Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
841 842
COM
PONE
NTS
KNS(Die name Stichers) 70
32
Color
Catalog No. ColorBase unit price
1~4 sets(1 set=10 stickers)
KNSR(Red) B(Blue)
Y(Yellow)
PBX100Y ● With 2 bolt holes, 1 on the side and 1 on the bottom, this box can be fastened from either surface.
PBX150Y
~ SPCC Baking finish (yellow)
SPARE PUNCH BOXES / DIE NAME STICHERS
5
5.5
3.2 3.2100100 1.61.6
13
60
10
4-F11
801.
61.
6
5
5.5
3.2 3.2150100 1.61.6
13
60
10
4-F11
801.
61.
6
~ Seal :PTFE film
Protective film:PP film
■Features ・Can be written on using an oil-based marker or ball-point pen. ・Highly resistant to oil and dirt, and resist peeling.
■Precautions for use ・ Thoroughly wipe off any oil or other substances from the application surface before applying.
It is recommended that paint thinner or another solvent be used to fully remove any oil. ・Use at normal temperatures. ・If the sticker is peeled off and replaced, the adhesive force will diminished.
Order
Days to Ship
Price
Catalog No. - Color
KNS - R
Alteration Code Spec. 1Code
TC
Changes of plate thickness TT-0.02≦TC≦T+0.020.001mm increments �Clearance can be adjusted without using
shims. Cannot be used for T0.3 and T0.4.
WC
W dimension change 8≦WC<W 0.1mm increments
Cannot be used for T0.3 and T0.4.
WKC1W dimension tolerance change Changes W+0.1
0 to 0-0.1.
Cannot be used for T0.3 and T0.4.
Days to Ship
PRECISION MULTIPURPOSE PLATES
UTPB
UTPL Changing the W dimension tolerance
To change W+0.10 to W 0
-0.1,
use alteration WKC1. ~ SKH51 61 ~ 64HRC
Catalog No. W Base unit priceType T 1 ~ 19 pieces
UTPB
0.3 10 13 16 6,6360.4 10 13 16 4,477
0.5 10 13 16 4,05720 25 4,981
1 10 13 16 3,79720 25 4,662
2 10 13 16 3,25920 25 4,150
3 10 13 16 3,37720 25 4,326
5 10 13 16 3,66220 25 4,788
Catalog No. W 0.1mm increments L
Base unit price 1 ~ 19 piecesType T L10.0 ~ 19.9 L20.0 ~ 49.9 L50.0 ~ 79.9 L80.0 ~ 99.9 L100.0 ~ 124.9 L125.0 ~ 150.0
UTPL
0.3 10 13 16
10.0 ~ 150.0
0.4 10 13 16
0.5 10 13 1620 25
1 10 13 1620 25
2 10 13 1620 25
3 10 13 1620 25
5 10 13 1620 25
OrderCatalog No. - W - L
UTPB 2 - 16UTPL 3 - 20 - 50.8
Alteration Code Spec. 1Code
DNC
Addition of press-in lead
�A press-in lead of width 2 mm and depth 0.01 ~ 0.03 is added.
Cannot be used for T0.3 and T0.4.
WHC
A φ1 start hole for W・EDM is added. 2≦X≦L-2 2≦Y≦W-2 0.1mm increments
�Because the hole is machined by discharge machining, the area around the hole will be discolored.
Cannot be used for T0.3 and T0.4.
● Liner: Makes the installation of a block die easier. Using the liner together with shim tape allows the clearance to be adjusted.
● Die spacer: Can be used as an adjustment plate for regrinding.
By changing the plate thickness (TC) of the right and left liners, it is possible to adjust the clearance without using shim tape.
By pushing the liner up with the pin, it can be removed without scratching the die.
● Punches & dies: Because the material is SKH51 (61 ~ 64HRC), these plates can be used for punches and dies.
Price
AlterationsCatalog No. - W(WC) - L -(TC・WKC1・DNC・WHC)
UTPL 2 - 20 - 50.8 - TC2.002UTPL 3 - 25 - 45.6 - WHC-X20.5-Y10.2
Example
0+0.3150
0+
0.1
W
0+
0.1
W
0+0.1L
0+0.003T
0+0.003T
Rolling direction
W
WC
W T
TC 0+0.003
L
W
φ1
X±0.3
Y±0.
3
2
0.01~0.03
Split die
Punch
Liner
Die
Die spacer
Liner
Catalog No.Base unit price
1 ~ 9 pieces
PBX100Y
PBX150Y
OrderCatalog No.
PBX100Y
Days to Ship
Price
■How to use
Use an oil-based marker or ball-point pen to write on the sticker.
Apply the transparent protective film by pressing it tightly onto the seal.
Peal the seal off the backing sheet and apply it to the die.
Sticker
Material width
Control No.
Sticker back
ing sheet
Backing sheet for transparent protective film
Transparent protective film
Backing sheet for transparent protective film
Sticker backing sheet
Transparent protective film