Upload
lasertech-modulos
View
254
Download
44
Tags:
Embed Size (px)
Citation preview
PIONEER CORPORATION 4-1, Meguro 1-chome,PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, LonPIONEER EUROPE NV Haven 1087, Keetberglaan 1, 912PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253
PIONEER CORPORATION 2005
DEH-2800MP/XN/UC
Meguro-ku, Tokyo 153-8654, Japang Beach, CA 90801-1760, U.S.A.
0 Melsele, BelgiumAlexandra Road, #04-01, Singapore 159936
ORDER NO.
CRT3554
HIGH POWER CD/MP3/WMA PLAYER WITH FM/AM TUNER
DEH-2800MP/XN/UC
DEH-2850MP/XN/ES
This service manual should be used together with the following manual(s):
Model No. Order No. Mech. Module Remarks
CX-3164 CRT3583 S10.5COMP1 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
For details, refer to "Important Check Points for Good Servicing".
K-ZZA. NOV. 2005 Printed in Japan
C
D
F
A
B
E
1 2 3 4SAFETY INFORMATION
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repaircomplex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do soand refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state ofCalifornia to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 - Proposition 65
- CD Section Precaution1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on mode may damage the ICs inside the unit.3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment (shorting-solder) by referring to "the DISASSEMBLY".4. After replacing the pickup unit, be sure to check the grating.
DEH-2800MP/XN/UC21 2 3 4
C
D
F
A
B
E
5 6 7 8
[Important Check Points for Good Servicing]In this manual, procedures that must be performed during repairs are marked with the below symbol.Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
DEH-2800MP/XN/UC 35 6 7 8
C
D
F
A
B
E
1 2 3 4
CONTENTS SAFETY INFORMATION..................................................................................................................................... 21. SPECIFICATIONS ............................................................................................................................................ 52. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 8
2.1 PACKING(DEH-2800MP/XN/UC)............................................................................................................... 82.2 PACKING(DEH-2850MP/XN/ES) ............................................................................................................. 102.3 EXTERIOR............................................................................................................................................... 122.4 CD MECHANISM MODULE..................................................................................................................... 14
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM.......................................................................................... 163.1 BLOCK DIAGRAM ................................................................................................................................... 163.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE).............................................................................. 183.3 KEYBOARD UNIT.................................................................................................................................... 243.4 CD MECHANISM MODULE(GUIDE PAGE) ............................................................................................ 26
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 364.1 TUNER AMP UNIT................................................................................................................................... 364.2 KEYBOARD UNIT.................................................................................................................................... 404.3 CD CORE UNIT(S10.5COMP1)............................................................................................................... 42
5. ELECTRICAL PARTS LIST ............................................................................................................................ 446. ADJUSTMENT ............................................................................................................................................... 48
6.1 CD ADJUSTMENT................................................................................................................................... 486.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 506.3 ERROR MODE ........................................................................................................................................ 526.4 SYSTEM MICROCOMPUTER TEST PROGRAM ................................................................................... 53
7. GENERAL INFORMATION............................................................................................................................. 547.1 DIAGNOSIS ............................................................................................................................................. 547.1.1 DISASSEMBLY ..................................................................................................................................... 547.1.2 CONNECTOR FUNCTION DESCRIPTION.......................................................................................... 577.2 PARTS...................................................................................................................................................... 587.2.1 IC .......................................................................................................................................................... 587.2.2 DISPLAY ............................................................................................................................................... 677.3 OPERATIONAL FLOW CHART ............................................................................................................... 68
8. OPERATIONS ................................................................................................................................................ 69
DEH-2800MP/XN/UC41 2 3 4
C
D
F
A
B
E
5 6 7 81. SPECIFICATIONS
DEH-2800MP/XN/UC 55 6 7 8
C
D
F
A
B
E
1 2 3 4
DEH-2800MP/XN/UC61 2 3 4
DEH-2800MP/XN/UC 7
5 6 7 8
5 6 7 8
C
D
F
A
B
E
C
D
F
A
B
E
1 2 3 42. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING(DEH-2800MP/XN/UC)
NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. • The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. • Screw adjacent to mark on the product are used for disassembly. • For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.)
"
161
9
54
2
3
14
DEH-2800MP/XN/UC81 2 3 4
C
D
F
A
B
E
5 6 7 8
PACKING(DEH-2800MP/XN/UC) SECTION PARTS LIST
Owner's Manual,Installation Manual
Mark No. Description Part No.
1 Accessory Assy CEA4610
2 Screw Assy CEA6002
3 Fixing Screw(M2 x 4) CBA1994
4 Screw CBA1650
* 5 Polyethylene Bag CEG-127
6 Screw CRZ50P090FTC
7 Screw TRZ50P080FTC
* 8 Polyethylene Bag CEG-158
9 Handle CNC5395
10 Bush CNV3930
11 Polyethylene Bag CEG1173
12 Carton CHG5633
13 Contain Box CHL5633
14 Protector CHP2664
15 Protector CHP2868
16-1 Owner's Manual CRD4027
16-2 Installation Manual CRD4028
16-3 Caution Card CRP1310
* 16-4 Warranty Card CRY1247
17 Cord Assy XDE7008
Mark No. Description Part No.
Part No. Language
CRD4027 English, French, Spanish
CRD4028 English, French, Spanish
DEH-2800MP/XN/UC 95 6 7 8
C
D
F
A
B
E
1 2 3 42.2 PACKING(DEH-2850MP/XN/ES)
15
18
11
12
13
1616
10
9
8
75
4
2
17
14
DEH-2800MP/XN/UC101 2 3 4
C
D
F
A
B
E
5 6 7 8
PACKING(DEH-2850MP/XN/ES) SECTION PARTS LIST
Owner's Manual,Installation Manual
Mark No. Description Part No.
1 Accessory Assy CEA4850
2 Screw Assy CEA3849
3 •••••
4 Screw CBA1650
* 5 Polyethylene Bag CEG-127
6 Screw CRZ50P090FTC
7 Screw TRZ50P080FTC
* 8 Polyethylene Bag CEG-158
9 Handle CNC5395
10 Bush CNV3930
11 Polyethylene Bag CEG-162
12 Carton CHG5631
13 Contain Box CHL5631
14 Protector CHP2664
15 Protector CHP2868
16-1 Owner's Manual CRD4029
16-2 Installation Manual CRD4030
16-3 Caution Card CRP1310
17 Cord Assy XDE7008
18 Case Assy CXB3520
Mark No. Description Part No.
Part No. Language
CRD4029 English, Spanish, Portuguese(B), Traditional Chinese, Arabic
CRD4030 English, Spanish, Portuguese(B), Traditional Chinese, Arabic
DEH-2800MP/XN/UC 115 6 7 8
C
D
F
A
B
E
1 2 3 42.3 EXTERIOR
DEH-2800MP/XN/UC121 2 3 4
C
D
F
A
B
E
5 6 7 8
(1) EXTERIOR SECTION PARTS LIST
(2) CONTRAST TABLEDEH-2800MP/XN/UC and DEH-2850MP/XN/ES are constructed the same except for the following:
Mark No. Description Part No.
1 Screw BSZ26P060FTC
2 Screw BSZ26P100FTC
3 Cord Assy XDE7008
4 •••••
5 Cable CDE7985
6 Case CNB2793
7 Holder CNC8659
8 Insulator CNM9145
9 Tuner Amp Unit See Contrast table(2)
10 Screw ASZ26P060FTC
11 Screw BMZ26P160FTC
12 Screw BPZ26P080FTC
> 13 Fuse(10 A) CEK1208
14 Pin Jack(CN352) CKB1059
15 Plug(CN901) CKM1376
16 Connector(CN831) CKS3581
17 Connector(CN651) CKS3834
18 •••••
19 Antenna Jack(CN401) CKX1056
20 Holder CND2414
21 Holder CND2413
22 Heat Sink CNR1762
23 FM/AM Tuner Unit CWE1952
24 Holder CND1054
25 Button(DETACH) CAC4836
26 Spring CBH1835
27 Spring CBH2208
28 Spring CBH2367
29 Bracket CNC6791
30 Holder CNC8042
31 Cover CNM6276
32 Panel CNS8404
33 Arm CNV4692
34 Arm CNV4728
35 Arm CNV5576
36 Screw IMS20P030FTB
37 Detach Grille Assy See Contrast table(2)
38 Screw BPZ20P100FTB
39 Button(DETACH) CAC9382
40 Button(VOLUME(+/ -)) See Contrast table(2)
41 Button(CLOCK,1-6,LOCAL/BSM,AUDIO) CAC9385
42 Button(↑,→,EJECT) CAC9386
43 Button(↓,←) CAC9387
44 Button(EQ,DISPLAY) CAC9388
45 Button(SOURCE,BAND) See Contrast table(2)
46 Spring CBH2210
47 Cover CNS8367
48 LCD See Contrast table(2)
49 Connector(CN1801) CKS3580
50 Holder CND2949
51 Transistor(Q911,921,991) 2SD2396
52 IC(IC302) PAL007B
53 Lighting Conductor CNV8712
54 Rubber CNV8713
55 Connector CNV8714
56 Grille Unit See Contrast table(2)
57 Chassis Unit CXC3600
58 CD Mechanism Module(S10.5) CXK5752
59 Panel See Contrast table(2)
Mark No. Description Part No.
Mark No. Description DEH-2800MP/XN/UC DEH-2850MP/XN/ES9 Tuner Amp Unit CWN1275 CWN1276
37 Detach Grille Assy CXC5244 CXC524540 Button(VOLUME(+/ -)) CAC9751 CAC9383
45 Button(SOURCE, BAND) CAC9752 CAC9384 48 LCD CAW1906 CAW1905
56 Grille Unit CXC5277 CXC5279 59 Panel CNS8389 CNS8385
DEH-2800MP/XN/UC 135 6 7 8
C
D
F
A
B
E
1 2 3 42.4 CD MECHANISM MODULE
DEH-2800MP/XN/UC141 2 3 4
C
D
F
A
B
E
5 6 7 8
CD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description Part No.
