SUPER FLEX™POLYURETHANE SYNCHRONOUS BELTS

PITCH SPECIFICATIONSSUPER FLEX™ BELTS

2

T5 | Pitch: 5 mm 3

T10 | Pitch: 10 mm 4 T10-HF | Pitch: 10 mm 5

T20 | Pitch: 20 mm 6

T20-HF | Pitch: 20 mm 7

T20-NIRO | Pitch: 20 mm 8

AT5 | Pitch: 5 mm 9 AT10 | Pitch: 10 mm 10

AT10-HF | Pitch: 10 mm 11

AT10-NIRO | Pitch: 10 mm 12

ATL10 | Pitch: 10 mm 13

ATL10-HF | Pitch: 10 mm 14

AT20 | Pitch: 20 mm 15

AT20-HF | Pitch: 20 mm 16

ATL20 | Pitch: 20 mm 17 ATL20-NIRO | Pitch: 20 mm 18

HTD®5 | Pitch: 5 mm 19

HTD®L5 | Pitch: 5 mm 20

HTD®8 | Pitch: 8 mm 21

HTD®8-HF | Pitch: 8 mm 22 HTD®8-NIRO | Pitch: 8 mm 23

HTD®14 | Pitch: 14 mm 24

HTD®14-HF | Pitch: 14 mm 25

H | Pitch: 12.7 mm 26

H-HF | Pitch: 12.7 mm 27

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

TABLE OF CONTENT

1.22.2

5

3Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Standard Width (mm) 10 16 25 32 50 75 100

Tensile Strength (Average Value) FBreak (N)

Steel 1,250 2,000 3,375 4,250 6,875 10,375 13,875

Allowable Belt Force F1all (N)

Steel 311 498 840 1,058 1,711 2,582 3,453

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 356 570 890 1,139 1,780 2,670 3,560

Specific Belt Mass msp (kg/m/mm)

Steel 0.0022

Specific Belt Stiffness csp (N)

Steel 77,778 124,444 210,000 264,444 427,778 645,556 863,333

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

10

Minimum Pulley Diameter 15.91 mm

Minimum Back Bend Diameter 30 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

T5 | Pitch: 5 mm

10

2.54.5

4Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

14

Minimum Pulley Diameter 44.56 mm

Minimum Back Bend Diameter 80 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 16 25 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 4,200 7,140 9,240 14,700 22,260 29,820 44,940

Allowable Belt Force F1all (N)

Steel 1,123 1,909 2,470 3,929 5,950 7,971 12,012

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 1,082 1,690 2,163 3,380 5,070 6,760 10,140

Specific Belt Mass msp (kg/m/mm)

Steel 0.0044

Specific Belt Stiffness csp (N)

Steel 280,662 477,125 617,456 982,316 1,487,507 1,992,699 3,003,081

T10 | Pitch: 10 mm

10

2.54.5

5Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

T10-HF | Pitch: 10 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

12

Minimum Pulley Diameter 38.2 mm

Minimum Back Bend Diameter 60 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 16 25 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 6,200 10,540 13,640 21,700 32,860 44,020 66,340

Allowable Belt Force F1all (N)

Steel 1,376 2,340 3,028 4,818 7,295 9,773 14,728

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 1,082 1,690 2,163 3,380 5,070 6,760 10,140

Specific Belt Mass msp (kg/m/mm)

Steel 0.0047

Specific Belt Stiffness csp (N)

Steel 344,118 585,000 757,059 1,204,412 1,823,824 2,443,235 3,682,059

20

85

6Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

T20 | Pitch: 20 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

15

Minimum Pulley Diameter 95.49 mm

Minimum Back Bend Diameter 120 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,760 mm

Standard Width (mm) 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 18,050 29,450 44,650 59,850 90,250

Allowable Belt Force F1all (N)

Steel 4,739 7,731 11,722 15,712 23,693

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 4,045 6,320 9,480 12,640 18,960

Specific Belt Mass msp (kg/m/mm)

Steel 0.0075

Specific Belt Stiffness csp (N)

