PC Wiring System Series PCW - SMC ETechcontent2.smcetech.com/pdf/PCW.pdf · PC Wiring System Series Connection cable with connector P. 12 ... PC Wiring System Series PCW 1. ... Connected

CAT.ES02-20 A

PC Wiring System

Series PCW

The PC wiring system is a revolutionary new system that simplifieswiring between a PLC and all types of connected equipment.

Features 1

Input32

points

Output64 points

CompatiblePLC Manufacturers

24VDCPowersupply

OMRON CorporationMitsubishi Electric CorporationFuji Electric Co., Ltd.Hitachi Ltd.Toshiba CorporationYasukawa Electric CorporationSHARP CorporationYokogawa Electric Corporation Matsushita Electric WorksKeyence CorporationKoyo Electronics Industries Co., Ltd. Branch unit

PLC directconnected type

16 point input unitBox mount type

16 point input unitDIN rail mount type

16 point output unitDIN rail mount type

8 point output unit (terminalblock type) DIN rail mount type

HI

16points

32points

32points

16 points

16 points

16points

Branch unitDIN rail

mount type

With 16 points separated

With 16 points unseparated

16 points

16 points

Input Output

P. 2

P. 3

P. 6

P. 6

P. 6

With 32 points separatedWith 32 points unseparated

Connectioncablewith connector

P. 12

Connectioncable with connector

P. 13

32 pointreduced

common typealso available.

P. 5

32 point output unitDIN rail mount type

32 points

Output32

points

Output32

points

A revolutionary new wiring system...

Series PCW

Features 2

LO

16points

16points

32points

16 points

8 points

P. 4

P. 8

P. 14

PC Wiring System

Series PCW

Connectioncable withconnector

P. 12

Connectioncable withconnector

P. 11

Connection cablewith connector

P. 13

Check unit

The PC wiring system simplifies wiring between a PL

Features 3

PC wiring system terminal block unit (40P connector + 64 pin terminal block + Added value)

General purpose terminal block unit (40P connector + 40 pin terminal block)

Standard specifications Fujitsu Ltd. FCN connector specifications

In the case of a general purpose terminal block, common and power supply terminal blocks are not supplied as shown below, making it necessary to purchase them separately. Labor is also required for assembly.

In the case of the PC wiring system terminal block unit, it is only necessary to purchase one piece and nothing else is required. (It is also compact, and the PLC manufacturer's address is stated directly on the label.)

P. 11, 12, 13

Commonality achieved with branch unit

Simple parallel type

Improved wiring efficiency and ease of handling

Fujitsu Ltd. FCN connector specifications also available.

Connection cable

Space saving

Commonality achieved with branch unit The branch unit separates each PLC manufacturer's 32 point I/O into a 16 point common pin layout.

Conversion to a common pin layout makes it possible to connect the pin layout to SMC manifold solenoid valves and other manufacturers' relay equipment without even thinking about it.

Power can be supplied to the PLC's I/O unit.

Compatible branch units are available for each PLC manufacturer's I/O.

Simple parallel type Unlike serial transmission, there is no need to worry about transmission delay time.

Visually and sensually easy to understand, maintenance is easy for start-up, debugging and trouble shooting.

Improved wiring efficiency and ease of handling Reduced wiring equivalent to a serial transmission system can be attained with a special cable.

The single block pressure connection system using a connector allows standardization of wiring work, prevents miswiring and greatly improves work efficiency.

Fujitsu Ltd. FCN connector specifications also available.

∗ Consult SMC regarding compatibility.

Connection cable The special cable with power supply line consists of a flat cable and power supply lines enclosed in a

single sheath, making the conventional separate wiring of the power supply line unnecessary.

Maximum wiring length 49m

Also available without the power supply lines specification.

Space saving

LC and all types of connected equipment.

Features 4

Connected to manifold solenoid valves

With input from a sensor switch, etc. Reduces wiring labor Prevents miswiring Requires fewer I/O points

PC Wiring System Application Examples

Example

1

Example

2

Manifold solenoid valves(16 point output)

Branch unit(32 point output→16 point output x 2)

PLC (32 point output)

Manifold solenoid valves(16 point output)

Input unit(16 point input)

Input unit(8 point input)

Cascade connectionInput unit (8 point input)

Branch unit(32 point input→16 point input x 2)

PLC(32 point input)

Reduces wiring labor Prevents miswiring ∗ Commercially available relay terminals,

etc., can also be connected

24VDC

2A

0.3A

5MΩ or more at 100VDC

0.5kV

500m/s²

0.4 to 0.6Nm/0.4 to 0.7Nm

0.5 to 0.6Nm/0.5 to 0.7Nm

7mm

AWG26 to 14 (0.13 to 2.5mm²)

AWG26 to 12 (0.13 to 4mm²)

Common Specifications

Cable Specifications

Rated voltage

Rated current

Insulation resistance

Withstand voltage

Impact resistance

Flat cable

Power lines

Sheath O.D.

Power supply line

Communication line

Power terminal (Phillips screwdriver/Flat head screw driver)I/O terminal (Phillips screw driverFlat head screw driver)

Power terminal

I/O terminal

Power terminal

I/O terminal

Brown

Blue

PVC sheath

Flat cableAWG28

Power linesAWG20 (20, 40 cores)

With power lines

AWG28 (7 wires/0.127mm)

AWG20 (21 wires/0.18mm) ——

20 cores

10.3mm

40 cores

12.0mm

20 cores

8.7mm

34 cores

11.8mm

40 cores

13.0mm

Without power lines

Screwtighteningtorque

Wire strippinglength(recommended)

Connecting wire size

Term

inal

blo

cksp

ecifi

catio

ns

PC Wiring System

Series PCW

1

18.2

(5.2)16.5

CN1CN2

1NDN–1D/1

–+

70.1

23.127.4

+ –

Dimensions

Specifications

Weight

Ambient temperature

25g

–25 to 55°C

Compatible PLC's and Models

PLCmanufacturer

OMRONCorporation

Mitsubishi Electric

Corporation

YokogawaElectric Corp.

I/Opoints

32

32

32

64

64

64

Input

Compatible model Model Model

Output

PCW-993155

PCW-993106

PCW-993104

C200H-ID216C200H-ID218

A1SX41

F3XD32-3N

F3XD64-3N

AX42A1SX42

C500-ID219C200H-ID217C200H-ID219

Note 1)

Note 3) PCW-993156

PCW-993107

PCW-993105

C200H-OD218

C500-OD213C200H-OD219

A1SY41

F3YD32-1A

F3YD64-1A

AY42A1SY42 Note 2)

Note 4)

CautionWhen removing a cable with connector, a PCW-04T puller is required.

Two pieces are required for 64 points of input/output.Note 1) Combine one piece each of PCW-993106 and PCW-993108 (the PLC connection side connectors are

reversed).Note 2) Combine one piece each of PCW-993107 and PCW-993109 (the PLC connection side connectors are



reversed).

PLC connection

Can be directly mounted on PLC.

PLC

Compatible model

Note) Since some series PCW specifications are included in the common specifications, also refer to the common specifications on page 1.

Series PCWBranch Unit: PLC Direct Connected Type

2

Dimensions

Specifications

Weight

Ambient temperature

80g

–25 to 80°C


PLCmanufacturer

OMRONCorporation

MitsubishiElectric

Corporation

Fuji ElectricCo., Ltd.

Hitachi, Ltd.

Toshiba Corp.

Yasukawa Electric

SHARPCorporation

MatsushitaElectric Works

Koyo ElectronicsIndustries Co., Ltd.

Keyence Corp.


I/Opoints

32

32

32

32

32

64

64

64

64

64

64

64

64

64

64

Input Output

PCW-993023A

C200H-ID216C200H-ID218CQM1-ID213

KZ-C32X Note 1)

PCW-993033A

PCW-993015A PCW-993017A

PCW-993019A PCW-993021A

PCW-993029A PCW-993039A

C200H-OD218CQM1-OD213

C500-ID219C200H-ID217C200H-ID219

A1SX41AJ35TC1-32D

AX42A1SX42

AY42A1SY42

A1SY41AJ35TC1-32T

FTU125ANS-X64-I

FTU222ANS-Y64-TI

PCW-993025A PCW-993035ADI335DI-6241

DO335DO-6242

JW-34NCJW-234N

JW-32SCJW-232S

AFP33027AFP33028AFP33068

AFP33487

XDC24D2H YTR24DH

PCW-993049A PCW-993043A

PCW-993045A PCW-993047A

PCW-993027A PCW-993037A

PCW-993168A PCW-993169A

U-19TPCW-993200A PCW-993201A

PCW-993139A PCW-993140A

JAMSC-B2605 JAMSC-B2604

JW-64NC JW-62SC

F3XD32-3N F3YD32-1A

F3XD64-3N

U-09N

F3YD64-1A

C500-OD213C200H-OD219

KZ-C32T Note 1)

28.3

45

103

16.7

(3.6)

4.1

5.1

10.5 10.5

OUTIN

ID!/4-A

CNO

CN2CN1

C1 C2 8 7 6 5 4 3 2 1

RS–

4950.5

4.5

55

Two pieces are required for 64 points of input/output.Note 1) The mounted connector has 34 pins.

PLC connection

Connected to PLC via connection cable.

PLC

Compatible model Model Compatible model Model


∗ Refer to pages 11 and 13 for the junction cable part number.

Series PCWBranch Unit: DIN Rail Mount Type

3

Keyence Corp.


Two pieces are required for 64 points of input/output.Note 1) The mounted connector has 34 pins.

OMRONCorporation

MitsubishiElectric

Corporation


Hitachi, Ltd.

Toshiba Corp.

Yasukawa Electric

SHARPCorporation

MatsushitaElectric Works

32

32

32

32

32

64

64

64

64

64

64

64

64

64

64

PCW-990344A

C200H-ID216C200H-ID218CQM1-ID213

KZ-C32XNote 1)

PCW-990345A

PCW-993157A PCW-993158A

PCW-993159A PCW-993160A

PCW-990355A PCW-990356A


C500-ID219C200H-ID217C200H-ID219

A1SX41AJ35TC1-32D

AX42A1SX42

AY42A1SY42

A1SY41AJ35TC1-32T

FTU125ANS-X64-I

FTU222ANS-Y64-TI

PCW-990386A PCW-990387ADI335DI-6241

DO335DO-6242

JW-34NCJW-234N

JW-32SCJW-232S

AFP33027AFP33028AFP33068

AFP33487

XDC24D2H YTR24DH

PCW-993011A PCW-993012A

PCW-993163A PCW-993164A

PCW-993013A PCW-993014A

PCW-993166A PCW-993167A

U-19TPCW-993202A PCW-993203A

PCW-993161A PCW-993162A

JAMSC-B2605 JAMSC-B2604

JW-64NC JW-62SC

F3XD32-3N F3YD32-1A

F3XD64-3N

U-09N

F3YD64-1A

C500-OD213C200H-OD219

KZ-C32T Note 1)

Dimensions

Specifications

Weight

Ambient temperature

210g

–25 to 55°C

53.555

4.5

55

1 1F16D40

+

E F 10 11 12 13 14 15 17 18 19 1A 1B 1C 1D 1E1E

-+-+-+-+-+-+-+-+-+-

C

+

B

-

A

+

9

-

8

+

7

-

6

+

5

-+

3

-

2

+-

16.7

45 28.3

178

4.1

10.510.5

5.1

OUTINAX/140-A

01 CHCH

RS–

(3.6)

(3.7)

PLC connection


PLC

PLCmanufacturer

I/Opoints

Input Output

Compatible model Compatible model ModelModel


∗ Refer to page 11 for the junction cable part number.

Koyo ElectronicsIndustries Co., Ltd.


Series PCW32 Point Input/Output Unit

4

OMRONCorporation

Mitsubishi Electric

Corporation

ToshibaCorporation



Keyence Corp.

Output points

32

32

32

32

64

64

64

64

64

Compatible model Model

PCW-993224

PCW-993222

PCW-993223

PCW-993225

PCW-993194

PCW-993193


AY42A1SY42

A1SY41AJ35TC-32T

DO335DO-6242

F3YD32-1A

F3YD64-1A

KZ-C32T

FTU222ANS-Y64-T1

C500-OD213C200H-OD219

Note 1)


Two pieces are required for 64 points of output.Note 1) The mounted connector has 34 pins.

Dimensions

Specifications

Weight

Ambient temperature

130g

–25 to 55°C

4.5

113

131211

112111110

1098

109108107

765

106105

4

104103

32

102

15

115

14

114

1

101100

0+

-

53.555

OD/040LPOUT

CH1

–

+

CH

RS–

113

28.3

45

16.7

103

5.1

4.1

10.5 10.5(3.6)

(3.7)

PLC connection


PLC

PLC manufacturer


∗ Refer to page 11 for the junction cable part number.

Series PCW32 Point Output Reduced Common Unit

5

Dimensions

Models

Input

OutputPCW-993051APCW-993052A

Specifications

Weight

Ambient temperature

125g

–25 to 80°C

Terminal Block: DIN Rail Mount Type

5553.5

–

F

+

E

–

D

+

C

–

B

+

A

–

9

+

8

–

7

+

6

–

5

+

4

–

3

+

2

–

10

+–

+

4.5

55

28.3

45103

16.7IN

OUT

CN1

RS-

CHF16/1D-A

10.5 10.5

(3.7) 5.1

4.1

PCW-993055APCW-993056A

480g

–25 to 80°C

Terminal Block: Box Mount Type

33.5139

59

–– + –+ – v– + –– ++ –– + – +

+FEDCBA9875 642 31+ 0

INOUT

1 2 C1

0/118-A

C2

–

+

CN

1

CN

2

CH

(3.7

)

(3)158

55

8

6

67.4

10

40

1614 16 1614 1614

41.2(2)

65

1.2

4-M3 x 0.5 2-ø5 machined for bar ringMounting hole5

101055 55

2525

55 55

6-ø4

2-ø8

Dimensions

Models Specifications

Input

Output

Weight

Ambient temperature




6

PCW-993132APCW-993133A

70g

–25 to 80°C

Connector: DIN Rail Mount Type

Output PCW-993195 80g

–25 to 80°C

Terminal Block: DIN Rail Mount V Type16 Point Output Reduced Common Unit

4.5

16.7

4.1

5.1113

28.3

4510.510.5 103

4950.5

F16/1DTB–A

–S+

321

21

IN

CH

CN–PS

CN–FCN–ECN–D

CN–5

CN–C

CN–4

CN–8

CN–3

CN–A

CN–2

CN–9

CN–1CN–PC

CN–6CN–7

RS–CN–0

CN–8

–+

(3.6)

53.55579

28.3

45

16.7

69

4.5

5.1

4.1

10.5 10.5

F16/0DLPOUT

4

CB

32

A

765

F]ED

1

98

0+

–

–

+

L

HCH

RS–

(3.6)

(3.7)

CautionConnectors are manufactured by Molex Japan Co., Ltd., and are not handled by SMC.Please order them separately.Housing: 51103-0300Crimp pin: 50351-8100

Input

Output

Weight

Ambient temperature

Dimensions

Model Specifications

Weight

Ambient temperature

Dimensions

Model Specifications




7

Dimensions

PCW-993053APCW-993054A

105g

–25 to 80°C


Dimensions

PCW-993057APCW-993058A

365g

–25 to 80°C


5553.5

28.3

45

103

4.5

16.7

CH

––– –– –– –––

+764 5320+

F8/1D-A

CN2CN1

HL

76543210

+

–

1 2 3 4 C

1

RS–

55

10.5 10.5

4.1

5.1(3.7)

59

33.599118

55

8

1.2

4-M3 x 0.52-ø5 machined for bar ringMounting hole

51010

667

.4

10

2525

40

701614 16 1614

41.2(2)

65

70

2-ø8

4-ø4

–+ ––++– –– +

+75 6431 20+

OUTIN

1 2 C1

D/18-A

L

H

0 1 2 3 4 5 6 7

–

+

C2

CN

2

CN

1

CH

(3.7

)

(3)

7

6

1

0L H

……

7

6

1

0

HL

……

Models

Input

Output

Specifications

Weight

Ambient temperature

Models

Input

Output

Specifications

Weight

Ambient temperature



HI/LO setting(8 point input/output unit) Since most PLC manufacturers use 16 points of input/output in units of one channel, 8 point input/output units can be connected in a series of two units. In this case, either the “Lo” 0 to 7 or “Hi” 8 to F address can be selected by means of these jumpers (short-circuit sockets). To select the “Lo” side address the “Lo” side is shorted. It is set to the “Lo” side when shipped from the factory.

Note) When two 8 point input/output units are used in a cascade connection, set the jumpers (short-circuit sockets) so that the jumpers (short-circuit sockets) of both units are not set to the same address (i.e., not “Lo” and “Lo” or Hi” and “Hi”).(Trouble will occur during input due to the activation of OR circuits for two sensors.)Use caution, because incorrect connection of input and output for 8 point or 16 point input/output units following the branch unit, will cause short-circuiting of the power supply.

“Hi”“Lo”

Series PCW8 Point Input/Output Unit: HI/LO Setting Type

8

Dimensions

HI

LO

HI

LO

PCW-993210PCW-993211PCW-993212PCW-993213

105g

–25 to 80°C


Dimensions

365g

–25 to 80°C


Models

HI

LO

HI

LO

Input

Output

PCW-993214PCW-993215PCW-993216PCW-993217

F8/ID-A

113 5553.5

28.3

45103

4.5

16.7

OUTIN

1 2

C1

C2

––– –– –– –––

–FEC DBA8–

CN2CN1

+

–

9

HICH

RS–

10.5 10.5

4.1

5.1(3.7)

67.4

(2)(2) 41.2118

702-ø5

HI OUTIN

1 2 C1

MDP/18H

–

+

C2

CN

2

CN

1

CH

HI/LO limit typeFor this type, the upper or lower position is fixed, and it is not necessary to set jumpers (short-circuit sockets).Lo type: The address assignment is fixed at “Lo” 0 to 7.Hi type: The address assignment is fixed at “Hi” 8 to F.

Specifications

Weight

Ambient temperature

Specifications

Weight

Ambient temperature

Models

Input

OutputNote) Since some series PCW specifications are

included in the common specifications, also refer to the common specifications on page 1.


