Upload
ledien
View
227
Download
0
Embed Size (px)
Citation preview
PI-505
Option Printer
SERVICE MANUAL
Code Y111440-1
PUBLICATION ISSUED BY:
Olivetti S.p.A.77, Via Jervis - 10015 Ivrea (TO)Italy
Copyright © 2009, OlivettiAll rights reserved
PI-5
05O
UTL
INE
MA
INTE
NA
NC
EAD
JUST
MEN
T / S
ETTI
NG
Field Service Ver. 1.0 Jul. 2009
i
CONTENTS
PI-505
OUTLINE1. PRODUCT SPECIFICATIONS................................................................................ 1
MAINTENANCE2. PERIODICAL MAINTENANCE PROCEDURE ....................................................... 3
2.1 Paper feed section ................................................................................................ 3
2.1.1 Replacing the pick-up roller /Up and the feed roller /Up ............................... 3
2.1.2 Replacing the pick-up roller /Lw and the feed roller /Lw ............................... 5
2.1.3 Replacing the separation roller /Up and the torque limiter /Up ..................... 6
2.1.4 Replacing the separation roller /Lw and the torque limiter /Lw ..................... 7
3. OTHER MAINTENANCE ITEM ............................................................................... 8
3.1 Items not allowed to be disassembled and adjusted ............................................ 8
3.2 Disassembly/reassembly parts list........................................................................ 9
3.3 Cleaning parts list ................................................................................................. 9
3.4 Disassembly/reassembly procedure..................................................................... 9
3.4.1 Upper cover................................................................................................... 9
3.4.2 Rear cover................................................................................................... 10
3.4.3 Operation panel cover assy ........................................................................ 10
3.4.4 Post inserter ................................................................................................ 11
3.4.5 PI drive board (PIDB).................................................................................. 12
3.4.6 PI control board (PIOB)............................................................................... 13
3.5 Cleaning point..................................................................................................... 13
3.5.1 Pick-up roller /Up, feed roller /Up, separationroller /Up ............................... 13
3.5.2 Pick-up roller /Lw, feed roller /Lw, separationroller /Lw ............................... 14
3.5.3 Transport roller /Up ..................................................................................... 16
3.5.4 Transport roller /Lw ..................................................................................... 16
ADJUSTMENT/SETTING4. HOW TO USE THE ADJUSTMENT SECTION..................................................... 17
5. MECHANICAL ADJUSTMENT ............................................................................. 18
5.1 PI displacement adjustment (with PK-516 installed)........................................... 18
5.2 PI tilt adjustment (with PK-516 installed) ............................................................ 20
PI-5
05O
UTL
INE
MA
INTE
NA
NC
EAD
JUST
MEN
T / S
ETTI
NG
Field Service Ver. 1.0 Jul. 2009
ii
Blank Page
Field Service Ver. 1.0 Jul. 2009 1. PRODUCT SPECIFICATIONS
1
PI-5
05O
UTL
INE
OUTLINE1. PRODUCT SPECIFICATIONSA. Type
B. Functions
C. Paper type
D. Machine specifications
E. Operating environment• Conforms to the operating environment of the main body.
NOTE• These specifications are subject to change without notice.
Name Post inserter unit
Type Torque limiter separation type seat feeding device
Auto sheet feeding (online operation)
Feeds the sheet to finisher automatically under the instruction from the main body.
