° F to +500° F.

Because of its resistance to deteriorating effects of

sunlight, moisture, ozone, radiation, oxidization and

temperature extremes, its service life is virtually un-

limited. The back of the pad is a composition cork so

that the pad may be mounted using conventional

methods. None of the conventional cements used in

normal pad installation will stick to the face of the

pad so any cement that accidentally gets onto the face

of the pad can easily be removed.

B9 Med. .100” , Sizes 7 thru 20mm

B9B Set of Med. pads for Clarinet

B9A Med. .140” thick, Sizes 13 thru 20mm

B9AB Set of Med. Thick pads for Clarinet



B95C Assortment of 500 pads with cabinet

HIGH QUALITY CLARINET PADS

▪High Grade bladder pads with glued backs

▪6.5mm thru 20mm in 1/2 mm steps

OEM B24 MEDIUM THIN, Single Skin

B24 Medium, single skin, 6.5 thru 20mm

B24B Clarinet Pad Set, state specific sizes




DELUXE B25 MEDIUM THIN, Double Skin

B25 Medium, double skin, 6.5 thru 20mm





OEM B20 MEDIUM, Single Skin






DELUXE B21 MEDIUM, Double Skin

Our most popular clarinet pads






OEM B10 MEDIUM THICK, Single Skin

(Thickness needed for Vito clarinets)






DELUXE B11 MEDIUM THICK, Double Skin






114

SO

P. C

LA

RIN

ET

PA

DS

DELUXE B35 OBOE PADS DOUBLE SKIN

B35 6.5mm thru 15.5mm in .5 steps

B35B Oboe Pad Set, state specific sizes


Other woodwind pads

HIGH QUALITY FLUTE PADS ALL DOUBLE SKIN

PREMIUM SELECT B7 NEEDLE FELT Firmer, less mushy, thickness .101” & .098”

B7 11, 11.5, 12, 16 thru 20mm——WHITE

B7B Flute Pad Set, state specific sizes


PREMIUM SELECT B8 NEEDLE FELT Firmer, less mushy, thickness .101” & .098”

B8 11, 11.5, 12, 16 thru 20mm——YELLOW



OEM STANDARD B29 WOVEN FELT Thin Thickness .090” & .098”

B29 11, 11.5, 12, 16 thru 20mm—-WHITE



OEM STANDARD B30 WOVEN FELT Standard Thickness .101” & .114”

B30 11, 11.5, 12, 16 thru 20mm—-WHITE



Additional sizes for Alto or Bass Flutes B30H 12.5, 13, 14, 15, 20.5 thru 40mm—-WHITE

B30HB Alto or Bass Flute Pad Set, state specific

sizes

OEM B38 WOVEN FELT Woven Felt-Thickness .101” & .114”

B38 11, 11.5, 12, 16 thru 20mm——YELLOW



DELUXE B31 NEEDLE FELT Firmer, less mushy, Thickness .101” & .114”

B31 11, 11.5, 12, 16 thru 20mm—-WHITE



DE’JUR SELECT B26 NEEDLE FELT Firmer, less mushy, thickness .101” & .114”

B26 11, 11.5, 12, 16 thru 20mm——YELLOW



SEE N79 FLUTE PAD PUNCH SET

TO MAKE FRENCH STYLE FLUTE PADS

OPEN TONE HOLE. PAGE 93

DELUXE B37 PICCOLO PADS Double skin—-White


B37B Piccolo Pad Set, state specific sizes


DELUXE B28 PICCOLO PADS, Double skin—Yellow


B28B Piccolo Pad Set, state specific sizes


ALTO, BASS CLARINET &

BASSOON PADS Made with woven felt

B32 TAN KID B32 7 thru 35.5mm in .5mm steps

B32A Soprano Clarinet Pad Set

B32B Alto Clarinet Pad Set

B32C Bass Clarinet Pad Set

B32D Bassoon Pad Set


NOTE: Newer alto and bass clarinets, such as Bun-

dy, can take plain or riveted sax pads, which are a

little thicker (approx. .035” OR .060”)

B33 WHITE KID B33 7 thru 35.5mm in .5mm steps

B33A Soprano Clarinet Pad Set

B33B Alto Clarinet Pad Set

B33C Bass Clarinet Pad Set

B33D Bassoon Pad Set


OVAL WHISPER KEY PADS A hard to find item for bassoons. White, leather,

oval shaped pads for whisper keys. These pads

measure 12.0mm X 14.5mm

B33 Oval whisper Key Pad (sold in dozens or hundreds—Must specify, oval

whisper key)

115

OT

HE

R W

/W P

AD

S

F27 Sax Key Bending Levers

B215C 500 Clarinet Pads

w/Cabinet

B311 (3) 100 Flute Pad

Assortments

B371 (2) 100 Piccolo Pad

Assortments

X14 Cabinet for Flute and

Oboe Pads

F98 3/32” Nut Driver

F99 1/8” Nut Driver

A55 1/64” Natural Sheet Cork





A63 Laminated Very Thin

Cork

D12A 4” Cork Gauge

J99 Hi-Heat Gun

G67B Amber Shellac

G19 Clear Magic Epoxy

H75 “Hot Stuff” Kit

H75C Spray

H75D Solvent

H75E Tubing

H70 Cork Cement

H70S Solvent

H72 Extra Can

R50 Testing Corks

F20 Knock Pin Tool

F66 Small Screwdriver

F67 Medium Screwdriver

F72 Large Screwdriver

F77-0 PowerDriver

F77-1/1L PowerDrivers

F77-2/2L PowerDrivers

F77-3/4/5 PowerDrivers

D6 Bench Peg-Traditional

D6A Reverse Peg

D6B Reverse Peg-large

D1A/D1B Medium/Large Sprghooks

D38 Spring Punches

D35 Testing Feeler Holder

J20SS/J22SS Rnd Nose/Sm. Duckbill Pliers

F75 Sax Bumper Adjuster

E2A Large Swedging Plier

E15A/B/C/D Swedging Pliers

E1 Hook Nose Key Bending Plier

E3/E4/E5 Spring Pliers

N78 Flute Cup Tool

E41 Flat Spring Tool

D14 Neck Screw Extractor

Q65-1 Leak Light Kit

J90 thru J94 Assembly Boards

G23 Bench Oiler

O38 Octave Tubing

E36 Flute Pad Pliers

E61 Flute Leveling Gauge

F12 Cork Stripper

G82 (18) Flute Clips

G26 (6) Flute Clips

G38A Wood Wedges

D13 Sax Pad Height Gauge

G21 Sax Key Leveling Tools

N99A Bench Motor

D5 Adaptor Chuck

D57 Grinding Wheel

N130 Sanding Rod Set

E40 Triangular Scraper

D42 Tenon Scraper

L24 Lead Block

E34 Flute Pad Iron

N79 Flute Pad Punch

P28 Cutting Pad

D2 Cork Knife

D33 Bench Knife

D45 Utility Knife

D101 1-60 Drill Set

D118 61-80 Drill Set

H77 Fine Oilstone

E97-4 Tonehole Set

E29 Wide Fine File

E29A Narrow Fine File

E18 Swiss Pattern File Set

R88 Filing Wood Block

E30 File Cleaner

G60 Jewelers Saw

D27-2,4 Blades

D20 Sm. Solid Shortener

D21 Lg. Solid Shortener

D29S Set of 5 Tubular Shorteners

F76 Music Wire Cutters

G62 Metal Back Saw

D32A/B Broaches

D15S Set of 11 Pvt Scrw Cntersnks

E47 Pivot Screw Key Reamers

E197 Pad Set Reamers

G44 Screw Slot Tool

G5A 4” Caliper

E46 Pad Gauge

G97 6” Scale

H56 Small Pin Vise

D44 Pin Prick Holder

E12 Brass Jaw Pliers

L20 Bench Anvil

G18 Center Punch

L62 Butane Bunsen

F97A Thin Jaw Duckbill

F48 Utility Pliers

F61A Parallel Pliers

116

W/W

SH

OP

SE

T U

P

Here is a list of tools by Gary Ferree, for a woodwind bench for most repairing, less than

overhauls. Everything is listed as a one of, to keep it simple. Sax pads are quite an expense

and are handled separately. Clarinet, Flute and other woodwind pads are more of an

individual thing, so that IS the way I handled them, they are here.

I have also, in good conscience, put some tools into a “community” bench because the less

incidence of repair vs. cost of tooling makes me go this way.

Suggested woodwind shop set up

Ferree’s saxophone pads

WHY 2 THICKNESSES?

IS .025” THAT IMPORTANT?

Most of our competitors stock only one

thickness of sax pad. We feel this is a big

mistake, because it COSTS YOU MORE

MONEY in the long run.

Most American saxes use the .185”

thickness as did the Selmer Paris and a few

other foreign saxes. A couple of American

saxes and now the Asian ones use the thinner

thickness.

If you stock only the thinner pad, then every

time you work on a horn designed to use

thicker pads, you have to spend 4-5 minutes

gluing or shimming the pad to make it thicker,

so it will hit in the back.

On the other hand, if you try to use a thicker

pad where a thinner one was designed to go,

you must bend down the front of the cup and

re-regulate everything to make it or them

work. This takes several minutes and with the

average shop time being worth about $1 a mi-

nute—that’s $4-5 of unbillable time wasted,

when you could have just popped in the right

thickness pad.

That is why Ferree’s stock both the .160”

and the .185” thicknesses. That is why “so

called budget pad distributors” stock an in

-between .170” or .175” pad, which is ac-

tually wrong for both situations and costs you

money.

ALL OF FERREE’S

WOODWIND PADS ARE

PROPORTIONAL IN

THICKNESS, THE SAME

AS THE PADS THAT

MANUFACTURERS USE ON

NEW INSTRUMENTS. IN

OTHER WORDS, THE SMALL-

ER PADS ARE SLIGHTLY

THINNER,

THE LARGER PADS ARE

SLIGHTLY THICKER.

USING THESE PADS, YOU

DO NOT HAVE TO MAKE

“SPECIAL ADJUSTMENTS” TO

GET THE PADS LEVEL

1. The most practical and economical way to

order pads is by the dozen or 100’s of each

size.

2. No orders can be filled for less than a doz-

en in each size and style, except sax pads

larger than 79/32nds or 62.5mm may be

ordered in half dozens.

3. The 100 pad price is applicable only when

the order is for 100 of the same size and

style pad.

4. Try to avoid ordering pad sets. This is

costly and not always satisfactory, since

there is sometimes a difference in a man-

ufacturers same model, due to different

punch press strengths when punching key

forms. If you do order sets, YOU MUST

MEASURE AND SPECIFY SIZES AND

QUANTITIES OF THE PADS to make up

the set. We cannot guarantee the fit of pad

sets ordered only by brand name. Pad sets

are NON-RETURNABLE.

5. Assortments of 200 pads are packaged in

one enveloped and are pre-made.

6. Assortments of 500 pads are packaged in

individual envelopes by size and are pre

-made. SUZY MEASURING PADS

117

SA

XO

PH

ON

E P

AD

S

FERREE’S SAXOPHONE PADS

Thickness .185”

B40

Plain Pad

Thickness .185”

B42

Rivet Pad

Thickness .160”

B43

Thin Pad w/flat

Metal Resonator

Thickness .185”

B44

Flat Metal Res-

onator Pad

B46

Thin Pad w/

Domed Metal

Resonator

Thickness .160” Thickness .185”

B47

Domed Metal

Resonator Pad

B50

Conn Reso Pad

w/Metal Ring

Thickness .165”

B60

Snap-On

(metal back)

Buescher pads

Asst. Thickness

B52

Thin pad w/

Selmer Type

Plastic Resonator

Thickness .160”

B53

Selmer Type

Plastic Resonator

Pad

Thickness .185”

B58

Thin Pad-

Center Hole

Thickness .160”

B59

Reg. Pad-

Center Hole

Thickness .185”

B64

De’Jur Thin Pad

Center Hole

Thickness .160”

B66

De’Jur Reg. Pad

Center Hole


B62

Ferree’s Cone

Style Plastic Res-

onator Pad

B56

Ferree’s Cone

Style Plastic Res-

onator Pad

Thickness .160”

118

SA

XO

PH

ON

E P

AD

S

FERREE’S SAXOPHONE PADS

INFORMATION FOR ORDERING SAX PADS.

MM 32/IN MM 32/IN MM 32/IN MM 32/IN MM 32/IN MM 32/IN

7 9/32 17.5 22/32 28 35/32 38.5 49 62/32 59.5 75/32

7.5 18 28.5 36/32 39 49/32 49.5 60

8 10/32 18.5 23/32 29 39.5 50 63/32 60.5 76/32

8.5 19 24/32 29.5 37/32 40 50/32 50.5 61 77/32

9 11/32 19.5 30 38/32 40.5 51/32 51 64/32 61.5

9.5 12/32 20 25/32 30.5 41 51.5 65/32 62 78/32

10 13/32 20.5 26/32 31 39/32 41.5 52/32 52 62.5 79/32

10.5 21 31.5 42 53/32 52.5 66/32 63

11 14/32 21.5 27/32 32 40/32 42.5 53 67/32 63.5 80/32

11.5 22 28/32 32.5 41/32 43 54/32 53.5 64

12 15/32 22.5 33 43.5 55/32 54 68/32 64.5 81/32

12.5 16/32 23 29/32 33.5 42/32 44 54.5 65 82/32

13 23.5 34 43/32 44.5 56/32 55 69/32 65.5

13.5 17/32 24 30/32 34.5 45 57/32 55.5 70/32 66 83/32

14 24.5 31/32 35 44/32 45.5 56 66.5 84/32

14.5 18/32 25 35.5 46 58/32 56.5 71/32 67

15 19/32 25.5 32/32 36 45/32 46.5 57 72/32 67.5 85/32

15.5 26 33/32 36.5 46/32 47 59/32 57.5 68

16 20/32 26.5 37 47.5 60/32 58 73/32 68.5 86/32

16.5 21/32 27 34/32 37.5 47/32 48 58.5 74/32 69 87/32

17 27.5 38 48/32 48.5 61/32 59 69.5

70 88/32

CONVERSION CHART (The closest standard comparison)

We are proud of our sax pads. Our sales

indicate that the majority of you are already

using our pads. If you are one of the few that

isn’t, we hope you’ll try them and see what

you’ve been missing.

We stock most of our saxophone pads in

millimeters as well as 32nds (except for B50,

B60, B64, & B66).

Measure your pads cups carefully or send

us a sample of the sizes you want.

The quality and sizing of Ferree’s sax pads

are consistently high. Each pad size has its own

special die for cutting and assembling. This

does away with the variation in thickness and

diameter that most distributors must contend

with. When we import a pad we check it to

insure that the sizing and quality is as true as

possible to the ones we make.

Ferree’s is the largest distributor of sax-

ophone pads in the United States. All Fer-

ree’s sax pads are made with 100% woven

wool felt, covered with a high grade, specially

selected, soft tan leather.

119

SA

XO

PH

ON

E P

AD

S

Saxophone pads

B42 (32nd) B42M (mm) Description

9 thru 19 7 thru 15.5 Plain Pads

20 thru 88 16 thru 70 Rivet Pads

MM’s Description 32nd’s

B42MA Soprano Sax B42A

B42MB Alto Sax B42B

B42MC C Melody Sax B42C

B42MD Tenor Sax B42D

B42ME Baritone Sax B42E

B42MF Bass Sax B42F

B42MG Alto Clarinet (newer) B42G

B42MH Bass Clarinet ( newer) B42H

B42M2 200 Pad Assortment B422


B425C B42M5C 500 Pad Assortment w/

cabinet

MM’s Description 32nd’s

B40MA Soprano Sax B40A

B40MB Alto Sax B40B

B40MC C Melody Sax B40C

B40MD Tenor Sax B40D

B40ME Baritone Sax B40E

B40MF Bass Sax B40F

B40MG Alto Clarinet B40G

B40MH Bass Clarinet B40H



B405C B405MC 500 Pad Assortment w/

cabinet

B40 IMPORTED PLAIN SAX PADS

These B40 Plain Sax Pads may be

ordered in 32nd sizes 9 thru 88 or in

Millimeter sizes from 7 thru 70 and

every half size. An ‘M’ in the

catalog number indicates

millimeter (metric) sizes.