Steel 1,184,650 1,932,850 2,930,450 3,928,050 5,923,250

20

85

7Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

T20-HF | Pitch: 20 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

12

Minimum Pulley Diameter 76.39 mm

Minimum Back Bend Diameter 100 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,760 mm

Standard Width (mm) 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 16,435 26,815 40,655 54,495 82,175

Allowable Belt Force F1all (N)

Steel 4,378 7,142 10,829 14,515 21,888

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 4,045 6,320 9,480 12,640 18,960

Specific Belt Mass msp (kg/m/mm)

Steel 0.0072

Specific Belt Stiffness csp (N)

Steel 1,094,400 1,785,600 2,707,200 3,628,800 5,472,000

20

85

8Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

20

Minimum Pulley Diameter 127.32 mm

Minimum Back Bend Diameter 160 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,760 mm

Standard Width (mm) 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 13,538 22,088 33,488 44,888 67,688

Allowable Belt Force F1all (N)

Steel 3,554 5,799 8,791 11,784 17,770

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 4,045 6,320 9,480 12,640 18,960

Specific Belt Mass msp (kg/m/mm)

Steel 0.0074

Specific Belt Stiffness csp (N)

Steel 888,488 1,449,638 2,197,838 2,946,038 4,442,438

T20-NIRO | Pitch: 20 mm

2.71.25

9Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

15

Minimum Pulley Diameter 23.87 mm

Minimum Back Bend Diameter 60 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 10 16 25 32 50 75 100

Tensile Strength (Average Value) FBreak (N)

Steel 2,565 4,275 7,125 9,120 14,535 21,945 29,355

Allowable Belt Force F1all (N)

Steel 634 1,056 1,761 2,253 3,591 5,422 7,253

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 516 826 1,290 1,651 2,580 3,870 5,160

Specific Belt Mass msp (kg/m/mm)

Steel 0.0033

Specific Belt Stiffness csp (N)

Steel 158,445 264,075 440,125 563,360 897,855 1,355,585 1,813,315

AT5 | Pitch: 5 mm

10

2.5 4.5

10Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

15

Minimum Pulley Diameter 47.75 mm

Minimum Back Bend Diameter 120 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 25 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 14,250 18,050 29,450 44,650 59,850 90,250

Allowable Belt Force F1all (N)

Steel 3,741 4,739 7,731 11,722 15,712 23,693

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 2,580 3,302 5,160 7,740 10,320 15,480

Specific Belt Mass msp (kg/m/mm)

Steel 0.0057

Specific Belt Stiffness csp (N)

Steel 935,250 1,184,650 1,932,850 2,930,450 3,928,050 5,923,250

AT10 | Pitch: 10 mm

10

2.5 4.5

11Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

AT10-HF | Pitch: 10 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

12

Minimum Pulley Diameter 38.20 mm

Minimum Back Bend Diameter 100 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 25 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 12,975 16,435 26,815 40,655 54,495 82,175

Allowable Belt Force F1all (N)

Steel 3,456 4,378 7,142 10,829 14,515 21,888

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 2,580 3,302 5,160 7,740 10,320 15,480

Specific Belt Mass msp (kg/m/mm)

Steel 0.0055

Specific Belt Stiffness csp (N)

Steel 864,000 1,094,400 1,785,600 2,707,200 3,628,800 5,472,000

10

2.5 4.5

12Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

20

Minimum Pulley Diameter 63.66 mm

Minimum Back Bend Diameter 160 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 25 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 10,688 13,538 22,088 33,488 44,888 67,668

Allowable Belt Force F1all (N)

Steel 2,806 3,554 5,799 8,791 11,784 17,770

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 2,580 3,302 5,160 7,740 10,320 15,480

Specific Belt Mass msp (kg/m/mm)

Steel 0.0057

Specific Belt Stiffness csp (N)

Steel 701,438 888,488 1,449,638 2,197,838 2,946,038 4,442,438

AT10-NIRO | Pitch: 10 mm

10

2.54.8

13Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

25

Minimum Pulley Diameter 79.58 mm

Minimum Back Bend Diameter 150 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 25 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 20,760 25,950 43,250 65,740 88,230 133,210