Manual sheet feeding (offline operation)
Feeds the sheet to finisher under the instruction from the operation panel of PI.You can select the following 5 post processing modes:• 1 staple/back mode• 2 staples (flat-stapling) mode• Punch mode (when PK-516 is installed on finisher)• Saddle stitching mode (when installed on SD-508)• Tri-folding mode (when installed on SD-508)
Size Tray /Up A4/A4S, B5/B5S, A58 1/2 x 11, 8 1/2 x 11S, 5 1/2 x 8 1/2, 7 1/4 x 10 1/2S, 16K, 16KSCustom paper (Max. 311.1 x 297 mm, Min. 182 x 139 mm)
Tray /Lw A3, B4, A4/A4S, B5/B5S, A58 x 13S, 8 1/4 x 13S, 8 1/2 x 13S, 8 1/8 x 13 1/4S, SRA4S, 12 x 18, 11 x 17, 8 1/2 x 14, 8 1/2 x 11, 8 1/2 x 11S, 5 1/2 x 8 1/2, 8K, 16K, 16KS, 7 1/4 x 10 1/2, 7 1/4 x 10 1/2SCustom paper (Max. 311.1 x 457.2 mm, Min. 182 x 139 mm)
Type Plain paper, recycle paper, color paper, special paper, coated paper, high-quality paper
Weight 64 g/m2 to 209 g/m2
Capacity Tray /Up 200 sheets (80 g/m2) or 30 mm or less in height
Tray /Lw 200 sheets (80 g/m2) or 30 mm or less in height
Power requirements DC 24 V, DC 5 V (supplied from the main body)
Max. power consumption
30 W or less
Dimensions511 mm (W) x 635 mm (D) x 220 mm (H)20 inch (W) x 25 inch (D) x 8.75 inch (H)
Weight 10.5 kg (23.25 lb)
Y111440-1 Service Manual
1. PRODUCT SPECIFICATIONS Field Service Ver. 1.0 Jul. 2009
2
PI-5
05O
UTL
INE
Blank Page
Service Manual Y111440-1
Field Service Ver. 1.0 Jul. 2009 2. PERIODICAL MAINTENANCE PROCEDURE
3
PI-5
05M
AIN
TEN
AN
CE
MAINTENANCE2. PERIODICAL MAINTENANCE PROCEDURE
2.1 Paper feed section
2.1.1 Replacing the pick-up roller /Up and the feed roller /Up
A. Periodically replaced parts/cycle• Pick-up roller /Up: Every 200,000 counts• Feed roller /Up: Every 100,000 counts
B. Replacing procedure1. Remove the upper cover.
See P.9
2. Remove two C-clips [1], and then slide two bearings [2] at the both sides and remove the feed roller assy /Up [3].
3. Remove the bearing [1] and removethe actuator [2].
A07VF2C500DA
[3]
[1][2] [1]
[2]
A07VF2C501DA
[1]
[2]
Y111440-1 Service Manual
2. PERIODICAL MAINTENANCE PROCEDURE Field Service Ver. 1.0 Jul. 2009
4
PI-5
05M
AIN
TEN
AN
CE
4. Remove two C-clips [1] and removetwo bearings [2].
5. Remove the C-clip [1].6. Slide two roller shafts [2] to the
arrow-marked direction to removethe pick-up roller /Up [3] and the feed roller /Up [4].
NOTE• Reinstalling the pick-up roller and
the feed roller with the blue faces of the one-way clutches of the pick-up roller and the feed roller face to the front.
7. Remove the pick-up roller [1] and the feed roller [2] from the one-way clutches [3] and [4].
NOTE• When reinstalling the pick-up roller
[1], be sure to insert its cutout [5] over the protrusion [6] of the one-way clutch [3].
• When reinstalling the feed roller [2], be sure to insert its cutout [7] over the protrusion [8] of the one-way clutch [4].
8. To reinstall, reverse the order of removal.
A07VF2C502DA[1]
[2]
A07VF2C503DA[1][4]
[3][2]
A07VF2C504DA
[3]
[1]
[5][7][2]
[8] [6][4]
Service Manual Y111440-1
Field Service Ver. 1.0 Jul. 2009 2. PERIODICAL MAINTENANCE PROCEDURE
5
PI-5
05M
AIN
TEN
AN
CE
2.1.2 Replacing the pick-up roller /Lw and the feed roller /Lw
A. Periodically replaced parts/cycle• Pick-up roller /Lw: Every 200,000 counts• Feed roller /Lw: Every 100,000 counts
B. Replacing procedure
1. Pull the release lever [1] and open the upper door [2].
2. Take steps 2 to 7 in the replacement procedure of the pick-up roller /Up and feed roller /Up.See P.3
3. To reinstall, reverse the order of removal.
A07VF2C505DA
[2]
[1]
Y111440-1 Service Manual
2. PERIODICAL MAINTENANCE PROCEDURE Field Service Ver. 1.0 Jul. 2009
6
PI-5
05M
AIN
TEN
AN
CE
2.1.3 Replacing the separation roller /Up and the torque limiter /Up
A. Periodically replaced parts/cycle• Separation roller /Up: Every 100,000 counts• Torque limiter /Up: Every 600,000 counts