Series PCW8 Point Input/Output Unit: HI/LO Limit Type

9

Dimensions

Models

HI (master) Input

Output

PCW-993135APCW-993136A

Specifications

Weight

Ambient temperature

75g

–25 to 80°C

Connector: DIN Rail Mount Type

Master

Dimensions

Models

LO (slave) Input

Output

PCW-993137APCW-993138A

Specifications

Weight

Ambient temperature

55g

–25 to 80°C

SlaveCN1PS

Address

4.5

5.179

4.1

16.7

10.510.5 69

28.3

45

4950.5

F8/1D2TB-A +–0

000

LH

CHCN-3 (B) CN-2 (A) CN-1 (9) CN-0 (8)

CN-7 (F) CN-6 (E) CN-5 (D)

IN

CN-4(C) –S+

321

1

2

RS-

CN-PC1

+

(3.6)

4.5

4.1

16.7

5.1113

45 28.3

10.510.5 103

4950.5

F8/1D1TB-A

+–

CN-PS2CN-PS1RS-

21001

CH CN-PC2CN-PC1

1 2 3

+ S –

CN-7CN-6CN-5CN-4CN-3CN-2CN-1CN-0

IN

–

+–+

(3.6)

Manifold solenoid valves

CN-PC1 CN-PC2

Address 8 to FAddress 0 to 7

Connector type8 point output unit(master)

8 point relay terminalMatsushita Electric WorksRT1S-OD08-V-SRT1S-ID08-V-S

CN-PC1


Connector type8 point I/O unit(slave)

Connector type8 point I/O unit(master)

Connector type8 point I/O unit(slave)

CN-PC1 CN-PC1CN-PC2


1. 2. 3.

Cascade connection examples (Consult with SMC in case of a cascade connection.)

CautionConnectors are manufactured by Molex Japan Co., Ltd., and are not handled by SMC. Please order them separately.Housing: 51103-0300, Crimp pin: 50351-8100



Cascade connectionA connector type 8 point input/output unit can be used with a cascade connection of a master unit and slave unit, or a cascade connection of a master unit with another device.Note) Connector type input/output units are not available with HI/LO settings.

1st unit: Connector type 8 point input/output unit(master unit)

2nd unit: Connector type 8 point input/output unit(slave unit)

1st unit: Connector type 8 point output unit(master unit)

2nd unit: Manifold

1st unit: Relay terminal2nd unit: Connector type 8 point input/output unit

(slave unit)

Series PCW8 Point Input/Output Unit: HI/LO Limit Type

10

For Connection of PLC Input/Output Card to PCW Unit

PCW 02

Power supply lineYesNo

SymbolNilN

Lead wire length0.5m1m1.5m2m3m5m

Symbol005010015020030050

Power supply line

SpecificationsStandard specificationsFor connection of PCW unit for Keyence Corp. PLC I/O card (KZ-C32X, KZ-C32T)For connection of PCW unit for Hitachi, Ltd. PLC I/O card (XDC24D2H, YTR24DH)

Symbol020506

Specifications

005Lead wire length

• PLC input/output card to PCW branch unit• PLC input/output card to PCW 32 point unit

DimensionsSeries PCW-02

With power linesPLC connection side

PCW unit connection side

Fujitsu FCN40 pin connector

MIL-C-8350340 pin connector

Without power linesPLC connection side


Fujitsu FCN40 pin connector


Series PCW-05 With power linesPLC connection side PCW unit connection side



Without power linesPLC connection side PCW unit connection side



Series PCW-06 With power linesPLC connection side PCW unit connection side



Without power linesPLC connection side PCW unit connection side



Contact your SMC sales representative regarding connector cables with lead wire lengths other than those in the table above.

Note) When using a PCW unit equipped with Fujitsu FCN connector, contact your SMC sales representative as the connector cable is different.

Series PCWPC Wiring SystemConnector Cable

11

Dimensions

With power lines

Branch unit: PLC direct connecting typeconnection side



IDEC Izumi JM1S20 pin connector


Without power lines




Branch Unit:Connection of PLC Direct Connecting Type

to PCW Unit

PCW 04

Power supply linesYesNo

SymbolNilN


Symbol005010015020030050

Power supply lines

005Lead wire length

Branch Unit:Connection of PLC Direct Connecting Type

to Manifold Solenoid Valves

PCW 04

Powersupply lines

YesNo

Applicable manifoldsolenoid valve kit

G kitJ kit

Symbol

VN


Symbol005010015020030050

Power supply lines

005Lead wire length

Refer to the section starting on page 16 for details regarding applicable manifold solenoid valves.

With power lines



Manifold solenoid valve connection side

(G kit)

Manifold solenoid valveconnection side

(J kit)



Without power lines



Dimensions

V

• Branch unit: Connection of PLC direct connecting type to PCW 16 point unit

• Branch unit: Connection of PLC direct connecting type to PCW 8 point unit


• Branch unit: Connection of PLC direct connecting type to manifold solenoid valves



12

Dimensions

With power lines




Without power lines








Connection ofPCW Unit to PCW Unit

PCW 01

Power supply linesYesNo

SymbolNilN

Lead wire length

0.5m1m1.5m2m3m5m

Symbol005010015020030050

Power supply lines

005Lead wire length

Connection of PCW Unit to Manifold Solenoid Valves

PCW 01

Lead wire length

0.5m1m1.5m2m3m5m

Symbol005010015020030050

005Lead wire length

With power linesManifold solenoid valve connection side

(G kit)

Manifold solenoid valve connection side (J kit)



Without power lines



Dimensions

V

Power supply lines

YesNo

Applicable manifoldsolenoid valve kit

G kitJ kit

Symbol

VN

Power supply lines

Refer to the section starting on page 16 for details regarding applicable manifold solenoid valves.

• Connection of PCW branch unit to PCW 16 point unit

• Connection of PCW branch unit to PCW 8 point unit

• Connection of PCW 8 point unit to PCW 8 point unit

• Connection of PCW branch unit to manifold solenoid valves

• Connection of PCW 8 point unit to manifold solenoid valves



13


24VDC

0.3A

0.5kV

0.4 to 0.6Nm/0.4 to 0.7Nm

7mm

AWG26 to 14 (0.13 to 2.5mm²)

–25 to 80°C

Specifications

Dimensions

How to Order

Internal Circuit Diagram

Rated voltage

Rated current

Withstand voltage

Thread tightening torque(Phillips screw driver/Flat head screw driver)

Wire stripping length

Connecting wire size

Ambient temperature

• Effective for software/hardware debugging and maintenance of PC wiring systems and other compatible systems.

• Signal monitoring possible with LED.

• Switches allow forced release and forced ON operation of connections between connectors in one bit increments.

• Allows voltage measurement and wave form observation of signals between the check terminal and common terminal.

PCW 993065

Check unit

Term

inal

blo

ck

116 22.5

(41)

130 (149

)

Series PCWCheck Unit

14

15

Manifold ValvesP. 18

P. 34

P. 54

5 Port Solenoid Valve

Series SQ1000/2000 • Low profile compact manifold• Stacking manifold type makes it easy to increase or decrease

the number of stations• Maintenance of valves is simplified by the one-screw mounting• A variety of options

Back pressure check valve, Built-in silencer, Name plate, etc.• Seal type allows selection of metal seals or rubber seals

Rubber Seal5 Port Solenoid Valve

Series SZ3000 • Size and weight reductions have been realized by eliminating the manifold base• The plug-in cassette system makes valve replacement easy• A plug-in manifold has been achieved with a height of 43.5mm (including DIN rail)• Valves with switches are available to allow each valve to be turned off individually• 4 position dual 3 port valve provided by combining two 3 port valves in one valve

body• Valve with back-pressure check function available• Low power consumption: 0.65W (with light)

(Current value: 27mA, 24VDC)


Series SX3000/5000 • Low power consumption: 0.65W

(with light)(Current value: 27mA, 24VDC)

• Compact with high flow rateCv factor 1.7 to 3 times greater with same body width as previous series

• High reliabilityLong life exceeding 50 million cycles

• Main valve and pilot valve common exhaust construction eliminates pilot valve exhaust mist and noise


Series SY3000/5000 • Low power consumption: 0.55W (with light)

(Current value: 23mA, 24VDC) • Compact with high flow rate

Cv factor 1.7 to 3 times greater with same body width as previous series



5 Port Solenoid ValveBody Ported Type/Flip Plug-in Unit

Series VQ1000 • Compact manifold for efficient use of space• Valves can be replaced without disassembling the entire manifold• Seal type allows selection of metal seals or rubber seals

5 Port Solenoid ValveBase Mounted Type/Plug-in Unit

Series VQ1000/2000 • Space saving design locates all pilot valves on one side• One-clamp construction with no screws for easy valve replacement• A variety of options

Back pressure check valve, Built-in silencer, Name plate, etc.

• Seal type allows selection of metal seals or rubber seals

P. 44

P. 28

16

Manifold Electrical Wiring

Common Shared Wiring Connectors

• With power supply terminals (G kit) • Without power supply terminals (J kit)

SOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.B

201816141210861917151311975

3.4

1.2

–+

Terminal no.

Electrical circuit diagram (The wiring below indicates all double solenoid connections)

1 station

24VDC

2 stations 3 stations 4 stations 5 stations 6 stations 7 stations 8 stations

SOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.BSOL.ASOL.B

20181614121086

1917151311975

3.4 24VDC (–)

1.2 24VDC (+)

Terminal no.

Electrical circuit diagram (The wiring below indicates all double solenoid connections)

1 station 2 stations 3 stations 4 stations 5 stations 6 stations 7 stations 8 stations

Common shared wiring connector assemblies are also available for series SX/SZ. Refer to the catalog for each series for details.

Applicable seriesSeries SZ3000Series SX3000/5000Series SY3000/5000Series VQ1000/2000 (base mounted type)

Applicable seriesSeries SQ1000/2000Series VQ1000 (body ported) Series VQ1000/2000 (base mounted type)

For standard electrical wiring specifications, the internal wiring for up to eight stations is double wiring (connected to SOL.A and SOL.B) for each station regardless of the valve or option type. Connect to SOL.A in case of single solenoids. Furthermore, when mixed single and double wiring is required, indicate this on a manifold specification sheet. (except Series SY)

For standard electrical wiring specifications, the internal wiring for up to eight stations is double wiring (connected to SOL.A and SOL.B) for each station regardless of the valve or option type. Connect to SOL.A in case of single solenoids. Furthermore, when mixed single and double wiring is required, indicate this on a manifold specification sheet.

Manifold Valve Common Specifications

17

Series

Type of actuation A, B port size

2 position 3 position 4 position One-touch fitting

Effective areamm²

(Cv factor) Single/Double

3.2 (0.18)

4.5 (0.25)

11.7 (0.65)

14.8 (0.82)

—

—

—

—

—

—

Sin

gle

Dou

ble

(Lat

chin

g/D

oubl

e so

leno

id)

Clo

sed

cent

er

Exh

aust

cen

ter

Pre

ssur

e ce

nter

Dua

l3

port

val

ve C3

(ø3.2)

C4

(ø4)

C8

(ø8)

C6

(ø6)

SQ130Metal sealSQ131Rubber sealSQ230Metal sealSQ231Rubber seal

• Low profile compact manifold• Stacking manifold type makes it easy to increase or decrease

the number of stations• Maintenance of valves is simplified by the one-screw mounting• A variety of options

⋅ Back pressure check valve, Built-in silencer, Name plate, etc.• Seal type allows selection of metal seals or rubber seals

18

5 Port Solenoid Valve

Series SQ1000/2000

How to Order Manifolds

01

Metal sealRubber seal

Seal type

Series

Symbol Stations1 station

16 stations

01

16

Valve stations

SS5Q 3 (-00T)JD0

Symbol02 to 24

BK

N

RS

Option specificationsSpecifies DIN rail length Back pressure check valve on all stationsSpecial wiring specification (except double wiring)

With name plate(valve with side port specification only)

External pilot specification

Built-in silencer

SymbolNilD

K Note 1)

Y Note 1)

R Note 2)

SpecificationsStandard type (1W)

2 position double (double solenoid specification)High pressure type (1MPa 1W)

Available only for SQ1000 with metal sealLow power consumption type (0.5W)


Function

Note 1) Except double (latching) typeNote 2) Except dual 3 port valveNote 3) When specifying two or more options, enter

symbols in alphabetical order.

12 Note 1)

345

A Note 2)

B Note 2)

C Note 2)

2 position single2 position double (latching/double solenoid)3 position closed center3 position exhaust center3 position pressure centerDual 3 port valve N.C. + N.C.Dual 3 port valve N.O. + N.O.Dual 3 port valve N.C. + N.O.

Type of actuation

Note 1) The function symbol is "D" for double solenoid specifications.

Note 2) Available only for rubber seal type.

Symbol Cylinder port size SQ1000

——

SQ2000——

Pipingspecifications

Sideported

Topported

C3C4C6C8L3L4L6L8

With One-touch fitting for ø3.2With One-touch fitting for ø4With One-touch fitting for ø6With One-touch fitting for ø8With One-touch fitting for ø3.2With One-touch fitting for ø4With One-touch fitting for ø6With One-touch fitting for ø8

Cylinder port size

Note) Inch sizes use the following symbols. N1: ø1/8" (SQ1000 only) N3: ø5/32" N7: ø1/4" N9: ø5/16" (SQ2000 only)

Symbol

Nil

B Note)

D Note)

Specifications

Non-locking push type (tool required)

Slotted locking type (tool required)Slide locking type (manual type)

SQ1000

—

SQ2000

Manual operation

Options

P, R port inch bore size

… …

Symbol SeriesSQ1000SQ2000

12

The solenoids are counted asSingle : 1 pointDouble, 3P: 2 pointsDual 3 port : 2 points

Manifold mountingSymbol Mounting

DIN rail mount typeDirect mount type

DE

How to Order Valves

Series

SQ 3

SQ1000SQ2000

12

Coil voltageSymbol Voltage

24VDC5

SymbolNilAB

SpecificationsNoneA portB port

Port plug mounting port

SymbolNil Note 1)

M Note 2)

MB Note 2)

SpecificationsWithout manifold block

With manifold block

With manifold blockBuilt-in back pressure check valve

Manifold block

Note) Except double (latching)

1 08 D N

1 1 1 Y 5 B C6

Set the maximum number of stations so that there are no more than 16 solenoids for 9 or more stations. Note 1) In case of two or more options, enter in alphabetical order.

Example: –D12BSNote 2) Indicate DIN rail length as “D ( indicates stations)”.

Example: –D08In this case, an eight station DIN rail will be provided regardless of the number of manifold stations.

Note 3) Indicate wiring specifications on a manifold specification sheet.

Note) The light/surge voltage suppressor is built-in.

Note 1) • When ordered with manifold • When only valve is required

Note 2) • For station additions

Series SQ1000/2000

19

Series ModelResponse time msStandard:

1WLow

power

Effective areamm²

(Cv factor)

Weightg

Numberof

solenoids

SQ

1000

Single

Double (latching)

Double (double solenoid)

Closedcenter

Exhaustcenter

Pressurecenter

Dual3 port valve

Single

Double (latching)


Closedcenter

Exhaustcenter

Pressurecenter

Dual3 port valve

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Rubber seal

SQ1130

SQ1131

SQ1230

SQ1231

SQ1230D

SQ1231D

SQ1330

SQ1331

SQ1430

SQ1431

SQ1530

SQ1531

SQ2130

SQ2131

SQ2230

SQ2231

SQ2230D

SQ2231D

SQ2330

SQ2331

SQ2430

SQ2431

SQ2530

SQ2531

3.2 (0.18)

4.5 (0.25)

3.2 (0.18)

4.5 (0.25)

3.2 (0.18)

4.5 (0.25)

2.9 (0.16)

3.2 (0.18)

3.2 (0.18)

4.5 (0.25)

2.9 (0.16)

3.2 (0.18)

3.2 (0.18)

11.7 (0.65)

14.8 (0.82)

11.7 (0.65)

14.8 (0.82)

11.7 (0.65)

14.8 (0.82)

8.1 (0.45)

9.0 (0.5)

11.7 (0.65)

12.6 (0.7)

8.1 (0.45)

9.0 (0.5)

9.0 (0.5)

12 or less

15 or less

15 or less

20 or less

10 or less

15 or less

20 or less

25 or less

20 or less

25 or less

20 or less

25 or less

25 or less

20 or less

24 or less

26 or less

31 or less

15 or less

20 or less

34 or less

34 or less

34 or less

34 or less

34 or less

34 or less

34 or less

15 or less

20 or less

—

—

13 or less

20 or less

26 or less

33 or less

26 or less

33 or less

26 or less

33 or less

33 or less

26 or less

31 or less

—

—

20 or less

26 or less

44 or less

44 or less

44 or less

44 or less

44 or less

44 or less

44 or less

80

80

80

80

95

95

100

100

100

100

100

100

95

145

140

145

140

160

155

180

175

180

175

180

175

155

SQ1 31

2 p

osi

tion

3 p

osi

tion

4p

osi

tion

SQ

2000

2 p

osi

tion

3 p

osi

tion

Models

Valve construction

Fluid

Maximum operating pressure

Single

Double (latching)


3 position

4 position

Minimumoperatingpressure

Metal seal

0.1MPa

0.18MPa

0.1MPa

0.1MPa

—

Rubber seal

0.15MPa

0.18MPa

0.1MPa

0.2MPa

0.15MPa

Note) Value for the low power consumption (0.5W) specification

Ambient and fluid temperature

Lubrication

Manual operation

Impact/Vibration resistance

Enclosure

Solenoid SpecificationsRated coil voltage

Allowable voltage fluctuation

Coil insulation type

Power consumption(current value)

24VDC

±10% of rated voltage

Class B equivalent

DC1W (42mA)

DC0.5W (21mA) Note)

–10 to 50°C Note 1)

Not required

Push type/Slotted locking type (tool required)

30/150m/s²

Dust proof

0.7MPa (High pressure type: 1.0MPa)

Standard Specifications

ABC

SQ2 31ABC

Base type

Ser

ies

Applicablesolenoid

valve

Applicablestations

5stationweight

g

Additionalweight

of1 station

g

Type ofconnection

J kit: Flat cable

1 to 8 stations

1 to 8stations

420

580

20

35J kit: Flat cable

Piping specifications

Port size

P, RA, B

Piping

Side

Top

Side

Top

Port size

SQ

1000

SS5Q13- -

SQ

2000

SS5Q23 -

C8(for ø8)

OptionBuilt-insilencerDirect

exhaust

C3 (for ø3.2)

C4 (for ø4)

C6 (for ø6)

L3 (for ø3.2)

L4 (for ø4)

L6 (for ø6)

C4 (for ø4)

L6 (for ø6)

C8 (for ø8)

L4 (for ø4)

C6 (for ø6)

C8 (for ø8)

SQ130SQ131

SQ230SQ231

Manifold Specifications

OptionBuilt-inSilencerDirect

exhaust

C10(for ø10)

Note 2)

Note 1)

Note 3) Note 4) Note 4)

Note 2)

Note 1) Note 2)

24VDC

Air, Inert gasNote 3)

Note 2)

4p

osi

tion

Note 1) SQ1000 values are for cylinder port size C6.SQ2000 values are for top ported type with cylinder port size C8. Side ported type is approximately 10% smaller.