1 CD Core Unit(S10.5COMP1) CWX3176
2 Connector(CN101) CKS4182
3 Connector(CN901) CKS5284
4 Screw BMZ20P025FTC
5 Screw BSZ20P040FTC
6 Screw(M2 x 3) CBA1511
7 Screw(M2 x 4) CBA1835
8 Washer CBF1038
9 •••••
10 Spring CBH2609
11 Spring CBH2612
12 Spring CBH2614
13 Spring CBH2616
14 Spring CBH2617
15 Spring CBH2620
16 Spring CBH2855
17 Spring CBH2937
18 Spring CBH2735
19 Spring CBH2854
20 Spring CBH2642
21 Spring CBH2856
22 Spring CBH2857
23 Spring CBH2860
24 Spring CBH2861
25 Spring CBL1686
26 Arm CND1909
27 Frame CND2582
28 Bracket CND2583
29 Arm CND2584
30 Lever CND2585
31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV7201
36 Gear CNV7207
37 Gear CNV7208
38 Gear CNV7209
39 Gear CNV7210
40 Gear CNV7211
41 Gear CNV7212
42 Rack CNV7214
43 Arm CNV7216
44 Roller CNV7218
45 Gear CNV7219
46 Guide CNV7361
47 Gear CNV7595
48 Guide CNV7799
49 Arm CNV7805
50 Rack CNV8342
51 Roller CNV8343
52 Holder CNV8344
53 Arm CNV8345
54 Guide CNV8347
55 Arm CNV8348
56 Arm CNV8349
57 Arm CNV8350
58 Clamper CNV8365
59 Arm CNV8386
60 Guide CNV8396
61 Arm CNV8413
62 Collar CNV8938
63 Motor Unit(M2) CXC4026
64 Arm Unit CXC4027
65 Chassis Unit CXC4028
66 Gear Unit CXC4029
67 Frame Unit CXC4031
68 Motor Unit(M1) CXC6742
69 Screw Unit CXC6359
70 Screw JFZ20P020FTC
71 Screw JGZ17P022FTC
72 Washer YE20FTC
73 Pickup Unit(P10.5)(Service) CXX1942
74 Screw IMS26P030FTC
Mark No. Description Part No.
DEH-2800MP/XN/UC 155 6 7 8
C
D
F
A
B
E
1
E
2
SYSTEM
ICP
1 2 3 4
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM3.1 BLOCK DIAGRAM
PICKUP UNIT(P10.5)(SERVICE) D CD CORE UNIT(S10.5COMP1)C
BRST,BRXEN,BSRQ
CN901
Q101
M
LASERDIODE
MONITORDIODE
S903DSCSNS
SPINDLEMOTOR
MCARRIAGEMOTOR
LOAD/
LD-
MD
15
5
HOLOGRAM UNIT
IC301BA5835FP
IC201UPD63763CGJ
RF-AMP,CD DECODER, MP3 , WMA, DECODER,
DIGITAL SERVO / DATA PROCESSOR
CDDRIVER
1VD
VD
16LOUT
11
CN101
16SOP
15SOM
18LCOP
17LCOM
22LOEJ
31LOUT
9CONT
TD,FD
AC,BD
F,E
SD,MD
S901HOME
S90412EJ
S9058EJ
LD+ 14
142LD
143PD
12EJ
CONT
LOEJ
HOME
32
42
40
47
VDD
IC203NJM2886DL3-33
+3.3V REGULATOR
V3R3D 34
VDCONT49
CD CONTROLLER
IC701PE5505A
39CDMUTE
2
V3R3D
9
BDATA,BSCK
Q701
43/CD3VON
VDD
15
5
FOCUS ACT.TRACKING ACT.
FOP
TOP21 TOP
FOP
11 FOP14 TOP
21
14
VD
VDCONT
13
12
X701
X1
X28EJ
31
DSCSNS30
SWVDD
14RESET8
10/RESETCDMUTE
88VREFREFO 133
REFOUT
33FOM
LOCK/RFOK
FOM
12 FOM
44TOM TOM
13 TOM
21CLCONT CLCONT41
46CD3VON
1
4.00MHz
35
34
X201
XTAL
/XTAL16.93MHz
XRST,XASTB,ADO,XCK,XSO,XSI,WAIT,XINT
56
63
LOCK
TUN_Lch
CD_Lch
CN4011
2
CN651
TUNER AMP UNIT
LOUT
A
TUN 3.3V
VCC(SYS 8V)
VDD
ANTENNA
TU
NP
DI
TU
NP
CK
TU
NP
DO
BRST,BRXEN,BSRQ
BDATA,BSCKCD VD
VD
VDCONT
5
20
12
10
1311
B.UP
Q991
19Q992
VDD
RESETNC
36
FM/AM TUNER UNIT
FMRF
ANT adjRF adj
FM ANT
T51 CF52
RFG
ND
OS
CG
ND
DG
ND
AU
DIO
GN
D
NC
VC
C
VD
D_3
.3
3.3V 2.5VIC 4
3.3V 2.5V
←
IC 22.5V
NC
CE
2
RO
M_V
DD SL DI
CK
CE
1
NC
DO
NC
NC
NC
NC
7 6 13 5 10 9 8 11 14 18 19 20 21
1
3
2 12 15 22 16 4 17
IC 13.3V
AM ANT FMRFATT
LPFOSC
IC 3 EEPROM5.0V
IC 55V 3.3V←
ATT
MIXER, IF AMP DET, FM MPX
24
23
Rch
Lch
DEH-2800MP/XN/UC161 2 3 4
C
D
F
A
B
E
TU
CD
36
5 6 7 8
FL-
FL+
RL-RL+
3
9
11
12
10
1
6
2
BACK UP
GND
FUSE
10A
ACC
B. REM
7Rear_ L
IN1-L
IN2-L
1
IC151PML014A
ELECTRONIC VOLUME/SOURCE SELECTOR
N_Lch
2_Lch
6Front_ L
60
BSENS
ASENS
VDD
B.UP
63
64
48MUTE
23
21
3
5
FL-
FL+
RL-
RL+
BREM
ACC
RLIn12
22
4
POWER AMP
IC601(1/2)PE5518A
SYSTEM CONTROLLER
IC963BD4834G
IC302PAL007B(50W)
VDD
Q911
Q931
SYSPW
VDD
STBYMUTE
IC1801PD6340A
LCD DRIVER/KEY CONTROLLER
5
7
CN1801CN831Q801
KEYBOARD UNIT
VC
K, V
DT
, VS
T
43SYSPW
Q452(1/2)
Q452(2/2)
MUTE
B.UP
Q821
18
20
DPDT
KYDT
LCD
MUTE
SYSTEM CONTROLLER
25BREM
VDD REGULATOR
BACKUP SENSE
ACC SENSE
3
9
11
12
10
1
6
2
B
CN901
TUNPCE1
TUNPCE2
TUNPDI
RE
SE
T
TUNPDO
SL
56
55
11
12
76
TUNPCK13
TUNPDO
TUN3V
TUN 3V REG.
B.UP
SYS 8V REG.
TUNPDI
CE1
CE2
SL
TUNPCK
Q912
DALMON32
B.UP
VCC(SYS 8V)
6,20
6
4
8
3
5
7
6
4
8
3
SOURCE
5.1VSWVDD
SRC
DSENS
ILM
DPDT
KYDT
S1805SWVDD
21
66
DSENS65
ILMPW22
DPDT9
KYDT8
RLch
CN352
2
FLIn14
Q822
DSENS
SOURCE
SWVDD
BSENS
ASENS
X1
X2
70
X60112.58291MHz69
KEY DATAX0
X1
22
X18015MHz23
Q352
KEY MATRIX
EJECT
S1819S1829
BANDS1820
AUDIO
S1818S1838
DISP/LOUD
S1826S1827
VOL-S1807
CLOCK
S1809S1839
6ch/PAUSES1811
LOCS1810
LEFT
S1813S1821
RIGHT
S1816S1824
4ch/RDMS1812
UP
S1815S1823
DOWN
S1814S1822
5ch/RPTS1802
BTB
S1803S1825
3chS1804
VOL+
S1801
2ch
S1806
RESET
IC601(2/2)PE5518A
IC901NJM2885DL1-33
SW5V
SOURCE
DPDT
KYDT
ILL
1chS1808
VCC
1 3
SWVDD
ILMPW
MUTE
1 2
Q921
Q923
NC
DEH-2800MP/XN/UC 175 6 7 8
C
D
F
A
B
E
STRKEY2
1 2 3 4
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)
A-aA-a A-b A-b
A-aA-a A-b A-b
A-b A-b A-a A-a
Large sizeSCH diagram
Guide page
Detailed page
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST".
A-a
A
R60268K(DEH-2800MP/XN/UC)NM(DEH-2850MP/XN/ES)
R60133K(DEH-2800MP/XN/UC)47K(DEH-2850MP/XN/ES)
B CN1801
C CN901
Decimal points for resistorand capacitor fixed valuesare expressed as :2.2 2R20.022 R022
← ←
The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.
Symbol indicates a resistor.No differentiation is made between chip resistors anddiscrete resistors.
NOTE :
Symbol indicates a capacitor.No differentiation is made between chip capacitors anddiscrete capacitors.
CD
RE
SE
T
SO
UR
CE
DEH-2800MP/XN/UC181 2 3 4
C
D
F
A
B
E
A-a A-b
A-a A-b
A-b A-a
C CN901
SO
UR
CE
5 6 7 8
A-b
A
CEK1208 10A
>
>
A TUNER AMP UNIT
600µH
CD
RE
SE
T
STRKEY2
DEH-2800MP/XN/UC 195 6 7 8
C
D
F
A
B
E
1 2 3 4
A-a
A-b
A-a
A-a
A-b 1 2 3
R60
268
K(D
EH
-280
0MP
/XN
/UC
)N
M(D
EH
-285
0MP
/XN
/ES
)
R60
133
K(D
EH
-280
0MP
/XN
/UC
)47
K(D
EH
-285
0MP
/XN
/ES
)
CC
N90
1 SOURCE
DEH-2800MP/XN/UC201 2 3 4
C
D
F
A
B
E
33K
(DE
H-2
800M
P/X
N/U
C)
47K
(DE
H-2
850M
P/X
N/E
S)
5 6 7 8
A-a
A-b
A-a
A-a
A-b4
BC
N18
01
Dec
imal
poi
nts
for
resi
stor
and
capa
cito
r fix
ed v
alue
sar
e ex
pres
sed
as :
2.2
2R
20.
022
R
022
←
←
The
> m
ark
foun
d on
som
e co
mpo
nent
par
ts in
dica
tes
the
impo
rtan
ce o
f the
saf
ety
fact
or o
f the
par
t.T
here
fore
, whe
n re
plac
ing,
be
sure
to u
se p
arts
of
iden
tical
des
igna
tion.