B. Replacing procedure1. Remove the upper cover.
See P.9
2. Remove two C-clips [1], and then slide two bearings [2] at the both sides and remove the feed roller assy /Up [3].
3. Release hooks [1] at the both sides, and then lift up and remove the sep-aration roller assy /Up [2].
A07VF2C500DA
[3]
[1][2] [1]
[2]
A07VF2C506DA[1]
[2]
Service Manual Y111440-1
Field Service Ver. 1.0 Jul. 2009 2. PERIODICAL MAINTENANCE PROCEDURE
7
PI-5
05M
AIN
TEN
AN
CE
4. Remove the C-clip [1] and removethe separation roller /Up [2] and the torque limiter /Up [3].
NOTE• Install the separation roller with two
notches [4] face to the front and be aligned with the prong [5].
5. To reinstall, reverse the order of removal.
2.1.4 Replacing the separation roller /Lw and the torque limiter /Lw
A. Periodically replaced parts/cycle• Separation roller /Lw: Every 100,000 counts• Torque limiter /Lw: Every 600,000 counts
B. Replacing procedure
1. Pull the release lever [1] and open the upper door [2].
2. Take steps 2 to 4 in the replacement procedure of the separation roller /Up and torquelimiter /Up. See P.6
3. To reinstall, reverse the order of removal.
A07VF2C507DA
[5]
[3]
[4]
[2][1]
A07VF2C505DA
[2]
[1]
Y111440-1 Service Manual
3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009
8
PI-5
05M
AIN
TEN
AN
CE
3. OTHER MAINTENANCE ITEM
3.1 Items not allowed to be disassembled and adjusted
A. Paint-locked screwsNOTE• To prevent loose screws, a screw lock in blue or green series color is applied to
the screws.• The screw lock is applied to the screws that may get loose due to the vibrations
and loads created by the use of machine or due to the vibrations created during transportation.
• If the screw lock coated screws are loosened or removed, be sure to apply a screw lock after the screws are tightened.
B. Red-painted screwsNOTE• The screws which are difficult to be adjusted in the field are painted in red in order
to prevent them from being removed by mistake.• Do not remove or loosen any of the red-painted screws in the field. It should also
be noted that, when two or more screws are used for a single part, only one repre-sentative screw may be marked with the red paint.
C. Variable resistors on board
NOTE• Do not turn the variable resistors on boards for which no adjusting instructions
are given in Adjustment/Setting.
D. Removal of PWBs
CAUTION• When removing a circuit board or other electrical component, refer to “Handling of
PWBs” and follow the corresponding removal procedures.• The removal procedures given in the following omit the removal of connectors and
screws securing the circuit board support or circuit board.• Where it is absolutely necessary to touch the ICs and other electrical components
on the board, be sure to ground your body.
Service Manual Y111440-1
Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM
9
PI-5
05M
AIN
TEN
AN
CE
3.2 Disassembly/reassembly parts list
3.3 Cleaning parts list
3.4 Disassembly/reassembly procedure
3.4.1 Upper cover
1. Remove the cap [1].2. Remove four screws [2] and remove
the upper cover [3].
3. Reinstall the above parts following the removal steps in reverse.
Section Part name Ref. page
Exterior parts
Upper cover P.9
Rear cover P.10
Operation panel cover assy P.10
Unit Post inserter P.11
Board and etc.PI drive board (PIDB) P.12
PI control board (PIOB) P.13
Section Part name Ref. page
Feed section
Pick-up roller /Up P.13
Pick-up roller /Lw P.14
Feed roller /Up P.13
Feed roller /Lw P.14
Separation roller /Up P.13
Separation roller /Lw P.14
Transport sectionTransport roller /Up P.16
Transport roller /Lw P.16
A07VF2C508DA
[1][2]
[3]
