PITCHBACK PRO & PITCHBACK REC (Assembly Instructions) ADULT ASSEMBLY AND SUPERVISION REQUIRED. FRAME SET-UP AND ADJUSTER PLATE ASSEMBLY • See diagram for proper placement of the frame corners and side supports. • Connect the frame bends by locking them into place with the push-button pins. • Insert the side supports and lock them into position with the push-button pins. • Attach both sides of the lower frame to the “inside ” of the adjuster plate. Outer Top Hole : Place the 1” bolt through the adjuster plate using a washer between the plate and leg. Secure with a wing nut (wing nut should be facing the inside of the frame). Outer Bottom Hole : Place bolt through the plate (no washer) and ﬁnish with a wing nut. • Attach the upper frame to the “outside ” of the plate position. Top Hole : Place a 1” bolt through the upper hole on the adjuster plate using a washer between the leg and adjuster plate. Secure the bolt with a wing nut. Adjuster Knob Placement : Place bolt through remaining hole. Add a washer and adjuster knob. Secure the bolt with a wing nut. Note: Make sure all bolts are secure but DO NOT OVER TIGHTEN. NET ATTACHMENT • Position the four net corners at the front top frame and front lower frame. The 6” rear net panel faces the back of the frame. • Clip the net onto the frame with the net hooks. The net hooks must be placed uniformly around the frame for best rebounding results. REAR STORAGE AND STABILIZER PANEL • Weave the stabilizer rod through the ﬁrst row of the rear net panel. Attach the stabilizer bungee cords to the top frame. Wrap the cords around the stabilizer rod once to hold it in place and attach the other end of the cord to the lower rear frame. Tip: Move the stabilizer rod up or down to equalize the net tension. To increase net tension, continue looping the bungee cord around the rod. CHANGING PLAYING ANGLES • Loosen and remove both adjuster knobs. Pivot the top frame section into the desired playing position. Reinsert knob assembly and tighten. • Be careful to avoid pinch areas around the adjuster plate when changing playing angles. STORAGE AND/OR TRANSPORTING • Position the upright in the center position. • Remove lower bolts on both of the lower base frame angle adjuster plate. • Carefully fold the bottom frame sections up to the top frame section and replace wing nuts. WARNING : This unit does fold and has common pinch points that must be avoided when assembling, storing or changing playing angles. Check all connections and net hooks prior to each use. PARTS LIST 3 - #1 corners (plain end) 3 - #2 corners (swedged end) 6 - #3 side supports 2 – Adjuster plates 2 – Adjuster knobs 1 – Rebound net 10 – 5/16”x1” bolts 12 – Wing nuts 24 - Washers 1 – Stabilizer rod 2 – Bungee cords 38 – Net/Frame hooks (Pro Model) 32 – Net/Frame hooks (Rec Model)

PITCHBACK PRO & PITCHBACK REC (Assembly Instructions ... · PITCHBACK PRO & PITCHBACK REC (Assembly Instructions) ADULT ASSEMBLY AND SUPERVISION REQUIRED. FRAME SET-UP AND ADJUSTER

Download PDF Report

Upload
others
View
6
Download
0

Embed Size (px)

Citation preview

Page 1: PITCHBACK PRO & PITCHBACK REC (Assembly Instructions ... · PITCHBACK PRO & PITCHBACK REC (Assembly Instructions) ADULT ASSEMBLY AND SUPERVISION REQUIRED. FRAME SET-UP AND ADJUSTER

PITCHBACK PRO & PITCHBACK REC (Assembly Instructions)ADULT ASSEMBLY AND SUPERVISION REQUIRED.

FRAME SET-UP AND ADJUSTER PLATE ASSEMBLY• See diagram for proper placement of the frame corners and side supports.

• Connect the frame bends by locking them into place with the push-button pins. • Insert the side supports and lock them into position with the push-button pins. • Attach both sides of the lower frame to the “inside” of the adjuster plate.

Outer Top Hole: Place the 1” bolt through the adjuster plate using a washer between the plate and leg. Secure with a wing nut (wing nut should be facing the inside of the frame).

Outer Bottom Hole: Place bolt through the plate (no washer) and finish with a wing nut.• Attach the upper frame to the “outside” of the plate position.

Top Hole: Place a 1” bolt through the upper hole on the adjuster plate using a washer between the leg and adjuster plate. Secure the bolt with a wing nut.Adjuster Knob Placement: Place bolt through remaining hole. Add a washer and adjuster knob. Secure the bolt with a wing nut.

Note: Make sure all bolts are secure but DO NOT OVER TIGHTEN.

NET ATTACHMENT• Position the four net corners at the front top frame and front lower frame. The 6” rear net panel faces the back of the frame.• Clip the net onto the frame with the net hooks. The net hooks must be placed uniformly around the frame for best rebounding results.

REAR STORAGE AND STABILIZER PANEL• Weave the stabilizer rod through the first row of the rear net panel. Attach the stabilizer bungee cords to the top frame. Wrap the cords around the stabilizer rod once to hold it in place and attach the other end of the cord to the lower rear frame.

Tip: Move the stabilizer rod up or down to equalize the net tension. To increase net tension, continue looping the bungee cord around the rod.

CHANGING PLAYING ANGLES• Loosen and remove both adjuster knobs. Pivot the top frame section into the desired playing position. Reinsert knob assembly and tighten.• Be careful to avoid pinch areas around the adjuster plate when changing playing angles.

STORAGE AND/OR TRANSPORTING• Position the upright in the center position.• Remove lower bolts on both of the lower base frame angle adjuster plate.• Carefully fold the bottom frame sections up to the top frame section and replace wing nuts.

WARNING: This unit does fold and has common pinch points that must be avoided when assembling, storing or changing playing angles. Check all connections and net hooks prior to each use.

PARTS LIST

3 - #1 corners (plain end)3 - #2 corners (swedged end)6 - #3 side supports2 – Adjuster plates2 – Adjuster knobs1 – Rebound net10 – 5/16”x1” bolts

12 – Wing nuts24 - Washers1 – Stabilizer rod2 – Bungee cords38 – Net/Frame hooks (Pro Model)32 – Net/Frame hooks (Rec Model)