Sym
bol i
ndic
ates
a r
esis
tor.
No
diffe
rent
iatio
n is
mad
e b
etw
een
chip
res
isto
rs a
nddi
scre
te r
esis
tors
.
NO
TE
: Sym
bol i
ndic
ates
a c
apac
itor.
No
diffe
rent
iatio
n is
mad
e b
etw
een
chip
cap
acito
rs a
nddi
scre
te c
apac
itors
.
CDRESET
ST
RK
EY
2
DEH-2800MP/XN/UC 215 6 7 8
C
D
F
A
B
E
1 2 3 4
A-a
A-b
A-b 1 2 3
CE
K12
0810
A
>
>
AT
UN
ER
AM
P U
NIT
600µ
H
DEH-2800MP/XN/UC221 2 3 4
C
D
F
A
B
E
CE
K12
0810
A
5 6 7 8
A-a
A-b
A-b4
>
600µ
H
DEH-2800MP/XN/UC 235 6 7 8
C
D
F
A
B
E
1 2 3 43.3 KEYBOARD UNIT
B
LCD DRIVER
B KEYBOARD UNIT
DEH-2800MP/XN/UC241 2 3 4
C
D
F
A
B
E
5 6 7 8
B
LCD : CAW1906(DEH-2800MP/XN/UC)CAW1905(DEH-2850MP/XN/ES)
A CN831
DEH-2800MP/XN/UC 255 6 7 8
C
D
F
A
B
E
NC
NC
NC
NC
1 2 3 4
3.4 CD MECHANISM MODULE(GUIDE PAGE)
C-a
C
M1 CXC6742SPINDLE MOTOR
M2 CXC4026LOADING/CARRIAGE MOTOR
PICKUP UNIT(P10.5)(SERVICE)
CD DRIVER
SWITCHES:CD CORE UNIT(S10.5COMP1) S901:HOME SWITCH..........ON-OFF S903:DSCSNS SWITCH......ON-OFF S904:12EJ SWITCH.............ON-OFF S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
F
F
T
T
FTCS
FTCS
T
T
F
F
TF
FT
F
T
F
S
C
S S C C
F
T
T
S
S
C
C
8
9
3
2
1
@
$
!
#
4
6
7
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
DEH-2800MP/XN/UC261 2 3 4
C
D
F
A
B
E
5 6 7 8
C-b
C
CD CORE UNIT(S10.5COMP1)C
FSIGNAL LINE
FOCUS SERVO LINE
TRACKING SERVO LINE
CARRIAGE SERVO LINE
SPINDLE SERVO LINE
T
C
S
A CN651
+ 3.3 V REGULATOR
CD CONTROLLER
0
^
5
%
NC
SRAMLEVEL0
SRAMLEVEL1
ADENA
SRAMLEVEL2
CD3VON(MCKRQ)
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
(S905)
(S904)
DEH-2800MP/XN/UC 275 6 7 8
C
D
F
A
B
E
The
und
erlin
ed in
dica
tes
the
switc
h po
sitio
n.
1 2 3 4
A-a
C-b
C-a
C-a
C-b 1
PIC
KU
P U
NIT
(P10
.5)(
SE
RV
ICE
)
SW
ITC
HE
S:
CD
CO
RE
UN
IT(S
10.5
CO
MP
1)
S90
1:H
OM
E S
WIT
CH
......
....O
N-O
FF
S
903:
DS
CS
NS
SW
ITC
H...
...O
N-O
FF
S
904:
12E
J S
WIT
CH
......
......
.ON
-OF
F
S90
5:8E
J S
WIT
CH
......
......
...O
N-O
FF
F FT T
F
T
C
S
F
T
C
S
TTFF
T F F T
@
$
!
DEH-2800MP/XN/UC281 2 3 4
C
D
F
A
B
E
SW
ITC
HE
S:
CD
CO
RE
UN
IT(S
10.5
CO
MP
1)
S90
1:H
OM
E S
WIT
CH
......
....O
N-O
FF
5 6 7 8
A-a
C-b
C-a
C-a
C-b2 3
M1
CX
C67
42S
PIN
DLE
MO
TO
R
M2
CX
C40
26LO
AD
ING
/CA
RR
IAG
E M
OT
OR
CD
DR
IVE
R
S
903:
DS
CS
NS
SW
ITC
H...
...O
N-O
FF
S
904:
12E
J S
WIT
CH
......
......
.ON
-OF
F
S90
5:8E
J S
WIT
CH
......
......
...O
N-O
FF
The
und
erlin
ed in
dica
tes
the
switc
h po
sitio
n.
F
T F
S
C
S
S
C
C
F T T
S S C C
8 9
3 2 1
#
4
6 7
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
DEH-2800MP/XN/UC 295 6 7 8
C
D
F
A
B
E
1 2 3 4
C-a
C-b
C-b 1
CD
CO
RE
UN
IT(S
10.5
CO
MP
1)C
FS
IGN
AL
LIN
E
FO
CU
S S
ER
VO
LIN
E
TR
AC
KIN
G S
ER
VO
LIN
E
CA
RR
IAG
E S
ER
VO
LIN
E
SP
IND
LE S
ER
VO
LIN
E
T C S
+ 3.
3 V
RE
GU
LAT
OR
0
DEH-2800MP/XN/UC301 2 3 4
C
D
F
A
B
E
5 6 7 8
C-a
C-b
C-b2 3
AC
N65
1
CD
CO
NT
RO
LLE
R
^
5
%
NC
SR
AM
LEV
EL0
SR
AM
LEV
EL1
AD
EN
A
SR
AM
LEV
EL2
CD
3VO
N(M
CK
RQ
)
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
(S90
5)
(S90
4)
DEH-2800MP/XN/UC 315 6 7 8
C
D
F
A
B
E
1 2 3 4
- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.2. Reference voltage REFO1(1.65 V)
1 DSCSNS2 8SNS3 12SNS
5 V/div5 V/div5 V/div
500 ms/div
12 cm CD Loading operation
Ref.:GND
Mode:Normal
1 DSCSNS2 8SNS3 12SNS
5 V/div5 V/div5 V/div
500 ms/div
Ref.:GND
Mode:Normal
1 DSCSNS4 CLCONT5 VD
5 V/div5 V/div10 V/div
500 ms/div
12 cm CD Loading operation 8 cm CD Loading operation
Ref.:GND
Mode:Normal
9 FIN0 RFOK6 SIN
200 mV/div2 V/div2 V/div
500 ms/div
12 cm CD-DA Source On setup operation
Ref.:REFO
Mode:Normal
@ FE9 FIN! TE8 TIN
500 mV/div500 mV/div500 mV/div500 mV/div
20 ms/div
Ref.:REFO
Mode:Normal
! TE@ FE
500 mV/div500 mV/div
200 ms/div
Source On setup operation CD-DA Play operation
Ref.:REFO
Mode:Normal
@ FE9 FIN! TE8 TIN
500 mV/div500 mV/div500 mV/div500 mV/div
20 ms/div
CD-ROM play operation(Regular track Jump)
Ref.:REFO
Mode:Normal
# MDX6 SIN
2 V/div500 mV/div
5 µs/div
Ref.:REFO
Mode:Normal
# MDX6 SIN
2 V/div200 mV/div
50 ms/div
Spindle waveform during play operation Spindle waveform during play operation(Wider)
Ref.:REFO
Mode:Normal
6 SIN7 CIN8 TIN
1 V/div500 mV/div500 mV/div
1 s/div
12 cm CD-DA setup operation after loading 12 cm CD-ROM(3 sessions) setup operation after loading
Ref.:REFO
Mode:Normal
6 SIN7 CIN8 TIN
1 V/div500 mV/div500 mV/div
1 s/div
Ref.:REFO
Mode:Normal
6 SIN7 CIN8 TIN
1 V/div500 mV/div500 mV/div
1 s/div
12 cm CD-ROM(1 session) setup operation after loading
Ref.:REFO
Mode:Normal
DEH-2800MP/XN/UC321 2 3 4
C
D
F
A
B
E
5 6 7 8
9 FIN@ FE
500 mV/div500 mV/div
200 ms/div
Focus Search waveform
Ref.:REFO
Mode:TEST
$ RFAGC! TE8 TIN
1 V/div500 mV/div500 mV/div
500 µs/div
Ref.:REFO
Mode:TEST
! TE$ RFAGC
500 mV/div500 mV/div
2 ms/div
Track Open waveform 1 Track Jump waveform
Ref.:REFO
Mode:TEST
$ RFAGC! TE7 CIN6 SIN
1 V/div1 V/div500 mV/div2 V/div
200 ms/div
Ref.:REFO
Mode:Normal
Search operation(Outter to Inner)
% LOUT^ ROUT
1 V/div1 V/div
200 µs/div
Analog audio waveform
Ref.:AGND
Mode:Normal
6 SIN7 CIN8 TIN
1 V/div500 mV/div500 mV/div
500 ms/div
Ref.:REFO
Mode:Normal
1 DSCSNS2 8SNS3 12SNS
5 V/div5 V/div5 V/div
500 ms/div
12 cm CD Eject operation
CD-DA → CD-ROM mode change(Band key)
Ref.:GND
Mode:Normal
$ RFAGC! TE8 TIN
1 V/div500 mV/div500 mV/div
500 µs/div
4 Tracks Jump waveform 32 Tracks Jump waveform
Ref.:REFO
Mode:TEST
$ RFAGC! TE8 TIN
1 V/div500 mV/div500 mV/div
2 ms/div
Ref.:REFO
Mode:TEST
$ RFAGC! TE8 TIN
1 V/div500 mV/div500 mV/div
1 ms/div
10 Tracks Jump waveform
Ref.:REFO
Mode:TEST
1 DSCSNS5 CLCONT4 LOEJ
5 V/div5 V/div5 V/div
500 ms/div
12 cm CD Eject operation
Ref.:GND
Mode:Normal
1 DSCSNS2 8SNS3 12SNS
5 V/div5 V/div5 V/div
500 ms/div
8 cm CD Eject operation
Ref.:GND
Mode:Normal
DEH-2800MP/XN/UC 335 6 7 8
C
D
F
A
B
E
1 2 3 4
6 SIN7 CIN8 TIN
1 V/div500 mV/div500 mV/div
500 ms/div
CD-ROM → CD-DA mode change(Band key)
Ref.:REFO
Mode:Normal
$ RFAGC8 TIN! TE9 FIN
1 V/div1 V/div1 V/div1 V/div
500 µs/div
Black dot(800 µm) during play
Ref.:REFO
Mode:Normal
DEH-2800MP/XN/UC341 2 3 4
DEH-2800MP/XN/UC 35
5 6 7 8
5 6 7 8
C
D
F
A
B
E
C
D
F
A
B
E
1 2 3 44. PCB CONNECTION DIAGRAM4.1 TUNER AMP UNIT
A
A TUNER AMP UNIT
CapacitorConnector
P.C.Board Chip PartSIDE B
SIDE A
NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- gram.2.Viewpoint of PCB diagrams
CN651
B CN1801
C CN901
CORD ASSY
1
5
15
2
10
20
32
1
DEH-2800MP/XN/UC361 2 3 4
C
D
F
A
B
E
5 6 7 8
A
SIDE A
FRONT
ANTENNA JACKREAR OUTPUT
FM
/AM
TU
NE
R U
NIT
1 42 3
2
1
DEH-2800MP/XN/UC 375 6 7 8
C
D
F
A
B
E
1 2 3 4
A
A TUNER AMP UNIT
IC151
TESTPCL
DEH-2800MP/XN/UC381 2 3 4
C
D
F
A
B
ETEST
5 6 7 8
A
SIDE B
IC963
1
DEH-2800MP/XN/UC 395 6 7 8
C
D
F
A
B
E
1 2 3 44.2 KEYBOARD UNIT
B
B KEYBOARD UNIT B KEYBOARD UNITSIDE A SIDE B
D1810
R1815
R1814
R1813
R1812
R1808 R1809
R1807
R18
11
A CN831
VO
L+
VO
L-
EQ
DIS
P/L
OU
D
CLO
CK
1ch
2ch
3ch
4ch/
RD
M5c
h/R
PT
6ch/
PA
US
ELO
C
DO
WN
LEF
TR
IGH
T
UP
EJE
CT
SO
UR
CE
AU
DIO
BA
ND
DEH-2800MP/XN/UC401 2 3 4
DEH-2800MP/XN/UC 41
5 6 7 8
5 6 7 8
C
D
F
A
B
E
C
D
F
A
B
E
1 2 3 44.3 CD CORE UNIT(S10.5COMP1)
C
C CD CORE UNIT(S10.5COMP1) SIDE A
IC301IC203
20
CN901
PICKUP UNIT(P10.5)(SERVICE)
ACN651
M2LOADING
/CARRIAGEMOTOR
M1SPINDLEMOTOR
F
E
REFO1
HOME
DEH-2800MP/XN/UC421 2 3 4
C
D
F
A
B
E
5 6 7 8
C
C CD CORE UNIT(S10.5COMP1) SIDE B
DSCSNS
8EJ12EJ
DEH-2800MP/XN/UC 435 6 7 8
C
D
F
A
B
E
1 2 3 45. ELECTRICAL PARTS LIST
NOTE:• Parts whose parts numbers are omitted are subject to being not supplied.• The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS.....• The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. • Meaning of the figures and others in the parentheses in the parts list. Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No.