Y111440-1 Service Manual
3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009
10
PI-5
05M
AIN
TEN
AN
CE
3.4.2 Rear cover
1. Remove the upper cover.See P.9
2. Remove the screw [1] and removethe connector cover [2].
3. Remove three screws [3] and remove the rear cover [4].
4. Reinstall the above parts following the removal steps in reverse.
3.4.3 Operation panel cover assy
1. Remove the upper cover.See P.9
2. Remove two screws [1], disconnect the connector [2] and remove the operation panel assy [3].
3. Reinstall the above parts following the removal steps in reverse.
A07VF2C509DA
[1][2]
[3]
[4]
A07VF2C510DA
[3]
[2]
[1]
Service Manual Y111440-1
Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM
11
PI-5
05M
AIN
TEN
AN
CE
3.4.4 Post inserter
1. Remove the screw [1] and removethe connector cover [2].
2. Open the front door of the finisher.3. Remove three screws [1].
4. Disconnect the connector [1].
A07VF2C511DA
[1]
[2]
A07VF2C512DA[1]
[1]
A07VF2C513DA
[1]
Y111440-1 Service Manual
3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009
12
PI-5
05M
AIN
TEN
AN
CE
5. Slide the post inserter [1] in the direction of arrow and remove it.
6. Reinstall the above parts following the removal steps in reverse.
3.4.5 PI drive board (PIDB)
1. Remove the rear cover.See P.10
2. Disconnect eight connectors [1] from the PI drive board.
3. Remove four board supports [1] and remove the PI drive board [2].
4. Reinstall the above parts following the removal steps in reverse.
A07VF2C514DB
[1]
A07VF2C001DA
[1]
[1]
A07VF2C002DA
[1]
[1][2]
Service Manual Y111440-1
Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM
13
PI-5
05M
AIN
TEN
AN
CE
3.4.6 PI control board (PIOB)
1. Remove the operation panel cover assy.See P.10
2. Remove two screws [1] and removethe PI control board [2].
3. Reinstall the above parts following the removal steps in reverse.
3.5 Cleaning point
NOTE• The alcohol described in the cleaning procedure of maintenance represents the
isopropyl alcohol.
3.5.1 Pick-up roller /Up, feed roller /Up, separationroller /Up
1. Remove the upper cover.See P.9
2. Using a cleaning pad dampened with alcohol, wipe the pick-up roller /Up [1] clean of dirt.
A07VF2C517DA[1]
[2]
A07VF2C518DA
[1]
Y111440-1 Service Manual
3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009
14
PI-5
05M
AIN
TEN
AN
CE
3. Using a cleaning pad dampened withalcohol, wipe the feed roller /Up [1] clean of dirt.
4. Remove the separation roller assy /Up.See P.6
5. Using a cleaning pad dampened withalcohol, wipe the separation roller /Up [1] clean of dirt.
3.5.2 Pick-up roller /Lw, feed roller /Lw, separationroller /Lw
1. Pull the release lever [1] and open the upper door [2].
A07VF2C519DA
[1]
A07VF2C520DA
[1]
A07VF2C505DA
[2]
[1]
Service Manual Y111440-1
Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM
15
PI-5
05M
AIN
TEN
AN
CE
2. Using a cleaning pad dampened with alcohol, wipe the pick-up roller /Lw[1] clean of dirt.
3. Using a cleaning pad dampened with alcohol, wipe the feed roller /Lw [1] clean of dirt.
4. Remove the separation roller assy /Lw.See P.6
5. Using a cleaning pad dampened with alcohol, wipe the separation roller /Lw [1] clean of dirt.
A07VF2C521DA
[1]
A07VF2C522DA[1]
A07VF2C523DA
[1]
Y111440-1 Service Manual
3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009
16
PI-5
05M
AIN
TEN
AN
CE
3.5.3 Transport roller /Up
1. Pull the release lever [1] and open the upper door [2].
2. Using a cleaning pad dampened withalcohol, wipe the transport roller /Up [1] clean of dirt.
3.5.4 Transport roller /Lw
1. Remove the post inserter.See P.11
2. Using a cleaning pad dampened withalcohol, wipe the transport roller /Lw[1] clean of dirt.
A07VF2C505DA
[2]
[1]
A07VF2C524DA
[1]
A07VF2C525DA[1]
Service Manual Y111440-1
Field Service Ver. 1.0 Jul. 2009 4. HOW TO USE THE ADJUSTMENT SECTION
17
PI-5
05AD
JUST
MEN
T / S
ETTI
NG
ADJUSTMENT/SETTING4. HOW TO USE THE ADJUSTMENT SECTION• “Adjustment/Setting” contains detailed information on the adjustment items and proce-
dures for this machine.• Throughout this “Adjustment/Setting,” the default settings are indicated by “ ”.
