Ppt on Future

7/28/2019 Ppt on Future

1/19

A PROJECT PRESENTATION ON

FUTURISTIC VEHICLE SYSTEM

(IDEAL INSTITUT OF TECHNOLOGY

GHAZIABAD)

UNDER GUIDANCE OF:- SUBMITTED BY:-

Mr. BALWANT SINGH MANOJ KUMAR

(ASSISTANT PROFESSOR) VIVEK KUMAR

SANDEEP KR. SINGH


2/19

CONTENT1. INTRODUCTION.

2. MAIN TARGET OF PROJECT.

3. HARDWARE REQUIREMENT.

4. BLOCK DIAGRAM.

5. MICROCONTROLLER.

6. LCD.

7. RF MODULE.

8. IC 7805.

9. ADVANTAGES


3/19

INTRODUCTION

Now a days accidents are increasing at a large pace, and varioustechnologies are being introduced to reduce the accidents. In this project

we are presenting a means to prevent speed controlling with according

different zone in school zone, college zone, hospital zone, accident phone

zone, speed limit zone and silent zone etc.

The main aim of our project is to control the over speed of vehicle for

school and college zone using the robot. Here we use the RF technology for

that controlling. By this project we can control the vehicle speed through

the radio frequency. The transmitter will receive the signal in the

predetermined area only. When transmitter receives the signal,

automatically it will display as school zone and control the speed limit of

vehicle. The software for the microcontroller is written using embedded C.


4/19

MAIN TARGETS OF THE PROJECT

Control Horn (reduce noise pollution)

Parking Light Flashing (avoid accidents)

Fuel system Or Motor Control (reduce the accidents and air

pollution)


5/19

HARDWARE REQUIREMENT

Car mechanism

RF transmitter and RF receiver.

Microcontroller and power supply.


6/19

Block Diagram:

Powersupply

RF Transmitter:

Controller

For

Send Data

According tozone

Encoder RF

transmitter


7/19

RF Receiver:

RF

Receiver

Decoder

Micro

controller

Power supply

16X2 - LCD

Motor driver

DC

Motor

Parkinglight

Horn


8/19

MICROCONTROLLER

The basic architecture of AT89C52 consists of the following features:

Compatible with MCS-52 Products.

8K Bytes of In-System Programmable (ISP) Flash Memory.

4.0V to 5.5V Operating Range.

Fully Static Operation: 0 Hz to 33 MHz.

256 x 8-bit Internal RAM.

32 Programmable I/O Lines.


9/19

Three 16-bit Timer/Counters.

Eight Interrupt Sources.

Full Duplex UART Serial Channel.

Low-power Idle and Power-down Modes.

Interrupt Recovery from Power-down Mode.

Watchdog Timer.

Fast Programming Time.


10/19

AT89S52:


11/19

LCD(Liquid Crystal Display)

LCD (Liquid Crystal Display) screen is an electronic displaymodule and find a wide range of applications. A 16x2 LCD display

is very basic module and is very commonly used in various devices

and circuits. These modules are preferred over seven segments and

other multi segment LEDs. The reasons being: LCDs are

economical; easily programmable; have no limitation of displayingspecial & even custom characters (unlike in seven segments),

animations and so on.

A 16x2 LCD means it can display 16 characters per line and there

are 2 such lines. In this LCD each character is displayed in 5x7 pixelmatrix. This LCD has two registers, namely, Command and Data.


12/19

LCD:


13/19

RF MODULE:

The RF module, as the name suggests, operates at Radio Frequency. Thecorresponding frequency range varies between 30 kHz & 300 GHz.

Transmission through RF is better than IR (infrared) because of many

reasons. Firstly, signals through RF can travel through larger distances

making it suitable for long range applications.

This RF module comprises of an RF Transmitter and an RF Receiver. The

transmitter/receiver (Tx/Rx) pair operates at a frequency of434 MHz. An RF

transmitter receives serial data and transmits it wirelessly through RF through

its antenna connected at pin4. The transmission occurs at the rate of 1Kbps -

10Kbps.The transmitted data is received by an RF receiver operating at the

same frequency as that of the transmitter.


14/19

RF Module Diagram:


15/19

IC 7805:

7805 is a voltage regulator integrated circuit. It is amember of 78xx series of fixed linear voltage regulator

ICs. The voltage source in a circuit may have fluctuations

and would not give the fixed voltage output. The voltage

regulator IC maintains the output voltage at a constantvalue. The xx in 78xx indicates the fixed output voltage it

is designed to provide. 7805 provides +5V regulated power

supply. Capacitors of suitable values can be connected at

input and output pins depending upon the respective

voltage levels.


16/19

IC 7805:

Pin No Function Name

1 Input voltage (5V-18V) Input

2 Ground (0V) Ground

3 Regulated output; 5V (4.8V-5.2V) Output


17/19

ADVANTAGES OF FUTURISTICVEHICLE SYSTEM:

It gives new era in automobiles system.

It reduce accident.

It provide safety on road.

It can control different zone.


18/19

QUERIES


19/19

THANKQ

Documents

Ppt on Future