Note 2) Based on JISB8375-1981 (Values for supply pressure of 0.5MPa with light/surge voltage suppressor. This will change depending on pressure and air quality.)

Note 1) One-touch fittings for inch sizes are also available.Note 2) Side ports can be changed.Note 3) The maximum number of stations can be expanded with optional special

wiring specifications.Note 4) Except valve weight

Note 1) In case of low temperature, use dry air with no condensation.Note 2) Vibration resistance…No malfunction when tested with one sweep of 8.3

to 2000Hz in the axial direction and at a right angle to the main valve/armature, one time each with and without current. (initial values)

Impact resistance….. No malfunction when tested with a drop and impact tester in the axial direction and at a right angle to the main valve/armature, one time each with and without current. (initial values)

Note 3) SQ1000 metal seal type only except double (latching)

20

5 Port Solenoid Valve Series SQ1000/2000

SQ1000/Flat Cable Kit

L1L2L3L4

L n 167

84.5112.5123

4101.5119 150 160.5

5113 130.5150 160.5

6124.5142 162.5173

7136 153.5175 185.5

8147.5165 187.5198

9159 176.5200 210.5

10170.5188 212.5223

11182 199.5225 235.5

12193.5211 237.5248

13205 222.5250 260.5

14216.5234 262.5273

15228 245.5275 285.5

16239.5257 287.5298

390

107.5137.5148

2 78.5

96125 135.5

Dimensions Formulae L1 = 11.5n + 55.5 L2 = 11.5n + 73 n: Stations (max. 16 stations)

StationsSS5Q13- JD0

D side U sideStation 1 2 3 4 5 6 7 8 n

2.PUSH

1.TURN

2.PUSH

1.TURN

2-M4 clamping screw

AA A B A BA

B

22222222

4

R

P

3

1

4 4 4 4 4 4 4

49.547

Applicable connector: Flat cable connector (20P)(conforms to MIL-C-83503)

Triangle markindicator position

EXH. outlet

M5: External pilot port

5.25

1.5

47.8

L1

L2

L3

L4

10.3

P = 11.5 19.2

1.5

Indicator light

Manual override

Release for switching connector direction

C8: R(EXH) port

C8: P(SUP) port

For top ports

2n-C3, C4, C6A, B port

25

(10

8.5)

122

(3 p

ositi

on)

113

dou

ble

(dou

ble

sole

noid

) dua

l 3 p

ort v

alve

108.

5 s

ingl

e, d

oubl

e (la

tchi

ng)

App

rox.

10

App

rox.

9

94

3410 4.

6

43.558 P = 11.5

74.5

13

28

5.5

35

13

29.5

26

3760

App

rox.

9

20.5(mounting hole dimension)

Series SQ1000/2000

21

SQ2000/Flat Cable Kit

L1L2L3L4

L n 1 69.592

112.5123

4122 144.5175 185.5

5139.5162 187.5198

6157 179.5200 210.5

7174.5197 225 235.5

8192 214.5237.5248

9209.5232 262.5273

10227 249.5275 285.5

11244.5267 287.5298

12262 284.5312.5323

13279.5302 325 335.5

14297 319.5350 360.5

15314.5337 362.5373

16332 354.5375 385.5

3104.5127 150 160.5

2 87 109.5137.5148

Dimensions Formulae L1 = 17.5n + 52 L2 = 17.5n + 74.5 n: Stations (max. 16 stations)

StationsSS5Q23- JD0

D side U sideStation 1 2 3 4 5 6 7 8 n

44.563.5 P = 17.5

A A AB AB AB AB AB AB

4 A

2 B4A

B2

4A

B2

4A

B2

4A

B2

4A

B2

4A

B2

4A

B2

4A3

1

R

PB2

5825

Indicatorlight

Manualoverride

2-M4clampingscrew

L128.8

L2

L3L4

5.25

147.8 P = 17.5

M5: External pilot port

Triangle markindicator position

EXH. outlet

C10: R(EXH) portFor top ports

2n-C4,C6,C8A, B port

C10: P(SUP) port

Release for switching

connector direction

Applicable connector:Flat cable connector (20P) (conforms to MIL-C-83503)

(13

1.5)

5.5

5.5

3547

.556

SM

C

122.

3

131.

5 (s

ingl

e, d

oubl

e, d

ual 3

por

t val

ve)

147

(3 p

ositi

on)

10.4

Appr

ox. 1

2

18.5

37.6 53

.6

21

39.5 (

58) 62

41.5

25.5

App

rox.

10

18 (mounting hole dimension)

Appr

ox. 1

2

22

5 Port Solenoid Valve Series SQ1000/2000

D

B C6

FE

1. How to Order Manifolds

SS5Q J1 3 08 D0 N ( 00T)

For P, R port inch sizeKit designation

Plug-inSeries VQ1000

Stations01

…

1 station

16 16 stations

…

Electrical entry/Cable length OptionsNil None

Specifies DIN rail length Note 2)

With back pressure check valve on all stationsSpecial wiring specifications (except double wiring) Note 3)

With name plate (valve with side port specification only) External pilot specificationBuilt-in silencer

02 to 24BKNRS

Kitdesignation

J

Entrydirection

JD0 D sideFlat cable (20P) kit for PC wiring system

Without cable

StandardstationsKit, Cable length

1 to 8 (16)

1

1

2

2

4

D

3

2. How to Order Applicable Valves

SQ 1 3 51 Y1

Series SQ1000C HGB

B

A

A

12 Note 1)

345

A Note 2)

B Note 2)

C Note 2)

Manual operationNil

B Note 1)

Non-locking push type (tool required) Slotted locking type (tool required)

Cylinder port sizeWith One-touch fitting for ø3.2 With One-touch fitting for ø4With One-touch fitting for ø6With One-touch fitting for ø3.2With One-touch fitting for ø4With One-touch fitting for ø6

C3C4C6L3L4L6

Type of actuation

01

E

F

Manifold Specification Sheet

Series SQ1000/Plug-in Unit

Manifold mountingDE

DIN rail mount typeDirect mount type

3

G Port plug mounting portNilAB

NoneA portB port

D Coil voltage5 24VDC

C FunctionStandard type (1W) 2 position double (double solenoid specification)

High pressure type(1.0MPa, 1W) available only for metal seal

Negative commonLow power consumption type (0.5W) External pilot specifications

NilD

K Note 1)

NY Note 1)

R Note 2)

Manifold blockH

A A A A B A B2.PUSH

1.TURN

2.PUSH

1.TURN

D side Station 1 2 3 4 5 n U side

Nil Note 1)

M Note 2)

MB Note 2)

Without manifold blockWith manifold block


Note 2)

Note 1) Except double (latching)

Sid

epo

rted

Top

port

ed

∗ ) Stations are counted starting from station 1 on the D side.

2 position single2 position double (latching/double solenoid) 3 position closed center3 position exhaust center3 position pressure centerDual 3 port valve N.C. + N.C.Dual 3 port valve N.O. + N.O.Dual 3 port valve N.C. + N.O.


Seal type

Note 1) Except double (latching) typeNote 2) Except dual 3 port valveNote 3) When specifying more than one option, enter

symbols in alphabetical order.

Note) Inch sizes use the following symbols.• N1: ø1/8˝• N3: ø5/32˝• N7: ø1/4˝Top ports are indicated by LN.

Note 1) Order cable assembly separately.Note 2) Numbers inside ( ) indicate the maximum number of solenoid stations for

mixed single/double wiring. The maximum number of stations is determined by the total number of solenoids. When ordering mixed wiring, add the option symbol "-K". Note 1) In case of two or more options, enter in alphabetical

order.Example: –D12BS

Note 2) Indicate DIN rail length as “D”. ( indicates stations) Example: –D08In this case, an eight station DIN rail will be provided regardless of the number of manifold stations.

Note 3) Be sure to indicate wiring specifications on a specification sheet.

Note 1) The function symbol is “D” for double solenoid specifications.

Note 2) Available only for rubber seal type



Note 2) • For station addition

4

23



Manifold Models

SS5Q JD01 3DE

(Circle the applicable item)

BABABABABABABABABABABABABABABABA

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

StationDescription/Model

Note 4)

Note 3)

Single

Double(latching)

Double(double solenoid)

Closed center

Pressure center

Exhaust center

Dual 3 port valve (A)

Dual 3 port valve (C)

Dual 3 port valve (B)

SUP block bushingSSQ1000-B-P

Back pressure check valve Note 1) SSQ1000-BP

Blanking plateSSQ1000-10A-3Supply/Exhaust blockSSQ1000-PR-3-C8- (S)

EXH block bushingSSQ1000-B-R

Port plug Note 2)

For ø3.2 (ø1/8˝) With One-touch fittingFor ø4 (ø5/32˝) With One-touch fittingFor ø6 (ø1/4˝) With One-touch fitting

C3 (N1)

P

R

C4 (N3)

C6 (N7)

Special wiringspecifications

Single wiring

Double wiring

Val

ves

Op

tion

sC

ylin

der

po

rt s

izes


Specifications D side← U side →∗ Enter an “X” in the required locations.

Company name

Contact person

Specification sheet no.

Purchase order no.

Equipment name

Quantity set(s) Required date

Date / /

Part no. Qty. Part no. Qty.

Applicable valves and options

∗ Copy this page for use as needed.

Order no.

Clerk (code no.)

Dept. code

N.C. N.C.

4 2

15 3

4 2

15 3

4 2

15 3

4 2

1 5 3

4 2

1 5 3

4 2

15 3

4 2

15 3

4 2

15 3

4 2

15 3

N.O. N.O.

4 2

1

N.C. N.O.1

5 3

4 2

5 3

Metal Rubber

Metal Rubber

SMC use only

Notes

Note 1) When installing on all manifold stations, use "B" for the manifold part number option symbol. When installing only on required station positions, specify the part number and indicate the station positions on the specification sheet.

Note 2) When using port plugs, circle the specified ports.

Note 3) In case of single wiring or mixed wiring, connections to the connector terminals start from the A side solenoid of station 1 and continue in order without skipping any terminals.

Note 4) In case of valves with top port specifications, enter "L" in the specification table.

24

FunctionStandard type (1W)2 position double (double solenoid specification)Negative commonLow power consumption type (0.5W)External pilot specification

Note 1) Except double (latching) typeNote 2) Except dual 3 port valveNote 3) When specifying two or more options, enter

symbols in alphabetical order

D

B C6

FE


SS5Q J2 3 08 D0 N ( 00T)

For P, R port inch sizesKit designation

Plug-inSeries VQ2000

Stations01

…

1 station

16 16 stations

… 02 to 24BKNRS

1

1

2 4

D

3

4


SQ 2 3 51 Y1

Series SQ2000C GB

B

A

A1

2 Note 1)

345

A Note 2)

B Note 2)

C Note 2)

Manual operationNil Non-locking push type (tool required)

Slotted locking type (tool required)Slide lock type (manual): Available only with side ports

B Note 1)

D Note 1)

Cylinder port sizeWith One-touch fitting for ø4With One-touch fitting for ø6With One-touch fitting for ø8With One-touch fitting for ø4With One-touch fitting for ø6With One-touch fitting for ø8

C4C6C8L4L6L8

01

E

F

Note) Inch sizes use the following symbols.• N3: ø5/32˝• N7: ø1/4˝• N9: ø5/16˝Top ports are indicated by LN.



DE

3

D Coil voltage5 24VDC

C

NilDN

Y Note 1)

R Note 2)

B AA A B AB A

D side Station 1 2 3 4 5 n U side

G

J JD0 D side Flat cable (20P) kit for PC wiring system Without cable

1 to 8 (16)

2 Note 2)

Note 1) Except double (latching)


Note 2) • For station addition

NoneSpecifies DIN rail length Note 2)

With back pressure check valve on all stationsSpecial wiring specifications (except double wiring) Note 3)

With name plate (valve with side port specification only)External pilot specificationBuilt-in silencer

OptionNil

Electrical entry/Cable lengthKit

designationEntry

directionStandardstationsKit, Cable length

Manifold mountingDIN rail mount typeDirect mount type

Type of actuation2 position single2 position double (latching/double solenoid)3 position closed center3 position exhaust center3 position pressure centerDual 3 port valve N.C. + N.C.Dual 3 port valve N.O. + N.O.Dual 3 port valve N.C. + N.O.


Seal type

Sid

epo

rted

Top

port

ed

Manifold blockWithout manifold block

With manifold block


Nil Note 1)

M Note 2)

MBNote 2)

Note 1) Order cable assembly separately.Note 2) Numbers inside ( ) indicate the maximum number of solenoids for mixed

single/double wiring. The maximum number of stations is determined by the total number of solenoids.In case of mixed wiring, add the option symbol "-K". Note 1) In case of two or more options, enter symbols in alphabetical order.

Example)-D12BS

Note 2) Indicate DIN rail length as “D”. ( indicates stations)Example: –D08In this case, an eight station DIN rail will be provided regardless of the number of manifold stations.



Note 1) The function symbol is “D” for double solenoid specifications.

Note 2) Available only for rubber seal type

∗ ) Stations are counted starting from station 1 on the D side.

25



Manifold Models

SS5Q JD02 3DE

(Circle the applicable item)


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


Note 4)

Note 3)

Single

Double(latching)

Double(double solenoid)

Closed center

Pressure center

Exhaust center

Dual 3 port valve (A)

Dual 3 port valve (C)

Dual 3 port valve (B)

SUP block bushingSSQ1000-B-R

Back pressure check valve SSQ2000-BP

Blanking plateSSQ2000-10A-3Supply/Exhaust block Note 1)

SSQ2000-PR-3-C10- (S)

EXH block bushingSSQ2000-B-R

Port plug

For ø4 (ø5/32˝) With One-touch fittingFor ø6 (ø1/4˝) With One-touch fittingFor ø8 (ø5/16˝) With One-touch fitting

C4 (N3)

P

R

C6 (N7)

C8 (N9)


Single wiring

Double wiring

Val

ves

Op

tion

sC

ylin

der

po

rt s

izes


Specifications D side← U side →∗ Enter an “X” in the required locations.

Company name

Contact person


Purchase order no.

Equipment name


Date / /

Part no. Qty. Part no. Qty.



Order no.

Clerk (code no.)

Dept. code

N.C. N.C.

4 2

15 3

4 2

15 3

4 2

15 3

4 2

1 5 3

4 2

1 5 3

4 2

15 3

4 2

15 3

4 2

15 3

4 2

15 3

N.O. N.O.

4 2

1

N.C. N.O.1

5 3

4 2

5 3

Metal Rubber

Metal Rubber

SMC use only

Notes

Note 1) When installing on all manifold stations, use "B" for the manifold part number option symbol. When installing only on required station positions, specify the part number and indicate the station positions on the specification sheet.

Note 2) When using port plugs, circle the specified ports.

Note 3) In case of single wiring or mixed wiring, connections to the connector terminals start from the A side solenoid of station 1 and continue in order without skipping any terminals.

Note 4) In case of valves with top port specifications, enter "L" in the specification table.

26

27

Series


2 position 3 position 4 position One-touch fitting

SZ360

Effective areamm²

(Cv factor)

3.7 (0.21)

Sin

gle

Dou

ble

Clo

sed

cent

er

Exh

aust

cen

ter

Pre

ssur

e ce

nter

Dua

l3

port

val

ve

M5C4L4

(ø4)

C6L6

(ø6)

• Size and weight reductions have been realized by eliminating the manifold base

• The plug-in cassette system makes valve replacement easy• A plug-in manifold has been achieved with a height of

43.5mm (including DIN rail)• Valves with switches are available to allow each valve to be

turned off individually• 4 position dual 3 port valve provided by combining two 3

port valves in one valve body• Valve with back-pressure check function available• Low power consumption: 0.65W (with light)

(Current value: 27mA, 24VDC)

28

Rubber Seal 5 Port Solenoid Valve

Series SZ3000

Supply/Exhaust blockassembly mounting position

SS5Z3—60GD — —U1 05Connector entry direction

Connector vertical

Connector horizontal

UDBM∗

Options

Valve stations

Nil

R

Double wiring specification

Specified wiring(up to 16 solenoids

are possible)

NoteSymbol

02

0802

16

12

……

Stations

2 stations

8 stations

2 stations

16 stations

……

Note 1) Double wiring specifications: Single, double, 3 position and 4 position solenoid valves can be used at all of the manifold stations.

Specified layout: Indicate the wiring specifications on a manifold specification sheet.(Please note that in locations where single solenoid wiring is indicated, it will be impossible to use double or 3 and 4 position valves.)

Note 2) The number of blanking blocks is also included.


Supply/Exhaust block assemblyfitting specifications

Straight

Elbow fitting (upward)

Elbow fitting (downward)

Nil

LB

How to Order Valves

Non-lockingpush type

Nil

J

Without switch

With switch

Slottedlocking type

SZ3 — — 51 C6LOZ 60Type of

actuation

12345ABC

2 position single solenoid

2 position double solenoid

3 position closed center

3 position exhaust center

3 position pressure center

4 position dual 3 port valve: N.C./N.C.

4 position dual 3 port valve: N.O./N.O.

4 position dual 3 port valve: N.C./N.O.