Allowable Belt Force F1all (N)

Steel 5,079 6,348 10,581 16,082 21,584 32,588

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 2,580 3,302 5,160 7,740 10,320 15,480

Specific Belt Mass msp (kg/m/mm)

Steel 0.0067

Specific Belt Stiffness csp (N)

Steel 1,269,666 1,587,083 2,645,138 4,020,609 5,396,081 8,147,024

ATL10 | Pitch: 10 mm

10

2.54.8

14Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

20

Minimum Pulley Diameter 63.66 mm

Minimum Back Bend Diameter 130 mm

Standard Lengths 1,520–12,000 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 25 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 23,100 28,875 48,125 73,150 98,175 148,225

Allowable Belt Force F1all (N)

Steel 4,402 5,502 9,170 13,939 18,708 28,245

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 2,580 3,302 5,160 7,740 10,320 15,480

Specific Belt Mass msp (kg/m/mm)

Steel 0.0072

Specific Belt Stiffness csp (N)

Steel 1,100,450 1,375,563 2,292,604 3,484,758 4,676,913 7,061,221

ATL10-HF | Pitch: 10 mm

20

58

15Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

AT20 | Pitch: 20 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

18

Minimum Pulley Diameter 114.59 mm

Minimum Back Bend Diameter 180 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,760 mm

Standard Width (mm) 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 25,950 43,250 65,740 88,230 133,210

Allowable Belt Force F1all (N)

Steel 6,530 10,883 16,542 22,201 33,519

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 6,950 10,860 16,290 21,720 32,580

Specific Belt Mass msp (kg/m/mm)

Steel 0.0097

Specific Belt Stiffness csp (N)

Steel 1,632,428 2,720,713 4,135,484 5,550,255 8,379,797

20

58

16Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

AT20-HF | Pitch: 20 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

18

Minimum Pulley Diameter 114.59 mm

Minimum Back Bend Diameter 150 mm

Standard Lengths 1,520–12,000 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,760 mm

Standard Width (mm) 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 28,875 48,125 73,150 98,175 148,225

Allowable Belt Force F1all (N)

Steel 5,659 9,432 14,337 19,242 29,052

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 6,950 10,860 16,290 21,720 32,580

Specific Belt Mass msp (kg/m/mm)

Steel 0.0101

Specific Belt Stiffness csp (N)

Steel 1,414,864 2,358,107 3,584,322 4,810,538 7,262,969

20

58

17Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

ATL20 | Pitch: 20 mm

Standard Width (mm) 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 32,000 54,400 83,200 112,000 172,800

Allowable Belt Force F1all (N)

Steel 7,918 13,461 20,587 27,714 42,758

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 6,950 10,860 16,290 21,720 32,580

Specific Belt Mass msp (kg/m/mm)

Steel 0.0108

Specific Belt Stiffness csp (N)

Steel 1,979,545 3,365,227 5,146,817 6,928,408 10,689,543

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

25

Minimum Pulley Diameter 159.15 mm

Minimum Back Bend Diameter 250 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,760 mm

20

58

18Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

ATL20-NIRO | Pitch: 20 mm

Standard Width (mm) 32 50 75 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 22,500 38,250 58,500 78,750 121,500

Allowable Belt Force F1all (N)

Steel 6,110 10,388 15,887 21,386 32,996

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 6,950 10,860 16,290 21,720 32,580

Specific Belt Mass msp (kg/m/mm)

Steel 0.0106

Specific Belt Stiffness csp (N)

Steel 1,527,600 2,596,920 3,971,760 5,346,600 8,249,040

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

26

Minimum Pulley Diameter 165.52 mm

Minimum Back Bend Diameter 260 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,760 mm

5

2.1 3.6

19Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Standard Width (mm) 25 50 75 100

Tensile Strength (Average Value) FBreak (N)

Steel 7,410 14,700 22,260 29,820

Allowable Belt Force F1all (N)

Steel 1,909 3,929 5,950 7,971

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 1,020 2,040 3,060 4,080

Specific Belt Mass msp (kg/m/mm)

Steel 0.0044

Specific Belt Stiffness csp (N)

