Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Congratulations on your purchase of a Tusk Product. Please take note of the information and instruc-
tions below to get the most out of your Tusk Product.
Package Contents:
1-Full Glass Windshield
1-Upper filler black powder coat
4– Billet 1.75” roll cage clamps
4– Roll cage clamp gaskets
4–Button Head (Allen) bolts M8 x 1.25 x 16mm black
4-M8 Washers black
6-Button Head M6 x 1.0 x 25mm
6-M6 x 1.0 nyloc
8–Allen Head Cap Screws M6 x 1.0 x 20mm
1- 39” Flap Seal
2– 1 3/4” Vinyl Dipped P-Clamp
5-Rubber bumps stops
1-1/4” x 1/2” Foam tape 3ft long
INSTALLATIO
N I
NSTRU
CTIO
NS A
ND
IN
FO
RM
ATIO
N
Part # 1824330001 Full Glass Windshield Polaris RZR 1000/900
Vehicle Fitment
POLARIS RZR Trail 900 2015-2017
POLARIS RZR 1000 XP 2014-2017
POLARIS RZR 1000 XP-4 2014-2017
POLARIS RZR 1000 XP Turbo 2016-2017
POLARIS RZR 1000 XP-4 Turbo 2016-2017
POLARIS RZR 1000 S 2016-2017
POLARIS RZR 900 S 2016-2017
Roll cage clamp gaskets (4)
Billet 1.75” Roll Cage Clamp (4)
Tusk Full Glass Windshield
Button head M8 x 1.25 x 16mm (4)
M8 Washer Black (4)
Allen Cap Screw M6 x 1.0 x 20mm (8)
Flap Seal 39” (1)
INSTALLATIO
N I
NSTRU
CTIO
NS A
ND
IN
FO
RM
ATIO
N
Part # 1824330001 Full Glass Windshield Polaris RZR 1000/900
Button Head M6 x 1.0 x 25 mm bolt (6) M6 x 1.0 Nycloc (6)
Upper Filler (1)
1 3/4” Vinyl dipped p-clamp (2)
1/4” x 1/2” Foam Tape 3FT Rubber Bump Stops (5)
1. Locate the four supplied roll cage clamps, four rubber gaskets and eight allen cap screws and
loosely install them on the front window posts approximately 4” up from the joint in the cage
and 17” up as shown in image #1. Two clamps will be installed on each side. Leave them
loose enough that you can slide them up and down.
INSTALLATIO
N I
NSTRU
CTIO
NS A
ND
IN
FO
RM
ATIO
N
Part # 1824330001 Full Glass Windshield Polaris RZR 1000/900
2. Lay the window down on a flat clean surface and install the supplied rubber flap seal along the
bottom edge. Prior to installing, pinching the trim together may be required in order to achieve a
tight fit on the metal window frame. See images 2 & 3.
Approx 17”
Image 1
Approx 4”
Rubber Flap Seal
Image 2 Image 3
INSTALLATIO
N I
NSTRU
CTIO
NS A
ND
IN
FO
RM
ATIO
N
Part # 1824330001 Full Glass Windshield Polaris RZR 1000/900
OEM Visor Image #4
3. The Tusk full glass windshield may be installed with or without the Polaris OEM front visor. See
Image #4. At this time you will need to decide if you want to use it or not.
4. If you have chosen to use the OEM visor you will need to install the 1/4” x 1/2” Foam tape on the
upper edge of the window as shown in the image below. Skip this step if you chose not to use the
OEM visor.
Install foam tape here
Remove plastic plugs
INSTALLATIO
N I
NSTRU
CTIO
NS A
ND
IN
FO
RM
ATIO
N
Part # 1824330001 Full Glass Windshield Polaris RZR 1000/900
4. Installing without OEM front visor: Locate the (4) M8 x 1.25 x 16mm button head bolts and with
a helper install the Tusk full glass windshield on the machine. Tighten only finger tight at this
time. Adjust window up, down left and right to achieve optimal desired fit. This will require that
you adjust the clamps up or down on the roll cage. It is best that the window does not have a
substantially amount of weight bearing on the hood, allow the roll cage clamps to bear the
weight. Tighten all bolts when the desired fit is achieved.
5. Next remove the (4) plastic plugs from the top edge of the window and set aside, these will not
be used when installing without the OEM visor.
Install (4) M8 button headbolts & flat washers
INSTALLATIO
N I
NSTRU
CTIO
NS A
ND
IN
FO
RM
ATIO
N
Part # 1824330001 Full Glass Windshield Polaris RZR 1000/900
6. Locate the supplied upper filler panel, M6 x 1.0 x 20mm bolts, M6 nylocs and vinyl dipped p-
clamps.
7. Install the filler panel behind the front windshield as shown in the images below. Tighten all
hardware finger tight. Make final adjustments to window and filler panel and tighten all hard-
ware.
M6 bolt and nyloc
Filler Panel
M6 bolt, nyloc &vinyl dipped p clamp
INSTALLATIO
N I
NSTRU
CTIO
NS A
ND
IN
FO
RM
ATIO
N
Part # 1824330001 Full Glass Windshield Polaris RZR 1000/900
8. Installing with OEM front visor: Install the OEM visor on your machine.
9. Locate the (4) M8 x 1.25 x 16mm button head bolts and with a helper install the Tusk full glass
windshield on the machine. Tighten only finger tight at this time. Adjust window up, down left
and right to achieve optimal desired fit. This will require that you adjust the clamps up or down
on the roll cage. It is best that the window does not have a substantially amount of weight bear-
ing on the hood, allow the roll cage clamps to bear the weight. Tighten all bolts when the de-
sired fit is achieved.
Install (4) M8 button head bolts & flat washers
10. Locate the (5) supplied bumps stops. When your vent door is in the open position it will rest on
the dash. Identify the locations on the vent door that will come in contact with the dash and in-
stall two of the bumps stops in that location. You are supplied with (3) extras.
11. Enjoy the comfort of your new Tusk windshield!