Rated voltage 5

C4C6M5L4L6B4B6

Nil

D

24VDC

Pilot specificationsInternal pilot

External pilot

Nil

R

Switchspecifications

Manual override

A, B port sizeø4 One-touch fitting

ø6 One-touch fitting

M5 x 0.5

ø4 elbow fitting assembly (upward)

ø6 elbow fitting assembly (upward)

ø4 elbow fitting assembly (downward)

ø6 elbow fitting assembly (downward)

Back pressure check valveNone

Built-in

Nil

K

Note 1) The effective area is reduced by about 20% for the built-in back pressure check valve type.

Note 2) 3 position closed center and 3 position pressure center are not available with back pressure check valve.

Note) 4 position dual 3 port valves are not available with external pilot specification.

How to Order ManifoldAssemblies (Example)Example (SZ3000, positive commonwith power supply terminals)

SS5Z3-60GD2-05U ...1 set (manifold part number)

∗ SZ3160-5LOZ-C6 ... 2 sets (single solenoid part number)

∗ SZ3260-5LOZ-C6 ..... 3 sets (double solenoid part number)

Double solenoid

SZ3260-5LOZ-C6 (3 sets)

Single solenoid

SZ3160-5LOZ-C6 (2 sets)

Manifold SS5Z3-60GD2-05U

Supply/Exhaust block(U side mounting)

12

3Statio

n

D side

U side

FREE

LOCK

U Side (2 to 10 stations)

D Side (2 to 10 stations)

Both sides (2 to 16 stations)

Special specifications

∗ For special specifications, indicate them separately on a manifold specification sheet.

Note) A total of up to 3 supply/exhaust blocks can be mounted. Contact SMC if 4 or more will be mounted.

Pilot specificationsInternal pilot specification


The "∗ " symbol indicates mounting. Put the "∗ " symbol at the beginning of part numbers for solenoid valves, etc., which are to be mounted.

• Valve stations are numbered from station 1 on the D side.

• Indicate the valves to be mounted below the manifold part number, in order starting from station 1 as shown in the drawing. When a layout becomes complicated, please indicate on a manifold specification sheet.

When a DIN rail is required that is longer than the standard types, specify the number of stations. (max. 20 stations)

Series SZ3000

29

A, B port piping specifications

Port size

Valveeffectivesectional area mm²

(Cv factor)

P→A/B

A/B→R

P→A/B

A/B→R

Flat cable type 60G

Plug-in type

Common SUP, EXH

Valve

Side

C8

C4, C6, M5

3.4 (0.19) [3.0 (0.17)]

3.2 (0.18) [3.2 (0.18)]

3.7 (0.21) [3.2 (0.18)]

3.9 (0.22) [3.8 (0.21)]

3.4 (0.19) [3.2 (0.18)]

3.2 (0.18) [3.2 (0.18)]

2 to 16 stations

Weight W (g) Note 3)

n1: Stationsn2: Number of supply/exhaust blocksm : Weight of DIN rail

P→A/B

A/B→R

Location

Direction

C4

C6

M5

P, R ports

A/B ports

Model

Manifold type

P (SUP), R (EXH) system

Valve stations Note 1)


W = 3.2n1 + 53n2 + m + 126.5

Note 2)

Series

Fluid

2 position single

2 position double

3 position

4 position dual 3 port valve

2 position single

2 position double

3 position

2 position single, double4 position dual 3 port valve

3 position

Internal pilotoperatingpressurerangeMPa

External pilot operatingpressure rangeMPa

Pilot pressure range

Operating pressure range

Air

0.15 to 0.7

0.1 to 0.7

0.2 to 0.7

0.15 to 0.7

-100kPa to 0.7

0.25 to 0.7

Maximum 50

3

Non-locking push type, Slotted locking type

Main valve, pilot valve common exhaust type

Not required

Unrestricted

150/30 (8.3 to 2000Hz)

Dust proof

SZ3000

Ambient and fluid temperature °C

Maximumoperatingfrequency Hz

Manual override

Pilot system

Lubrication

Mounting orientation

Impact/Vibration resistance m/s2 Note)

Enclosure

Solenoid SpecificationsL type (for plug-in)

24VDC


0.65W

Diode

LED

Weights

Response Time

Type of actuation

Response time ms

2 position single2 position double3 position4 position dual 3 port valve

With light/surge voltage suppressor

15 or less13 or less20 or less35 or less

Valve model Type of actuationPort size

A, B

M5 x 0.8

SZ360--C4

SZ360--C6

SZ360--M5

2 position

Weight g

77.183.7

87.6

8473.580.2

84.1

8168.375

78.8

75

3 position

4 position

4 position

4 position

2 position

3 position

2 position

3 position

SingleDouble

Closed centerExhaust centerPressure center

Dual 3 port valveSingleDouble


Dual 3 port valveSingleDouble


Dual 3 port valve

C4ø4 One-touch

fitting

C6ø6 One-touch

fitting

10

Solenoid Valve Specifications

Note) Impact resistance: No malfunction when tested with a drop tester in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states. (Initial value)

Vibration resistance: No malfunction when tested with one sweep of 8.3 to 2000Hz in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states. (Initial value)

Electrical entry

Rated coil voltage


Power consumption

Surge voltage suppressor

Indicator light

Note 1) Available with up to 16 solenoids. When a large number of valves will be operated simultaneously, use type B (supply/exhaust on both sides), applying pressure to the P ports on both sides and releasing exhaust from the R ports on both sides.

Note 2) • The value is for manifold base mounting (5 stations). 2 position type with single action.

• Values inside [ ] are for 4 position dual 3 port valves. Furthermore, when the A and B sides of a 4 position dual 3 port valve are operated simultaneously, the Cv factor will be about 35% less than in the table above.

• The Cv factor for valves with back pressure check valve will be about 20% less than in the table above.

Note 3) The weight W is the value for the manifold only. To obtain the weight with solenoid valves, add the solenoid valve weights for the required number of stations. Refer to the separate catalog ES11-75B regarding DIN rail weight.

Note) Based on JISB8375-1981 dynamic performance test (with coil temperature of 20°C and at rated voltage).

30

Cassette Type Manifold Series SZ3000

[With external pilot]

Dimensions/SZ3000: Plug-in

L1L2L3L4

L n 2110.5100 81 15

5148 137.5112.518

6148 137.5123 12.5

7160.5150 133.5 13.5

8173 162.5144 14.5

9185.5175 154.5 15.5

10198 187.5165 16.5

4135.5125 102 17

3123 112.5 91.516

Internal pilot manifold L: Dimensions n: Stations (n1 + n2)

L1L2L3L4

L n 2123 112.5 91.516

5148 137.5123 12.5

6160.5150 133.5 13.5

7173 162.5144 14.5

8185.5175 154.5 15.5

9198 187.5165 16.5

10210.5200 175.5 17.5

4148 137.5112.518

3135.5125 102 17

External pilot manifold L: Dimensions n: Stations (n1 + n2)

StationsSS5Z3-60GD U--12

A4X

B2

A4

B2

A4

B2

A4

B2

A4

B2PE

P1

R3

24

16.2

34

13.3

2-One-touch fitting(X, PE port)Applicable tube O.D.: ø6

6

7.9

36.147

.6Triangle mark position

Triangle mark

4 A

B2

4 A

B2

4 A

B2

4 A

B2

4 A

B2

1 P

R3

2-One-touch fitting[1(P), 3(R) port]Applicable tube O.D.: ø8

2n1-M5 x 0.8[4(A), 2(B) port]24

34

17

36.716

.2

13.3

2n2-One-touch fitting[4(A), 2(B) port]Applicable tube O.D.: ø4, ø6

5.5

35

5.3 36

.358

.2

101.

2(3

.2)

3.5

(With

sw

itch)

6.6

8

L2(Rail mounting hole pitch 12.5)

22

5

3.1

18

28.8

DIN rail

DIN rail holding screw

L3

L1

(L4)

Manual override

Power supply terminals(M3 terminal screws)

Connector entrydirection switch

Applicable connector: 26 pin MIL typewith strain relief

(conforms to MIL-C-83503)

AAAB

AB

A

OFF

ON

OFF

ON

LOC

KF

RE

E

U side D side

(Pitch)P = 10.5

4 (A): Orange2 (B): Green

In case of locking type, turn after pushing in. ( )

(Station n)........(Station 1)Light/Surge voltage suppressor

Side A: OrangeSide B: Green

Switch(when equipped with switch)

43.5 (6

2.4)

34.2

18.9

(7.5

)

(DIN

rail d

imen

sion)

31

Series SZ3000

[With external pilot]

L1L2L3L4

L n 2135.5125 107.514

3148 137.5118 15

4160.5150 128.516

5173 162.5139 17

6173 162.5149.512

7185.5175 160 13

8198 187.5170.514

9210.5200 181 15

10223 212.5191.516

11235.5225 202 17

12248 237.5212.518

13248 237.5223 12.5

14260.5250 233.5 13.5

15273 262.5244 14.5

16285.5275 254.5 15.5

Dimensions/SZ3000: Plug-inStationsSS5Z3-60GD B--1

2

External pilot manifold L: Dimensions n: Stations (n1 + n2)

L1L2L3L4

L n 2123 112.597 13

3135.5125 107.514

4148 137.5118 15

5160.5150 128.516

6173 162.5139 17

7173 162.5149.512

8185.5175 160 13

9198 187.5170.514

10210.5200 181 15

11223 212.5191.516

12235.5225 202 17

13248 237.5212.518

14248 237.5223 12.5

15260.5250 233.5 13.5

16273 262.5244 14.5

Internal pilot manifold L: Dimensions n: Stations (n1 + n2)

5

6

7.9

36.1

47.6

Triangle mark

24

16.2

34

13.3

2-One-touch fitting(X, PE port)Applicable tube O.D.: ø6

Triangle mark position

Applicable connector: 20 pin MIL typewith strain relief


A4

B2

A4

B2

A4

B2

A4

B2

A4

B2

P1

R3

P1

R3

4-One-touch fitting[1(P), 3(R) port]Applicable tube O.D.: ø8

2n-One-touch fitting[4(A), 2(B) port]Applicable tube O.D.: ø4, ø6

24

36.7 16

.2

34

17

13.3(Pitch)P = 10.5

2n1-M5 x 0.8[4(A), 2(B) port]

(3.2

)10

1.2

5.5

35

5.3 36

.3

3.1

58.2

6.6

8

L2(Rail mounting hole pitch 12.5)

22

18

28.8

L3

L1

(L4)

Manual override

4 (A): Orange2 (B): Green

Connector entrydirection switch

DIN rail

DIN rail holding screw

3.5

(With

sw

itch)

AB

AAB

AA

B

A4

2

A4

B

A4

2B

A4

2B

A4

2

1

3

P

R

X

PE

1

3

P

RB2

OFF

ON

OFF

ON

LOC

KF

RE

E

U side D side

Switch(when equipped with switch)

Light/Surge voltage suppressor

A side: OrangeB side: Green

Power supply terminals(M3 terminal screws)

In case of locking type,turn after pushing in.( )

43.5 (6

2.4)

34.2

(7.5

)

(DIN

rail d

imen

sion)

(18.9)

(Station n)........(Station 1)

32

Cassette Type Manifold Series SZ3000

set(s) Date required

Supply/Exhaust block assembly mounting position

SymbolUDB

Applicable stations2 to 10 stations2 to 10 stations2 to 16 stations

Mounting positionU sideD side

Both sides

C A, B port sizeC4C6M5L4L6B4B6M

ø4 One-touch fittingø6 One-touch fittingM5 x 0.8ø4 elbow One-touch fitting (upward) ø6 elbow One-touch fitting (upward) ø4 elbow One-touch fitting (downward) ø6 elbow One-touch fitting (downward) Mixed

Nil

D

SZ3000: Cassette TypePlug-in Manifold

Please copy this page for use without removing it.

Manifold Valve Specification Sheet

Make entries in order from to .

Enter the symbols for the required specifications in the blanks below.

SS5Z3-60GD

SS5Z3-60GD M


SZ3 ∗ 60 ∗ ∗ 5LOZ

For SMC use only

20 19 18 17 16 15 13 12 1114 10 9 8 7 6 5 4 3 2 1 Quantity

Part no. QuantityPart no. Quantity Order no.

Clerk (code no.)

Dept. code

a

d

e

f

b

c

Valve stations or layoutSingle solenoidDouble solenoidClosed centerExhaust centerPressure centerSZ3A60 (N.C., N.C.) SZ3B60 (N.O., N.O.) SZ3C60 (N.C., N.O.)

External pilot specification (enter only in case of external pilot)

Back pressure check valve (enter only in case of back pressure check valve)

SUP blocking diskEXH blocking diskPilot port blocking disk

Enter forspecialspecs.

Wiring specifications

Single wiringDouble wiring

Supply/Exhaust block assemblyExternal pilot block assembly

2 position

3 position

4 positiondual

3 port valve

Blanking block assembly

B

Type of valve actuation

Manual override

Enter an “X” for the manifold type to be used.

A B C

Valve stations SpecialspecificationsIndicate the supply/exhaust blockand external pilot block postion in section (d) of the station table below.

• In case of R, external pilot block will be added.

SymbolNilR

Pilot systemSpecifications

Standard/internal pilot specificationExternal pilot specification

Symbol02

16

Stations2 stations

16 stations

......

Connector entry directionSymbol

12

Mounting positionVertical

Horizontal

ANilJ

2 position single solenoid2 position double solenoid3 position closed center3 position exhaust center3 position pressure center4 position dual 3 port valve (N.C., N.C.) 4 position dual 3 port valve (N.O., N.O.) 4 position dual 3 port valve (N.C., N.O.)

12345ABC

Indicate in the station table below.

Pilot typeNilR

Internal pilotExternal pilot

Enter the ordered part numbers.

• Supply/Exhaust block assembly (ø8): SZ3000-50-1A-C8• Supply/Exhaust block assembly (ø6): SZ3000-50-1A-C6• External pilot block assembly (ø6): SZ3000-54-1A-C6• External pilot block assembly (ø4): SZ3000-54-1A-C4

Note) The final symbol indicates the port size for supply/exhaust block and external pilot block assemblies.

• Supply/Exhaust block assembly (elbow upward): SZ3000-50-1A-L6/L8• Supply/Exhaust block assembly (elbow downward): SZ3000-50-1A-B6/B8• External pilot block assembly (elbow upward): SZ3000-54-1A-L4/L6• External pilot block assembly (elbow downward): SZ3000-54-1A-B4/B6

1 How to Order Manifolds

2 How to Order Valves

3 Station Table

Supply/Exhaust block assembly fitting specifications

Nil StraightElbow One-touch fitting (upward) Elbow One-touch fitting (downward)

SpecificationsSymbol

LB

Indicate the layout of valves, etc., with "X's".• When the port sizes of each block assembly are mixed or special specifications, indicate them by entering the port size symbols (C4, C6, etc.).

Back pressure check valveNilK

NoneBulit-in

Special specifications

Standard type

n

Supply/Exhaustblock assembly

D side U side

m

AB

AAA AB

LOC

KF

RE

E

Company name

Contact person


Purchase order no.

Equipment name

Quantity

Date / /

OptionsWhen a DIN rail is required that is longer than

the standard types, specify the number of stations.

(max. 20 stations)

Valve stationsLayout

(for special specifications) Switch specificationsWithout switchWith switch

Non-locking push type

Slotted locking type

Note) When there are special specifications, enter part numbers and quantities for supply/exhaust block and external pilot block assemblies together with the manifold type.

When an external pilot valve is to be used, enter an "X" in section (b) of the station table below.However, external pilot specifications are not available for 4 position dual 3 port valves.

When a valve with back pressure check valve is used, enter an "X" in section (c) of the station table below.

[Note] • SUP blocking disk: SZ3000-114-4A • EXH blocking disk: SZ3000-114-4A (2pcs./location) • Blanking block assembly: SZ3000-55-1A• Pilot port blocking valve: SZ3000-114-2A

33

Series


2 position 3 position One-touch fitting

SX340

SX540

Effective areamm2

(Cv factor)

4.68 (0.26)

12.6 (0.7)

—

Sin

gle

Dou

ble

Clo

sed

cent

er

Exh

aust

cen

ter

Pre

ssur

e ce

nter

C4

(ø4)

C6

(ø6)

C8

(ø8)

• Low power consumption: 0.65W (with light) (Current value: 27mA, 24VDC)




34


Series SX3000/5000


How to Order Valves How to Order Manifold AssembliesExample

SS5X3-45GD-05U-C6 ....1 set (manifold part number)

∗ SX3140-5LOZ ... 3 sets (single solenoid part number)

∗ SX3240-5LOZ ... 2 sets (double solenoid part number)

Double solenoidSX3240-5LOZ (2 sets)

Single solenoidSX3140-5LOZ (3 sets)

Manifold

SS5X3-45GD-05U-6

Supply/Exhaust block (U side mounting)

2 1

Station

U side

D side

3 SX30005 SX5000

Series

1 2 position single2 position double3 position closed center3 position exhaust center3 position pressure center

2345 5 24VDC

NilR

Type of actuation Manual overrideNil Non-locking push type

Slotted locking typeD

5LOZSX 3 2 40

Rated voltage

Symbol Applicable stations

DU

B

2 to 10 stations2 to 10 stations2 to 16 stations

Mounting positionU sideD side

Both sidesM Special specifications

3 SX30005 SX5000

Series

∗ Indicate special specifications separately on a manifold specification sheet.

Symbol Mounting positionU U sideD D side

Connector mounting position

45GSS5X 3 05 U C4D

Symbol Port sizeø4 One-touch fittingø6 One-touch fittingø8 One-touch fitting

Mixed

C4C6C8M

SX5000

SymbolNilRS

RS

SpecificationsInternal pilot specificationExternal pilot specificationInternal pilot specification/Built-in silencerExternal pilot specification/Built-in silencer

Supply/Exhaust blockassembly specifications

SymbolC4C6M

Port sizeø4 One-touch fittingø6 One-touch fitting

Mixed

SX3000

∗ Indicate mixed specifications separately on a manifold specification sheet.

A, B port size

Options

Valve stations

Double wiring specification

Specified wiring (up to 16 solenoids

are possible)

NoteSymbol

02

0802

16

……

Stations

2 stations

8 stations

2 stations

16 stations

……

24VDC-COM

SMC

The "∗ " symbol indicates mounting. Put the "∗ " symbol at the beginning of the part numbers for solenoid valves, etc., which are to be mounted.