SPECIFY SIZES IN 32NDS OR MILLIMETER

B40 B40M

32nd MM

9 thru 88 7 thru 70

B40 SETS AND ASSORTMENTS

State specific sizes for pad cups/pads when

ordering sets!

B42 SAX PAD WITH RIVETS

These B42 pads also fit most current model alto and bass clar-

inets. Pads may be ordered in 32nd sizes 9 thru 88 or in millime-ter sizes from 7 thru 70 and every

half size. An ‘M’ in the catalog number indicates millimeter (metric) sizes. Rivets used are our B230’s.


Thickness .185”



ordering sets!

120

SA

XO

PH

ON

E P

AD

S

Thickness .185”

Saxophone pads

32nd’s MM’s Description

B44A B44MA Soprano Sax

B44B B44MB Alto Sax

B44C B44MC C Melody Sax

B44D B44MD Tenor Sax

B44E B44ME Baritone Sax

B44F B44MF Bass Sax

B442 B44M2 200 Pad Assortment



cabinet



B43B B43MB Alto Sax




B43F B43MF Bass Sax




cabinet

B43 FERREE’S THIN PAD WITH FLAT

METAL RESONATOR

The B43 pad is slightly thinner

than the B44. It is used on

instruments like the Conn 6m,

10m, 12m, Yamaha, Martin and

most Asian saxes. An ‘M’ in the

catalog number indicates millimeter (metric) sizes.




ordering sets!

B44 FERREE’S REGULAR PAD W/FLAT

METAL RESONATOR

These B44 pads have stainless

steel resonators for a more brilliant

sound without distortion of tone. An

‘M’ in the catalog number

indicates millimeter (metric)

sizes.




ordering sets!



20 thru 25 16 thru 20 Rivet only

26 thru 88 20.5 thru 70 Rivet & Resonator





121

SA

XO

PH

ON

E P

AD

S


Saxophone pads



B47B B47MB Alto Sax




B47F B47MF Bass Sax




cabinet

B46 SELMER STYLE DOMED METAL

RESONATOR THIN PAD

Some musicians prefer the sound

obtained by the use of a domed

metal resonator. This pad has the

Selmer Style Domed metal res-

onator. These are just like the

domed metal resonators used on the Selmer Super

Action “80” Saxophones.




ordering sets!



B46B B46MB Alto Sax




B46F B46MF Bass Sax




cabinet

B47 SELMER SUPER EIGHTY STYLE

DOMED METAL RESONATORS

This pad is identical to the B46

listed previously, except it is the

standard thickness. Made with the

same metal domed resonator as

installed on the Selmer Super

Action “80” saxophones.




ordering sets!









122

SA

XO

PH

ON

E P

AD

S


Saxophone pads

B50 CONN RES-O-PADS WITH RING

The special metal ring in Conn

Res-O-Pads gives the pad a tighter

look. The front face (shown here) is

the larger diameter because of the

ring flange. NOTE: When

measuring for the Res-O-Pads, be

sure to measure the back side to

determine the size you need for replacement.

Better yet, measure the cup.



ordering sets!

32nd’s Description

B50A Soprano Sax

B50B Alto Sax

B50C C Melody Sax

B50D Tenor Sax

B50E Baritone Sax

B60 SNAP-ON (METAL BACK)

Available for Soprano thru Bar-

itone. These are the same as the

originally manufactured

construction. Sizes listed below

are the ONLY ones that we

have available.

We do NOT have the replacement snaps.

MM’s Description

B60MA Soprano Sax

B60MB Alto Sax

B60MC C Melody Sax

B60MD Tenor Sax

B60ME Baritone Sax



ordering sets!

SIZED IN 32NDS ONLY, as follows:

15, 18, 19, 20, 21, 22, 24, 26, 28, 30, 31, 32, 35,

36, 37, 38, 39, 42, 44, 47, 49, 51, 52, 55, 58, 60,

61, 64, 70, 78, 86 Mostly fit post WWII saxes.

SIZED IN METRIC ONLY, as follows:

10, 15, 17, 19, 20, 23, 24, 25, 27, 29, 31, 32, 34,

37, 39, 42, 46, 48, 50, 59 Mostly fit post WWII

saxes.

When ordering ANY SET, we can’t

guarantee it unless you provide the specific

sizes for the set.

**B50 Conn Res-o-pads are ONLY

AVAILABLE in the 32nd sizes listed

above.***

When ordering ANY SET, we can’t

guarantee it unless you provide the

specific sizes for the set.

B60 Snap-On pads are ONLY

AVAILABLE in the mm sizes above.

123

SA

XO

PH

ON

E P

AD

S

Thickness .165”

Older Conn

Only

Thickness Asst.

As per original



B52B B52MB Alto Sax




B52F B52MF Bass Sax




cabinet

B52MY264 Sm. Asst. for Yamaha

B52MY504 Lg. Asst. for Yamaha

B52MYOLD Add’l pads for pre-’88’

B52MYBAR Add’l pads for baritone

Saxophone pads

B52 FERREE’S THIN SAX PADS W/

SELMER TYPE PLASTIC RESONATOR



ordering sets!

B53 SELMER TYPE SAX PADS

These B53 standard medium, .185”

thick pads have the smooth plastic

Selmer-type resonators. Pads may

be ordered in 32nd sizes 9 to 88 or

in millimeter sizes 7 thru 70 and

every half size. An M in the cat-

alog number indicates millimeter (metric) size.

.185” thick.



ordering sets!

Here’s that standard thin pad, .160”

thick (4mm), with the plastic

resonator that you’ve been looking

for. The domed plastic tone res-

onator in each pad looks similar to

the original resonators used by

leading saxophone manufacturers. An M in the

catalog number indicates millimeter (metric) size.

.160” thick.


B52(32nds) B52M

9 thru 19 7 thru 15.5 Plain pads

20 thru 88 16 thru 70 Resonator pads

B53(32nds) B53M






B53B B53MB Alto Sax




B53F B53MF Bass Sax




cabinet

124

SA

XO

PH

ON

E P

AD

S




B59B B59MB Alto Sax




B59F B59MF Bass Sax




cabinet



B58B B58MB Alto Sax




B58F B58MF Bass Sax




cabinet

Saxophone pads

B58 UNIVERSAL SAXOPHONE



ordering sets!

B59 UNIVERSAL SAXOPHONE PADS

These pads have a hole pre-punched in the center and are the

standard medium .185” (4.7mm) thick. They DO NOT have any rivets or resonators installed. This

allows the repairman to match the style of resonator to the instrument being repaired. Another important advantage is the diameter of the

resonator can be hand selected to cover more of the surface of the pad without touching the tone hole chimney. This creates the maximum amount of

resonating surface. Using this series of Universal Sax pads along with

a B260 or B265 Universal Resonator kit will elim-inate the need to stock several different lines of sax-ophone pads. Available in dozens and hundreds in

32nd sizes 9 thru 88 and metric sizes, 7 thru 70, by half sizes.



ordering sets!

These pads are similar to the B59 Universal Saxophone Pad except the

B58 is the standard thin, .160” (4mm). It has a pre-punched center hole, but DOES NOT have any rivets or res-

onators installed. This allows the re-pairman to match the style of the resonator to the in-strument being repaired.

Another important advantage is the diameter of the resonator can be hand selected to cover more of the surface of the pad without touching the tone hole

chimney. This creates the maximum amount of res-onating surface.

Using the series of Universal Sax pads along with a B260 or B265 Universal Resonator kit will eliminate the need to stock several different lines of saxophone

pads. Available in dozens and hundreds in 32nd sizes 9 thru 88 and metric sizes, 7 thru 70, by half sizes.

B58P Plain 9-31/32

B58 With hole 20-88/32

B58PM Plain 7-25mm

B58M With hole 16-70mm

B59 Plain 9-19/32

With hole 20-88/32

B59M Plain 7-15.5mm

With hole 16-70/32

125

SA

XO

PH

ON

E P

AD

S

Thickness .160”

Standard Thin Thickness .185”

Standard Size

Saxophone pads

B64 DE’JUR DELUXE THIN

SAX PADS B66 DE’JUR DELUXE SAX PADS

This line of pads is similar to the B64 De’Jur a thicker .185” (4.7mm)

pad. These pads can come with a pre-punched center hole, a rivet, a plas-

tic resonator, or a domed metal reso-nator. By request.

Available in METRIC sizes only from 7mm thru

70mm by half sizes. Resonators and Rivets are available for sizes 16 and above. The B66 De’Jur pads are standard medium .185” (4.7mm) thick.

Holes start at size 16.

These beautiful, perfectly

pneumatic skin pads have a very

fine texture unlike most pads. The

B64 is a standard thin .160” (4mm)

pad.

These pads can come with a pre-punched center

hole, a rivet, a plastic resonator, or a domed metal

resonator. As per your request.

Available in METRIC sizes only, from 7mm to

70mm by half sizes. Resonators and Rivets are

available for sizes 16 and above. The B64 De’Jur

pads are standard thin .160” (4mm) thick. Holes

start at size 16.

B64 DE’JUR DELUXE SAX PADS

MILLIMETERS ONLY

**ORDER BY STYLE AND SIZE**

B64M PLAIN 7-70, holes 16 up

B64V RIVET 16-70

B64R PLASTIC RESONATOR

16-70

B64D DOMED METAL RESO.

16-70

SIZES AVAILABLE:

7 thru 15.5 Plain pads

16 thru 70 Hole, Rivet or Resonators

B66 DE’JUR DELUXE SAX PADS

MILLIMETERS ONLY

**ORDER BY STYLE AND SIZE**

B66M PLAIN 7-70, holes 16 up

B66V RIVET 16-70

B66R PLASTIC RESONATOR

16-70

B66D DOMED METAL RESO.

16-70

SIZES AVAILABLE:


16 thru 70 Hole, Rivet or Resonators

NO Assortments NO Assortments

126

SA

XO

PH

ON

E P

AD

S


MM’s Description

B62MA Soprano Sax

B62MB Alto Sax

B62MC C Melody Sax

B62MD Tenor Sax

B62ME Baritone Sax

B62MF Bass Sax

B62M2 200 Pad Assortment

B62M5 500 Pad Assortment

B625MC 500 Pad Assortment w/

cabinet



B56B B56MB Alto Sax




B56F B56MF Bass Sax




cabinet

Saxophone pads

B56 FERREE’S CONE RESONA-

TOR Standard Thickness SAX PADS

FERREE’S NEW

B62 CONE

RESONATOR FOR

NEW ASIAN SAXES The tried and true B56 Elliptical Cone Resonator Sax Pads have

convex resonators made of the same material as our Selmer Type res-onators. The special cone shape pro-

vides 360° airflow management and sound reflection to direct the sound

and air out from under the pad, instead of bouncing

it back into the sax, greatly improving resonance and performance. It is molded with a solid construction and flat back. The B56 Cone Resonator fits the pad

naturally and blends well with other resonators when being used as a replacement. By half millimeters.

Cones are brown only.


B56(32nds) B56M




B62M MILLIMETERS ONLY


16 thru 70 Resonator pads

The New B62 Elliptical Cone Res-onator Sax Pads have convex reso-

nators made of the same materi-al as our Selmer type resonators. Now, available in STANDARD

THIN for the newer Asian saxes. The proven cone shape provides 360° airflow man-agement and sound reflection to direct the sound and

air out from under the pad, instead of bouncing it back into the sax, greatly improving resonance and performance. It is molded with a solid construction

and flat back. The B62 Cone Resonator blends well with other resonators when being used as a replace-

ment. By half millimeters. Cones are brown only.

127

SA

XO

PH

ON

E P

AD

S

Standard

Thickness .185” Standard Thin

Thickness .160”

RESONATORS & MISC.

B56R STYLE CONE RESONATORS

This is the resonator used on the popular B56 and

B62 Cone Style Resonator Pads.

Provides 360° airflow management and sound

reflection to direct the sound and air out from under

the pad instead of bouncing it back into the sax,

greatly improving players response and performance.

Available only in the color BROWN.

SIZE O.D. Fits MM

Pad Sizes

Fits 32nd

Pad Sizes

B56R 1 .312”(7.9mm) 16-22.5 20-28

B56R 2 .445”(11.3mm) 23-26.5 29-33

B56R 3 .570”(14.5mm) 27-30 34-38

B56R 4 .700”(17.8mm) 30.5-34.5 39-43

B56R 5 .820”(20.8mm) 35-38.5 44-48

B56R 7 .950”(24.1mm) 39-43 49-54

B56R 8 1.075”(27.3mm) 43.5-48.5 55-61

B56R 10 1.200”(30.5mm) 62-71 49-56.5

B56R 11 1.325”(33.7mm) 72-88 57-70

ITEM NUMBER DESCRIPTION

B56RA Alto Sax Set

B56RT Tenor Sax Set

B56RB Baritone Sax Set

**HEAT STAKING TOOL REQUIRED**

UNIVERSAL RESONATOR KITS

The Universal Resonator Kits have an assortment

of metal and plastic resonators along with rivets

and installation tools. These kits were designed for

Repairmen who want to install the correct style and

size resonator in the B58 or B59 Sax Pads. Using

the resonators from the kit shown below, along

with the B58 and B59 Sax Pads will be particularly

useful when replacing only one or two pads on an

instrument. When the new pad resonator matches

the existing pad resonators a more professional

looking job is realized. All of the resonators and

rivets can be ready for even the biggest jobs. Both

kits come with an attractive storage case to keep

the assortment in order.

The B260 Economy Universal Resonator Kit

contains: 500 rivets for flat steel resonators, 200

long rivets for domed steel resonators, 50 each of

3/8”, 1/2”and 3/4” flat steel resonators, 12 each of

the nine sizes of Selmer style brown plastic res-

onators, 12 each of the nine sizes of Ferree’s cone

style resonators 3/8”, 1/2”. 5/8”, 3/4”, 1”, 12 each 1

-5/16” domed steel resonators, one each of the D28

Rivet Punch and the D41 Heat Staking Tool.

The B265 Deluxe Universal Resonator Kit

contains: 2000 rivets for flat steel resonators, 800

long rivets for domed steel resonators, 200 each of

3/8”, 1/2” and 3/4” flat steel resonators, 48 each of

Selmer style brown plastic resonators, 48 each of

the nine sizes of Ferree’s cone style plastic res-

onators, 96 each of the domed steel resonators, one

each of the D28 Rivet Punch and the D41 Heat

Staking Tool.

B260 Economy Resonator Kit

B265 Deluxe Resonator Kit

128

Notes from customers: “Thanks so much for your quick response!

I wasn’t expecting anybody to be replying to

business mail on Labor Day”...Mike.

RE

SO

NA

TO

RS

& M

ISC

.

SETS OF B45R DOMED

METAL RESONATORS

RESONATORS & MISC.

B45R SELMER “SUPER 80” TYPE

METAL DOME RESONATORS

B53R SELMER TYPE

RESONATORS

SIZE O.D.

IN

O.D.

MM

Fits MM

Pad Sizes

B45R 1 3/8” 9.5mm

B45R 2 1/2” 12.7mm

B45R 3 5/8” 15.9mm 26 thru 32

B45R 4 3/4” 19.1mm 34 thru 40

B45R 5 1” 25.4mm 44 thru 46

B45R 6 1-5/16” 33.3mm 52 thru 63


B45RA Alto Sax Set

B45RT Tenor Sax Set


(Note: Be sure to order B235 extra long rivets to

attach these resonators.

FLAT METAL RESONATORS (Type used on B43 and B44 sax pads)

O.D. IN O.D. MM Fits 32nd

Pad Sizes

Fits MM

Pad Sizes

B220 3/8” 9.5mm 26 thru 35 20.6 thru28

B221 1/2” 12.7mm 36 thru 46 28.5 thru 36.5

B222 3/4” 19mm 47 thru 88 37.5 thru 70

B223 7/8” 22.2mm

This is like the res-

onator used on the

popular Selmer Mark

VI Saxophone.