Unit Number : CWN1275(DEH-2800MP/
XN/UC)
Unit Number : CWN1276(DEH-2850MP/
XN/ES)
Unit Name : Tuner Amp Unit
Unit Number :
Unit Name : Keyboard Unit
Unit Number : CWX3176
Unit Name : CD Core
Unit(S10.5COMP1)
AUnit Number : CWN1275(DEH-2800MP/
XN/UC)Unit Number : CWN1276(DEH-2850MP/
XN/ES)Unit Name : Tuner Amp Unit
MISCELLANEOUS
IC 151 (B,133,80) IC PML014AIC 302 (A,94,135) IC PAL007BIC 601 (B,87,62) IC PE5518AIC 901 (B,143,29) IC NJM2885DL1-33IC 963 (B,62,83) IC BD4834G
Q 352 (B,160,129) Transistor UMH3NQ 452 (B,139,128) Transistor UMD2NQ 801 (B,80,29) Transistor 2SA1036KQ 821 (B,43,15) Transistor 2SA1036KQ 822 (B,31,17) Transistor DTC114EU
Q 911 (A,8,116) Transistor 2SD2396Q 912 (B,9,128) Transistor UMD2NQ 921 (A,8,103) Transistor 2SD2396Q 923 (B,24,79) Transistor UMD2N
Q 931 (B,61,107) Transistor UMX1N
Q 991 (A,8,69) Transistor 2SD2396Q 992 (B,21,58) Transistor UMD2ND 551 (A,62,124) Diode MPG06G-6415G3D 552 (A,59,124) Diode MPG06G-6415G3D 901 (A,35,131) Diode MPG06G-6415G3
D 902 (A,35,128) Diode MPG06G-6415G3D 911 (A,21,106) Diode MPG06G-6415G3D 912 (A,18,120) Diode HZS6L(B2)D 921 (A,24,87) Diode HZS9L(B3)D 931 (A,69,115) Diode HZS7L(C3)
D 932 (A,54,108) Diode HZS7L(A1)D 961 (A,56,74) Diode 1SS133D 991 (A,20,66) Diode HZS7L(C3)L 151 (A,146,93) Inductor LAU2R2KL 401 (A,157,58) Inductor LAU2R2K
L 402 (A,148,88) Inductor LAU2R2KL 404 (B,160,101) Inductor LCTAW220J2520L 601 (A,93,85) Ferri-Inductor LAU100KL 602 (A,103,67) Inductor LAU2R2KL 651 (A,41,38) Ferri-Inductor LAU100K
L 801 (A,88,25) Inductor LAU2R2KL 901 (A,36,108) Choke Coil 600µH CTH1280X 601 (A,103,71) Radiator 12.58291MHz CSS1402>FU352 (B,143,135) Fuse 3A CEK1286> Fuse 10A CEK1208
AR401 (A,161,110) Arrester DSP-201M-S00BFM/AM Tuner Unit CWE1952
RESISTORS
R 301 (B,93,104) RS1/16S153JR 353 (B,144,128) RS1/16S821JR 354 (B,164,128) RS1/16S821JR 357 (B,145,133) RS1/16S223JR 358 (B,164,135) RS1/16S223J
R 405 (B,155,62) RS1/16S681JR 407 (B,159,87) RAB4C681JR 414 (B,159,91) RS1/16S681JR 420 (B,99,48) RS1/16S681JR 421 (B,160,79) RS1/16S473J
Circuit Symbol and No. Part No.
DEH-2800MP/XN/UC441 2 3 4
C
D
F
A
B
E
5 6 7 8
R 454 (B,135,127) RS1/16S103JR 455 (B,140,130) RS1/16S153JR 456 (B,140,133) RS1/16S221JR 457 (B,99,50) RS1/16S681JR 601 (B,100,58) (DEH-2800MP/XN/UC) RS1/16S333J
R 601 (B,100,58) (DEH-2850MP/XN/ES) RS1/16S473JR 602 (B,109,58) (DEH-2800MP/XN/UC) RS1/16S683JR 606 (B,111,61) RS1/16S104JR 607 (B,107,61) RS1/16S222JR 608 (B,106,74) RS1/16S0R0J
R 609 (B,102,43) RS1/16S473JR 610 (B,99,52) RS1/16S681JR 612 (B,106,57) RS1/16S103JR 613 (B,72,54) RS1/16S104JR 633 (B,53,73) RS1/16S104J
R 650 (B,50,50) RS1/16S102JR 651 (B,58,36) RS1/16S104JR 652 (B,60,38) RS1/16S102JR 655 (A,76,51) RD1/4PU102JR 659 (B,84,43) RS1/16S221J
R 660 (B,93,46) RS1/16S681JR 662 (B,102,40) RS1/16S682JR 663 (B,81,43) RS1/16S682JR 670 (B,76,54) RS1/16S104JR 671 (B,79,43) RS1/16S104J
R 801 (B,77,29) RS1/16S153JR 802 (B,95,25) RS1/16S153JR 803 (B,104,23) RS1/16S222JR 821 (B,34,18) RS1/16S562JR 822 (B,74,29) RS1/16S102J
R 823 (B,38,15) RS1/16S103JR 833 (A,80,17) RD1/4PU222JR 834 (A,82,17) RD1/4PU222JR 835 (A,68,20) RD1/4PU102JR 836 (A,72,26) RD1/4PU104J
R 837 (A,78,25) RD1/4PU103JR 838 (B,89,89) RS1/16S102JR 841 (B,52,15) RS1/16S1R0JR 848 (A,105,46) RD1/4PU102JR 851 (A,103,46) RD1/4PU102J
R 852 (B,91,89) RS1/16S102JR 911 (B,11,124) RS1/16S183JR 912 (A,8,131) RD1/4PU152JR 913 (B,18,110) RS1/16S0R0JR 923 (A,19,90) RD1/4PU821J
R 931 (B,65,112) RS1/16S473JR 932 (B,65,110) RS1/16S104JR 933 (A,55,116) RD1/4PU102JR 934 (B,61,110) RS1/16S472JR 935 (B,55,106) RS1/16S473J
R 936 (B,57,110) RS1/16S223JR 940 (B,86,81) RS1/16S104JR 941 (B,89,81) RS1/16S104JR 961 (B,67,78) RS1/16S102JR 962 (B,62,78) RS1/16S183J
R 991 (A,20,61) RD1/4PU271JR 992 (A,15,68) RD1/4PU221J
CAPACITORS
Circuit Symbol and No. Part No.C 151 (B,160,73) CKSRYB224K10C 152 (B,160,75) CKSRYB224K10C 153 (B,130,69) CKSRYB105K6R3C 154 (B,142,74) CKSRYB105K6R3C 165 (B,136,91) CKSRYB104K16
C 166 (A,134,92) CEJQ470M10C 167 (A,128,92) CEJQ100M16C 301 (B,119,108) CKSQYB474K16C 302 (B,128,111) CKSQYB474K16C 303 (B,131,122) CKSQYB474K16
C 304 (B,123,107) CKSQYB474K16C 305 (B,119,113) CKSRYB474K10C 306 (B,131,114) CKSRYB474K10C 307 (B,134,124) CKSRYB474K10C 308 (B,126,109) CKSRYB474K10
C 309 (B,136,132) CKSQYB225K10C 310 (B,137,136) CKSQYB225K10C 312 (A,104,125) CEJQ100M16C 313 (B,100,142) CKSRYB104K16C 353 (A,134,120) CEJQ2R2M50
C 354 (A,134,110) CEJQ2R2M50C 401 (B,160,69) CKSRYB103K50C 402 (B,154,59) CKSRYB103K50C 403 (A,151,58) CEJQ470M6R3C 404 (A,151,95) CEJQ101M10
C 405 (B,167,97) CKSRYB103K50C 409 (B,147,56) CCSRCH470J50C 410 (B,122,15) CKSRYB102K50C 420 (B,108,43) CCSRCH470J50C 451 (A,132,132) CEJQ330M10
C 601 (B,69,83) CKSRYB103K50C 604 (B,98,75) CCSRCH200J50C 605 (B,102,75) CCSRCH200J50C 608 (B,91,48) CCSRCH101J50C 610 (A,101,82) CEJQ4R7M35
C 613 (B,100,78) CKSRYB105K6R3C 651 (B,42,40) CKSRYB105K10C 670 (B,44,42) CCSRCH221J50C 801 (B,104,25) CKSRYB105K6R3C 832 (B,49,13) CKSRYB104K16
C 901 (A,36,140) CEAT332M16(P45)C 911 (A,16,96) CEJQ470M10C 912 (B,12,133) CKSRYB103K50C 913 (A,19,137) CEAT331M16C 921 (A,25,66) 330µF/16V CCH1326
C 922 (A,24,82) CEJQ101M16C 923 (B,23,85) CKSRYB103K50C 961 (B,56,85) CKSRYB473K50C 962 (B,60,75) CKSRYB105K6R3C 981 (B,135,25) CKSRYB334K10
C 983 (A,144,38) CEJQ470M10C 991 (B,17,63) CKSRYB473K50C 992 (A,17,54) CEJQ101M10
BUnit Number :Unit Name : Keyboard Unit
MISCELLANEOUS
Circuit Symbol and No. Part No.