• Indicate the valves to be mounted below the manifold part number, in order starting from station 1 as shown in the drawing. When a layout becomes complicated, please indicate on a manifold specification sheet.

Pilot typeInternal pilotExternal pilot

Note 1) Double wiring specifications: Single, double, 3 position and 4 position solenoid valves can be used at all of the manifold stations.

Specified layout: Indicate the wiring specifications on a manifold specification sheet.(Please note that in locations where single solenoid wiring is indicated, it will be impossible to use double or 3 and 4 position valves.)

Note 2) The number of blanking plate assemblies is also included.


When a DIN rail is required that is longer than the standard types, specify the number of stations. (max. 20 stations)

Series SX3000/5000

35

ModelManifold typeP (SUP), R (EXH) systemValve stations Note1)


Port size

LocationDirection

P, Rports

A, Bports

SX3000SX5000SX3000

SX5000

SX3000SX5000

SX3000

SX5000

Valve effective areamm² (Cv factor)

Weight W (g) n: Stations

Flat cable type 45GPlug-in type

Common SUP, EXH

BaseSide

C8 (ø8 One-touch fitting)C10 (ø10 One-touch fitting)

C4 (ø4 One-touch fitting)/C6 (ø6 One-touch fitting) C4 (ø4 One-touch fitting)/C6 (ø6 One-touch fitting)

C8 (ø8 One-touch fitting) C6: P→A/B4.68 (0.26) A/B→R 4.68 (0.26) C8: P→A/B12.6 (0.7) A/B→R 12.6 (0.7)

2 to 16 stations

2 to 10 stations : W = 26n + 17211 to 16 stations: W = 26n + 199

2 to 10 stations : W = 54n + 22711 to 16 stations: W = 54n + 264

Manifold Specifications Solenoid Valve Specifications

Response Time

Weights

SeriesFluidInternal pilotoperatingpressure rangeMPa


Ambient and fluid temperature °CMax. operatingfrequency HzManual overridePilotexhaust

Mounting orientationImpact/Vibration resistance m/s² Note)

Enclosure

SX3000 SX5000Air

0.15 to 0.70.1 to 0.70.2 to 0.7

-100kPa to 0.7

0.25 to 0.7

Maximum 50103

53

Pilot valve individual exhaust typeMain valve, pilot valve common exhaust type

Lubrication Not requiredUnrestricted

150/30Dust proof

2 position single2 position double3 positionOperating pressure range


2 position double2 position single

3 position

2 position single, double3 position


Non-locking push type, Slotted locking type

Note) Impact resistance: No malfunction when tested with a drop tester in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states.

Vibration resistance: No malfunction when tested with one sweep of 8.3 to 2000Hz in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states. (Initial value)

Rated coil voltage Allowable voltage fluctuationPower consumption Surge voltage suppressorIndicator light

24VDC±10% of rated voltage

0.65WDiodeLED

Type of actuationWith light/surge voltage suppressor

Response time ms

15 or less

SX3000

SX5000

13 or less2 position double

20 or less3 position


Response time ms

26 or less22 or less38 or less

Type of actuation Weight g6775

78

7583

89

Valve modelSingleDouble


SingleDouble


2 position

3 position

2 position

3 position

SX340

SX540

Solenoid Specifications

2 position single

2 position double3 position

2 position single

Note 2)

Note 3)



Note 2) The value is for manifold base mounting (5 stations). 2 position type with single action.

Note 3) The weight W is the value for the manifold only. To obtain the weight with solenoid valves, add the solenoid valve weights for the required number of stations. Furthermore, when mounting supply/exhaust block assemblies on both sides of type B with a 2 to 10 station manifold, calculate the weight W using the formula for 11 to 16 stations.

36

5 Port Solenoid Valve Series SX3000/5000

SX3000: Flat Cable Type/Plug-inStationsSS5X3-45GU- D-C4

C6

StationsSS5X3-45GU- B-C4C6

StationsL1L2L3L4

2123112.591.515.5

135.512510216.5

148137.5112.517.5

148137.512312.5

160.5150133.513.5

173162.514414.5

185.5175154.515.5

198187.516516.5

210.5200175.517.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

2135.512510813.5

148137.5118.514.5

160.515012915.5

173162.5139.516.5

185.517515017.5

185.5175160.512.5

198187.517113.5

210.5200181.514.5

223212.519215.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

12248237.521317.5

11235.5225202.516.5

248237.5223.512

260.525023413

273262.5244.514

285.527525515

13 14 15 16

Note) L1 to L4 dimensions of SS5X3-45GU- Stations U- are the same as SS5X3-45GU- Stations D-.

37

Series SX3000/5000

StationsSS5X3-45GD- - C4C6

StationsSS5X3-45GD- B- C4C6

StationsL1L2L3L4

2 123112.591.515.5

135.512510216.5

148137.5112.517.5

148137.512312.5

160.5150133.513.5

173162.514414.5

185.5175154.515.5

198187.516516.5

210.5200175.517.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

2 135.512510813.5

148137.5118.514.5

160.515012915.5

173162.5139.516.5

185.517515017.5

185.5175160.512.5

198187.517113.5

210.5200181.514.5

223212.519215.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

12248237.521317.5

11235.5225202.516.5

248237.5223.512

260.525023413

273262.5244.514

285.527525515

13 14 15 16


38


SX5000: Flat Cable Type/Plug-in

StationsSS5X5-45GU- D-C4C6C8

StationsSS5X5-45GU- B-C4C6C8

StationsL1L2L3L4

2135.512510515

148137.512113.5

160.515013711.5

185.517515316

198187.516914.5

210.520018512.5

235.522520117

248237.521715.5

260.525023313.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

2148137.512312.5

173162.513917

185.517515515

198187.517113.5

210.520018711.5

235.522520316

248237.521914.5

260.525023512.5

285.527525117

3 4 5 6 7 8 9 10

StationsL1L2L3L4

12310.530028313.5

11 298287.526715.5

323312.529912

348337.531516.5

360.535033114.5

373362.534713

13 14 15 16


39

Series SX3000/5000

StationsSS5X5-45GD- U-C4C6C8

StationsSS5X5-45PD- B-C4C6C8

StationsL1L2L3L4

2135.512510515

148137.512113.5

160.515013711.5

185.517515316

198187.516914.5

210.520018512.5

235.522520117

248237.521715.5

260.525023313.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

2148137.512312.5

173162.513917

185.517515515

198187.517113.5

210.520018711.5

235.522520316

248237.521914.5

260.525023512.5

285.527525117

3 4 5 6 7 8 9 10

StationsL1L2L3L4

12310.530028313.5

11298287.526715.5

323312.529912

348337.531516.5

360.535033114.5

373362.534713

13 14 15 16

Note) L1 to L4 dimensions of SS5X5-45GU- Stations D- are the same as SS5X5-45G- Stations U-.

40


SX3000: Flat Cable 20 Pin TypePlug-in Type, DIN Rail Manifold





Indicate the layout of valves, etc., with "X's". (When A, B port sizes are mixed, indicate the sizes in section (a) with C4 and C6.)

For SMC use only



3 Station Table

SS5X3-45GOptionsWhen a DIN rail is required that is longer

than the standard types, specify the number

of stations. (max. 20 stations)

RS

RS

SpecificationsStandard/Internal pilot specificationExternal pilot specificationsInternal pilot/Built-in silencerExternal pilot/Built-in silencer

Supply/Exhaust block assembly specifications

Symbol

SymbolNil

C4C6M

Specificationsø4 One-touch fittingø6 One-touch fitting

Mixed

A, B port size

DBM

Mountingposition Applicable stations

2 to 10 stations

2 to 16 stations

U sideD side

Both sidesSpecial specifications

Symbol

U

Indicate special specifications in the station table below.

Symbol Mounting position

U U sideD D side

Connectormounting direction

Valve stations

…2 stationsDouble wiring specifications

Up to 16 solenoids are possible.Indicate wiring specifications in section (e) of the specification table.

Note

8 stations

…02StationsSymbol

08

…2 stations

16 stations

…02

16

Indicate mixed specifications in the station table below.

1 2 position single solenoid2 2 position double solenoid3 3 position closed center4 3 position exhaust center5 3 position pressure center

Make selections in the station table below.

Type of actuation

Nil

D Slotted locking type


Manual override

SX3 ∗ 40 ∗ 5LOZA

Valve stations or layout

2 position

1234567891011121314151617181920

3 position

Blanking plate assembly

SUP blocking diskEXH blocking disk

AccessoriesIndividual SUP spacer assemblyIndividual EXH spacer assemblySingle wiringDouble wiring

Single solenoidDouble solenoidClosed centerExhaust centerPressure center

Notes • Blanking plate assembly: SX3000-75-2A• SUP blocking disk: SX3000-77-1A• EXH blocking disk: SX3000-77-1A (2pcs./location)

• Individual SUP spacer assembly: SX3000-38-3A• Individual EXH spacer assembly: SX3000-39-3A• Supply/Exhaust block assembly (standard): SX3000-51-2A

• Supply/Exhaust block assembly (R): SX3000-51-6A• Supply/Exhaust block assembly (S): SX3000-51-7A• Supply/Exhaust block assembly (RS): SX3000-51-8A

a

b

c

d

Wiringspecificationse

Enter only when wiring specification instructions are necessary for 9 stations or more, and 8 stations or less.

ANilR


Pilot type

When using an external pilot valve, enter an "X" in the "external pilot specification" section of the stationtable below.

Company name

Contact person


Purchase order no.

Equipment name

Quantity set(s) Date required

Date / /


External pilot specification(enter only in case of external pilot)

Enter forspecial specs.

Supply/Exhaust block assembly

Order no.

Clerk (code no.)

Dept. code

Part no. QuantityPart no. Quantity


Note) When there are special specifications for the mounting position of supply/exhaust block assemblies, enter the part numbers and quantities for supply/exhaust block assemblies together with the manifold model.

Quantity

Also includes the number of blanking plate assemblies.


41

SX5000: Flat Cable 20 Pin TypePlug-in Type, DIN Rail Manifold






3 Station Table

SS5X5-45GOptionsWhen a DIN rail is required that is longer

than the standard type, specify the

number of stations. (max. 20 stations)

RS

RS

Symbol

SymbolNil

C4C6

M

Specificationsø4 One-touch fittingø6 One-touch fitting

C8 ø8 One-touch fittingMixed

A, B port size

DBM

U

UD


Valve stations

…2 stationsNote

8 stations

…02StationsSymbol

08

…2 stations

16 stations

…02

16

Indicate mixed specifications in the station table below.

12345

Make selections in the station table below.

Nil

D

SX5 ∗ 40 ∗ 5LOZA

1 Quantity234567891011121314151617181920

a

b

c

d

e

Enter only when wiring specification instructions are necessary for 9 stations or more, and 8 stations or less.

ANilR

Company name

Contact person


Purchase order no.

Equipment name


Date / /Please copy this page for use without removing it.

Symbol Mounting positionU sideD side

Double wiring specifications

Up to 16 solenoids are possible.Indicate wiring specifications in section (e) of the specification table.

Mountingposition Applicable stations

2 to 10 stations

2 to 16 stations

U sideD side


Symbol

Indicate special specifications in the station table below.


SpecificationsStandard/Internal pilot specificationExternal pilot specificationInternal pilot/Built-in silencerExternal pilot/Built-in silencer


2 position single solenoid2 position double solenoid3 position closed center3 position exhaust center3 position pressure center

Type of actuationInternal pilotExternal pilot

Pilot type

When using an external pilot valve, enter an "X" in the "external pilot specification" section of the station table below.



Manual override

Indicate the layout of valves, etc., with "X's". (When A, B port sizes are mixed, indicate the sizes in section (a) with C4, C6 and C8.)


2 position

3 position


SUP blocking diskEXH blocking disk

AccessoriesIndividual SUP spacer assemblyIndividual EXH spacer assemblySingle wiringDouble wiring

Single solenoidDouble solenoidClosed centerExhaust centerPressure center

Wiringspecifications

External pilot specification(enter only in case of external pilot)

Enter forspecial specs.

Supply/exhaust block assembly

Notes • Blanking plate assembly: SX5000-76-2A• SUP blocking disk: SX5000-77-1A• EXH blocking disk: SX5000-77-1A (2pcs./location)

• Individual SUP spacer assembly: SX5000-38-3A• Individual EXH spacer assembly: SX5000-39-3A• Supply/Exhaust block assembly (standard): SX5000-51-2A

• Supply/Exhaust block assembly (R): SX5000-51-6A• Supply/Exhaust block assembly (S): SX5000-51-7A• Supply/Exhaust block assembly (RS): SX5000-51-8A

Part no. Quantity

Enter the ordered part numbers.For SMC use only

Part no. Quantity Order no.

Clerk (code no.)

Dept. code

Note) When there are special specifications for the mounting position of supply/exhaust block assemblies, enter the part numbers and quantities for the supply/exhaust block assemblies together with the manifold model.

Also includes the number of blanking plate assemblies.


42

43

Series



SY340

SY540

Effective areamm²

(Cv factor)

4.68 (0.26)

12.6 (0.7)

—

Sin

gle

Dou

ble

Clo

sed

cent

er

Exh

aust

cen

ter

Pre

ssur

e ce

nter

C4

(ø4)

C6

(ø6)

C8

(ø8)

• Low power consumption: 0.55W (with light) (Current value: 23mA, 24VDC)




44


Series SY3000/5000


How to Order Valves How to Order Manifold AssembliesExample

SS5Y3-45GD-05U-C6 ..... 1 set (manifold part number)

∗ SY3140-5FU ....... 3 sets (single solenoid part number)

∗ SY3245-5FU ....... 1 set (double solenoid part number)


• Indicate the valves to be mounted below the manifold part number, in order starting from station 1 as shown in the drawing. When a layout becomes complicated, please indicate it on a manifold specification sheet.

• Since double and 3 position (dual body type) valves use two stations on a manifold base, be careful of the number of stations in manifold base part numbers.

Double solenoidSY3245-5FU (1 set)

Single solenoid

SY3140-5FU (3 sets)

ManifoldSS5Y3-45GD-05U-C6

Supply/Exhaust block (U side mounting)

12

3

Stations

D side

U side

5SY 3 1 FU

3 SY30005 SY5000

2 position single

5SY 3 2

4

4

0

5 FUDouble/3 position

2 2 position double3 3 position closed center4 3 position exhaust center5 3 position pressure center

5 24VDC

NilR

Nil Non-locking push typeDE

Series

Type of actuation

Dual body type (double/3 position)

Rated voltage

Pilot type

Manual override

Symbol Applicable stations

DU

B 2 to 16 stations2 to 10 stations2 to 10 stations

Mounting position

D sideU side

Both sidesM Special specifications

3 SY30005 SY5000

Series

∗ Indicate special specifications separately on a manifold specification sheet.

When a DIN rail is required that islonger than the standard type, specify the number of stations.(max. 20 stations)

Symbol Mounting positionU U sideD D side

Connector mounting position

Valve stations

45GSS5Y 3 05 U C4D

• Two stations are required for double and 3 position (dual body type).

• Also includes the number of blanking plate assemblies.

Symbol Port sizeø4 One-touch fittingC4ø6 One-touch fittingC6ø8 One-touch fittingC8

MixedM

SymbolNilRS

RS

Specifications

SY5000Symbol Port size

ø4 One-touch fittingC4ø6 One-touch fittingC6

MixedM

SY3000

Supply/Exhaust block assemblymounting direction

A, B port size

Supply/Exhaust blockassembly specifications

Options

NoteSingle wiring

specifications (up to 16 solenoids

are possible)

StationsSymbol

…

16

…

02 2 stations

16 stations

24VDC+COM

+-

SMC

∗ Indicate mixed specifications separately on a manifold specification sheet.

Internal pilot specificationExternal pilot specificationInternal pilot specification/Built-in silencerExternal pilot specification/Built-in silencer

Slotted locking typeKnob locking type


The "∗ " symbol indicates mounting. Put the "∗ " symbol at the beginning of the part numbers for solenoid valves, etc., which are to be mounted.

Series SY3000/5000

45

Manifold Specifications Solenoid Valve Specifications

Solenoid Specifications

Response Time

Rated coil voltageAllowable voltage fluctuationPower consumptionSurge voltage suppressorIndicator light

24VDC±10% of rated voltage

0.55WDiodeLED

ModelManifold typeP (SUP), R (EXH) systemValve stations Note1)

Port size


SY3000SY5000SY3000

SY5000

SY3000SY5000

SY3000

SY5000

Weight W (g) n: Stations(D-sub connector)

Flat cable type 45GPlug-in type

Common SUP/EXH

BaseSide

C8 (ø8 One-touch fitting) C10 (ø10 One-touch fitting)

C4 (ø4 One-touch fitting)/C6 (ø6 One-touch fitting) C4 (ø4 One-touch fitting)

C6 (ø6 One-touch fitting)/C8 (ø8 One-touch fitting) C6: P→A/B 4.68 (0.26) A/B→R 4.68 (0.26)C8: P→A/B 12.6 (0.7) A/B→R 12.6 (0.7)

2 to 16 stations

2 to 10 stations: W = 26n + 17211 to 16 stations: W = 26n + 199

2 to 10 stations: W = 54n + 22711 to 16 stations: W = 54n + 264

Manual override

Pilotexhaust type

Mounting orientationImpact/Vibration resistance m/s² Note)

Enclosure

SY3000 SY5000Air

0.1 to 0.70.2 to 0.7

–100kPa to 0.7

0.25 to 0.7

Maximum 50103

53

Pilot valve individual exhaust type

Main valve/pilot valve common exhaust type

Lubrication Not requiredUnrestricted

150/30Dust proof

2 position single2 position double3 positionOperating pressure range

2 position single, double3 position


Non-locking push typeSlotted locking type, Knob locking type

0.15 to 0.7

Weights


Response time ms

12 or less2 position single10 or less2 position double16 or less3 position

19 or less18 or less32 or less

Type of actuation Weight g5177

82

59102

112.6

Valve modelSingleDouble


SingleDouble


2 position

3 position

2 position

3 position

SY345

SY3140

SY545

SY5140

SY3000

SY5000

LocationDirection

P/R ports

A/B ports

Valve effectivearea mm²(Cv factor)

SeriesFluidInternal pilotoperatingpressure rangeMPa


Ambient and fluid temperature °C

2 position single2 position double3 position


Max. operatingfrequency Hz

Note) Impact resistance: No malfunction when tested with a drop tester in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states. (Initial value)

Vibration resistance:No malfunction when tested with one sweep of 8.3 to 2000Hz in the axial direction and at a right angle to the main valve and armature, in both energized and deenergized states. (Initial value)

Response time ms

With light/surge voltage suppressorType of actuation

2 position single2 position double3 position

Note 2)

Note 3)



Note 2) The value is for manifold base mounting (5 stations). 2 position type with single action.