Available only in the

color BROWN.

SIZE O.D. Fits MM

Pad Sizes

Fits 32nd

Pad Sizes

B53R 1 .312”(7.9mm) 16-22.5 20-28

B53R 2 .445”(11.3mm) 23-26.5 29-33

B53R 3 .570”(14.5mm) 27-30 34-38

B53R 4 .700”(17.8mm) 30.5-34.5 39-43

B53R 5 .820”(20.8mm) 35-38.5 44-48

B53R 7 .950”(24.1mm) 39-43 49-54

B53R 8 1.075”(27.3mm) 43.5-48.5 55-61

B53R 10 1.200”(30.5mm) 62-71 49-56.5

B53R 11 1.325”(33.7mm) 72-88 57-70


B53RA Alto Sax Set

B53RT Tenor Sax Set


**HEAT STAKING TOOL REQUIRED**

D41 HEAT STAKING TOOL

This is the tool

used to install

individual Plastic

Resonators. Heat the

tool and use it to

bend over the res-

onator tower on the

back of the pad.

D41 Heat Staking Tool 129

RE

SO

NA

TO

RS

& M

ISC

.

F6 BENCH HAMMER

This is a

utility hammer

for flattening

needle springs

and other light

uses.

F6 Bench Hammer

D73A———

Length .660”

Thick. .010”, .012”, .014” or .016”

D73A———

Length .800”

Thick. .010”, .012”, .014” or .016”

D73B———

Length 1.000”

Thick. .010”, .012”, .014” or .016”

D73B———

Length 1.185”

Thick. .012”, .016”, .018”, .020”,

or .022”

D73C———

Length 1.555”

Thick. .012”, .020” or .029”

D73C———

Length 1.725”

Thick. .014”

D73C———

Length 2.075”

Thick. .010” or .012”

D73D———

Length 1.125”

Thick. .009”

(for flute, with square back)

B230 & B235 SAX PAD RIVETS

Sold by the 100’s or 1000’s

B230 Regular rivets 7/32” L (5.6mm)

B235 Extra long rivets (used to attach

B45R Resonators) 10/32” (7.9mm)

(Semi-Hollow)

D28 PAD RIVET PUNCH

Used to form the end of a tubular rivet after it

has been inserted through sax pad hole.

D28 Pad Rivet Punch

Woodwind springs

D73 PHOSPHOR BRONZE

FLAT SPRINGS A few years back the price of the blued

flat springs increased dramatically. Immediately,

Ferree’s started looking for a less expensive source.

Now we’ve found it.

The phosphor bronze flat springs are not only less

expensive than the blued flat springs, they have

several other advantages.

~A special size to fit flutes.

~Phosphor bronze color with a round back (except

flute, which has a square back).

~Rust and corrosion resistant.

~Available in “generic sizes” to fit more horns. Can

be cut to match the needed size exactly.

~Being used on most of the newer horns, so you will

be able to keep your customer’s horn “original

equipment.”

~Longer lasting.

The springs are available in individual sizes

(specify thickness and length), sold in dozens or

hundreds. Also, available are two handy

assortments, packaged in individual vials, mounted

in an attractive wood holder, in 350 and 500

quantities. Order today and start saving money.

Phosphor Bronze Flat Springs with Round Back

D73E Assortment of 350 with vials and holder

D73F Assortment of 500 with vials and holder

D73W Extra wood block to hold vials 130

WO

OD

WIN

D S

PR

ING

S

VISITORS

Long time customer, Pat Hiatt, visits

with Katherine

D61B D61A

Woodwind springs

D80A Stainless Steel Round Springs-

.018”-.040”, state size, dozens or hundreds

D80B Stainless Steel Round Springs-

.042”-.064, state size, dozens or hundreds

D80C Assortment of 100 Stainless Steel Round

Springs

D80D Assortment of 350 Stainless Steel Round

Springs

D80E Assortment of 500 Stainless Steel Round

Springs

D80W Wood block to hold vials

D80VS Small vials for D80

D80VL Large vials for D80

Dia. Len. Dia. Len.

(in) (mm) (in) (mm)

.018 X 30 .030 X 50

.021 X 30 .032 X 50

.022 X 58 .034 X 50

.023 X 16 .036 X 31

.024 X 40 .036 X 35

.027 X 16 .036 X 38.5

.027 X 40 .036 X 50

.029 X 22 .037 X 50

.029 X 28

D60 NORTON SPRINGS

FOR BUESCHER SAXES The first two digits of the style number indicates

the music wire gauge. The second two digits

indicate the length in millimeters. This information

should help you determine what springs you need.

The style numbers available are the longest length

of each gauge so you can cut them to length.

D60 Sizes: 0830, 1240, 1650, 2065, 2485

D80 STAINLESS STEEL

ROUND SPRINGS These are the round springs like the ones used by

most manufacturer’s student instruments today.

Rust proof with smoother, more fluid action. Each

spring comes pre-flattened on one end. The other

end can be cut to the required length.

O.D. Length O.D. Length

.018” X 30mm .042” X 60mm

.020” X 30mm .044” X 60mm

.022” X 30mm .046” X 60mm

.024” X 40mm .048” X 60mm

.026” X 40mm .050” X 60mm

.028” X 40mm .052” X 60mm

.030” X 50mm .054” X 85mm

.032” X 50mm .056” X 85mm

.034” X 50mm .058” X 85mm

.036” X 50mm .060” X 85mm

.038” X 50mm .062” X 85mm

.040” X 50mm .064” X 85mm

D80A D80B

The first two numbers are the diameter in wire gauge.

The second two numbers are the length in millimeters.

#08=.024” wire We carry size 0830, which is 30mm long





~All Norton springs are a American 3-48 thread.~

D61A Blued Needle Springs size .018”-.037”

D61B Blued Needle Springs size .040”-.064”

D61C Assortment of 100 springs

D61D Assortment of 350 springs sorted in vials

and a wood holder

D61E Assortment of 500 springs sorted in vials

and a wood holder

D80VS Small vials (work with D61)

D80VL Large vials (work with D61)

D61W Wood block to hold vials 131

WO

OD

WIN

D S

PR

ING

S *NEW* D60B NORTON SPRING BUSHING

You can make the hole in the D60 Norton Spring

Bushings. With these machine solid brass bushings you

can install any size spring you want with any type material

(blue, bronze, nickel or stainless) with any useable

diameter YOU want...Just drill .024” pilot hole larger, if

necessary.

D61 BLUED NEEDLE SPRINGS Traditional blued needle springs. Now you can match the springs in the woodwinds that use this type of

spring. Also, useful for fitting into the small spring hook on some woodwind keys that the standard round spring will not fit into. Leave the needle end alone and

cut the spring at the other end to any required length.

Dia. Len. Dia. Len.

(in) (mm) (in) (mm)

.040 X 50 .053 X 85

.043 X 60 .054 X 53

.044 X 38 .056 X 85

.044 X 42.5 .060 X 85

.044 X 46 .064 X 85

.044 X 54.6

.044 X 57

.046 X 60

.050 X 60

Item Number Description

D63A A Key

D63B Register Key

D63C Eb - Bb Trill Key

D63D Bb - C Trill Key

D63E F# - C# Trill Key

D63F G - D Key

D74 Piccolo & Flute Spring Wire-Phos/Bronze

D74-ASST 1 foot of each Spring Wire

Woodwind springs

D62 VITO FLAT SPRINGS

Springs to fit the genuine LeBlanc/Noblet/

Vito keys listed below. We have both the

Beryllium Copper Flat Springs to fit the Vito

Soprano Clarinet and the Blued Steel Springs

to fit the Vito Bass Clarinet

D62 Beryllium Copper Springs-Soprano Clarinet

Item Number Description

D62A A Key

D62B Bb Trill Key

D62C Register Key

D62D F# - C# Trill Key

D62E C Trill Key

D62F Eb - Bb Trill Key

D63 Blued Steel Springs-Bass Clarinet

FLUTE AND PICCOLO SPRING WIRE Phosphor Bronze and Nickel Silver

.025”

Nickel/Silver

(.6mm)

.032”

Nickel/Silver

(.8mm)

.036”

Nickel/Silver

(.9mm)

D72 Piccolo & Flute Spring Wire-Nickel Silver

D72-ASST 1 foot of each size Spring Wire

.020”

Phos/Brnz

(.5mm)

.025”

Phos/Brnz

(.6mm)

.032”

Phos/Brnz

(.8mm)

.036”

Phos/Brnz

(.9mm)

D70 FLAT SPRINGS FOR

CLARINET

These blued steel springs

are rust resistant.

THICKNESS LENGTH SUGGESTED USE

.010” X 44mm Octave key short

.011” X 58mm Octave key long

.011” X 13mm A key short

.011” X 17mm A key long

.011” X 29.5mm Side Bb Trill

.016” X 16.5mm Trill Keys

.016” X 19mm Trill Keys



D70 Flat Clarinet Springs-state size

D70A Assortment of 100 Clarinet Flat Springs

D70B Assortment of 500 Flat Springs for

clarinet and sax. Comes sorted in plastic

vials in a wood holder.

D70C Assortment of 350 Flat Springs for

clarinet and sax. Comes sorted in plastic

vials in a wood holder.

D70VS Small vial to hold flat springs

D70VL Large vial to hold flat springs


FLAT SPRINGS FOR SAXOPHONE

D71 Flat Saxophone Springs-State size

D71A Assortment of 100 Sax Flat springs

D70B Assortment of 500 Flat Springs for sax

and clarinet. Comes sorted in plastic vials

in a wood holder.

D70C Assortment of 350 Flat Springs for sax

and clarinet in plastic vials in a wood

holder


(use D70VS and D70VL vials above)

Thickness Length Thickness Length

.006” X 25mm .018” X 30mm

.013” X 30mm .022” X 30mm

.015” X 30mm .029” X 36mm

.017” X 25mm

132

WO

OD

WIN

D S

PR

ING

S

C75HB 1/4-20 thread, brass

C75HN 1/4-20 thread, nickel

C75JB 5/16-24 thread, brass

C75JN 5/16-24 thread, nickel

C75KB 1/4-28 thread, brass

C75KN 1/4-28 thread, nickel

C75LB 1/4-24 thread, brass

C75LN 1/4-24 thread, nickel

C70AB 6-32 thread, brass

C70AN 6-32 thread, nickel

C70BB 6-36 thread, brass

C70BN 6-36 thread, nickel

C70CB 6-40 thread, brass

C70CN 6-40 thread, nickel

C70DB 8-32 thread, brass

C70DN 8-32 thread, nickel

C70EB 8-36 thread, brass

C70EN 8-36 thread, nickel

C77HB 1/4-20 thread, brass

C77JB 5/16-24 thread, brass

C77KB 1/4-28 thread, brass

C77LB 1/4-24 thread, nickel

C71AB 6-32 thread, brass

C71AN 6-32 thread, nickel

C71BB 6-36 thread, brass

C71BN 6-36 thread, nickel





C71FB 4-.75mm thread, brass

C71FN 4-.75mm thread, nickel

The C70 Screw Assortment Kit of 100 Screws

includes:

5 sizes of lyre screws

2 sizes of baritone bell screws

2 sizes of large wing screws for saxophone or

sousaphone mouth pipes

5 sizes of ligature screws

4 sizes of sousaphone bell screws

Designed to fit both foreign and domestic instruments.

A chart in the lid of the partitioned plastic box shows the

kind of screw, thread size and brand of instrument the

screw will fit. All screws are precision made and are

available in brass or nickel finish. The kit has screws of

both finishes.

INSTRUMENT SCREWS

REPLACEMENT SCREWS & NUTS FOR THE C70 KIT We stock only one length in the lyre and baritone bell screws. These can be cut off with a

jeweler’s saw, if a shorter length is needed. After cutting off the screw, then gently round the edge

of the cut end with a file or Z2 Band Sander

LYRE SCREWS

LIGATURE SCREWS


C72DN 8-32 thread. nickel

C72GB 10-32 thread, brass

C72GN 10-32 thread, nickel

BARITONE BELL SCREWS



BARITONE BELL NUTS






C73GN 10-32 thread, nickel

SAX & SOUSAPHONE

NECK SCREWS

C74FB 4-.75mm thread, brass

C74FN 4-.75mm thread, nickel

SAX NECK SCREWS

SOUSAPHONE BELL

SCREWS

SOUSAPHONE BELL

NUTS

To keep your C70 Screw

Kit ready for everything,

reorder screws frequently.

You will find replacement

screws listed in the

columns on this page. 133

INS

TR

UM

EN

T S

CR

EW

S

CONN, PAN AMERICAN

C47 Alto sax, toolsteel set screw(.110 L X .070D)

C5CF5 Clar./flute flat spring screw

C5F1 Flute pivot screw

C5F6 Flute pad screw

C5F7 Flute pad washer

C5F8 Flute pad cup spuds

C5F10 Flute crown, silver plate

C5F11 Flute crown, nickel

C5NC1 New clarinet pivot screw

C5NSA1 New saxophone pivot screw

C5OC1 Old clarinet pivot screw

C5SA2 Key guard screw

C5SA5 Saxophone flat spring screw (0-80)

EMERSON


C19F4 Flute adjustment screw, w/head

C19F5 Flute flat spring screw


C19F7 Flute pad washers

C19F9 Flute grommets

DEFORD


C6F4 Flute adjustment screw, w/o head


C6F6 Flute pad screw (1-64)


C6F8 Flute spuds

C6F9 Flute grommets



BUFFET

C4B1A Bassoon pivot screw, new, headless

C4F1 Flute pivot

C4NC1 New model clarinet pivot screw

C4OC1 Old clarinet pivot screw (1-72)

C4SA1 Saxophone pivot screw (3-.5mm)

C4SA2(S) Sax key guard screw, small

C4SA2(L) Sax key guard screw, large


C3SA5 Saxophone flat spring screw

Woodwind screws & flute parts

ARMSTRONG

C1CF5 Clar./flute flat spring screw


C1F4 Flute adjustment screw



C1F8 Flute spuds

C1F9 Flute grommets (for open hole)



C1NS1 Alto saxophone pivot screw

C1SA2 Sax key guard screw

ARTLEY

C2C1 Clarinet pivot screw

C2CF5 Clar/flute flat spring screw





C2F8 Flute spuds

C2F9 Flute grommets

C2F10 Flute Crown, silver plate

C2F11 Flute Crown, nickel

BLESSING

C20SA1 Saxophone pivot screw

BUNDY, BUESCHER

C3AC1 Alto clarinet pivot screws

C3ARC1 Alto clarinet/bass clarinet adjustment screw

C3B1 Bassoon conical pivot screw, all models

C3BC1 Bass clarinet pivot screw


C3C3 Clar. G# adjustment screw(nylon, no head)

C3C5 Flat spring screw, clarinet and flute



C3F5 Flat spring screw, clarinet and flute



C3F8 Flute spuds

C3F9 Flute grommets



C3OB1 Oboe pivot screw

C3SA1 Saxophone pivot screw

134

W/W

SC

RE

WS

& F

L. P

AR

TS

LEBLANC, NOBLET, NORMANDY

C13AC4 Leblanc, Noblet, alto/bass clarinet adj

C13C1 Leblanc, Noblet, clarinet pivot screw, old w/

head

C13C5 Leblanc, Noblet, clarinet flat spring screw

C13C12 Thumb rest screw

C13F1 Noblet, Normandy flute/oboe pivot screw

C13F4 Noblet, Normandy flute adj. screw

C13F6 Noblet, Normandy flute pad adj screw

C13NC1 Leblanc, Noblet, old Normandy clarinet piv-

ot screw, headless (use 3-56 Tap)

SELMER-NEW MODEL

C16AC1 Alto/Bb clarinet pivot screw

C16AC4 Alto/bass clarinet adj. screw

C16BC1 Contra & bass clarinet pivot screw

C16B1 Bassoon pivot screw


C16C5 Clarinet flat spring screw

C16F1 Flute pivot screw-New model





C16F8 Flute spuds

C16F9 Flute grommet


C16OB4 Oboe adjustment screw



C16SA5 Saxophone flat spring screw (0-80)

SCHREIBER

C4B1A Bassoon pivot screw, new, headless


C4OC1 Clarinet pivot screw

MARTIN

C17BS2 Martin baritone sax key guard screw

(same as Vito baritone sax)

C15TS2 Martin tenor sax key guard screw

HOLTON

C17BS2 Holton baritone sax key guard screw (see Vito)

JUPITER


C11C3 Clar. G# adjustment screw(nylon, w/head)







C11F9 Flute grommets



C11SA1 Sax pivot screw

C11SA2L Key guard screw, large

C11SA2S Regular key guard screw

C11SA5 Sax flat spring screw (1-72)

LINTON






FOX, RENARD


C7OB1 Renard, Oboe pivot screw

GEMEINHARDT


C8F4 Flute adjustment screw, w/head




C8F8 Flute spuds

C8F9 Flute grommets



HAYNES




KING & CLEVELAND





135

W/W

SC

RE

WS

& F

L. P

AR

TS

MISCELLANEOUS

C41 7.3mm French clarinet pivot screws (use #55 drill)

C44 8.1mm French clarinet pivot screws

C46 French clarinet flat spring screw

C49 Sax flat spring screw (0-80, Thread Length: .110”,

Overall L:.140”,Head Dia:.100”, flat head (slotted)

C50 Nickel silver screw for thumb rests, etc.

