Upload
trinhnguyet
View
219
Download
3
Embed Size (px)
Citation preview
UP
GB
WARRANTY
4th Tray
6th Tray
Wheel Base
2nd Tray
5th Tray
1st Tray
3rd Tray
Wheel base can be pulled
out to extend working base
for greater stability
Tools specifications Art no.
6th Tray (5 sets)
Half Round Rasp
Rubber Mallet
Sprocket Clean Brush
Threadless Nut Setter for installing star-flanged TPS-SP25
TPS-SP33
TPS-SP32
TPS-SP31
nut with 1-1/8” threadless head set system
Threadless Saw Guide TPS-SP26
6th Tray
2nd Tray (9 sets)
DuoHex Tool 6 mm TPS-SP02
Tools specifications Art no.
DuoHex Tool 8 mm TPS-SP03
DuoHex Tool 10 mm TPS-SP04
T-Handle DuoHex 2/2.5/3/4/5/6 mm TPS-SP01Wrench Set
2nd Tray
Tools
4th Tray (9 sets)
Adjustable Spanner
Cable & Housing Cutter
Chainring Nut Wrench
DuoSpoke Wrench
DuoSpoke Wrench
DuoSpoke Wrench
Needle Nose Pliers
PowerLink Pliers
Side Cutting Pliers
specifications Art no.
adjust 0-29mm
TPS-SP16
TPS-SP28
TPS-SP29
TPS-SP30
TPS-SP11
13G/4.3mm TPS-SP13
14G/15G TPS-SP14
M7/M9 TPS-SP15
For easy release of TPS-SP12master links
4th Tray
Tools specifications Art no.
5th Tray (8 sets)
Bottom Bracket Tool TPS-SP17
Cartridge Bottom Bracket Tool TPS-SP18
Cassette Lockring Wrench TPS-SP22
Chain Whip/Sprocket Remover TPS-SP21
Hydraulic Caliper Press Fits all hydraulic TPS-SP23 disc brakes
Pedal Wrench 15mm 15 mm open end wrench
TPS-SP20
RotorTru
Truing disc rotor
TPS-SP24
Universal Crank Puller
TPS-SP19
5th Tray
Tools
3rd Tray (9 sets)
8/10 mm Double Open End Spanner
All Speeds Chain Tool
Chain Hook & Wear Indicator
ComboTorq Wrench & Bit Set
Quad Driver
Shuttle Lever Set
Torx® Wrench Set
specifications
8/10 mm
For multi speed chainup to 11 speed hollow pin chains
Torque Range : 3-12 N.m with 3/4/5/6 mm & T25 tool bits
4/6 mm flat head /#2 Phillips
1 pc long/2 pcs short
T7/T9/T10/T15/T20/T25/T27/T30
(Optional)
T25 DuoTorx® Wrench
Art no.
TPS-SP08
TPS-SP27
TPS-SP09
TPS-SP07
TPS-SP06
TPS-SP05
TPS-SP34
PocketShock DXG TPSMB-DX
3rd Tray
PrepStation TravelCaseArt No. TPS-01PB
PocketShock DXGArt No. TPSMB-DX
HandleLock Button
6mm(0.24”)Padlock hole
(Padlock not included)
TrayLock lever with
padlock hole
TrayLift Lever
User's GuidePrepStation
OPERATION OF PREPSTATION
OPTIONAL ACCESSORIES
Press HandleLock button
to unfold T-handle
Release TrayLock lever PULL down the tray stabilizer Extend wheel base for greater stability
PRESS
Extend tool trays for use
2
PRESS
Press TrayLift lever and raise tool trays
to marked line as shown
1
2-year Warranty: All mechanical components against manufacturer defects only.
Warranty Claim RequirementsTo obtain warranty service, you must have your original sales receipt. Items returned without a sales receipt will assume that the warranty begins on the date of manufacture. All warranties will be void if the product is damaged due to user crash, abuse, system alteration, modification, or used in any way not intended as described in this manual.
* The specifications and design are subject to change without notice.
Please contact your Topeak dealer with any questions. For USA customer service call : 1-800-250-3068
www.topeak.com
Copyright © Topeak, Inc. 2013 M-TPS-01-GB 1/13
* Shimano® is a registered trademark of Shimano® Inc.
* Teflon® is a registered trademark of DuPont.
* Mavic® is a registered trademark of SALOMON S.A.
* Torx® is a registered trademark of the Camcar Corp. division of Textron Inds.
* Campagnolo® is a registered trademark of Campagnolo S.r.I.
Torx® Wrench Set Art no. TPS-SP05Quad Driver Art no. TPS-SP06
T-Handle DuoHex Wrench Set
2mm 3mm 4mm 5mm2.5mm 6mm
ball end side
ball end side
Art no. TPS-SP01 DuoHex Tool
8mm6mm 10mm
Art no. TPS-SP02-04T25 DuoTorx® Wrench Art no. TPS-SP34
Cassette Lockring Wrench Art no. TPS-SP22Chain Whip/Sprocket Remover Art no. TPS-SP21 Side Cutting Pliers Art no. TPS-SP30Needle Nose Pliers Art no. TPS-SP29
RotorTru Art no. TPS-SP24 Hydraulic Caliper Press Art no. TPS-SP23
8/10mm Double Open End SpannerArt no. TPS-SP27
T7 T9 T10 T15 T20 T25 T27 T30
Universal Crank Puller
Tighten puller nut securely into arm
before extracting crank.