Note 3) The weight W is the value for the manifold only. To obtain the weight with solenoid valves, add the solenoid valve weights for the required number of stations. Furthermore, when mounting supply/exhaust block assemblies on both sides of type B with a 2 to 10 station manifold, calculate the weight W using the formula for 11 to 16 stations.

46

5 Port Solenoid Valve Series SY3000/5000

SY3000: Flat Cable Type/Plug-inStationsSS5Y3-45GU- D- C4

C6

StationsSS5Y3-45GU- B-C4C6

C4C6

Stations

L1L2L3L4

2123112.591.515.5

135.512510216.5

148137.5112.517.5

148137.512312.5

160.5150133.513.5

173162.514414.5

185.5175154.515.5

198187.516516.5

210.5200175.517.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

2135.512510813.5

148137.5118.514.5

160.515012915.5

173162.5139.516.5

185.517515017.5

185.5175160.512.5

198187.517113.5

210.5200181.514.5

223212.519215.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

12248237.521317.5

11 235.5225202.516.5

248237.5223.512

260.525023413

273262.5244.514

285.527525515

13 14 15 16

Note) L1 to L4 dimensions of SS5Y3-45GU- Stations U- are the same as SS5Y3– 45GU- Stations D- .

C4C6

47

Series SY3000/5000

StationsSS5Y3-45GD- U-C4C6

StationsSS5Y3-45GD- B-C4C6

StationsL1L2L3L4

2123112.591.515.5

135.512510216.5

148137.5112.517.5

148137.512312.5

160.5150133.513.5

173162.514414.5

185.5175154.515.5

198187.516516.5

210.5200175.517.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

2135.512510813.5

148137.5118.514.5

160.515012915.5

173162.5139.516.5

185.517515017.5

185.5175160.512.5

198187.517113.5

210.5200181.514.5

223212.519215.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

12248237.521317.5

11235.5225202.516.5

248237.5223.512

260.525023413

273262.5244.514

285.527525515

13 14 15 16

C4C6

C4C6

Note) L1 to L4 dimensions of SS5Y3–45GD- Stations D-are the same as SS5Y3–45GD- Stations U- .

48


SY5000: Flat Cable Type/Plug-inStationsSS5Y5-45GU- D-C4

C6C8

Stations SS5Y5-45GU- B- C4C6C8

StationsL1L2L3L4

2135.512510515

148137.512113.5

160.515013711.5

185.517515316

198187.516914.5

210.520018512.5

235.522520117

248237.521715.5

260.525023313.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

2148137.512312.5

173162.513917

185.517515515

198187.517113.5

210.520018711.5

235.522520316

248237.521914.5

260.525023512.5

285.527525117

3 4 5 6 7 8 9 10

StationsL1L2L3L4

12310.530028313.5

11298287.526715.5

323312.529912

348337.531516.5

360.535033114.5

373362.534713

13 14 15 16

C4C6C8 C4

C6C8

Note) L1 to L4 dimensions of SS5Y5-45GU- Stations U- are the same as SS5Y5-45GU- Stations D- .

49

Series SY3000/5000

StationsSS5Y5-45GD- U-C4C6C8

StationsSS5Y5-45GD- B-C4C6C8

StationsL1L2L3L4

2135.512510515

148137.512113.5

160.515013711.5

185.517515316

198187.516914.5

210.520018512.5

235.522520117

248237.521715.5

260.525023313.5

3 4 5 6 7 8 9 10

StationsL1L2L3L4

2148137.512312.5

173162.513917

185.517515515

198187.517113.5

210.520018711.5

235.522520316

248237.521914.5

260.525023512.5

285.527525117

3 4 5 6 7 8 9 10

StationsL1L2L3L4

12310.530028313.5

11298287.526715.5

323312.529912

348337.531516.5

360.535033114.5

373362.534713

13 14 15 16

C4C6C8

C4C6C8

Note) L1 to L4 dimensions of SS5Y5-45GD- Stations D-

are the same as SS5Y5-45GD- Stations U- .

50


SY3000: Flat Cable 20 Pin TypePlug-in Type, DIN Rail Manifold





• In the case of a single solenoid, enter an "X" in one station box.• For double and 3 position, enter an "X" across two station boxes. (Refer to the entry example below.) [When A, B port sizes are mixed, indicate the sizes in section (a) with C4 and C6.]

Note) Connector blocks are not included in stations and layouts.



3 Station Table

SS5Y3-45G

…

2 stations Single wiringspecifications

(up to 16 solenoidsare possible.)

Note

16 stations

…

02StationsSymbol

16

RS

RS

Nil

C4C6M

ø4 One-touch fittingø6 One-touch fitting

Mixed

DBM

2 to 10 stations

2 to 16 stations

U sideD side


U


• Since valves other than single solenoids are dual body types, they require two stations.

U U sideD D side


Valve stations

Indicate mixed mounting in the station table below by entering C4 and C6 instead of "X's".

A

140 Standard

Dualbodytype

245345445545Indicate in the station table below.

Type of valve actuationBody option

SY3 ∗∗∗ ∗ 5FU

Nil

D

E



Knob locking type

NilR

Pilot type


2 position

1 Quantity234567891011121314151617181920

3 position

3 port valve




SUP blocking disk

Single solenoidDouble solenoid


2 positionSingle solenoidDouble solenoid

Closed centerExhaust centerPressure centerN.C. singleN.C. doubleN.O. singleN.O. double

a

a

b

c

[Entry example]

Ref

er to

the

entr

yex

ampl

e.

6

C 6

5 4C4

3 2 1

XX

Notes• Blanking plate assembly: SX3000-75-2A• SUP blocking disk: SX3000-77-1A• EXH blocking disk: SX3000-77-1A (2pcs./location)

• Supply/Exhaust block assembly (standard): SX3000-51-2A• Supply/Exhaust block assembly (R): SX3000-51-6A• Supply/Exhaust block assembly (S): SX3000-51-7A• Supply/Exhaust block assembly (RS): SX3000-51-8A

When the port sizes are mixed

External pilot specification(enter only for external pilot)

EXH blocking disk (2pcs./location)

A Manual override

Company name

Contact person


Purchase order no.

Equipment name


Date / /

OptionsWhen a DIN rail is required that is longer than the standard type, specify the number of stations. (max. 20 stations)

Symbol SpecificationsA, B port size

Symbol Specifications


Standard/Internal pilot specificationExternal pilot specification

Internal pilot/Built-in silencerExternal pilot/Built-in silencer

Mountingposition Applicable stationsSymbol



2 position single2 position double3 position closed center3 position exhaust center3 position pressure center



Order no.

Clerk (code no.)

Dept. code

Note) When there are special specifications for the mounting position of supply/exhaust block assemblies, enter the part numbers and quantities for the supply/exhaust block assemblies together with the manifold model.

For SMC use only



Indicate special specifications, in the station table below.


51


• In the case of a single solenoid, enter an "X" in one station box.• For double and 3 position, enter an "X" across two station boxes. (Refer to the entry example below.) [When A, B port sizes are mixed, indicate the sizes in section (a) with C4 and C6.]



3 Station Table

SS5Y5-45G

…2 stations

16 stations

…02

16

RS

RS

SymbolNil

C4C6

M

ø6 One-touch fittingC8 ø8 One-touch fitting

Mixed

A, B port size

DBM


Symbol

U


• Since valves other than single solenoids are dual body types, they require two stations.

UD

Valve stations

A

140245345445545Indicate in the station table below.

SY5 ∗∗∗ ∗ 5FU

D

E

NilR

1 Quantity234567891011121314151617181920

a

a

b

c

6

C 6

5 4C4

3 2 1

XX

When the port sizes are mixed

Note) Connector blocks are not included in stations and layouts.

Company name

Contact person


Purchase order no.

Equipment name


Date / /

SY5000: Flat Cable 20 Pin TypePlug-in Type, DIN Rail Manifold





U sideD side



OptionsWhen a DIN rail is required that is longer than the standard type, specify the number of stations. (max. 20 stations)

ø4 One-touch fittingSymbol Specifications

Indicate mixed mounting in the station table below by entering C4, C6 and C8 instead of "X's".

Specifications


Standard/Internal pilot specificationExternal pilot specification

Internal pilot/Built-in silencerExternal pilot/Built-in silencer

NoteStationsSymbolSingle wiring specifications

(up to 16 solenoidsare possible.)

Mountingposition Applicable station

2 to 10 stations

2 to 16 stations

U sideD side


In case of special specifications, indicate in the station table below.

Standard

Dualbodytype

Valve actuation/Body option2 position single2 position double3 position closed center3 position exhaust center3 position pressure center

Pilot typeInternal pilotExternal pilot


Nil Non-locking push type


Knob locking type

A Manual override


2 position

3 position

3 portvalve


Single solenoidDouble solenoidClosed centerExhaust centerPressure centerN.C. singleN.C. doubleN.O. singleN.O. double

Ref

er to

the

entr

yex

ampl

e.

External pilot specification(enter only for external pilot)



SUP blocking disk


2 position Single solenoidDouble solenoid

[Entry example]

EXH blocking disk (2pcs./location)

Notes• Blanking plate assembly: SX5000-76-2A • SUP blocking disk: SX5000-77-1A• EXH blocking disk: SX5000-77-1A

(2pcs./location)

• Supply/Exhaust block assembly (standard): SX5000-51-2A• Supply/Exhaust block assembly (R): SX5000-51-6A• Supply/Exhaust block assembly (S): SX5000-51-7A• Supply/Exhaust block assembly (RS): SX5000-51-8A

Order no.

Clerk (code no.)

Dept. codeNote) When there are special specifications for the

mounting position of supply/exhaust block assemblies, enter the part numbers and quantities for supply/exhaust block assemblies together with the manifold model.

For SMC use only



52

53

Series

VQ130Metal sealVQ131Rubber seal

Effective areamm²

(Cv factor)

4.5 (0.25)

6.3 (0.35)

C4

(ø4)

C3

(ø3.2)

C6

(ø6) M5

Sin

gle

Dou

ble

Clo

sed

cent

er

Exh

aust

cen

ter

Pre

ssur

e ce

nter

Type of actuation Cylinder port size


• Compact manifold for efficient use of space

• Valves can be replaced without disassembling the entire manifold

• Seal type allows selection of metal seals or rubber seals

54

5 Port Solenoid ValveBody Ported Type/Flip Plug-in Unit

Series VQ1000


How to Order Valves

VQ1 3 5

Symbol12

3 Note)

4 Note)

5 Note)

Type of actuation2 position double2 position double (latching) 3 position closed center3 position exhaust center3 position pressure center

SymbolNil

H Note 2)

Y Note 2)

SpecificationsStandard type (1W)

High pressure type (1.5W) Low power consumption type

(0.5W)

SymbolC3C4C6M5

Port sizeOne-touch fitting for ø3.2One-touch fitting for ø4One-touch fitting for ø6

M5 threads

SeriesVQ1000

Type ofactuation

Options(with blocking valve & port plug)

Function

Rated voltage

Symbol01

Seal typeMetal sealRubber seal

Seal type

Cylinder port size

Series VQ1000

Symbol Stations01 1 station

16 16 stations

Stations

Electrical entry/Cable length

VV5Q13 (-00T) J

SymbolNilD

DKNS

SpecificationsNoneWith DIN rail (Rail length: Standard) With DIN rail (Rail length: Special) Note 2)

Special wiring specifications (except double wiring) Note 3)

With name plateBuilt-in silencer & direct exhaust

Note 1) Numbers inside ( ) indicate the maximum number of solenoids for mixed single/double wiring. The maximum number of stations is determined by the total number of solenoids. In case of mixed wiring, add the option symbol "-K".

Note 1) When specifying two or more options, enter symbols in alphabetical order.

Note 2) Except double (latching) type

Note) The 3 position type uses two stations.

SymbolNilPR

PR

AB

SpecificationsNone

With SUP blocking plateWith EXH blocking plate

With SUP/EXHblocking plate

Port plug (A port)Port plug (B port)

Note) Since blocking plates are built into valves, add the above option symbols when required.

Note) Inch sizes use the following symbols. • N1: ø1/8˝ • N3: ø5/32˝ • N7: ø1/4˝

Symbol

Nil

BC

Manual override

Non-locking push type (tool required)

Slotted locking type (tool required)Knob locking type (manual type)

Manual override

Options

P, R port inch bore size

… …

Top entry

U0

Side entry

S0

KitFlat cable kit

(20P) without cable

Stations Note 1)

1 to 8 (16)

How to Order Manifold Assemblies

<Example>

VV5Q13-08JUO … 1 set — Manifold base part number∗ VQ1130-5-C6 … 4 sets — Valve part number (Stations 1 to 4)∗ VQ1230-5B-C6 … 4 sets — Valve part number (Stations 5 to 8)

Flat cable kit

5 24VDC

Note 1) In case of two or more options, enter them in alphabetical order.Example: –DS

Note 2) Indicate special DIN rail length as "D" ( indicates stations) Example: –D08In this case, an eight station DIN rail will be provided regardless of the number of manifold stations.Indicate "-D0" for no DIN rail.

Note 3) Be sure to indicate wiring specifications on a manifold specification sheet.

Enter part numbers for valves and options to be mounted below the manifold base part number.

Enter in order starting from the first station on the D side. When entry of part numbers becomes complicated, indicate them on a manifold specification sheet.

Add the "∗ " symbol at the beginning of part numbers for solenoid valves, etc., to be mounted.

Stations

D sideU side

12

3

Series VQ1000

55

Series ModelResponse time msSta dard:1WLow power

Effective areamm2 (Cv factor)

Number of solenoidsNote 1) Note 2)

Models



Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

VQ1130

VQ1131

VQ1230

VQ1231

VQ1330

VQ1331

VQ1430

VQ1431

VQ1530

VQ1531

4.5 (0.25)

6.3 (0.35)

4.5 (0.25)

6.3 (0.35)

4.5 (0.25)

6.3 (0.35)

4.5 (0.25)

6.3 (0.35)

4.5 (0.25)

6.3 (0.35)

12 or less

15 or less

12 or less

15 or less

20 or less

25 or less

20 or less

25 or less

20 or less

25 or less

15 or less

20 or less

15 or less

20 or less

26 or less

33 or less

26 or less

33 or less

26 or less

33 or less

Double(latching)

Single

Val

ve s

pec

ifica

tion

sE

lect

rica

l sp

ecifi

catio

ns

VQ

1000 Closed

center

Exhaustcenter

Pressurecenter

110

57

3 p

osit

ion

2 p

osit

ion

Valve construction

Fluid

Max. operating pressure



Lubrication

Manual override


Enclosure

Rated coil voltage



Metal seal

Air, Inert gas

0.1MPa

0.18MPa

0.1MPa

Rubber seal

Air, Inert gas

0.15MPa

0.18MPa

0.2MPa

Single

Double (latching)

3 position

24VDCPower consumption(current value)

Note 2)


–10 to 50°C Note 1)

Not required

Push type/Locking type(slotted type, knob type) optional

150/30m/s²

Dust proof

24VDC


Class B equivalent

DC1W (42mA), DC1.5W (63mA),Note 3) 0.5W (21mA) Note 4)

Series

VQ1000 VV5Q13-

Basemodel Port

location

Side1 to 16stations

P, R A, B

Piping specificationsApplicable

stations

5 st

atio

nw

eigh

t g

Applicablesolenoidvalves

Port size

C6 (for ø6) C3 (for ø3.2) C4 (for ø4) C6 (for ø6) M5 (M5 thread)

Options:Built-in silencerDirect exhaust

VQ1 30

VQ1 31424

Series Model

Response time ms

Standard: 1WH: 15W

Low powerand AC

Effective area mm²(Cv factor) W

eigh

t g

Number ofsolenoids

Note 1) Note 2)

Note 1) Values are for cylinder port size C6.Note 2) Based on JISB8375-1981 (Values for supply pressure of 0.5MPa with

light/surge voltage suppressor using clean air. This will change depending on pressure and air quality.)

Note 1) In case of low temperature, use dry air with no condensation.Note 2) Impact resistance ….... No malfunction when tested with a drop and

impact tester in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states. (Initial value)

Vibration resistance … No malfunction when tested with one sweep of 8.3 to 2000Hz in the axial direction and at a right angle to the main valve and armature, in both energized and deenergized states. (Initial value)

Note 3) Value for high pressure type (1.5W) specificationNote 4) Value for the low power consumption (0.5W) specification

56

5 Port Solenoid Valve Series VQ1000

VQ1000/Flat Cable Kit

DimensionsL n

L1L2

(L3 ) (L4 )

26.566

87.598

37.577100

110.5

48.588

112.5123

59.599125

135.5

70.5110

137.5148

81.5121150

160.5

92.5132

162.5173

103.5143

162.5173

114.5154175

185.5

125.5165

187.5198

136.5176200

210.5

147.5187

212.5223

158.5198225

235.5

169.5209

237.5248

180.5220250

260.5

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15191.5231

262.5273

16

7

19.2P = 11

(7.

5)

(11

)13

.5 24.5

9

61.5 (5.

5)

R4.

5

(35

)

26

62.5

97 =

4.5

(11)

41

35

(L4)

(L3) (5.2)

L223.5

1.5

P = 11 13.2L1 6.2

1.5

52

Applicable connector: Flat cable connector (20P)


2n-C3, C4, C6, M5

C3: One-touch fitting for ø3.2

C4: One-touch fitting for ø4


M5: M5 threads

StationsD side U side1 2 3 4 5 6 7 8 n

2-C6R(EXH) port

2-C6P(SUP) port

Indicator light

Manual override

2-M4 mounting hole

AP

R

P

R B

A

B

A

B

A

B

A

B

A

B

A

B

A

B

A A A A

A B1 0

A B1 0

A B1 0

A B1 0

StationsVV5Q13- J 0- (D)US

Formulae L1 = 11n + 15.5 L2 = 11n + 55 n: Stations (max. 16 stations)

19.5 (Mounting hole dimension)

Broken lines indicate DIN rail mount type [-D] and connector top entry [-JU].