C50T Tap for C50 screws

C51 Oversize thumb rest screw

C60 Universal nylon tone boosters for flute

A52 French plugs for open hole flutes, metal disc (set of 5)

A52P French plugs for open hole flutes, plastic (set of 5)


VITO


C17AC4 Alto/bass clarinet adj. screw

C17AS1 Alto sax pivot screw (5-40)

C17AS5 Alto sax flat spring screw

C17BC1N Bass clarinet pivot screw headless-After 1990

C17BS2 Baritone sax key guard screw

C17NC1 Clarinet pivot screw

C17C4 Clarinet adjusting screw(metal)

C13C14 Vito clarinet coil springs

YAMAHA



C18C3 Clar. G# adjustment screw(metal)






C18F10 Flute crown, silver


C18NS2 Yamaha neck screw 4mm X .70



C18SA2 Saxophone key guard screw

PIVOT SCREW ASSORTMENTS

C30 Clarinet, 100 assorted

C31 Saxophone, 100 assorted

C32 Flute, 100 assorted

C35 All instruments, 100 assorted

CONTACT US FOR

CURRENT PRICING ON

ALL SCREWS. THEY

ARE NOT IN OUR

PRICE LISTS DUE TO

PRICE FLUCUATION.

—New Selmer M3.0x0.5 (like Series III)

and Old Selmer M3x0.6 (like Mk. VI) piv-

ot screws.

—New Selmer M4.0x0.7 (like Series III)

and Old Selmer M4x0.75 (like Mk. VI)

neck screws (We do not carry these. This is for reference).

—It is difficult to rethread, using a finer

thread over a coarser thread, as there is less

material available and it may easily strip.

Therefore, this is not suggested. You can

always thread a coarse thread where a fine

one was, because there is more material

available and you will be in some “new”

territory and is the preferred method.

136

W/W

SC

RE

WS

& F

L. P

AR

TS

H56 PIN VISE TOOL HOLDER

Quick on and off handle for small tools such as

counter sinks and pivot screw key reamers. Two

chucks. Chuck capacity is 0 to .128” (3.25mm).

H56 Pin Vise Holder with Two Chucks

ACCORDIoN tools

E13 THREE WAY

ACCORDION PLIERS

One end of both jaws is designed to crease and

bellows corners. The center section has round lips

with beveled hole enabling the plier to remove

accordion pins without marring the pins or the

accordion. The other edge of the plier is a nip nose

cutting plier for nipping off accordion rods in the

bass mechanism.

E13 Accordion Pliers

F17 TREBLE KEY

ADJUSTING TOOLS

Set of two Treble

Adjusting Tools.

One curved, one

straight, each

double ended.

Designed to bend

and adjust treble

key rods when

leveling the piano keyboard and correcting leaks

over the tone holes.

F17 Key Adjusting Tools

D43 BASS BUTTON

ADJUSTING TOOL

A double-ended tool used to straighten bass

buttons without removing the complete bass

mechanism.

D43 Bass Button Adjusting Tool

G93 BEESWAX Pure refined beeswax for waxing in accordion

reeds.

G93A 1/2 lb (227g) of beeswax

G93B 1 lb (454g) of beeswax

G80 BASS MECHANISM AND BASS

VALVE ADJUSTING TOOLS

With this set of 6 tools

practically any part of

the bass mechanism can

be reached and adjusted.

G80 Accordion Bass Adjusting Tool

G81 REED TESTING

AND TUNING TOOLS

A set of three hand

made accordion reed

tuning and adjusting

tools.

G81 Testing and Tuning Tools

E56 WAX SPOON Special wax spoon made

of copper to hold heat. Used

to place wax around reeds.

E56 Wax Spoon

137

AC

CO

RD

ION

TO

OL

S

G84 Small Tenon Set

E31 Inside Boring Bar

G72B (3) Wood Plug for Bb sop.

G72C (6) Plastic Plug for Bb sop.

G72C (2) Plastic Plug for Alto Clar.

G72D (1) Wood Plug for Bass Clar.

G72E (2) Plastic Plug for Bass Clar.

G72F (1) Wood Plug for Bass Clar.

G85 Oboe Tenon Set

G71 Bell Tenon Set

G66 Lower Tenon Plug Holder

G106 Bell Tenon Reamer

G73 (3) Plastic Plug for Bb sop.

G73 (2) Wood Plug for Bb sop.

G50 Bassoon Tenon Set (wing jnt)

G50B (3) Tenon Plug (abs)

G50C (2) Tenon Plug (aluminum)

G51 Bassoon Tenon Set (bass jnt)

G51A (3) Tenon Plug (maple)


G52 Bassoon Tenon Set (bell jnt)

G52A (2) Tenon Plug (maple)


G86 Clarinet Tone Hole Cutter St

G87 Set of 3 Tapered Tone Hole Cut-

ters

138

SUGGESTED SPECIALTY W/W TOOLS

SP

EC

IAL

TY

W/W

TO

OL

S

While minimal in the total scheme of things, this work is specialty for some. So, for

future consideration, perhaps.

We don’t sell lathes, so we will recommend www.grizzley.com as a possible source for

lathes, THERE ARE OTHERS. I know Repairmen who have gotten them there and they

are pleased. The models G9972Z, G4000 and G9729, look most useful. I’ve seen a couple

of them and they look clean and substantial.

G100 Lg. Solid Shortener

G104 Bass Clar. Tone Hole Cutter

G74S Raised Tone Hole Jig

G74A Raised Tone Hole Jig for Alto & Bass

Clar.

G53 Soprano Clar Tone Hole Undercutter

Set (6 in set)

G54 Bass Clar. Set as above (7 in set)

G78 Socket Grafting Jig

G76 Special Oboe Arbor for G78

G79B (2) ABS Graft

G79A Wood Graft

G77 Special Bass Clar. Arbor Kit

E57A Small Post Body Countersink

E57B Large Post Body Countersink

*** Extra ABS for toneholes, sockets,

tenons, ect..pg 110

F25 Dual Purpose Vise

E67 Post Locking Screw Set

E68/E69 Adj. Post Body Countersinks

R70 CORK GREASE Excellent non-drying cork grease in easy to use

plastic lipstick-type tubes, or in a one pound

container.

R70 (by the each, dozen or gross)

R71 (by the 1 lb container)

Cork products

CORK WASHERS (Sold by the dozen or hundred)

For Cornet and Trumpet 1/2” (12.7mm) O.D.

A14 1/16” (1.6mm) thick

A15 1/8” (3.2mm) thick

A16 3/16” (4.8mm) thick

A17 1/4” (6.4mm) thick

For Baritone and Bass 5/8” (15.9mm) O.D.

A1 1/16” (1.6mm) thick

A2 1/8” (3.2mm) thick

A3 3/16” (4.8mm) thick

A4 1/4” (6.4mm) thick

A51 100 Assorted precut cork washers

FRENCH HORN STRAIGHT

CORKS (Sold by the dozen or hundred)

Solid straight corks for French horns. All are

1-1/2” (38.1mm) long.

A18A 3/16” (4.8mm) thick

A18B 1/4” (6.4mm) thick

A18C 5/16” (7.9mm) thick

A18D 3/8” (9.5mm) thick

WATER KEY CORKS (Sold by the dozen or hundred)

Straight

A27 5/16” (7.9mm) O.D.

A28 3/8” (9.5mm) O.D.

A29 7/16” (11.1mm) O.D.

Tapered

A33 5/16” (7.9mm) O.D.

A34 3/8” (9.5mm) O.D.

A35 7/16” (11.1mm) O.D.

A36 1/2” (12.7mm) O.D.

A50 100 Assorted precut straight and

tapered water key corks

PRECUT FLUTE KEY CORKS

Come round. Cut into 3 or 4 pieces. Radius

matches flute trills and thickness for D#/Eb

keys. Sold by dozen or hundred.

A26 Flute Trill Key Corks 1/4” (6.4mm)

thick X 13/16” (20.6mm) O.D.

These corks come pre-cut for specific brands

Emerson

A112ETR Trill Key Corks

A112EEF E Flat Key Corks

Gemeinhardt

A112GTR Trill Key Corks

A112GEF E Flat Key Corks

United Musical Instrument

A112UTR Trill Key Corks

A112UEF E Flat Key Corks

Yamaha

A112YTR Trill Key Corks

A112YEF E Flat Key Corks

139

CO

RK

PR

OD

UC

TS

Cork products

A40 SLOTTED TUBE CORKS (Sold by the dozen)

A40 For Conn “Clickless” valves,

1-1/2” (38.1mm) long.

YOU cut to length needed for various models.

FLUTE AND PICCOLO HEAD

CORKS (Sold by the dozen and hundred)

A41 Piccolo 7/8” (20.6mm) Length 7/16” (17.5mm) O.D. 1/8” (3.2mm) Hole

A42 Flute 1-1/4” (31.8mm) Length 11/16” (17.5mm) O.D.

1/8” (3.2mm) Hole

A42A Alto Flute 1-1/4” (31.8mm) Length

1-1/8” (28.6mm) O.D.

1/8” (3.2mm) Hole

STRAIGHT TUBE CORKS (Sold by the dozen or hundred)

A43 Bassoon 1-1/4” (31.8mm) Length

bocal 5/8” (15.9mm) O.D.

3/8” (9.5mm) Hole

A44 Soprano sax, trombone slide bumper

corks 1-1/4” (31.8mm) Length

3/4” (19mm) O.D.

1/2” (12.7mm) Hole

A45 Small Alto sax

1-5/8” (41.3mm) Length

3/4” (19mm) O.D.

3/8” (9.5mm) Hole

A46 Reg. alto sax, C melody, small, tenor

sax 1-3/4” (44.5mm) Length

13/16” (20.6mm) O.D.

9/16” (14.3mm) Hole

A47 Tenor & Bari sax

1-7/8” (47.6mm) Length

7/8” (22.2mm) O.D.

5/8” (15.9mm) Hole

A20 & A21 NEOPRENE BUMPERS

Bumpers are made of

neoprene, preferred by some

players, because it bounces

the valve back faster than

cork.

A20 Neoprene Bumpers-French Horn

A21 Yamaha Neoprene Bumpers for tuba(.175)

Cliff’s Tips……

For trombone slide bumper corks, buy the A44

Straight Tube Corks. Slice a washer off to the correct

length and install on the inner slides. Sometimes a very

tight fit can be eased by cutting the cork ring. The slight

gap that results will not hurt and the slide will push the

ring tightly into place. To remove these corks easily use

the G41A or B Trombone Bumper Remover. Quick,

inexpensive and easy.

TAPERED TUBE CORKS (Sold by the dozen or hundred)

A48 Alto and C Melody Sax,

1-3/4” (44.5mm) long,

3/4” (19mm) O.D.

Hole tapers 1/2”to 5/8”

(12.7mm to 15.9mm)

A49 Tenor and Baritone Sax,

1-3/4” (44.5mm) long,

7/8” (22.2mm) O.D.

Hole tapers 9/16” to 11/16”

(14.3mm to 17.5mm) 140

CO

RK

PR

OD

UC

TS

A65A Asst. of each size including A63

A60A 3/16” (4.8mm)

A61A 1/4” (6.4mm)

A62A 3/64” (1.2mm)

A64A 7/32” (5.6mm)

Cork products

A54 PREMIUM PRECUT

CORK PADS (Sold by dozen or hundred)

Searching for a perfect

portion of sheet cork to make

a cork pad has become

obsolete. Our A54 Premium

Precut Cork Pads have

perfect surfaces on the face of

the pad.

Precut cork pads come from size 6mm thru 17mm

and all half sizes in between. Thickness of the cork

pads are .100” (2.54mm) for sizes 6mm thru 7.5mm

and .110” (2.8mm) for sizes 8mm thru 17mm.

The .100” (2.54mm) thickness is so the cork pad can

be slipped into the pad cup on oboes without

removing the key from the instrument.

Minimum order one dozen per size on sizes 6-13.

A54 Premium Precut Cork Pads,

6-17m in .5 mm steps—Specify Size.

A54A Assortment of 100 Cork Pads

A54-ALL A dozen of each size Cork Pad

from 6 thru 13mm

NATURAL SHEET CORK

High quality 4” (102mm) wide by

12” (408mm) , and sold by the running foot. Best

quality obtainable. High quality!

A63 VERY THIN SHEET CORK This cork consists of 2 very thin layers of cork

which are bonded over a material that discourages

tearing. It is a good product for quality woodwind

repairs. This cork is slightly thinner than our A55

sheet cork or Teflon. It bonds securely to metal

surfaces using our H70 Cork Cement.

Use the A63 for: *Bridge keys and other linkages of all woodwinds

*Key surfaces that are under an adjustment screw.

*Key surfaces that must glide over or under key

arms or spatulas (example: F ring key on all clar-

inets and sax sliders. When used in the appli-

cations above, this cork helps resist ripping,

denting and balling up.

A63 Very Thin Sheet Cork

FITTED MUTE CORKS (Replacements by dozen or hundred)

These composition corks can be used to replace

most mute corks. They are concave on the

bottom for a better fitting surface and glue bond.

Additionally they are rounded on the top for a snug

“ mute to bell” contact area.

A66 Small Mute Cork, 2” X 7/16” X 1/8”

(50.8mm X 11.1 X 3.2mm)

A67 Large Mute Cork, 2-3/8” X 1/2” X 1/8”

(60.3mm X 12.7mm X 3.2mm)

*NEW* “Real Cork”

This natural, compressed cork is great for tenon and

necks, key corks and mute corks. You will find it

very quiet and forgiving. There is NO rubber,

neoprene or vinyl smell to this cork. There is NO

odor!

Great for Rental instruments; as it will recover if

left compressed over the weekend. NOT GASKET

CORK. 4” X 12” sheets.

A55 1/64” (.4mm)

A56 1/32” (.8mm)

A57 1/16” (1.6mm)

A58 3/32” (2.4mm)

A59 1/8” (3.2mm)

A60 3/16” (4.8mm)

A61 1/4” (6.4mm)

A62 3/64” (1.2mm)

A56A 1/32” (.8mm)

A57A 1/16” (1.6mm)

A58A 3/32” (2.4mm)

A59A 1/8” (3.2mm)

Cliff’s Tip….Order yourself a few new D2 knives

because although this sheet cork cuts to a very

nice clean edge it does require a sharp knife.