Steel 477,135 982,316 1,487,507 1,992,699

Specifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

16

Minimum Pulley Diameter 25.46 mm

Minimum Back Bend Diameter 80 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

HTD®5 | Pitch: 5 mm

5

2.1 3.6

20Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

HTD®L5 | Pitch: 5 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

14

Minimum Pulley Diameter 22.28 mm

Minimum Back Bend Diameter 60 mm

Standard Lengths 1,520–12,000 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 25 50 75 100

Tensile Strength (Average Value) FBreak (N)

Steel 10,540 21,700 32,860 44,020

Allowable Belt Force F1all (N)

Steel 2,340 4,818 7,295 9,773

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 1,020 2,040 3,060 4,080

Specific Belt Mass msp (kg/m/mm)

Steel 0.0049

Specific Belt Stiffness csp (N)

Steel 585,000 1,204,412 1,823,824 2,443,235

8

5.63.4

21Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

HTD®8 | Pitch: 8 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

20

Minimum Pulley Diameter 50.93 mm

Minimum Back Bend Diameter 120 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,752 mm

Standard Width (mm) 25 32 50 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 14,250 18,050 29,450 59,850 90,250

Allowable Belt Force F1all (N)

Steel 3,741 4,739 7,731 15,712 23,693

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 1,870 2,394 3,740 7,480 11,220

Specific Belt Mass msp (kg/m/mm)

Steel 0.0069

Specific Belt Stiffness csp (N)

Steel 935,250 1,184,650 1,932,850 3,928,050 5,923,250

8

5.63.4

22Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

HTD®8-HF | Pitch: 8 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

16

Minimum Pulley Diameter 40.74 mm

Minimum Back Bend Diameter 100 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,752 mm

Standard Width (mm) 25 32 50 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 12,975 16,435 26,815 54,495 82,175

Allowable Belt Force F1all (N)

Steel 3,456 4,378 7,142 14,515 21,888

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 1,870 2,394 3,740 7,480 11,220

Specific Belt Mass msp (kg/m/mm)

Steel 0.0066

Specific Belt Stiffness csp (N)

Steel 864,000 1,094,400 1,785,600 3,628,800 5,472,000

8

5.63.4

23Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

HTD®8-NIRO | Pitch: 8 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

25

Minimum Pulley Diameter 63.66 mm

Minimum Back Bend Diameter 150 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,752 mm

Standard Width (mm) 25 32 50 100 150

Tensile Strength (Average Value) FBreak (N)

Steel 10,688 13,538 22,088 44,888 67,688

Allowable Belt Force F1all (N)

Steel 2,806 3,554 5,799 11,784 17,770

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 1,870 2,394 3,740 7,480 11,220

Specific Belt Mass msp (kg/m/mm)

Steel 0.0068

Specific Belt Stiffness csp (N)

Steel 701,438 888,488 1,449,638 2,946,038 4,442,438

14

6 10

24Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

HTD®14 | Pitch: 14 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

28

Minimum Pulley Diameter 124.78 mm

Minimum Back Bend Diameter 200 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 100 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 25 40 55 85 115 170

Tensile Strength (Average Value) FBreak (N)

Steel 20,760 32,870 46,710 74,390 100,340 150,510

Allowable Belt Force F1all (N)

Steel 5,156 8,164 11,601 18,476 24,921 37,381

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 3,430 5,488 7,546 11,662 15,778 23,324

Specific Belt Mass msp (kg/m/mm)

Steel 0.0108

Specific Belt Stiffness csp (N)

Steel 1,289,000 2,040,917 2,900,250 4,618,917 6,230,167 9,345,250

14

6 10

25Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

HTD®14-HF | Pitch: 14 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

23

Minimum Pulley Diameter 102.50 mm

Minimum Back Bend Diameter 160 mm

Standard Lengths 1,520–12,000 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,750 mm

Standard Width (mm) 25 40 55 85 115 170

Tensile Strength (Average Value) FBreak (N)

Steel 23,100 36,575 51,975 82,775 111,650 167,475

Allowable Belt Force F1all (N)