DEH-2800MP/XN/UC 455 6 7 8
C
D
F
A
B
E
1 2 3 4
IC 1801 (B,32,100) IC PD6340AD 1803 (A,43,67) LED SML-310PTD 1804 (A,43,79) LED SML-310PTD 1805 (A,43,91) LED SML-310PTD 1806 (A,28,29) LED SML-310PT
D 1807 (A,43,39) LED SML-310PTD 1808 (A,43,55) LED SML-310PTD 1809 (A,28,42) LED SML-310PTD 1810 (A,29,50) LED NESW505C-5273D 1812 (A,17,12) LED SML-310PT
D 1813 (A,31,12) LED SML-310PTD 1814 (A,12,154) LED SML-310PTD 1815 (A,17,168) LED SML-310PTD 1816 (A,31,168) LED SML-310PTD 1817 (A,43,127) LED SML-310PT
D 1818 (A,43,115) LED SML-310PTD 1819 (A,43,103) LED SML-310PTD 1820 (A,28,136) LED SML-310PTD 1821 (A,22,144) LED SML-310PTD 1823 (A,42,140) LED SML-310PT
D 1824 (A,33,144) LED SML-310PTD 1825 (A,28,152) LED SML-310PTX 1801 (B,39,90) Ceramic Resonator 5.00MHz CSS1547
LCD(DEH-2800MP/XN/UC) CAW1906LCD(DEH-2850MP/XN/ES) CAW1905
RESISTORS
R 1801 (B,28,66) RS1/16S222JR 1802 (B,30,66) RS1/16S222JR 1807 (B,27,29) RS1/4SA471JR 1808 (B,31,42) RS1/4SA471JR 1809 (B,24,42) RS1/4SA681J
R 1810 (B,42,98) RS1/16S104JR 1811 (B,21,29) RS1/4SA681JR 1812 (B,30,123) RS1/4SA471JR 1813 (B,35,128) RS1/4SA471JR 1814 (B,32,133) RS1/4SA681J
R 1815 (B,40,136) RS1/4SA471J
CAPACITORS
C 1801 (B,42,102) CKSRYB103K50C 1802 (A,28,45) CKSRYF104Z25
CUnit Number : CWX3176Unit Name : CD Core
Unit(S10.5COMP1)
MISCELLANEOUS
IC 201 (B,39,70) IC UPD63763CGJIC 203 (A,12,16) IC NJM2886DL3-33IC 301 (A,28,18) IC BA5835FPIC 701 (A,32,48) IC PE5505AQ 101 (B,60,89) Transistor 2SA1577
Q 701 (B,24,41) Transistor UN2111X 201 (B,28,57) Ceramic Resonator 16.934MHz CSS1603X 701 (A,24,37) Ceramic Resonator 4.000MHz CSS1652S 901 (A,57,57) Switch(HOME) CSN1067S 903 (B,23,78) Switch(DSCSNS) CSN1067
Circuit Symbol and No. Part No.
S 904 (B,42,87) Switch(12EJ) CSN1068S 905 (B,28,88) Switch(8EJ) CSN1068
RESISTORS
R 101 (B,61,92) RS1/10SR2R4JR 102 (B,63,92) RS1/10SR2R4JR 103 (B,63,89) RS1/10SR2R7JR 104 (A,52,73) RS1/16SS102JR 201 (B,44,57) RS1/16SS102J
R 202 (A,38,62) RS1/16SS473JR 203 (A,37,62) RS1/16SS473JR 214 (A,46,79) RS1/16SS472JR 216 (A,46,81) RS1/16SS472JR 221 (A,44,81) RS1/16SS103J
R 222 (A,45,81) RS1/16SS103JR 225 (B,52,78) RS1/16SS103JR 226 (B,52,77) RS1/16SS393JR 227 (A,44,75) RS1/16SS562JR 228 (A,46,72) RS1/16SS122J
R 229 (A,44,72) RS1/16SS472JR 232 (A,46,75) RS1/16SS122JR 241 (B,26,63) RS1/16SS333JR 243 (B,26,62) RS1/16SS333JR 245 (B,26,69) RS1/16SS333J
R 248 (B,55,74) RS1/16SS105JR 307 (A,19,20) RS1/16SS183JR 308 (A,17,20) RS1/16SS183JR 309 (A,18,18) RS1/16SS183JR 310 (A,17,16) RS1/16SS183J
R 601 (B,30,47) RS1/16S101JR 602 (B,28,50) RS1/16S101JR 606 (B,20,54) RS1/16S0R0JR 701 (B,26,44) RS1/16SS221JR 707 (B,32,45) RS1/16SS473J
R 709 (A,36,35) RS1/16SS222JR 710 (B,41,46) RS1/16SS102JR 712 (A,45,57) RS1/16SS222JR 713 (B,40,57) RS1/16SS222JR 716 (B,29,37) RS1/16SS472J
R 724 (B,31,36) RS1/16S473JR 726 (B,23,47) RS1/16SS103JR 727 (B,31,42) RS1/16SS473JR 729 (B,20,48) RS1/16SS223JR 730 (B,20,46) RS1/16SS473J
R 740 (A,38,59) RS1/16SS222JR 746 (A,13,38) RS1/16SS104JR 750 (A,40,66) RS1/16SS473JR 902 (A,20,36) RS1/16SS221JR 905 (A,21,36) RS1/16SS221J
R 906 (B,20,36) RS1/16SS221JR 907 (B,16,62) RS1/16SS0R0JR 908 (B,16,64) RS1/16SS0R0JR 911 (B,20,32) RS1/16SS0R0J
CAPACITORS
C 103 (B,57,83) CEVW101M16C 108 (A,47,66) CKSSYB104K10C 201 (B,46,56) CKSSYB102K50C 202 (B,47,58) CKSSYB104K10
Circuit Symbol and No. Part No.
DEH-2800MP/XN/UC461 2 3 4
C
D
F
A
B
E
5 6 7 8
C 204 (B,35,48) CEVW220M6R3
C 205 (A,34,63) CKSSYB104K10C 208 (B,34,54) CKSSYB104K10C 209 (B,31,57) CKSSYB104K10C 210 (A,31,66) CKSRYB105K10C 216 (B,53,77) CKSSYB332K50
C 217 (B,52,79) CKSSYB104K10C 218 (B,52,76) CKSSYB473K10C 219 (B,52,74) CKSSYB104K10C 220 (A,46,77) CKSSYB182K50C 221 (B,51,74) CKSSYB104K10
C 222 (A,46,73) CCSSCH560J50C 223 (A,44,74) CCSSCH4R0C50C 224 (B,52,68) CKSSYB104K10C 225 (A,47,67) CKSSYB103K16C 226 (A,49,67) CCSSCH680J50
C 227 (A,48,65) CCSSCH470J50C 228 (A,46,62) CKSSYB103K16C 232 (A,12,31) CKSRYB105K10C 237 (A,31,67) CKSSYB104K10C 239 (A,46,74) CCSSCH220J50
C 246 (A,42,80) CKSSYB104K10C 250 (A,42,81) CKSRYB102K50C 251 (A,41,83) CKSRYB102K50C 303 (A,18,20) CKSSYB472K25C 304 (A,17,17) CKSSYB103K16
C 307 (A,34,15) CKSSYB104K10C 308 (A,17,30) CKSRYB105K10C 601 (B,25,50) CCSRCH102J50C 602 (B,26,51) CCSRCH102J50C 701 (B,25,47) CKSSYB104K10
C 703 (B,28,42) CKSSYB103K16C 706 (B,34,43) CKSSYB104K10C 707 (A,36,57) CKSSYB104K10C 714 (A,24,41) CKSSYB104K10C 722 (B,29,45) CKSQYB475K6R3
C 903 (B,14,54) CKSSYB471K50C 907 (B,14,62) CKSSYB103K16
Miscellaneous Parts List
Pickup Unit(P10.5)(Service) CXX1942M 1 Motor Unit(SPINDLE) CXC6742M 2 Motor Unit(LOADING/CARRIAGE) CXC4026
Circuit Symbol and No. Part No.
DEH-2800MP/XN/UC 475 6 7 8
C
D
F
A
B
E
1 2 3 4
6. ADJUSTMENT6.1 CD ADJUSTMENT
1) Cautions on adjustments• In this product the single voltage (3.3V) is used for the regulator. The reference voltage is the REFO1 (1.65V) instead of the GND.If you should mistakenly short the REFO1 with the GND during adjustment, accurate voltage will not be obtained, and the servo’s misoperation will apply excessive shock to the pickup. To avoid such problems:a. Do not mix up the REFO1 with the GND when connecting the (-) probe of measuring instruments. Especially on an oscilloscope, avoid connecting the (-) probe for CH1 to the GND. b. In many cases, measuring instruments have the same potential as that for the (-) probe. Be sure to set the measuring instruments to the floating state.c. If you have mistakenly connected the REFO1 to the GND, turn off the regulator or the power immediately.
