Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
PFT-60 SideLite Transom Patch w/Stop Installation Instructions
Copyright © 2017, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited.
For Installation Assistance, Call 855.594.6989 • www.assaabloyglass.us
PFT-60 - 06/17
Tools Needed: Torque Wrench and Bit5mm Hex Wrench
Parts Included
NOT TO SCALE
Top Panel
SidePanel
PFT-60
{ Stop Tab
z Cover Plate
w Bushings (3)
y Screws (3)
x Bracket
v Bracket
u Cover Plate
| Blank Tabs (4)
PFT-60 Parts List1 Cover Plate2 Bracket3 Bushings (3)4 Bracket5 1 1/16" - M6 x 27 Screws (3)6 Cover Plate7 Stop Tab — PF-INS0028 Blank Tabs (4)
4 3/16"(106) 4 3/16"
(106)
2 1/16"(52)
2 1/16"(52)
Copyright © 2017, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. 2PFT-60 - 06/17
1.
2.
Prepare the Glass
Fasten Stop Tab• Gently pull back adhered gasket to remove blank tab & insert Stop Tab { onto
the appropriate bracket (v or x) depending on door configuration and swing.
DIAGRAM SHOWS BRACKET x APPLICATION ONLY.
Side Panel
Top Panel
2 7/8"(73)
1 3/8"(36)
1 3/8"(36)
1/8" (3)
1 3/8"(36)
1 3/8"(36)
Ø 13/16"(20)
Ø 13/16"(20)
Ø 13/16"(20)
x Bracket
{ Stop Tab
Caution: Office copiers, printers and facsimile machines may change the size of a drawing and make it inaccurate to use as a template.
USE FABRICATION SKETCH TO DRILL AND CUT GLASS.• Drill 13/16" (20 mm) diameter hole.
NOT TO SCALEDIMENSIONS IN INCHES (MILLIMETERS)
w Bushings (3)
y Screws (3)
x Bracket
v Bracket
3. Fasten Support BracketsMake sure the surface is thoroughly cleaned and remove all screws.• Insert the three Bushings w into prepped 13/16" (20 mm) diameter holes.• Place Bracket v into prepped area of glass, join Bracket x from the other side. Insert Screw y into Bracket x and tighten with 5 mm hex
wrench to hold Brackets together. Do not tighten completely to allow for adjustments throughout installation.• Insert two Screws y into Bracket v, align fitting to desired position. Torque both Screws to 12 nm. Then tighten Bracket x Screw to 12 nm.
Copyright © 2017, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. 3PFT-60 - 06/17
4. Adhere Cover Plates• Remove adhesive strip paper on both Brackets v & x to adhere Cover Plates u & z.• Hook Cover Plates u & zover hinge side locking pins.• Push in spring loaded locking pin on opposite side of Bracket.• Snap on Cover Plates.
v Bracket
z Cover Plate
u Cover Plate
PFT-60 - 06/17Copyright © 2017, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited.
USA: ASSA ABLOY Glass SolutionsRockwood, PA 15557Phone: 855.594.6989
www.assaabloyglass.us