Steel 4,470 7,077 10,056 16,016 21,603 32,404

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 3,430 5,488 7,546 11,662 15,778 23,324

Specific Belt Mass msp (kg/m/mm)

Steel 0.0111

Specific Belt Stiffness csp (N)

Steel 1,117,380 1,769,185 2,514,105 4,003,945 5,400,670 8,101,005

12.7 mm.500"

4.06 mm.160"

2.29 mm.090"

26Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Standard Width (mm) 12.7 19.05 25.4 38.1 50.8 76.2 101.6 152.4

Tensile Strength (Average Value) FBreak (N)

Steel 3,360 5,040 7,140 10,920 14,700 22,260 29,820 44,940

Allowable Belt Force F1all (N)

Steel 898 1,347 1,909 2,919 3,929 5,950 7,971 12,012

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 980 1,470 1,960 2,940 3,920 5,880 7,840 11,760

Specific Belt Mass msp (kg/m/mm)

Steel 0.0040

Specific Belt Stiffness csp (N)

Steel 224,529 336,794 477,125 729,721 982,316 1,487,507 1,992,699 3,003,081

H | Pitch: 12.7 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

14

Minimum Pulley Diameter 56.60 mm

Minimum Back Bend Diameter 79.4 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 101.6 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,752.6 mm

12.7 mm.500"

4.06 mm.160"

2.29 mm.090"

27Gatessuperflex.com The manufacturers reserve the right to amend details where necessary. © Gates Corporation

SUPER FLEX™ BELTSTRULY ENDLESS FLEX BELTS

Standard Width (mm) 12.7 19.05 25.4 38.1 50.8 76.2 101.6 152.4

Tensile Strength (Average Value) FBreak (N)

Steel 4,960 7,440 10,540 16,120 21,700 32,860 44,020 66,340

Allowable Belt Force F1all (N)

Steel 1,101 1,652 2,340 3,579 4,818 7,295 9,773 14,728

Allowable Effective Force Feall (N)

(Minimum 15 Teeth are in Mesh) 980 1,470 1,960 2,940 3,920 5,880 7,840 11,760

Specific Belt Mass msp (kg/m/mm)

Steel 0.0043

Specific Belt Stiffness csp (N)

Steel 275,294 412,941 585,000 894,706 1,204,412 1,823,824 2,443,235 3,682,059

H-HF | Pitch: 12.7 mmSpecifications

Standard Colour White

Width Tolerance up to 50 mm Width

> 50 mm Width

± 0.5 mm ± 0.75 mm

Minimum Number of Pulley Teeth zmin

12

Minimum Pulley Diameter 48.51 mm

Minimum Back Bend Diameter 60.3 mm

Standard Lengths 1,520–24,000 mm

Maximum Width for Belt Length > 12,000 mm 101.6 mm

Minimum Belt Length for Belts with Fabric on Tooth Side 1,752.6 mm

GERMANY GATES MECTROL GMBH Werner-von-Siemens-Str. 2 64319 Pfungstadt T (49) 06 157 9727 0 / F (49) 06 157 9727 272

BELGIUM GATES EUROPE BVBA Korte Keppestraat 21/51 9320 Erembodegem T (32) 53 76 28 41 / F (32) 53 76 26 09

GERMANYGATES GMBHEisenbahnweg 5052068 AachenT (49) 241 5108 226 / F (49) 241 5108 297

FRANCE GATES FRANCE S.A.R.L. B.P. 37 12, Rue de la Briqueterie Zone Industrielle, 95380 Louvres T (33) 1 34 47 41 45 / F (33) 1 34 72 20 54

ITALY GATES S.R.L. Via Senigallia 18 - Blocco A 20161 Milano MI T (39) 02 662 16 21 / F (39) 02 662 21 851

RUSSIA GATES CIS LLC Kosmodamianskaja nab. 52, building 4 Business Centre Riverside Towers, 6th floor 115054 Moscow T (7) 495 933 83 71 / F (7) 495 933 83 78

E2/20204 Gatessuperflex.comThe manufacturers reserve the right to amend details where necessary. © Gates Corporation 03/17