• Before mounting and removing filters or leads for adjustment, be sure to turn off the regulator.
• For stable circuit operation, keep the mechanism operating for about one minute or more after the regulator is turned on.
• In the test mode, any software protections will not work. Avoid applying any mechanical or electrical shock to the mechanism during adjustment.
• The RFI and RFO signals with a wide frequency range are easy to oscillate. When observing the signals, insert a resistor of 1k ohms in series.
• The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it.
2) Test modeThis mode is used to adjust the CD mechanism module.• To enter the test mode.While pressing the 4 and 6 keys at the same time, reset.• To exit from the test mode.Turn off the ACC and back up.
Notes:a. During ejection, do not press any other keys than the EJECT key until the loaded disc is ejected.b. If you have pressed the (→) key or (←) key during focus search, turn off the power immediately to protect the actuator from damage caused by the lens stuck.c. For the TR jump modes except 100TR, the track jump operation will continue even if the key is released.d. For the CRG move and 100TR jump modes, the tracking loop will be closed at the same time when the key is released.e. When the power is turned off and on, the jump mode is reset to the single TR (91), the RF amp gain is set to 0dB, and the auto-adjustment values are reset to the default settings.
DEH-2800MP/XN/UC481 2 3 4
C
D
F
A
B
E
5 6 7 8
[Key]
Contents
Display
[4] + [6] + Reset or[4] + [6] + BU + ACC
Test Mode In
[CD] or [SOURCE]
Source On
TRK MIN SEC
[BAND]
Power On(T.Offset is adjusted)TRK MIN SEC00 00 00
[3]
Power On(T.Offset is not adjusted)
99 99 99
[2]
RF AMPGain switching
GG GG GG
*1[4]
SPINDLESpeed switching
SP SP SP
*9
[3]
Focus CloseS curve check
TRK MIN SEC91 91 91
[6]
Focus Mode switching
0X 0X 0X
*2
[1]
Tracking ServoClose
00 00 00or 99 99 99
[>]
CRG +
[2]
Self-adjustingswitching
TRK MIN SEC?? ?? ??
*3*8
[<]
CRG -*8
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[1]T.Close & AGC
Applicable servomechanism
TRK MIN SEC?tr ?min ?sec
[6] [3]
RF AGC /RF AGC coefficient display
[>]
CRG +
8X 8X 8Xor 9X 9X 9X
[2]
T.Balance adjustment /T.BAL coefficient display
TRK MIN SEC?? ?? ??
[<]
CRG -T.CloseApplicable servomechanism
?? ?? ??
[1]
F,T,RF AGCF.Bias display switchingTRK MIN SEC
TRK MIN SEC
TRK MIN SEC
TRK MIN SEC?tr ?min ?sec
TRK MIN SEC
[3] [6]
CRG/TR jumpvalue switching
[>]
CRG/TR Jump +
[2]
Tracking Open
[<]
CRG/TR Jump -
?tr ?min ?sec
TRK MIN SEC
TRK MIN SEC
TRK MIN SEC?tr ?min ?sec
00 00 00or 99 99 99
TRK MIN SEC
TRK MIN SEC?tr ?min ?sec
8X 8X 8Xor 9X 9X 9X
8X 8X 8Xor 9X 9X 9X
00 00 00or 99 99 99
TRK MIN SEC?tr ?min ?sec?? ?? ??
*7 F,T AGC / F.BiasRF AGC
8X 8X 8Xor 9X 9X 9X
[2]
Tracking Open
*6
*5
*4 *4
Operation[Key] Test Mode
[BAND] Power On/Off[>] CRG + / TR Jump +
(Direction of the external surface)[<] CRG - / TR Jump -
(Direction of the internal surface)[1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting[2] RF Gain switching / Offset adjustment display /
T.Balance adjustment / T. Open[3] F. Close,S Curve / Rough Servo and RF AGC /
F,T,RF AGC[4] SPDL 1X/2X switching
As for the double speed(2x), audio output cannot besupported.
[5] Error Rate measurementON : ERR 30Counts StartBER display data[%]
[6] F. Mode switching / Tracking Close / CRG•TRJump Switching
*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).• In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
*10
TRK MIN SEC
[5]
Gop ModeGop Mode switching
OL OL OL
- Flow Chart
*1) TYP → + 6 dB → + 12 dB TRK MIN SEC TRK06MIN06SEC06 TRK12MIN12SEC12
*2) Focus Close → S Curve check setting → F EQ measurement setting TRK00MIN00SEC00
TRK01MIN01SEC01 TRK02MIN02SEC02 (TRK99MIN99SEC99)
*3) F.Offset Display → RF.Offset → T.Offset Display → Switch to the order of the original display
*4) 1TR/4TR/10TR/32TR/100TR*5) Single → 4TR → 10TR → 32TR → 100TR → CRG Move 9x(8x):91(81) 92(82) 93(83) 94(84) 95(85) 96(86)
*6) Only at the time of CRG move, 100TR jump
*7) TRK/MIN/SEC → F.AGC → T.AGC Gain → F.Bias → RF AGC
*8) CRG motor voltage = 2 [V]
*9) TYP (1X) → 2X → 1X TRK MIN SEC
TRK22MIN22SEC22 TRK11MIN11SEC11*10) OFF(TYP) → FORCUS → TRACKING TRK MIN SEC
TRK70MIN70SEC70 TRK71MIN71SEC71
• As for the double speed (2x), audio output cannot be supported
DEH-2800MP/XN/UC 495 6 7 8
C
D
F
A
B
E
1 2 3 4
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT
CD CORE UNIT(S10.5COMP1)
• Note :The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below.
• Purpose :To check that the grating is within an acceptable range when the PU unit is changed.
• Symptoms of Mal-adjustment :If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching.
• Method :
• Measuring Equipment• Measuring Points
• Oscilloscope, Two L.P.F.• E, F, REFO1
• Disc • TCD-782• Mode • TEST MODE
• Checking Procedure1. In test mode, load the disc and switch the 3V regulator on.2. Using the → and ← buttons, move the PU unit to the innermost track.3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the fourth press.4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75° . Refer to the photographs supplied to determine the phase angle.5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the mechanism should be judged to be at fault.• NoteBecause of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle.
• HintReloading the disc changes the clamp position and may decrease the "wobble".
100kΩ
390pF
100kΩ
390pF
E
VREF
F
VREF
Xch Ych
L.P.F.
L.P.F.
OscilloscopeF
EREFO1
DEH-2800MP/XN/UC501 2 3 4
C
D
F
A
B
E
5 6 7 8
Grating waveform
45°
0°
75°
60°
30°
90°
Ech → Xch 20mV/div, ACFch → Ych 20mV/div, AC
DEH-2800MP/XN/UC 515 6 7 8
C
D
F
A
B
E
1 2 3 4
6.3 ERROR MODE
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing.
(1) Basic Indication Method
1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains in blank as before.
2) Head unit display examples
Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.
8-digit display 6-digit display 4-digit display
ERROR–xx ERR–xx E–xx
(2) Error Code List
Code Class Displayed error code Description of the code and potential cause(s)
10 Electricity Carriage Home NG CRG can't be moved to inner diameter.
SERVO LSI Com- CRG can't be moved from inner diameter.
munication Error → Failure on home switch or CRG move mechanism.
Communication error between microcomputer and SERVO LSI.
11 Electricity Focus Servo NG Focusing not available.
→ Stains on rear side of disc or excessive vibrations on REWRITABLE.
12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).
Subcode NG → Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Turned over disc are found, though rarely.
CD signal error.
17 Electricity Setup NG AGC protection doesn't work. Focus can be easily lost.
→ Damages or stains on disc, or excessive vibrations on REWRITABLE.
30 Electricity Search Time Out Failed to reach target address.
→ CRG tracking error or damages on disc.
44 Electricity ALL Skip Skip setting for all track.
(CD-R/RW)
50 Mechanism CD On Mech Error Mechanical error during CD ON.
→ Defective loading motor, mechanical lock and mechanical sensor.
A0 System Power Supply NG Power (VD) is ground faulted.
→ Failure on SW transistor or power supply (failure on connector).
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.
DEH-2800MP/XN/UC521 2 3 4
C
D
F
A
B
E
5 6 7 8
6.4 SYSTEM MICROCOMPUTER TEST PROGRAM
- PCL OutputIn the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode cancelled), shift the TESTIN IC601(Pin 15) terminal to H. The clock signal is output from the PCL terminal IC601(Pin 14). The frequency of the clock signal is 786.432 kHz that is one 16th of the fundamental frequency. The clock signal should be 786.432 kHz ± 31.5 Hz. If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.
DEH-2800MP/XN/UC 535 6 7 8
C
D
F
A
B
E
1 2 3 4
7. GENERAL INFORMATION7.1 DIAGNOSIS7.1.1 DISASSEMBLY
- Removing the CD Mechanism Module (Fig.1)
1
Fig.1
- Removing the Case (not shown)
Grille Assy
- Removing the Grille Assy (Fig.1)
1. Remove the Case.
CD Mechanism Module
1
1
1
1
Fig.2Tuner Amp Unit
- Removing the Tuner Amp Unit (Fig.2)
Remove the screw.1
Remove the four screws.
Disconnect the connector and then remove theCD Mechanism Module.
2 Release the two latchs and then remove the Grille Assy.
2 2
1
22
2
3 33
Remove the three screws.2
Straighten the tabs at three locations indicated and then remove the Tuner Amp Unit.
3
DEH-2800MP/XN/UC541 2 3 4
C
D
F
A
B
E
5 6 7 8
A
A
B
B
Upper Frame
Lower Frame
B
B
B
B
a
Damper
Carriage Mechanism
Damper
Do not squeeze this area.
- How to hold the Mechanism Unit
- Removing the Upper and Lower Frames1. With a disc inserted and clamped in the
mechanism, remove the two Springs (A), the six Springs (B), and the four Screws.
2. Turn the Upper Frame using the part "a" as a pivot, and remove the Upper Frame.
3. While lifting the Carriage Mechanism, remove it from the three Dampers.
Caution: When assembling, be sure to apply some alcohol to the Dampers and assemble the mechanism in a clamped state.