Advance checks• Before attempting to solve the customer problem, the following advance checks must be
made. Check to see if:
• The power supply voltage meets the specifications.• The power supply is properly grounded.• The machine shares the power supply with any other machine that draws large current
intermittently (e.g., elevator and air conditioner that generate electric noise).• The installation site is environmentally appropriate: high temperature, high humidity,
direct sunlight, ventilation, etc.; levelness of the installation site.• The original has a problem that may cause a defective image.• The density is properly selected.• The original glass, slit glass, or related part is dirty.• Correct paper is being used for printing.• The units, parts, and supplies used for printing (developer, PC drum, etc.) are properly
replenished and replaced when they reach the end of their useful service life.• Toner is not running out.
CAUTION• To unplug the power cord of the machine before starting the service job proce-
dures.• If it is unavoidably necessary to service the machine with its power turned ON, use
utmost care not to be caught in the scanner cables or gears of the exposure unit.• Special care should be used when handling the fusing unit which can be
extremely hot.• The developing unit has a strong magnetic field. Keep watches and measuring
instruments away from it.• Take care not to damage the PC drum with a tool or similar device.• Do not touch IC pins with bare hands.
Y111440-1 Service Manual
5. MECHANICAL ADJUSTMENT Field Service Ver. 1.0 Jul. 2009
18
PI-5
05AD
JUST
MEN
T / S
ETTI
NG
5. MECHANICAL ADJUSTMENT
5.1 PI displacement adjustment (with PK-516 installed)
• Conduct this adjustment when the punch position is displaced when feeding from PI.
NOTE• Punch hole deviation correction must be completed before making this adjust-
ment.See P.12 of the PK-516 service manual.
• Centering adjustment of the tray 1/2/3/4 must be completed before making this adjustment.
See P.649 of the main body service manual.See P.650 of the main body service manual.
• In the PI displacement adjustment, adjust the tray /Up, and then adjust the tray /Lw.
1. Set three sheets of paper in the tray of the PI, and then feed them in the punch mode as samples.
2. Fold the sheets in half at the center and check the misalignment of the punch holes.
<In the upper tray case>3. Release the hook [1], and remove
the adjustment cover [2].
<In the lower tray case>3. Remove the adjustment cover in the
same way as the upper tray case.Remove two screws [1], slide the side guide plate /Rr [2] to the front, and remove it.
A07VF3C503DA
[1]
[2]
A07VF3C504DA
[1]
[2]
Service Manual Y111440-1
Field Service Ver. 1.0 Jul. 2009 5. MECHANICAL ADJUSTMENT
19
PI-5
05AD
JUST
MEN
T / S
ETTI
NG
4. Loosen two adjustment screws [1] on the side guide plate /Rr [2] and slide the side guide plate /Rr twice as long as the misalignment of the punchhole position (for example, if the mis-alignment is 1.5 mm to the rear, slide 3 mm to the rear).1 index: 2 mm
5. Fully tighten the adjustment screws to secure the side guide plate /Rr.6. For the tray /Lw, reinstall the side guide plate /Rr with two screws.7. Repeat step 1 to 6 until the misalignment of the punch holes is corrected.8. Reinstall the adjustment cover.9. In the service mode, perform [Post Inserter Adjustment.].
See P.608 of the main body service manual.
A07VF3C505DA
[1]
[2]
Y111440-1 Service Manual
5. MECHANICAL ADJUSTMENT Field Service Ver. 1.0 Jul. 2009
20
PI-5
05AD
JUST
MEN
T / S
ETTI
NG
5.2 PI tilt adjustment (with PK-516 installed)
• Conduct this adjustment if the edge of the paper and the punch hole position of the paper fed from PI is not in parallel.
1. Set three sheets of paper in the tray of the PI, and then feed them in the punch mode as samples.
2. Fold the sheets in half and check the tilt of the punch holes.[1]: The front is wider[2]: The back is wider
3. Open the front door of finisher, and then loosen the screw [2] of the guide plate [1].
4. Adjust the guide plate [1] in accor-dance with the misalignment of the punch holes by referring to the mark [3].The back is wider: Move to [4]The front is wider: Move to [5]
5. Tighten the screw [2].
6. Repeat step 1 to 5 until the tilt of the punch holes is corrected.
A07VF3C501DA
[1] [2]
A07VF3C502DA
[1]
[2][4][5]
[3]
Service Manual Y111440-1
UPDATING STATUS
DATE UPDATED PAGES PAGES CODE
10/2009 1ST EDITION 25 Y111440-1