141

CO

RK

PR

OD

UC

TS

Cork & FELT PRODUCTS

E70 CORK PROTECTOR

Used to place over the end of a sax neck

during the installation of a neck cork using

shellac. Will prevent burning of the cork

while heating the tube.

E70 Cork Protector

P32 OBOE PAD HOLE CUTTER

The P32 set is

designed to cut a

center hole in the A54

Cork Pads when

replacing this type of

pad on oboes. Our set

has two cutters for

cutting the center hole

(One is 4mm the oth-

er is 5.4mm). The

four Brass Centering

dies are recessed on

each end to hold cork pads. Since each centering die

has a different pad size on each end, there are a total

of 8 pad sizes available. They are 9, 9.5, 10, 10.5, 11,

11.5, 12, and 12.5mm.

Also included with our set is a small version of our

P28 Cutting Pad. This should be used under the cork

pad to protect the cutting edges of the hole cutters.

P32 Oboe Cork Pad Hole Cutter Set

D12 CORK STRIP

CUTTING GAUGES

Stainless steel cutting gauges for tenon corks. The

stepped notches on both ends are used for measuring

the width of the cork groove. The other side is a

straight edge.

D12A 4” (102mm) Cork Strip Cutting Gauge

D12B 12” (305mm) Cork Strip Cutting Gauge

F12 CORK STRIPPER Removes old cork

clean and fast from

tenons, mouthpiec-

es, etc… Our cork

stripper is simple

to use. Both ends

will remove the

cork. One end is

8.5mm wide, the

other end measures 9.5mm wide. It is not necessary

to have a complicated and expensive gadget to do

this job. Our hand tool is easy to use and of simple

design. Made of hardened tool steel.

F12 Cork Stripper

WHITE FELT BUMPERS (Sold by the dozen or hundred)

A70 5/16” (7.9mm) O.D.

1/4” (6.4mmm) Thick

A71 3/8” (9.5mm) O.D.

1/4” (6.4mm) Thick

A72 7/16” (11.1mm) O.D.

1/4” (6.4mm) Thick

A73 1/2” (12.7mm) O.D.

1/4” (6.4mm) Thick

A74 9/16’ (14.3mm) O.D.

1/4” (6.4mm) Thick

A75 3/8” (9.5mm) O.D.

3/8” (9.5mm) Thick

A76 7/16” (11.1mm) O.D.

3/8” ( 9.5mm) Thick

A96 Assortment of 100 White Felt Bumpers

A tip that may be useful when installing these

pads in the cup is to leave the cork pad on the

cutter in the chuck of the bench motor. Using 240

grit Emery cloth, taper the sides of the pad before

installation (case not included).

142

CO

RK

& F

EL

T

Item O.D. I.D. Thickness

A80 1/2” (12.7mm) 3/16” (4.8mm) 1/16” (1.6mm)

A81 1/2” (12.7mm) 3/16” (3.8mm) 3/32” (2.4mm)

A82 9/16” (14.3mm) 3/16” (4.8mm) 1/16” (1.6mm)

A83 9/16” (14.3mm) 3/16” (4.8mm) 3/32” (2.4mm)

A84 5/8” (15.9mm) 7/32” (5.6mm) 1/16” (1.6mm)

A85 5/8” (15.9mm) 7/32” (5.6mm) 3/32” (2.4mm)

A86 11/16” (17.5mm) 7/32” (5.6mm) 3/32” (2.4mm)

A88 11/16” (17.5mm) 3/8” (9.5mm) 1/8” (3.2mm)

A89 3/4” (19.0mm) 3/8” (9.5mm) 1/8” (3.2mm)

A90 3/4” (19.0mm) 7/16” (11.1mm) 1/8” (3.2mm)

A91 13/16” (20.6mm) 3/8” (9.5mm) 1/8” (3.2mm)

A92 13/16” (20.6mm) 7/16” (11.1mm) 1/8” (3.2mm)

A93 7/8” (22.2mm) 7/16” (11.1mm) 1/8” (3.2mm)

FELT PRODUCTS

WHITE FELT WASHERS (Sold by the dozen or hundred)

A95 Assortment of 100 White Felt Washers

ELKHART BUNDY/BUESCHER

TOP CAP FELTS FOR CR/TR

These woven felt washers fit all Bundy cornet

and trumpet top valve caps and also can be used

on many other brands. The A99 Bundy top cap

felts measure 11/16” (17.5mm) O.D. X

7/16” (11.1mm) I.D. X .100” (2.54mm) thick.

A99 Bundy Cornet/Trumpet Top Cap Felts

SYNTHETIC FELT SHEETS

BLACK A120-BL .5mm thick (1/64”)

A121-BL .9mm thick (1/32”)

A122-BL 1.2mm thick (3/64”)

A123-BL 1.5mm thick ( 1/16”)

BROWN A120-BR .5mm thick ( 1/64”)

A121-BR .9mm thick ( 1/32”)

A122-BR 1.2mm thick (3/64”)

A123-BR 1.5mm thick (1/16”)

WHITE A120-WH .5mm thick (1/64”)

A121-WH .9mm thick (1/32”)

A122-WH 1.2mm thick ( 3/64”)

A123-WH 1.5mm thick (1/16”)

Many people prefer the performance, feel

and quiet of this felt vs. cork. These felt sheets come in 4” X 12” sheets and

are water repellent. Note, there are 4 different

thicknesses.

WHITE SAX KEY FELTS (Sold by the dozen or hundred)

A77 1/2” (12.7mm) O.D.

1/16” (1.6mm) Thick

A78 9/16” (14.3mm) O.D.

1/16” (1.6mm) Thick

A79 5/8” (15.9mm) O.D.

1/16” (1.6mm) Thick

A97 Assortment of 100 White Sax Key Felts

A19W WHITE FELT SQUARES

A19W 1/16” (1.6mm) thick white felt. For cut

ting Felt washers. 12” square

(305mm sq).

E17 VALVE MIRROR

By using this mirror

you can see if you have

used the proper

thickness valve cork.

This eliminates

“stuffy” blowing in

many instruments.

E17 Valve Mirror

143

FE

LT

PR

OD

UC

TS

This Belt/Disk

Sander is a much

improved version

of our old Z1.

The obvious

improvement is

the addition of an

8” (203mm) disk

sander. This

machine is

ruggedly built

and features tilting tables for both the band sander

and disk sander.

The Z2 does a number of jobs quickly and easily.

For instance, shaping and sanding corks and

stringed instrument bridges, grinding the ends of

newly cut brass tubing , polishing pits out of brass

tubing and a seemingly endless number of other

jobs.

Features include: automatic belt tension, belt

guards, 115 volt 1/3 hp motor, an adjustable arm to

permit the use of belts or different lengths and

adjustable rubber feet.

Z2 Belt/Disk Sander

BUFFING & POLISHING

Ferree’s Industrial quality Belt

Sanders are 16” (406mm) deep

with a 33” (83.8mm) span. Used

primarily for sanding and

polishing brass after dents have

been taken out and to remove

scratches and fine pits before

buffing. Frames are made of

heavy duty square tubular steel

with totally enclosed 3450 rpm

motors. Plenty of room to

maneuver horns. For small

brass, the Z110, 1/3 hp Belt

Sander with 1” (25.4mm) belt

would be satisfactory. If you

work on many larger

instruments, we suggest either

the Z111, 1/2 hp or the Z112, 1

hp. Both use the 1” or

2” (25.4mm or 50.8mm) belts interchangeably. Z111

and Z112 have 2” wide pulleys.

PRICE INCLUDES MOTOR AND THREE BELTS

(Shipped with no switch or plug so you can wire it

for your local electric code).

Z110 1/3 hp, 1” (25.4mm) belt only

Z111 1/2 hp, 2” (50.8mm) belts

Z112 1 hp, 2” (50.8mm) belts

Z113 1 hp, (3 phase) 2” (50.8mm) belts

220 or 440

HEAVY DUTY BELTSANDERS Z2 BELT/DISK SANDER

BELTS FOR Z110 THRU Z113 1” (25.4MM) Belts for all model Belt Sanders.

Z115A 220 grit Z115B 320 grit

Z115C 400 grit

BELTS FOR Z111 THRU Z113

2” (50.8MM) Belts for 1/2” hp Belt Sanders.

Z116A 220 grit Z116B 320 grit

Z116C 400 grit

REPLACEMENT DISKS FOR Z2

These 8” (203mm) sanding disks have self-adhesive

backs.

H125 80 grit disk

H126 120 grit disk

H127 240 grit disk

REPLACEMENT BELTS FOR Z2

Belts measure 1” (25.4mm) wide x 42” (1.07mm)

long.

E62 Extra coarse, 80 grit

E63 Coarse, 120 grit

E64 Medium, 150 grit

E65 Fine, 240 grit

E66 Extra fine

144

BU

FF

ING

& P

OL

ISH

-

www.ferreestools.com We are open Monday-Friday

Buffing & polishing

WALL MOUNT BUFFERS

Our wall mount buffer is good for all buffing

chores, but not for heavy production work as it is

only 1-1/2 h.p. Not for sousaphones and tubas

The shaft is 1-3/8” (34.9mm) in diameter,

ground and polished, stress-proof steel. Total shaft

length is 40” (1.01m) with 5/8”-11 threads.

The shaft extends 12-1/2” (31.75cm) on each

side. The shaft accepts Z56 Buffing Shims that

allow adjusting for various widths of buffs, so the

flange nut is flush with the end of the shaft as

required by OSHA. Provisions are provided to

mount the Z51BS bracket and Z51A Buffing Hood.

The 3/16” (4.8mm) thick steel frame and sheet

metal cover totally enclose the belt and pulleys.

Lifetime lubricated bearings and the heavy duty 1

-1/2 h.p. capacitor motor are included in the price.

Both models are shipped without switch or cord,

as they must be wired to comply with your local

electrical codes. (Can be wired for either 110 or

220 volts)

Z71 1-1/2 hp Single Speed (Is convertible to

variable speed, see note)

Z73 1-1/2 hp Variable Speed.

Truck Ship only. 220 lb. ( 100kb)

VARIABLE vs SINGLE SPEED MODELS

The variable speed buffers are easily adjusted

from 3000 rpm down to 1000 rpm. The advantages

of having a variable speed unit are, the slower

speed that is available for finer color buffing and

the capability of using 10” (254mm) buffs for

economic reasons. The buffer speed can be

increased as the buffs get smaller so you will still

get the same surface feet per minute. A slower

speed for color buffing helps the rouge stay on the

wheel better, making less mess and the buffs don’t

wear out as fast. Color at 2400, hard buff at 2800. See G91R & G91L bushings on page 148.

Ferree’s heavy duty floor model buffers are

designed with a 1/4” (6.4mm) steel housing for extra

strength and rigidity. The shaft is 1-1/2” (38.1mm) in

diameter, ground and polished, stress-proof steel.

This shaft size also helps prevent vibration. Total

shaft length is 54” (1.37m) with 5/8”-11 threads. The

shaft extends 18” (45.7cm) on each side. Floor to the

center of the shaft is 40” (1.02m).

The belt, pulley and motor are totally enclosed for

operator safety. These buffers have provisions for

the Z51BL Buffing Brackets. The shaft accepts Z56

Buff Shims that allow adjusting for various widths of

buffs, so the flange nut is flush with the end of shaft

as required by OSHA. See page 146.

Each model is shipped without switch and cord as

it must be wired to comply with local electrical

codes. The motor is included in the price.

SINGLE SPEED FLOOR MODELS Z100 2hp Single Phase

Z101 3hp Single Phase (Single Speed models are convertible to variable speed)

VARIABLE SPEED FLOOR MODELS Z102 2hp Single Phase

Z103 3hp Single Phase

Z104 3hp Three Phase

Z105 5hp Three Phase

Approximately 450 lbs,. (204kg)

Note on Single Speed Models: The single speed

buffers have one speed, which is 2800 rpm. But, they

can be converted to variable speed by adding a var-

iable speed unit pulley and belt. The conversion price

will be quoted upon request.

Buffing hood & bracket see page 150.

FLOOR MOUNT BUFFERS

145

BU

FF

ING

& P

OL

ISH

-

BUFFING & POLISHING

Z56 SAFETY FLANGE NUTS

Z56 Safety Flange Nuts are used to replace hex

and acorn nuts on buffing machine shafts. The

flanged design provides OSHA safety for the

operator. They are used with the Z55 Spacers to

position the buffing wheels near the end of the

threads.

The Safety Flange Nuts are tightened with a

special spanner wrench. There is less chance for

clothes or aprons to get caught on exposed threads.

The Z56 Safety Flange Nuts are 2” (50.8mm)

O.D. and 3/8” (9.5mm) thick. They are threaded

5/8”-11 (15.9mm-11) for right and left hand

threads. A set comes with a spanner wrench.

IMPORTANT: When installed and spaced

properly, the Z56 Safety Flange Nuts will

completely cover the exposed threads on the shaft.

Z56 Safety Flange Nuts (including wrench)

Z56L Nut-Left Hand Thread

Z56R Nut-Right Hand Thread

Z56W Wrench Only

Z55 SPACERS

The Z55 Buffing Wheel Spacers are used to

position the buffs near the end of the threaded shaft

so the Z56 Flanged Nut will screw on and still cover

the end of the threads. The spacers are 2” (50.8mm)

O.D. and have a 5/8” (15.9mm) hole in the center. A

set contains three different thicknesses of spacers:

3/8”, 5/8” and 7/8” (9.5mm, 15.9mm,& 22.2mm).

Z55 Spacers

G90 TAPERED BUFFER SPINDLES

To hold leather center buffs, Scratch brushes, and

R2 & R3 tapered bell buffs on buffers that use 5/8”-

11 (15.9mm-11) threads.

G90R Right hand thread

G90L Left hand thread

SHAFT UTILITY ARBORS Arbor to hold small

buffs or grinding wheels.

Fits over motor shaft,

affixed by set screw.

Comes in two sizes, in

both right and left hand.

See X116A and B on page

91.

RIGHT HAND ARBOR

D34R 1/2” (12.7mm) shaft size

D36R 5/8” (12.7mm) shaft size

LEFT HAND ARBOR

D34L 1/2” (12.7mm) shaft size

D36L 5/8” (15.9mm) shaft size 146

BU

FF

ING

& P

OL

ISH

-

E7 TAPERED SPINDLES

Mount on motor shaft

for scratch brush or small

buffs. Fit over motor

shaft affixed by set

screw. Comes in two siz-

es, in both right and left

hand.

E7AL 1/2” (12.7mm) left hand thread

E7AR 1/2” (12.7mm) right hand thread

E7BL 5/8” (15.9mm) left hand thread

E7BR 5/8” (15.9mm) right hand thread

COLOR BUFFS

LOOSE MUSLIN BUFFS

Loose buffs with single stitching around hole. Ideal

for buffing with Red Rouge or Nuwhite compound.

1/2” (12.7mm) hole.

R8A 8” (203mm), 1/4” (7mm) thick Muslin Buff

R8B 10” (254mm), 1/4” (7mm) thick Muslin Buff

SINGLE FLANNEL BUFFS

Soft cotton flannel on one side. Single stitching

around the hole. 1/2” (12.7mm) hole. 18 ply.

Softest buff for coloring with red rouge.

R7 8” (203mm), 3/4” (20mm) thick Flannel Buff

R12 10”(254mm), 3/4” (20mm) thick Flannel Buff

Buffing & polishing

TAPERED MUSLIN BUFFS Requires G90 tapered spindles

These buffs are used for

buffing inside horn flares.

R2 2” (50.8mm)

Tapered Buff for

Cornets, etc..

R3 3-1/2” (89mm)

Tapered Buff for

Trombones, etc..

SPIRAL STITCHED MUSLIN BUFF

Usually used in doubles when

“cutting” with Tripoli. Singles

or triples can be used when

needed. Also used with emery.

3/8” (9.5mm) thick with

1/2” (12.7mm) hole.