1. Hold the Upper and Lower Frames.2. Do not hold the front portion of the Upper
Frame, because it is not very solid.
DEH-2800MP/XN/UC 555 6 7 8
C
D
F
A
B
E
1 2 3 4
Screw
Shorting Solder
CD Core Unit
Solder
Chassis
Pickup Rack
Pickup
Poly Washer Change Arm
Pickup Lock Arm
Feed Screw
Planet Gear
Inner Holder
- How to remove the CD Core Unit1. Apply Shorting Solder to the flexible cable of
the Pickup, and disconnect it from the connector.
2. Unsolder the four leads, and loosen the Screw.
3. Remove the CD Core Unit.Caution: When assembling the CD Core Unit,
assemble it with the SW in a clamped state so as not to damage it.
- How to remove the Pickup Unit1. Make the system in the carriage mechanism mode, and have it clamped.2. Remove the CD Core Unit and remove the leads from the Inner Holder.3. Remove the Poly Washer, Change Arm, and Pickup Lock Arm.4. While releasing from the hook of the Inner Holder, lift the end of the Feed Screw.Caution: When assembling, move the Planet Gear to the load/eject position before setting the Feed Screw in the Inner
Holder.Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load Carriage Motor Assy, do not make them loose over the Feed Screw.
DEH-2800MP/XN/UC561 2 3 4
C
D
F
A
B
E
5 6 7 8
7.1.2 CONNECTOR FUNCTION DESCRIPTION
Pin No.12345678
B.UPGNDACCNCNCB.REMOTENCNC
Pin No.9
10111213141516
RL-FL-RL+FL+RR-FR-RR+FR+
16 2115
1413
1211
109
87
65
43
REAR OUTPUTANTENNA JACK
DEH-2800MP/XN/UC 575 6 7 8
C
D
F
A
B
E
1 2 3 4
7.2 PARTS7.2.1 IC
- Pin Functions (PE5518A)Pin No. Pin Name I/O Function and Operation
12,3
45,6
789
10111213141516171819202122
23-31323334353637383940
41,4243
44-4647484950515253545556575859606162636465666768
MODEL1NCAVSSNCAREF1KYDTDPDTNCTUNPDITUNPDOTUNPCKPCLTESTINBSIBDATABSCKDORAONNCswvddILMPWNCDALMONVSSBRSTBRXENCDRESETROMDATAROMCLKROMCSRECEIVENCSYSPWNCSTRKEY2MUTEANTPWNCVSTVDTVCKNCTUNPCE2TUNPCERDTRDSLKRDS57KRESETLDETRCKasensbsensdsenssourceVSSVDD
I
IO
IOOOIIOO
OO
O
OI/OOOOOO
O
IOO
OOO
OOIII
IIIIII
Model select inputNot usedGNDNot usedVDDDisplay microcomputer data inputDisplay microcomputer communication data outputNot usedPLL data inputPLL data outputPLL clock outputClock adjustment outputTest program inputBus serial data inputBus serial output dataBus serial clock outputNot usedNot usedDisplay microcomputer chip select outputIllumination power outputNot usedOutput for dark current reduction circuit / Stand-by mode : L outputGNDBus reset outputBus RX enable input/outputCD microcomputer reset signal outputROM collection data outputROM collection clock outputROM collection chip select outputRDS decoder receiving outputNot usedSystem power outputNot usedWired remote control input 2System mute outputAuto antenna control outputNot usedE.VOL strobe outputE.VOL data outputE.VOL clock outputNot usedPLL chip enable output 2PLL chip enable outputRDS LK inputRDS clock inputRDS 57K inputResetPLL lock detection inputRDS clock inputACC sense inputBack up sense inputGrille detach sense inputSource sense inputGNDVDD
DEH-2800MP/XN/UC581 2 3 4
C
D
F
A
B
E
5 6 7 8
20 41
601
*PE5518A
406180
21
1
TA
B
2
P-G
ND
2
3
OU
T2
-
4
ST
BY
5
OU
T2
+
6
VC
C
7
OU
T1
-
8
P-G
ND
1
9
OU
T1
+
10
SV
R
11
IN1
12
IN2
13
S-G
ND
14
IN4
15
IN3
16
AC
-GN
D
17
OU
T3
+
18
P-G
ND
3
19
OU
T3
-
20
VC
C
21
OU
T4
+
22
MU
TE
23
OU
T4
-
24
P-G
ND
4
SW
ITC
H
25
+ - +-
Off
set
De
tect
ion
+ - +-
Off
set
De
tect
ion
+-+-
Off
set
De
tect
ion
+-+-
Off
set
De
tect
ion
Pro
tect
or;
Ov
er
curr
en
t li
mit
sw_vcc
stby
Pro
tect
or;
Sh
ort
cir
cuit
Mu
te c
ircu
it
amp_vcc
Sta
nd
-by
Cir
cuit
Pro
tect
or;
Ov
er
vo
lta
ge
sw_vcc
Pro
tect
or;
Th
erm
alR
efe
ren
cea
mp
_vcc
PAL007B
69,70717273747576
77,787980
X2,1IC(VPP)NCVSSAVDDAVREF1SLNCBSRQSTRKEY1
I
II
Crystal oscillator connection pin GND Not used VSS VDD VDD Signal level input Not used Bus slave service requestWired remote control input 1
Pin No. Pin Name I/O Function and Operation
IC's marked by * are MOS type.
Be careful in handling them because they are very
liable to be damaged by electrostatic induction.
DEH-2800MP/XN/UC 595 6 7 8
C
D
F
A
B
E
1 2 3 4
- Pin Layout
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
IN1_L
IN2_L
IN3_L
IN4+_L
IN4-_L
Front_L
Rear_L
Vcc
Vref
GND
IN1_R
IN2_R
IN3_R
IN4+_R
IN4-_R
Front_R
Rear_R
STB
CLK
DATA
- Block Diagram
Isol
ator
Isol
ator
Aut
o
Zer
o
Gai
n
Adj
uste
r
Input Selector
TR
EB
AS
SLO
UD
NE
SS
Sec
onda
ry
Vol
ume
Fro
nt_R
Rea
r_R
Fro
nt_L
Rea
r_L
Ant
i-Rad
iatio
nF
ilter
Ant
i-Alia
sF
ilter
Prim
ary
Vol
ume
Dig
ital
Blo
ck
IN1_
L
IN2_
L
IN3_
L
IN4+
_L
IN4-
_L
IN4-
_R
IN4+
_R
IN3_
R
IN2_
R
IN1_
R
STB
DATA
CLK
GND
Vcc
Vref
MID
Sec
onda
ry
Vol
umeSup
ply
&R
efer
ence
Sec
onda
ry
Vol
ume
Sec
onda
ry
Vol
ume
PML014A
DEH-2800MP/XN/UC601 2 3 4
C
D
F
A
B
E
5 6 7 8
NJM2885DL1-33
IN
1
GND
2
OUT
3
BandgapReference
ThermalProtection
+-
- Pin Functions(PD6340A)Pin No. Pin Name I/O Function and Operation
1-5 SEG4-0 O LCD segment output6-9 COM3-0 O LCD common output 10 VLCD LCD drive power supply
11-14 KST3-0 O Key strobe output15,16 KDT0,1 I Key data input (analogue input)
17 REW I Remote control reception input18 DPDT I Display data input19 NC Not used20 KYDT O Key data output21 MODA GND22 X0 Crystal oscillator connection pin23 X1 Crystal oscillator connection pin24 VSS GND
25,26 KDT2,3 I Key data input27 NC Not used28 KST4 O Key strobe output
29-32 NC Not used33-55 SEG35-13 O LCD segment output
56 VDD Power supply57-64 SEG12-5 O LCD segment output
* PD6340A
49
48 33
32
17
161
64
DEH-2800MP/XN/UC 615 6 7 8
C
D
F
A
B
E
1 2 3 4
- Pin Functions (UPD63763CGJ)Pin No. Pin Name I/O Function and Operation
123
4-89-16
171819202122
23,242526272829303132333435363738
39-4142434445464748495051525354555657585960616263646566676869
D.VDDD1.GNDresetAB12-8AD7-0csASTBreadwritewaitINTQIFMODE0,1D1.VDDDA.VDDROUTDA.GNDREGCDA.GNDLOUTDA.VDDX.VDDXTALxtalX.GNDVDDREG15PWMSW0TEST3-1PWMSW1TESTEND1.GNDDINDOUTSCKINSCKOLRCKINLRCKxtalenD1.VDDRFCK/HOLDWFCK/MIRRPLCK/RFOKLOCK/RFOKC1D1/C8M/(RA13)C1D2/C16M/(RA12)C2D1/RMUTEC2D2/LMUTEC2D3/SHOCKD1.GNDC33M(rcs)RA11(CKE)rascas)(LDQM)cas!(UDQM)
II
I/OIIIIOOI
O
O
IO
IIII
IOIOIOI
OOOOOOOOO
OOOOOOO
Power supply for digital circuitsGround for 1.6 V digital circuitsInput of resetAddress bus 12-8 from the microcomputerAddress/data bus 7-0 to the microcomputerChip selectionAddress strobeControl signals(read)Control signals(write)Control signals(wait)Interruption signals to the external microcomputerSwitching the microcomputer I/F 0, 1Power supply for 1.6 V digital circuitsPower supply for DACOutput of audio for the right channel Ground for DACConnected to the capacitor for band gapGround for DACOutput of audio for the left channel Power supply for DACPower supply for the crystal oscillatorConnected to the crystal oscillator(16.9344 MHz)Connected to the crystal oscillator(16.9344 MHz)Ground for the crystal oscillatorControl of 1.6 V regulatorSetup 0 for PWM output(SD, MD)Connected to GroundSetup 1 for PWM output(FD, TD)Connected to GroundGround for 1.6 V digital circuitsInput of audio dataOutput of audio dataClock input for audio dataClock output for audio dataInput of LRCK for audio dataOutput LRCK for audio dataPermission to oscillate 16.9344 MHzPower supply for 1.6 V digital circuitsOutput of RFCK/HOLD signalOutput of WFCK/MIRR signalOutput of PLCK/Output of RFOKOutput of LRCK/Output of RFOKInformation on error correction/C8M : 8 MHzInformation on error correction/C16M : 16 MHzInformation on error correction/Mute for RchInformation on error correction/Mute for LchInformation on error correction/Detection of vibrationGround for 1.6 V digital circuitsOutput of 33.8688 MHz(CLK for SDRAM)DRAM csOutput of DRAM address 11Output of DRAM CKEOutput of DRAM rasOutput of DRAM lower cas(LDQM)Output of DRAM upper cas(UDQM)
DEH-2800MP/XN/UC621 2 3 4
C
D
F
A
B
E
5 6 7 8
36 73
1081
* UPD63763CGJ
7210
9
144
37
Pin No. Pin Name I/O Function and Operation707172