One built-in rotating tip and an additional rotating tip
Art no. TPS-SP19
Adjustable Spanner
Art no. TPS-SP28
Before using the crank arm puller ,
remove the crank bolt.
Use correct rotating bit: Built-in rotating tip
for square tapered cranks. Additional rotating
tip for ISIS Drive® and Octalink® crank arms.
Use 8mm Allen wrench to tighten internal
driver of puller to remove crank arm.
CRANK ARM REMOVAL
Pedal Wrench 15mm Art no. TPS-SP20Cartridge Bottom Bracket Tool Art no. TPS-SP18 Art no. TPS-SP28Adjustable SpannerShuttle Lever Set
Bottom Bracket Tool
Remove crank cap
Remove crankarm
Loosen fully any pinch bolts.
Art no. TPS-SP17
Remove crank cap counterclockwise.
Use Bottom Bracket Tool to tighten or remove bearings cups
ADJUSTMENT/DISASSEMBLY OF EXTERNAL BEARING BOTTOM BRACKET
GB User's GuidePrepStation-Tools
3mm 5mm T256mm4mm
T25 Torx Bit
5mm 6
mm
4mm
3mm
yellow plastic lip
NOTE :• Do not twist the yellow plastic lip
as it may break.
• The combotorque wrench & bit
set may only be used to tighten
bolts otherwise this will result in a
loss of calibration.
1
2
USING COMBOTORQ WRENCH & BIT SET
ComboTorq Wrench & Bit Set Art no. TPS-SP07
6mm
Flat Head driver
4mm
Flat Head driver
#2
Phillips driver
#1
Phillips driver
All Speeds Chain Tool Art no. TPS-SP08
* Shimano® is a registered trademark of Shimano® Inc.
* Campagnolo® is a registered trademark of Campagnolo S.r.I.
* Mavic® is a registered trademark of SALOMON S.A.
* Torx® is a registered trademark of the Camcar Corp. division of Textron Inds.
* Teflon® is a registered trademark of DuPont.
2mm Saw
Guide Spacer
1.2mm Saw
Guide Spacer2mm Saw
Guide Spacer
1.2mm Saw
Guide Spacer
Preset
4mm
Allen Key
Half Round Rasp
Art no. TPS-SP31
Option 1 Option 2
For Carbon Saw Blade
DuoSpoke Wrench
DuoSpoke Wrench (13G/4.3mm)
Art no. TPS-SP13
13G(3.5mm)
Shimano®(4.3mm)
DuoSpoke Wrench (14G/15G)
Art no. TPS-SP14
15G(3.2mm)
14G(3.4mm)
Threadless Saw Guide Art no. TPS-SP26
DuoSpoke Wrench (M7/M9)
Art no. TPS-SP15
Mavic®M7
Mavic®M9
Art no. TPS-SP13-15
Rubber Mallet Art no. TPS-SP32 Half Round Rasp Art no. TPS-SP31
Threadless Nut Setter
Rubber Mallet
Art no. TPS-SP32
• Star nut not included
Art no. TPS-SP25
OPERATION OF POWERLINK PLIERS
OPERATION OF CABLE & HOUSING CUTTER
Cable & Housing Cutter
PowerLink Pliers Art no. TPS-SP12
Art no. TPS-SP16
Chainring Nut WrenchSprocket Clean Brush Art no. TPS-SP11Art no. TPS-SP33
Chain Hook & Wear Indicator
" STEP 2 " can fully engage a roller
" STEP 2 " can't engage a roller
2) PRESS " STEP 2 " on a roller
New chain required
Chain in good condition
1)Put " STEP 1 " inside chain space and fully engage a roller
CHAIN WEAR INDICATOR
CHAIN HOOK
Art no. TPS-SP09
GB User's GuidePrepStation-Tools
Copyright © Topeak, Inc. 2013 M-TPS-01-GB 1/13
INSTALLATION INSTRUCTION FOR CAMPAGNOLO® 11-SPEED HOLLOW CHAIN PIN
After pressing the special replacement pin into Campagnolo® 11-Speed chain and breaking off the guide portion, the break off end of the chain rivet is required to be peened to prevent chain failure.
1 2 Before After
3/4 Turn
HOW TO REPLACE CHAIN PIN
Use Chain Hook or Chain Hook & Wear Indicator (optional) to hook chain and hold the target chain rivet in center position.
Snap off new chain pin guide.
1
2
3
Target chain rivet
Chain Hook & Wear Indicator
Art No. TPS-SP09
Press out old chain pin and replace with new chain pin.
Press chain pin as little as necessary to loosen the stiff link.
1. Adjusting Lever2. Chain Tool Plunger Pin 3. Chain Pin Breaker4. Chain Tool Grip5. Rivet Anvil of Hollow Pin
Use Primary Chain Link Fence to install or remove chain pin. Use Secondary Chain Link Fence to loosen stiff links.
Primary Chain Link Fence
Secondary Chain Link Fence
3
1
2
4
5
WARNING
1. When pressing in the chain pin, push down on the top of the chain to keep it fully engaged in the chain tool cradle. Make sure the press pin of the chain tool is centered against the chain pin.
MAINTENANCE1.
2.
Lubricate and maintain tool with Teflon® based lubricant when needed.
To prevent rusting, keep tool dry.
2. Inspect chain rivet again and be sure chain links can bend freely after replacement.
Fits multi-speed chains, including Campagnolo® 11 speed.
USING THREADLESS NUT SETTER
A.
B.