R9 Muslin Buff,

8”(203mm)dia,

R18 Muslin Buff,

11” (279mm) dia,

4” and 5” CHAMOIS BUFFS

These leather center

chamois buffs can be

used on Ferree’s N99

Bench Motor, using the

E7 tapered spindle, or

on any 1725 rpm

tapered spindle.

Touch up and bring

out the luster of clarinet

and flute keys still

mounted on the body.

Excellent buff to use on better clarinets that do not

have plated keys. Timesaver for flutes that are

demo’s and covered with fingerprints, using, silvo.

Use R49 Key Buffing Compound ONLY with

chamois buffs. These buffs are 12 ply, 3/8” (10mm)

thick.

BR5A 4” (102mm) Chamois Buff, Spiral Sewn

BR5B 5” (127mm) Chamois Buff, Spiral Sewn

BR5C 4”(102mm)Chamois Buff, Center Stitched

BR5D 5”(127mm)Chamois Buff, Center Stitched

147

BU

FF

ING

& P

OL

ISH

-

LEATHER CENTERED BUFFS

RAZOR EDGE BUFF

Very thin, ideal for buffing around clarinet posts.

Eliminates the hazard of tearing posts out of the

body.

R1 4” (102mm) Razor Edge Buff

LEATHER CENTER BUFF For use with your bench motor

This 5/8” (15mm) thick 50 ply buff can be used

with the L8 and E7 tapered spindles and adaptors.

Spiral stitching.

R6 6” (152mm) Leather Center Buff

STANDARD RAGGING TAPE Here’s an answer to the problem of finding a

good cloth for hand ragging. This ragging tape

resists fraying, lasts much longer, and will hold the

rouge. It doesn’t bunch up and makes getting

around valves ports, etc. very easy.

R25 1/2” (12.7mm) wide, 100ft (30.5m) roll

R26 1/2” (12.7mm) wide, 25ft (7.62m) length

R27 3/4” (19mm) wide, 100ft (30.5m) roll

R28 3/4” (19mm) wide, 25ft (7.62m) roll

RU1 GOOD USED MUSLIN BUFFS

Used Muslin Buffs with a 1” center hole. This buff

is similar to our R8A buff, but thinner. These are

good quality buffs. Size varies 7-1/2” thru 8”. See

aluminum G91R and G91L bushings to the right.

RU1 Used Buff

Buffing & polishing

G91 ALUMINUM BUSHINGS To hold buffs with larger holes

These are all aluminum

bushings for 5/8”-11

buffing shaft 1

-1/4” (31.8mm) O.D.

for holding buffs with

larger holes or use

buffs with a larger punched hole.

G91R Right hand thread

G91L Left hand thread

H1 ASSEMBLY GLOVES

Put on a pair of these fine white knit

cotton gloves after buffing and

polishing. When you assemble the

horn you will avoid getting

fingerprints on your freshly polished

metal. One size fits all.

H1 Assembly Gloves

POLISHING WHEEL FOR STEEL 6” (152MM) polishing

wheel for polishing steel.

Has a 1” (25.4mm) center

hole. Please specify

1/2” (12.7mm) or

5/8” (15.9mm) adaptor for

your shaft. Recommended

for removing rust from all

steel mandrels, tools and

parts. Will not distort the

surface. Polishing compound is built into the wheel.

Leaves a fine satin finish. No additional compound is

necessary.

H200 Polishing Wheel for Steel

R22 SPECIAL BUFFING GLOVES

Good quality reversible

buffing gloves with nap

side out. Made of heavy

-duty 10oz. (340g) mate-

rial. Reversible with cen-

tered thumb, so they can

be used on either hand. When worn or dirty, simply

reverse and wear on the opposite hand. Twice the

wear, half the expense. Can also be used while oper-

ating Z60 dent machine.

R22 Pair of Buffing Gloves

ULTRA THIN RAGGING TAPE This thin 3/16” (4.8mm) ragging tape is ideal for

polishing in small areas such as between valve

casing braces and ports.

R30 Ultra Thin Ragging Tape 100ft.

(30.5m) roll

R80 BUFFING RAKE

Keep your buffs in good condition with a Buffing

Rake. These rakes recondition and shape buffs

quickly. They open up the face, eliminate glaze and

prolong the useful life of the buffs. The R80 comes

complete with the rake, but since the rake is easily

replaceable, the handle can be used over and over.

R80 Buff Rake, Complete

R82 Replacement Rake only

148

BU

FF

ING

& P

OL

ISH

-

Buffing & polishing

R49 KEY BUFFING COMPOUND A special shining compound to be used with

BR5A and BR5B chamois buffs. Used to polish

nickel clarinet and flute keys still mounted on the

body. White color. 1 lb. 14 oz. (.85 kg).

R49 Key Buffing Compound

SUGGESTED BUFFING

PROCEDURE Following is a procedure which we have found to

be safe and reliable. This procedure is used:

AFTER THE HORN HAS BEEN REPAIRED

AND BRITE DIPPED.

Experienced Repairmen may have other methods or

be able to skip certain steps, but the techniques detailed

below will always work and the buffing compounds used

are the same.

STEP 1A This step can be omitted on normal jobs

EMERY

For use on a horn which had a

sand blasted, silver plated finish.

After stripping, use a R9 Spiral

Stitch Buff and Emery Cake to

smooth the sandblasted surface in

preparation for buffing (weight~ 3 lbs.-1.4 kg each).

R45A Emery Cake, Single

R45B Emery Cake, Dozen

STEP 1B TRIPOLI

This is a hard buffing and cutting compound. Used

after Step 1A or in place of Step 1A on normal

relaquering jobs. Use a R9 or R18 Muslin Buffs. You

almost NEVER use a single section. Running 2

prevents flopping, which dents (weight~3 lbs.-1.4 kg).

R46A Tripoli Cake, Single

R46B Tripoli Cake, Dozen

STEP 2 May be omitted by some buffers

NUWHITE

Sometimes used after

Tripoli operation. Works

best on white brass,

commonly called,

“nickel” (3 lbs-1.4 kg).

R47A Nuwhite Cake, Single

R47B Nuwhite Cake, Dozen

STEP 3

RED ROUGE Color buffing is the final process and the most

important one for a professional job. It brings out the

finest, richest color of the brass and removes minute

scratches. Use R7, R12 or

R8A, R8B for coloring.

Some prefer muslin color

buffs, some prefer flannel

color buffs. It is personal,

depending on the finish

wanted. Red also works on

smooth silver plate (weight~3 lbs-1.4 kg).

R48A Red Rouge Cake, Single

R48B Red Rouge Cake, Dozen

STEP 4 Following the red rouge buffing, the horn should

be thoroughly degreased. The best way to degrease a

horn is with a hot vapor spray degreaser. This is the

fastest, most complete method of removing buffing

residue from a horn. Removing this residue is very

important, because lacquer WILL NOT STICK to a

greasy surface.

After completing the necessary steps listed above,

the horn is ready to be assembled and lacquered. Use

a clean pair of H1 Assembly Gloves to avoid finger

prints when handling the horn.

149

BU

FF

ING

& P

OL

ISH

-

Notes from customers: “Want to thank you once again. The last

session was as fantastic as the pervious ones!

It’s amazing how much I learned within just

one day!”...Dennis, Canada

BUFFING & POLISHING

Z46 COLLECTION BAG TYPE

BLOWER UNIT

For buffing room exhaust systems. Used

where collection bags are necessary or with

permanent collection box. Sturdy welded 16 gal.

steel housings. Balanced self-paddle-type wheels.

With or without a motor.

DIMENSIONS Wheel diameter 10-5/8” (270mm)

Motor: 1 h.p.

Wheel bore 3/4” (19mm)

Inlet 6” (152mm)

Outlet 4”(H) x 3-1/2” (W) (102mm high x 89mm

wide)

Overall 18” x 21” x 16”(457 x 533 x 406mm)

Z46 Complete Blower with Motor,

1hp 3450 rpm, 115/220v,

single phase

Z58 COLLECTION ASSEMBLY Adaptor pipe and bag to attach at discharge

opening for collection.

Z58 Collection Assembly complete

Z58B Bag only

150

Z51 BUFFING HOOD

Our Z51A Buffing Hood is

made from heavy, galvanized

steel and has an adjustable

wheel opening. It can be set on

your base or on the Z51B

Folding Bracket. By using the

bracket, you can move the

hood back when buffing larger

instruments.

Z51A Buffing Hood Only

Z51BS 11-1/2” Bracket for wall mounted buffer

Z51BL 17-1/2” Bracket for floor mounted buffer

INSTALLATION ACCESSORIES

Z52 4” (102mm) Flexible Tubing

Z54 6” (152mm) Y tube, two 4” (102mm) inlets

www.ferreestools.com

BU

FF

ING

& P

OL

ISH

-

Z35 PORTABLE AIR BUFFER

This portable air

operated buffer is

handy for cutting

down “make ready”

time on brass

overhauls. It has a

special spindle for

small buffs for those

hard-to-reach solder spots and marks. No more

scraping. Terrific on large instrument overhauls

such as French Horns, Baritones or Sousaphones.

Used in many instrument factories. Very practical if

you do much brass overhauling. Hooked to your air

compressor, this tiny high speed buffer goes 16,000

rpm with 1/3 hp capacity.

Watch the solder disappear. A 2” (50.8mm) buff at

this speed gives 8350 surface feet (2545 surface

meters) per minute. Compare this to an 8” (203mm)

butt at 2800 rpm which gives only 5850 surface feet

(1783 surface meters) per minute. This tool has a

handy lever control and a built in hang up hook.

Requires 4 cu. ft. (113.3 cu. L.) of air per minute at

90 to 100 lb (6.3 to 7 kg/cm²) pressure. Price

includes four R10 buffs.

Z35 Portable Air Buffer

R10 Extra 2” (50.8mm) Buff

Z35S Shaft only

Notes from customers: “Thanks for the wonderful notes...they are

gold!”...Joe

Z97 SCRATCH BUFFING

MACHINES

The Z97 Scratch brush machine includes a mount-

ed 1/4 hp totally enclosed motor. This machine

incorporates a permanent tapered spindle, plastic

covering and is available either right or left handed

to fit the area of use.

Z97L Left handed scratch buff machine

with motor

Z97R Right handed scratch buff machine

with motor

BUFFING & POLISHING

SCRATCH BRUSHES

Used to clean satin finish, silver plated

instruments with soap bark and water. If

necessary, boil out the instrument in Z15

Combination Lacquer Strip and Silver Clean

Solution, followed by a clear water rinse. Drip

“a detergent solution” on the brush while using,

to keep it wet during the scratch brushing pro-

cess. All brushes are of crimped brass wire.

GOBLET

H5 2” (50.8mm) 6 row for cornet

H7 3” (76mm) 8 row for trombone

Both goblets have .004” wire

ROUND

H11 4” (102mm) 2 row, .0035”, 1-1/2” hub

H12 4” (102mm) 2 row, .005”, 1-1/2” hub

H13 6” (152mm) 2 row, .0035”, 2” hub

H14 6” (152mm) 2 row, .005”, 2” hub

CYLINDRICAL

H3 4” (102mm) X 3/4” (19mm)

Cylindrical scratch brush

H4 5” (127mm) x 1-1/4” (31.8mm)

Hand held have wooden handles

151

BU

FF

ING

& P

OL

ISH

-

Ferree’s Tools, Inc

Early 1960’s

Providing quality service since 1946. Place

your order today and we will get it out in an

efficient and timely manner. You can now

order by email for more convenience.

[email protected].

N54 Knuckle Tools

N54A (5) Knuckle Tools

N55 Knuckle Tools

N55E (2) Knuckle Tools

N31/A/B Dent Rods

N69/N74 Dent Rods

N32/N33 Dent Rods

N34 Dent Rod

N56 Mouthpipe Cable Kit

N17 Bassoon Bocal Cable

P50 Trpt Dent Ball Driver

P58 Sax Neck Dr/Retriever

P56 Fr Horn Bell Driver

P52 Dent Ball Hammer

P53 Trmb. Dent Ball Retr.

P54 Trombone Hammer

F11/11A Canvas Hammers

F10S Set, Steel Dent Hammers

F9 Brass Hammer

N68 Right Angle Mandrel

E17 Valve Mirror

N1/2/3 Burnisher

N2A (3) Handles

N15 Shank Truing Tool

L3/L4 Bell Irons

L13 Tuning SL Removal TL

N4 Yamaha Tool

L17/L18 Burnishing Rings

L19 Handle

F5/5A/5B Leather Hammers

N14A/B Mandrels

N51S Mouthpiece Arbors

N58’s Ground Casing Mandrels

N28’s Ground Sleeve Mandrels

G45A/B Cork Barrel Tools

P102 Yamaha Thread Tool

G35 Spacers

N87A Trombone Pliers

N53A #4,5 Trb. Slide Mandrels

N53B #6,7,8,9,10 Mandrels

N52A/C Slide Mandrels

N35/36/37 Right Angle Expanders

N91S Set, Tapered Mandrels

N90 Tapered Mandrel

N93 Sax Body Rod

P60 Rotary Valve Tool

P60C #5,6,7 Collets

P90/P91 Trb. Stone/Stand

G41A/B Trb. Bumper Removers

Z6/Z8/T85 Lubricants

E15D Bench Plier

D44 Pin Vise

L20 Bench Block

G23 Bench Oiler

S70S (2) Cleaning Rod

S71 (2) Cleaning Rod

S80-S96 (1dz of ea) Valve Springs

S90-S93B (1dz of ea) Waterkey Springs

D49 Waterkey Installing Jig

A14/A15 (1c of ea) Cork Washers

A16/A17 (4dz of ea) Cork Washers

A1/A2 (1c of ea) Cork Washers

A3/A4 (4dz of ea) Cork Washers

A27 (4dz) Straight Waterkey Corks

A28 (2c) Straight Waterkey Corks

A29 (4dz) Straight Waterkey Corks

A33 (4dz) Tapered Waterkey Corks

A34 (2c) Tapered Waterkey Corks



A18A-D (1dz of ea) Fr Horn Corks

A80 (2c) Felt Washers

A84 (1c) Felt Washers

A90 (1c) Trombone Felts



A99 (2c) Trumpet Felts

N75 Flute Head Mandrel

N76 Flute Body Mandrel

H65 Piccolo Head Mandrel

H66 Piccolo Body Mandrel

N16S Set, Dent Rod Guides

O70S Set, Wood Mandrels

O70D Wood Mandrel

N72 Sax Body Bow Rod

N73 Sax Neck Rod

N80AS (2) Dent Ball Set

N80BS Dent Ball Set

N80CS Dent Ball Set

N80DS Dent Ball Set

N80ES Dent Ball Set

N57G 101 Dent Ball Set

N57X 4 Barrel Dent Balls

N82 Dent Ball Holder For N80’s

N59 Magnet Locator

N81S Slotted Sax Dent Balls

N65S Barrel Ball Set, Rod Mounted

N70 French Horn Rod

N71 French Horn Rod

Z10B Cold Cleaner

F7B Brasso, Gallon

J88A “Cracker” Oil

L54 Torch Kit

F33 Soldering Torch

E40 (2) Triangular Scraper

F13 Solder Scraper

F14 Solder Scraper

F15 Solder Scraper

F31B Cutting Pad

F41 Soft Solder Flux

F42 Solder Solder

F46B Flux, Quart

F49 Tix Anti-Flux

F32 Striker

J45 12 x 12 Millboard

N13 Bell Mounting Jig

N19 Large Solder Clamp

N66A Mthpiece Rec Reamer-Cor

N66B Mthpiece Rec Reamer-Trpt

N66C Mthpiece Rec Reamer-Tb/Br

D33 Bench Knife

H114 220 Emery Cloth Roll



E29A Fine Narrow File

F57 Side Cutters

G62 Metal Back Saw

G97 6” Ruler

G24A 6” Dial Caliper

L14A V-Block

L22 Lead Jaws

E90 Cor/Trpt Slide Pliers

E92 Baritone Tuning Slide Pliers

E94 Sousa/Tuba Pliers

G18 Pad Gauge

G16 Sm. Center Punch

G16A Med. Center Punch

F48 Utility Pliers

F61B Parallel Jaw, Scored Plier

X21 Cabinet For Corks/Felts

Z30 Tool Chest

H70 Cork Cement

H70S Solvent

H72 Extra Can

F72 Large Screwdriver

F67 Medium Screwdriver

J20SS Round Nose Plier

J22SS Small Duckbill Pliers

Suggested brasswind bench

152

BR

AS

SW

IND

BE

NC

H

Here is the list of tools by Gary Ferree, for a brasswind bench; for most repairing less

than overhauls. I have listed everything as a one of, to make it simple. These are hand

tools, the Z60 dent machine and related accessories are treated separately (pg. 96).