73-8889-99
100101102103104105106107108109110111112113114115116117118119
120,121122123124125126127128129130131132133134135136137138139140141142143144
weoe(cas)D.GNDRDB0-15RA0-10D.VDDFD+FD-TD+TD-SD+SD-MD+MD-REFOUTSVAD.VDDEFMASYATESTRFIAD.GNDAGCOC3TAGCIRFOEQ2,1RF2-RF-A.GNDACBDFEVREFINA.VDDREFOUTREFCFE-FEOADINTE-TEOTE2TECLDPDD.GND
OO
I/OO
OOOOOOOOO
OIOI
OOIOIII
IIIIIII
OIIOIIOOIOI
Output of DRAM weOutput of DRAM oe(cas)Ground for digital circuitsInput/output of DRAM data0-15Output of DRAM address0-10Power supply for digital circuitsOutput of focus drive PWM +Output of focus drive PWM -Output of tracking drive PWM +Output of tracking drive PWM -Output of thread drive PWM +Output of thread drive PWM -Output of spindle drive PWM +Output of spindle drive PWM -REFOUT for servoPower supply for ADCOutput of EFM signalsInput of asymmetryAnalog testsInput of RFGround for the analog systemOutput of RFConnection to the capacitor for detecting 3TInput of AGCOutput of RF(AGC)Equalizer 2, 1Reversal input of RF2Reversal input of RFGround for the analog systemInput of AInput of CInput of BInput of DInput of FInput of EInput of reference voltagePower supply for the analog systemOutput of reference voltageConnected to the capacitor for output of REFOUTReversal input of FEOutput of FEInput of FE, TE A/D converterReversal input of TEOutput of TETE2TECOutput of LDInput of PDGround for digital circuits
DEH-2800MP/XN/UC 635 6 7 8
C
D
F
A
B
E
1 2 3 4
- Pin Functions (PE5505A)Pin No. Pin Name I/O Format Function and Operation
123456789
10111213141516171819202122232425262728293031323334
35,363738394041424344454647484950515253545556
AVREFAVSStestinCLAMPEVDDFMODEFLRQIC/FLMD0VDDREGCVSSX1X2resetXT1XT2PULLDOWNejswxintNCbrstBSIBSObsckFTxDFRxDBRXENbsrqdspokDSCSNS8EJ(S905)12EJ(S904)EVSSEVDDSRAMLEVEL0,1EMPHemphCDMUTELOEJCLCONTHOMEadenaLRCKOKSRAMLEVEL2CD3VON(MCKRQ)CONTxrstVDCONTxsixsoxckxwaitXASTBAD0INT
I
I
II
I
I
IIOI/OOI
I/OI/O
III
OO
OIOOOOOOOIOOIOO
C
C/CC
/C/C
CCC
C
CCCCCCC
CCCCC
A power supply / Positive power supply(5V)A power supply GND Chip check test program starting inputNot usedE power supply / Positive power supplyFor flash rewriting / L : flash rewriting modeFor flash rewriting / Reset voltage controlIC : VSS direct connection/FLMOD0 : Pull-down Positive power supply(5V) Connected to the capacity stabilizing output of the regulatorGND Oscillator connection for mainclock Oscillator connection for mainclockSystem reset inputConnected to the oscillator for subclock(connected to VSS via the resistor)Connected to the oscillator for subclock(Open) Connected to EVDD or EVSS via the resistorNot usedCD LSI interruption signal inputNot usedBus reset inputBus serial data inputBus serial data outputBus serial clock input/outputFor flash rewriting(transmitted signal) For flash rewriting(received signal) Bus RX enable input/outputBus serial clock input/outputNot usedDisc state sense inputinput of detection of 8 cm disc ejectioninput of detection of 12 cm disc ejectionE power supply GNDE power supply / Positive power supplySRAM level meter outputEmphasis information outputNot used Not used Not used Driver input switching outputHome SW sense inputA/D reference voltage supply control output(DOUT mute output)SRAM level meter outputCD + 3.3 V power supply control output(Digital output : MCKRQ)Servo driver power supply control outputCD LSI reset control outputVD power supply control outputCD LSI serial data inputCD LSI serial data outputCD LSI serial clock outputCD LSI wait control signal inputCD LSI address strobe outputAddress/data Bus 0Not used
DEH-2800MP/XN/UC641 2 3 4
C
D
F
A
B
E
5 6 7 8
25 51
751
* PE5505A
507610
026
NJM2886DL3-33
CONTROL
1
VIN
2
GND
3
VO
4
NC
5
BandgapReference
ThermalProtection
+-
Format meaning C C MOS
Pin No. Pin Name I/O Format Function and Operation575859
60,616263
64-686970
71-7576
77-9091-93
9495
96,979899
100
ROMDATAROMCKROMCSNCCLKOUTLOCKNCBVSSBVDDNCFLMD1NCA/DcsensTYPE_A/DNCTEMPVDSENSDSCSNS
I/OOO
I
I/O
I
C
/C
E2PROM data input/outputE2PROM clock outputE2PROM chip selection outputNot used Not used Spindle lock inputNot used B power supply GND B power supply / Positive power supplyNot used Address/Data Bus 5Not used Not used Not used Not used Not used Not used VD power supply short sense inputNot used
DEH-2800MP/XN/UC 655 6 7 8
C
D
F
A
B
E
1 2 3 4
No. Symbol I/O Explain1 AMANT I AM antenna input AM antenna input high impedance AMANT pin is connected with
an all antenna by way of 4.7µH. (LAU type inductor) A series circuit including an inductor and a resistor is connected with RF ground for the countermeasure against the hum of power transmission line.
2 RFGND RF ground Ground of antenna block3 FMANT I FM antenna input Input of FM antenna 75Ω Surge absorber(DSP-201M-S00B) is necessary.4 VCC power supply The power supply for analog block. D.C 8.4V ± 0.3V5 SL O signal level Output of FM/AM signals level6 CE2 I chip enable-2 Chip enable for EEPROM ”Low” active7 NC non connection Not used8 CE1 I chip enable-1 Chip enable for AF•RF ”High” active9 CK I clock Clock
10 DI I data in Data input11 NC non connection Not used12 OSCGND osc ground Ground of oscillator block13 ROM_VDD power supply Power supply for EEPROM pin 13 is connected with a power supply of
micro computer.14 DO O data out Data output15 DGND digital ground Ground of digital block16 NC non connection Not used17 VDD_3.3 power supply The power supply for digital block. 3.3V ± 0.2V18 NC non connection Not used19 NC non connection Not used20 NC non connection Not used21 NC non connection Not used22 AUDIOGND audio ground Ground of audio block23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output 24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output
FMRF
ANT adjRF adj
FM ANT
T51 CF52
RFG
ND
OS
CG
ND
DG
ND
AU
DIO
GN
D
NC
VC
C
VD
D_3
.3
3.3V 2.5VIC 4
3.3V 2.5V
←
IC 22.5V
NC
CE
2
RO
M_V
DD SL DI
CK
CE
1
NC
DO
NC
NC
NC
NC
7 6 13 5 10 9 8 11 14 18 19 20 21
1
3
2 12 15 22 16 4 17
IC 13.3V
AM ANT FMRFATT
LPFOSC
IC 3 EEPROM5.0V
IC 55V 3.3V←
ATT
MIXER, IF AMP DET, FM MPX
24
23
Rch
Lch
- FM/AM Tuner Unit
DEH-2800MP/XN/UC661 2 3 4
C
D
F
A
B
E
5 6 7 8
7.2.2 DISPLAY
- LCD(CAW1906)(DEH-2800MP/XN/UC)- LCD(CAW1905)(DEH-2850MP/XN/ES)
SE
GM
EN
T
CO
MM
ON
COM 3
COM 2
COM 1
COM 0
SEG38
SEG37
SEG36
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG 9
SEG 8
SEG 7
SEG 6
SEG 5
SEG 4
SEG 3
SEG 2
SEG 1
SEG 0
SEG39
COM 3
COM 2
COM 1
COM 0
DEH-2800MP/XN/UC 675 6 7 8
C
D
F
A
B
E
1 2 3 4
7.3 OPERATIONAL FLOW CHART
AREF1, VDD, AVDD, AVREF1=5 VPin 7, 68, 74, 75
Power ON
bsens=L
asens=L
bsensPin 64
asensPin 63
swvdd←LPin 21
Source keys operative
Completes power-on operation.(After that, proceed to each source operation.)
SYSPW←HPin 43
Starts communication with Grille microcomputer.
Source ON
300 ms
300 ms
In case of the above signal, the communication with Grille microcomputer may fail.If the time interval is not 300 msec, the oscillator may be defective.
DEH-2800MP/XN/UC681 2 3 4
C
D
F
A
B
E
5 6 7 8
8. OPERATIONS
DEH-2800MP/XN/UC 695 6 7 8
C
D
F
A
B
E
1 2 3 4
About the fixing screws for the front panelIf you do not operate the Detaching and Replacingthe Front Panel Function, use the supplied fixingscrews and fix the front panel to this unit.
Fixing screw(CBA1994)(DEH-2800MP/XN/UC)(CXX1982)(DEH-2850MP/XN/ES)
Fixing screw(CBA1994)(DEH-2800MP/XN/UC)(CXX1982)(DEH-2850MP/XN/ES)
DEH-2800MP/XN/UC701 2 3 4
C
D
F
A
B
E
5 6 7 8
DEH-2800MP/XN/UC 715 6 7 8
C
D
F
A
B
E
1 2 3 4
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
Portions to be cleaned Cleaning toolsg
CD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008g p p
- Jigs List
Test DiscL.P.F.
TCD-782 Checking the gratingg g gChecking the grating g g g (Two pieces)( )
Name Jig No. Remarks
- Grease List
GreaseGrease
GEM1024GEM1045
CD Mechanism ModuleCD Mechanism Module
Name Grease No. Remarks
DEH-2800MP/XN/UC721 2 3 4