Note) The 3 position type uses two stations.Cylinder ports are located on the U side of the body between two stations.

Series VQ1000

57

58

C C4

E FD


VV5Q J1 3 08 U0 N ( 00T )

For P, R port inch sizesKit designation

Flip, Plug-inSeries VQ1000

01

…

16

…

OptionsNil None

With DIN rail (Rail length: Standard) With DIN rail (Rail length: Special) Note 2)

Special wiring specifications (except double wiring) Note 3)

With name plateBuilt-in silencer, Direct exhaust

DDKNS

Top entry Side entryNote 1)

U0 S0 Flat cable kit (20P) Without cable 1 to 8 (16)

1

1

2

2

3

3


VQ 1 3 50 Y2

Series VQ1000

F

C

C

B

B

A

A

12

3 Note)

4 Note)

5 Note)

2 position single2 position double (latching)3 position closed center3 position exhaust center3 position pressure center

Manual operation Options (blocking valve & port plug)Nil Non-locking push type (tool required)

Slotted locking type (tool required) Knob locking type (manual type)

BC

Nil NoneWith SUP blocking plateWith EXH blocking plateWith SUP and EXH blocking platesPort plug APort plug B

PR

PRABCylinder port size

With One-touch fitting for ø3.2 With One-touch fitting for ø4With One-touch fitting for ø6M5 threads

C3C4C6M5Function

Type of actuation

01

D

ENote) The 3 position type uses two stations.

Specifications

Standard type

High pressure type

Low power consumption type

DC

(1.0W)

(0.5W)

Symbol

Nil

H Note 1)

Y Note 1)


Series VQ1000/Flip, Plug-in Unit

Note) Stations are counted starting from station 1 on the D side.

U side

D side

n

Stations

8

7

6

5

4

3

2

1

Stations1 station

16 stations


StationsKit, Cable length


Seal type


Note 1) When specifying more than one option, enter symbols in alphabetical order. Example) -DS

Note 2) Indicate special DIN rail length as “D” ( indicates stations).Example: -D08In this case, an eight station DIN rail will be provided regardless of the number of manifold stations.Indicate "-D0" for no DIN rail.


(1.5W)

Note 1) Except double (latching) type

Note 2) When specifying more than one option, enter symbols in alphabetical order.

Note) Inch sizes use the following symbols.• N1: ø1/8˝• N3: ø5/32˝• N7: ø1/4˝

Note) Since blocking plates are built into valves, add the above option symbols when required.

59


Series VQ1000/Flip, Plug-in Unit


VV5Q J1 3 ( 00T)

For P, R port inch sizes

Kit designationFlip, Plug-in

SeriesVQ1000

Note 2)

Note 2)

Note 4)

Single

Double(latching)

Closed center(uses two stations)

Pressure center(uses two stations)

Exhaust center(uses two stations)

Blanking plateVVQ1000-10A-3Individual SUP spacer Note 1) VVQ1000-P-3-C6

Individual EXH spacer Note 1) VVQ1000-R-3-C6

SUP shut-off position: Indicate one location.

EXH shut-off position: Indicate one location.

SUP shut-off position(for blocking valve) EXH shut-off position(for blocking valve)

Port plug Note 3)

With One-touch fittingfor ø3.2 (ø1/8˝) With One-touch fittingfor ø4 (ø5/32˝) With One-touch fittingfor ø6 (ø1/4˝)

M5 threads

Sideported

Sideported

Sideported

Sideported

C3(N1) C4

(N3) C6

(N7)

M5


Val

ves

Op

tion

s

← U side →


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Company name

Contact person


Purchase order no.

Equipment name


Date / /

Specifications D side∗ Enter an "X" in the required locations.


Single wiring

Double wiring


Part no. Part no. Qty.



Order no.

Clerk (code no.)

Dept. code

Cyl

ind

er p

ort

siz

eE

nter

in c

ase

of m

ixed

siz

es (

CM

).

Qty.

Metal seal Rubber seal

Not

es

Note 1) For individual SUP and EXH spacers, the D side of the SUP and EXH passages are shut off. Indicate one more shut-off position.Note 2) Blocking plates are built into valves. Indicate shut-off positions in the table above. (The D sides of the SUP and EXH passages are shut off.) Note 3) When using port plugs, circle the specified ports.Note 4) In case of single wiring or mixed wiring, connections to the connector terminals start from the A side solenoid of station 1 and continue in order without

skipping any terminals.

60

61

Series

Type of actuation Cylinder port size

2 position 3 position

3 position2 position

One-touch fitting

VQ100Metal sealVQ101Rubber sealVQ200Metal sealVQ201Rubber seal

Effective area mm² (Cv factor)

3.6 (0.2)

5.4 (0.3)

14.4 (0.8)

16.2 (0.9)

3.6 (0.2)

5.4 (0.3)

12.6 (0.7)

14.4 (0.8)

—

—

Sin

gle

Dou

ble

Clo

sed

cent

er

Exh

aust

cen

ter

Pre

ssur

e ce

nter

C4

(ø4)

—

—

C3

(3.2)

C6

(ø6)

C8

(ø8)

—

—

M5

• Space saving design locates all pilot valves on one side• One-clamp construction with no screws allows easy valve

replacement• A variety of options

Back pressure check valve, Built-in silencer, Name plate, etc.• Seal type allows selection of metal seals or rubber seals

62

5 Port Solenoid ValveBase Mounted Type/Plug-in Unit

Series VQ1000/2000


How to Order Valves

VQ 0 0 5

Symbol12345

Type of actuation2 position double2 position double3 position closed center3 position exhaust center3 position pressure center

SymbolNilHRY

FunctionStandard type (1W)

High pressure type (1.5W)External pilot

Low power consumption type (0.5W)

Type of actuation

Function

Symbol01


Seal type

SeriesSymbol Stations

12

VQ1000VQ2000

Cylinder port size

VV5Q 1 08 C6 GU0Symbol

Nil

B

D

D

G1G2G3J

K

NRS

VQ1000 specificationsNone

Back pressure check valveon all stations Note 2)

With DIN rail (Rail length: Standard)

With DIN rail(Rail length: Special) Note 3)

Regulator unit with 1 unit Note 4) Regulator unit with 2 units Note 4)

Regulator unit with 3 units Note 4)

With ejector unit Note 5)

Special wiring specifications(except double wiring) Note 6)

With name plateExternal pilot Note 7)

Built-in silencer, Direct exhaust

Note 1) When specifying two or more, list them in alphabetical order.

Symbol

Nil

BC

Manual overrideNon-locking push type

(tool required)

Slotted locking typeKnob locking type

Manual override

Options

VQ1000 VQ2000Symbol

C3C4C6M5CM

L3

L4

L6

L5

B3

B4

B6

B5

LM

Port sizeWith One-touch fitting for ø3.2With One-touch fitting for ø4With One-touch fitting for ø6M5 threadsMixed and with port plugElbow top portedWith One-touch fitting for ø3.2Elbow top portedWith One-touch fitting for ø4Elbow top portedWith One-touch fitting for ø6Elbow top portedM5 threadsElbow bottom portedWith One-touch fitting for ø3.2Elbow bottom portedWith One-touch fitting for ø4Elbow bottom portedWith One-touch fitting for ø6Elbow bottom portedM5 threadsElbow mixed port sizes

Electrical entry


Top entry

JU0

G0 (VQ1000)GU0 (VQ2000)

Side entry

JS0

——

J kit

G kit

KitFlat cable kit

(20P) without cableFlat cable kit (20P) with

terminal block without cable

Stations Note1)

2 to 8 (16)

2 to 8 (16)

2Symbol Stations

02 2 stations

16 16 stations

Stations

… …

2 1 Y

SeriesSymbol Stations

12

VQ1000VQ2000

SymbolC4C6C8CM

L4

L6

L8

B4

B6

B8

LM

Port sizeWith One-touch fitting for ø4With One-touch fitting for ø6With One-touch fitting for ø8Mixed and with port plugElbow top portedWith One-touch fitting for ø4Elbow top portedWith One-touch fitting for ø6Elbow top portedWith One-touch fitting for ø8Elbow bottom portedWith One-touch fitting for ø4Elbow bottom portedWith One-touch fitting for ø6Elbow bottom portedWith One-touch fitting for ø8Elbow mixed port sizes

Note 1) For CM and LM, indicate in the specification table.Note 2) Inch sizes use the following symbols.

VQ1000• N1: ø1/8"• N3: ø5/32"• N7: ø1/4"• N5T: 10-32UNF

• NM: MixedTop ported elbows are LN and bottom ported elbows are BN.

VQ2000 • N3: ø5/32" • N7: ø1/4" • N9: ø5/16" • NM: Mixed

SymbolNil

B

D

D

K

NRS

VQ2000 specificationsNone

Back pressure check valveon all stations Note 2)

With DIN rail (Rail length: Standard)

With DIN rail(Rail length: Special) Note 3)

Special wiring specifications(except double wiring) Note 6)

With name plateExternal pilot Note 7)


Flat cable kit with terminal blockVV5Q11-08C6G0 ... 1 set — Manifold base part number ∗ VQ1100-5 ... 4 sets — Valve part number (stations 1 to 4) ∗ VQ1200-5 ... 1 set — Valve part number (station 5) ∗ VQ1300-5 ... 3 sets — Valve part number (stations 6 to 8)

How to Order Manifold Assemblies

<Example>

Note 1) In case of two or more options, enter them in alphabetical order.Example) -BRS

Note 2) When using back pressure check valves only on required stations, enter the back pressure check valve part numbers and indicate the stations for mounting in the specification table.

Note 3) Indicate a special DIN rail length as “D” ( indicates stations).Example) -D08In this case, an eight station DIN rail will be provided regardless of the number of manifold stations. Indicate "-D0" for no DIN rail.

Note 4) Indicate regulator unit mounting stations in the specification table.Count as unit 1, station 1.

Note 5) Refer to the separate catalog CAT.E138-A for details when equipped with ejector unit. Also, "-J" and name plate "-N" cannot be combined.

Note 6) Be sure to indicate wiring specifications in the manifold specification table.

Note 7) In case of an external pilot "R", indicate external pilot specifications "R" for the applicable valve also.

Enter part numbers for valves and options to be mounted below the manifold base part number.

Enter in order starting from the first station on the D side. When entry of part numbers becomes complicated, indicate them on a manifold specification sheet.

Add the "∗ " symbol at the beginning of part numbers for solenoid valves, etc., to be mounted.

1

StationsU side

D side23

Series VQ1000/2000

63



VQ1100

VQ1101

VQ1200

VQ1201

VQ1300

VQ1301

VQ1400

VQ1401

VQ1500

VQ1501

3.6 (0.2)

5.4 (0.3)

3.6 (0.2)

5.4 (0.3)

3.6 (0.2)

5.4 (0.3)

3.6 (0.2)

5.4 (0.3)

3.6 (0.2)

5.4 (0.3)

12 or less

15 or less

10 or less

15 or less

20 or less

25 or less

20 or less

25 or less

20 or less

25 or less

15 or less

20 or less

13 or less

20 or less

26 or less

33 or less

26 or less

33 or less

26 or less

33 or less

VQ

1000

78

64

2 p

osi

tion

3 p

osi

tion

VQ2100

VQ2101

VQ2200

VQ2201

VQ2300

VQ2301

VQ2400

VQ2401

VQ2500

VQ2501

14.4 (0.8)

16.2 (0.9)

14.4 (0.8)

16.2 (0.9)

12.6 (0.7)

14.4 (0.8)

12.6 (0.7)

14.4 (0.8)

12.6 (0.7)

14.4 (0.8)

22 or less

24 or less

15 or less

20 or less

29 or less

34 or less

29 or less

34 or less

29 or less

34 or less

29 or less

31 or less

20 or less

26 or less

38 or less

44 or less

38 or less

44 or less

38 or less

44 or less

VQ

2000

110

90

2 p

osi

tion

3 p

osi

tion

Metal seal

Air, Inert gas

0.1MPa

0.1MPa

0.1MPa

Rubber seal

Air, Inert gas

0.15MPa

0.1MPa

0.2MPa

24VDC

Note 2)


–10 to 50°C Note 1)

Not required

Push type/Locking type(slotted type, knob type) optional

150/30m/s²

Dust proof

24VDC


Class B equivalent

DC1W (42mA), DC1.5W (63mA), Note 3)

DC0.5W (21mA) Note 4)

VQ

1000

VV5Q11- Side

P, R A, B

2 to 16stations

2 to 16stations

C8 (for ø8) C3 (for ø3.2) C4 (for ø4) C6 (for ø6) M5 (M5 threads)

VQ100

VQ101

628(single)759

(double, 3P)

VQ

2000

VV5Q21- Side

C10 (for ø10) C4 (for ø4) C6 (for ø6) C8 (for ø8)

VQ200

VQ201

1051(single)1144

(double, 3P)

Ser

ies

Basemodel

Piping specificationsApplicable

stations

5 stationweight

g

Applicablesolenoidvalves

Port size Note 1)



Models

Series Model

Response time ms

Standard: 1WH: 15W

Lowpower

Effective area mm²

(Cv factor)

Wei

ght

g

Number of solenoids

Note 2)

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Metal seal

Rubber seal

Double

Single

Closedcenter

Exhaustcenter

Pressurecenter

Double

Single

Closedcenter

Exhaustcenter

Pressurecenter

Val

ve s

pec

ifica

tion

sE

lect

rica

lsp

ecifi

catio

ns

Valve construction

Fluid

Max. operating pressure



Lubrication

Manual override


Enclosure

Rated coil voltage



Power consumption(current value)

Single

Double

3 position

Pipingdirection

Note 1) Values are for cylinder port sizes C6 (VQ1000) and C8 (VQ2000) without back pressure check valve.

Note 2) Based on JISB8375-1981 (Values for supply pressure of 0.5MPa with light/surge voltage suppressor, using clean air. This will change depending on pressure and air quality.) Value for the double type when ON.

Note 1) In case of low temperature, use dry air with no condensation.Note 2) Impact resistance ….... No malfunction when tested with a drop and impact

tester in the axial direction and at a right angle to the main valve and armature, one time in both energized and deenergized states. (Initial value)

Vibration resistance … No malfunction when tested with one sweep of 8.3 to 2000Hz in the axial direction and at a right angle to the main valve and armature, in both energized deenergized states. (Initial value)

Note 3) Value for high pressure type (1.5W) specificationsNote 4) Value for low power consumption (0.5W) specifications

Note 1)

64

5 Port Solenoid Valve Series VQ1000/2000

VQ1000/Flat Cable Kit with Terminal BlockStationsVV5Q11- G0-(D)

DimensionsL n

L1L2

(L3) (L4)

66.584

112.5123

7794.5125

135.5

87.5105125

135.5

98115.5137.5148

108.5126150

160.5

119136.5162.5173

129.5147175

185.5

140157.5187.5198

150.5168

187.5198

161178.5200

210.5

171.5189

212.5223

182199.5225

235.5

192.5210

237.5248

203220.5250

260.5

213.5231

262.5273

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Fomulae L1 = 10.5n + 45.5 L2 = 10.5n + 63 n: Stations (max. 16 stations)

Broken lines and dimensions inside ( ) indicate type [-D] (with DIN rail mounting bracket).

Series VQ1000/2000

65

VQ2000/Flat Cable Kit with Terminal BlockStationsVV5Q21- GU0-(D)

DimensionsL n

L1L2

(L3) (L4)

85119150

160.5

101135

162.5173

117151175

185.5

133167

187.5198

149183

212.5223

165199225

235.5

181215

237.5248

197231

262.5273

213247275

285.5

229263

287.5298

245279300

310.5

261295325

335.5

277311

337.5348

293327350

360.5

309343

362.5373

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Formulae L1 = 16n + 53 L2 = 16n + 87 n: Stations (max. 16 stations)

Broken lines and dimensions inside ( ) indicate type [-D] (with DIN rail mounting bracket).

66


VQ1000/Flat Cable KitStationsVV5Q11- J 0-(D)U

S

DimensionsL n

L1L2

(L3) (L4)

65.578.5112.5123

7689125

135.5

86.599.5125

135.5

97110

137.5148

107.5120.5150

160.5

118131

162.5173

128.5141.5175

185.5

139152

187.5198

149.5162.5187.5198

160173200

210.5

170.5183.5212.5223

181194225

235.5

191.5204.5225

235.5

202215

237.5248

212.5225.5250

260.5

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Formulae L1 = 10.5n + 44.5 L2 = 10.5n + 57.5 n: Stations (max. 16 stations)

4.8

7.7

18.7

(12)

(7.5

)

9.3

25

40.7

(35)

(5.5

)

40.5

66

93.5

= 2

(12) 13

(L4)

(L3)

L223.5

8.8

1.5

28 P = 10.5 27

L1

5.2

35

52

61.563.5

Applicable connector: Flat cable connector (20P)


2n-C3, C4, C6, M5

C3: One-touch fitting for ø3.2



M5: M5 threads

StationsD Side U Side1 2 3 4 5 6 7 8 n

4-M4 mounting hole

2-C8R(EXH) port

2-C8P(SUP) port

DIN rail clamping screw

Indicator light

Manual override

ABABABABAAA

A A A A A A A A

P

RR

SMC SMC SMC SMC SMC SMC SMC

XBBBBBBBBX

P

Broken lines and dimensions inside ( ) indicate type [-D] (with DIN rail mounting bracket) and horizontal connector entry [-JS].