153

Lacquering & cleaning equip.

SILVER STRIP FORMULA Add 4 oz (113.4 gr) salt peter (potassium

nitrate) to each gallon (3.79 L) of sulphuric acid.

Needs to be stored in the plastic lined barrel.

This is used to remove silver plate from silver

plated instruments. You will then be down to the

original brass finish. Now the instrument may

be buffed and lacquered. Be careful not to leave

it in the solution too long or it will become

pitted.

WOOD LACQUERING MANDRELS

Used to hold an

instrument during

lacquering with less

chance of dropping the

instrument.

Also, handy for storing

instruments in the lacquer

room between coats.

O4 For cornet or trumpet

O5 For trombone

(Saxophones and larger instruments should

be hung instead of held.)

Z27 PLASTIC FLUTE TRAY

This deep tray will accommodate most flute

bodies and parts for dipping in Z25 Tarnish

Remover. It measures 15” X 6” X 2” (381mm

x 76mm x 50.8mm).

Z27 Plastic Flute Tray

Z19 LIME AND SCALE REMOVER Z19 Lime and Scale Remover was designed to

completely replace acid based materials in lime and

scale removal. Deposits are removed rapidly and

effectively with a minimal attack on brass, copper,

aluminum, etc.. Great for slides and valves that are

corroded with lime. Shipped in crystal form, just

add water. Mix is 1 lb (.45 kg) to 1 gallon (3.79

liters) of water. 9 lbs or less NO hazard fee.

Z19A Lime and Scale Remover, 1 lb (454 g)

Z19B Lime and Scale Remover, 10 lb (4.5kg)

Z19C Lime and Scale Remover, 25 lb (11.3kg)

X68 WORK BASKET

It will be useful in many dipping

type operations. Lighter gauge,

with a 14-1/2” (368mm) handle, it

has a wooden bar to hold so it

doesn't get too hot. 9-3/4” OD X

6” Deep.

X68 Work Basket

(Aluminum)

154

J85 RUST INHIBITOR

Keeps your tools rust free.

Fortified lanolin absorbs up to

five times its own weight in

water. Sets up a protective

barrier film to provide lasting

rust protection. It is a natural

lubricant. Spray on tools or

machined surfaces. Lubricants

can be applied over J85 Rust

Inhibitor without reducing their effectiveness. If

removal is desired, use Z10 Cold Cleaner.

J85 Rust Inhibitor 11 oz (312 g)

LA

CQ

. &

CL

EA

NIN

G

FEEL FREE TO CALL 800-253-2261,

24 HOURS A DAY TO PLACE

YOUR ORDER.

FAX YOUR ORDER TO

269-965-7719

EMAIL ORDERS TO

[email protected]

X52 COTTON CLEANING PADS These new cotton pads are 4” X 4” and are great

for cleaning or any personal need you may think of.

X52 Package of 100 Cleaning Pads

Lacquering & cleaning

WENOL POLISH

For use on the outside surface of instruments.

Excellent for gold, silver, brass and copper.

No grit. Quickly removes oxidation, tarnish,

paint and most stains.

J31 Wenol Polish 100 ml tube

Z25 TARNISH REMOVER Cleans flute bodies like magic

Tarnish Remover is the best silver cleaning agent

on the market today. It can penetrate and clean the

darkest tarnish off all silver plated items in seconds.

It is exceptionally useful when cleaning flute bodies

in the areas of post rib construction and rolled tone

holes. Size is not a factor. Tarnish Remover can do

the job on anything from a tuba to a flute body.

Please note that a PLASTIC container MUST be

used to store TARNISH REMOVER.

Z25A 1 qt (.95 L) Tarnish Remover

Z25B 1 gal (3.79 L) Tarnish Remover

155

LA

CQ

. & C

LE

AN

ING

Z40 SAND BLASTER

For sand blasting

instruments or

parts before

plating. The new

model F “Sandy

Jet” siphon sand

blaster is equal in

performance and power to equipment many times

larger. The user serviceable pistol grip type blast

gun connected to the sand and air hose, is the only

weight you hold.

OPERATING AIR PRESSURE Volume of air required at 80 lbs. (5.5kg/cm2) is:

7cu.ft./min. with 13/64” nozzle & 5/64” airjet;

15cu.ft./min. with 1/4” nozzle & 1/8” airjet; 20

cu.ft./min. with 5/16” nozzle & 5/32” airjet.

Regardless of the nozzle/jet used, the amount of air

that is used is very conservative. Airjet and nozzle

must be paired correctly for best results. The outfit

consists of: Power gun, container of 50lbs (22.7kkg)

of sand, which is 10qts. (9.5L, 7ft {2.13m}) of hose

connecting the gun to the sand container. Operator’s

face shield and hood, nozzles, airjets, Allen wrench.

Z40 Sand Blasting Outfit

Z42A Air Jet 1/8”

Z42S Sand Nozzle 1/4”

Z43A Air Jet 5/32”

Z43S Sand Nozzle 516”

Feel free to call for current

pricing on items or go to

www.ferreestools.com for updated

price lists.

Call 24 hours a day to place

your order!!

800-253-2261 One of Ferree’s early locations in

Battle Creek, MI

X50 CHEESECLOTH Cheesecloth is the best and most economical

material there is for cleaning valve casings and

trombone slides. A continuous piece of cloth is very

useful for a brass technician because of the different

lengths needed for cleaning trombone slides and

valve casings. Dirty cloth can be snipped off and

clean cloth can be rethreaded through the cleaning

rod quickly for the next cleaning operation. This box

of continuous cheesecloth will eliminate waste and

save money.

X50 Cheesecloth. Full box of 80 yds

(3.15m)

X51 Cheesecloth. Specify yards wanted

X56 COTTON FLANNEL This cotton flannel has nap on both sides of the

cloth and is woven to be extra soft. This is the type

of cloth used to wipe spots off brass instruments

after degreasing and prior to lacquering. Some pol-

yester types of cloth will scratch the brass. With

this flannel you will never have that problem.

Excellent for color ragging with R48 Red Rouge.

Works great when using Silvo or Wenol polishes.

X55 Cotton flannel by the bolt of 50 yds

(45.72m) by 27” (68.6cm)

X56 Cotton flannel, specify the yards

wanted

Brite Boy Excellent silver cleaner and polish. For silver,

brass, copper, chrome, stainless steel and

aluminum.

F4 8 oz (236 ml) can Discontinued, See T71

BRASSO Best polish made for hand polishing brass.

Very easy to use. Excellent for cleaning and

polishing trombone slides and valve casings.

F7A 8 oz (236 ml) can

F7B 1 gal (3.79 L)

F7C Quart

J34 RED BEAR

Similar to Brasso, but has no grit and is water

soluble. Good for trombone and cornet slides.

J34 Red Bear Polish 180 gram can


TARNI-SHIELD

3M Tarni-Shield is

available in Silver or

Copper/Brass clean-

er. Besides cleaning

and polishing your

copper and brass

beautifully, these

cleaners contain

an anti-tarnish protector that helps keep your fine

silver or copper and brass pieces tarnish free.

T71 3M Silver Cleaner 10 oz (296 ml)

T72 Copper & Brass Cleaner 10 oz

(296 ml)

156

SILVERSMITH’S

POLISH AND SPRAY

Great for making instruments shine like new.

T73 12 oz Silversmith’s Polish

T74 14.5 oz Silversmith’s Spray

LA

CQ

. &

CL

EA

NIN

G

O6 TUBING CLEANER BALLS

Brushes are fine for cleaning the inside of

brass tubing, but getting material out of the

bottom bow in a trombone slide or other curved

tubing is another thing. A brush with bristles

stiff enough to remove the stubborn deposits

probably wouldn’t make the curve without

putting scratches in the bore. Here’s a better

way.

Put a small quantity of these O6 Tubing

Cleaner Balls inside dirty tubing. Add some

lukewarm, detergent water and shake.

You may have to repeat this process a few

times, to get the tubing thoroughly cleaned.

The balls can be reused many times.

We’ve put 600 of these brass balls in a handy plastic storage bottle. We think you’ll be

pleased with the job they do.

O6 Tubing Cleaner Balls

**New item number** (old number was P1)

CYLINDRICAL TANKS-

BARREL LINERS

Both the 30 and 55 gallon sizes of these barrel

liners have a cuff type flange to cover the barrel

edge. NOTE: NOT self-standing! MUST be used

inside the correct sized steel barrel for support.

Will hold your Silver Strip or Z21 Cold Strip when

properly installed inside the correct steel barrel. The

5 and 10 gallon sizes will stand alone when used with

thinner such as Cyanide and Brite Dip. Price Includes

cover.

Cap

Gals.

Outside

Dia. In.

Flange

Dia. In.

Overall

Dpth.

In.

X32 5 11 12-3/8 15-1/8

X33 10 13-3/8 14-3/4 20-3/8

X30 30 17-13/16 19-1/2 28-1/4

X31 55 22 23-11/16 34-1/2

Cap.

Liters

Outside

Dia.

Cm.

Flange

Dia.

Cm.

Overall

Dpth.

Cm.

X32 18.9 27.9 31.4 38.4

X33 37.9 34.0 37.5 51.8

X30 113.6 45.2 49.5 71.8

X31 208.2 55.9 60.2 87.6


157

LA

CQ

. & C

LE

AN

ING

COMBINATION LACQUER REMOVER

AND SILVER CLEANING SOLUTION

This product will

effectively remove most

cellulose lacquer. Mix

1/2 lb (.226 kg) per 1

gallon (3.79 L) of water.

Use at 180° to 210° F

(82.2° to 98.9° C). Will

also remove old orange

King lacquer. Removes most oridnary lacquer in 10

minutes. Safe on all metals EXCEPT Aluminum

(Hazardous. Can ship by UPS Ground ONLY).

Z15A 10 lbs (4.5 kg)

Z15B 25 LBS (11.3 kg)

World’s Largest Manufacturer of

Quality Band Instrument

Repair Tools.


Lacquering & cleaning

SUGGESTED LACQUER

ROOM LAYOUT

The drawing above is a suggested lacquer

room layout. We have used the basic design as

described below several times in different

buildings. The overall space needed is about 10

ft. (3 meters) by 12 ft. (3.66 meters) OR about 6

ft. (1.8 meters) by 20 ft. (6 meters) if you put

the above drawing in halves, end to end. The

lacquer room must be basically, air tight. The

exhaust fan MUST be on an outside wall. You

can mount air filters over, beside, or in the door

to draw fresh, warm, dry air into the room and

filter out the dust and lint at the same time. IF

you can, you may mount the filters in the

ceiling, where they are NOT in the booth.

The room is divided by a wall that extends

two-thirds of the way across the room. This

wall confines the spray to a small area. On the

other side of the divider, put racks to hold our

O4 thru O5 lacquer mandrels. Place instruments

on these mandrels after spraying or while

waiting to be sprayed. With either layout, you

don’t have to open and shut the door during

spraying time. This avoids raising a lot of dust

and lint. The baffle on the spraying side is

important because it creates a venturi effect.

NOTE: All lacquer, Thinner, Retarder, and Dye

MUST, by law, ONLY be shipped by UPS Ground

or Truck….They are Considered Hazardous. We

are NOT able to ship these items Overseas due to

Regulations. Can ship to Canada by UPS ONLY!

X70 FERREE’S CLEAR LACQUER An excellent quality cellulose lacquer. The same

lacquer used by many band instrument man-

ufacturers on instruments too large to use bake-on

type epoxy lacquer. Excellent color retention,

better perspiration resistance and surface hardness

than older types of lacquer. Use on brass, nickel and

silver. We do NOT recommend buying larger than

gallon lots of lacquer, unless you have a very large

volume of work. Should be used up within 6-8

months for best results.

X70A 1 qt. (.95 L) Clear Lacquer

X70B 1 gal. (3.79 L) Clear Lacquer

X70C 5 gal. (18.9 L) Clear Lacquer

X71 FERREE’S THINNER (Used with X70 Lacquer)

X71A 1 qt. (.95 L) Thinner

X71B 1 gal. (3.79 L) Thinner

X71C 5 gal. (18.9 L) Thinner

X72 FERREE’S RETARDER To be used when the humidity is between 50% to

90% (if higher, wait until another day to lacquer).

This retarder will slow the drying action to prevent

blushing (whitening) of lacquer.

X72A 1 qt. (.95 L) Retarder

X72B 1 gal. (3.79 L) Retarder

FERREE’S SPECIAL GOLD DYE

No more light and dark dyes

needed, this new concentrate is all

you will need. This 2 ounce

concentrate is available in place of

the light and dark dyes that are

now discontinued.

X73 Dye Concentrate

IMPORTANT!

Call your local environmental

agency before disposing of any

chemicals.

158

LA

CQ

. &

CL

EA

NIN

G

Q1 NIKOLAS CLEAR &

Q1G GOLD SPRAY LACQUER

Don’t dirty up your

spray gun for those

little touch up and spot

lacquering jobs.

Ferree’s carries the

solution: Q1 Nikolas

Clear and Q1G Gold

tint spray lacquers in

pressurized cans.

Q1 Clear Spray Lacquer 12 oz

Q1G Gold Spray Lacquer 12 oz

LACQUERING & CLEANING EQUIP.

X26 EXPLOSION PROOF

EXHAUST FAN

The X26 exhaust fan

is designed especial-

ly for the removal of

lacquer fumes from

spray booths. The

unit features a

16” (40.6cm)

fan with a 1/4 hp totally enclosed motor. Cast

aluminum fan blades. Won’t make static sparks.

Unit is complete with shutter. Class 1, Group D,

explosion proof motor.

X26 Exhaust Fan (110V or 220V)

HOSE AND FITTINGS Hose, 1/4” (6.4mm) ID, 1/2” (12.7mm) O.D. for

use between spray guns and the F29 air transformer

and pressure regulator.

F30 Hose, sold by the foot

E6 Female hose connection

E48 1/2” (12.7mm) air valve for

controlling air lines. Leak proof.

X27 DEVILBISS SAFETY LIGHT This safety light is a

vapor proof

incandescent light

fixture that provides

economical, safe

illumination for all

spray booths.

Porcelain enamel

reflectors. Sealed

glass globes for safety and easy cleaning. 200 watt.

X27 With 1/2” (12.7mm) conduit bracket

(110V)

F1 RECOILING AIR HOSE

Non-kinking**No age deterioration**Oil resisting

Micro-finish**Light Weight**Compact Storage

Spray guns, air dusting guns, grinding and

polishing tools. This permanently coiled nylon hose

with reusable connections keeps the hose off the

floor and out of the way when not in use. 1/4” I.D.

and 25 feet (7.6mm) long and recoils to about

8” (203mm). Ends are 1/4” NPS(M).

F1 25 ft (7.6mm) Recoiling Air Hose

E35 QUICK DETACHABLE AIR

CONNECTIONS

Fast, twist lock air

connections for all types of

spray guns. Save time, mon-

ey and hose. Positive lock,

no leaks, light-

weight, reusable. For

1/4” (6.4mm) inside

diameter hose.

E35B Quick connection stem—female

E35C Quick connection stem—male

B

C

159

LA

CQ

. & C

LE

AN

ING

CALL 800-253-2261

TO PLACE YOUR ORDER

FERREE’S COLD STRIP

BRUSH ON or IMMERSION A special lacquer stripping solution used cold.

Removes cellulose lacquers and most epoxy

type lacquers. Many dealers like it because of

the “no heating” feature. It comes in two types.

Order Z22 for brush on use or Z21 for tank use

( immersion ). Must be used in plastic tank.

Z21A 5 gal ( 18.9L) Immersion type cold

strip—Hazard fee

Z21B 15 gal (57L) Immersion type cold

strip—Hazard fee

Z22A 1 pt (473ML) Brush on cold strip

Z22B 1 qt (.95L) Brush on cold strip

Z22C 1 gal (3.79L) Brush on cold strip

Z10 FERREE’S COLD CLEANER

NOT a degreaser, but, it is a VERY GOOD cold cleaner. It is useful for wiping valves, casings, and trombone

hand slide after they have been cleaned with F7 Brasso. It is very important to wipe

out valves and slides with the Z10 Cold Cleaner to be sure

any abrasive is removed.

Z10A 1 qt (.95L)

Z10B 1 gal ( 3.79L)

Z10C 5 gal (18.9L)

F35 DEVILBISS

SPRAY GUN AND PRECISION

GUN ATTACHMENTS

LIKELY OUR MOST POPULAR SPRAY GUN

with extreme accuracy, delicate controls and ease of

handling. This gun is excellent for spot lacquering

and all band instrument spraying except

sousaphones. Running is practically eliminated if

lacquer mixture is anywhere near correct. Cup

attachment and cups must be ordered separately.

F35 Devilbiss Precision Spray Gun

F36 Cup Attachment for F35 Gun

F37 Cup for F35

F38 LARGE PRECISION GUN

A PRECISION SPRAY GUN...but, with larger

capacity and larger spray pattern than the smaller

version above. Feather weight and precision built

to handle all band instruments including

sousaphones. Cup attachment and cups must be

ordered separately.

F38 Large Spray Gun

F39 Cup attachment for F38 Gun

F40 Cup for F38

Both of the above guns have a built-in air gun

feature to blow dust and lint off horns just before

spraying.


160

LA

CQ

. &

CL

EA

NIN

G

See new items and repair tips on

our website


F43 DUST GUN

This is an OSHA approved model dust gun. These

guns are very useful. Blow out cases, clean benches

and other places where a dust brush cannot reach.

F43 Dust Gun

F43A Coupling to attach F43 Gun to air

hose

CLIFF’S TIPS… Always use 1/2” (12.7mm) galvanized pipe

between your air compressor tank and your air

compressor regulator to cut down resistance. The

same type of pipe should also be used between the

compressor and the air regulator for a torch.

Lacquering & cleaninG

Here is a lacquer mixture we have used

successfully for over 50 years.

FIRST TWO COATS

2 qts. (1.9 L) X70 Lacquer

1-1/2 qts (1.42 L) X71 Thinner

1 pt (473 ml) X72 Retarder

Add gold color if desired

THIRD “BRIGHT” COAT

Take equal parts; one of the above mixture and

one of the thinner and mix them together.

FERREE’S PERMA-LAQ AN EPOXY TYPE LACQUER

Ferree’s Perma-Laq is an epoxy modified lacquer

developed for use where chemical and abrasion

resistance as well as clearness are primary

requirements. This is the same lacquer used by

many of the band instrument manufacturers.

Perma-Laq can be used in any repair shop, small

or large. It can be sprayed with the same gun, at the

same pressure, used for the regular cellulose

lacquer. No additional lacquering equipment is

needed. Remember, clean gun after every use.

Perma-Laq is premixed epoxy lacquer.

Recommended mixture is: add 5% catalyst and 5

-10% reducer to the Perma-Laq. Reducer needs vary

according to local humidity. After lacquering the

horn, bake it at 200-250 degrees F (93.3°-121.1°C)

for 20 minutes. BAKING IS MANDATORY.

ONE COAT APPLICATION ADVANTAGES

OUT-WEIGH THE HIGHER PRICE

Perma-Laq is more expensive, but requires only

one coat. This saves on both time and material and

cuts down the possibility of spraying errors. This

system eliminates time in the lacquering room.

*TRANSFER TO GLASS CONTAINER WHEN

YOU RECEIVE*

X80A 1 qt. (.95L) Perma-Laq

X80B 1 gal. (3.79 L) Perma-Laq

X80C 5 gal. (18.9 L) Perma-Laq

X81A 1 qt. (.95 L) Perma-Laq Reducer

X81B 1 gal. (3.79 L) Perma-Laq Reducer

X81C 5 gal. (18.9 L) Perma-Laq Reducer

X82A 4 oz (118 ml) Perma-Laq Dye

X82B 1 pt (473 ml) Perma-Laq Dye

X83A 1 pt (473 ml) Perma-Laq Catalyst

X83B 1 qt. (.95 L) Perma-Laq Catalyst

Don’t have an oven to bake Perma-Laq?

An old refrigerator with metal insides and

a hook installed through the top makes a

good oven. 3-275 watt infrared bulbs

inside will provide all the heat you need to

bake the lacquer. Set an oven candy

thermometer inside the box or through the

door to be sure.

Like all epoxies, Perma-Laq has a 8

-10 months “pot life”, if properly stored

We don’t package it until the order is

received. Transfer it to a glass container as

soon as you receive it. Store it at room

temperature out of direct sunlight. Using

these precautions, you may extend the shelf

life as long as one year. Don’t order more

than you can use in 6 months.

CLIFF’S TIPS...

Most chemicals cannot ship by

air. We can ship them by UPS

ground only.

Lacquer, etc. cannot be shipped

overseas.

161

LA

CQ

. & C

LE

AN

ING


SOLDERING

*NEW* L53 EXCALIBUR

SOLDERING KIT

Self igniting cordless soldering iron. Hot air

blower and torch kit.

Includes a wide range of tips. Ideal for au-

tomotive, industrial, electronic system repair,

woodworking, general maintenance and

professional repair jobs.

L53 Excalibur Soldering Iron Kit

L54 TORCH KIT

This L54 torch kit is

used with a “B” tank,

which you must purchase

locally. This type of torch

set has been used for over

50 years and is time test-

ed and proven to be very

dependable.

Has 12-1/2” ft. hose.

L54 Torch Kit

L54-1 Tip

”B” TANKS MUST BE PURCHASED

LOCALLY**

*NEW* L63 PENCIL TORCH

This little torch gives you the same flexibility you

had with a blowpipe. A hotter flame than the Butane

bunsens, good for use on saxes with nickel plated

keys. Uses butane.

L63 Pencil Torch (uses butane)

162

SO

LD

ER

ING

*NEW* L1 BERNZ-O-MATIC

TORCH

This kit includes: burner wand, hose, oxygen

regulator, fuel gas valve, cylinder stand, MG9 16 oz

MAPP Gas Cylinder, OX9 1.1 cubic foot oxygen

cylinder, spark lighter, 5 brazing/welding rods.

**Solid brass regulators for durability.

**Adjustable flame for a wide variety of applications

**Metal stand provides increased cylinder stability

for ease of use.

**Applications include: silver soldering, brazing;

cutting bolts up to 5/8” diameter; cuts light weight

steel and sheet metal; welds up to 3/16” steel.

L1 Bernz-O-Matic Torch Refills must be purchased locally.

**Hazardous** Extra shipping costs may apply.

Most items are in stock for quick

delivery!!

We accept Visa, Master Card &

Discover

TRIANGULAR SCRAPERS

Triangular Scrapers are used for scraping and

cleaning solder from inside of tubing, for trimming

tight tenon joints and many other general uses,

including use as a fine lathe cut-off tool.

E38 Solid sides, straight edges

E40 Hollowed sides, straight edges

SOLDERING

SCRAPERS

HALF ROUND SCRAPER

Half round scraper is used to remove solder from

inside of tubing. About 8” (203mm) long including

the handle.

F16 Half Round Scraper

F13 Curved Solder Scraper-Narrow

F14 Curved Solder Scraper-Medium

F15 Curved Solder Scraper-Large

G43 FERREE’S SOLDERING JIG

This is a high strength, industrial quality, heavy

duty soldering jig. It features full steel construction

for durability and rigidity. Parallel type, screw set

jaws. Arms are 100% adjustable and chrome plated.

G43 Soldering Jig

G43CL Left Angle Clamp Only

G43CR Right Angle Clamp Only

G43CS Straight Clamp Only

F32 SPARK LIGHTER

Handy flint-sparked

lighter. No more

hunting for matches.

F32 Spark Lighter

F32A Extra Flints (Box of 5) for F32

163

SO

LD

ER

ING

Early picture of one of Ferree’s

first locations

We do not have a retail store, HOWEVER,

feel free to stop in for a tour and to pick up

items. Call ahead to schedule a time!!

800-253-2261/269-965-0511

World’s Largest Manufacturer

of Quality Band Instrument

Repair Tools!!

Place an order 24 hours a day

by phone, fax or email.


SOLDER JOINT CLEANING

BRUSHES

This line of wire brushes is used to clean

ferrules and tubing for stronger solder joints.

These brushes quickly clean the corrosion off

pieces to be soldered.

H41 3/8” (9.5mm) Internal ferrule brush



H44 3/4” (19mm) Internal ferrule brush

H45 3/8” (9.5mm) External ferrule brush



H48 3/4” (19mm) External ferrule brush

Internal External

SOLDERING

F31 SILVER SOLDER

This easy flowing silver solder has been used by

manufacturers and repairmen alike for many years.

Melts at 1125° (607°C), flows at 1295°F (701.6°C).

35% silver.

F31A Silver solder, 1/2oz (14.2gm)

F31B Silver solder, 1oz (28.4gm)

F41 SILVER SOLDER FLUX This flux has special components to work well

with copper, nickel, silver and brass. Best suited for

band instrument work. Will not discolor silver.

F41 Flux for Silver Solder 1/2lb. (227g)

164

SO

LD

ER

ING

J60 LOW TEMPERATURE

SILVER SOLDER KIT

The J61 Solder

contains only silver

and tin.

This makes it a

much stronger

solder although it

melts easily. The

unique feature of

Ferree’s J61 Silver

Solder is although it melts at 430°F (221°C), it

doesn’t flow until 535°F (279°C). This gives a plas-

tic range of 105°F (40.6°C) which makes it very

easy to fill a hole. It is unlike other suppliers brands

of solder which melt and flow freely at the same

temperature.

We are making this solder available in a kit, which

includes 8oz (227g) or about 45ft (13.7m) of J61,

1/16” (1.6mm) O.D. and 4 oz (118ml) of the special

J62 flux to use with it.

J60 Low Temperature Solder and Flux Kit

J61 Low Temperature Solder only, 8oz (227g)

J62 Flux for J61, 3.5oz (103.5ml)

Visiting us? Look for the red, white

and blue sculpture out front!!

L2 PROPANE TORCH KIT

This great torch is especially

useful when natural gas is not

available and as a portable

source of heat. Has an all brass

burner tip. Flame similar to the

natural gas F33 and F8. It

“uses” like a real torch. Ideal

for soldering. The kit includes

the burner unit and a fuel

cylinder.

L2 Propane Torch Kit Complete

L2A Replacement

Propane Cylinder

14 oz (400g)

F33 HI HEAT TORCH

General use soldering

torch burns most natural

or artificial gases. Torch

permits use of either

compressed air or ox-

ygen using the op-

tional F33A oxygen tip.

F33 Torch complete with large and small

gas and air tips

F33A Oxygen tip

F33B Replacement Large gas and air tip

F33C Replacement Small gas and air tip

F8 SOLDER TORCH

Our F8 National Torch comes

with two standard tips which

will work efficiently for

compressed air and either nat-

ural or artificial gas.

This torch has a patented

proportional gas mixer.

F8 National Solder Torch

F8A Small gas and air Tip for F8 Torch

F8B Large gas and air Tip for F8 Torch

F8C Oxygen Tip for F8 Torch

SOLDERING

165

SO

LD

ER

ING

An early photo of founder Cliff Ferree

working with an employee

F49 TIX ANTI-FLUX Tix Anti-Flux is used to stop solder from flowing

over silverplate. Heat and flux pieces to be soldered,

then apply anti-flux and reheat before applying

solder.

F49 Tix Anti-Flux

SOLDERING

SOFT

SOLDER

70/30 SOFT

SOLDER

A special alloy 70%

tin, 30% lead,

recommended for band instrument repair work.

Same type originally used by many makers. Makes

a stronger, more enduring bond and therefore

requires slightly more heat. .062” O.D. (1.58mm).

F42 1lb (454g) spool 70/30 soft solder

60/40 SOFT SOLDER Another special alloy. 60% tin, 40% lead.

Requires less heat to use. Buffs off easier than

70/30. .062” O.D. (1.58mm).

F45 1lb (454g) spool 60/40 soft solder

Note: We do not sell 50-50 or 40-60 solder

F46 SOFT SOLDER

FLUX

Special for use with

non-ferrous metals: Copper,

Nickel, Silver and Brass.

Non-evaporating

F46A 3.5oz (103.5ml) bottle

F46B 1qt (.95L) bottle

F95 RIBBON SOLDER

This thin strip of flat solder is useful for many

applications. Excellent for using in tight places, on

silver plated instruments, under sax posts and flute

or sax ribs. Using this special formed solder helps

avoid the over use of solder. Uses less heat; burned

lacquer can be minimized. Made from 60-40 solder.

F95 Ribbon Solder 50ft (15.2mm) Roll

*NEW* F44 94/6

LEAD FREE SOLDER This lead free solder solves your environmental

conerns. It is alloyed from 94% tin and 6% silver,

NO LEAD. Stronger than 70/30, “works” like

70/30. Superior to 96/4, because the 94/6 is more

“workable”. .062” (1.58mm) O.D.

F44 1 lb (454g) of lead free solder

166

SO

LD

ER

ING


D42 REVERSIBLE SCRAPER

Plated 4-1/2” (114mm) adjustable handle has

knurled adjustment nut and collet type chuck for

blade adjustment. The 3/16” (4.8mm) blade is

thinner than most scrapers.

D42 Scraper

D42A Replaceable blades

SOLDERING

N13 CORNET/TRUMPET BELL

MOUNTING JIG This jig will hold a mouthpiece or a bell on a

cornet or trumpet in place while it is being soldered.

Will also hold all braces securely in place.

N13 Bell Mounting Jig for Cornet and

Trumpet

SOLDERING CLAMPS

This clamp is designed to be used with the

largest tubas as well as small instruments. Its

distinguishing features include a threaded shaft that

is long enough to eliminate the need to disassemble

the clamp and reverse the slide, one bearing pad

that rotates to give a solid bearing surface when

soldering nonparallel tubes or tapered bells and

tubing, and a bearing pad that can be adjusted up or

down to compensate for different tubing diameters

or placements that are being clamped.

Although this clamp is designed to be used with

larger brass instruments it will provide excellent

solder clamping for smaller instruments. Note that

the bottom of the heavy-duty slide fitting has been

tapered to allow fitting between slide tubes when

necessary.

N19 Soldering Clamp

SOLDERING CLIPS

These stainless steel solder clips will not rust and

do not corrode as easily from the heat and flux.

Hold braces and flanges while silver soldering.

Hold nibs when soldering on crooks, finger rings,

etc.. Save time by eliminating wiring. Makes a

neater solder job.

E45A Small Solder Clip

E45B Large Solder Clip

L10 BINDING WIRE

1/4 lb. (113g) specially annealed iron wire for

binding parts to horns for soldering. 19 gauge. 50

feet.

L10 Binding Wire

NON-ASBESTOS MILLBOARD

Protect your bench from open flame when silver

soldering keys or braces with this high strength, sol-

id, longer life material, which will not crumble.

J45 12” X 12” X 1/2” (305 X 305 X 12.7mm)

J48 6” X 12” 1/2” (152mm X 305 X 12.7mm)

N19

N13

167

SO

LD

ER

ING

Email orders to us at:

[email protected]

World’s Largest Manufacturer

of Quality Band Instrument

Repair Tools.

Documents

Page 113 Thru 167