Series VQ1000/2000

67

VQ2000/Flat Cable Kit

DimensionsL n

L1L2

(L3) (L4)

85100125

135.5

101116150

160.5

117132

162.5173

133148175

185.5

149164

187.5198

165180

212.5223

181196225

235.5

197212

237.5248

213228

262.5273

229244275

285.5

245260

287.5298

261276300

310.5

277292

312.5323

293308

337.5348

309324350

360.5

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Formulae L1 = 6n + 53 L2 = 16n + 68 n: Stations (max. 16 stations)

9.5

24.5

16

31.6

49

(7.5

)

(12)

23

41P = 16

(5.5

)

(35)

46.2

8010

.6

120

L2

(L3) (5.2)

(L4)

34.5

1

P = 16 34.5 6.5

1

L1

23.5Applicable connector: Flat cable connector (20P)


2n-C3, C4, C6, M5C3: One-touch fitting for ø3.2C4: One-touch fitting for ø4C6: One-touch fitting for ø6M5: M5 threads

StationsD side U side1 2 3 4 5 6 7 8 n

4-M5mounting hole

2-C10R(EXH) port

2-C10P(SUP) port

DIN railclamping screw

Manualoverride

Indicator light

A AA A A A A A

P

R

EXHEXH SMC SMC SMC SMC SMC SMC SMC

XBBBBBBBB

XP

R

(12) 13

35

52

73.5

StationsVV5Q21- J 0-(D) US

Broken lines and dimensions inside ( ) indicate type [-D] (with DIN rail mounting bracket) and horizontal connector entry [-JS].

Appr

ox. 4

68


B

D


VV5QG 0 J 1 1 08 C6 BU0

Kit designation

Base mounted plug-inSeries VQ1000

Stations02

…

2 stations

16 16 stations

…

Electrical entry

Cylinder port sizeWith One-touch fitting for ø3.2With One-touch fitting for ø4With One-touch fitting for ø6M5 threadsMixed and with port plugElbow top portedWith One-touch fitting for ø3.2Elbow top portedWith One-touch fitting for ø4Elbow top portedWith One-touch fitting for ø6M5 threadsElbow bottom portedWith One-touch fitting for ø3.2Elbow bottom portedWith One-touch fitting for ø4Elbow bottom portedWith One-touch fitting for ø6M5 threadsElbow with mixed port sizes

C3C4C6M5CM

L3

L4

L6

L5

B3

B4

B6

B5LM

Note 1)

U0 S00 — Flat cable kit with terminal block (20P) without cable

Flat cable kit (20P) without cable2 to 8 (16)

The minimum and maximum number of stations differ depending on the electrical entry.Refer to .

1

1

3

2

3

4

2


VQ 1 0 50 Y1

Series VQ1000

D

C

C

B

B

A

A12345

Manual overrideNil Non-locking push type (tool required)

Slotted locking type (tool required)Knob locking type (manual type)

BC

Seal type

Type of actuation

01

OptionsNil None

Back pressure check valve on all stations Note 2)

With DIN rail (Rail length: Standard) With DIN rail (Rail length: Special) Note 3) Regulator unit with 1 unit Note 4)



With ejector unit Note 5)

Special wiring specifications (except double wiring) Note 6) With name plateExternal pilot Note 7)


BD

DG1G2G3JKNRS

4

DC

(1.0W)

(1.5W)

(0.5W)


Series VQ1000/ Plug-in Unit

G kitJ kit

U side

D side

n

Stations

87654321

Topentry

Sideentry Kit Stations

2 position single2 position double 3 position closed center3 position exhaust center3 position pressure center

Specifications

Standard type

High pressure type

External pilot Low power consumption type

Symbol

Nil

H

R

Y


Function


Note 1) Indicate CM and LM in the specification table.

Note 2) Inch sizes use the following symbols.• N1: ø1/8"• N3: ø5/32"• N7: ø1/4"• N5T: 10-32UNF• NM: MixedTop ported elbows are LN and bottom ported elbows are BN.

Note 1) In case of two or more options, enter them in alphabetical order.Example) -BRS


Note 3) Indicate a special DIN rail length as “D” ( indicates stations).Example) -D08In this case, an eight station DIN rail will be provided regardless of the number of manifold stations.Indicate "-D0" for no DIN rail.

Note 4) Indicate regulator unit mounting stations in the specification table. Count as one unit, one station.

Note 5) Refer to page 35 for details when equipped with ejector unit.Also, "-J" and name plate "-N" cannot be combined.

Note 6) Be sure to indicate wiring specifications in the specification table.

Note 7) In case of an external pilot "R", indicate external pilot specification "R" for the applicable valve also.


Note 1) When specifying more than one item, enter symbols in alphabetical order.

69

Manifold Specification SheetSeries VQ1000/Plug-in UnitHow to Order Manifolds

VV5Q 1 1GJ

Base mountedplug-in

SeriesVQ1000

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Note 1)

Note 6)

Single

Double

Closed center

Pressure center

Exhaust center

Blanking plateVVQ1000-10A-1Individual SUP spacerVVQ1000-P-1-C6

Individual EXH spacerVVQ1000-R-1-C6

Back pressure check valve assemblyVVQ1000-18A

Regulator unitVVQ1000-AR-1

2 station matching fittingVVQ1000-52A-C8

Port plug Note 4)

Ejector unit Note 2)

SUP shut-off position: Indicate two locations.

EXH shut-off position: Indicate two locations.

SUP blocking plateVVQ1000-16AEXH shut-off position

C3 (N1)

C4 (N3)

C6 (N7)

M5

Val

ves

Specifications D side U side →

uses EXH block baseVVQ1000-19A--C

16


C3C4C6

346

Kit designation (Circle the selection.)

Note 5)

Company name

Contact person


Purchase order no.

Equipment name

Quantity

Date / /

∗ Enter an "X" in the required locations.

set(s) Required date


With One-touch fittingfor ø3.2 (ø1/8˝)

With One-touch fittingfor ø4 (ø5/32˝)


M5 threads

Sideported

Cyl

ind

er p

ort

siz

eE

nter

in c

ase

of m

ixed

siz

es(C

M a

nd L

M).


Single wiring

Double wiring



Applicable valves and optionsQty.


Order no.

Clerk (code no.)

Dept. code

Op

tion

s

←

Sideported

Sideported

Sideported

Note 3)

Not

es

Note 1) Indicate the shut-off position. The EXH passage is blocked on the D side of the EXH block base.Note 2) Refer to the separate catalog CAT.E138-A regarding the maximum number of ejector units.

Indicate station mounting positions from the U side, and also enter ejector and pressure switch part numbers.Note 3) Indicate stations for mounting regulator units. They are counted as one unit for one station, but a length of three stations is required. Indicate station

mounting positions from the D side.Note 4) When using port plugs, circle the specified ports.Note 5) When mounting an elbow fitting assembly (VVQ1000-F-L ), enter "L " in the table.Note 6) In case of single wiring or mixed wiring, connections to the connector terminals start from the A side solenoid of station 1 and continue in order without

skipping any terminals.

70

B

D


VV5Q 2 1 08 C6 B

Base mounted plug-inSeries VQ2000

02

…

16

…

Cylinder port sizeWith One-touch fitting for ø4With One-touch fitting for ø6With One-touch fitting for ø8Mixed and with port plugElbow top portedWith One-touch fitting for ø4Elbow top portedWith One-touch fitting for ø6Elbow top portedWith One-touch fitting for ø8Elbow bottom portedWith One-touch fitting for ø4Elbow bottom portedWith One-touch fitting for ø6Elbow bottom portedWith One-touch fitting for ø8Elbow with mixed port sizes

C4C6C8CM

L4

L6

L8

B4

B6

B8

LM

Note 1)

U0 S00 —

2 to 8 (16)

1

1

2

3

4

2


VQ 2 0 50 Y1

Series VQ2000

D

C

C

B

B

A

A12345

NilBC

01

OptionsNil None Note 2)

Back pressure check valve on all stationsWith DIN rail (Rail length: Standard) Note 3)

With DIN rail (Rail length: Special) Note 4) Special wiring specifications (except double wiring) With name plate Note 5)

External pilotBuilt-in silencer, Direct exhaust

BD

DKNRS

4

DC

(1.0W)

(1.5W)

Nil

H

R

(0.5W)Y


Series VQ2000/ Plug-in Unit

G kitJ kit

Note 1) For CM, indicate in the specification table.Note 2) Inch sizes use the following symbols.

• N3: ø5/32˝• N7: ø1/4˝• N9: ø5/16˝• NM: Mixed

Top ported elbows are LN and bottom ported elbows are BN.

Refer to .

n

8

7

6

5

4

3

2

1

G 0 J U0

Kit designation 3

Stations2 stations

16 stations


Flat cable kit with terminal block (20P) without cableFlat cable kit (20P) without cable

Topentry

Sideentry Kit, cable length Stations

U side

D side

Stations

Type of actuation2 position single2 position double 3 position closed center3 position exhaust center3 position pressure center

Function

Standard type

High pressure type

External pilot Low power consumption type

SpecificationsSymbol


Manual overrideNon-locking push type (tool required)Slotted locking type (tool required)Knob locking type (manual type)


Note 1) In case of two or more options, enter them in alphabetical order.

Example) -BRS


Note 3) Indicate a special DIN rail length as “D” ( indicates stations).

Example) -D08

In this case, an eight station DIN rail will be provided regardless of the number of manifold stations.

Indicate "-D0" for no DIN rail.


Note 5) In case of an external pilot "R", indicate external pilot specifications "R" for the applicable valve also.


Note 1) When specifying more than one item, enter symbols in alphabetical order.

71

Company name

Contact person


Purchase order no.

Equipment name

Quantity

VV5Q 2GJ1

Note 2)

Blanking plateVVQ2000-10A-1Individual SUP spacerVVQ2000-P-1-C8

Individual EXH spacerVVQ2000-R-1-C8

SUP shut-off position: Indicate two locations.

EXH shut-off position: Indicate two locations.

SUP blocking plateVVQ2000-16AEXH blocking plateVVQ2000-19ABack pressure check valve assemblyVVQ2000-18A

With One-touch fittingfor ø6 (ø1/4˝) With One-touch fittingfor ø8 (ø5/16˝)


Sideported

Sideported

Sideported

C4 (N3)

C6 (N7)

C8 (N9)

Op

tion

s

← →

Port plug Note 1)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


Single

Double

Closed center

Pressure center

Exhaust center

Val

ves

SpecificationsStationDescription/Model

Base mountedplug-in

SeriesVQ2000

Kit designation (Circle the selection.)

Ent

er in

cas

e of

mix

ed s

izes

(C

M).

Cyl

ind

er p

ort

siz

e


Single wiring

Double wiring



Order no.

Clerk (code no.)

Dept. code


Applicable valves and optionsQty.

Date / /

set(s) Required date

Manifold Specification SheetSeries VQ2000/Plug-in UnitHow to Order Manifolds

D side U side∗ Enter an "X" in the required locations.

NotesNote 1) When using port plugs, circle the specified ports.Note 2) In case of single wiring or mixed wiring, connections to the connector terminals start from the A side solenoid of station 1 and continue in order

without skipping any terminals.

72

Series PCW

Safety Instructions

Note 1) ISO 4414: Pneumatic fluid power -- Recommendations for the application of equipment to transmission and control systems

Note 2) JIS B 8370: General Rules for Pneumatic Equipment

Warning

Caution : Operator error could result in injury or equipment damage.

Warning : Operator error could result in serious injury or loss of life.

Danger : In extreme conditions, there is a possible result of serious injury or loss of life.

These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by a label of "Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 4414 Note 1), JIS B 8370 Note 2) and other safety practices.

1. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications.Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications or after analysis and/or tests to meet your specific requirements.

2. Only trained personnel should operate pneumatically operated machinery and equipment.Compressed air can be dangerous if handled incorrectly. Assembly, handling or repair of pneumatic systems should be performed by trained and experienced operators.

3. Do not service machinery/equipment or attempt to remove components until safety is confirmed.

1. Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions.

2. When equipment is to be removed, confirm the safety process as mentioned above. Cut the supply pressure for this equipment and exhaust all residual compressed air in the system.

3. Before machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston rod, etc. (Bleed air into the system gradually to create back pressure.)

4. Contact SMC if the product is to be used in any of the following conditions:1. Conditions and environments beyond the given specifications, or if product is used outdoors.2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical

equipment, food and beverages, recreation equipment, emergency stop circuits, press applications, or safety equipment.

3. An application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis.

73

1. This product is intended for use in general FA equipment. Avoid using this product in machinery or equipment which directly affects human lives or where malfunction or failure can cause extended damage.

2. Do not disassemble this product for repair or rebuilding.

1. Never use in an atmosphere of explosive gas-es.PC wiring system construction is not explosion proof. Never use in an atmosphere with explosive gases as this may cause a serious explosion.

2. Do not use in an environment with tempera-ture cycles.If PC wiring system units are used in locations with temperature cycles other than normal temperature changes, they may be adversely affected.

3. Do not use in an area where surges are gen-erated.When there is machinery or equipment (solenoid type lifter, high frequency induction furnace, motor, etc.) which generates a large amount of surge in the area around PC wiring system units and connected equipment, there is a danger of deteriora-tion or damage to the connected equipment. Take measures to protect against sources of surge generation and be careful of crossed lines.

4. Do not allow wiring scraps or other foreign matter to get into the terminal areas of this product.Do not allow wiring scraps or other foreign matter to get into the terminal areas of the PC wiring system units, as this can cause fire, failure or malfunction, etc.

5. Consider the operating environment and en-closure.Avoid use of PC wiring system units in locations where there is splash and spray of water or oil, etc.

1. Confirm the specifications.Use properly after confirming the specifications. Operation outside the range of specifications (voltage, ambient temperature, impact, etc.) can cause damage, malfunction or fire.

2. Ensure sufficient clearance for maintenance activities.When designing an application, be sure to allow sufficient clearance for maintenance and inspections.

1. Do not drop or bump.Do not drop, bump or apply excessive impacts (500m/s² or more) during handling. The PC wiring system unit can be dam-aged and connected equipment may malfunction.

2. Be careful of incorrect wiring.Incorrect wiring may result in damage to connected equipment. The power supply will be short circuited if inputs and outputs are connected incorrectly for the 8 point/16 point input/output units following a branch unit.

3. Do not wire with power lines or high voltage lines.To prevent the intrusion of noise and surge from power and high voltage lines into signal lines, perform wiring for the PC wiring system separately (separate conduits) from power lines and high voltage lines.

4. Confirm proper insulation of wiring.Faulty insulation (crossed wiring, insulation defects between terminals, etc.) may result in damage to connected equipment, due to the application of excessive voltage or current flowing to the equipment.

5. Tighten screws with the proper tightening torque.If tightened beyond the tightening torque range, the terminal block and screws may be damaged.

6. Avoid subjecting cables to repeated bending or pulling forces.Wiring installations which result in repeated bending stress and pulling force on cables can cause broken wires.

7. Note that the disposition of I/O addresses dif-fers for each PLC manufacturer.General purpose label sets (applicable to all manufacturers) are included, which can be cut as needed and inserted into the ter-minal label holders.

8. Operate within the rated current.The maximum current capacity for the power supply line on cir-cuit boards of all units is 2.0A. If the current passing through units such as the branch unit and input/output unit exceeds 2.0A, connect the power supply line to the same power supply terminal and do not allow current to pass through the circuit board.

Warning CautionOperation

Caution

Design & Selection

Mounting, Adjustment & Wiring

CautionOperating Environment

1. Perform periodic inspections to prevent unexpected malfunction.Unexpected malfunction or misoperation may make it impossible to assure safety.

2. Do not touch the terminals or internal circuit board when power is being applied.Touching parts such as the terminals or circuit board when power is being applied can cause malfunction or damage of the PC wiring system unit and connected equipment, and there is a danger of electrocution.

CautionMaintenance

Series PCWPC Wiring System PrecautionsBe sure to read before handling.

74

EUROPESPAIN/PORTUGALSMC España, S.A.

SWEDENSMC Pneumatics Sweden AB

SWITZERLANDSMC Pneumatik AG.

UKSMC Pneumatics (U.K.) Ltd.

ASIACHINASMC (China) Co., Ltd.

HONG KONGSMC Pneumatics (Hong Kong) Ltd.

INDIASMC Pneumatics (India) Pvt. Ltd.

MALAYSIASMC Pneumatics (S.E.A.) Sdn. Bhd.

PHILIPPINESSMC Pneumatics (Philippines), Inc.

SINGAPORESMC Pneumatics (S.E.A.) Pte. Ltd.SOUTH KOREASMC Pneumatics Korea Co., Ltd.

TAIWANSMC Pneumatics (Taiwan) Co., Ltd.

THAILANDSMC Thailand Ltd.

NORTH AMERICACANADASMC Pneumatics (Canada) Ltd.

MEXICOSMC Corporation (Mexico) S.A. de C.V.USASMC Pneumatics, Inc.

SOUTH AMERICAARGENTINASMC Argentina S.A.

BOLIVIASMC Pneumatics Bolivia S.R.L.

BRAZILSMC Pneumaticos Do Brazil Ltda.

CHILESMC Pneumatics (Chile) S.A.

VENEZUELASMC Neumatica Venezuela S.A.

OCEANIAAUSTRALIASMC Pneumatics (Australia) Pty. Ltd.

NEW ZEALANDSMC Pneumatics (N.Z.) Ltd.

EUROPEAUSTRIASMC Pneumatik GmbH

CZECHSMC Czech s.r.o.

DENMARKSMC Pneumatik A/S

FINLANDSMC Pneumatiikka OY

FRANCESMC Pneumatique SA

GERMANYSMC Pneumatik GmbH

HUNGARYSMC Hungary Kft.

IRELANDSMC Pneumatics (Ireland) Ltd.

ITALYSMC Italia S.p.A.

NETHERLANDSSMC Pnuematics BV.

NORWAYSMC Pneumatics Norway A/S

ROMANIASMC Romania s.r.l.

RUSSIA SMC Pneumatik LLC.

SLOVAKIASMC Slovakia s.r.o.

SLOVENIASMC Slovenia d.o.o.

SMC'S GLOBAL MANUFACTURING, DISTRIBUTION AND SERVICE NETWORK

1-16-4 Shimbashi, Minato-ku, Tokyo 105-0004, JAPANTel: 03-3502-2740 Fax: 03-3508-2480URL http://www.smcworld.com© 2000 SMC CORPORATION All Rights Reserved

Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.

Printed in Japan.1st printing March, 2000 D-SMC.L.A. P-80 (D)

Documents

PC Wiring System Series PCW - SMC ETechcontent2.smcetech.com/pdf/PCW.pdf · PC Wiring System Series Connection cable with connector P. 12 ... PC Wiring System Series PCW 1. ... Connected